WL50SWSSGL11PWMQ [BANNER]
WL50S Stainless Steel High-Intensity Spot Light - PWM Dimmable;
| 型号： | WL50SWSSGL11PWMQ |
| 厂家： | 
Banner Engineering |
| 描述： | WL50S Stainless Steel High-Intensity Spot Light - PWM Dimmable |
| 文件： | 总5页 (文件大小：445K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
WL50S Stainless Steel High-Intensity Spot
Light - PWM Dimmable
Datasheet
Chemically Resistant LED work lighting
•
Intensity can be controlled from 0 to 100% using Pulse Width Modulation (PWM) on
an input control wire
•
•
•
•
•
•
•
Three lens options, depending on model, to vary spot size
Illuminates a large area with an even pattern of light and no shadows
12 to 30 V dc operation
56 mm (2.2 in) diameter with flat profile and 30 mm (1.2 in) mounting base
®
Rugged, Viton o-ring sealed housing rated to IP69K
Chemically resistant 316 stainless steel housing for use in harsh environments
FDA grade silicone gasket
Use with the LC65 Dimmer Module. For more information, refer to the LC65 LED
Dimmer Module datasheet, p/n 177086.
Lux
Lens Angle
Model
LED Color
Window Material
Lumens
Connection
(see Beam
Patterns on
page 2)
0.5 m
1 m
WL50SWSSL5PWMQ
WL50SWSSGL5PWMQ
Polycarbonate
Glass
±5°
295
13780
3445
small, more
focused spot
5-pin Euro-style integral QD
connector (use with a 4-
wire or 5-wire mating
cordset, only 3 wires used
for connection)
White,
WL50SWSSL11PWMQ
WL50SWSSGL11PWMQ
Polycarbonate
Glass
±11°
285
270
5460
2000
1365
500
5000–8300 K
larger spot
±20°
WL50SWSSL20PWMQ
WL50SWSSGL20PWMQ
Polycarbonate
Glass
largest spot
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to
serious injury or death. This device does not include the self-checking redundant circuitry necessary
to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an
energized or de-energized sensor output condition.
Original Document
179497 Rev. A
8 April 2014
179497
WL50S Stainless Steel High-Intensity Spot Light - PWM Dimmable
Specifications
Supply Voltage and Current
Operating Voltage: 12 to 30V dc
Current Draw: 400 mA max.
Mounting
30x1.5 mm thread base mount
Connections
Pulse Width Modulation (PWM)
Frequency: Up to 40 kHz
Voltage: 5 to 30 V dc
Integral 5-pin M12/Euro style QD; 4-pin connecting cordset required
for QD models; only 2 wires used
Environmental Rating
Current: 15 mA max.
IEC IP67, IP69K per DIN 40050-9
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
NOTE: Do not spray the cable with a
high-pressure sprayer or cable damage
will result.
Light Source
Three high-intensity LEDs; see models table for color temperature
Useful Life
Operating Conditions
When operating within specifications, output will decrease less than
30% after 50,000 hours.
-20° to +50°C (-4° to +122°F)
95% max. relative humidity (non-condensing)
Construction
Vibration and Mechanical Shock
316 stainless steel housing, polycarbonate or glass window with Viton
seal, 316 stainless steel M30 mounting nut, FDA grade silicon base
gasket
All models meet Mil. Std. 202F requirements method 201A (vibration:
10 to 60 Hz max., double amplitude 0.06", maximum acceleration
10G). Also meets IEC 947-5-2; 30G 11 ms duration, half sine wave.
Storage Temperature
−40 °C to +70 °C (−40 °F to +158 °F)
95% maximum relative humidity (non-condensing)
Certifications
Approvals are pending
Beam Patterns
Percentage of Maximum Light Intensity
Per Lens Type at 0.5 Meter (Typical)
Percentage of Maximum Light Intensity Per Lens Type at 1 Meter
(Typical)
100%
75%
50%
25%
100%
75%
50%
25%
±5º
±20º
±5º
±20º
±11º
±11º
0%
0%
-30
-20
-10
0
10
20
30
-60
-50
-40
-30
-20
-10
0
10
20
30
40
50
60
Light Pattern From Center (cm)
Light Pattern From Center (cm)
2
www.bannerengineering.com - tel: 763-544-3164
P/N 179497 Rev. A
WL50S Stainless Steel High-Intensity Spot Light - PWM Dimmable
Dimensions
Wiring
Pins
Color
Color/Connection
12 to 30 V dc
1
3
4
2
brown
blue
2
3
1
4
dc common
black
white
Not used
Pulse Width Modulation (PWM) input
For maximum intensity, leave the white and black wires floating or connected to common.
