QS18E [BANNER]

WORLD-BEAMÂ® QS18E Series;


型号：	QS18E
厂家：	Banner Engineering
描述：	WORLD-BEAMÂ® QS18E Series
文件：	总11页 (文件大小：860K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

WORLD-BEAM QS18E Series

Datasheet

•

Easy-to-use Expert-style Staꢀc and Dynamic TEACH opꢀons, plus Window, Light, and Dark

SET, via push buꢁon or remote input

•

Smart power-control algorithm to maximize performance in low-contrast applicaꢀons

Easy push-buꢁon or remote sensor setup opꢀons:

◦

Dark-Operate/Light-Operate select

Selectable 30 ms output OFF-delay

•

Less than 1 millisecond output response for excellent sensing repeatability

Tough ABS housing is rated IEC IP67; NEMA 6

Bright LED operaꢀng status indicators are visible from 360°

Discrete PNP or NPN output, depending on model

Mulꢀple connecꢀon opꢀons available (see Models)

Compact housing, easy barrel-mount (some models) or side-mount installaꢀon

WARNING: Not To Be Used for Personnel Protecꢀon

Never use this device as a sensing device for personnel protecꢀon. Doing so could lead to serious injury or death. This device

does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applicaꢀons. A sensor failure

or malfuncꢀon can cause either an energized or de-energized sensor output condiꢀon.

Model

Sensing Mode

Range

Output

Model

Sensing Mode

Range

Output

QS18EN6LP

660 nm Visible Red

NPN

QS18EN6CV15

660 nm Visible Red

NPN

3.5 m (12 ꢂ)

16 mm (0.65

in)

QS18EP6LP

PNP

QS18EP6CV15

PNP

POLAR RETRO

CONVERGENT

QS18EN6D

QS18EP6D

QS18EN6DB

NPN

PNP

NPN

QS18EN6CV45

QS18EP6CV45

QS18EN6FP

NPN

PNP

NPN

800 mm (31.5

in)

43 mm (1.7

in)

660 nm Visible Red

Varies by

mode and

ﬁber opꢀcs

used

940 nm Infrared

500 mm (19.7

in)

QS18EP6DB

QS18EN6W

QS18EP6W

PNP

NPN

PNP

QS18EP6FP

QS18EN6DV

QS18EP6DV

PNP

NPN

PNP

PLASTIC FIBER

DIFFUSE

660 nm Visible Red

300 mm (11.8

in)

600 mm

(23.6 in)

DIFFUSE

The standard 2 m (6.5 ꢂ) cable models are listed. To order the 9 m (30 ꢂ) cable models, add the suﬃx "W/30" to the cabled model number. For example, QS18EN6FP W/30. Models with a

quick disconnect (QD) connector require a maꢀng cable.

To order a model with a 4-pin QD 150 mm (6 in) Euro-style pigtail, add suﬃx “Q5” (for example, QS18EN6FPQ5).

To order a model with a 4-pin 150 mm (6 in) Pico-style pigtail, add suﬃx “Q” (for example, QS18EN6FPQ).

To order a model with a 4-pin Integral Euro-style QD, add suﬃx “Q8” (for example, QS18EN6FPQ8).

To order a model with a 4-pin Integral Pico-style QD, add suﬃx “Q7” (for example, QS18EN6FPQ7).

Speciﬁed using BRT-84 reﬂector (sold separately)

Original Document

136564 Rev. E

14 March 2017

136564

WORLD-BEAM QS18E Series

Overview of QS18E Expert Series Sensors

The QS18E Expert Sensors family of sensors provides high-performance sensing in a compact package.

The sensors feature a discrete output (NPN or PNP, depending on model), two bright LEDs for easy

status monitoring during conﬁguraꢀon and operaꢀon, mulꢀple conﬁguraꢀon opꢀons, remote

conﬁguraꢀon, and security lockout opꢀons.

1. Amber output LED

2. Green power indicator LED

3. Receiver port

4. Emiꢁer port

5. Conﬁguraꢀon buꢁon

Indicators (Two LEDs: One Green, One Amber)

Sensor Condiꢀon (Run Mode)

Output OFF

Green LED

Amber LED

OFF

Output ON

Output ON, marginal signal

Output Short Circuit

Flashing

OFF

Flashing

Figure 1. Sensor features

Wiring Diagrams

NPN (Sinking) Outputs

PNP (Sourcing) Outputs

10–30 V dc

10-30V dc

Load

Remote

Programming

(N.O.)

