HFBR-4506Z [AVAGO]

Plastic Optical Fiber Cable and Accessories for Versatile Link; 塑料光纤电缆及附件的通用链接


型号：	HFBR-4506Z
厂家：	AVAGO TECHNOLOGIES LIMITED
描述：	Plastic Optical Fiber Cable and Accessories for Versatile Link 塑料光纤电缆及附件的通用链接光纤连接器
文件：	总11页 (文件大小：160K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

HFBR-RXXYYYZ Series (POF)

HFBR-EXXYYYZ Series (POF)

Plastic Optical Fiber Cable and Accessories

forVersatileLink

DataSheet

Cable Description

Features

The HFBR-R/EXXYYYZ series of plastic fiber optic

cables are constructed of a single step-index fiber

sheathed in a black polyethylene jacket. The duplex

fiber consists of two simplex fibers joined with a

zipcord web.

• Compatible with Avago Versatile Link family of

connectors and fiber optic components

• 1 mm diameter Plastic Optical Fiber (POF) in two

grades: low cost standard POF with 0.22 dB/ m typical

attenuation, or high performance extra low loss POF

with 0.19 dB/ m typical attenuation

Standard attenuation and extra low loss POF cables

are identical except for attenuation specifications.

Polyethylene jackets on all plastic fiber cables comply

with UL VW-1 flame retardant specification (UL file #

E89328).

Applications

• Industrial data links for factory automation and plant

control

• Intra-system links; board-to-board, rack-to-rack

• Telecommunications switching systems

• Computer-to-peripheral data links, PC bus extension

• Proprietary LANs

Cables are available in unconnectored or connectored

options. Refer to the Ordering Guide for part number

information.

• Digitized video

• Medical instruments

500

400

300

• Reduction of lightning and voltage transient

susceptibility

• High voltage isolation

200

100

620

640

660

680

700

λ – WAVELENGTH – nm

Figure 1. Typical POF attenuation vs. wavelength.

Plastic Optical Fiber Specifications: HFBR-R/ EXXYYYZ

Absolute Maximum Ratings

Parameter

Symbol

T_S,O

Min.

-55

Max.

+85

+70

Unit

°C

Note

Storage and Operating Temperature

Recommended Operating Temperature

Installation Temperature

T_O

-40

°C

-20

°C

Short Term Tensile

Force

Single Channel

Dual Channel

F_T

100

Short Term Bend Radius

Long Term Bend Radius

Long Term Tensile Load

Flexing

3, 4

F_T

1000

Cycles

Mechanical/ Optical Characteristics, T = -40 to +85°C unless otherwise specified.

Parameter

Symbol

Min.

Typ.^[5]

Max.

Unit

Condition

Cable

Attenuation

Standard Cable,

Type "R"

α_O

0.15

0.22

0.27

dB/ m Source is HFBR-15XXZ

(660 mm LED, 0.5 NA)

Extra Low Loss,

Type "E"

0.15

0.12

0.19

0.16

0.23

0.24

0.19

= 50 meters

Reference

Attenuation

Standard Cable,

Type "R"

α_R

dB/ m Source is 650 nm,

0.5 NA monochrometer,

Extra Low Loss,

Type "E"

= 50 meters

Note 7, Figure 1

Numerical Aperture

D_C

0.46

0.94

2.13

0.47

1.00

2.20

5.0

0.50

1.06

2.27

>2 meters

Diameter, Core and Cladding

Diameter, Jacket

Simplex Cable

Propagation Delay Constant

Mass per Unit Length/ Channel

Cable Leakage Current

l/ v

ns/ m Note 6

5.3

g/ m Without Connectors

I_L

50 kV, = 0.3 meters

Refractive Index

Core

1.492

1.417

Cladding

Notes:

1. Installation temperature is the range over which the cable can be bent and pulled without damage. Below -20°C the cable becomes brittle and

should not be subjected to mechanical stress.

2. Short Term Tensile Force is for less than 30 minutes.

3. Short Term Bend Radius is for less than 1 hour nonoperating.

4. 90° bend on 25 mm radius mandrel. Bend radius is the radius of the mandrel around which the cable is bent.

