OPA4336EA/2K5 [BB]
SINGLE-SUPPLY, microPower CMOS OPERATIONAL AMPLIFIERS microAmplifier Series; 单电源，微功耗CMOS运算放大器MicroAmplifier系列
| 型号： | OPA4336EA/2K5 |
| 厂家： | 
BURR-BROWN CORPORATION |
| 描述： | SINGLE-SUPPLY, microPower CMOS OPERATIONAL AMPLIFIERS microAmplifier Series |
| 文件： | 总17页 (文件大小：619K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
O
OPA336
OPA2336
OPA4336
P
A
4
3
3
6
O
P
A
3
3
6
O
P
A
2
3
3
6
SBOS068B – JANUARY 1997 – REVISED APRIL 2004
SINGLE-SUPPLY, microPower
CMOS OPERATIONAL AMPLIFIERS
™
microAmplifier Series
FEATURES
DESCRIPTION
ꢀ SINGLE-SUPPLY OPERATION
OPA336 series microPower CMOS operational amplifiers
are designed for battery-powered applications. They
operate on a single supply with operation as low as 2.1V.
The output is rail-to-rail and swings to within 3mV of the
supplies with a 100kΩ load. The common-mode range
extends to the negative supply—ideal for single-supply
applications. Single, dual, and quad versions have identical
specifications for maximum design flexibility.
ꢀ RAIL-TO-RAIL OUTPUT (within 3mV)
ꢀ microPOWER: IQ = 20µA/Amplifier
ꢀ microSIZE PACKAGES
ꢀ LOW OFFSET VOLTAGE: 125µV max
ꢀ SPECIFIED FROM VS = 2.3V to 5.5V
ꢀ SINGLE, DUAL, AND QUAD VERSIONS
In addition to small size and low quiescent current
(20µA/amplifier), they feature low offset voltage
(125µV max), low input bias current (1pA), and high open-
loop gain (115dB). Dual and quad designs feature
completely independent circuitry for lowest crosstalk and
freedom from interaction.
APPLICATIONS
ꢀ BATTERY-POWERED INSTRUMENTS
ꢀ PORTABLE DEVICES
ꢀ HIGH-IMPEDANCE APPLICATIONS
ꢀ PHOTODIODE PRE-AMPS
ꢀ PRECISION INTEGRATORS
ꢀ MEDICAL INSTRUMENTS
ꢀ TEST EQUIPMENT
OPA336 packages are the tiny SOT23-5 surface mount
and SO-8 surface-mount. OPA2336 come in the miniature
MSOP-8 surface-mount, SO-8 surface-mount, and DIP-8
packages. The OPA4336 package is the space-saving
SSOP-16 surface-mount. All are specified from
–40°C to +85°C and operate from –55°C to +125°C.
A macromodel is available for download (at www.ti.com)
for design analysis.
