CG2164X3 [CEL]
Dual-Band Wireless DPDT RF Switch;
| 型号： | CG2164X3 |
| 厂家： | 
CALIFORNIA EASTERN LABS |
| 描述： | Dual-Band Wireless DPDT RF Switch 无线 光电二极管 |
| 文件： | 总8页 (文件大小：769K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
PRELIMINARY DATASHEET
RF SWITCH
Dual-Band Wireless DPDT RF Switch
DESCRIPTION
PACKAGE
The CG2164X3 is a GaAs MMIC DPDT (Double
Pole Double Throw) switch for 2.5 GHz and 6 GHz
dual-band wireless LAN applications
6-pin XSON Package
(1.5mm x 1.5mm x 0.37mm)
FEATURES
Control Voltage:
VC(H) = 1.8 to 5.0 V (3.0V TYP.)
VC(L) = -0.2 to 0.2 V (0V TYP.)
Low Insertion Loss:
Lins1 = 0.40 dB TYP. @ f = 2.4 to 2.5 GHz
Lins2 = 0.50 dB TYP. @ f = 4.9 to 6.0 GHz
High Isolation:
ISL1 = 23 dB TYP. @ f = 2.4 to 2.5 GHz
ISL2 = 15 dB TYP. @ f = 4.9 to 6.0 GHz
Power Handling:
Pin(0.5dB) = +32 dBm TYP. @ f = 2.5 GHz,
VC(H) = 3.0 V, VC(L) = 0 V
APPLICATIONS
Dual-band wireless LAN
(IEEE802.11a/b/g/n/ac)
Pin(0.5dB) = +30 dBm TYP. @ f = 6.0 GHz,
VC(H) = 3.0 V, VC(L) = 0 V
ORDERING INFORMATION
Part Number
CG2164X3
Order Number
CG2164X3-C2
Package
6-pin plastic
TSON
Marking
C0N
Description
• Embossed tape 8 mm wide
• Pin 1, 6 face the perforation side
of the tape
(Pb-Free)
• MOQ 10 kpcs/reel
CG2164X3-EVAL
CG2164X3-EVAL
• Evaluation Board with DC block
capacitors, power supply bypass
capacitors, and RF and DC
connectors
• MOQ 1
1
This document is subject to change without notice.
Date Published: December 2016
CDS-0033-02 (Issue B)
PRELIMINARY DATASHEET
CG2164X3
PIN CONFIGURATION AND
INTERNAL BLOCK DIAGRAM
Pin No.
Pin Name
ANT2
VC2
(Bottom View)
(Top View)
(Top View)
1
2
3
4
5
6
1
2
3
6
5
1
2
3
6
5
6
5
4
1
2
3
RX
TX
4
4
VC1
ANT1
Remark
Exposed pad : GND
TRUTH TABLE
VC1
High
Low
VC2
Low
High
ANT1-TX
OFF
ANT1-RX
ON
ANT2-TX
ON
ANT2-RX
OFF
ON
ON
OFF
OFF
ABSOLUTE MAXIMUM RATINGS
(TA = +25°C, unless otherwise specified)
Parameter
Symbol
Rating
Unit
V
6.0Note 1
+33.0Note 2
-45~+85
Control Voltage
VC
Pin
TA
Input Power
dBm
Operating Ambient Temperature
Storage Temperature
°C
°C
Tstg
-55~+150
Note 1. |VC1 - VC2| 6.0V
≦
2. 3.0V |VC1 – VC2| 5.0V
≦
≦
RECOMMENDED OPERATING RANGE
(TA = +25°C, unless otherwise specified)
Parameter
Symbol
MIN.
TYP.
MAX.
Unit
GHz
0.05
+1.8
-0.2
-
+3.0
0
6.0
Operating Frequency
f
Switch Control Voltage (H)
Switch Control Voltage (L)
VC(H)
+5.0
+0.2
V
V
VC(L)
2
This document is subject to change without notice.
PRELIMINARY DATASHEET
CG2164X3
ELECTRICAL CHARACTERISTICS
A
(T =+25°C, VC(H)=3.0V, VC(L)=0V, Zo=50Ω, DC Block Capacitance=8pF, unless otherwise specified)
Parameter
Symbol
Lins1
Test Conditions
MIN.
-
TYP.
0.40
MAX.
