SMA30PELC [BANNER]
SM30 Series 30 mm Barrel Sensors;型号: | SMA30PELC |
厂家: | Banner Engineering |
描述: | SM30 Series 30 mm Barrel Sensors |
文件: | 总5页 (文件大小:350K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SM30 Series 30 mm Barrel Sensors
Datasheet
Opposed-Mode Infrared Photoelectric Sensors for Especially Demanding Applicaꢀons
•
•
•
Stainless steel or plasꢀc barrel models
Very high excess gain; 150 m (500 ꢁ) sensing range; 880 nm Infrared LED
Posiꢀve sealing eliminates even capillary leakage; lens is quad-ring sealed; exceeds NEMA
6P (IP67) raꢀngs – ideal for equipment wash-down environments
®
•
•
EZ-BEAM technology provides reliable sensing without the need for adjustment
Modulaꢀon frequency “A” is standard; frequencies “B” and “C” also available for
prevenꢀng crosstalk in mulꢀple-sensor applicaꢀons (emiꢂer and opposed receiver
frequencies must match)
•
•
AC- and DC-operated receiver models available; emiꢂers feature Universal voltage
Range for all models: 150 m (500 ꢁ)
WARNING: Not To Be Used for Personnel Protecꢀon
Never use this device as a sensing device for personnel protecꢀon. Doing so could lead to serious injury or death.
This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety
applicaꢀons. A sensor failure or malfuncꢀon can cause either an energized or de-energized sensor output
condiꢀon.
Models
1
2
Modulaꢀon Frequency
Housing
Cable
Power Supply
Output Type
A
B
C
Emiꢁer Models
SMA30PEL
SMA30PELB
SMA30PELC
2 m (6.5 ꢁ) 2-wire Cable
Plasꢀc
3
SMA30PELQD
SMA30SEL
SMA30PELQDB
SMA30SELB
SMA30PELQDC
SMA30SELC
3-pin Mini-style QD
Universal: 12 to 240
V ac, 10 to 30 V dc
–
2 m (6.5 ꢁ) 3-wire Cable
Stainless Steel
3
SMA30SELQD
DC Receivers
SM30PRL
SMA30SELQDB
SMA30SELQDC
3-pin Mini-style QD
SM30PRLB
SM30PRLC
2 m (6.5 ꢁ) 4-wire Cable
4-pin Mini-style QD
Plasꢀc
SM30PRLQD
SM30SRL
SM30PRLQDB
SM30SRLB
SM30PRLQDC
SM30SRLC
™
Bi-Modal NPN or
PNP
10 to 30 V dc
2 m (6.5 ꢁ) 4-wire Cable
4-pin Mini-style QD
Stainless Steel
SM30SRLQD
AC Receivers
SM2A30PRL
SM2A30PRLQD
SM2A30SRL
SM2A30SRLQD
SM2A30PRLNC
SM2A30PRLNCQD
SM2A30SRLNC
SM2A30SRLNCQD
SM30SRLQDB
SM30SRLQDC
SM2A30PRLB
SM2A30PRLC
2 m (6.5 ꢁ) 2-wire Cable
Plasꢀc
Stainless Steel
Plasꢀc
3
SM2A30PRLQDB
SM2A30SRLB
SM2A30PRLQDC
SM2A30SRLC
3-pin Mini-style QD
SPST Solid-state,
L.O.
2 m (6.5 ꢁ) 3-wire Cable
3
SM2A30SRLQDB
SM2A30PRLNCB
SM2A30PRLNCQDB
SM2A30SRLNCB
SM2A30SRLNCQDB
SM2A30SRLQDC
SM2A30PRLNCC
SM2A30PRLNCQDC
SM2A30SRLNCC
SM2A30SRLNCQDC
3-pin Mini-style QD
24 to 240 V ac
2 m (6.5 ꢁ) 2-wire Cable
3
3-pin Mini-style QD
SPST Solid-state,
D.O.
2 m (6.5 ꢁ) 3-wire Cable
Stainless Steel
3
3-pin Mini-style QD
1
2
Any emiꢂer and receiver shown here can be used together, if they have the same modulaꢀon frequency.
Standard 2 m (6.5 ꢁ) cable and integral QD models are listed. Models with a quick disconnect require a maꢀng cordset. To order the 9 m (30 ꢁ) PVC cable model,
add the suffix "W/30" to the cabled model number. For example, SM30PRLBW/30.
3
AC models with QD require SM30CC model cables.