OPA336
Out
V–
1
2
3
5
4
V+
OPA4336
Out A
–In A
+In A
V+
1
2
3
4
5
6
7
8
16 Out D
15 –In D
14 +In D
13 V–
+In
–In
A
B
D
C
SOT23-5
OPA2336
OPA336
Out A
1
2
3
4
8
7
6
5
V+
NC
–In
+In
V–
1
2
3
4
8
7
6
5
NC
V+
+In B
–In B
Out B
NC
12 +In C
11 –In C
10 Out C
A
–In A
+In A
V–
Out B
–In B
+In B
B
Output
NC
9
NC
DIP-8, SO-8, MSOP-8
SO-8
SSOP-16
NC = No Connection
NC = No Connection
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Copyright © 1997-2004, Texas Instruments Incorporated
www.ti.com
PACKAGE/ORDERING INFORMATION(1)
PACKAGE
DRAWING
DESIGNATOR
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER(1)
TRANSPORT
MEDIA, QUANTITY
PRODUCT
PACKAGE-LEAD
Single
OPA336N
"
SOT23-5
DBV
"
–40°C to +85°C
A36(2)
"
OPA336N/250
OPA336N/3K
Tape and Reel, 250
Tape and Reel, 3000
"
"
OPA336NA
SOT23-5
DBV
"
–40°C to +85°C
A36(2)
"
OPA336NA/250
OPA336NA/3K
Tape and Reel, 250
Tape and Reel, 3000
"
"
"
OPA336NJ
SOT23-5
DBV
"
–40°C to +85°C
J36
"
OPA336NJ/250
OPA336NJ/3K
Tape and Reel, 250
Tape and Reel, 3000
"
"
"
OPA336U
SO-8 Surface-Mount
D
–40°C to +85°C
OPA336U
OPA336U
Rails(3), 100
"
"
"
"
"
OPA336U/2K5
Tape and Reel, 2500
OPA336UA
SO-8 Surface-Mount
D
–40°C to +85°C
OPA336UA
OPA336UA
Rails(3), 100
"
"
"
"
"
OPA336UA/2K5
Tape and Reel, 2500
OPA336UJ(4)
SO-8 Surface-Mount
D
–40°C to +85°C
OPA336UJ
OPA336UJ
Rails(3), 100
"
"
"
"
"
OPA336UJ/2K5
Tape and Reel, 2500
Dual
OPA2336E
"
MSOP-8 Surface-Mount
"
DGK
"
–40°C to +85°C
B36(2)
"
OPA2336E/250
OPA2336E/2K5
Tape and Reel, 250
Tape and Reel, 2500
"
OPA2336EA
"
MSOP-8 Surface-Mount
"
DGK
"
–40°C to +85°C
B36(2)
"
OPA2336EA/250
OPA2336EA/2K5
Tape and Reel, 250
Tape and Reel, 2500
"
OPA2336P
DIP-8
DIP-8
P
P
–40°C to +85°C
–40°C to +85°C
OPA2336P
OPA2336P
Rails, 50
Rails, 50
OPA2336PA
OPA2336PA
OPA2336PA
OPA2336U
"
SO-8 Surface-Mount
"
D
"
"
"
OPA2336U
"
OPA2336U
OPA2336U/2K5
Rails(3), 100
Tape and Reel, 2500
OPA2336UA
"
SO-8 Surface-Mount
"
D
"
–40°C to +85°C
OPA2336UA
"
OPA2336UA
OPA2336UA/2K5
Rails(3), 100
Tape and Reel, 2500
"
Quad
OPA4336EA
"
SSOP-16 Surface-Mount
"
DBQ
"
–40°C to +85°C
OPA4336EA
"
OPA4336EA/250
OPA4336EA/2K5
Tape and Reel, 250
Tape and Reel, 2500
"
NOTES: (1) For the most current package and ordering information, see the package option addendum at the end of this data sheet. (2) Grade will be marked on
the Reel. (3) SO-8 models also available in Tape and Reel. (4) Available Q2, 2004.
ABSOLUTE MAXIMUM RATINGS(1)
ELECTROSTATIC
DISCHARGE SENSITIVITY
Supply Voltage ................................................................................... 7.5V
Signal Input Terminals, Voltage(2) .....................(V–) –0.3V to (V+) +0.3V
Current(2) .................................................... 10mA
This integrated circuit can be damaged by ESD. Texas
Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper han-
dling and installation procedures can cause damage.
Output Short-Circuit(3) .............................................................. Continuous
Operating Temperature ..................................................–55°C to +125°C
Storage Temperature .....................................................–55°C to +125°C
Junction Temperature ...................................................................... 150°C
Lead Temperature (soldering, 10s)................................................. 300°C
ESD damage can range from subtle performance degrada-
tion to complete device failure. Precision integrated circuits
may be more susceptible to damage because very small
parametric changes could cause the device not to meet its
published specifications.
