QM48T40033-NBC0 [BEL]
DC-DC Regulated Power Supply Module, 1 Output, 132W, Hybrid, QUARTER BRICK PACKAGE-8;
| 型号： | QM48T40033-NBC0 |
| 厂家： | 
BEL FUSE INC. |
| 描述： | DC-DC Regulated Power Supply Module, 1 Output, 132W, Hybrid, QUARTER BRICK PACKAGE-8 |
| 文件： | 总12页 (文件大小：967K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
The QmaXTM Series of high current single output DC-DC
converters from Bel Power Solutions sets new standards for
thermal performance and power density in the quarter brick
pack-age.
The 40A QM48T converters of the QmaXTM Series provide
thermal performance in high temperature environments that
is comparable to or exceeds the industry’s leading 40A
halfbricks. This is accomplished through the use of patent
pending circuit, packaging and processing techniques to
achieve ultra-high efficiency, excellent thermal manage-
ment and a very low body profile.
RoHS lead-free solder and lead-solder-exempted
products are available
Delivers up to 40 A (132 W)
Industry-standard quarter brick pinout
Higher current capability at 70ºC than most
competitors’ 40 A half-bricks
The QM48T40 converters have a power density of up to 130
W/in3, more than twice that of competitors’ 40A halfbricks.
Over 1 square inch of board space can be saved for every
slot in which a 40A half-brick is replaced with a QM48T40
converter from Bel Power Solutions.
On-board input differential LC-filter
High efficiency – no heat sink required
Start-up into pre-biased output
No minimum load required
Low profile: 0.31” [7.9 mm]
Low weight: 1.06 oz [30 g] typical
Meets Basic Insulation requirements of EN60950
Withstands 100 V input transient for 100 ms
Fixed-frequency operation
Fully protected
Remote output sense
Low body profile and the preclusion of heat sinks minimize
impedance to system airflow, thus enhancing cooling for
downstream devices. The use of 100% automation for
assembly, coupled with Bel Power Solutions advanced
electric and thermal design, results in a product with
extremely high reliability.
Operating from a 36-75 V input, the QmaXTM Series
converters provide standard output voltage for 3.3 V.
Output can be trimmed from –20% to +10% of the nominal
output voltage, thus providing outstanding design flexibility.
Output voltage trim range: +10%/−20% with Industry-
standard trim equations
High reliability: MTBF of 2.6 million hours, calculated
per Telcordia TR-332, Method I Case 1
Positive or negative logic ON/OFF option
UL 60950 recognition in US and Canada and DEMKO
certification per IEC/EN 60950
Meets conducted emissions requirements of FCC
Class B and EN 55022 Class B with external filter
All materials meet UL94, V-0 flammability rating
.
.
.
.
North America
+1-866.513.2839
Asia-Pacific
+86.755.29885888
Europe, Middle East
+353 61 225 977
tech.support@psbel.com
© 2015 Bel Power Solutions, Inc.
BCD.00632_AA
QM48T40033
Conditions: TA = 25 ºC, Airflow = 300 LFM (1.5 m/s), Vin = 48 VDC, unless otherwise specified.
