Q45AD9CVQ [BANNER]

Q45AD9 NAMUR Series Sensor;


型号：	Q45AD9CVQ
厂家：	Banner Engineering
描述：	Q45AD9 NAMUR Series Sensor
文件：	总10页 (文件大小：613K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Q45AD9 NAMUR Series Sensor

Datasheet

No revision without agency approval.

•

Designed for use with approved ampliﬁers and intrinsically safe barriers in

explosive environments

•

NAMUR compliant sensor with the rugged design and excepꢀonal opꢀcal

performance of Q45 series sensors

Output passes ≤ 1.2 mA in the “dark” condiꢀon and ≥ 2.1 mA in the “light”

condiꢀon

Internal mulꢀ-turn SENSITIVITY (Gain) control accessible beneath hinged, o-ring

sealed top cover

•

Models are available with an integral cable or a quick-disconnect connector

Supply voltage: 5 to 15 V dc

WARNING: Not To Be Used for Personnel Protecꢀon

Never use this device as a sensing device for personnel protecꢀon. Doing so could lead to serious injury or death.

This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety

applicaꢀons. A sensor failure or malfuncꢀon can cause either an energized or de-energized sensor output

condiꢀon.

Models

Standard 2 m (6.5 ꢁ) cable models are listed. To order the 9 m (30 ꢁ) cable model, add suﬃx "W/30" to the cabled model number

(Q459E W/30). Models with a QD connector require a maꢀng cable (see Accessories list).

Opposed Models - Emiꢁer (E) and Receiver (R)

Models

Cable

Performance

Output Type

Q459E

2 m (6.5 ꢁ)

4-Pin Euro QD

2 m (6.5 ꢁ)

4-Pin Euro QD

Constant current

Q459EQ

Q45AD9R

Q45AD9RQ

880 nm, infrared

≤ 1.2 mA dark

≥ 2.1 mA light

Range: 6meters (20 feet)

Retroreꢂecꢀve Models

Retroreꢂecꢀve range is speciﬁed using one model BRT-3 P retroreꢂector (3-inch diameter). Actual sensing range may be more or less

than speciﬁed, depending upon the eﬃciency and reꢂecꢀve area of the retroreꢂector(s) in use.

Non-Polarized Models

Cable

Performance

Output Type

Q45AD9LV

2 m (6.5 ꢁ)

Constant Current

680 nm, visible red

≤ 1.2 mA dark

≥ 2.1 mA light

Range: 9 m (30 ꢁ)

Q45AD9LVQ

4-pin Euro QD

Polarized Models

Cable

Performance

Output Type

Q45AD9LP

2 m (6.5 ꢁ)

Constant Current

680 nm, visible red

≤ 1.2 mA dark

≥ 2.1 mA light

Range: 6 m (20 ꢁ)

Q45AD9LPQ

4-pin Euro QD

Diﬀuse Models

Performance curves are based on a 90% reꢂectance white test card.

Original Document

38343 Rev. K

3 April 2017

38343

Q45AD9 NAMUR Series Sensor

Short Range Models

Cable

Performance

Output Type

Q45AD9D

2 m (6.5 ꢁ)

Constant Current

880 nm, infrared

≤ 1.2 mA dark

≥ 2.1 mA light

Range: 300 mm (12 in)

Q45AD9DQ

4-pin Euro QD

Long Range Models

Cable

Performance

Output Type

Q45AD9DL

2 m (6.5 ꢁ)

Constant Current

880 nm, infrared

Range: 1 m (40 in)

≤ 1.2 mA dark

≥ 2.1 mA light

Q45AD9DLQ

4-pin Euro QD

Convergent Models

Convergent mode models operate at 680 nm, visible red. Performance curves are based on a 90% reꢂectance white test card.

