K30ANPBGXDQ [BANNER]
EZ-LIGHT® K30 Series Pick-to-Light Sensors;
| 型号： | K30ANPBGXDQ |
| 厂家： | 
Banner Engineering |
| 描述： | EZ-LIGHT® K30 Series Pick-to-Light Sensors |
| 文件： | 总4页 (文件大小：219K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
®
EZ-LIGHT K30 Series Pick-to-Light
Sensors
Datasheet
Compact, Single-Point Devices for Error Proofing of Bin-Picking Operations
•
•
Rugged, cost-effective and easy-to-install multicolor indicator light with pushbutton
Illuminated dome provides an easy-to-see green job light; some models also light
red for alternate operation
•
•
•
•
•
Waterproof IP65 construction for washdown environments
Compact devices are self-contained — no controller needed
Immune to EMI and RFI interference
12 V dc to 30 V dc operation
Cabled and quick disconnect models available
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to
serious injury or death. This device does not include the self-checking redundant circuitry necessary
to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an
energized or de-energized sensor output condition.
Models
1
Model
Function
Output
PNP, NO
NPN, NO
Connection
Job Light
K30APPBGXDQ
K30ANPBGXDQ
K30APPBGRCQ
•
•
Job light is ON at all times while job input is active.
Pressing push button activates output.
Green
•
•
Job light is green while job input is active, until push PNP, NO
button is pushed.
Pressing push button activates output and overrides
job light (it turns Red) for visual verification that
action was sensed.
Green (Red)
Green (Red)
Integral 4-pin M12/
Euro-style quick
disconnect
K30ANPBGRCQ
K30APPBGREQ
K30ANPBGREQ
NPN, NO
PNP, NO
NPN, NO
•
•
•
Job light is ON at all times while job input is active.
Pressing push button activates output.
Pressing push button while job input is inactive
causes unit to light Red, providing visual indication
that sensor is functioning properly.
Overview
The solid-state output interfaces to a system controller, which is pre-programmed for a specific sequence of tasks.
Mounted in or near each bin in an assembler’s work station, the sensor job light signals the assembler:
•
•
Which bins contain items to be picked in a given operation; and
In what order they should be picked.
As the assembler takes a part in sequence and pushes the button, the sensor senses that the part was removed and sends
an output signal to the controller. The controller verifies if the correct part was taken and may respond by turning that job
light OFF, activating the job light of the next bin in the sequence.
If multiple parts are to be removed from one bin, the job light may remain ON until the appropriate number of signals is
returned to the controller. If an incorrect part is selected, the control system may be wired to signal an alarm for the
assembler and/or a supervisor, or it may be programmed to interpret the action as a call for parts.
1
Integral quick disconnect models are listed.
•
•
To order the 2 m (6.5 ft) PVC cable model, omit the suffix "Q" in the model number. For example, K30APPBGXD.
Models with a quick disconnect require a mating cordset.
Original Document
155796 Rev. D
22 November 2016
155796
®
EZ-LIGHT K30 Series Pick-to-Light Sensors
Installation
Install the K30 sensor at such a height and in a location that will be easy for the user and/or supervisor to see the
indicator and comfortable for the user to press the push-button.
Wiring
1 = brown
2 = white
3 = blue
4 = black
1
+
12-30V dc
–
3
4
2
Load
Job Light
Enable ≥ 8V dc
Specifications
Supply Voltage and Current
Job Light Enable
12 V dc to 30 V dc (10% max. ripple) at 50 mA maximum
Input Impedance: 10 KOhms
Input high > 8.0 V
Supply/Output Protection Circuitry
Protected against reverse polarity and transient voltages
Environmental Rating
IEC IP65
Output Rating
Enclosure Type 13
Max. load: 150 mA
ON-state saturation voltage: < 0.5 V at 10 mA dc; < 1.0 V at 150 mA
Construction
dc
Base: polycarbonate
OFF-state leakage current: < 10 μA at 30 V dc
Translucent dome: polycarbonate
Push button: thermoplastic
Output Protection
Required Overcurrent Protection
Protected against false pulse on power-up and continuous overload or
short circuit of output.
WARNING: Electrical connections must be
made by qualified personnel in accordance
with local and national electrical codes and
regulations.
Output Response Time
1 millisecond On and Off
Indicators
Overcurrent protection is required to be provided by end product
application per the supplied table.
Overcurrent protection may be provided with external fusing or via
Current Limiting, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to www.bannerengineering.com.
Job ("Pick") Indicator: Green
Pick Sensed Indicator: Red or OFF, depending on model
Connections
Integral 4-pin M12/Euro-style quick disconnect fitting, PVC-jacketed 2
m (6.5 ft) or 9 m (30 ft) cable, depending on model.
Operating Conditions
Supply Wiring (AWG)
Required Overcurrent Protection (Amps)
−40 °C to +50 °C (−40 °F to +122 °F)
90% at +50 °C maximum relative humidity (non-condensing)
20
22
24
26
28
30
5.0
3.0
2.0
1.0
0.8
0.5
Storage Temperature
−40 °C to +70 °C (−40 °F to +158 °F)
Certifications
2
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 155796 Rev. D
®
EZ-LIGHT K30 Series Pick-to-Light Sensors
Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise.
Accessories
Cordsets
4-Pin Threaded M12/Euro-Style Cordsets
Model
Length
Style
Dimensions
Pinout (Female)
MQDC-406
MQDC-415
MQDC-430
1.83 m (6 ft)
4.57 m (15 ft)
9.14 m (30 ft)
44 Typ.
Straight
M12 x 1
MQDC-450
15.2 m (50 ft)
2
3
ø 14.5
1
4
MQDC-406RA
MQDC-415RA
MQDC-430RA
1.83 m (6 ft)
4.57 m (15 ft)
9.14 m (30 ft)
32 Typ.
[1.26"]
1 = Brown
2 = White
3 = Blue
30 Typ.
[1.18"]
Right-Angle
4 = Black
MQDC-450RA
15.2 m (50 ft)
M12 x 1
ø 14.5 [0.57"]
Brackets
SMB22A
32
•
Right-angle bracket with curved slot
for versatile orientation
C
41
•
•
12-ga. stainless steel
Mounting hole for 22 mm sensor
B
A
46
Hole center spacing: A to B = 26.0
Hole size: A = ø 4.6, B = 4.6 x 16.9, C = 22.2
P/N 155796 Rev. D
www.bannerengineering.com - Tel: +1-763-544-3164
3
®
EZ-LIGHT K30 Series Pick-to-Light Sensors
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp.
will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty
period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION,
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE
OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE
LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER
ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product
previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection
applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval
by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product
specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most
recent version of any documentation, refer to: www.bannerengineering.com.
©
Banner Engineering Corp. All rights reserved
相关型号：
©2020 ICPDF网 联系我们和版权申明