NOTES: (1) Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only. Functional opera-
tion of the device at these conditions, or beyond the specified operating
conditions, is not implied. (2) Input terminals are diode-clamped to the power
supply rails. Input signals that can swing more than 0.3V beyond the supply
rails should be current-limited to 10mA or less. (3) Short-circuit to ground,
one amplifier per package.
OPA336, 2336, 4336
2
SBOS068B
www.ti.com
ELECTRICAL CHARACTERISTICS: VS = 2.3V to 5.5V
Boldface limits apply over the specified temperature range, TA = –40°C to +85°C.
At TA = +25°C, VS = +5V, and RL = 25kΩ connected to VS/2, unless otherwise noted.
OPA336NA, UA
OPA336N, U
OPA2336E, P, U
OPA2336EA, PA, UA
OPA4336EA
OPA336NJ, UJ
PARAMETER
CONDITION
MIN
TYP(1) MAX
MIN
TYP MAX MIN TYP MAX UNITS
OFFSET VOLTAGE
Input Offset Voltage
vs Temperature
vs Power Supply
Over Temperature
Channel Separation, dc
VOS
dVOS/dT
PSRR
±60
±1.5
25
±125
ꢀ
ꢀ
ꢀ
±500
±500 ±2500
ꢀ
µV
µV/°C
µV/V
µV/V
µV/V
VS = 2.3V to 5.5V
VS = 2.3V to 5.5V
100
130
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
0.1
ꢀ
ꢀ
INPUT BIAS CURRENT
Input Bias Current
Over Temperature
Input Offset Current
IB
±1
±1
±10
±60
±10
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
pA
pA
pA
IOS
NOISE
Input Voltage Noise, f = 0.1 to 10Hz
Input Voltage Noise Density, f = 1kHz en
Current Noise Density, f = 1kHz
3
40
30
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
µVp-p
nV/√Hz
fA/√Hz
in
INPUT VOLTAGE RANGE
Common-Mode Voltage Range
Common-Mode Rejection Ratio CMRR
Over Temperature
VCM
–0.2
80
76
(V+) –1
ꢀ
76
74
ꢀ
ꢀ
76
74
ꢀ
V
dB
dB
–0.2V < VCM < (V+) –1V
–0.2V < VCM < (V+) –1V
90
86
86
INPUT IMPEDANCE
Differential
Common-Mode
1013 || 2
1013 || 4
ꢀ
ꢀ
ꢀ
ꢀ
Ω || pF
Ω || pF
OPEN-LOOP GAIN
Open-Loop Voltage Gain
Over Temperature
AOL RL = 25kΩ, 100mV < VO < (V+) – 100mV 100
RL = 25kΩ, 100mV < VO < (V+) – 100mV 100
115
106
90
90
ꢀ
ꢀ
ꢀ
ꢀ
90
90
ꢀ
ꢀ
ꢀ
ꢀ
dB
dB
dB
dB
RL = 5kΩ, 500mV < VO < (V+) – 500mV
RL = 5kΩ, 500mV < VO < (V+) – 500mV
90
90
Over Temperature
FREQUENCY RESPONSE
Gain-Bandwidth Product
Slew Rate
GBW
SR
VS = 5V, G = 1
VS = 5V, G = 1
VIN • G = VS
100
0.03
100
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
kHz
V/µs
µs
Overload Recovery Time
OUTPUT
Voltage Output Swing from Rail(2)
RL = 100kΩ, AOL ≥ 70dB
RL = 25kΩ, AOL ≥ 90dB
RL = 25kΩ, AOL ≥ 90dB
RL = 5kΩ, AOL ≥ 90dB
RL = 5kΩ, AOL ≥ 90dB
3
20
ꢀ
ꢀ
ꢀ
ꢀ
mV
mV
mV
mV
mV
mA
pF
100
100
500
500
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Over Temperature
70
ꢀ
ꢀ
Over Temperature
Short-Circuit Current
Capacitive Load Drive
ISC
CLOAD
±5
See Text
ꢀ
ꢀ
ꢀ
ꢀ
POWER SUPPLY
Specified Voltage Range
Minimum Operating Voltage
Quiescent Current (per amplifier)
Over Temperature
VS
IQ
2.3
5.5
ꢀ
ꢀ
ꢀ
ꢀ
V
V
µA
µA
2.1
20
ꢀ
ꢀ
ꢀ
23
IO = 0
32
36
ꢀ
ꢀ
38
42
IO = 0
TEMPERATURE RANGE
Specified Range
Operating Range
Storage Range
–40
–55
–55
+85
+125
+125
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
°C
°C
°C
Thermal Resistance
SOT-23-5 Surface-Mount
MSOP-8 Surface-Mount
SO-8 Surface-Mount
DIP-8
θJA
200
150
150
100
100
80
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
SSOP-16 Surface-Mount
DIP-14
ꢀSpecifications same as OPA2336E, P, U.