Models

Cable

Focus

Output Type

Q45AD9CV

2 m (6.5 ꢁ)

Constant Current

38 mm (1.5 in)

≤ 1.2 mA dark

≥ 2.1 mA light

Spot size at focus: 1.3 mm (0.05 in)

Q45AD9CVQ

Q45AD9CV4

Q45AD9CV4Q

4-pin Euro QD

2 m (6.5 ꢁ)

Constant Current

100 mm (4 in)

≤ 1.2 mA dark

≥ 2.1 mA light

Spot size at focus: 1.5 mm (0.06 in)

4-pin Euro QD

Plasꢀc Fiber Opꢀc Models

Performance curves are based on a 90% reꢂectance white test card.

Models

Cable

Performance

Output Type

Q45AD9FP

2 m (6.5 ꢁ)

660 nm, visible red

Constant Current

Range: varies by sensing mode and ﬁber

opꢀcs used

≤ 1.2 mA dark

≥ 2.1 mA light

Q45AD9FPQ

4-pin Euro QD

Glass Fiber Opꢀc Models

Performance curves are based on a 90% reꢂectance white test card.

Models

Cable

Performance

Output Type

Q45AD9F

2 m (6.5 ꢁ)

880 nm, infrared

Constant Current

Range: varies by sensing mode and ﬁber

opꢀcs used

≤ 1.2 mA dark

≥ 2.1 mA light

Q45AD9FQ

4-pin Euro QD

Models

Cable

Performance

Output Type

Q45AD9FV

2 m (6.5 ꢁ)

650 nm, visible red

Constant Current

Range: varies by sensing mode and ﬁber

opꢀcs used

≤ 1.2 mA dark

≥ 2.1 mA light

Q45AD9FVQ

4-pin Euro QD

Overview

The Q45AD9 Series NAMUR Sensor is a rugged, self-contained two-wire sensor designed for use with cerꢀﬁed intrinsically safe switching

ampliﬁers and barriers (Approved Apparatus) with intrinsically safe circuits.

The Q45AD9 Series NAMUR sensor is designed in accordance with DIN 19234 (IEC/EN 60947-5-6) for operaꢀon via two-wire connecꢀon

to an Approved Apparatus controlled by the variable internal resistance of the sensor.

The sensor varies the impedance across the sensor output, which passes 1 mA or less in the "dark" condiꢀon and 2 mA or more in the

"light" condiꢀon. A highly visible red LED indicator is located beneath a raised transparent dome on top of the sensor.

•

SIGNAL—LED lights red when the sensor sees its modulated light source

POWER (Emiꢃers only)—LED lights red when 5 to 15 V dc power is applied

Mulꢀ-turn sensiꢀvity control on top of sensor, beneath a transparent cover, allows precise sensiꢀvity seꢄng (turn clockwise to increase

gain).

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 38343 Rev. K

Q45AD9 NAMUR Series Sensor

Models are available with either a 2 m (6.5 ꢁ) or 9 m (30 ꢁ) long aꢃached PVC-covered cable, or a 4-pin M12/Euro-style quick

disconnect (QD) connector. Quick disconnect models (with Q in the model number suﬃx) use MQD9-4.. maꢀng cable (either straight or

right angle connector; see Accessories on page 9). Contact Banner Engineering for the availability of sensor models with 9 m (30 ꢁ)

long aꢃached cable.

Installaꢀon Instrucꢀons

Ex/HazLoc Applicaꢀons

WARNING:

•

Explosive Atmospheres/Hazardous Locaꢀons

The user has the responsibility to ensure that all local, state, and naꢀonal laws, rules, codes, or regulaꢀons

relaꢀng to the installaꢀon and use of this Banner device in any parꢀcular applicaꢀon are saꢀsﬁed. This

Banner device must be installed by Qualiﬁed Persons, in accordance with this document and applicable

regulaꢀons.

•

A Qualiﬁed Person is a person who, by possession of a recognized degree or cerꢀﬁcate of professional

training, or who, by extensive knowledge, training and experience, has successfully demonstrated the

ability to solve problems relaꢀng to the subject maꢃer and work.

WARNING:

•

Explosion Hazard

Do not disconnect equipment unless the power has been switched oﬀ or the area is known to be non-

hazardous.

