BYH05-100S02 [BELLNIX]
Ultra small size, Adjustable output voltage type high voltage power supply 0.2W Mid-high voltage DC-DC converter;型号: | BYH05-100S02 |
厂家: | Bellnix |
描述: | Ultra small size, Adjustable output voltage type high voltage power supply 0.2W Mid-high voltage DC-DC converter |
文件: | 总4页 (文件大小:252K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
small size, Adjustable output voltage type high voltage power supply
0.2W Mid-high voltage DC-DC converter
0V to 100V, 0V to 200V BYH Series
The BYH series is an ultra small type mid-high voltage DC-DC converter which has stored 0 to 100V and 0 to 200V in a 24pin-IC.
Using the latest SMT (surface mount technology), the high voltage technology is now 1/3 to 1/4 of the original product.
■ Features
・Achieved 24pin-IC size
・5 sided metallic shield
・Output voltage 0 to 100V and 0 to 200・Low ripple noise of 10mVp-p
・Output capacity 0.2W
・Over current protection
・Bar in tests 100% conducted
・Adjustable voltage with external voltage
・Worlds ultra small size, device achieve・Isolation withhold between P-S, DC250V
・Low cost
・High reliability and long life
■ Model/rating
Output
current
(mA)
Output
capacity
(W)
Adjustable output
voltage
(Vdc) (note 1)
Case
Input current
(mA) typ
Ripple noise
(mVp-p) typ
Input voltage Output voltage
(Vdc)
(Vdc)
BYH series
BYH05-100S02
BYH12-100S02
BYH05-200S01
BYH12-200S01
0
0
0
0
~
~
~
~
2
2
1
1
90
34
98
41
10
10
10
10
Y
Y
Y
Y
4.75
~
~
~
~
5.25
100
±
±
±
±
4%
0
0
0
0
~
~
~
~
100
100
200
200
0.2
0.2
0.2
0.2
11.0
4.75
11.0
16.0
5.25
16.0
100
200
200
4%
4%
4%
■ Specifications
Input fluctuation
Load fluctuation
Temp fluctuation
0.3
%
typ.(Input voltage:+4.75V
typ.(Load current fluctuation from 0%
0.5 typ.(Temp. fluctuation from -10℃~+50
Droop type characteristic, auto restart circuit activates at 105% or more
Below 4%(Rated output, rated load, and the Vcont 3.0V or 10.0V)
BYH05 series : Exxternal voltage controlled with 0V +3V
BYH12 series : External voltage controlled with 0V +10V
and higher)
~
+5.25V or to fluxation +11.0V
100%)
.)
~
+16.0V
8%
~
±
%
℃
Over current protection
Output voltage accuracy
Output voltage control (1)
Output voltage control (2)
Usage temp range
±
~
~
-10℃~+60
℃
(Temp derating required for 50℃
Storage temp range
Usage humidity range
Isolation withhold
-25℃~+85
℃
20%
Between primary and secondary DC250V 1 min. (continuous withhold : DC250V)
Between primary and secondary also between case DC500V 100M min.
~95%RH( no dewing)
Isolation resistance
Ω
Floating output
ꢀ ꢀ
Floating output until voltage DC250V. Therefore either the minus or plus can be in contact.
1,400,000H min.(Calclulated using the Bellnix MTBF calculation graph
MTBF anticipated value
ꢀ ꢀ ꢀ ꢀ ꢀ
Note 1: The output voltage is controlled by the Vcont voltage being impressed. Connect an external voltage to impress to the
the Vcont pin to control the output voltage. When Vcont voltage =0V, the output voltage (output residual voltage) must be
within 0.5% of the max output voltage (when input/output is rated)
■ Test curcuit
■ Block diagram
13
12
24
22
1
+Vin
+Vout
-Vout
+Vout
+Vin
DC-AC
Vcont
+
switch circuit
24
13
High voltage
oscillation
+
E1
BYH
Commutation
flatness
E2
+
Trance
E1
E2
Output control
-Vin
Over current
protection
-Vin
12
10KΩ
1
-Vout
(Isolation)
Vcont
22
External
voltage
BYH05 series : E1=4.75V~5.25V、E2=0V~3V
BYH12 series : E1=11.0V~16.0V、E2=0V~10V
Voltage detection circuit
1
BHV20110405
■ Model/Dimensions/Pin Configuration (Y case)
N.P
2.0
2.54
Φ0.6
22.86
Units:mm (1/1)
Pin
Feature
1
12
13
-Vin
1
12 -Vout
13 +Vout
22 Vcont
24 +Vin
24 22
2.33
2.33
5.08
22.86
32.6
Weight : 14g typ.