Programming

(N.O.)

Cabled wiring diagrams are shown. Quick disconnect (QD) wiring diagrams are funcꢀonally idenꢀcal.

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 136564 Rev. E

WORLD-BEAM QS18E Series

Sensor Conꢁguraꢀon

Conﬁgure the sensor using any of ﬁve TEACH or Set opꢀons (by push buꢁon or the remote wire) to

deﬁne the sensing limits. Use a Setup procedure to enable a 30 ms OFF-delay or to change the Light-/

Dark-Operate seꢃng (see Sensor Setup on page 3). Sensing limit conﬁguraꢀon opꢀons include:

•

Staꢀc TEACH: one switching threshold, determined by two taught condiꢀons

Dynamic (on-the-ﬂy) TEACH: one switching threshold, determined by mulꢀple sampled

condiꢀons

•

Light Set and Dark Set: one switching threshold, oﬀset from a single sensing condiꢀon (the

“dark” condiꢀon or the “light” condiꢀon; see Figure)

Window Set: a sensing window, centered around a single sensing condiꢀon

The sensor’s output is disabled during all TEACH and Set procedures, and is enabled upon return to Run

mode.

Following any TEACH or Set procedure other than Staꢀc TEACH, the Output ON condiꢀon (Light- or

Dark-Operate seꢃng) remains as it was last conﬁgured. To change that seꢃng or the OFF-delay seꢃng,

see Sensor Setup on page 3.

Figure 2. Dark Sensing Condiꢀon

Remote Conꢁguraꢀon

Use the remote funcꢀon to conﬁgure the sensor remotely or to disable the push buꢁon for security. Connect the white wire of the sensor to ground (0V

dc), through a remote programming switch. Pulse the remote line according to the diagrams in the conﬁguraꢀon procedures. The length of the individual

programming pulses is equal to the value T: 0.04 seconds ≤ T ≤ 0.8 seconds

Push Buꢂon Enable/Disable

The remote input may be used to disable the sensor push buꢁon to prevent unauthorized adjustment. Connect the white wire of the sensor as described

above to perform the procedure below to either enable or disable the feature.

Push Buꢂon Enable/Disable

Push Buꢂon ( 0.04 seconds ≤ "Click" ≤

Remote Line ( 0.04 seconds ≤ T ≤ 0.8 seconds)

Result

0.8 seconds)

Not available

From Run mode, four-pulse the remote line.

Sensor toggles between enable/disable seꢃngs and returns to RUN

mode.

Power LED: Flashes 3x, then ON Green

Output LED: OFF, then ON or OFF, depending on output state

Returning to RUN Mode without Saving Seꢃngs

Exit Staꢀc TEACH and Set modes aꢂer the automaꢀc 60-second ꢀme-out or by manually exiꢀng the process. To manual exit, press and hold the push

buꢁon (or hold the remote line low) for 2 seconds. The sensor returns to Run mode without saving any new seꢃngs.

Sensor Setup

Access setup funcꢀons directly from Run mode using the following procedures.

30 ms OFF-Delay (Pulse Stretcher) Enable/Disable

Push Buꢂon (0.04 seconds ≤ “Click” ≤ 0.8

seconds)

Remote Line (0.04 seconds ≤ T ≤ 0.8 seconds)

Results

From Run mode, six-click the push buꢁon. From Run mode, six-pulse remote line.

Sensor toggles between enable/disable seꢃngs and

returns to Run mode.

Power LED: Flashes 3x, then ON Green

Output LED: Enabled – ON,

Disabled – OFF,

Then ON or OFF, depending on output state

Iniꢀal output LED condiꢀon is simultaneous with Power LED 3-ﬂash

Iniꢀal Output LED condiꢀon is simultaneous with Power LED 3-ﬂash.

P/N 136564 Rev. E

www.bannerengineering.com - Tel: +1-763-544-3164

WORLD-BEAM QS18E Series

Light-Operate/Dark-Operate Select

Push Buꢂon (0.04 seconds ≤ “Click” ≤ 0.8

seconds)

Remote Line (0.04 seconds ≤ T ≤ 0.8 seconds)

Results

From Run mode, seven-click the push

buꢁon.

From Run mode, seven-pulse remote line.