PARAMETER
ABSOLUTE MAXIMUM RATINGS
Input Voltage
NOTES
MIN
TYP
MAX
UNITS
Continuous
0
80
85
VDC
°C
Operating Ambient Temperature
Storage Temperature
-40
-55
125
°C
INPUT CHARACTERISTICS
Operating Input Voltage Range
Input Under Voltage Lockout
Turn-on Threshold
36
48
75
VDC
Non-latching
100 ms
33
31
34
32
35
33
VDC
VDC
VDC
Turn-off Threshold
Input Voltage Transient
ISOLATION CHARACTERISTICS
I/O Isolation
100
2000
10
VDC
nF
Isolation Capacitance
1.4
Isolation Resistance
MΩ
FEATURE CHARACTERISTICS
Switching Frequency
Output Voltage Trim Range1
Remote Sense Compensation1
Output Over-Voltage Protection
Auto-Restart Period
415
kHz
%
Industry-std. equations on page 5
Percent of VOUT(NOM)
-20
+10
+10
140
%
Non-latching
117
128
100
4
%
Applies to all protection features
ms
Turn-On Time
ms
Converter Off
Converter On
Converter Off
Converter On
-20
2.4
2.4
-20
0.8
20
VDC
VDC
VDC
VDC
ON/OFF Control (Positive Logic)
ON/OFF Control (Negative Logic)
20
0.8
INPUT CHARACTERISTICS
Maximum Input Current
40 ADC, 3.3 VDC Out @ 36 VDC In
Vin = 48 V, converter disabled
Vin = 48 V, converter enabled
25MHz bandwidth
4.1
ADC
mADC
mADC
mAPK-PK
dB
Input Stand-by Current
3
Input No Load Current (0 load on the output)
Input Reflected-Ripple Current
Input Voltage Ripple Rejection
OUTPUT CHARACTERISTICS
Output Voltage Set Point (no load)
63
7.5
64
120Hz
3.267
3.250
3.300
±2
3.333
±5
VDC
mV
Over Line
Output Regulation
Over Load
±2
±5
mV
Output Voltage Range
Over line, load and temperature2
Full load + 10 μF tantalum + 1 μF ceramic
Plus full load (resistive)
3.350
50
VDC
mVPK-PK
μF
Output Ripple and Noise - 25MHz bandwidth
External Load Capacitance
Output Current Range
30
40,000
40
0
ADC
ADC
A
Current Limit Inception
Non-latching
42
47
50
10
52
Non-latching. Short=10mΩ.
Non-latching
Peak Short-Circuit Current
RMS Short-Circuit Current
DYNAMIC RESPONSE
60
15
Arms
Load Change 25% of Iout Max, di/dt = 1 A/μS
Setting Time to 1%
Co = 470 μF tantalum + 1 μF ceramic
120
80
mV
µs
866.513.2839
tech.support@psbel.com
© 2015 Bel Power Solutions, Inc.
BCD.00632_AA
QM48T40033
EFFICIENCY
100% Load
50% Load
90.5
92.5
%
%
Additional Notes:
1
Vout can be increased up to 10% via the sense leads or up to 10% via the trim function, however total output voltage trim
from all sources should not exceed 10% of VOUT (NOM), in order to insure specified operation of over-voltage protection circuitry.
2
-40ºC to 85ºC
Input and Output Impedance
These power converters have been designed to be stable with no external capacitors when used in low inductance input and
output circuits.
However, in many applications, the inductance associated with the distribution from the power source to the input of the
converter can affect the stability of the converter. The addition of a 33 µF electrolytic capacitor with an ESR < 1 across the
input helps ensure stability of the converter. In many applications, the user has to use decoupling capacitance at the load.
The power converter will exhibit stable operation with external load capacitance up to 40,000 µF.
ON/OFF (Pin 2)
The ON/OFF pin is used to turn the power converter on or off remotely via a system signal. There are two remote control
options available, positive logic and negative logic and both are referenced to Vin(-). Typical connections are shown in Fig.
A.
TM Series
QmaX
Vin (+)
ON/OFF
Vin (-)
Vout (+)
SENSE (+)
TRIM
Converter
(Top View)
Rload
Vin
SENSE (-)
Vout (-)
CONTROL
INPUT
Fig. A: Circuit configuration for ON/OFF function.
The positive logic version turns on when the ON/OFF pin is at logic high and turns off when at logic low. The converter is on
when the ON/OFF pin is left open.
The negative logic version turns on when the pin is at logic low and turns off when the pin is at logic high. The ON/OFF pin
can be hard wired directly to Vin(-) to enable automatic power up of the converter without the need of an external control
signal.
ON/OFF pin is internally pulled-up to 5 V through a resistor. A mechanical switch, open collector transistor, or FET can be
used to drive the input of the ON/OFF pin. The device must be capable of sinking up to 0.2 mA at a low level voltage of 0.8
V. An external voltage source of ±20 V max. may be connected directly to the ON/OFF input, in which case it should be
capable of sourcing or sinking up to 1 mA depending on the signal polarity. See the Start-up Information section for system
timing waveforms associated with use of the ON/OFF pin.
Remote Sense (Pins 5 and 7)
The remote sense feature of the converter compensates for voltage drops occurring between the output pins of the converter
and the load. The SENSE(-) (Pin 5) and SENSE(+) (Pin 7) pins should be connected at the load or at the point where regulation
is required (see Fig. B).
866.513.2839
tech.support@psbel.com
© 2015 Bel Power Solutions, Inc.
