CAT811STBIGT10 [CATALYST]
4-Pin Microprocessor Power Supply Supervisors with Manual Reset; 4引脚微处理器电源监控电路，带有手动复位
| 型号： | CAT811STBIGT10 |
| 厂家： | 
CATALYST SEMICONDUCTOR |
| 描述： | 4-Pin Microprocessor Power Supply Supervisors with Manual Reset |
| 文件： | 总9页 (文件大小：92K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
CAT811, CAT812
4-Pin Microprocessor Power Supply Supervisors with Manual Reset
FEATURES
DESCRIPTION
ꢀ Precision monitoring of
+5.0 V (± 5%, ± 10%, ± 20%),
+3.3 V (± 5%, ± 10%),
The CAT811 and CAT812 are microprocessor
supervisory circuits that monitor power supplies. The
CAT811 and CAT812 are direct replacements for the
MAX811andMAX812inapplicationsoperatingoverthe
industrial temperature range; both have a manual reset
input.
+3.0 V (± 10%) and
+2.5 V (± 5%) power supplies
ꢀ Manual reset input
Thesedevicesgeneratearesetsignal,whichisasserted
whilethepowersupplyvoltageisbelowapresetthreshold
level and for at least 140 ms after the power supply level
ꢀ Offered in two output configurations:
- CAT811: Active LOW reset
- CAT812: Active HIGH reset
has risen above that level. The underlying floating gate
ꢀ Direct replacements for the MAX811 and
MAX812 in applications operating over the
industrial temperature range
2(TM)
technology, AE
used by Catalyst Semiconductor,
makes it possible to offer any custom reset threshold
value. Seven industry standard threshold levels are
offered to support +5.0 V, +3.3 V, +3.0 V and +2.5 V
systems.
ꢀ Reset valid down to V = 1.0 V
CC
ꢀ 6 µA power supply current
ꢀ Power supply transient immunity
The CAT811 features a RESET push-pull output (active
LOW) and the CAT812 features a RESET push-pull
output (active HIGH).
ꢀ Available in SOT-143 packages with Sn or
NiPdAu Green Lead finishes.
ꢀ Industrial temperature range: -40°C to +85°C
Fast transients on the power supply are ignored and the
output is guaranteed to be in the correct state at V
levels as low as 1.0 V.
cc
APPLICATIONS
ꢀ Computers
The CAT811/812 are fully specified over the industrial
temperature range (-40°C to 85°C) and are available in
a compact 4-pin SOT143 package.
ꢀ Servers
ꢀ Laptops
ꢀ Cable modems
ꢀꢀ Wireless communications
ꢀ Embedded control systems
ꢀ White goods
ꢀ Power meters
ꢀ Intelligent instruments
ꢀ PDAs and handheld equipment
PIN CONFIGURATION
THRESHOLD SUFFIX SELECTOR
Nominal Threshold Threshold Suffix
Voltage
4.63V
4.38V
4.00V
3.08V
2.93V
2.63V
2.32V
Designation
GND
1
4
3
V
CC
L
M
J
CAT811
CAT812
T
S
R
Z
2
RESET
MR
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
Doc. No. 3005, Rev. R
1
CAT811, CAT812
ORDERING INFORMATION
Prefix
Device #
811
Suffix
GT10
CAT
S
TBI
Company ID
Trip Level
L: 4.63V
M: 4.38V
J: 4.00V
T: 3.08V
S: 2.93V
R: 2.63V
Z: 2.32V
Package Type
EUS: 4 pin SOT-143
TBI: 4 pin SOT-143 Green
Device Type
811: Push-Pull / Active Low Output
812: Push-Pull / Active High Output
Parts per Reel
T3: 3K units
T10: 10K units
GT3: 3K units (NiPdAu Lead Finish)*
GT10: 10K units (NiPdAu Lead Finish)*
The device shown in the examples (CAT811STBI-
GT10) has an Active Low, Push-Pull output; a trip level
of 2.85V to 3.00V and is provided in the Green SOT-23
package with a NiPdAu lead finish on tape and reel
with 10,000 units.
* NiPdAu is a Lead Finish Option on the Green
Packages only. Unless indicated with the “G” green
packages are shipped with a Sn Matte Lead Finish.