Sensor toggles between Light-/Dark-Operate seꢃngs

and returns to Run mode.

Power LED: Flashes 3x, then ON Green

Output LED: Light Operate – ON,

Dark Operate – OFF,

Then ON or OFF, depending on output state

Staꢀc TEACH

•

Staꢀc TEACH locates a single switching threshold (switchpoint) at

the opꢀmal locaꢀon between the two taught condiꢀons, with the

Output ON condiꢀon on one side, and the Output OFF condiꢀon

on the other.

2nd Taught

Condition

1st Taught

Condition

Sensor positions

threshold between

presented conditions

•

During Staꢀc TEACH, the ﬁrst condiꢀon taught is the ON

condiꢀon. Output ON and OFF condiꢀons may be reversed by

switching the TEACH order or by changing the Light-/Dark-

Operate seꢃng in setup mode (see Sensor Setup on page 3).

Staꢀc TEACH is recommended for applicaꢀons where two

condiꢀons can be presented individually.

Output OFF

Output ON

Darkest

(no signal)

Most Light

(saturated

signal)

Figure 3. Staꢀc TEACH (Light Operate shown)

1. Access the Staꢀc TEACH Mode.

Method

Acꢀon

Result

The sensor waits for the ﬁrst sensing condiꢀon.

Push Buꢂon

Remote Line

Press and hold the push buꢁon 2 to 4 seconds.

Power LED Indicator: OFF

Output LED Indicator: Slow ﬂash (1Hz)

No acꢀon required; the sensor is ready for the ﬁrst sensing condiꢀon.

2. Teach the ﬁrst sensing condiꢀon.

Method

Acꢀon

Result

Present the ﬁrst (ON) sensing condiꢀon, then click the

push buꢁon.

Push Buꢂon

Power LED Indicator: OFF

Output LED Indicator: Double-ﬂash

Present the ﬁrst sensing condiꢀon, then single-pulse the

remote line.

Remote Line

3. Teach the second sensing condiꢀon.

Method

Acꢀon

Result

TEACH Accepted

Present the second (OFF) sensing condiꢀon, then click the

push buꢁon.

Push Buꢂon

Power LED Indicator: Flashes 3 ꢀmes, then

solid green

Output LED Indicator: OFF

The sensor returns to Run mode with the new

seꢃngs.

TEACH Not Accepted

Power LED Indicator: OFF

Output LED Indicator: Slow ﬂash (1 Hz)

Present the second sensing condiꢀon, then single-pulse

the remote line.

Remote Line

The sensor returns to the wait state, ready for

the ﬁrst sensing condiꢀon.

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 136564 Rev. E

WORLD-BEAM QS18E Series

Dynamic TEACH

•

Dynamic TEACH sets a single switching threshold (switchpoint).

Darkest Presented

Condition

Lightest Presented

Condition

Dynamic TEACH is used to teach during actual sensing condiꢀons,

taking mulꢀple samples of the light and dark condiꢀons and

automaꢀcally seꢃng the threshold at the opꢀmum level.

The Output ON state (Light- or Dark-Operate seꢃng) remains as it

was last conﬁgured. To change the Light-/Dark-Operate seꢃng,

see Sensor Setup on page 3.

Sensor positions

threshold between

•

presented conditions

Dynamic TEACH is recommended for applicaꢀons where a

machine or process may not be stopped for teaching.

Output OFF

Output ON

Darkest

(no signal)

Most Light

(saturated

signal)

Figure 4. Dynamic TEACH (Light Operate shown)

1. Access the Dynamic TEACH mode.

Method

Acꢀon

Result

Push Buꢂon

Press and hold the push buꢁon for longer than 4 seconds.

Power LED Indicator: OFF

Output LED Indicator: Quick ﬂash (2 Hz)

Hold the remote line low (to ground) for longer than 2

seconds.

2 seconds

Remote Line

2. Teach the sensing condiꢀon.

Method

Acꢀon

Result

Conꢀnue to hold the push buꢁon and present the Output

ON and OFF condiꢀons mulꢀple ꢀmes.

Push Buꢂon

Power LED Indicator: OFF

Output LED Indicator: Quick ﬂash (2 Hz)

Conꢀnue to hold the remote line low (to ground) and

present the Output ON and OFF condiꢀons mulꢀple

ꢀmes.