BCD.00632_AA
QM48T40033
TM Series
Rw
QmaX
Vout (+)
100
Vin (+)
ON/OFF
Vin (-)
Converter
SENSE (+)
(Top View)
Rload
TRIM
Vin
SENSE (-)
10
Vout (-)
Rw
Fig. B: Remote sense circuit configuration.
If remote sensing is not required, the SENSE(-) pin must be connected to the Vout(-) pin (Pin 4), and the SENSE(+) pin must
be connected to the Vout(+) pin (Pin 8) to ensure the converter will regulate at the specified output voltage. If these
connections are not made, the converter will deliver an output voltage that is slightly higher than the specified value.
Because the sense leads carry minimal current, large traces on the end-user board are not required. However, sense traces
should be located close to a ground plane to minimize system noise and insure optimum performance. When wiring discretely,
twisted pair wires should be used to connect the sense lines to the load to reduce susceptibility to noise.
The converter’s output over-voltage protection (OVP) senses the voltage across Vout(+) and Vout(-), and not across the sense
lines, so the resistance (and resulting voltage drop) between the output pins of the converter and the load should be minimized
to prevent unwanted triggering of the OVP.
When utilizing the remote sense feature, care must be taken not to exceed the maximum allowable output power capability
of the converter, equal to the product of the nominal output voltage and the allowable output current for the given conditions.
When using remote sense, the output voltage at the converter can be increased by as much as 10% above the nominal rating
in order to maintain the required voltage across the load. Therefore, the designer must, if necessary, decrease the maximum
current (originally obtained from the derating curves) by the same percentage to ensure the converter’s actual output power
remains at or below the maximum allowable output power.
Output Voltage Adjust /TRIM (Pin 6)
The output voltage can be adjusted up 10% or down 20% relative to the rated output voltage by the addition of an externally
connected resistor. Trim up to 10% is guaranteed only at Vin ≥ 40 V, and it is marginal (8% to 10%) at Vin = 36 V.
The TRIM pin should be left open if trimming is not being used. To minimize noise pickup, a 0.1 µF capacitor is connected
internally between the TRIM and SENSE(-) pins.
To increase the output voltage, refer to Fig. C. A trim resistor, RT-INCR, should be connected between the TRIM (Pin 6) and
SENSE(+) (Pin 7), with a value of:
5.11(100 Δ)VONOM 626
RTINCR
10.22 [k]
1.225Δ
where,
RTINCR Required value of trim-up resistor k]
VONOM Nominal value of output voltage [V]
(VO-REQ VO-NOM)
Δ
X 100 [%]
VO-NOM
VOREQ Desired (trimmed) output voltage [V].
When trimming up, care must be taken not to exceed the converter‘s maximum allowable output power. See previous
section for a complete discussion of this requirement.
866.513.2839
tech.support@psbel.com
© 2015 Bel Power Solutions, Inc.
BCD.00632_AA
QM48T40033
QmaXTM Series
Converter
Vin (+)
ON/OFF
Vin (-)
Vout (+)
SENSE (+)
TRIM
(Top View)
R T-INCR
Rload
Vin
SENSE (-)
Vout (-)
Fig. C: Configuration for increasing output voltage.
To decrease the output voltage (Fig. D), a trim resistor, RT-DECR, should be connected between the TRIM (Pin 6) and
SENSE(-) (Pin 5), with a value of:
511
RTDECR
10.22 [k]
| Δ |
where,
RTDECR Required value of trim-down resistor [k]
and is as defined above.
Δ
Note: The above equations for calculation of trim resistor values match those typically used in conventional industry-standard
quarter bricks. For more information see Application Note 103.
TM Series
Converter
QmaX
Vin (+)
ON/OFF
Vin (-)
Vout (+)
SENSE (+)
TRIM
(Top View)
Rload
Vin
RT-DECR
SENSE (-)
Vout (-)
Fig. D: Configuration for decreasing output voltage.
Trimming/sensing beyond 110% of the rated output voltage is not an acceptable design practice, as this condition could
cause unwanted triggering of the output over-voltage protection (OVP) circuit. The designer should ensure that the difference
between the voltages across the converter’s output pins and its sense pins does not exceed 0.33 V, or:
[VOUT() VOUT()] [VSENSE() VSENSE()] 0.33 [V]
This equation is applicable for any condition of output sensing and/or output trim.