CAUTION: Electrostaꢀc Discharge (ESD)

Special Condiꢀons for Safe Use. Parts of the enclosure are non-conducꢀng and may generate an igniꢀon-capable

level of ESD. Cleaning of the equipment shall be done only with a damp cloth.

General Notes and Condiꢀons for Safe Use:

•

See Speciﬁcaꢀons and Wiring Diagrams for important informaꢀon concerning enꢀty parameters, permissible locaꢀons,

electrical connecꢀons and cerꢀﬁcaꢀons.

•

In addiꢀon to the warning above concerning user responsibility, the installaꢀon must comply with the following:

◦

All installaꢀons must comply with all manufacturer's instrucꢀons.

U.S. Installaꢀons: The relevant requirements of the Naꢀonal Electrical Code (ANSI/NFPA-70 (NEC ) and when

appropriate ANSI/ISA-RP12.06.01 Installaꢀon of Intrinsically Safe Systems for Hazardous (Classiﬁed) Locaꢀons.

Canadian Installaꢀons: The relevant requirements of the Canadian Electrical Code (CSA C22.1).

◦

ATEX and IECEx Installaꢀons: The relevant requirements of EN 60079-14 and applicable Naꢀonal regulaꢀons.

•

Do not aꢃempt any repairs to this Banner device; it contains no ﬁeld-replaceable parts or components. Tampering and/or

replacement with non-factory components may adversely aﬀect the safe use of the system.

Approved Apparatus enꢀty parameters must meet the following requirements:

◦

V_ocor V_t≤ V_max

C_a≥ C_i+ C_cable

I_scor I_t≤ I_max

La ≥ L_i+ L_cable

•

Sensor Enꢀty Parameters:

◦

V_max(Ui) ≤ 15 V dc

I_max(li) ≤ 60 mA

P_i≤ 225 mW

C_i= 0.3 μF

L_i= 0 mH

•

Cable Enꢀty Parameters (if unknown):

◦

C_cable= 60 pF/ꢁ

L_cable= 0.2 µH/ꢁ

•

The ambient operaꢀng temperature range of the Sensors is −40 °C to +70 °C (−40 °F to +158 °F).

For U.S. installaꢀons, Class II and III, Division 2 applies only to model numbers ending in a Q suﬃx.

For intrinsically safe installaꢀons, sensors must be used with cerꢀﬁed intrinsically safe switching ampliﬁers and barriers

(Approved Apparatus) with intrinsically safe circuits that limit supply voltage and current in the event of failures.

Associated Apparatus is not required for installaꢀon of the devices within a Division 2 hazardous (classiﬁed) locaꢀon when

installed per the Naꢀonal Electrical Code. The maximum voltage for Division 2 installaꢀon is 15V dc. In Division 2 installaꢀons

(without Associated Apparatus), observe Explosion Hazard warning at the beginning of this secꢀon.

Associated Apparatus is not required for installaꢀon of the devices within a Division 2 hazardous (classiﬁed) locaꢀon when

installed in, or through the wall of a suitable enclosure with provision for connecꢀon of rigid metal conduit per the Canadian

Electrical Code, as acceptable to the local inspecꢀon authority having jurisdicꢀon. The maximum raꢀng for Division 2

installaꢀon is 15V dc, 60 mA. In Division 2 installaꢀons (without Associated Apparatus), observe Explosion Hazard warning at

the beginning of this secꢀon.

•

Maximum non-hazardous area voltage that the Approved Apparatus (intrinsically safe circuit) is connected to must not exceed

250V.

P/N 38343 Rev. K

www.bannerengineering.com - Tel: +1-763-544-3164

Q45AD9 NAMUR Series Sensor

•

Intrinsic safety ground, if required for the Associated Apparatus, shall be less than 1 ohm.

Maximum connector torque: 6 ꢁ-lbs.

Wiring Connecꢀons

Q45AD9 Series NUMAR sensors are intrinsically safe ONLY when used with cerꢀﬁed intrinsically safe switching ampliﬁers and barriers

(Approved Apparatus) with intrinsically safe circuits. Banner does not manufacture such devices; however, our applicaꢀons engineers

can refer you to suppliers of cerꢀﬁed devices that will interface with Banner sensors.