Accessories
Cordsets
Standard Cordsets
4-Pin Threaded M12/Euro-Style Cordsets
Model
MQDC-406
Length
Style
Dimensions
Pinout
1.83 m (6 ft)
4.57 m (15 ft)
9.14 m (30 ft)
15.2 m (50 ft)
44 Typ.
MQDC-415
MQDC-430
MQDC-450
2
3
1
4
M12 x 1
ø 14.5
Straight
1 = Brown
2 = White
3 = Blue
4 = Black
P/N 179497 Rev. A
www.bannerengineering.com - tel: 763-544-3164
3
WL50S Stainless Steel High-Intensity Spot Light - PWM Dimmable
4-Pin Threaded M12/Euro-Style Cordsets
Model
MQDC-406RA
Length
Style
Dimensions
Pinout
1.83 m (6 ft)
4.57 m (15 ft)
9.14 m (30 ft)
15.2 m (50 ft)
32 Typ.
[1.26"]
MQDC-415RA
MQDC-430RA
MQDC-450RA
30 Typ.
[1.18"]
Right-Angle
M12 x 1
ø 14.5 [0.57"]
Washdown Rated Cordsets
Polypropylene jacket and connector body, stainless steel coupling nut
5-Pin Threaded M12/Euro-Style Cordsets―Washdown
Model
Length
Style
Dimensions
Pinout
MQDCWD-506
1.83 m (6 ft)
2
1
4
42 Typ.
[1.65"]
3
5
ø 15.0
[0.57"]
Straight
1 = Brown
MQDCWD-530
9.14 m (30 ft)
2 = White
3 = Blue
4 = Black
5 = Gray
M12 x 1
Mounting Brackets
All measurements are in mm
67
45
SMB30A
SMB30SC
•
Right-angle bracket with
curved slot for versatile
orientation
Clearance for M6 (¼ in)
hardware
Mounting hole for 30 mm
sensor
12-ga. stainless steel
•
•
•
Swivel bracket with 30 mm
mounting hole for sensor
Black reinforced
B
C
61
58
•
•
•
thermoplastic polyester
B
Stainless steel mounting and
swivel locking hardware
included
A
29
69
A
Hole center spacing: A=ø 50.8
Hole size: A=ø 7.0, B=ø 30.0
Hole center spacing: A to B=40
Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5
4
www.bannerengineering.com - tel: 763-544-3164
P/N 179497 Rev. A
WL50S Stainless Steel High-Intensity Spot Light - PWM Dimmable
SMB30FA
SMBAMS30RA
45
83.2
•
Swivel bracket with tilt and
pan movement for precise
adjustment
•
•
•
•
Right-angle SMBAMS series
bracket
30 mm hole for mounting
sensors
Articulation slots for 90°+
rotation
12-ga. (2.6 mm) cold-rolled
steel
C
53
A
•
Mounting hole for 30 mm
sensor
B
68.9
36.3
B
•
•
12-ga. 304 stainless steel
Easy sensor mounting to
extrude rail T-slot
48
A
•
Metric and inch size bolt
available
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
Bolt thread: SMB30FA, A= 3/8 - 16 x 2 in; SMB30FAM10, A= M10 -
1.5 x 50
Hole size: B= ø 30.1
45
SMB30MM
SMBAMS30P
57
70
•
12-ga. stainless steel bracket
with curved mounting slots
for versatile orientation
•
•
Flat SMBAMS series bracket
30 mm hole for mounting
sensors
C
C
A
93
57
•
•
Clearance for M6 (¼ in)
hardware
Mounting hole for 30 mm
sensor
•
•
Articulation slots for 90°+
rotation
12-ga. 300 series stainless
steel
B
B
A
Hole center spacing: A = 51, A to B = 25.4
Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following
the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture
which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty
does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR
IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR
TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO
EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR
ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR
SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE
PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY,
NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any
obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp.
www.bannerengineering.com - tel: 763-544-3164
相关型号：
©2020 ICPDF网 联系我们和版权申明