5. Typical data are at 25°C.

6. Propagation delay constant is the reciprocal of the group velocity for propagation delay of optical power. Group velocity is v=c/ n where c is the

velocity of light in free space (3xl0⁸m/ s) and n is the effective core index of refraction.

7. Note that α_Rrises at the rate of about 0.0067 dB/ °C, where the thermal rise refers to the LED temperature changes above 25°C. Please refer to

Figure 1 which shows the typical plastic optical fiber attenuation versus wavelength at 25°C.

Plastic Fiber Connector Styles

Connector Description

HFBR-4503Z/ 4513Z – Simplex Latching latching connector is available in

parchment, off-white (HFBR-

4506Z).

Four connector styles are available

for termination of plastic optical

fiber: simplex, simplex latching,

duplex and duplex latching. All

connectors provide a snap-in

action when mated to Versatile

Link components. Simplex

connectors are color coded to

facilitate identification of trans-

mitter and receiver connections.

Duplex connectors are keyed so

that proper orientation is ensured

during insertion. If the POF cable/

connector will be used at extreme

operating temperatures or

experience frequent and wide

temperature cycling effects, the

cable/connector attachment can

be strengthened with an RTV

adhesive (see Plastic Connector-

ing Instructions for more detail).

The connectors are made of a

flame retardant VALOX UL94 V-0

material (UL file # E121562).

HFBR-4525Z

HFBR-4516Z – Duplex Latching

The simplex latching connector is

designed for rugged applications

requiring a greater retention force

— 80 Newtons ( 18 lb.) — than

provided by a simplex nonlatching

HFBR-4526Z

connector. When inserting the

simplex latching connector into a

module, the connector latch

mechanism should be aligned with

the top surface of the horizontal

modules, or with the tall vertical

side of the vertical modules.

The duplex latching connector is

designed for rugged applications

requiring greater retention force

than the nonlatching duplex con-

nector. When inserting the duplex

latching connector into a module,

the connector latch mechanism

should be aligned with the top

surface of the dual combination of

horizontal or vertical Versatile Link

components. The duplex latching

connector is available in gray

(HFBR-4516Z).

Misalignment of an inserted

latching connector into either

module will not result in a positive

latch. The connector is released

by depressing the rear section of

the connector lever, and then

pulling the connector assembly

away from the module housing.

SIMPLEX CONNECTOR STYLES

HFBR-4501Z/ 4511Z – Simplex

The simplex latching connector is

available in gray (HFBR-4503Z) or

blue (HFBR-4513Z).

Feedthrough/ Splice

HFBR-4505Z/ 4515Z Bulkhead Adapter

DUPLEX CONNECTOR STYLES

HFBR-4506Z – Duplex

, HFBR-4525Z

The simplex connector provides a

quick and stable connection for

applications that require a

component-to-connector retention

force of 8 Newtons (1.8 lb.).

These connectors are available in

gray (HFBR-4501Z) or blue

(HFBR-4511Z).

HFBR-4526Z

The HFBR-4505Z/4515Z adapter

mates two simplex connectors for

panel/bulkhead feedthrough of

HFBR-4501Z/4511Z terminated

plastic fiber cable. Maximum panel

thickness is 4.1 mm (0.16 inch).

This adapter can serve as a cable

in-line splice using two simplex

connectors. The adapters are

available in gray (HFBR-4505Z)

and blue (HFBR-4515Z). This

adapter is not compatible with POF

duplex, POF simplex latching, or

HCS connectors.

Duplex connectors provide con-

venient duplex cable termination

and are keyed to prevent incorrect

insertion into duplex configured

modules. The duplex connector is

compatible with dual combina-

tions of horizontal or vertical

Versatile Link components (e.g.,

two horizontal transmitters, two

vertical receivers, a horizontal

transmitter with a horizontal

receiver, etc.). The duplex non-

Plastic Optical Fiber Connector Absolute Maximum Ratings

Parameter

Symbol

T_S,O

Min.

-40

Max.

