Q45XDN2CVQ6 [BANNER]
Intelligentâ Photoelectric Sensors for use on DeviceNet Bus Networks;
| 型号： | Q45XDN2CVQ6 |
| 厂家： | 
Banner Engineering |
| 描述： | Intelligentâ Photoelectric Sensors for use on DeviceNet Bus Networks |
| 文件： | 总8页 (文件大小：640K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Q45XDN
“Intelligent” Photoelectric Sensors for use on DeviceNet™ Bus Networks
Features
• Easy “smart sensor” interfacing to DeviceNet bus networks
• Integral Euro-style (M12) quick-disconnect connector for DeviceNet compatible cable
• Impressive optical performance in opposed, diffuse, retroreflective, convergent or
fiber optic sensing modes
• Highly visible Power and Received Signal Strength indicator LEDs
• Tough mechanical design
Description
Q45XDN Series sensors are designed specifically for use on DeviceNet-bus
networks. These are “smart” sensors which can be wired to a DeviceNet bus using
a “dumb” tee.
Q45XDN1 models support the Bit Strobe Connection, which responds to a master’s
request. Q45XDN2 models support the Change of State Connection, which responds
to a slave’s change of state. All models support the Explicit Message Connection,
which is required to Set and Get sensor Attributes.
™
Q45XDN Series sensors feature two highly-visible sensor status indicator LEDs for
power and received signal strength. The Signal indicator incorporates Banner’s
patented† Alignment Indicating Device (AID™) circuitry which pulses the indicator at a
rate which is proportional to the received light signal strength. A slow flash rate alerts
personnel to a marginal signal due to sensor misalignment or dirt on the lenses.
Q45XDN Series photoelectric sensors have impressive optical performance (see
excess gain curves on pp. 2 - 4). All models boast o-ring sealing which exceeds the
NEMA 6P (IP67) rating. They are extremely rugged, with PBT polyester housings and
molded acrylic lenses. They are equipped with a 12 mm Euro-style quick-disconnect
connector which accepts DeviceNet-compatible cable (see Hookup Information).
†U.S. Patent #4356393
WARNING . . .
Not To Be Used for Personnel Protection
Never use this product as a sensing device for personnel protection. Doing so could lead to serious injury or death.
!
This product does NOT include the self-checking redundant circuitry necessary to allow its use in personnel safety
applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your
current Banner Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection.
Printed in USA
05/03
P/N 46655 rev. C
Q45XDN
™
Infrared, 880 nm
Opposed-Mode Emitter (E) and Receiver (R) Models
Supply
Voltage
I/O
Support
Beam Pattern
Effective Beam: 13 mm
Models
Focus
Cable
Excess Gain
1000
Q45E/R
Opposed Mode
Emitter Only
Bit Strobe
Q45XDN1EQ6
Q45E/R
Opposed Mode
E
X
C
E
S
S
1.5 m
60 in
1.0 m
0.5 m
0
40 in
20 in
0
100
10
0.5 m
1.0 m
1.5 m
20 in
40 in
60 in
60 m
(200')
Q45XDN1RQ6
Q45XDN2RQ6
5-pin Euro QD
11-25V dc
G
A
I
N
0
12 m
40 ft
24 m
80 ft
36 m
120 ft
48 m
160 ft
60 m
200 ft
1
0.1 m
0.33 ft
1.0 m
3.3 ft
10 m
33 ft
100 m
330 ft
DISTANCE
Change of
State
DISTANCE
P
Visible Red, 680 nm
Retroreflective Mode Models
Supply
Voltage
I/O
Support
Models