866.513.2839
tech.support@psbel.com
© 2015 Bel Power Solutions, Inc.
BCD.00632_AA
QM48T40033
Input Undervoltage Lockout
Input undervoltage lockout is standard with this converter. The converter will shut down when the input voltage drops
below a pre-determined voltage.
The input voltage must be at least 35 V for the converter to turn on. Once the converter has been turned on, it will shut off
when the input voltage drops below 31 V. This feature is beneficial in preventing deep discharging of batteries used in
telecom applications.
Output Overcurrent Protection (OCP)
The converter is protected against overcurrent or short circuit conditions. Upon sensing an overcurrent condition, the
converter will switch to constant current operation and thereby begin to reduce output voltage. When the output voltage
drops below 50% of the nominal value of output voltage, the converter will shut down.
Once the converter has shut down, it will attempt to restart nominally every 100 ms with a typical 1-2% duty cycle. The
attempted restart will continue indefinitely until the overload or short circuit conditions are removed or the output voltage
rises above 50% of its nominal value.
Output Overvoltage Protection (OVP)
The converter will shut down if the output voltage across Vout(+) (Pin 8) and Vout(-) (Pin 4) exceeds the threshold of the
OVP circuitry. The OVP circuitry contains its own reference, independent of the output voltage regulation loop. Once the
converter has shut down, it will attempt to restart every 100 ms until the OVP condition is removed.
Overtemperature Protection (OTP)
The converter will shut down under an overtemperature
condition to protect itself from overheating caused by
operation outside the thermal derating curves, or operation in abnormal conditions such as system fan failure. After the
converter has cooled to a safe operating temperature, it will automatically restart.
Safety Requirements
The converters meet North American and International safety regulatory requirements per UL60950 and EN60950 (pending).
Basic Insulation is provided between input and output.
To comply with safety agencies requirements, an input line fuse must be used external to the converter. A 7.5-A fuse is
recommended for use with this product.
Modules are UL approved for maximum fuse rating of 15-A. To protect a group of modules with a single fuse, the rating can
be increased from the recommended values above.
Electromagnetic Compatibility (EMC)
EMC requirements must be met at the end-product system level, as no specific standards dedicated to EMC
characteristics of board mounted component dc-dc converters exist. However, Bel Power Solutions tests its converters to
several system level standards, primary of which is the more stringent EN55022, Information technology equipment - Radio
disturbance characteristics - Limits and methods of measurement.
Effective internal LC differential filter significantly reduces input reflected ripple current, and improves EMC.
With the addition of a simple external filter, all versions of the QmaX™ Series of converters pass the requirements of Class
B conducted emissions per EN55022 and FCC, and meet at a minimum, Class A radiated emissions per EN 55022 and
Class B per FCC Title 47CFR, Part 15-J. Please contact Bel Power Solutions Applications Engineering for details of this
testing.
Fig. H: Location of the thermocouple for thermal testing.
866.513.2839
tech.support@psbel.com
© 2015 Bel Power Solutions, Inc.
BCD.00632_AA
QM48T40033
General Information
The converter has been characterized for many operational aspects, to include thermal derating (maximum load current as
a function of ambient temperature and airflow) for vertical and horizontal mounting, efficiency, start-up and shutdown
parameters, output ripple and noise, transient response to load step-change, overload and short circuit.
The following pages contain specific plots or waveforms associated with the converter. Additional comments for specific
data are provided below.
Test Conditions
All data presented were taken with the converter soldered to a test board, specifically a 0.060” thick printed wiring board
(PWB) with four layers. The top and bottom layers were not metalized. The two inner layers, comprising two-ounce
copper, were used to provide traces for connectivity to the converter.
The lack of metalization on the outer layers as well as the limited thermal connection ensured that heat transfer from the
converter to the PWB was minimized. This provides a worst-case but consistent scenario for thermal derating purposes.
All measurements requiring airflow were made in Bel Power Solutions’s vertical and horizontal wind tunnel facilities using
Infrared (IR) thermography and thermocouples for
thermometry.
Ensuring components on the converter do not exceed their ratings is important to maintaining high reliability. If one
anticipates operating the converter at or close to the maximum loads specified in the derating curves, it is prudent to check
actual operating temperatures in the application. Thermographic imaging is preferable; if this capability is not available, then
thermocouples may be used. Bel Power Solutions recommends the use of AWG #40 gauge thermocouples to ensure
measurement accuracy. Careful routing of the thermocouple leads will further minimize measurement error. Refer to Figure
H for optimum measuring thermocouple location.