Unit

°C

Note

Storage and Operating Temperature

Recommended Operating Temperature

Installation Temperature

T_O

°C

Nut Torque

HFBR-4505Z/ 4515Z Adapter

T_N

0.7

100

N-m

OzF-in.

Notes:

1. Storage and Operating Temperatures refer to the ranges over which the connectors can be used when not subjected to mechanical stress.

Installation Temperature refers to the ranges over which connectors may be installed onto the fiber and over which connectors can be connected

and disconnected from transmitter and receiver modules.

2. Recommended nut torque is 0.57 N-m.

Plastic Optical Fiber Connector Mechanical/ Optical Characteristics

T = -40 to +85°C, Unless Otherwise Specified.

Parameter

Part Number

Symbol Min. Typ.^[1]Max. Units

Temp. °C Note

Retention Force,

Connector to

Versatile Link

Transmitters and

Receivers

Simplex,

HFBR-4501Z/ 4511Z

F_R-C

+25

-40 to +85

Simplex Latching,

HFBR-4503Z/ 4513Z

+25

-40 to +85

Duplex,

HFBR-4506Z

+25

-40 to +85

Duplex Latching,

HFBR-4516Z

+25

-40 to +85

Tensile Force,

Connector to Cable

Simplex,

HFBR-4501Z/ 4511Z

F_T

8.5

Simplex Latching,

8.5

HFBR-4503Z/ 4513Z

Duplex, HFBR-4506Z

Duplex Latching,

HFBR-4516Z

Adapter Connector

to Connector Loss

HFBR-4505Z/ 4515Z with

HFBR-4501Z/ 4511Z

α_CC

0.7

1.5

2.8

4, 5

Retention Force

Connector to Adapter

HFBR-4505Z/ 4515Z with

HFBR-4501Z/ 4511Z

F_R-B

Insertion Force,

Simplex,

HFBR-4501Z/ 4511Z

Connector to Versatile

Link Transmitters and

Receivers

Simplex Latching,

HFBR-4503Z/ 4513Z

Duplex, HFBR-4506Z

Duplex Latching

HFBR-4516Z

Notes:

1. Typical data are at +25°C.

2. No perceivable reduction in retention force was observed after 2000 insertions. Retention force of non-latching connectors is lower at elevated

temperatures. Latching connectors are recommended for applications where a high retention force at high temperatures is desired.

3. For applications where frequent temperature cycling over temperature extremes is expected, please contact Avago Technologies for alternate

connectoring techniques.

4. Minimum and maximum limit for α_CCfor 0°C to +70°C temperature range. Typical value of α_CCis at +25°C.

5. Factory polish or field polish per recommended procedure.

6. Destructive insertion force was typically at 178 N (40 lb.).

Step-by-Step Plastic Cable

Connectoring Instructions

c) HFBR-4506Z Parchment

(off-white) Duplex

Step 2

Place the crimp ring and connec-

tor over the end of the cable; the

fiber should protrude about 3 mm

(0.12 in.) through the end of the

connector. Carefully position the

ring so that it is entirely on the

connector with the rim of the

crimp ring flush with the connec-

tor, leaving a small space between

the crimp ring and the flange.

Then crimp the ring in place with

the crimping tool. One crimp tool

is used for all POF connector

crimping requirements.

Connector and HFBR-4526Z

Duplex Crimp Ring

The following step-by-step guide

describes how to terminate plastic

fiber optic cable. It is ideal for

both field and factory installation.

Connectors can be easily installed

on cable ends with wire strippers,

cutters and a crimping tool.

d) HFBR-4516Z Gray Latching

Duplex Connector and

HFBR-4526Z Duplex Crimp

Ring

Step 1

Finishing the cable is accom-

plished with the Avago

HFBR-4593Z Polishing Kit,

consisting of a Polishing Fixture,

600 grit abrasive paper and 3 µm

pink lapping film (3M Company,

OC3-14). The connector can be

used immediately after polishing.