Focus
Cable
Excess Gain
Beam Pattern
1000
Q45LV
Non-Polarized
Q45LV
E
X
C
E
S
S
75 mm
3.0 in
Retroreflective Mode
50 mm
25 mm
0
2.0 in
1.0 in
0
Retroreflective Mode
100
10
Bit Strobe
Q45XDN1LVQ6
Q45XDN2LVQ6
With BRT-3 Reflector
80 mm to
9 m
25 mm
50 mm
75 mm
1.0 in
2.0 in
3.0 in
G
A
I
5-pin Euro QD
Polarized
11-25V dc
With BRT-3 Reflector
N
(3" to 30')
Change of
State
0
3 m
10 ft
6 m
20 ft
9 m
30 ft
12 m
40 ft
15 m
50 ft
1
.01 m
.033 ft
.10 m
.33 ft
1.0 m
3.3 ft
10 m
33 ft
DISTANCE
DISTANCE
1000
Q45LP
E
X
C
E
S
S
Q45LP
75 mm
3.0 in
Retroreflective
Mode
50 mm
25 mm
0
2.0 in
1.0 in
0
Retroreflective Mode
100
10
Bit Strobe
Q45XDN1LPQ6
Q45XDN2LPQ6
With BRT-3 Reflector
150 mm to
6 m
With BRT-3 Reflector
25 mm
50 mm
75 mm
1.0 in
2.0 in
3.0 in
G
A
I
5-pin Euro QD
11-25V dc
(6" to 20')
N
Change of
State
0
1.5 m
5 ft
3 m
10 ft
4.5 m
15 ft
6 m
20 ft
7.5 m
25 ft
1
.01 m
.033 ft
.10 m
.33 ft
1.0 m
3.3 ft
10 m
33 ft
DISTANCE
DISTANCE
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
2
P/N 46655 rev. C
Q45XDN
™
Infrared, 880 nm
Diffuse Mode Models
Supply
Voltage
I/O
Support
Excess Gain
Beam Pattern
Models
Focus
Cable
Performance based on 90% reflectance white test card
1000
100
10
Short-Range Diffuse
Q45D
E
X
C
E
S
S
15 mm
0.6 in
Diffuse Mode
Q45D
10 mm
0.4 in
0.2 in
0
Diffuse Mode
5 mm
0
Bit Strobe
Q45XDN1DQ6
Q45XDN2DQ6
5 mm
10 mm
15 mm
0.2 in
0.4 in
0.6 in
G
A
I
450 mm
(18")
5-pin Euro QD 11-25V dc
N
Change of
State
0
100 mm 200mm 300 mm 400 mm 500 mm
1
4.0 in
8.0 in 12.0 in 16.0 in 20.0 in
1.0 mm
0.04 in
10 mm
0.4 in
100 mm
4.0 in
1000 mm
40 in
DISTANCE
DISTANCE
1000
Long-Range Diffuse
Q45DL
E
X
C
E
S
S
75 mm
3.0 in
Q45DL
Diffuse Mode
Diffuse Mode
100
10
50 mm
25 mm
0
2.0 in
1.0 in
0
Bit Strobe
Q45XDN1DLQ6
Q45XDN2DLQ6
25 mm
50 mm
75 mm
1.0 in
2.0 in
3.0 in
G
A
I
1.8 m
(6')
5-pin Euro QD 11-25V dc
N
Change of
State
1
0
0.6 m
2 ft
1.2 m
4 ft
1.8 m
6 ft
2.4 m
8 ft
3.0 m
10 ft
.01 m
.033 ft
.10 m
.33 ft
1.0 m
3.3 ft
10 m
33 ft
DISTANCE
DISTANCE
Visible Red, 680 nm
Convergent Mode Models
Supply
Voltage
I/O
Message
Excess Gain
Beam Pattern
Models
Focus
Cable
Performance based on 90% reflectance white test card
1000
100
10
Q45CV
E
X
C
E
S
S
Q45CV
3.8 mm
Convergent Mode
0.15 in
Bit Strobe
Q45XDN1CVQ6
Convergent Mode
2.5 mm
1.2 mm
0
0.10 in
0.05 in
0
38 mm
(1.5 in)
5-pin Euro QD 11-25V dc
1.2 mm
2.5 mm
3.8 mm
0.05 in
0.10 in
0.15 in
G
A
I
Change of
State
N
Q45XDN2CVQ6
Q45XDN1CV4Q6
Q45XDN2CV4Q6
1
0
38 mm 75 mm 113 mm 150 mm 190 mm
1.5 in 3.0 in 4.5 in 6.0 in 7.5 in
1 mm
.04 in
10 mm
.4 in
100 mm
4 in
1000 mm
40 in
DISTANCE
DISTANCE
1000
Q45CV4
Convergent Mode
E
X
C
E
S
S
Q45CV4
Convergent Mode
3.8 mm
0.15 in
Bit Strobe
100
10
2.5 mm
1.2 mm
0
0.10 in
0.05 in
0
100 mm
(4 in)
5-pin Euro QD 11-25V dc
1.2 mm
2.5 mm
3.8 mm
0.05 in
0.10 in
0.15 in
G
A
I
Change of
State
N
1
0
38 mm 75 mm 113 mm 150 mm 190 mm
1.5 in 3.0 in 4.5 in 6.0 in 7.5 in
1 mm
.04 in
10 mm
.4 in
100 mm
4 in
1000 mm
40 in
DISTANCE
DISTANCE
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
P/N 46655 rev. C
3
Q45XDN
™
Infrared, 880 nm
Glass Fiber Optic Models
Supply
Voltage
I/O
Message
Excess Gain
Diffuse mode performance based on 90% reflectance white test card