NOTES: (1) VS = +5V. (2) Output voltage swings are measured between the output and positive and negative power-supply rails.
OPA336, 2336, 4336
3
SBOS068B
www.ti.com
TYPICAL CHARACTERISTICS
At TA = +25°C, VS = +5V, and RL = 25kΩ connected to VS/2, unless otherwise noted.
POWER-SUPPLY and COMMON-MODE
REJECTION RATIO vs FREQUENCY
OPEN-LOOP GAIN/PHASE vs FREQUENCY
100
100
80
60
40
20
0
CMRR
G
80
60
40
20
0
0
–45
–90
–135
–180
PSRR
Φ
–20
1
10
100
1k
10k
100k
1M
1
10
100
1k
10k
100k
Frequency (Hz)
Frequency (Hz)
QUIESCENT CURRENT vs SUPPLY VOLTAGE
Per Amplifier
QUIESCENT CURRENT vs TEMPERATURE
Per Amplifier
30
25
20
15
10
30
25
20
15
10
5
VS = +5V
VS = +2.3V
0
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
–75
–50
–25
0
25
50
75
100
125
Supply Voltage (V)
Temperature (°C)
SHORT-CIRCUIT CURRENT vs SUPPLY VOLTAGE
SHORT-CIRCUIT CURRENT vs TEMPERATURE
±6
±5
±4
±3
±2
±1
0
8
7
6
5
4
3
2
1
0
VS = +5V
–ISC
+ISC
+ISC
+ISC
VS = +2.3V
–ISC
–ISC
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
–75
–50
–25
0
25
50
75
100
125
Supply Voltage (V)
Temperature (°C)
OPA336, 2336, 4336
4
SBOS068B
www.ti.com
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VS = +5V, and RL = 25kΩ connected to VS/2, unless otherwise noted.
INPUT VOLTAGE AND CURRENT NOISE
SPECTRAL DENSITY vs FREQUENCY
CHANNEL SEPARATION vs FREQUENCY
1k
100
10
1k
150
140
130
120
110
Voltage Noise
100
10
Dual and Quad devices, G = 1, all
channels. Quad measured channel A
to D or B to C—other combinations
yield improved rejection.
Current Noise
1
1
10
100
1k
10k
100k
100
1k
10k
100k
Frequency (Hz)
Frequency (Hz)
AOL, CMRR, PSRR vs TEMPERATURE
AOL
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
VS = +5.5V
120
110
100
90
6
5
4
3
2
1
0
PSRR
VS = +2.3V
CMRR
80
70
–75
–50
–25
0
25
50
75
100
125
100
1k
10k
100k
Temperature (°C)
Frequency (Hz)
OFFSET VOLTAGE
PRODUCTION DISTRIBUTION
OFFSET VOLTAGE DRIFT MAGNITUDE
PRODUCTION DISTRIBUTION
25
20
15
10
5
25
20
15
10
5
Typical production
distribution of
packaged units.
Typical production
distribution of
packaged units.