Thermal Derating
Load current vs. ambient temperature and airflow rates are given in Figs. 1 and 2 for vertical and horizontal converter
mounting. Ambient temperature was varied between 25 °C and 85 °C, with airflow rates from 30 to 500 LFM (0.15 to 2.5
m/s).
For each set of conditions, the maximum load current was defined as the lowest of:
(i) The output current at which either any FET junction temperature did not exceed a maximum specified temperature
(120 °C) as indicated by the thermographic image, or
(ii) The nominal rating of the converter (40 A).
During normal operation, derating curves with maximum FET temperature less than or equal to 120 °C should not be
exceeded. Temperature on the PCB at the thermocouple location shown in Fig. H should not exceed 118 °C in order to
operate inside the derating curves.
Efficiency
Fig. 3 shows the efficiency vs. load current plot for ambient temperature of 25 ºC, airflow rate of 300 LFM (1.5 m/s) with
vertical mounting and input voltages of 36 V, 48 V and 72 V. Also, a plot of efficiency vs. load current, as a function of
ambient temperature with Vin = 48 V, airflow rate of 200 LFM (1 m/s) with vertical mounting is shown in Fig. 4.
Power Dissipation
Fig. 5 shows the power dissipation vs. load current plot for Ta = 25 ºC, airflow rate of 300 LFM (1.5 m/s) with vertical
mounting and input voltages of 36 V, 48 V and 72 V. Also, a plot of power dissipation vs. load current, as a function of
ambient temperature with Vin = 48 V, airflow rate of 200 LFM (1 m/s) with vertical mounting is shown in Fig. 6.
Start-up
Output voltage waveforms, during the turn-on transient using the ON/OFF pin for full rated load currents (resistive load) are
shown without and with external load capacitance in Fig. 7 and Fig. 8, respectively.
Ripple and Noise
Fig. 10 shows the output voltage ripple waveform, measured at full rated load current with a 10µF tantalum and 1µF
ceramic capacitor across the output. Note that all output voltage waveforms are measured across a 1F ceramic capacitor.
The input reflected ripple current waveforms are obtained using the test setup shown in Fig. 11. The corresponding
waveforms are shown in Fig. 12 and Fig. 13.
866.513.2839
tech.support@psbel.com
© 2015 Bel Power Solutions, Inc.
BCD.00632_AA
QM48T40033
Start-up Information (using negative ON/OFF)
VIN
Scenario #1: Initial Start-up From Bulk Supply
ON/OFF function enabled, converter started via
application of VIN. See Figure E.
Time
t0
Comments
ON/OFF pin is ON; system front end power
is toggled on, VIN to converter begins to
rise.
ON/OFF
STATE
OFF
ON
t1
VIN crosses Under-Voltage Lockout
protection circuit threshold; converter
enabled.
VOUT
t2
t3
Converter begins to respond to turn-on
command (converter turn-on delay).
Converter VOUT reaches 100% of nominal
value.
t
For this example, the total converter start-up time (t3-
t1) is typically 4 ms.
t0
t1 t2
t3
Fig. E: Start-up scenario #1.
VIN
Scenario #2: Initial Start-up Using ON/OFF Pin
With VIN previously powered, converter started via
ON/OFF pin. See Figure F.
Time
t0
t1
Comments
VINPUT at nominal value.
Arbitrary time when ON/OFF pin is enabled
(converter enabled).
ON/OFF
STATE
OFF
ON
t2
t3
End of converter turn-on delay.
Converter VOUT reaches 100% of nominal
value.
For this example, the total converter start-up time (t3-
t1) is typically 4 ms.
VOUT
t
t0
t1 t2
t3
Fig. F: Start-up scenario #2.
Scenario #3: Turn-off and Restart Using ON/OFF Pin
With VIN previously powered, converter is disabled and then
enabled via ON/OFF pin. See Figure G.
VIN
Time
t0
Comments
VIN and VOUT are at nominal values; ON/OFF pin ON.
ON/OFF pin arbitrarily disabled; converter output falls to
zero; turn-on inhibit delay period (100 ms typical) is
initiated, and ON/OFF pin action is internally inhibited.