Remote Line

3. Return to Run mode.

Method

Acꢀon

Result

TEACH Accepted

Push Buꢂon

Release the push buꢁon.

Power LED Indicator: Flashes 3 ꢀmes, then

solid green

Output LED Indicator: OFF , then ON or OFF

depending on the output state

The sensor returns to Run mode with the new

seꢃngs.

TEACH Not Accepted

Remote Line

Release the remote line/switch.

Power LED Indicator: Flashes 3 ꢀmes, then

solid green

Output LED Indicator: ON , then ON or OFF

depending on the output state

The sensor returns to Run mode without

changing seꢃngs.

The iniꢀal output LED indicator condiꢀon is simultaneous with the power LED indicator 3-ﬂash

P/N 136564 Rev. E

www.bannerengineering.com - Tel: +1-763-544-3164

WORLD-BEAM QS18E Series

Light Set

•

Light Set sets a threshold approximately 12.5% below the

presented sensing condiꢀon.

Any condiꢀon darker than the threshold causes the output to

change state.

In Light-Operate mode, the presented condiꢀon is the Output ON

condiꢀon. In Dark-Operate mode, the presented condiꢀon is the

Output OFF condiꢀon. To change the Light-/Dark-Operate seꢃng,

see Sensor Setup on page 3.

Sensor positions

threshold ≈12.5% below

the presented condition

Output OFF

Output ON

•

Light Set is recommended for applicaꢀons where only one

condiꢀon is known, for example a stable light background with

varying darker targets, or in retroreﬂecꢀve applicaꢀons.

Darkest

(no signal)

Single

Presented

Condition

Most Light

(saturated

signal)

Figure 5. Light Set (Light Operate shown)

1. Access the Light Set mode.

Method

Acꢀon

Result

The sensor waits for the sensing condiꢀon.

Push Buꢂon

Press and hold the push buꢁon 2 to 4 seconds.

Power LED Indicator: OFF

Output LED Indicator: Slow ﬂash (1 Hz)

The sensor waits for the sensing condiꢀon.

Remote Line

Single-pulse the remote line.

Power LED Indicator: OFF

Output LED Indicator: Double-ﬂash

2. Set the sensing condiꢀon.

Method

Acꢀon

Result

TEACH Accepted

Present the sensing condiꢀon, then four-click the push

buꢁon.

Push Buꢂon

Power LED Indicator: Flashes 3 ꢀmes, then

solid green

Output LED Indicator: OFF , then ON or OFF,

depending on the output state

The sensor returns to Run mode with the new

seꢃngs.

Present the sensing condiꢀon, then four-pulse the remote line.

TEACH Not Accepted

Power LED Indicator: OFF

Output LED Indicator: Slow ﬂash (1 Hz)

Remote Line

The sensor returns to the wait state, ready for

the sensing condiꢀon.

Dark Set

•

Dark Set sets a threshold approximately 12.5% above the

presented sensing condiꢀon.

Sensor positions

threshold ≈12.5% above

the presented condition

•

Any condiꢀon lighter than the threshold causes the output to

change state.

In Light-Operate mode, the presented condiꢀon is the Output OFF

condiꢀon. In Dark-Operate mode, the presented condiꢀon is the

Output ON condiꢀon. To change the Light-/Dark-Operate seꢃng,

see Sensor Setup on page 3.

Output OFF

Output ON

•

Dark Set is recommended for applicaꢀons where only one

condiꢀon is known, for example a stable dark background with

varying lighter targets, or when maximum excess gain is required.

Single

Presented

Condition

Darkest

(no signal)

Most Light

(saturated

signal)

Figure 6. Dark Set (Light Operate shown)

1. Access the Dark Set mode.

Method

Acꢀon

Result

The sensor waits for the sensing condiꢀon.

Push Buꢂon

Press and hold the push buꢁon 2 to 4 seconds.

Power LED Indicator: OFF

Output LED Indicator: Slow ﬂash (1 Hz)

The iniꢀal output LED indicator condiꢀon is simultaneous with the power LED indicator 3-ﬂash.

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 136564 Rev. E

WORLD-BEAM QS18E Series

Method

Acꢀon

Result

The sensor waits for the sensing condiꢀon.

Remote Line

Single-pulse the remote line.

Power LED Indicator: OFF

Output LED Indicator: Double-ﬂash

2. Set the sensing condiꢀon.

Method

Acꢀon

Result

TEACH Accepted

Present the sensing condiꢀon, then ﬁve-click the push

buꢁon.