The zip cord structure of the

duplex cable permits easy

separation of the channels. The

channels should be separated a

minimum of 100 mm (4 in) to a

maximum of 150 mm (6 in) back

from the ends to permit

For applications with extreme

temperature operation or frequent

temperature cycling, improved

connector to cable attachment

can be achieved with the use of an

RTV (GE Company, RTV-128 or

Dow Corning 3145-RTV)

adhesive. The RTV is placed into

the connector prior to insertion of

the fiber and the fiber is crimped

normally. The connector can be

polished after the RTV has cured

and is then ready for use.

connectoring and polishing.

Materials needed for plastic fiber

termination are:

After cutting the cable to the

desired length, strip off approxi-

mately 7 mm (0.3 in.) of the outer

jacket with the 16 gauge wire

strippers. Excess webbing on the

duplex cable may have to be

trimmed to allow the simplex or

simplex latching connector to

slide over the cable.

1. Avago Plastic Optical Fiber

Cable (Example: HFBR-

RUS500Z, HFBR-RUD500Z,

HFBR-EUS500Z, or HFBR-

EUD500Z)

2. Industrial Razor Blade or Wire

Cutters

3. 16 Gauge Latching Wire

Strippers (Example: Ideal

Stripmaster^TMtype 45-092).

When using the duplex connector

and duplex cable, the separated

duplex cable must be stripped to

equal lengths on each cable. This

allows easy and proper seating of

the cable into the duplex

Note: By convention, pla ce the

gr a y connector on the tr a ns-

mitter ca ble end a nd the blue

connector on the r eceiver ca ble

end to ma inta in color coding

(differ ent color connector s a r e

mecha nica lly identica l).

4. HFBR-4597Z Crimping Tool

5. HFBR-4593Z Polishing Kit

6. One of the following

connectors:

connector.

a) HFBR-4501Z/4503Z Gray

Simplex/Simplex Latching

Connector and HFBR-4525Z

Simplex Crimp Ring

Simplex connector cr imp r ings

ca nnot be used with duplex con-

nector s a nd duplex connector

cr imp r ings ca nnot be used

with simplex connector s beca use

of size differ ences. The simplex

cr imp ha s a dull luster a ppea r -

a nce; the duplex r ing is glossy

a nd ha s a thinner wa ll.

b) HFBR-4511Z/4513Z Blue

Simplex/Simplex Latching

Connector and HFBR-4525Z

Simplex Crimp Ring

dot is no longer visible.

Note: Use of the pink la pping

film fine polishing step r esults

in a ppr oxima tely 2 dB

impr ovement in coupling

per for ma nce of either a

Typica lly, the polishing fixtur e

ca n be used 10 times; 10 duplex

connector s or 20 simplex

connector s, two a t a time.

tr a nsmitter -r eceiver link or a

bulkhea d/ splice over a 600 gr it

polish a lone. This fine polish is

compa r a ble to the Ava go

Place the 600 grit abrasive paper

on a flat smooth surface, pressing

down on the connector, polish the

fiber and the connector using a

figure eight pattern of strokes

until the connector is flush with

the bottom of the polishing

fixture. Wipe the connector and

fixture with a clean cloth or

tissue.

fa ctor y polish. The fine

polishing step ma y be omitted

wher e a n extr a 2 dB of optica l

power is not essentia l, a s with

shor t link lengths. Pr oper

polishing of the tip of the fiber /

connector fa ce r esults in a tip

dia meter between 2.5 mm

(0.098 in.) minimum a nd 3.2

mm (0.126 in.) ma ximum..

Step 4

Place the flush connector and

polishing fixture on the dull side

of the 3 µm pink lapping film and

continue to polish the fiber and

connector for approximately 25

strokes. The fiber end should be

flat, smooth and clean.

Step 3

Any excess fiber protruding from

the connector end may be cut off;

however, the trimmed fiber

should extend at least 1.5 mm

(0.06 in) from the connector end.

HFBR-4593Z Polishing Kit

This cable is now ready for use.

Insert the connector fully into the

polishing fixture with the trimmed

fiber protruding from the bottom

of the fixture. This plastic polish-

ing fixture can be used to polish

two simplex connectors or simplex

latching connectors simultane-

ously, or one duplex connector.