TOP MARKING
SOT-143
Green Sn
SOT-143
Green
Parts and
Threshold
Matte Lead
NiPdAu Lead
SOT-143 (1)
AMYM
ANYM
AZYM
APYM
AQYM
ARYM
AYYM
ASYM
ATYM
AUYM
AVYM
AWYM
AXYM
CIYM
Finish (1) (2)
Finish (1) (2)
CAT811L
CAT811M
CAT811J
CAT811T
CAT811S
CAT811R
CAT811Z
CAT812L
CAT812M
CAT812J
CAT812T
CAT812S
CAT812R
CAT812Z
DHYM
DJYM
CKYM
DLYM
DMYM
DNYM
CPYM
DRYM
DTYM
DUYM
DVYM
DWYM
DXYM
CYYM
ERYM
ESYM
Notes
1) The “YM” in the SOT-143 package marking indicates the Year
and Month of production.
2) All NiPdAu devices will be marked to indicate product type and
package. Threshold and full part numbers will be provided on box
and reel labels as well as all Shipping documents.
PIN DESCRIPTIONS
Pin Number
Name
Description
CAT811 CAT812
1
2
1
GND
Ground
—
RESET Active LOW reset. RESET is asserted if V
falls below the reset threshold
rises above the reset threshold.
CC
CC
and remains low for at least 140ms after V
—
3
2
3
RESET Active HIGH reset. RESET is asserted if V
falls below the reset
CC
threshold and remains high for at least 140ms after V
the reset threshold.
rises above
CC
MR
Manual Reset Input. A logic LOW on MR asserts RESET. RESET remains
active as long as MR is LOW and for 140ms after MR returns HIGH. The
active low input has an internal 20kΩ pull-up resistor. The input should be left
open if not used.
4
4
V
CC
Power supply voltage that is monitored.
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
Doc. No. 3005, Rev. R
2
CAT811, CAT812
Operating Temperature Range........... -40°C to +85°C
Storage Temperature Range ............ -65°C to +105°C
ABSOLUTE MAXIMUM RATINGS*
Any pin with respect to ground .......... -0.3 V to +6.0 V
Input Current, VCC ............................................. 20 mA
Output Current, RESET, RESET ...................... 20 mA
Rate of Rise, VCC ............................................................. 100 V/µs
Continuous Power Dissipation
Lead Soldering Temperature (10 sec).............. 300°C
*COMMENT
Stresses above those listed under “Absolute Maximum Ratings” may
cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions
outsideofthoselistedintheoperationalsectionsofthisspecificationisnot
implied. Exposure to any absolute maximum rating for extended periods
may affect device performance and reliability.
Derate 4mW/°C above 70°C (SOT143)........ 320 mW
ELECTRICAL CHARACTERISTICS
V
CC
= Full range, T = -40°C to +85°C unless otherwise noted. Typical values at T = +25°C and V = 5 V for the
A A CC
L/M/J versions, V = 3.3 V for the T/S versions, V = 3 V for the R version and V = 2.5 V for the Z version.
CC
CC
CC
Parameter
Symbol
Conditions
Min
1.0
1.2
Typ
Max
5.5
Units
VCC Range
TA = 0°C to +70°C
V
TA = -40°C to +85°C
5.5
VCC < 5.5 V, J/L/M
VCC < 3.6 V, R/S/T/Z
TA = +25°C
8
6
20
Supply Current
ICC
TA = -40˚C to +85˚C
µA
15
4.56
4.50
4.31
4.25
3.93
3.89
3.04
3.00
2.89
2.85
2.59
2.55
2.28
2.25
4.63
4.70
4.75
4.45
4.50
4.06
4.10
3.11
3.15
2.96
3.00
2.66
2.70
2.35
2.38
L Threshold
M Threshold
TA = -40°C to +85°C
TA = +25°C
4.38
4.00
3.08
2.93
2.63
2.32
TA = -40°C to +85°C
TA = +25°C
J Threshold
T Threshold
TA = -40°C to +85°C
TA = +25°C
Reset
Threshold
Voltage
V
TA = -40°C to +85°C
TA = +25°C
VTH
S Threshold
R Threshold
Z Threshold
TA = -40°C to +85°C
TA = +25°C
TA = -40°C to +85°C
TA = +25°C
TA = -40°C to +85°C
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
Doc No. 3005, Rev. R
3
CAT811, CAT812
(continued)
ELECTRICAL CHARACTERISTICS
V
CC
= Full range, T = -40˚C to +85˚C unless otherwise noted. Typical values at T = +25˚C and V = 5 V for
CC
A
A
L/M/J versions, V
= 3.3 V for T/S versions, V
= 3 V for R version and V
= 2.5 V for Z version.