The user is responsible for proper installaꢀon and maintenance of this equipment, and must conform with the cerꢀﬁcaꢀon

requirements relaꢀng to barriers and to maximum allowable capacitance and inductance of the ﬁeld wiring. If in doubt about these

requirements, our applicaꢀons engineers can refer you to the appropriate authority.

NAMUR Sensors with Aꢁached Cable

NAMUR Sensors with Quick-Disconnect

Hazardous Area

Non-hazardous Area

Hazardous Area

Non-hazardous Area

NAMUR Sensor

Approved Apparatus

NAMUR Sensor

Approved Apparatus

–

Sensor

Input

Power

≤ 15 V dc

Power

–

Sensor

Input

–

Output

Speciꢃcaꢀons for Q45 NAMUR Sensors

Supply Voltage and Current

Indicators

5 to 15 V dc. Supply voltage is provided by the ampliﬁer to which the sensor is

Indicator LEDs are highly visible, located beneath a raised transparent dome on

connected.

top of the sensor.

POWER (red) LED (emiꢃers only) lights whenever 5 to 15 V dc power is applied

SIGNAL (red) LED lights whenever the sensor sees its modulated light source

Adjustments

Mulꢀ-turn sensiꢀvity control on top of sensor, beneath a transparent o-ring

sealed cover, allows precise sensiꢀvity seꢄng (turn clockwise to increase gain).

Connecꢀons

PVC-jacketed 2 m (6.5 ꢁ) or 9 m (30 ꢁ) cables, or 4-pin Euro-style quick-

disconnect (QD) ﬁꢄng are available. QD cables are ordered separately. See

Accessories.

Output

Constant current output: ≤ 1.2 mA in the “dark” condiꢀon and ≥ 2.1 mA in the

“light” condiꢀon

Operaꢀng Condiꢀons

Output Response Time

Temperature: −40 °C to +70 °C (−40 °F to +158 °F)

Maximum relaꢀve humidity: 90% at 50 °C (non-condensing)

Opposed mode receiver: 2 milliseconds on/0.4 milliseconds oﬀ. All others 5

milliseconds on/oﬀ (does not include ampliﬁer response)

Cerꢀꢃcaꢀons

Construcꢀon

Molded thermoplasꢀc polyester housing, o-ring sealed transparent Lexan top

cover, molded acrylic lenses, and stainless steel hardware. Q45s are designed

to withstand 1200 psi washdown. The base of cabled models has a 1/2-inch

NPS integral internal conduit thread.

Environmental Raꢀng

Banner tested to NEMA 6P, IEC IP67

Applicaꢀon Note

Special Condiꢀons for Safe Use: Parts of the enclosure are non-conducꢀng and

may generate an igniꢀon-capable level of ESD. Cleaning of the equipment must

be done only with a damp cloth.

IEC IECEx FMG 14.0029X

ATEX FM12ATEX0094X

FM CoC 0003046293 (US)

FM CoC 0003046293C (CAN)

Design Standards

ATEX (European)

Canada

EN 60079-0, EN 60079-11 and EN 60079-26

CAN/CSA C22.2: No.0-M91, No.142-M1987, No.157-92, No.213-M1987, No.1010.1, E60079-0 and E60079-11

FM Class 3600, 3610, and 3810; ANSI/ISA 61010-1 (82.02.01), 60079-0 and 60079-11

IEC 60079-0, IEC 60079-11

United States

IECEx

Lexan is a registered trademark of General Electric Co.

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 38343 Rev. K

Q45AD9 NAMUR Series Sensor

Approvals

Q45AD9(a)(b),

Q459E(b)

a = Sensing mode D, DL, F, FP, FV, LV, LP, CV, CV4 or R.

b = Connecꢀon method Q or blank

ATEX (European)

II 1 G Ex ia IIC T5 Ta = -40°C to 70°C - 38343; Enꢀty

Enꢀty Parameters: U = 15 V dc, I = 60 mA, P = 225 mW, C = 0.3 μF, L = 0 mH.

