MQDC-801-5M-806217 [BANNER]
S22 Pro Touch Button;
| 型号： | MQDC-801-5M-806217 |
| 厂家： | 
Banner Engineering |
| 描述： | S22 Pro Touch Button |
| 文件： | 总8页 (文件大小：886K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
S22 Pro Touch Button
Datasheet
22 mm Programmable Multicolor RGB Flush Mount Indicator with Independent Momentary or Latching Touch Button Output
•
Programmable using Banner Pro Editor software and Pro Converter Cable; Pro Editor compatibility applies to all
S22 Pro Touch Button models
•
•
•
•
•
•
Resistance to false triggering by water spray, detergents, oils, and other foreign materials
Rugged, cost-effective, and easy-to-install multicolor indicator with touch button
Waterproof DIN IP69K construction for washdown environments
Up to 7 independent colors in one unit
22 mm threaded polycarbonate base
Ergonomically designed to eliminate hand, wrist, and arm stresses associated with repeated switch operation;
require no physical force to operate
Can be actuated with bare hands or gloves
10 V dc to 30 V dc operation
Terminal connection models available for panel wiring applications
Bimodal inputs and outputs (PNP/NPN), depending on source wiring
•
•
•
•
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This
device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A
sensor failure or malfunction can cause either an energized or de-energized sensor output condition.
Pro Editor
Use Banner's Pro Editor software and Pro Converter Cable to create custom configurations by
selecting different colors, flash patterns, and animations.
For more information visit www.bannerengineering.com/proeditor.
Models
RGB7 Multicolor Models
Output Activation
Function Method
Output
State
Family
Color**
Connection*
Material
S22
A
M
T
S
RGB7
QP
A = Normally Open
R = Normally Closed
T = Touch
S = Standard
F = FDA-grade
Blank = 6-wire 2 m (6.5 ft) integral cable
QP = 150 mm (5.9 in) cable with 8-pin
M12/Euro-style quick disconnect
RGB7 = RGB Multicolor
M = Momentary
L = Latching
* Models with a quick disconnect require a mating cordset
** Green, Red, Yellow, Blue, White, Cyan, Magenta
Three inputs activate seven colors. Touch changes output state.
Original Document
205497 Rev. C
30 October 2018
205497
S22 Pro Touch Button
GRY3 Multicolor Models
Output Activation
Function Method
Output
State
Family
Color**
Connection*
Material
S22
A
M
T
S
GRY3
Q
A = Normally Open
R = Normally Closed
T = Touch
S = Standard
F = FDA-grade
Blank = 5-wire 2 m (6.5 ft) integral PVC cable
Q = Integral 5-pin M12/Euro-style
quick disconnect
GRY3 = Programmable
Multicolor (3 Color, 5-Pin)
QP = 150 mm (5.9 in) PVC cable with 5-pin
M12/Euro-style quick disconnect
T = 5-screw terminal
M = Momentary
L = Latching
* Models with a quick disconnect require a mating cordset
** Green, Red, Yellow
Two inputs activate three colors. Touch changes output state.
One- or Two-Color/Function Models
Output Activation
Function Method
Output
State
Color 1/
Job
Color 2/
Sense
Family
Function
Connection*
Material
S22
A
M
T
S
G
R
H
Q
A = Normally Open
R = Normally Closed
T = Touch
S = Standard
F = FDA-grade
G = Green
R = Red
Y = Yellow
B = Blue
W = White
X = Not Used
Blank = 5-wire 2 m (6.5 ft) integral PVC cable
Q = Integral 5-pin M12/Euro-style
quick disconnect
QP = 150 mm (5.9 in) PVC cable with 5-pin
M12/Euro-style quick disconnect
T = 5-screw terminal
H = Illuminated Buttons
C = Pick-to-Light **
E = Pick-to-Light **
D = Pick-to-Light **
M = Momentary
L = Latching
* Models with a quick disconnect require a mating cordset
** Latching output function not available
H Logic: Power activates Color 1. Touch changes output state and activates Color 2. Latch and momentary options.
