HBD040YED-A3V [BEL]

DC-DC Regulated Power Supply Module, 2 Output, 60W, Hybrid;


型号：	HBD040YED-A3V
厂家：	BEL FUSE INC.
描述：	DC-DC Regulated Power Supply Module, 2 Output, 60W, Hybrid
文件：	总3页 (文件大小：94K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

ꢀꢀ

(888) IPD-CONVerters

ꢀ

(888) 473-2668

ꢀ

www.ipdconverters.com

HBD SERIES - DUAL OUTPUT, 60 WATT

FEATURES

DESCRIPTION

HBD dual output, DC/DC converters feature high

efficiency, 1500 VDC isolation, and open-frame

packaging. The HBD family allows board designers

to deliver any combination of power from

either output, up to each model’s maximum rating.

The HBD is available in 5V/3.3V or 3.3V/2.5V

combinations in either a 24V or 48V input version. The

HBD uses planar magnetics and has an MTBF of over a

million hours.

• Independent Dual Outputs • Independent Trim

• Flexible Load Sharing

For Each Output

• High Efficiency Topology • 1500V Isolation

• Open-Frame Design

• Planar Magnetics

• 100°C Baseplate

Operation

Efficiency vs. Load (24V Input)

HBD060YGE-A

EFF. (18V)

EFF. (24V)

EFF. (36V)

TECHNICAL SPECIFICATIONS

Input

Voltage Range

100

24 VDC Nominal

48 VDC Nominal

Reflected Ripple

18.00 - 36.00 VDC

34.00 - 75.00 VDC

80 mA

LOAD %

Input Reverse Voltage Protection

Shunt Diode

Efficiency vs. Load (48V Input)

Output

Setpoint Accuracy

±1%

0.2% V_out

1.0% V_out

0.5% V_out

1.0% V_out

Line Regulation V_inMin. - V_inMax., I_outRated, Output 1

Line Regulation V_inMin. - V_inMax., I_outRated, Output 2

Load Regulation I_outMin. - I_outMax., V_inNom., Output 1

Load Regulation I_outMin. - I_outMax., V_inNom., Output2

Minimum Output Current

10% I_outRated

HBD060ZGE-A

HBD040ZGE-A

HBD040ZED-A

Dynamic Regulation, Loadstep

Pk Deviation

25% I_out

4% V_out

500 µs

Settling Time

Voltage Trim Range (5V/3.3V Units)

Power Limit Threshold Range, % of I_outRated

OVP Trip Range (Main Ouput)

±10%

110 - 140%

115 - 140% V_outNom.

100

LOAD %

General

Turn-On Time

10 ms

Positive Logic

500 kHz

Notes

For negative logic, add suffix “N” to model number.

Remote Shutdown

Switching Frequency

Isolation

Input - Output

Input - Case

†

1500 VDC

1050 VDC

500 VDC

0.03%/°C

MTBF predictions may vary slightly from model to model.

Output - Case

Specifications typically at 25°C, normal line, and full load, unless otherwise

stated.

Temperature Coefficient

Case Temperature

Operating Range

-40 To +100°C

-40 To +125°C

105 To 115°C

95%

Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with

commercial wave-soldering equipment.

Storage Range

Thermal Shutdown Range

Humidity Max., Non-Condensing

Vibration, 3 Axes, 5 Min Each

Safety: Agency approvals may vary from model to model. Please consult factory

for specific model information.

5 g

MTBF (Bellcore TR-NWT-000332)

1.3 x 10⁶Hrs

UL, CUL, VDE

2.4 oz

†

Units are water-washable and fully compatible with commercial spray or

immersion post wave-solder washing equipment.

Safety

Weight (approx.)

HBD SERIES - DUAL OUTPUT, 60 WATT

MODELS - (See the last page of this file for options.)

Vin

(Volts)

Vin Range

(Volts)

Iin Max.*

(Amps)

Vout

(Volts)

Iout Rated

(Amps)

Ripple & Noise

Pk-Pk (mV)

Efficiency

Typ. **

Model

18 - 36

34 - 75

2.89

4.54

3.02

1.51

1.62

2.27

3.3/2.5

5.0/3.3

3.3/2.5

5.0/3.3

12/15

8/12

12/15

75/75

100/75

75/75

75%

78%

80%

75%

79%

HBD040YED-A

HBD060YGE-A

HBD040YGE-A

HBD040ZGE-A

HBD040ZED-A

HBD060ZGE-A

100/75

Denotes advanced product release. Consult factory for product availability.

* Maximum input current at minimum input voltage, maximum rated output power.

** At nominal Vin, rated output.

Note: Current can be drawn from either output to its maximum value, or from both outputs to a combined total of 15A.

MECHANICAL DRAWING

Function

Tolerances

(Millim

Thermal Impedance

-V_in

Case

On/Off

Inches:

eters)

Natural Convection

6.6 °C/W

5.7 °C/W

4.2 °C/W

3.1 °C/W

2.6 °C/W

.XX ± 0.020

.XXX ± 0.010

.X ± 0.5

.XX ± 0.25

100 LFM

200 LFM

300 LFM

400 LFM

+V_in

+V_{out 2}

Pin:

± 0.002

- V_{out 2}

Trim 2

+V_{out 1}

± 0.05

Note:

Thermal impedance data is dependent on

many environmental factors. The exact

thermal performance should be validated for

specific application.

(Dimensions as listed unless otherwise

specified.)

-V_out

Trim 1

OPTIONS

When ordering equipment options, use the following suffix information. Select the option(s) that

you prefer and add them to the model number. Example ordering options are located below the

options table.

OPTION

Negative Logic

SUFFIX

APPLICABLE SERIES

REMARKS

HAS, HBD, HBS, HES, LES, QBS,

QES, TES, TQD

TTL “Low” Turns Module ON

TTL “High” Turns Module OFF

Lucent Compatible Trim

Terminal Strip

Trim

HAS, HBD, HBS, HES, QBS, QES

XWS, XWD, XWT

IAS, LES

Enable

IAD, IAS, LES, SMS

IAS, LES

Trim and Enable

Current Share

Headerless

SMS

Encapsulated EWS, IWS, OWS

PIN LENGTH AND HEATSINK

OPTIONS

Standard Pin Length is 0.180”

(4.6mm)

0.110” (2.8mm) Pin Length

0.150” (3.8mm) Pin Length

0.24” (6.1mm) Horizontal Heatsink

All Units (Except SMS)

All Units (Except DIP, SIP, and SM

Packages)

Includes Thermal Pad

0.24” (6.1mm) Vertical Heatsink

All Units (Except DIP, SIP, and SM

Packages)

0.45” (11.4mm) Horizontal

Heatsink

All Units (Except DIP, SIP, and SM

Packages)

0.45” (11.4mm) Vertical Heatsink

All Units (Except DIP, SIP, and SM

Packages)

0.95” (24.1mm) Horizontal

Heatsink

All Units (Except DIP, SIP, and SM

Packages)

0.95” (24.1mm) Vertical Heatsink

All Units (Except DIP, SIP, and SM

Packages)

Example Options:HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and

0.95” vertical heatsink.

LES015YJ-3N = LES015YJ with optional trim and enable, negative logic.

QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110” pin length.

NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems,

equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc.

TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the

date manufactured. Specifications are subject to change without notice.

相关型号：