LEDGR70XD5-XM [BANNER]
LED High-Intensity Ring Light;
| 型号： | LEDGR70XD5-XM |
| 厂家： | 
Banner Engineering |
| 描述： | LED High-Intensity Ring Light |
| 文件： | 总4页 (文件大小：349K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LED High-Intensity Ring Light
Datasheet
High-Intensity LED Ring Light for use with PresencePLUS and other Vision Systems
•
•
Compact ring light for PresencePLUS and other Vision Systems
Four extremely bright LEDs for illumination of targets from 0.15 meters to beyond 2
meters (0.49 feet to 6.56 feet)
•
•
•
•
•
Continuous or strobed operation
Optically isolated strobe signal
Fixed or adjustable intensity, depending on model
Maintenance-free, rugged construction
Evenly and intensely illuminates a 610 millimeters (24 inches) diameter at 1 meter (3.28
feet)
Models
1
Model
LED Color
Bracket
Cable
LEDRR70XD5-XQ
LEDWR70XD5-XQ
LEDBR70XD5-XQ
LEDGR70XD5-XQ
LEDIR70XD5-XQ
Red, 620 nm to 630 nm
White, 5000 K to 8300 K
Blue, 465 nm to 485 nm
Green, 520 nm to 535 nm
Infrared, 850 nm
Optional bracket available (see
Mounting Bracket)
150 mm (6 in) pigtail with threaded 5-pin
Euro-style connector
2
LEDUV395R70XD5-XQ
LEDRR70XD5-XM
LEDWR70XD5-XM
LEDBR70XD5-XM
LEDGR70XD5-XM
LEDIR70XD5-XM
UV, 395 nm
Red, 620 nm to 630 nm
White, 5000 K to 8300 K
Blue, 465 nm to 485 nm
Green, 520 nm to 535 nm
Infrared, 850 nm
300 mm (12 in) pigtail with threaded 3-pin
Pico-style connector
Built-in P4 bracket (see dimensions)
3
LEDUV395R70XD5-XM
UV, 395 nm
The following caution applies to UV 395 nm models:
CAUTION:
Risk Group 2: UV Emitted from this product.
Eye or skin irritation may result from exposure. Use appropriate shielding and eye protection. Risk Group 2 (RG
2) products generally do not pose a realistic optical hazard if aversion responses limit the exposure duration or
where lengthy exposures are unrealistic.
- IEC 62471
1
2
3
For models with controllable intensity, add “P” to the model number (e.g., LEDRR70XD5-PQ).
Requires Euro-style cordset.
Connects directly to the P4 sensor.
Original Document
153910 Rev. F
13 March 2019
153910
LED High-Intensity Ring Light
Wiring
PresencePlus Pro
Controller Terminal
Block
Cable Wire
Color
Continuous On
Mode
Wire Purpose
Strobed Mode
4
(2) Strobe (+)
(1) +24V dc
(3) Common
(4) Strobe Common
(5)Active High/Active Low
Figure 1. Pinouts for Mating Cordset
5
Power Wires
Brown (1)
Blue (3)
+24 V dc
common
+24 V dc
common
Pin 01
Pin 02
Active Low: open
Active High: connect to common (Blue wire)
Open — Active Low
Pin 02 — Active High
Strobe Polarity
Control
Gray (5)
open
0 V dc = ON (Active Low)
0 V dc = OFF (Active High)
Strobe common
+5 V dc to 24 V dc = OFF (Active Low)
+5 V dc to 24 V dc = ON (Active High)
White (2)
Black (4)
open
open
Pin 04
Strobe Voltage
Wires
Pin 02
Light Intensity Adjustment
Turn the 270° intensity potentiometer with a small flat-blade screwdriver to adjust the light’s intensity.
1. Apply power to the light and turn the potentiometer all the way clockwise for maximum intensity.
2. If the object to be sensed is too bright at maximum intensity, turn the potentiometer counterclockwise, a little at a time,
testing with the target object, until the correct brightness is achieved.