Beam Pattern
Models
Focus
Cable
1000
100
10
Q45F
E
X
C
E
S
S
Q45F
150 mm
6.0 in
Opposed Mode
IT23S fibers
Opposed Mode
100 mm
50 mm
0
4.0 in
2.0 in
0
IT23S Fibers
IT13S Fibers
Bit Strobe
50 mm
100 mm
150 mm
2.0 in
4.0 in
6.0 in
Q45XDN1FQ6
G
A
I
IT13S fibers
Range
varies by
sensing
N
0
0.4 m
15 in
0.8 m
30 in
1.2 m
45 in
1.6 m
60 in
2.0 m
75 in
1
0.01 m
0.03 ft
0.1 m
0.33 ft
1.0 m
3.3 ft
10 m
33 ft
DISTANCE
DISTANCE
mode and 5-pin Euro QD 11-25V dc
1000
fiber
optics
used
Q45F
E
X
C
E
S
S
Q45F
Diffuse Mode
3.8 mm
0.15 in
Diffuse Mode
2.5 mm
1.3 mm
0
0.10 in
0.05 in
0
100
10
BT13S Fiber
BT23S Fiber
Change of
State
BT23S Fiber
1.3 mm
2.5 mm
3.8 mm
0.05 in
0.10 in
0.15 in
Q45XDN2FQ6
G
A
I
BT13S Fiber
N
1
0
25 mm 50 mm 75 mm 100 mm 125 mm
1 in 2 in 3 in 4 in 5 in
1 mm
0.04 in
10 mm
0.4 in
100 mm
4.0 in
1000 mm
40 in
DISTANCE
DISTANCE
Visible Red, 660 nm
Plastic Fiber Optic Models
Supply
Voltage
I/O
Message
Excess Gain
Diffuse mode performance based on 90% reflectance white test card
Beam Pattern
Models
Focus
Cable
1000
Q45FP
E
X
C
E
S
S
Q45FP
45 mm
1.8 in
Opposed Mode
Opposed Mode
30 mm
15 mm
0
1.2 in
0.6 in
0
PIT46U Fibers
100
10
PIT26U Fibers
PIT46U Fibers
Bit Strobe
Q45XDN1FPQ6
15 mm
30 mm
45 mm
0.6 in
1.2 in
1.8 in
G
A
I
Range
varies
by
sensing
mode
and
fiber
optics
used
PIT26U Fibers
N
0
25 mm 50 mm 75 mm 100 mm 125 mm
1
1.0 in
2.0 in
3.0 in
4.0 in
5.0 in
1 mm
0.04 in
10 mm
0.4 in
100 mm
4.0 in
1000 mm
40 in
DISTANCE
DISTANCE
5-pin Euro QD
11-25V dc
1000
Q45FP
E
X
C
E
S
S
Q45FP
18 mm
0.75 in
Diffuse Mode
PBT46U Fiber
Diffuse Mode
12 mm
6 mm
0
0.50 in
0.25 in
0
100
10
PBT46U Fiber
Change of
State
Q45XDN2FPQ6
6 mm
12 mm
18 mm
0.25 in
0.50 in
0.75 in
G
A
I
N
PBT26U Fiber
1
0
10 mm 20 mm 30 mm 40 mm 50 mm
0.4 in 0.8 in 1.2 in 1.6 in 2.0 in
0.1 mm
0.004 in
1 mm
0.04 in
10 mm
0.4 in
100 mm
4 in
DISTANCE
DISTANCE
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
4
P/N 46655 rev. C
Q45XDN
™
Specifications
Supply Voltage and Current
Supply Protection Circuitry
The sensor is powered by the bus network (11 to 25V dc @60 mA)
Protected against reverse polarity, transient voltages, and loss of ground.
(none of these conditions will harm the sensor or interrupt communication on the network)
Response Time
Adjustments
2 milliseconds; Total response time will also include the response time of the network
Multi-turn SENSITIVITY control on top of the sensor (beneath a transparent o-ring sealed cover) allows
precise sensitivity setting (turn clockwise to increase gain); Internal switch must be in Light Operate (L/O)
position, which is the factory setting
Indicators
On the sensor: Green and Red; visible through the transparent sensor top cover
Green LED lights for dc power ON
Red LED is Banner’s patented Alignment Indicating Device (AID™, U.S. patent #4356393) which lights
whenever the sensor “sees” a light condition and superimposes a pulse rate which is proportional to
the strength of the received light signal (the stronger the signal, the faster the pulse rate)
On the 45DN Bus Card: Green and Red; visible through the transparent sensor top cover
A bi-color LED indicates the status of the network.