C Logic: Input activates Color 1. Touch activates Color 2 and Output.
E Logic: Input activates Color 1. Touch activates Output. Touch with inactive input activates Color 2.
D Logic: Input activates Color 1. Touch activates Output.
One-, Two-, or Three-Color/Function Models
Output Activation
Function Method
Output
State
Color 1/
Job
Color 2/ Color 3/
Mispick Sense
Family
Function
Connection*
Material
S22
A
M
T
S
G
R
C3
Q
Y
A = Normally Open
R = Normally Closed
T = Touch
S = Standard
F = FDA-grade
G = Green
R = Red
Y = Yellow
B = Blue
Blank = 5-wire 2 m (6.5 ft) integral PVC cable
Q = Integral 5-pin M12/Euro-style
quick disconnect
QP = 150 mm (5.9 in) PVC cable with 5-pin
M12/Euro-style quick disconnect
T = 5-screw terminal
C3 = Specialty Pick-to-Light
C4 = Specialty Pick-to-Light
M = Momentary
W = White
* Models with a quick disconnect require a mating cordset
C3 Logic: Input activates Color 1. Touch with active input activates Color 3 and Output. Touch with inactive input activates Color 2 and Output. 500
ms leading edge off-delay.
C4 Logic: Input activates Color 1. Touch with active input activates Color 3 and Output. Touch with inactive input activates Color 2 and Output for 5
seconds. 500 ms leading edge off-delay.
2
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 205497 Rev. C
S22 Pro Touch Button
Wiring Diagrams
RGB7 Multicolor Models
NPN
PNP
Key
Pin 1 = White
Pin 2 = Brown
Pin 3 = Green
Pin 4 = Yellow
Pin 5 = Gray
Pin 6 = Pink
Pin 7 = Blue
Pin 8 = Red
2
7
1
3
2
7
1
3
–
+
10-30V dc
+
10-30V dc
–
Load
Load
1
2
3
1
2
3
8
4
5
6
8
4
5
6
N/C
N/C
N/C
N/C
Table 1: RGB Multicolor Color/Function Definition
Red
X
Yellow
Green
X
Cyan
Blue
Magenta
White
Input 1
Input 2
Input 3
X
X
X
X
X
X
X
X
X
X
GRY3 Multicolor Models
NPN
PNP
Key
Pin 1 = Brown
Pin 2 = White
Pin 3 = Blue
Pin 4 = Black
Pin 5 = Gray
1
3
1
3
–
+
10-30V dc
+
10-30V dc
–
4
2
5
4
2
5
Load
Load
Touch toggles output
1
2
1
2
Table 2: GRY3 Multicolor Color/Function Definition
Green
X
Yellow
Red
X
Input 1
Input 2
X
X
One- or Two-Color/Function; C, D, and E Logic Models
NPN
PNP
Key
Pin 1 = Brown
Pin 2 = White
Pin 3 = Blue
Pin 4 = Black
Pin 5 = Gray
1
1
3
–
+
10-30V dc
+
10-30V dc
–
3
4
4
Load
Load
2
2
5
C1
C1
5
Not Used
Not Used
P/N 205497 Rev. C
www.bannerengineering.com - Tel: +1-763-544-3164
3
S22 Pro Touch Button
One- or Two-Color/Function; H Logic Models
NPN
PNP
Key
Pin 1 = Brown
Pin 2 = White
Pin 3 = Blue
Pin 4 = Black
Pin 5 = Gray
1
1
3
–
+
10-30V dc
+
10-30V dc
–
3
4
4
2
5
Load
Load
2
Not Used
Not Used
Not Used
5
Not Used
One-, Two-, or Three-Color/Function; C3 & C4 Logic Models
NPN
PNP
Key
Pin 1 = Brown
Pin 2 = White
Pin 3 = Blue
Pin 4 = Black
Pin 5 = Gray
1
1
3
–
+
10-30V dc
+
10-30V dc
–
3
4
4
Load
Load
2
2
5
C1
C1
5
Not Used
Not Used
Cabled wiring diagrams are shown. Quick disconnect wiring diagrams are functionally identical.