0.3%
0.1%
0.2%
0.1%
0
0
Offset Voltage (µV)
Offset Voltage Drift (µV/°C)
OPA336, 2336, 4336
5
SBOS068B
www.ti.com
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VS = +5V, and RL = 25kΩ connected to VS/2, unless otherwise noted.
INPUT BIAS CURRENT
INPUT BIAS CURRENT vs TEMPERATURE
1k
vs INPUT COMMON-MODE VOLTAGE
4
3
2
1
0
100
10
1
VS = +5V
0.1
–75
–50
–25
0
25
50
75
100
125
0
1
2
3
4
5
Temperature (°C)
Common-Mode Voltage (V)
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
VS = +5V
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
5
–2.5
–2.0
–1.5
–1.0
–0.5
0
VS = ±2.5V
4
3
2
1
0
–55°C
Sourcing
Current
Sinking
Current
+125°C
+25°C
VS = +2.3V
+125°C
+125°C
–55°C
+25°C
–55°C
+25°C
0
1
2
3
4
5
6
7
8
–0
–1
–2
–3
–4
–5
–6
–7
–8
Output Current (mA)
Output Current (mA)
LARGE-SIGNAL STEP RESPONSE
G = 1, CL = 620pF, VS = +5V
SMALL-SIGNAL STEP RESPONSE
G = 1, CL = 200pF, VS = +5V
200µs/div
50µs/div
OPA336, 2336, 4336
6
SBOS068B
www.ti.com
Normally, input bias current is approximately 1pA. How-
ever, input voltages exceeding the power supplies can
cause excessive current to flow in or out of the input pins.
Momentary voltages greater than the power supply can be
tolerated as long as the current on the input pins is limited
to 10mA. This is easily accomplished with an input resis-
tor, as shown in Figure 2.
APPLICATIONS INFORMATION
OPA336 series op amps are fabricated on a state-of-the-art
0.6 micron CMOS process. They are unity-gain stable and
suitable for a wide range of general-purpose applications.
Power-supply pins should be bypassed with 0.01µF ceramic
capacitors. OPA336 series op amps are protected against
reverse battery voltages.
OPERATING VOLTAGE
+5V
OPA336 series op amps can operate from a +2.1V to +5.5V
single supply with excellent performance. Most behavior
remains unchanged throughout the full operating voltage
range. Parameters which vary significantly with operating
voltage are shown in the typical characteristics. OPA336
series op amps are fully specified for operation from +2.3V
to +5.5V; a single limit applies over the supply range. In
addition, many parameters are guaranteed over the specified
temperature range, –40°C to +85°C.
IOVERLOAD
10mA max
VOUT
OPAx336
VIN
5kΩ
FIGURE 2. Input Current Protection for Voltages Exceeding
the Supply Voltage.
CAPACITIVE LOAD AND STABILITY
OPA336 series op amps can drive a wide range of capaci-
tive loads. However, all op amps under certain conditions
may become unstable. Op-amp configuration, gain, and
load value are just a few of the factors to consider when
determining stability.
INPUT VOLTAGE
The input common-mode range of OPA336 series op amps
extends from (V–) – 0.2V to (V+) – 1V. For normal
operation, inputs should be limited to this range. The
absolute maximum input voltage is 300mV beyond the
supplies. Thus, inputs greater than the input
common-mode range but less than maximum input volt-
age, while not valid, will not cause any damage to the op
amp. Furthermore, the inputs may go beyond the power
supplies without phase inversion, as shown in Figure 1,
unlike some other op amps.
When properly configured, OPA336 series op amps can
drive approximately 10,000pF. An op amp in unity-gain
configuration is the most vulnerable to capacitive load. The
capacitive load reacts with the op amp’s output resistance,
along with any additional load resistance, to create a pole in
the response which degrades the phase margin. In unity gain,
OPA336 series op amps perform well with a pure capacitive
load up to about 300pF. Increasing gain enhances the
amplifier’s ability to drive loads beyond this level.