CC
CC
CC
Parameter
Symbol
Conditions
Min
Typ(1) Max
Units
ppm/˚C
µs
Reset Threshold Tempco
VCC to Reset Delay (Note 2)
Reset Active Timeout Period
30
20
VCC = VTH to (VTH - 100 mV)
TA = -40˚C to +85˚C
140
240
400
0.3
ms
VCC = VTH min, ISINK = 1.2 mA
CAT811R/S/T/Z
RESET Output Voltage Low
(Push-pull, active LOW,
CAT811)
VOL
VCC = VTH min, ISINK = 3.2 mA
CAT811J/L/M
V
V
0.4
0.3
VCC > 1.0 V, ISINK = 50 µA
VCC = VTH max, ISOURCE = 500 µA
CAT811R/S/T/Z
0.8 VCC
RESET Output Voltage High
(Push-pull, active LOW,
CAT811)
VOH
VCC = VTH max, ISOURCE = 800 µA
CAT811J/L/M
VCC - 1.5
VCC > VTH max, ISINK = 1.2 mA
CAT812R/S/T/Z
0.3
0.4
RESET Output Voltage Low
(Push-pull, active HIGH,
CAT812)
V
V
VOL
VCC > VTH max, ISINK = 3.2 mA
CAT812J/L/M
RESET Output Voltage High
(Push-pull active HIGH,
CAT812)
VOH
1.8 V < VCC ≤ VTH min, ISOURCE = 150 µA
0.8 VCC
MR Minimum Pulse Width
tMR
10
µs
MR Glitch Immunity
Note 3
100
0.5
ns
MR to RESET Propagation
Delay
tMD
VIH
VIL
VIH
VIL
Note 2
µs
VCC > VTH (MAX), CAT811/812L/M/J
2.3 V
0.7VCC
10
0.8
MR Input Threshold
V
VCC > VIH (MAX), CAT811/812R/S/T/Z
0.25VCC
30
MR Pull-up Resistance
20
kΩ
Note 1: Production testing done at T = +25˚C; limits over temperature guaranteed by design only.
A
Note 2: RESET output for the CAT811; RESET output for the CAT812
Note 3: Glitches of 100 ns or less typically will not generate a reset pulse.
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
Doc. No. 3005, Rev. R
4
CAT811, CAT812
TYPICAL OPERATING CHARACTERISTICS
V
= Full range, T = -40˚C to +85˚C unless otherwise noted. Typical values at T = +25˚C and V = 5 V for
CC
CC
A
A
L/M/J versions, V =3.3 V for T/S versions, V
CC
= 3 V for R version and V
= 2.5 V for Z version.
CC
CC
POWER-UP RESET TIMEOUT
VS. TEMPERATURE
SUPPLY CURRENT VS. TEMPERATURE
(NO LOAD, CAT8xxR/S/T/Z)
260
12
10
8
V =5.5V
CC
240
220
200
180
160
V
=5V
CC
V =3.6V
CC
6
4
V =2.5V
CC
2
0
-50
0
50
100
150
-50
0
50
100
150
TEMPERATURE (˚C)
TEMPERATURE (˚C)
POWER-DOWN RESET DELAY VS. TEMPERATURE
(CAT8xxR/S/T/Z)
NORMALIZED RESET THRESHOLD
VS. TEMPERATURE
1.0002
1
14
12
10
8
0.9998
0.9996
0.9994
0.9992
0.999
0.9988
6
4
2
0
-50
0
50
100
150
0
20
40
60
80
100 120
TEMPERATURE (˚C)
TEMPERATURE (˚C)
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
Doc No. 3005, Rev. R
5
CAT811, CAT812
DETAILED DESCRIPTIONS
RESET TIMING
The reset signal is asserted LOW for the CAT811 and
HIGH for the CAT812 when the power supply voltage
fallsbelowthethresholdtripvoltageandremainsasserted
for at least 140ms after the power supply voltage has
risen above the threshold.
Threshold
Voltage
Power
Supply
Voltage
5V
0V
Reset Timeout Period
140ms
minimum
5V
0V
5V
0V
CAT811
CAT812
RESET
RESET
Figure 1. Reset Timing Diagram
V
CC
TRANSIENT RESPONSE
As the amplitude of the transient goes further below the
threshold (increasing V - V ), the maximum pulse
The CAT811/812 protect µPs against brownout failure.
Short duration transients of 4µsec or less and 100 mV
amplitude typically do not cause a false RESET.
