ESRD151M0EB [CDE]

Aluminum Electrolytic Capacitor, Polarized, Aluminum (solid Polymer), 2.5V, 20% +Tol, 20% -Tol, 150uF, Surface Mount, 2917, CHIP;


型号：	ESRD151M0EB
厂家：	CORNELL DUBILIER ELECTRONICS
描述：	Aluminum Electrolytic Capacitor, Polarized, Aluminum (solid Polymer), 2.5V, 20% +Tol, 20% -Tol, 150uF, Surface Mount, 2917, CHIP 电容器
文件：	总4页 (文件大小：319K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Type ESRD Solid Polymer Aluminum SMT Capacitors

Filtering power of 3 or more tantalum chips and 50 year life

Solid Polymer Aluminum capacitors combine the high capacitance capability of an

electrolytic component with the high frequency performance of ﬁlm capacitors.When

the need for low impedance at high frequency is critical for your design, one ESRD

chip is capable of replacing several liquid electrolyte aluminum or tantalum capacitors

connected in parallel. This is due to the ultra-low ESR which results in signiﬁcantly

lower impedance than either aluminum or tantalum capacitors at frequencies of 100

kHz and above. There is no longer a need to stack capacitors to lower the impedance

at high frequency. The low ESR and high capacitance make them ideal for bypassing

high frequency noise, and for switching frequency ﬁltering in DC/ DC conversion.

ESRD capacitors are packaged in a molded resin case with the same footprint (7.3 x

4.3 mm) as the industry standard tantalum“D”and“E”case sizes. The solid electrolyte

results in a capacitor with stable impedance and equivalent series resistance over

the entire operating temperature range and they have more than twice the ripple

current handling capability of tantalum capacitors. In addition, the solid electrolyte

RoHS Compliant

delivers a typical expected operating life of more than 50 years, and it is ignition free.

Applications

Motherboard By-Pass

Switching Supply Input/Output Filters

Power Supply Decoupling

High Frequency Noise Reduction

Laptop LCD Displays

Automotive Digital Equipment

Portable Electronic Equipment

Markings

Polarity Stripe (Anode)

Capacitance

(“R” = Decimal Point)

W.V. Code

D = 2.0 V K = 8.0 V

E = 2.5 V

G = 4.0 V C = 16.0 V

J = 6.3 V

B = 12.5 V

Lot Code

Ordering Information

ESRD

4R7

Packaging Code

R = Tape & Reel

ESRD (1.8 mm Ht.): 3500 pcs/reel

ESRD (2.8 mm Ht.): 2000 pcs/reel

CDE

Type

Capacitance

Code

Capacitance

Tolerance

M = ± 20%

4R7 = 4.7 µF

220 = 22 µF

101 = 100 µF

WVDC Code

02 = 2.0 Vdc 08 = 8.0 Vdc

0E = 2.5 Vdc 12 = 12.5 Vdc

04 = 4.0 Vdc 16 = 16.0 Vdc

06 = 6.3 Vdc

CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com

Type ESRD Solid Polymer Aluminum SMT Capacitors

High Voltage

Outline Drawing

Dimensions in mm

H = see ratings

table

Ratings

Maximum

E.S.R

100 kHz/20 °C

(Ω)

Maximum1

Case

Height

Catalog

Part Number

(Tape & Reel)

Ripple Current

100 kHz/105 °C

(Amps)

Capacitance

(µF)

(mm)

2.0 Vdc

0.018

100

120

180

220

270

ESRD101M02R

ESRD121M02XR

ESRD181M02R

ESRD221M02R

ESRD271M02XR

2.5

2.7

3.0

3.3

1.8 ±0.1

2.8 ±0.2

0.015

0.012

2.5 Vdc

0.018

ESRD820M0ER

ESRD101M0EXR

ESRD151M0ER

ESRD181M0ER

ESRD221M0EXR

2.5

2.7

3.0

3.3

1.8 ±0.1

2.8 ±0.2

100

150

180

220

0.015

0.012

4.0 Vdc

0.018

ESRD560M04R

ESRD820M04XR

ESRD121M04R

ESRD151M04XR

2.5

2.7

3.0

3.3

1.8 ±0.1

2.8 ±0.2

0.015

120

150

0.015

0.012

6.3 Vdc

0.055

ESRD100M06R

ESRD220M06R

ESRD330M06R

ESRD470M06R

ESRD680M06XR

ESRD101M06R

ESRD121M06XR

1.4

1.6

2.0

2.5

2.7

3.0

3.3

1.8 ±0.1

2.8 ±0.2

0.040

0.028

0.018

0.015

100

120

0.015

0.012

8.0 Vdc

0.055

8.2

ESRD8R2M08R

ESRD150M08R

ESRD220M08R

ESRD330M08R

ESRD680M08R

1.4

1.6

2.0

2.5

3.0

1.8 ±0.1

2.8 ±0.2

0.040

0.028

0.018

0.015

12.5 Vdc

0.080

4.7

ESRD4R7M12R

ESRD100M12R

ESRD150M12R

ESRD220M12R

1.0

1.3

1.6

1.8 ±0.1

0.060

0.050

0.030

16.0 Vdc

0.110

2.2

4.7

6.8

8.2

ESRD2R2M16R

ESRD4R7M16R

ESRD6R8M16R

ESRD8R2M16R

1.0

1.3

1.8 ±0.1

0.080

0.070

0.045

CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com

Type ESRD Solid Polymer Aluminum SMT Capacitors

Speciﬁcations

Operating Temperature Range:

Moisture Resistance:

–55 °C to +105 °C, at 100% rated voltage

After 500 hours storage at +60 ºC and 90% to

95% RH without load, the capacitor will meet the

following limits:

Surge Voltage:

125% of the rated working Vdc

ꢀꢀꢀꢀꢀ∆C = +70%/–20% of the initial

measured value (2.0 Vdc, 2.5 Vdc),

+60%/–20% of the initial

Capacitance Range:

2.2 µF to 270 µF

measured value (4.0 Vdc),

+50%/–20% of the initial

Capacitance Tolerance:

measured value (6.3 Vdc),

±20% at 120 Hz and +20 °C

+40%/–20% of the initial

measured value (all other voltages)

DF ≤ two times the initial speciﬁed value

DCL ≤ the initial speciﬁed value

DC Leakage Current (DCL):

After a two minute application of the rated working

voltage at +20 °C:

Life Test:

2V — 4V: I ≤0.06CV

6.3V — 16V: I ≤0.04CV or 3 µA

Apply rated DC working voltage at 105 ºC for 1000

hours, and then stabilize them to +20 ºC. Capacitors

will meet the following limits:

ꢀꢀꢀꢀꢀ

ꢀꢀꢀꢀꢀ∆C = ±10% of the initial measured value

DF ≤ the initial speciﬁed value

DCL ≤ the initial speciﬁed value

(whichever greater)

Dissipation Factor (DF):

The ratio of the capacitorís equivalent series

resistance to its reactance at 120Hz and +20 ºC

ESRD (1.8 mm ht.): DF is 0.06 Max.

ESRD (2.8 mm ht.): DF is 0.10 Max.

Shelf Life Test:

Shelf life is typically 5 to 10 years.Accelerated test:

after 500 hours at 105 ºC, capacitors will meet the

following limits after stabilization at 20 ºC:

ꢀꢀꢀꢀ

ꢀꢀꢀꢀꢀ∆C = ±10% of the initial measured value

DF ≤ꢀthe initial speciﬁed value

DCL ≤ the initial speciﬁed value

Resistance to Soldering Heat:

Heat the capacitors at 235 ºC in an oven for 200

seconds. The capacitors will meet the following

limits after stabilizing at 20 ºC:

ꢀ

∆C = ±10% of the initial measured value

DF ≤ the initial speciﬁed value

DCL ≤ the initial speciﬁed value

Shear Test:

No damage shall be visible after subjecting a

mounted capacitor to a side force of 5 N for 10

seconds

Vibration:

No abnormal change shall occur to capacitors that

have been soldered (and attached) to a board when

subjected to a vibration of 1.5 mm amplitude that

is varied from 10 Hz to 2000 Hz in 20 min. cycles.

The test duration is 2 hours for each right angle

direction (total 6 hours). Capacitance is monitored

during the last cycle of the test for stablilty.

(For more information on this product please see the Solid Polymer Aluminum Capacitors Application Guide)

CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com

Type ESRD Solid Polymer Aluminum SMT Capacitors

Notice and Disclaimer: All product drawings, descriptions, speciﬁcations, statements, information and data

(collectively, the “Information”) in this datasheet or other publication are subject to change. The customer

is responsible for checking, conﬁrming and verifying the extent to which the Information contained in this

datasheet or other publication is applicable to an order at the time the order is placed. All Information given

hereinisbelievedtobeaccurateandreliable,butitispresentedwithoutanyguarantee,warranty,representation

or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based

on the knowledge that the Cornell Dubilier company providing such statements (“Cornell Dubilier”) has

of operating conditions that such Cornell Dubilier company regards as typical for such applications, but

are not intended to constitute any guarantee, warranty or representation regarding any such matter – and

Cornell Dubilier speciﬁcally and expressly disclaims any guarantee, warranty or representation concerning

the suitability for a speciﬁc customer application, use, storage, transportation, or operating environment.

The Information is intended for use only by customers who have the requisite experience and capability to

determine the correct products for their application. Any technical advice inferred from this Information or

otherwise provided by Cornell Dubilier with reference to the use of any Cornell Dubilier products is given

gratis (unless otherwise speciﬁed by Cornell Dubilier), and Cornell Dubilier assumes no obligation or liability

for the advice given or results obtained. Although Cornell Dubilier strives to apply the most stringent quality

and safety standards regarding the design and manufacturing of its products, in light of the current state

of the art, isolated component failures may still occur. Accordingly, customer applications which require a

high degree of reliability or safety should employ suitable designs or other safeguards (such as installation

of protective circuitry or redundancies or other appropriate protective measures) in order to ensure that the

failure of an electrical component does not result in a risk of personal injury or property damage. Although

all product-related warnings, cautions and notes must be observed, the customer should not assume that all

safety measures are indicated in such warnings, cautions and notes, or that other safety measures may not be

required.

CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com

相关型号：