Push Buꢂon

Power LED Indicator: Flashes 3 ꢀmes, then

solid green

Output LED Indicator: OFF , then ON or OFF,

depending on the output state

Present the sensing condiꢀon, then ﬁve-pulse the remote line.

The sensor returns to Run mode with the new

seꢃngs.

TEACH Not Accepted

Power LED Indicator: OFF

Output LED Indicator: Slow ﬂash (1 Hz)

Remote Line

The sensor returns to the wait state, ready for

the sensing condiꢀon.

Window Set

•

In Window Set, the single ON condiꢀon window extends

approximately 12.5% above and below the presented condiꢀon

when Light Operate is selected. Output ON and OFF condiꢀons

may be reversed by changing the Light-/Dark-Operate seꢃng (see

Sensor Setup on page 3).

12.5%

Sensor positions

window thresholds

≈12.5% from the

presented condition

•

Lighter or darker condiꢀons outside of the window cause the

output to change state.

Output

Window Set is recommended for applicaꢀons where the target to

be sensed may not always appear in the same place, or when

other unwanted signals may appear.

Output OFF

Darkest

(no signal)

Single

Presented

Condition

Most Light

(saturated

signal)

Figure 7. Window Set (Light Operate shown)

1. Access the Window Set mode.

Method

Acꢀon

Result

The sensor waits for the sensing condiꢀon.

Push Buꢂon

Press and hold the push buꢁon 2 to 4 seconds.

Power LED Indicator: OFF

Output LED Indicator: Slow ﬂash (1 Hz)

The sensor waits for the sensing condiꢀon.

Remote Line

Single-pulse the remote line.

Power LED Indicator: OFF

Output LED Indicator: Double-ﬂash

2. Set the sensing condiꢀon.

Method

Acꢀon

Result

TEACH Accepted

Present the sensing condiꢀon, then double-click the push

buꢁon.

Push Buꢂon

Power LED Indicator: Flashes 3 ꢀmes, then

solid green

Output LED Indicator: OFF , then ON or OFF,

depending on the output state

The sensor returns to Run mode with the new

seꢃngs.

Present the sensing condiꢀon, then double-pulse the

remote line.

TEACH Not Accepted

Remote Line

Power LED Indicator: OFF

Output LED Indicator: Slow ﬂash (1 Hz)

The sensor returns to the wait state, ready for

the sensing condiꢀon.

The iniꢀal output LED indicator condiꢀon is simultaneous with the power LED indicator 3-ﬂash.

P/N 136564 Rev. E

www.bannerengineering.com - Tel: +1-763-544-3164

WORLD-BEAM QS18E Series

Speciꢁcaꢀons

Supply Voltage

Output Protecꢀon Circuitry

10 to 30 V dc (10% maximum ripple) at less than 35 mA, exclusive of load; 10 to 24 V dc

at > 55º C

Protected against false pulse on power-up and conꢀnuous overload or short-circuit of

output

Supply Protecꢀon Circuitry

Output Response

Protected against reverse polarity and transient voltages

Note: Momentary delay on power-up; output does not conduct during this ꢀme

600 µs ON/OFF

Output Conꢁguraꢀon

Repeatability

Current sourcing (PNP) or current sinking (NPN), depending on model; Light- or dark-

operate selectable; Selectable 30 ms output OFF-delay

75 µs

Raꢀng: 100 mA max

Construcꢀon

Oﬀ-state leakage current: less than 50 µA at 30 V dc (see Applicaꢀon Note 1)

ON-state saturaꢀon voltage: less than 1.5 V at 100 mA (1.7V for 30 ꢂ cable models)

ABS housing, PMMA lens

Connecꢀons

PVC-jacketed 4-conductor 2 m (6.5 ꢂ) or 9 m (30 ꢂ) unterminated cable, or 4-pin Euro-

style or 4-pin Pico-style quick-disconnect (QD), either integral or 150 mm (6 in) pigtail,

are available. QD cordsets are ordered separately.

Operaꢀng Condiꢀons

Required Overcurrent Protecꢀon

Temperature: −20 °C to +70 °C (−4 °F to +158 °F)

Relaꢀve Humidity: 95% at +50 °C maximum relaꢀve humidity (non-condensing)

WARNING: Electrical connecꢀons must be made by

qualiﬁed personnel in accordance with local and

naꢀonal electrical codes and regulaꢀons.