TH
CC
duration decreases. In this test, the V starts from an
CC
initial voltage of 0.5V above the threshold and drops
Figure2showsthemaximumpulsedurationofnegative-
below it by the amplitude of the overdrive voltage (V
TH
goingV transientsthatdonotcausearesetcondition.
CC
- V ).
CC
30
25
20
15
10
T
= 25°C
AMB
CAT8xxZ
5
0
CAT8xxM
10
1
100
1000
RESET OVERDRIVE V - V [mV]
TH CC
Figure 2. Maximum Transient Duration Without Causing a Reset Pulse vs. Reset Comparator Overdrive
© 2005 by Catalyst Semiconductor, Inc.
Doc. No. 3005, Rev. R
6
Characteristics subject to change without notice
CAT811, CAT812
VALID RESET WITH V UNDER 1.0 V
CC
To ensure that the CAT811 RESET pin is in a known
state when V
is under 1.0 V, a 100 kΩ pull-down
CC
resistorbetweenRESETpinandGNDisrecommended;
the value is not critical. For the CAT812, a pull-up
resistor from RESET pin to V is needed.
CC
Power
Supply
Power
Supply
V
V
CC
CC
100kΩ
CAT812
CAT811
RESET
MR
MR
RESET
100kΩ
GND
GND
Figure 3. RESET Valid with V
Under 1.0 V
Figure 4. RESET Valid with V
Under 1.1 V
CC
CC
BI-DIRECTIONAL RESET PIN INTERFACING
TheCAT811/812caninterfacewithµP/µCbi-directional
reset pins by connecting a 4.7 kΩ resistor in series with
theCAT811/812resetoutputandtheµP/µCbi-directional
reset pin.
BUF
Buffered
RESET
Power
Supply
V
CC
CAT811
4.7kΩ
µP
RESET
GND
MR
RESET
INPUT
(For example: 68HC11)
GND
Bi-directional
I/O Pin
Figure 5. Bi-directional Reset Pin Interfacing
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
Doc No. 3005, Rev. R
7
CAT811, CAT812
OTHER SUPERVISORY PRODUCTS
Function
CAT1161/3
CAT1162
CAT809
CAT810
CAT811
CAT812
With 16k Bit Serial EEPROM Memory
Watchdog Timer
Manual Reset Input
Active Low Reset
Active High Reset
Dual Polarity Reset Outputs
Package
8-pin
DIP and SOIC
8-pin
DIP and SOIC
3-pin
SOT23 and
SC70
3-pin
SOT23 and
SC70
4-pin
SOT143
4-pin
SOT143
PACKAGE INFORMATION
Plastic SOT143 (4-Pin)
2.05 MAX
1.78 MIN
2.64 MAX
2.10 MIN
0.51 MAX
0.37 MIN
0.20
0.89 MAX
0.76 MIN
1.40 MAX
1.20 MIN
3.04 MAX
2.80 MIN
0.18 MAX
0.085 MIN
0.94 MAX
0.88 MIN
1.12 MAX
0.89 MIN
0.20
GAUGE PLANE
0.10 MAX
0.013 MIN
0.54 REF
0.41 MAX
0.21 MIN
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
Doc. No. 3005, Rev. R
8
REVISION HISTORY
Date
Rev.
L
Reason
10/22/03
12/22/2003
Updated Ordering Information
Updated Features
M
Replaced power-up reset timeout vs. temperature graph
with updated one
Replaced VCC Transient Response graph with updated
one
3/22/04
N
O
General data sheet updates
Updated Electrical Characteristics (Reset Active
Timeout Period Max)
3/25/2004
3/25/2004
9/28/2004
12/28/2005
P
Q
R
Corrected Pin Configure diagram
Minor changes
Updated Features
Updated Ordering Information
Updated Yop Marking
Copyrights, Trademarks and Patents
Trademarks and registered trademarks of Catalyst Semiconductor include each of the following:
2
DPP ™
AE ™
MiniPot™
Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products. For a complete list of patents
issued to Catalyst Semiconductor contact the Company’s corporate office at 408.542.1000.
CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS
PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE
RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING
OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES.
Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or
other applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a
situation where personal injury or death may occur.
Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets
labeled "Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale.
Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate
typical semiconductor applications and may not be complete.
Catalyst Semiconductor, Inc.
Corporate Headquarters
1250 Borregas Avenue
Sunnyvale, CA 94089
Publication #: 3005
Phone: 408.542.1000
Revison:
R
Fax: 408.542.1200
Issue date:
12/28/05
www.catalyst-semiconductor.com
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明