Canadian

IS / I,II,III / 1 / ABCDEFG / T5 Ta = -40°C to 70°C - 38343; Enꢀty

I / 0 / Ex ia / IIC / T5 Ta = -40°C to 70° C - 38343; Enꢀty

(Non-incendive) NI / I / 2 / ABCD / T5 Ta = -40°C to 70°C

Enꢀty Parameters: V

= 15 V dc, I

= 60 mA, P = 225 mW, C = 0.3 μF, L = 0 mH

Max i i i

Max

United States

IS / I,II,III / 1 / ABCDEFG / T5 Ta = -40°C to 70°C - 38343; Enꢀty

I / 0 / AEx ia / IIC / T5 Ta = -40°C to 70°C - 38343; Enꢀty

(Non-incendive) NI / I / 2 / ABCD / T5 Ta = -40°C to 70°C

S / II,III / 2 / FG* / T5 Ta = -40°C to 70°C

*Class II and III, Division 2 applies only to model numbers ending in a Q suﬃx.

Enꢀty Parameters: V = 15 V dc, I

= 60 mA, P = 225 mW, C = 0.3 μF, L = 0 mH

Max

IECEx

Ex ia IIC T5 Ta= -40 °C to +70 °C - 35331; Enꢀty

Enꢀty Parameters: U = 15 V dc, I = 60 mA, C = 0.3 μF, L = 0 mH.

Performance Curves

Opposed

Excess Gain

Beam Paꢁern

1000

Q45AD9 E/R

Opposed Mode

Q45AD9 E/R

Opposed Mode

100

150 mm

6 in

100 mm

50 mm

4 in

2 in

50 mm

100 mm

150 mm

2 in

4 in

6 in

0.1 m

0.33 ft

1.0 m

3.3 ft

10 m

33 ft

100 m

330 ft

1.2 m

4 ft

2.4 m

8 ft

3.6 m

12 ft

4.8 m

16 ft

6 m

20 ft

DISTANCE

P/N 38343 Rev. K

www.bannerengineering.com - Tel: +1-763-544-3164

Q45AD9 NAMUR Series Sensor

Retroreꢂecꢀve Non-Polarized

Excess Gain Beam Paꢁern

Retroreꢂecꢀve Polarized

Excess Gain Beam Paꢁern

1000

Q45AD9LP

Q45AD9LV

Retroreflective Mode

Q45AD9LV

Retroreflective Mode

100

Q45AD9LP

Retroreflective

Mode

100

75 mm

3.0 in

75 mm

3.0 in

50 mm

25 mm

2.0 in

1.0 in

50 mm

25 mm

2.0 in

1.0 in

With BRT-3 Reflector

25 mm

50 mm

75 mm

1.0 in

2.0 in

3.0 in

25 mm

50 mm

75 mm

1.0 in

2.0 in

3.0 in

With BRT-3 Reflector

.01 m

.033 ft

.10 m

.33 ft

1.0 m

3.3 ft

10 m

33 ft

3 m

10 ft

6 m

20 ft

9 m

30 ft

12 m

40 ft

15 m

50 ft

.01 m

.033 ft

.10 m

.33 ft

1.0 m

3.3 ft

10 m

33 ft

1.5 m

5 ft

3 m

10 ft

4.5 m

15 ft

6 m

20 ft

7.5 m

25 ft

DISTANCE

Diﬀuse Short Range

Beam Paꢁern

Diﬀuse Long Range

Excess Gain

Beam Paꢁern

1000

Q45AD9DL

Diffuse Mode

Q45AD9D

Diffuse Mode

Q45AD9DL

Diffuse Mode

15 mm

0.6 in

100

Q45AD9D

Diffuse Mode

7.5 mm

0.3 in

10 mm

5 mm

0.4 in

0.2 in

5.0 mm

2.5 mm

0.2 in

0.1 in

5 mm

10 mm

15 mm

0.2 in

0.4 in

0.6 in

2.5 mm

5.0 mm

7.5 mm

0.1 in

0.2 in

0.3 in

1.0 mm

0.04 in

10 mm

0.4 in

100 mm

4.0 in

1000 mm

40 in

100 mm 200mm 300 mm 400 mm 500 mm

4.0 in 8.0 in 12.0 in 16.0 in 20.0 in

0.3 m

1 ft

0.6 m

2 ft

0.9 m

3 ft

1.2 m

4 ft

1.5 m

5 ft

0.01 m

0.033 ft

0.1 m

0.33 ft

1 m

3.3 ft

10 m

33 ft

DISTANCE

Convergent (CV and CVQ Models)