ON/OFF pin is externally re-enabled.
t1
100 ms
ON/OFF
STATE
OFF
ON
t2
If (t2- t1) ≤ 100 ms, external action of ON/OFF pin is
locked out by start-up inhibit timer.
If (t2- t1) > 100 ms, ON/OFF pin action is internally
enabled.
VOUT
t3
Turn-on inhibit delay period ends. If ON/OFF pin is ON,
converter begins turn-on; if off, converter awaits ON/OFF
pin ON signal; see Figure F.
t4
t5
End of converter turn-on delay.
Converter VOUT reaches 100% of nominal value.
t
t0
t1
t2
t3 t4
t5
For the condition, (t2- t1) ≤ 100 ms, the total converter start-up time (t5-
t2) is typically 104 ms. For (t2- t1) > 100 ms, start-up will be typically 4
ms after release of ON/OFF pin.
Fig. G: Start-up scenario #3
866.513.2839
tech.support@psbel.com
© 2015 Bel Power Solutions, Inc.
BCD.00632_AA
QM48T40033
50
50
40
30
20
10
0
40
30
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
500 LFM (2.5 m/s)
400 LFM (2.0 m/s)
300 LFM (1.5 m/s)
200 LFM (1.0 m/s)
100 LFM (0.5 m/s)
30 LFM (0.15 m/s)
20
10
30 LFM (0.15 m/s)
0
20
30
40
50
60
70
80
90
20
30
40
50
60
70
80
90
Ambient Temperature [°C]
Ambient Temperature [°C]
Fig. 1: Available load current vs. ambient air temperature
and airflow rates for QM48T40033 converter with B height
pins mounted vertically with air flowing from pin 3 to pin 1,
MOSFET temperature 120C, Vin = 48 V.
Fig. 2: Available load current vs. ambient air temperature
and airflow rates for QM48T40033 converter with B height
pins mounted horizontally with air flowing from pin 3 to pin
1, MOSFET temperature 120C, Vin = 48 V.
0.95
0.90
0.85
0.80
0.95
0.90
0.85
0.80
72 V
48 V
36 V
70 C
55 C
40 C
0.75
0.75
0.70
0.65
0.70
0.65
0
10
20
30
40
50
0
10
20
30
40
50
Load Current [Adc]
Load Current [Adc]
Fig. 4: Efficiency vs. load current and ambient temperature
for converter mounted vertically with Vin = 48 V and air
flowing from pin 3 to pin 1 at a rate of 200 LFM (1.0 m/s).
Fig. 3: Efficiency vs. load current and input voltage for
converter mounted vertically with air flowing from pin 3 to
pin 1 at a rate of 300 LFM (1.5 m/s) and Ta = 25C.
16.00
12.00
8.00
16.00
12.00
8.00
72 V
48 V
36 V
70 C
55 C
40 C
4.00
4.00
0.00
0.00
0
10
20
30
40
50
0
10
20
30
40
50
Load Current [Adc]
Load Current [Adc]
Fig. 5: Power dissipation vs. load current and input voltage for
converter mounted vertically with air flowing from pin 3 to pin 1
at a rate of 300 LFM (1.5 m/s) and Ta = 25C.
Fig. 6: Power dissipation vs. load current and ambient
temperature for converter mounted vertically with Vin = 48 V and
air flowing from pin 3 to pin 1 at a rate of 200 LFM (1.0 m/s).
866.513.2839
tech.support@psbel.com
© 2015 Bel Power Solutions, Inc.
BCD.00632_AA
QM48T40033
Fig. 7: Turn-on transient at full rated load current (resistive)
with no output capacitor at Vin = 48 V, triggered via
ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom
trace: output voltage (1 V/div.) Time scale: 2 ms/div.
Fig. 8: Turn-on transient at full rated load current (resistive)
plus 40,000 F at Vin = 48 V, triggered via ON/OFF pin.
Top trace: ON/OFF signal (5 V/div.). Bottom trace: output
voltage (1 V/div.). Time scale: 2 ms/div.
Fig. 9: Output voltage response to load current step-
change (20 A – 30 A – 20 A) at Vin = 48 V. Top trace: output
voltage (100 mV/div.). Bottom trace: load current (10 A/div).