Original Document
03541 Rev. G
25 May 2017
03541
SM30 Series 30 mm Barrel Sensors
Wiring Diagrams
Key
1 = Brown (red/black for QD emiꢂers/receivers)
3 = Blue (red/white for QD emiꢂers/receivers)
4 = Green (green for QD emiꢂers/receivers)
Emiꢁers—Cabled
Emiꢁers—QD
AC Receivers—Cabled
AC Receivers—QD
1
3
4
1
10-30V dc or
12-240V ac
1
1
24-240V ac
3
10-30V dc or
12-240V ac
Load
24-240V ac
3
3
4
Load
4*
4*
Note: AC emiꢂers are not polarity-sensiꢀve
when powered by dc voltage. For QD
emiꢂers, use a SM30CC model cordset to
match cable colors.
*Connect the green wire to earth ground whenever a stainless steel model is powered by ac voltage. (Cabled plasꢀc models have no
green wire.)
Key
1 = Brown
2 = White
3 = Blue
4 = Black
DC Receivers—NPN
DC Receivers—PNP
3
1
4
2
3
1
4
2
3
1
4
3
1
4
2
–
10-30V dc
+
–
+
10-30V dc
–
+
10-30V dc
–
10-30V dc
+
Load
Load
Load
Load
2
Light Operate
Dark Operate
Light Operate
Dark Operate
Cabled wiring diagrams are funcꢀonally idenꢀcal.
2
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 03541 Rev. G
SM30 Series 30 mm Barrel Sensors
Speciꢂcaꢀons
Supply Voltage and Current
Environmental Raꢀng
Emiꢂers: 12 to 240V ac (50/60 Hz) or 10-30V dc at 20 mA, 10% maximum
Exceeds NEMA 6P and IEC IP67
ripple
Connecꢀons
DC Receivers: 10 to 30V dc at 10 mA maximum (exclusive of load); 10%
maximum ripple
AC Receivers: 24 to 240V ac (50/60 Hz)
PVC-jacketed 2 m or 9 m cables or Mini-style quick-disconnect (QD) ꢃꢄng are
available. QD cables are ordered separately.
Operaꢀng Condiꢀons
Supply Protecꢀon Circuitry
Temperature: −40 °C to +70 °C (−40 °F to +158 °F)
90% at +50 °C maximum relaꢀve humidity (non-condensing)
Protected against reverse polarity and transient voltages
Output Conꢂguraꢀon
Required Overcurrent Protecꢀon
™
DC Receivers: Bi-Modal output (PNP sourcing or NPN sinking). Selecꢀon of
light/dark operate and sourcing or sinking conꢃguraꢀon dependent on hookup.
AC Receivers: SPST solid-state switch; light operate (LO) or dark operate (DO)
dependent on model.
WARNING: Electrical connecꢀons must be made
by qualiꢃed personnel in accordance with local
and naꢀonal electrical codes and regulaꢀons.
Output Raꢀng
Overcurrent protecꢀon is required to be provided by end product applicaꢀon
per the supplied table.
DC Receivers: 250 mA conꢀnuous
Output saturaꢀon voltage (PNP & NPN conꢃguraꢀon) < 1 volt at 10 mA and < 2
volts at 250 mA
Overcurrent protecꢀon may be provided with external fusing or via Current
Limiꢀng, Class 2 Power Supply.
Off-state leakage current < 10 microamps
AC Receivers: Maximum steady-state load capability is 500 mA
Supply wiring leads < 24 AWG shall not be spliced.
For addiꢀonal product support, go to www.bannerengineering.com.
Inrush capability: 10 amps for 1 second (non-repeaꢀng)
Off-state leakage: current < 1.7 mA rms
On-state voltage drop: < 3.5 volts rms across a 500 mA load; < 5 volts rms
across a 15 mA load
Supply Wiring (AWG)
Required Overcurrent Protecꢀon (Amps)
20
22
24
26
28
30
5.0
3.0
2.0
1.0
0.8
0.5
Output Protecꢀon Circuitry
Outputs of dc receivers are short circuit protected
Output Response Time
10 milliseconds on/off
Repeatability
“A” frequency models: 1 ms
“B” frequency models: 1.5 ms
“C” frequency models: 2.3 ms
Indicators
Internal red LED, visible through the lens or from side of the sensor.
Cerꢀꢂcaꢀons
Emiꢂers: Red “Power ON” indicator LED
DC Receivers: Lights whenever receiver sees its modulated light source
AC Receivers: Lights whenever receiver’s output is conducꢀng
Construcꢀon
Fully epoxy-encapsulated tubular threaded housing, posiꢀve sealed at both
ends, quad-ring sealed acrylic lens.
Plasꢀc models: 30 mm diameter thermoplasꢀc polyester housing and jam nuts.
Stainless Steel models: 30 mm diameter 303 stainless steel housing and jam
nuts.
Dimensions
All measurements are listed in millimeters [inches], unless noted otherwise.