One method of improving capacitive load drive in the
unity-gain configuration is to insert a 50Ω to 100Ω resistor
inside the feedback loop, as shown in Figure 3. This reduces
ringing with large capacitive loads while maintaining DC
6V
VOUT
RS
100Ω
OPAx336
VOUT
0V
VIN
CL
RL
FIGURE 1. No Phase Inversion with Inputs Greater than the
Power-Supply Voltage.
FIGURE 3. Series Resistor in Unity-Gain Configuration
Improves Capacitive Load Drive.
OPA336, 2336, 4336
7
SBOS068B
www.ti.com
accuracy. For example, with RL = 25kΩ, OPA336 series op
amps perform well with capacitive loads in excess of 1000pF,
as shown in Figure 4. Without RS, capacitive load drive is
typically 350pF for these conditions, as shown in Figure 5.
Direct Current (DC) error at the output, however, this error
may be insignificant. For instance, with RL = 100kΩ and
RS = 100Ω, there is only about a 0.1% error at the output.
Figure 5 shows the recommended operating regions for the
OPA336. Decreasing the load resistance generally improves
capacitive load drive. Figure 5 also illustrates how stability
differs depending on where the resistive load is connected.
With G = +1 and RL = 10kΩ connected to VS/2, the OPA336
can typically drive 500pF. Connecting the same load to
ground improves capacitive load drive to 1000pF.
RS = 100Ω, Load = 2kΩ || 1000pF, VS = +5V
10k
Operation Above Selected Gain
Curve Not Recommended
G = +2
G = +1
RL to Ground
RL to Ground
1k
50µs/div
FIGURE 4. Small-Signal Step Response Using Series Re-
sistor to Improve Capacitive Load Drive.
G = +1
L to VS/2
R
VS = +5V, VO = VS/2
Alternatively, the resistor may be connected in series with
the output outside of the feedback loop. However, if there is
a resistive load parallel to the capacitive load, it and the
series resistor create a voltage divider. This introduces a
100
5
10
100
Resistive Load (kΩ)
FIGURE 5. Stability—Capacitive Load vs Resistive Load.
OPA336, 2336, 4336
8
SBOS068B
www.ti.com
PACKAGE OPTION ADDENDUM
www.ti.com
9-Dec-2004
PACKAGING INFORMATION
Orderable Device
Status (1)
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
MSOP
MSOP
MSOP
MSOP
PDIP
Drawing
DGK
DGK
DGK
DGK
P
OPA2336E/250
OPA2336E/2K5
OPA2336EA/250
OPA2336EA/2K5
OPA2336P
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
OBSOLETE
OBSOLETE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
PREVIEW
PREVIEW
ACTIVE
8
8
8
8
8
8
8
8
8
8
5
5
5
5
5
5
8
8
8
8
8
8
8
8
16
250
2500
250
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
CU NIPDAU Level-1-235C-UNLIM
CU NIPDAU Level-1-235C-UNLIM
CU NIPDAU Level-1-235C-UNLIM
CU NIPDAU Level-1-235C-UNLIM
2500
50
Call TI
Level-NA-NA-NA
OPA2336PA
PDIP
P
50
Call TI
Level-NA-NA-NA
OPA2336U
SOIC
D
100
CU SNPB
CU SNPB
CU SNPB
CU SNPB
Level-2-220C-1 YEAR
Level-2-220C-1 YEAR
Level-2-220C-1 YEAR
Level-2-220C-1 YEAR
OPA2336U/2K5
OPA2336UA
SOIC
D
2500
100
SOIC
D
OPA2336UA/2K5
OPA336N/250