Current slew rate: 1 A/s. Co = 470 F tantalum + 1 F
ceramic. Time scale: 0.2 ms/div.
Fig. 10: Output voltage ripple (20 mV/div.) at full rated load
current into a resistive load with Co = 10 F tantalum + 1uF
ceramic and Vin = 48 V. Time scale: 1 s/div.
iS
iC
10 H
source
inductance
TM Series
33 F
ESR <1
electrolytic
capacitor
1 F
ceramic
capacitor
QmaX
DC/DC
Converter
Vout
Vsource
Fig. 11: Test setup for measuring input reflected ripple currents, ic and is.
866.513.2839
tech.support@psbel.com
© 2015 Bel Power Solutions, Inc.
BCD.00632_AA
QM48T40033
Fig. 12: Input reflected ripple current, is (10 mA/div),
measured through 10 H at the source at full rated load
current and Vin = 48 V. Refer to Fig. 11 for test setup. Time
scale: 1s/div.
Fig. 13: Input reflected ripple current, ic (100 mA/div),
measured at input terminals at full rated load current and
Vin = 48 V. Refer to Fig. 11 for test setup. Time scale: 1
s/div.
4.0
3.0
2.0
1.0
0
0
15
30
45
Iout [Adc]
Fig. 15: Load current (top trace, 20 A/div, 20 ms/div) into a
10 m short circuit during restart, at Vin = 48 V. Bottom
trace (20 A/div, 1 ms/div) is an expansion of the on-time
portion of the top trace.
Fig. 14: Output voltage vs. load current showing current
limit point and converter shutdown point. Input voltage has
almost no effect on current limit characteristic.
NOTE: The QM48T40033 is not recommended for new designs.
Product
Series
Input
Voltage
Mounting
Scheme
Rated Load
Current
Output
Voltage
ON/OFF
Logic
Maximum
Height (HT)
B
Pin
Length (PL)
Special
Features
QM
48
T
40
033
-
N
B
0
A 0.325”
B 0.358”
D 0.422”
A 0.188”
B 0.145”
C 0.110”
Quarter-
Brick
Format
Through-
hole
N Negative
P Positive
36-75 V
40 A
033 3.3 V
0 STD
The example above describes P/N QM48T40033-NBB0: 36-75 V input, through-hole mounting, 40 A @ 3.3 V output, negative ON/OFF logic, a
maximum height of 0.358”, and a through the board pin length of 0.145”. Please consult factory regarding availability of a specific version.
RoHS Ordering Information:
No RoHS suffix character is required for lead-solder-exemption compliance.
For RoHS compliance to all six substances, add the letter "G" as the last letter of the part number.
866.513.2839
tech.support@psbel.com
© 2015 Bel Power Solutions, Inc.
BCD.00632_AA
QM48T40033
PIN CONNECTIONS
Pin #
Function
Vin (+)
1
2
3
4
5
6
7
8
ON/OFF
Vin (-)
1
2
3
8
7
6
5
4
Vout (-)
SENSE(-)
TRIM
TOP VIEW
SIDE VIEW
SENSE(+)
Vout (+)
All dimensions are in inches [mm]
Pins 1-3 and 5-7 are Ø 0.040” [1.02]
with Ø 0.078” [1.98] shoulder
Pins 4 and 8 are Ø 0.062” [1.57]
without shoulder
Pin Material: Brass
Pin Finish: Tin/Lead over Nickel
Converter Weight: 1.06 oz [30 g]
typical
HT
CL
PL
Height
Option
Pin
Option
(Maximum Height)
+0.000 [+0.00]
-0.038 [-0.97]
(Minimum Clearance)
+0.016 [+0.41]
-0.000 [-0.00]
(Pin Length)
±0.005 [±0.13]
A
B
D
0.325 [8.26]
0.030 [0.77]
A
B
C
0.188 [4.77]
0.145 [3.68]
0.110 [2.79]
0.358 [9.09]
0.422 [10.72]
0.063 [1.60]
0.127 [3.23]
NUCLEAR AND MEDICAL APPLICATIONS - Products are not designed or intended for use as critical components in life support
systems, equipment used in hazardous environments, or nuclear control systems.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending
on the date manufactured. Specifications are subject to change without notice.
866.513.2839
tech.support@psbel.com
© 2015 Bel Power Solutions, Inc.
BCD.00632_AA
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明