Specifications
Light Source
Construction
Four high-intensity LEDs; see models table for wavelengths
Enclosure rating: IP50
Housing: aluminum, black anodized
Illumination
Window: acrylic, clear with frosted diffusing surface on inside
Bracket: aluminum, black anodized. Attaches ring light directly to
PresencePLUS P4 with 2 included M4x14 screws
610 mm (24 in) diameter usable light pattern at 1 m
Strobe
Optically isolated
Useful Life
When operated within specifications, output will decrease less than 30ꢀ
Supply Voltage and Current
Operating Voltage: 24 V dc 10ꢀ
Strobe Voltage: 5 V dc to 24 V dc @ 15 mA maximum
Current Draw at Full Intensity: 350 mA maximum
Built-in constant current regulator for LEDs
Potentiometer controls variable intensity for “P” models
Use only with a suitable Class 2 power supply (UL) or SELV power supply (CE)
after 50,000 hours for visible and IR models, 20,000 hours for UV models
Operating Conditions
Temperature: 0 °C to +50 °C (+32 °F to +122 °F)
Humidity: 90ꢀ maximum relative humidity (non-condensing)
Certifications
Light Characteristics
Values shown are typical at 25°C.
Lumens
mWatts
Cool White
390
Green
340
Red
240
Blue
130
IR
UV395
475
LEDxR70
945
4
5
For Banner-supplied wire.
When connecting the light to a PresencePLUS Pro controller terminal block, the controller supply must be 24 V dc 10ꢀ.
2
www.bannerengineering.com - Tel: + 1 888 373 6767
P/N 153910 Rev. F
LED High-Intensity Ring Light
Optical Data
Ring Light
Isolux Pattern
mm
520
250
200
150
100
50
Percentage of Max
Light Intensity (Lux
or mW/m²)
80-100 %
60-80 %
40-60 %
20-40 %
0-20 %
0
50
100
150
200
250
(Mount height of 0.5 meters)
Values shown are typical at 25 °C.
Distance (m)
Max Center Beam Lux (lux)
Max Center Beam Irradiance (mW/m²)
Beam Width (m)
Cool White
Green
Red
Blue
IR
UV395
Vertical
Horizontal
(Spread 29.6°)
(Spread 28.4°)
0.25
0.50
1.00
16,620
14,489
4,490
981
10,228
3,169
692
5,540
1,717
375
40,272
12,479
2,726
20,242
6,272
1,370
0.13
0.26
0.53
0.13
0.25
0.51
5,150
1,125
Dimensions
"Q" Models
"M" Models
36.8 mm
(1.45")
Uses 2X M4 x .5 ISO screws to mount to P4
Intensity adjustment on “P” models only
38.7 mm
(1.52")
76.2 mm
(3.00")
29.2 mm
(1.15")
4X 6-32 UNC - 2BMax. depth 0.180"
to prevent damage to electronics
44.5 mm (1.75")
29.2 mm (1.15")
44.5 mm (1.75")
76.2 mm
(3.00")
Ø 38.4 mm (1.51")
Pico-style
connector
Euro-style connector
All measurements are listed in millimeters [inches], unless noted otherwise.
P/N 153910 Rev. F
www.bannerengineering.com - Tel: + 1 888 373 6767
3
LED High-Intensity Ring Light
Accessories
5-Pin Euro-Style Cordsets
5-Pin Threaded M12/Euro-Style Cordsets—Single Ended
Model
Length
Style
Dimensions
Pinout (Female)
MQDC1-501.5
MQDC1-506
MQDC1-515
0.50 m (1.5 ft)
1.83 m (6 ft)
4.57 m (15 ft)
44 Typ.
Straight
M12 x 1
2
MQDC1-530
9.14 m (30 ft)
ø 14.5
1
4
3
MQDC1-506RA
MQDC1-515RA
1.83 m (6 ft)
5
4.57 m (15 ft)
32 Typ.
[1.26"]
1 = Brown
2 = White
3 = Blue
4 = Black
5 = Gray
30 Typ.
[1.18"]
Right-Angle
MQDC1-530RA
9.14 m (30 ft)
M12 x 1
ø 14.5 [0.57"]
Accessory Brackets
SMBPPRHI
•
•
•
Black zinc plated cold rolled
steel bracket
Mounts directly to
PresencePLUS Pro sensor
Includes: 2 – 6-32 screws
(socket drive, button head)
4 – M3 screws (socket
drive, cap head)
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or
replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not
cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO
BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES
RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT,
STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously
manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the
product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will
void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at
any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to:
www.bannerengineering.com.
For patent information, see www.bannerengineering.com/patents.
©
Banner Engineering Corp. All rights reserved
相关型号：
©2020 ICPDF网 联系我们和版权申明