Cabled Models
QD Models
Jam Nuts
(2 Provided)
Jam Nuts
(2 Provided)
Alignment
Indicator (Receivers)
Alignment
Indicator (Receivers)
M30 x 1.5
Thread
M30 x 1.5
Thread
102 mm
(4.0")
114 mm
(4.5")
P/N 03541 Rev. G
www.bannerengineering.com - Tel: +1-763-544-3164
3
SM30 Series 30 mm Barrel Sensors
Performance Curves
Excess Gain Curve
Beam Paꢂern
100000
10000
1000
1500 mm
60 in
SM30 Series
Opposed Mode
SM30 Series
Opposed Mode
1000 mm
500 mm
0
40 in
20 in
0
E
X
C
E
S
S
500 mm
1000 mm
1500 mm
20 in
40 in
60 in
100
10
G
A
I
N
0
45 m
150 ft
90 m
300 ft
135 m
450 ft
180 m
600 ft
225 m
750 ft
DISTANCE
1
1 m
3.3 ft
10 m
33 ft
100 m
330 ft
1000 m
3300 ft
DISTANCE
Accessories
Cordsets
3-Pin Mini-Style Cordsets
Model
Length
Style
Dimensions
Pinout (Female)
SM30CC-306
1.83 m (6 ꢁ)
4
52 Typ.
7/8-16UN-2B
ø 25.5
1
3
Straight
SM30CC-312
3.66 m (12 ꢁ)
1 = Red/Black
3 = Red/White
4 = Green
4-Pin Mini-Style Cordsets
Model
Length
Style
Dimensions
Pinout (Female)
MBCC-406
1.83 m (6 ꢁ)
3.66 m (12 ꢁ)
4
3
2
1
MBCC-412
52 Typ.
7/8-16UN-2B
ø 25.5
Straight
1 = Brown
2 = White
3 = Blue
MBCC-430
9.14 m (30 ꢁ)
4 = Black
Apertures
APG30S
Kit includes round apertures of 0.05 in, 0.12 in, and 0.70 in diameter; sloꢂed widths of 1 mm (0.04 in), 0.10 in and
0.20 in.
Used with SM30 and SMI30 models.
4
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 03541 Rev. G
SM30 Series 30 mm Barrel Sensors
Brackets
SMB30C
56
SMB30A
45
•
Right-angle bracket with curved
•
30 mm split clamp, black PBT
bracket
Stainless steel mounꢀng
hardware included
Mounꢀng hole for 30 mm
slot for versaꢀle orientaꢀon
C
A
•
•
•
Clearance for M6 (¼ in)
hardware
Mounꢀng hole for 30 mm
sensor
61
66
•
•
B
B
A
12-ga. stainless steel
sensor
69
13
Hole center spacing: A to B=40
Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5
Hole center spacing: A=ø 45
Hole size: B=ø 27.2
SMB30MM
SMB30SC
67
•
12-ga. stainless steel bracket
with curved mounꢀng slots for
versaꢀle orientaꢀon
•
•
•
Swivel bracket with 30 mm
57
70
B
mounꢀng hole for sensor
Black reinforced thermoplasꢀc
polyester
Stainless steel mounꢀng and
swivel locking hardware
included
58
C
•
•
Clearance for M6 (¼ in)
57
hardware
B
Mounꢀng hole for 30 mm
sensor
A
29
A
Hole center spacing: A = 51, A to B = 25.4
Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1
Hole center spacing: A=ø 50.8
Hole size: A=ø 7.0, B=ø 30.0
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or
replace, free of charge, any product of its manufacture which, at the ꢀme it is returned to the factory, is found to have been defecꢀve during the warranty period. This warranty does not cover
damage or liability for misuse, abuse, or the improper applicaꢀon or installaꢀon of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discreꢀon of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY
OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT
DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligaꢀons or liabiliꢀes relaꢀng to any product previously
manufactured by Banner Engineering Corp. Any misuse, abuse, or improper applicaꢀon or installaꢀon of this product or use of the product for personal protecꢀon applicaꢀons when the
product is idenꢀꢃed as not intended for such purposes will void the product warranty. Any modiꢃcaꢀons to this product without prior express approval by Banner Engineering Corp will void the
product warranꢀes. All speciꢃcaꢀons published in this document are subject to change; Banner reserves the right to modify product speciꢃcaꢀons or update documentaꢀon at any ꢀme.
Speciꢃcaꢀons and product informaꢀon in English supersede that which is provided in any other language. For the most recent version of any documentaꢀon, refer to:
www.bannerengineering.com.
©
Banner Engineering Corp. All rights reserved
相关型号:
©2020 ICPDF网 联系我们和版权申明