Green
Steady
Flashing
Steady
Sensor on line, connected to master
Sensor on line, address + baud rate are ok
Critical network fault or duplicate node address detected; wrong baud rate
Minor or connection time-out fault
Red
Flashing
Sensor Configuration
The following features of the Q45XDN Series Sensors are programmable via the network with a configuration
tool*:
Feature
Network Address
Baud Rate
Range
0-63 (default = 63)
125K, 250K, 500K (default = 125K)
Light Operate or Dark Operate (default = Light Operate)
Operate Mode*
All Q45XDN models support:
Explicit Message Connection: Required to Set and Get sensor Attributes
Q45XDN1 supports the following connection type:
Bit Strobe Connection: Responds to a master’s request.
Q45XDN2 supports the following connection type:
Change of State Connection (COS): Responds to a slave’s change of state.
I/O Response is with the following 8-bit word of data:
Bit: 0:
0
1
0
1
Output is OFF
Output is ON
Alarm output is OFF
Alarm output is ON
Bit 1:
Bits 2-7 Not Used: Always 0
*NOTES: Configuration may be simplified through use of an Electronic Data Sheet (Banner model EDS
40223).
The Light/Dark Operate switch in the Q45 sensor must be set to the Light Operate position (the
factory setting).
Construction
Molded PBT polyester thermoplastic polyester housing; molded acrylic lenses; stainless steel hardware. O-ring
sealed transparent polycarbonate top cover.
Environmental Rating
Connections
IEC IP67; NEMA 6P
Euro-style DeviceNet™-compatible quick-disconnect cables
Operating Temperature
-25° to +70°C (-13° to +158°F); Maximum relative humidity 95% (non-condensing)
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
P/N 46655 rev. C
5
Q45XDN
™
Dimensions
Overall Sensor Depth
Suffix
Transparent Cover (Gasketed)
Depth
View: Sensing Status (Red)
(all models except emitters)
Power Suppy (Green)
E (emitter),
D (short-range diffuse),
DL (long-range diffuse),
LV (retroreflective), and
R (receiver)
Raise to Access:
54.6 mm
(2.15")
Sensitivity (Gain) Adjustment
See table
at left
44.5 mm
(1.75")
61.5 mm
(2.42")
56.4 mm
(2.30")
60.5 mm
(2.38")
CV and CV4 (convergent)
LP (polarized retroreflective)
F (glass fiber optic)
Lens
Centerline
50.8 mm
(2.00")
69.0 mm
(2.72")
59.8 mm
(2.35")
FP (plastic fiber optic)
6.4 mm
(0.25")
87.6 mm
(3.45")
5 mm (#10) Screw
Clearance (2)
7.1 mm
(0.28")
30.0 mm
(1.18")
A 30 mm jam nut is
supplied for mounting
4-Pin 12mm Euro-style
Quick Disconnect Connector
External Thread
M30 x 1.5
Hookups
Q45X Male Connector
Pin
Wire Color
Function
1
2
3
4
5
Shield
Male Pinout
Red
BUS power (+V)
BUS power (-V)
Communications +
Communications -
4
Black
White
Blue
1
2
3
5
The Q45XDN sensor requires DeviceNet-compatible quick-disconnect cable which is available from various manufacturers, such as
interlinkBT.
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
6
P/N 46655 rev. C
Q45XDN
™
Mounting Brackets
• 12-gauge, stainless steel, right angle
• 30 mm split clamp bracket
• Black reinforced thermoplastic polyester
• Includes stainless steel mounting hardware
mounting bracket with a curved mounting
slot for versatility and orientation
SMB30S
SMB30C
• Clearance for M6 (1/4") hardware
56.0 mm
13 mm
(2.20")
Not Shown:
(2) M5 x 0.8 x 60 mm
screws are supplied for
clamping bracket together
63.5 mm
(2.50")
12.2 mm
(0.48")
(0.5")
63.0 mm
(2.48")
82.5 mm
(3.25")
31.5 mm
(1.24")
43.2 mm
(1.70")
13.5 mm (0.53")
Nut Plate
2.5 mm
25.4 mm
(1.00")
45.0 mm
(1.77")
50.8 mm
(2.00")
(0.10")
M5 x 0.8
x 80 mm
Screw (2)
M5 x 0.8
x 30 mm
Screw (2)
• 30 mm, 12-gauge, stainless steel bracket
with curved mounting slots for versatility
and orientation
SMB30MM
• Clearance for M6 (1/4") hardware
25.4 mm
(1.00")
ø30.1 mm
(1.19")
35.1 mm
(1.38")
7.1 mm
.28 x 90° (2 Slots)
ø 6.4 mm
(0.25" dia.)
57.2 mm
(2.25")
25.4 mm
(1.00")
R 25.4 mm
(1.00")
57.2 mm
(2.25")
35.1 mm
(1.38")
69.9 mm
(2.75")
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
P/N 46655 rev. C
7
Q45XDN
™
WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or
replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period.
This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty
either expressed or implied.
P/N 46655 rev. C
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明