Applicaꢀon Notes

If the push buꢁon does not appear to be responsive, perform the push buꢁon enable

procedure

Overcurrent protecꢀon is required to be provided by end product applicaꢀon per the

supplied table.

To maintain backwards compaꢀbility with earlier models, 3 remote line pulses or a push

buꢁon hold followed by 3 push buꢁon clicks will perform a Dark SET.

Overcurrent protecꢀon may be provided with external fusing or via Current Limiꢀng,

Class 2 Power Supply.

Cerꢀꢁcaꢀons

Supply wiring leads < 24 AWG shall not be spliced.

For addiꢀonal product support, go to www.bannerengineering.com.

Supply Wiring (AWG)

Required Overcurrent Protecꢀon (Amps)

5.0

3.0

2.0

1.0

0.8

0.5

Dimensions

Model Suffix E, EV, R, FF

Model Suffix EB, RB

Model Suffix DB, W

Model Suffix FP

31.0 mm

(1.22")

27.5 mm

(1.09")

21.1 mm

(0.82")

21.1 mm

(0.82")

15.0 mm

(0.59")

17.1 mm

Yellow

LED

Green

LED

17.1 mm

(0.67")

15.0 mm

(0.59")

3.0 mm

(0.12")

3.0 mm

(0.12")

7.5 mm

(0.30")

3.0 mm

(0.12")

13.4 mm

(0.53")

24.1 mm

(0.95")

35.0 mm

(1.38")

5.2 mm

(0.21")

7.6 mm

(0.30")

Ø3.3 mm (0.13")

Max. torque 0.9 Nm (8 lbf. in)

_{QS18...FP Fiber Installation}A

Model Suffix F

Model Suffix CV15, CV45, D, DL, LV, LP

31.0 mm^†

36.9 mm

(1.45")

A.Slide the fiber clip to open.

Single-turn

(1.22")

Sensitivity

B.Insert fiber ends into each port,

as far as they will go.

C.Slide the fiber clip closed,

locking fibers into position.

3.0 mm

17.1 mm

(0.67")

19.8 mm

(0.78")

Adjustment

(0.12")

*Model Suffix Q

(e.g. QS186EQ)

*Model Suffix Q5

(e.g. QS186EQ5)

*Model Suffix Q7

(e.g. QS186EQ7)

*Model Suffix Q8

(e.g. QS186EQ8)

M18x1 Thread

Max. torque 2.3 Nm (20 lbf. in)

Slot for

Fiber Clip

^†CV Models:

33.2 mm (1.31")

M18 x 1 Jam Nut

41.5 mm

(1.63")

49 mm

(1.93")

M3 Hardware Packet Contents:

2 – M3 x 0.5 x 20 mm SS screw

2 – M3 x 0.5 SS hex nut

24.2 mm(0.95")

Packing List

Sensor

M18 x 1 jam nut

M3 hardware packet

Installation sheet P/N 63687

150 mm (6")

Euro-style

Pigtail

2 – M3 SS washer

8.0 mm(0.32")

Integral

4-pin

Pico-Style QD

Integral

4-pin

Euro-Style QD

150 mm (6")

Pico-style

Pigtail

All measurements are listed in millimeters [inches], unless noted otherwise.

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 136564 Rev. E

WORLD-BEAM QS18E Series

Performance Curves

Performance using Dark Set, performed in no-light condiꢀon.

Polarized Retroreꢄecꢀve

Excess Gain

Beam Paꢂern

Diﬀuse (Based on use of 90% reꢄectance white test card.)

Excess Gain

Beam Paꢂern

Excess Gain

Beam Paꢂern

Convergent

Excess Gain

Beam Paꢂern

Excess Gain

Beam Paꢂern

Fiber Opꢀc - Plasꢀc

Excess Gain

Beam Paꢂern

Excess Gain

Beam Paꢂern

P/N 136564 Rev. E

www.bannerengineering.com - Tel: +1-763-544-3164

WORLD-BEAM QS18E Series

Accessories

4-Pin Snap-on M8/Pico-Style Cordsets

Model

Length

Style

Dimensions

Pinout (Female)

32 Typ.

PKG4-2

2 m (6.56 ꢂ)