4
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 205497 Rev. C
S22 Pro Touch Button
Specifications
Supply Voltage
10 V dc to 30 V dc
Pro Editor Configuration
Connection to Pro Editor software enables control of:
•
•
Animation: Steady, Flash, Two Color Flash, Intensity Sweep, Demo
Color: Green, Red, Yellow, Blue, White, Cyan, Magenta, Amber, Rose, Lime
Green, Orange, Sky Blue, Violet, Spring Green
Supply Current
80 mA maximum current at 10 V dc (exclusive of load)
70 mA maximum current at 12 V dc (exclusive of load)
45 mA maximum current at 24 V dc (exclusive of load)
40 mA maximum current at 30 V dc (exclusive of load)
•
•
•
Intensity: Low, Medium, High
Speed: Slow, Standard, Fast
Output State: Normally Open, Normally Closed, Momentary, Latching, On
Delay, Off Delay
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
•
Logic Type: Three State Advanced Control (F2 Mode), Seven State
Advanced Control (F2 Mode), Four State Full Logic (Custom)
Output Rating
Maximum Load: 150 mA
ON-state saturation voltage: <2 V dc at 10 mA; <2.5 V dc at 150 mA
OFF-state leakage current: <10 μA at 30 V dc
Pro Converter Cable required to interface between PC and indicator, see accessories
Default Indicator Characteristics
1
Color Coordinates
Lumen
Output
(Typical at
25 °C)
Dominant Wavelength
(nm)or Color Temperature
(CCT)
Leakage Current Immunity
400 µA
Color
x
y
Response Time
Power-Up Delay: 250 milliseconds maximum
Input Response: 20 milliseconds maximum
Output Response: 300 milliseconds maximum
Green
527
625
572
465
5700K
492
–
0.178
0.699
0.438
0.141
0.328
0.192
0.354
0.520
0.506
0.350
0.167
0.594
0.184
0.167
0.700
0.297
0.500
0.056
0.337
0.336
0.149
0.434
0.213
0.564
0.240
0.379
0.085
0.517
0.175
0.075
0.250
0.025
0.240
0.195
0.095
0.165
0.085
0.210
0.165
0.130
0.045
0.180
Red
Touch Dwell Time
Yellow
Blue
If touch dwells for longer than 60 seconds, the output will revert back to the
untouched state.
White
Connections
Cyan
5-pin or 8-pin integral M12/Euro-style quick disconnect, 2 m (6.5 ft) integral PVC
cable, or 5-pin or 8-pin 150 mm (5.9 inch) PVC cable with a M12/Euro-style quick
disconnect, depending on model
Magenta
Amber
Rose
585
–
Models with a quick disconnect require a mating cordset
Mounting
M22 by 1.5 threaded base, maximum torque 2.25 N·m (20 inch·lbf)
Lime Green
Sky Blue
Orange
Violet
557
485
597
424
507
Construction
Standard Model Base, Dome, and Nut: Polycarbonate
FDA Model Base, Dome, and Nut: FDA-grade copolyester
Vibration and Mechanical Shock
Meets IEC 60068-2-6 requirements (Vibration: 10 Hz to 55 Hz, 1.0 mm amplitude, 5
Spring Green
minutes sweep, 30 minutes dwell)
Meets IEC 60068-2-27 requirements (Shock: 30G 11 ms duration, half sine wave)
Operating Conditions
–40 °C to +50 °C (–40 °F to +122 °F)
90% at +50 °C maximum relative humidity (non-condensing)
Storage Temperature: –40 °C to +70 °C (–40 °F to +158 °F)
Required Overcurrent Protection
WARNING: Electrical connections must be made by
qualified personnel in accordance with local and
national electrical codes and regulations.
Environmental Rating
Standard Models: IEC IP66, IEC IP67, DIN IP69K
Cabled models also meet DIN IP69K if the cable and cable entrance are protected
from high-pressure spray
Overcurrent protection is required to be provided by end product application per the
supplied table.