Note: The four dots on the

bottom of the polishing fixtur e

a r e wea r indica tor s. Repla ce

the polishing fixtur e when a ny

Ordering Guide for POF Connectors and Accessories

Plastic Optical Fiber Connectors

HFBR-4501Z Gray Simplex Connector/Crimp Ring

HFBR-4511Z Blue Simplex Connector/Crimp Ring

HFBR-4503Z Gray Simplex Latching Connector with Crimp Ring

HFBR-4513Z Blue Simplex Latching Connector with Crimp Ring

HFBR-4506Z Parchment Duplex Connector with Crimp Ring

HFBR-4516Z Gray Duplex Latching Connector with Crimp Ring

HFBR-4505Z Gray Adapter (Bulkhead/Feedthrough)

HFBR-4515Z Blue Adapter (Bulkhead/Feedthrough)

Plastic Optical Fiber Accessories

HFBR-4522Z 500 HFBR-0500Z Products Port Plugs

HFBR-4525Z 1000 Simplex Crimp Rings

HFBR-4526Z 500 Duplex Crimp Rings

HFBR-4593Z Polishing Kit (one polishing tool, two pieces 600 grit

abrasive paper, and two pieces 3 µm pink lapping film)

HFBR-4597Z Plastic Fiber Crimping Tool

Ordering Guide for POF Cable

For Example:

HFBR-RMD010Z is a Standard

Attenuation, Standard Duplex

Connectored, Duplex, 10 meter

cable.

Cable Length Tolerances:

The plastic cable length

tolerances are: + 10%/-0%.

HFBR-RUD500Z is a Standard

Attenuation, Unconnectored,

Duplex, 500 meter cable.

NOTE: By convention, pre-

connectored simplex POF cables

have gray and blue colored

connectors on the opposite ends

of the same fiber; although

oppositely colored, the

HFBR-RMD100Z is a Standard

Attenuation, Standard Duplex

Connectored, Duplex, 100 meter

cable.

HFBR-RLS001Z is a Standard

Attenuation, Latching Simplex

Connectored, Simplex, 1 meter

cable.

connectors are mechanically

identical. Duplex POF cables with

duplex connectors use color-

coded markings on the duplex

fiber cable to differentiate

between the channel.

HFBR-

RoHS Compliant

Cable Code

Length Code (measured from tip of

connector to tip of connector)

R = Standard Attenuation POF

E = Extra Low Loss POF

Maximum 500 meters (not in 1 meter

increments).

See www.avagotech.com/fiber/cables

e.g., 015 = 15 meters

Connector Code

Channel Code

U = Unconnectored

S = Simplex Cable

N = Standard Simplex Connectors

L = Latching Simplex Connectors

M = Standard Duplex Connectors

T = Latching Duplex Connectors

D = Duplex Zipcord Cable

Note: Not all possible combinations reflect available part numbers. Please contact your local

Avago representative for a list of current available cable part numbers.

Connector Applications

Attachment to Avago Versatile Link Fiber Optic Components

Bulkhead Feedthrough or Panel Mounting for HFBR-4501Z/ 4511Z Simplex Connectors

Versatile Link Mechanical Dimensions

All dimensions in mm (inches).

All dimensions ± 0.25 mm unless otherwise specified.

Fiber Optic Cable Dimensions

Panel Mounting – Bulkhead Feedthrough

1.0 POF

(0.039)

0.230

HCS

(0.009)

HFBR-4505Z (Gray)/ 4515Z (Blue) Adapters

Bulkhead Feedthrough with Two HFBR-4501Z/ 4511Z Connectors

Versatile Link Mechanical Dimensions, continued

HFBR-4516Z (Parchment) Duplex Latching Connector

HFBR-4506Z (Parchment) Duplex Connector

HFBR-4503Z (Gray)/ 4513Z (Blue) Simplex Latching

Connector

HFBR-4501Z (Gray)/ 4511Z (Blue) Simplex Connector

For product information and a complete list of distributors, please go to our website: www.avagotech.com

Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries.

AV01-0150EN May 14, 2006

HFBR-4506Z [AVAGO]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E