HBD040YED-AN83H [BEL]

DC-DC Regulated Power Supply Module, 2 Output, 60W, Hybrid;


型号：	HBD040YED-AN83H
厂家：	BEL FUSE INC.
描述：	DC-DC Regulated Power Supply Module, 2 Output, 60W, Hybrid
文件：	总3页 (文件大小：200K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

HBD DC/DC Series Data Sheet

60-Watt, Dual Output

Features

• Independent Dual Outputs

• Flexible Load Sharing

• High Efficiency Topology

• Open-Frame Design

• Planar Magnetics

• Independent Trim For Each Output

• 1500V Isolation

• 100°C Baseplate Operation

Description

HBD dual output, DC/DC converters feature high efficiency, 1500 VDC isolation, and open-frame packaging. The HBD

family allows board designers to deliver any combination of power from either output, up to each model’s maximum

rating. The HBD is available in 5V/3.3V or 3.3V/2.5V combinations in either a 24V or 48V input version. The HBD uses

planar magnetics and has an MTBF of over a million hours.

Efficiency vs. Load (24V Input)

Technical Specifications

Input

Voltage Range

24 VDC Nominal

48 VDC Nominal

18.00 - 36.00 VDC

34.00 - 75.00 VDC

HBD060YGE-A

Reflected Ripple

Input Reverse Voltage Protection

80 mA

Shunt Diode

EFF. (18V)

EFF. (24V)

EFF. (36V)

LOAD %

100

Output

Setpoint Accuracy

±1%

Efficiency vs. Load (48V Input)

Line Regulation V Min. - V Max., I

Rated, Output 1

Rated, Output 2

0.2% V

1.0% V

0.5% V

out

Line Regulation V Min. - V Max., I

out

Load Regulation I

Min. - I

Max., V Nom., Output 1

out

Load Regulation I

Min. - I

Max., V Nom., Output2

1.0% V

out

Minimum Output Current

10% I

Rated

25% I

4% V

out

Dynamic Regulation, Loadstep

Pk Deviation

Settling Time

out

500 m s

±10%

HBD060ZGE-A

HBD040ZGE-A

HBD040ZED-A

Voltage Trim Range (5V/3.3V Units)

Power Limit Threshold Range, % of I

OVP Trip Range (Main Ouput)

Rated

110 - 140%

115 - 140% V Nom.

out

100

LOAD %

General

Notes

Turn-On Time

10 ms

Positive Logic

500 kHz

Remote Shutdown

Switching Frequency

Isolation

†

For negative logic, add suffix “N” to model number.

MTBF predictions may vary slightly from model to model.

Input - Output

1500 VDC

1050 VDC

500 VDC

0.03%/°C

Input - Case

Specifications typically at 25°C, normal line, and full load, unless otherwise

stated.

Output - Case

Temperature Coefficient

Case Temperature

Operating Range

Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with

commercial wave-soldering equipment.

-40 To +100°C

-40 To +125°C

105 To 115°C

95%

Storage Range

Thermal Shutdown Range

Humidity Max., Non-Condensing

Vibration, 3 Axes, 5 Min Each

Safety: Agency approvals may vary from model to model. Please consult

factory for specific model information.

5 g

†

MTBF (Bellcore TR-NWT-000332)

1.3 x 10 Hrs

Units are water-washable and fully compatible with commercial spray or

immersion post wave-solder washing equipment.

Safety

Weight (approx.)

UL, cUL, VDE

2.4 oz

REV. SEP 05, 2003

Page 1 of 3

HBD DC/DC Series Data Sheet

60-Watt, Dual Output

Model Selection

INPUT VOLTAGE

RANGE (VOLTS)

MAXIMUM INPUT

CURRENT (AMPS)*

OUTPUT

VOLTAGE (VOLTS)

RATED OUTPUT

CURRENT (AMPS)

RIPPLE & NOISE

pk-pk (mV)

TYPICAL

EFFICIENCY**

MODEL

(VOLTS)

HBD040YED-A

HBD060YGE-A

HBD040YGE-A

HBD040ZGE-A

HBD040ZED-A

HBD060ZGE-A

18-36

34-75

2.89

4.54

3.02

1.51

1.62

2.27

3.3/2.5

5.0/3.3

3.3/2.5

5.0/3.3

12/15

8/12

12/15

75/75

100/75

75/75

75%

78%

80%

75%

75/75

NOTES: * Maximum input current at minimum input voltage, maximum rated output power.

** At nominal V , rated output.

Note: Current can be drawn from either output to its maximum value, or from both outputs to a combined total of 15A.

Mechanical Drawing

Function

-V

Tolerances

(Millimeters)

Case

On/Off

Thermal Impedance

Inches:

.XX ± 0.020

.XXX ± 0.010

Natural Convection

100 LFM

6.6 °C/W

.X ± 0.5

.XX ± 0.25

5.7 °C/W

4.2 °C/W

3.1 °C/W

2.6 °C/W

200 LFM

out 2

300 LFM

- V

out 2

Pin:

± 0.002

400 LFM

Trim 2

± 0.05

out 1

Note:

-V

Thermal impedance data is dependent on

many environmental factors. The exact

thermal performance should be validated

for specific application.

(Dimensions as listed unless otherwise

specified.)

out 1

Trim 1

REV. SEP 05, 2003

Page 2 of 3

OPTIONS

This page is offered as a reference. Consult factory for actual availability of options. When ordering equip-

ment options, use the following suffix information. Select preferred option(s) and add the suffix to the model

number. Ordering option examples are located below the options table.

OPTION

Negative Logic

SUFFIX

APPLICABLE SERIES

REMARKS

HAS, HBD, HBS, HES, HLS, HLD, LES,

QBS, QES, QLS, TES, TQD

TTL "Low" Turns Module ON

TTL "High" Turns Module OFF

Lucent-Compatible Trim

HAS, HBD, HBS, HES, HLS, QBS, QES,

QLS

Trim

IAS, LES

Enable

IAD, IAS, LES, SMS

IAS, LES

Trim and Enable

Pin Length and Heatsink Options

0.110" (2.8mm) Pin Length

Standard Pin Length is 0.180" (4.6mm)

All Leaded Models

0.150" (3.8mm) Pin Length

0.24" (6.1mm) Horizontal Heatsink

All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks

(Except HLS, HLD, QLS, TLD, and TKD Packages)

Includes Thermal Pad

0.24" (6.1mm) Vertical Heatsink

0.45" (11.4mm) Horizontal Heatsink

0.45" (11.4mm) Vertical Heatsink

0.95" (24.1mm) Horizontal Heatsink

0.95" (24.1mm) Vertical Heatsink

All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks

(Except HLS, HLD, QLS, TLD, and TKD Packages)

All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks

(Except HLS, HLD, QLS, TLD, and TKD Packages)

All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks

(Except HLS, HLD, QLS, TLD, and TKD Packages)

All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks

(Except HLS, HLD, QLS, TLD, and TKD Packages)

All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks

(Except HLS, HLD, QLS, TLD, and TKD Packages)

Example Options:

HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent-compatible trim, and 0.95” vertical heatsink.

LES015YJ-3N = LES015YJ with optional trim and enable, negative logic.

QBS066ZG-AT8 = QBS066ZG-A with Lucent-compatible trim and 0.110” pin length.

NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not authorized for use as critical components in life support systems, equip-

ment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president of

Power-One, Inc.

TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the

date manufactured. Specifications are subject to change without notice.

REV. SEP 05, 2003

Page 3 of 3

相关型号：