Indicator side of terminal models meet DIN IP69K when installed in an enclosure
Screw connection points meet IEC IP00
Overcurrent protection may be provided with external fusing or via Current Limiting,
Class 2 Power Supply.
FDA Models: IEC IP66, IEC IP67, and DIN IP69K
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to www.bannerengineering.com.
Certifications
Supply Wiring (AWG)
Required Overcurrent Protection (Amps)
20
22
24
26
28
30
5.0
3.0
2.0
1.0
0.8
0.5
Dimensions
Quick-Disconnect Models
Terminal Models
Cabled Models
4.0
[0.16]
4.0
[0.16]
4.0
[0.16]
M22 x 1.5
M22 x 1.5
M22 x 1.5
25.7
[1.01]
25.7
[1.01]
25.7
[1.01]
40.2
[1.58]
39.1
[1.54]
47.8
[1.88]
ø 20.5
[0.81]
ø 20.5
[0.81]
1
Refer to the CIE 1930 (x,y) Chromaticity Diagram, to show equivalent color with indicated color coordinates.
P/N 205497 Rev. C
www.bannerengineering.com - Tel: +1-763-544-3164
5
S22 Pro Touch Button
All measurements are listed in millimeters [inches], unless noted otherwise.
Accessories
Pro Editor Hardware
MQDC-506-USB
CSB-M1251FM1251M
•
Pro Converter Cable
•
5-pin parallel Y splitter (Male-Male-
Female)
•
1.83 m (6 ft) M12/Euro-style quick
disconnect to Device and USB to PC
Required for connection to Pro Editor
•
•
For full Pro Editor preview capability
Requires external power supply, sold
separately
•
PSW-24-1
ACC-PRO-CABLE5
•
•
24 V dc, 1 A power supply
2 m (6.5 ft) PVC cable with M12/Euro-
style quick disconnect
Provides external power with splitter
cable, sold separately
•
Mating accessory for cabled and
terminal models
•
150 mm (6 inch) PVC cable with M12/
Euro-style quick disconnect
Lever wire nuts included (qty 5)
Required to connect cabled models to
Pro Converter Cable, sold separately
•
•
•
x5
MQDC-801-5M-806217
•
•
8-pin to 5-pin double-ended cordset
0.31 m (1 ft) PVC cable with M12/Euro-
style quick disconnects
•
Required to connect 8-pin Pro Series-
enabled devices to Pro Converter Cable
(MQDC-506-USB), sold separately
Cordsets
5-Pin Threaded M12/Euro-Style Cordsets—Single Ended
Model
Length
Style
Dimensions
Pinout (Female)
MQDC1-501.5
MQDC1-506
MQDC1-515
0.50 m (1.5 ft)
1.83 m (6 ft)
4.57 m (15 ft)
44 Typ.
Straight
M12 x 1
ø 14.5
MQDC1-530
9.14 m (30 ft)
2
1
4
MQDC1-506RA
MQDC1-515RA
1.83 m (6 ft)
3
5
4.57 m (15 ft)
32 Typ.
[1.26"]
1 = Brown
2 = White
3 = Blue
4 = Black
5 = Gray
30 Typ.
[1.18"]
Right-Angle
MQDC1-530RA
9.14 m (30 ft)
M12 x 1
ø 14.5 [0.57"]
5-Pin Threaded M12/Euro-Style Cordsets—Washdown Stainless Steel
Model
Length
Style
Dimensions
Pinout (Female)
MQDC-WDSS-0506
MQDC-WDSS-0515
1.83 m (6 ft)
2
4.57 m (15 ft)
1
4
3
5
Ø15.5 mm
Straight
1 = Brown
2 = White
3 = Blue
Ø4.8 mm
MQDC-WDSS-0530
9.14 m (30 ft)
43.5 mm
4 = Black
5 = Gray
6
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 205497 Rev. C
S22 Pro Touch Button
8-Pin Threaded M12/Euro-Style Cordsets with Open-Shield
Model
Length
Style
Dimensions
Pinout (Female)
MQDC2S-806
MQDC2S-815
MQDC2S-830
1.83 m (6 ft)
4.57 m (15 ft)
9.14 m (30 ft)