Excess Gain Beam Paꢁern

Convergent (CV4 and CV4Q Models)

Excess Gain Beam Paꢁern

1000

Q45AD9CV

Q45AD9CV4

Convergent Mode

Q45AD9CV4

100

Q45AD9CV

100

3.8 mm

0.15 in

3.8 mm

0.15 in

Convergent Mode

2.5 mm

1.2 mm

0.10 in

0.05 in

2.5 mm

1.2 mm

0.10 in

0.05 in

1.2 mm

2.5 mm

3.8 mm

0.05 in

0.10 in

0.15 in

1.2 mm

2.5 mm

3.8 mm

0.05 in

0.10 in

0.15 in

1 mm

.04 in

10 mm

.4 in

100 mm

4 in

1000 mm

40 in

38 mm

1.5 in

75 mm 113 mm 150 mm 190 mm

3.0 in 4.5 in 6.0 in 7.5 in

1 mm

.04 in

10 mm

.4 in

100 mm

4 in

1000 mm

40 in

38 mm

1.5 in

75 mm 113 mm 150 mm 190 mm

3.0 in 4.5 in 6.0 in 7.5 in

DISTANCE

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 38343 Rev. K

Q45AD9 NAMUR Series Sensor

Plasꢀc Fiber Opꢀc (Opposed Mode)

Excess Gain Beam Paꢁern

Plasꢀc Fiber Opꢀc (Diﬀuse Mode)

Excess Gain Beam Paꢁern

1000

100

1000

100

Q45AD9FP

Diffuse Mode

Q45AD9FP

Opposed Mode

Q45AD9FP

Diffuse Mode

Q45AD9FP

Opposed Mode

45 mm

1.8 in

2.4 mm

0.09 in

30 mm

15 mm

1.2 in

0.6 in

PBT46U Fiber

PIT46U Fibers

1.6 mm

0.8 mm

0.06 in

0.03 in

PBT46U Fiber

PIT46U Fibers

PIT26U Fibers

15 mm

30 mm

45 mm

0.6 in

1.2 in

1.8 in

0.8 mm

1.6 mm

2.4 mm

0.03 in

0.06 in

0.09 in

PIT26U Fibers

PBT26U Fiber

0.1 mm

0.004 in

1 mm

0.04 in

10 mm

0.4 in

100 mm

4 in

10 mm

0.4 in

20 mm

0.8 in

30 mm

1.2 in

40 mm 50 mm

1.6 in 2.0 in

1 mm

0.04 in

10 mm

0.4 in

100 mm

4.0 in

1000 mm

40 in

25 mm

1.0 in

50 mm

2.0 in

75 mm 100 mm 125 mm

3.0 in 4.0 in 5.0 in

DISTANCE

Glass Fiber Opꢀc, Infrared (Opposed Mode)

Excess Gain Beam Paꢁern

Glass Fiber Opꢀc, Infrared (Diﬀuse Mode)