Unit
dB
Insertion Loss
f = 2.4 to 2.5 GHz
0.60
0.80
Lins2
ISL1
f = 4.9 to 6.0 GHz
f = 2.4 to 2.5 GHz
-
0.50
23
dB
dB
Isolation
20
-
-
-
-
(ANT to TX,RX)
ISL2
ISL3
ISL4
f = 4.9 to 6.0 GHz
f = 2.4 to 2.5 GHz
f = 4.9 to 6.0 GHz
12
22
15
15
25
18
dB
dB
dB
Isolation
(ANT1 to ANT2, TX to RX)
Return Loss
RL1
RL2
f = 2.4 to 2.5 GHz
f = 4.9 to 6.0 GHz
-
-
15
15
-
-
dB
dB
0.5 dB Loss Compression
Input Power Note
f = 2.4 to 2.5 GHz
-
-
-
-
-
-
+32
+30
85
-
-
-
-
-
-
dBm
dBm
dBc
dBc
dBc
dBc
Pin(0.5dB)
f = 4.9 to 6.0 GHz
2nd Harmonics
f = 2.5 GHz, Pin=+20dBm
f = 6.0 GHz, Pin=+20dBm
f = 2.5 GHz, Pin=+20dBm
f = 6.0 GHz, Pin=+20dBm
2f0
80
3rd Harmonics
85
3f0
85
3rd Order Input
Intercept Point
f = 2.5GHz
2-tone 1MHz Spacing
IIP3
-
+55
-
dBm
Switch Control Speed
Switch Control Current
tsw
50% CTL to 90/10%
Non RF
-
-
30
2
-
-
ns
Icont
μA
Note Pin(0.5dB) is the measured input power level when the insertion loss increases 0.5dB more than that of the linear
range.
3
This document is subject to change without notice.
PRELIMINARY DATASHEET
CG2164X3
EVALUATION CIRCUIT
8pF
8pF
ANT2
6
ANT1
1
VC2
RX
VC1
TX
2
3
5
4
1000 pF
1000 pF
8pF
8pF
The application circuits and their parameters are for reference only and are not intended for use in actual designs.
DC Blocking Capacitors are required at all RF ports.
PACKAGE DIMENSIONS
6-pin Plastic TSON (Unit: mm)
4
This document is subject to change without notice.
PRELIMINARY DATASHEET
CG2164X3
RECOMMENDED SOLDERING CONDITIONS
Recommended Soldering Conditions are available on CEL's Part Summary page under Associated Documents
5
This document is subject to change without notice.
PRELIMINARY DATASHEET
CG2164X3
REVISION HISTORY
Version
Change to current version
Preliminary datasheet
Page(s)
N/A
CDS-0033-01 (Issue A)
September 14, 2016
CDS-0033-02 (Issue B)
December 27, 2016
Revised Electrical Characteristics table
Added “Recommended Soldering Conditions” section
3, 5
6
This document is subject to change without notice.
PRELIMINARY DATASHEET
CG2164X3
[CAUTION]
・ All information included in this document is current as of the date this document is issued. Such information,
however, is subject to change without any prior notice.
・ You should not alter, modify, copy, or otherwise misappropriate any CEL product, whether in whole or in part.
・ CEL does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of
third parties by or arising from the use of CEL products or technical information described in this document. No
license, expressed, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual
property rights of CEL or others.
・ Descriptions of circuits, software and other related information in this document are provided only to illustrate the
operation of semiconductor products and application examples. You are fully responsible for the incorporation of
these circuits, software, and information in the design of your equipment. CEL assumes no responsibility for any
losses incurred by you or third parties arising from the use of these circuits, software, or information.
・ CEL has used reasonable care in preparing the information included in this document, but CEL does not warrant
that such information is error free. CEL assumes no liability whatsoever for any damages incurred by you resulting
from errors in or omissions from the information included herein.
・ Although CEL endeavors to improve the quality and reliability of its products, semiconductor products have specific
characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions.
Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or
damage caused by fire in the event of the failure of a CEL product, such as safety design for hardware and software
including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging
degradation or any other appropriate measures
Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final
products or system manufactured by you.
・ Please use CEL products in compliance with all applicable laws and regulations that regulate the inclusion or use of
controlled substances, including without limitation, the EU RoHS Directive.
CEL assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and
regulations.
・ This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent
of CEL.
・ Please contact CEL if you have any questions regarding the information contained in this document or CEL
products, or if you have any other inquiries.
7
This document is subject to change without notice.
PRELIMINARY DATASHEET
CG2164X3
[CAUTION]
This product uses gallium arsenide (GaAs) of the toxic substance appointed in laws and ordinances.
GaAs vapor and powder are hazardous to human health if inhaled or ingested.
・Do not dispose in fire or break up this product.
・Do not chemically make gas or powder with this product.
・When discarding this product, please obey the laws of your country.
・Do not lick the product or in any way allow it to enter the mouth.
[CAUTION]
Although this device is designed to be as robust as possible, ESD (Electrostatic Discharge) can
damage this device. This device must be protected at all times from ESD. Static charges may easily
produce potentials of several kilovolts on the human body or equipment, which can discharge
without detection. Industry-standard ESD precautions should be used at all times.
CEL Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054 • Tel: (408) 919-2500 • www.cel.com
For a complete list of sales offices, representatives and distributors,
Please visit our website: www.cel.com/contactus
For inquiries email us at rfw@cel.com
8
This document is subject to change without notice.
相关型号：
©2020 ICPDF网 联系我们和版权申明