OPA336N/3K
OPA336NA/250
OPA336NA/3K
OPA336NJ/250
OPA336NJ/3K
OPA336P
SOIC
D
2500
250
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
PDIP
DBV
DBV
DBV
DBV
DBV
DBV
P
CU NIPDAU Level-1-235C-UNLIM
CU NIPDAU Level-1-235C-UNLIM
CU NIPDAU Level-1-235C-UNLIM
CU NIPDAU Level-1-235C-UNLIM
CU NIPDAU Level-3-220C-168 HR
CU NIPDAU Level-3-220C-168 HR
3000
250
3000
250
3000
Call TI
Call TI
Call TI
OPA336PA
PDIP
P
Call TI
OPA336U
SOIC
D
100
2500
100
CU SNPB
CU SNPB
CU SNPB
CU SNPB
Call TI
Level-2-220C-1 YEAR
Level-2-220C-1 YEAR
Level-2-220C-1 YEAR
Level-2-220C-1 YEAR
Call TI
OPA336U/2K5
OPA336UA
SOIC
D
SOIC
D
OPA336UA/2K5
OPA336UJ
SOIC
D
2500
100
SOIC
D
OPA336UJ/2K5
OPA4336EA/250
SOIC
D
2500
250
Call TI
Call TI
SSOP/
QSOP
DBQ
CU NIPDAU Level-3-240C-168 HR
OPA4336EA/2K5
OPA4336PA
ACTIVE
SSOP/
QSOP
DBQ
N
16
14
2500
None
None
CU NIPDAU Level-3-240C-168 HR
OBSOLETE
PDIP
Call TI
Call TI
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional
product content details.
None: Not yet available Lead (Pb-Free).
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens,
including bromine (Br) or antimony (Sb) above 0.1% of total product weight.
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
9-Dec-2004
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
MECHANICAL DATA
MPDI001A – JANUARY 1995 – REVISED JUNE 1999
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE
0.400 (10,60)
0.355 (9,02)
8
5
0.260 (6,60)
0.240 (6,10)
1
4
0.070 (1,78) MAX
0.325 (8,26)
0.300 (7,62)
0.020 (0,51) MIN
0.015 (0,38)
Gage Plane
0.200 (5,08) MAX
Seating Plane
0.010 (0,25) NOM
0.125 (3,18) MIN
0.100 (2,54)
0.021 (0,53)
0.430 (10,92)
MAX
0.010 (0,25)
M
0.015 (0,38)
4040082/D 05/98
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢂꢃꢄ ꢅꢆꢂ ꢄꢇ ꢈ ꢄꢉꢄ
MSOI004E JANUARY 1995 − REVISED MAY 2002
DBQ (R−PDSO−G**)
PLASTIC SMALL−OUTLINE PACKAGE
0.012 (0,30)
0.008 (0,20)
0.025 (0,64)
24
0.005 (0,13)
13
0.157 (3,99) 0.244 (6,20)
0.150 (3,81) 0.228 (5,80)
0.008 (0,20) NOM
Gauge Plane
1
12
A
0.010 (0,25)
0°−8°
0.035 (0,89)
0.016 (0,40)
0.069 (1,75) MAX
Seating Plane
0.004 (0,10)
0.010 (0,25)
0.004 (0,10)
PINS **
16
20
24
28
DIM
0.197
(5,00)
0.344
(8,74)
0.344
(8,74)
0.394
(10,01)
A MAX
A MIN
0.189
(4,80)
0.337
(8,56)
0.337
(8,56)
0.386
(9,80)
M0−137
VARIATION
D
AB
AD
AE
AF
4073301/F 02/2002
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15).
D. Falls within JEDEC MO−137.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
Digital Control
Military
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
Logic
interface.ti.com
logic.ti.com
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
microcontroller.ti.com
Telephony
Video & Imaging
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2004, Texas Instruments Incorporated
相关型号：
OPA4336EA/2K5G4
SINGLE-SUPPLY, microPower CMOS OPERATIONAL AMPLIFIERS CMOS OPERATIONAL AMPLIFIERS
BB
©2020 ICPDF网 联系我们和版权申明