Units : mm
■ Standard usage
■ Over current protection
The BYH series has an over current protection to protect against
over load and load shortage. When over load or load shoratage
occurs, if the output voltage is lowered an activated, and the
reason has been removed, the output will auto recover.
13
12
24
22
+Vout
+Vin
Vcont
+
E1
C1
Load
BYH
E2
1
100
Vout
-Vin
100% output
80
60
The BYH series does not need any external parts, however
the longer the power supply and converter distance is, and
thinner the input line is to the input filter, the higher the impedance
will be, and connected a capacitor to CI is recommended.
As long as the capacitor is connected, the design should be
the converter's side lead inductance is lowered.
50% output
40
20
0
(%)
0
100%
Output current (lo)
Over current protection characteristic
Bellnix High Voltage DC-DC Converters
2
BHV20110405
■ Setting output voltage/adjusting information
The BYH series output voltage can be adjusted using an
external voltage.
BYH05-200S01
Load=Open
100%
80%
60%
40%
20%
0%
13
12
24
22
+Vout
-Vout
+Vin
Vcont
+
E1
C1
Load
BYH
E2
Load=200K
Ω
1
-Vin
ꢀ ꢀ
0V
1V
2V
3V
4V
5V
Output control voltage
BYH05-100S02
Load=Open
BYH12-200S01
100%
80%
60%
40%
20%
0%
100%
80%
60%
40%
20%
0%
Load=Open
Load=50K
Ω
Load=200K
Ω
ꢀ ꢀ
0V
1V
2V
3V
4V
5V
0V
2V
4V
6V
8V
10V
Output control voltage
Output control voltage
BYH12-100S02
Load=Open
■ Recommended pattern
100%
80%
60%
40%
20%
0%
5.08
22.86
(Seen from the parts surface)
Load=50KΩ
0V
2V
4V
6V
8V
10V
Diameter: φ1.0~1.2
27.94
Output control voltage
●The voltage impressed on Vcont should not exceed
●(Vcont+11%)
1) The BYH series uses a metallic case. When using a double
mounting PCB, the wiring to the converter should be done on
the soldering surface. Also, this converter will have a high voltage
so make sure to create enough creepage distance.
●Connect the external control voltage common to the
-Vin (1pin).
●The fluctuation rate and ripple noise of Vcont pin will be
When using a double mounting PCB, make the high voltage output
pin's surface as small as possible.
2)
determined by the output.
The metallic case does not need to be in contact with anything else.
However, if you would like to bring the metallic case into contact, it
should be used to lower the anti ground impedance.
3)
3
BHV20110405
BYH Series
■ Temp derating
■ When lowering the output noise even more
When using the product where the ambient temp is
higher than 50℃, follow the derating graph below.
Increase the load resistor as the temp increases.
The BYH series does need any external parts, however
to lower the output noise even farther, connect a
capacitor C2 like the figure below.
The product may start up in this area, however reliablity is not
insured.
100
24
22
1
13
+Vout
+Vin
Vcont
+
80
60
40
BYH
E1
C1
Load
C2
12
E2
-Vin
-Vout
C1=22~47μF
C2=0.047~0.1μF
20
(%)
When lowering the output noise eve more, keep in mind the
input/output wiring, creepage and area distance, while
keeping the wiring as thin as possible and the C2 near
the Load in the layout.
0
-20 -10
0
+10 +20 +30 +40 +50 +60
Ambient temp(
℃)
■ Preventing inverse connections
Points!
The converter may break if the polarities are reversed.
If there is a possibility in which the connections maybe
reversed, connect a diode and fuse like below.
1) When choosing a capacitor, choose one which is a
high frequency characteristic capacitor.
2) Earth (COMMON) line should be bundled and kept small
Fuse
+Vin
while the wiring pattern is thick and short.
+
3) The capacitor which is connected to the output side should
be able to withhold the pressure, and connected to the load side.
At this time, the capacitor lead should be shortened. Also,
when the load response time is a problem, please be aware
of the time constant.
12V
BYH
-Vin
■ Recommended solder conditions
Soldering conditions for each part is as follows:
1) Using a soldering iron
2) Using a soldering tub
340~360℃
230~260℃
5 sec.
10 sec.
■ About washing the product
This product can not be washed as a whole. However, when
there is a need to wash the product, use an IPA to wash
only the soldered surface with a hand brush.
4
Bellnix High Voltage DC-DC Converters
BHV20110405
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明