WL50SGL20Q [BANNER]
WL50S High-Intensity Work Spot Light;
| 型号： | WL50SGL20Q |
| 厂家： | 
Banner Engineering |
| 描述： | WL50S High-Intensity Work Spot Light |
| 文件： | 总5页 (文件大小：287K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
WL50S High-Intensity Work Spot Light
Datasheet
General-purpose LED work lighting
To view or download the latest technical information about this product, including specifications, dimensions, accessories,
and wiring, see http://www.bannerengineering.com.
•
•
•
•
•
•
Three lens options, depending on model, to vary spot size
Illuminates a large area with an even pattern of light and no shadows
12 to 30 V dc operation
Cabled and quick-disconnect models available
50 mm diameter with flat profile and 30 mm mounting base
Rugged sealed housing rated to IP69K
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to
serious injury or death. This device does not include the self-checking redundant circuitry necessary
to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an
energized or de-energized sensor output condition.
Models
Model1
LED Color
Lumens
Lux
Lens Angle
Connection
0.5 m
13780
8000
13000
5460
2500
3900
2000
1040
1700
1 m
3445
2000
3250
1365
625
WL50SWL5Q
WL50SRL5Q
WL50SGL5Q
WL50SWL11Q
WL50SRL11Q
WL50SGL11Q
WL50SWL20Q
WL50SRL20Q
WL50SGL20Q
White, 5000-8300 K
Red, 620-630 nm
Green, 520-535 nm
White, 5000-8300 K
Red, 620-630 nm
Green, 520-535 nm
White, 5000-8300 K
Red, 620-630 nm
Green, 520-535 nm
295
110
210
285
105
200
270
100
190
±5° (smaller,
more focused
spot; see graph)
5 pin Euro integral
QD connector (use
with a 4-wire
mating cordset;
only 2 wires used
for connection)
±11° (larger
spot; see graph)
975
500
±20° (largest
spot; see graph)
260
425
1
Integral QD models only are listed. For integral 2 m (6.5') PVC cable, omit suffix Q from model number (example, WL50SWL5). A model with a QD
requires a mating cordset (see 4-Pin Euro-Style Cordsets on page 3).
Original Document
158250 Rev. E
21 April 2016
158250
WL50S High-Intensity Work Spot Light
Specifications
Supply Voltage and Current
Environmental Rating
Operating voltage: 12 V to 30 V dc
Current draw: 400 mA maximum
IEC IP67, IP69K per DIN 40050-9
NOTE: Do not spray the cable with a
Supply Protection Circuitry
high-pressure sprayer or cable damage
will result.
Protected against reverse polarity and transient voltages
Light Source
Three high-intensity LEDs; see models table for color temperature or
wavelengths
Operating Conditions
−20 °C to +50 °C (−4 °F to +122 °F)
95% maximum relative humidity (non-condensing)
Useful Life
When operating within specifications, output will decrease less than
30% after 50,000 hours.
Vibration and Mechanical Shock
All models meet Mil. Std. 202F requirements method 201A (vibration:
10 to 60 Hz max., double amplitude 0.06", maximum acceleration
10G). Also meets IEC 947-5-2; 30G 11 ms duration, half sine wave.
Construction
Black anodized aluminum housing; polycarbonate window; nickel-
plated QD connector or PVC-jacketed cable; black zinc-plated steel
mounting nut
Storage Temperature
−40 °C to +70 °C (−40 °F to +158 °F)
Mounting:
Certifications
30 × 1.5 mm thread base mount
Connections
Integral 5-pin M12 quick disconnect fitting or 2 m (6.5 ft) integral
cable, depending on model; 4-pin connecting cordset required for quick
disconnect fitting models; only 2 wires used
UL Recognized for
easy installation in
control cabinets
Beam Patterns
Percentage of Maximum Light Intensity Per
Lens Type at 0.5 Meter (Typical)
Percentage of Maximum Light Intensity Per Lens Type at 1
Meter (Typical)
100%
75%
50%
100%
75%
50%
25%
25%
±5º
±14˚
±20º
±11º ±14º
±5˚
±20˚
±11˚
0%
–30
0%
−60
–20
–10
0
10
20
30
−50
−40
−30
−20
−10
0
10
20
30
40
50
60
Light Pattern From Center (cm)
Light Pattern From Center (cm)
2
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 158250 Rev. E
WL50S High-Intensity Work Spot Light
Dimensions
Wiring
Wiring Key:
1 = Brown
3 = Blue
Female
Male
1
1
1
3
+
3
3
12–30 V dc
−
4-Pin Euro-Style Cordsets
4-Pin Threaded M12/Euro-Style Cordsets
Model
Length
Style
Dimensions
Pinout (Female)
MQDC-406
MQDC-415
MQDC-430
1.83 m (6 ft)
4.57 m (15 ft)
9.14 m (30 ft)