Excess Gain Beam Paꢁern

1000

Q45AD9F

Diffuse Mode

Opposed Mode

IT13S Fibers

Q45AD9F

100

Q45AD9F

Diffuse Mode

37.5 mm

1.5 in

1.5 mm

0.06 in

25.0 mm

12.5 mm

1.0 in

0.5 in

IT23S fibers

1.0 mm

0.5 mm

0.04 in

0.02 in

IT23S Fibers

BT23S fiber

BT23S Fiber

BT13S Fiber

IT13S fibers

12.5 mm

25.0 mm

37.5 mm

0.5 in

1.0 in

1.5 in

0.5 mm

1.0 mm

1.5 mm

0.02 in

0.04 in

0.06 in

BT13S fiber

1.0 mm

0.04 in

10 mm

0.4 in

100 mm

4 in

1000 mm

40 in

1.0 mm

0.04 in

10 mm

0.4 in

100 mm

4 in

1000 mm

40 in

125 mm 250 mm 375 mm 500 mm 625 mm

5 in 10 in 15 in 20 in 25 in

12.5 mm 25.0 mm 37.5 mm 50.0 mm 62.5 mm

0.5 in 1.0 in 1.5 in 2.0 in 2.5 in

DISTANCE

Glass Fiber Opꢀc, Visible Red (Opposed Mode)

Excess Gain Beam Paꢁern

Glass Fiber Opꢀc, Visible Red (Diﬀuse Mode)

Excess Gain Beam Paꢁern

1000

Q45AD9FV

Opposed Mode

IT23S Fibers

Diffuse Mode

Q45AD9FV

Diffuse Mode

Q45AD9FV

Opposed Mode

100

3.0 mm

0.12 in

30 mm

1.2 in

100

2.0 mm

1.0 mm

0.08 in

0.04 in

20 mm

10 mm

0.8 in

0.4 in

IT23S Fibers

BT13S Fiber

1.0 mm

2.0 mm

3.0 mm

0.04 in

0.08 in

0.12 in

10 mm

20 mm

30 mm

0.4 in

0.8 in

1.2 in

IT13S Fibers

BT13S

Fiber

BT23S Fiber

1.0 mm

0.04 in

10 mm

0.4 in

100 mm

4 in

1000 mm

40 in

5 mm

0.2 in

10 mm

0.4 in

15 mm

0.6 in

20 mm 25 mm

0.8 in 1.0 in

100 mm 150 mm 200 mm 250 mm 300 mm

4 in 6 in 8 in 10 in 12 in

1 mm

0.04 in

10 mm

0.4 in

100 mm

4.0 in

1000 mm

40 in

DISTANCE

P/N 38343 Rev. K

www.bannerengineering.com - Tel: +1-763-544-3164

Q45AD9 NAMUR Series Sensor

Dimensions

NAMUR Series Opposed, Retro, and Diﬀuse Sensing Modes (Model Suﬃx E, R, D, DL, LP, and LV)

Cabled Models Quick-Disconnect 4-pin Euro-style Models

54.1 mm

(2.13")

44.5 mm

(1.75")

Lens Centerline

50.8 mm

(2.00")

69.0 mm

(2.72")

6.4 mm (0.25")

87.6 mm

(3.45")

4.5 mm (#10) Screw

Clearance (2)

7.1 mm

(0.28")

30.0 mm

(1.18")

Internal Thread

(1/2–14NPSM)

ø 6.1 (0.24")

2m (6.5') Cable

External thread (M30 x 1.5)

hex nut supplied

Euro- or Micro-style

QD Connector

15 mm (0.6")

Convergent Sensor Models (CV and CV4)

Glass Fiber Opꢀc Models (F and FV)

Plasꢀc Fiber Opꢀc Models (FP)

60.5 mm

(2.38")

61.7 mm

(2.43")

59.9 mm

(2.36")

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 38343 Rev. K

Q45AD9 NAMUR Series Sensor

Accessories

Quick-Disconnect (QD) Cables

4-Pin Threaded M12/Euro-Style Cordsets (for use with NAMUR sensors)

Model

Length

Style

Dimensions

Pinout (Female)

MQD9-406

MQD9-415

1.83 m (6 ꢁ)

4.57 m (15 ꢁ)

44 Typ.

Straight

M12 x 1

MQD9-430

9.14 m (30 ꢁ)

ø 14.5

MQD9-406RA

MQD9-415RA

1.83 m (6 ꢁ)

32 Typ.

[1.26"]

4.57 m (15 ꢁ)

30 Typ.

[1.18"]