44 Typ.
Straight
2
3
M12 x 1
MQDC2S-850
15.2 m (50 ft)
4
1
7
6
ø 14.5
5
MQDC2S-806RA
MQDC2S-815RA
MQDC2S-830RA
1.83 m (6 ft)
4.57 m (15 ft)
9.14 m (30 ft)
8
32 Typ.
[1.26"]
1 = White
2 = Brown
3 = Green
4 = Yellow
5 = Gray
6 = Pink
30 Typ.
[1.18"]
Right-Angle
MQDC2S-850RA
15.2 m (50 ft)
7 = Blue
M12 x 1
ø 14.5 [0.57"]
8 = Red
8-Pin Threaded M12/Euro-Style Cordsets with Open-Shield—Washdown, Stainless Steel
Model
Length
Style
Dimensions
Pinout (Female)
MQDC-WDSS-0806
1.83 m (6 ft)
2
3
4
44 Typ.
1
MQDC-WDSS-0815
MQDC-WDSS-0830
4.57 m (15 ft)
9.14 m (30 ft)
7
6
5
Straight
8
M12 x 1
ø 14.5
1 = White
2 = Brown
3 = Green
4 = Yellow
5 = Gray
6 = Pink
7 = Blue
8 = Red
Brackets
SMB22A
SMB22FVK
32
46
118
•
Right-angle bracket with curved slot for versatile
orientation
•
•
•
V-clamp, flat bracket and fasteners for
mounting to pipe or extensions
C
ø22.5
•
•
12-ga. stainless steel
Clamp accommodates 28 mm diameter tubing
or 1 in. square extrusions
22 mm hole for mounting sensor
41
Mounting hole for 22 mm sensor
A
B
34
A
46
Hole size: A = ø 22.5
Hole center spacing: A to B = 26.0
Hole size: A = ø 4.6, B = 4.6 x 16.9, C = 22.2
45
SMB22RAVK
SMBAMS22P
A
•
•
•
V-clamp, right-angle bracket and fasteners for
•
Flat SMBAMS series bracket with 22 mm hole
for mounting sensors
C
mounting to pipe or extensions
46
Clamp accommodates 28 mm diameter tubing
or 1 in. square extrusions
22 mm hole for mounting sensor
•
•
Articulation slots for 90+° rotation
12-ga. (2.6 mm) cold-rolled steel
A
B
93
90
57
Hole size: A = ø 22.5
Hole center spacing: A = 26.0, A to B = 13.0
Hole size: A = 26.8 x 7.0, B = ø 6.5, C = ø 22.5
P/N 205497 Rev. C
www.bannerengineering.com - Tel: +1-763-544-3164
7
S22 Pro Touch Button
Ø A
SMBAMS22RA
TC-K30-CL
45
•
Right-angle SMBAMS series bracket with 22
•
Touch cover
mm hole for mounting sensors
Articulation slots for 90+° rotation
12-ga. (2.6 mm) cold-rolled steel
C
•
•
53
B
A
B
48
Diameter: A = 40.7
Height: B = 31
Hole center spacing: A = 26.0, A to B = 13.0
Hole size: A = 26.8 x 7.0, B = ø 6.5, C = ø 22.5
All measurements are listed in millimeters, unless noted otherwise.
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge,
any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the
improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER
PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR
FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner
Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such
purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this
document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is
provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com.
For patent information, see www.bannerengineering.com/patents.
FCC Part 15 and CAN ICES-3 (B)/NMB-3(B)
This device complies with part 15 of the FCC Rules and CAN ICES-3 (B)/NMB-3(B). Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and CAN ICES-3 (B)/NMB-3(B). These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the manufacturer.
©
Banner Engineering Corp. All rights reserved
相关型号：
©2020 ICPDF网 联系我们和版权申明