2
3
44 Typ.
1
4
Straight
M12 x 1
ø 14.5
1 = Brown
2 = White
3 = Blue
MQDC-450
15.2 m (50 ft)
4 = Black
P/N 158250 Rev. E
www.bannerengineering.com - Tel: +1-763-544-3164
3
WL50S High-Intensity Work Spot Light
4-Pin Threaded M12/Euro-Style Cordsets
Model
Length
Style
Dimensions
Pinout (Female)
MQDC-406RA
MQDC-415RA
MQDC-430RA
1.83 m (6 ft)
4.57 m (15 ft)
9.14 m (30 ft)
32 Typ.
[1.26"]
30 Typ.
[1.18"]
Right-Angle
MQDC-450RA
15.2 m (50 ft)
M12 x 1
ø 14.5 [0.57"]
Mounting Brackets
All measurements are in mm
67
45
SMB30A
SMB30SC
•
Right-angle bracket with
curved slot for versatile
orientation
Clearance for M6 (¼ in)
hardware
Mounting hole for 30 mm
sensor
12-ga. stainless steel
•
•
•
Swivel bracket with 30 mm
mounting hole for sensor
Black reinforced
B
C
61
58
•
•
•
thermoplastic polyester
B
Stainless steel mounting and
swivel locking hardware
included
A
29
69
A
Hole center spacing: A=ø 50.8
Hole size: A=ø 7.0, B=ø 30.0
Hole center spacing: A to B=40
Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5
SMB30FA
SMBAMS30RA
45
83.2
•
Swivel bracket with tilt and
pan movement for precise
adjustment
•
•
•
•
Right-angle SMBAMS series
bracket
30 mm hole for mounting
sensors
Articulation slots for 90°+
rotation
12-ga. (2.6 mm) cold-rolled
steel
C
53
A
•
Mounting hole for 30 mm
sensor
B
68.9
36.3
B
•
•
12-ga. 304 stainless steel
Easy sensor mounting to
extrude rail T-slot
48
A
•
Metric and inch size bolt
available
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
Bolt thread: SMB30FA, A= 3/8 - 16 x 2 in; SMB30FAM10, A= M10 -
1.5 x 50
Hole size: B= ø 30.1
45
SMB30MM
SMBAMS30P
57
70
•
12-ga. stainless steel bracket
with curved mounting slots
for versatile orientation
•
•
Flat SMBAMS series bracket
30 mm hole for mounting
sensors
C
C
A
93
57
•
•
Clearance for M6 (¼ in)
hardware
Mounting hole for 30 mm
sensor
•
•
Articulation slots for 90°+
rotation
12-ga. 300 series stainless
steel
B
B
A
Hole center spacing: A = 51, A to B = 25.4
Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
4
www.bannerengineering.com - Tel: +1-763-544-3164
P/N 158250 Rev. E
WL50S High-Intensity Work Spot Light
Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following
the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture
which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty
does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR
IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR
TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO
EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR
ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR
SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE
PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY,
NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any
obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp.
Copyright Notice
Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not
intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product
warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any
©
time. For the most recent version of any documentation, refer to: www.bannerengineering.com.
Banner Engineering Corp. All rights reserved.
www.bannerengineering.com - Tel: +1-763-544-3164
相关型号：
WL50SGL5Q
WL50S High-Intensity Work Spot LightWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BANNER
WL50SRL11Q
WL50S High-Intensity Work Spot LightWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BANNER
WL50SRL20Q
WL50S High-Intensity Work Spot LightWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BANNER
WL50SRL5Q
WL50S High-Intensity Work Spot LightWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BANNER
WL50SWL11PWMQ
WL50S High-Intensity Spot Light - PWM DimmableWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BANNER
WL50SWL11Q
WL50S High-Intensity Work Spot LightWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BANNER
WL50SWL20PWMQ
WL50S High-Intensity Spot Light - PWM DimmableWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BANNER
WL50SWL20Q
WL50S High-Intensity Work Spot LightWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BANNER
WL50SWL5PWMQ
WL50S High-Intensity Spot Light - PWM DimmableWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BANNER
WL50SWL5Q
WL50S High-Intensity Work Spot LightWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BANNER
WL50SWSSGL11PWMQ
WL50S Stainless Steel High-Intensity Spot Light - PWM DimmableWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BANNER
WL50SWSSGL11Q
WL50S Stainless Steel High-Intensity Work Spot LightWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
BANNER
©2020 ICPDF网 联系我们和版权申明