Straight

ø 9.0

29 Typ.

1 = Brown

2 = White

3 = Blue

PKW4Z-2

2 m (6.56 ꢂ)

Right-Angle

15 Typ.

4 = Black

ø 10.9

4-Pin Threaded M12/Euro-Style Cordsets

Model

Length

Style

Dimensions

Pinout (Female)

MQDC-406

MQDC-415

MQDC-430

1.83 m (6 ꢂ)

4.57 m (15 ꢂ)

9.14 m (30 ꢂ)

44 Typ.

Straight

M12 x 1

ø 14.5

MQDC-450

15.2 m (50 ꢂ)

MQDC-406RA

MQDC-415RA

MQDC-430RA

1.83 m (6 ꢂ)

4.57 m (15 ꢂ)

9.14 m (30 ꢂ)

32 Typ.

[1.26"]

1 = Brown

2 = White

3 = Blue

30 Typ.

[1.18"]

Right-Angle

4 = Black

MQDC-450RA

15.2 m (50 ꢂ)

M12 x 1

ø 14.5 [0.57"]

SMB312S

SMBQS18DIN

•

Right-angle bracket

assembly for mounꢀng on

35 mm DIN rail

•

Stainless steel 2-axis, side-

mount bracket

•

300 series stainless steel

and glass ﬁlled nylon; zinc-

plated screws

A = 4.3 × 7.5, B = diam. 3, C = 3 × 15.3

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 136564 Rev. E

WORLD-BEAM QS18E Series

SMBQS18Y

SMB18A

3.4 mm

[0.13"]

•

Die-cast bracket for 18 mm

15.5 mm

[0.61"]

•

Right-angle mounꢀng

bracket with a curved slot

for versaꢀle orientaꢀon

holes

4.5 mm

[0.18"]

7.8 mm

[0.31"]

Includes metal hex nut and

lock washer

Allows ± 8° for cabled

sensors

•

12-ga. stainless steel

2x R24.1 mm

[0.95"]

24.1 mm

[0.94"]

18 mm sensor mounꢀng

38.0 mm

[1.50"]

hole

•

Clearance for M4 (#8)

hardware

Hole size: A = ø 15.3

12.0 mm

[0.47"]

25.4 mm

[1"]

Hole center spacing: A to B = 24.2

Hole size: A = ø 4.6, B = 17.0 × 4.6, C = ø 18.5

16.4 mm

[0.65"]

9.8 mm

[0.38"]

19.5 mm

[0.77"]

14.5 mm

[0.57"]

SMB4050YL

SMB3018SC

•

Heavy-duty die-cast bracket

•

18 mm swivel side or barrel-

for industrial protecꢀon

mount bracket

Replaceable window for use

with some sensor models

M18 verꢀcal mounꢀng

opꢀon

Nut and lock washer

included

Black reinforced

thermoplasꢀc polyester

Stainless steel swivel locking

hardware included

A = ø 15.3

Hole center spacing: A = 50.8

Hole size: A = ø 7.0, B = ø 18.0

Addiꢀonal available brackets: SMB46A, SMB18SF, SMBQS18RA, SMB18FA, SMBQS18A

For a list of reﬂectors or ﬁber opꢀc assemblies, refer to the Accessories secꢀon of your current Banner Sensors catalog or visit

www.bannerengineering.com for complete informaꢀon.

Banner Engineering Corp. Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any

product of its manufacture which, at the ꢀme it is returned to the factory, is found to have been defecꢀve during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the

improper applicaꢀon or installaꢀon of the Banner product.

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.

This Warranty is exclusive and limited to repair or, at the discreꢀon of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR

ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO

USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligaꢀons or liabiliꢀes relaꢀng to any product previously manufactured by Banner

Engineering Corp. Any misuse, abuse, or improper applicaꢀon or installaꢀon of this product or use of the product for personal protecꢀon applicaꢀons when the product is idenꢀﬁed as not intended for such purposes

will void the product warranty. Any modiﬁcaꢀons to this product without prior express approval by Banner Engineering Corp will void the product warranꢀes. All speciﬁcaꢀons published in this document are subject

to change; Banner reserves the right to modify product speciﬁcaꢀons or update documentaꢀon at any ꢀme. Speciﬁcaꢀons and product informaꢀon in English supersede that which is provided in any other language.

For the most recent version of any documentaꢀon, refer to: www.bannerengineering.com.

QS18E [BANNER]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E