1 = Brown

2 = Blue

Right-Angle

MQD9-430RA

9.14 m (30 ꢁ)

M12 x 1

ø 14.5 [0.57"]

Replacement Lenses

Replacement Lens Assemblies

Models

UC-45L

UC-45LP

UC-45D

UC-45F

UC-45FP

UC-45C

UC-45C4

Descripꢀon

Replacement lens for E, R, DL and LV models

Replacement lens for LP

Replacement lens for D

Replacement lens for F and FV

Replacement lens for FP

Replacement lens for CV

Replacement lens for CV4

Q45 Series lens assemblies are ﬁeld-replaceable.

Brackets

Mounꢀng Brackets

SMB30C

SMB30SC

•

Swivel bracket with 30 mm

•

30 mm split clamp, black PBT

bracket

Stainless steel mounꢀng

hardware included

Mounꢀng hole for 30 mm

mounꢀng hole for sensor

•

Black reinforced thermoplasꢀc

polyester

Stainless steel mounꢀng and

swivel locking hardware

included

sensor

Hole center spacing: A=ø 45

Hole size: B=ø 27.2

Hole center spacing: A=ø 50.8

Hole size: A=ø 7.0, B=ø 30.0

P/N 38343 Rev. K

www.bannerengineering.com - Tel: +1-763-544-3164

Q45AD9 NAMUR Series Sensor

Mounꢀng Brackets

SMB30MM

SMB30UR

•

12-ga. stainless steel bracket

•

2-piece universal swivel bracket

for limit-switch style sensors

300 series stainless steel

Stainless steel swivel locking

hardware included

with curved mounꢀng slots for

versaꢀle orientaꢀon

•

Clearance for M6 (¼ in)

hardware

Mounꢀng hole for 30 mm

sensor

Hole center spacing: A to B=31.8, B to C=19.0, A to C=50.8, D=50.8

Hole size: C=6.9x32, D=73.0x6.9

Hole center spacing: A = 51, A to B = 25.4

Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1

Repairs and Translaꢀons

Obtain assistance with product repairs by contacꢀng your local Banner Engineering Corp distributor or by calling Banner directly at (763)

544-3164. Access literature translated into your naꢀve language on the Banner website at www.bannerengineering.com or contact

Banner directly at (763) 544-3164.

Para reparaciones de productos, por favor contacte a su distribuidor local de Banner Engineering o llame a Banner directamente al (763)

544-3164. Vea la literatura traducida en su idioma en el siꢀo web Banner en www.bannerengineering.com o comuníquese con Banner

directamente al (763) 544-3164.

Pour vous aider lors de la réparaꢀon de produits, contactez votre distributeur Banner local our appelez directement Banner au (763)

544-3164. La documentaꢀon traduite dans votre langue est disponible sur le site internet de Banner www.bannerengineering.com ou

contactez directement Banner au (763) 544-3164.

Banner Engineering Corp. Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or

replace, free of charge, any product of its manufacture which, at the ꢀme it is returned to the factory, is found to have been defecꢀve during the warranty period. This warranty does not cover

damage or liability for misuse, abuse, or the improper applicaꢀon or installaꢀon of the Banner product.

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.

This Warranty is exclusive and limited to repair or, at the discreꢀon of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY

OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT

DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligaꢀons or liabiliꢀes relaꢀng to any product previously

manufactured by Banner Engineering Corp. Any misuse, abuse, or improper applicaꢀon or installaꢀon of this product or use of the product for personal protecꢀon applicaꢀons when the

product is idenꢀﬁed as not intended for such purposes will void the product warranty. Any modiﬁcaꢀons to this product without prior express approval by Banner Engineering Corp will void the

product warranꢀes. All speciﬁcaꢀons published in this document are subject to change; Banner reserves the right to modify product speciﬁcaꢀons or update documentaꢀon at any ꢀme.

Speciﬁcaꢀons and product informaꢀon in English supersede that which is provided in any other language. For the most recent version of any documentaꢀon, refer to:

www.bannerengineering.com.

Q45AD9CVQ [BANNER]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E