PS9513L2-E3 [CEL]
1 Mbps, OPEN COLLECTOR OUTPUT, FOR GATE DRIVE INTERFACE INTELLIGENT POWER MODULE 8-PIN DIP PHOTOCOUPLER;
| 型号： | PS9513L2-E3 |
| 厂家： | 
CALIFORNIA EASTERN LABS |
| 描述： | 1 Mbps, OPEN COLLECTOR OUTPUT, FOR GATE DRIVE INTERFACE INTELLIGENT POWER MODULE 8-PIN DIP PHOTOCOUPLER 栅极驱动 输出元件 |
| 文件： | 总19页 (文件大小：1042K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
PHOTOCOUPLER
PS9513,PS9513L1,PS9513L2,PS9513L3
1 Mbps, OPEN COLLECTOR OUTPUT, FOR GATE DRIVE INTERFACE
INTELLIGENT POWER MODULE
8 mm CREEPAGE 8-PIN DIP HIGH-SPEED PHOTOCOUPLER
NEPOC Series
DESCRIPTION
The PS9513, PS9513L1, PS9513L2 and PS9513L3 are optically coupled isolators containing a GaAlAs LED on
the input side and a photo diode and a signal processing circuit on the output side on one chip.
The PS9513 is designed specifically for high common mode transient immunity (CMR) and low pulse width
distortion with operating temperature. It is suitable for IPM drive.
The PS9513L1 is lead bending type for long creepage distance.
The PS9513L2 is lead bending type for long creepage distance (Gull-wing) for surface mount.
The PS9513L3 is lead bending type (Gull-wing) for surface mounting.
FEATURES
•
•
•
•
•
•
•
Long creepage distance (8 mm MIN. : PS9513L1, PS9513L2)
High common mode transient immunity (CMH, CML = 15 kV/ s MIN.)
High-speed response (tPHL = 500 ns MAX., tPLH = 750 ns MAX.)
Maximum propagation delays (tPLH tPHL = 270 ns TYP.)
Pulse width distortion ( | tPHL tPLH | = 270 ns TYP.)
Open collector output
Ordering number of tape product : PS9513L2-E3 : 1 000 pcs/reel
: PS9513L3-E3 : 1 000 pcs/reel
•
•
Pb-Free product
Safety standards
•
•
•
•
•
•
•
•
UL approved: No. E72422
CSA approved: No. CA 101391 (CA5A, CAN/CSA-C22.2 60065, 60950)
BSI approved: No. 8937, 8938
<R>
<R>
SEMKO approved: No. 615433
NEMKO approved: No. P06207243
DEMKO approved: No. 314091
FIMKO approved: No. FI 22827
DIN EN60747-5-2 (VDE0884 Part2) approved: No. 40019182 (Option)
APPLICATIONS
•
•
IPM Driver
General purpose inverter
Document No. PN10679EJ03V0DS (3rd edition)
Date Published September 2009 NS
The mark <R> shows major revised points.
The revised points can be easily searched by copying an "<R>" in the PDF file and specifying it in the "Find what:" field.
PS9513,PS9513L1,PS9513L2 PS9513L3
PACKAGE DIMENSIONS (UNIT: mm)
DIP Type
<R>
Lead Bending Type (Gull-wing) For Surface Mount
2
Data Sheet PN10679EJ03V0DS
PS9513,PS9513L1,PS9513L2 PS9513L3
Lead Bending Type For Long Creepage Distance
Lead Bending Type For Long Creepage Distance (Gull-wing) For Surface Mount
3
Data Sheet PN10679EJ03V0DS
PS9513,PS9513L1,PS9513L2 PS9513L3
PHOTOCOUPLER CONSTRUCTION
Parameter
Air Distance (MIN.)
PS9513, PS9513L3
PS9513L1, PS9513L2
7 mm
7 mm
8 mm
8 mm
Outer Creepage Distance (MIN.)
Isolation Distance (MIN.)
0.4 mm
0.4 mm
FUNCTIONAL DIAGRAM
MARKING EXAMPLE
<R>
4
Data Sheet PN10679EJ03V0DS
PS9513,PS9513L1,PS9513L2 PS9513L3
ORDERING INFORMATION
Part Number
Order Number
Solder Plating
Specification
Packing Style
Safety Standard
Approval
Application Part
Number*1
PS9513
PS9513-AX
Pb-Free
Magazine case 50 pcs
Standard products
(UL, CSA, BSI,
PS9513
PS9513L1
PS9513L1-AX
(Ni/Pd/Au)
PS9513L1
PS9513L2
PS9513L3
PS9513L2
PS9513L3
PS9513
PS9513L2
PS9513L2-AX
SEMKO, NEMKO,
DEMKO, FIMKO
PS9513L3
PS9513L3-AX
PS9513L2-E3
PS9513L3-E3
PS9513-V
PS9513L2-E3-AX
PS9513L3-E3-AX
PS9513-V-AX
Embossed Tape 1 000 pcs/reel approved)
Magazine case 50 pcs
DIN EN60747-5-2
PS9513L1-V
PS9513L2-V
PS9513L3-V
PS9513L2-V-E3
PS9513L3-V-E3
PS9513L1-V-AX
PS9513L2-V-AX
PS9513L3-V-AX
PS9513L2-V-E3-AX
PS9513L3-V-E3-AX
(VDE0884 Part2)
Approved (Option)
PS9513L1
PS9513L2
PS9513L3
PS9513L2
PS9513L3
Embossed Tape 1 000 pcs/reel
*1 For the application of the Safety Standard, following part number should be used.
5
Data Sheet PN10679EJ03V0DS
PS9513,PS9513L1,PS9513L2 PS9513L3
ABSOLUTE MAXIMUM RATINGS (TA = 25 C, unless otherwise specified)
Parameter
Symbol
IF
Ratings
25
Unit
mA
V
Diode
Forward Current *1
Reverse Voltage
VR
5.0
Detecto Supply Voltage
r
VCC
0.5 to +35
V
Output Voltage
Output Current
VO
IO
0.5 to +35
15
V
mA
mW
Vr.m.s.
C
Power Dissipation*2
PC
BV
TA
100
Isolation Voltage *3
5 000
Operating Ambient Temperature
Storage Temperature
40 to +100
55 to +125
Tstg
C
*1 Reduced to 0.33 mA/ C at TA = 70 C or more.
*2 Reduced to 2.0 mW/ C at TA = 70 C or more.
*3 AC voltage for 1 minute at TA = 25 C, RH = 60% between input and output.
Pins 1-4 shorted together, 5-8 shorted together.
RECOMMENDED OPERATING CONDITIONS
Parameter
Forward Current
Symbol
IF
MIN.
10
0
TYP.
15
MAX.
20
Unit
mA
V
Output Voltage
Supply Voltage
Input Voltage
VO
30
VCC
VF
4.5
0
30
V
0.8
V
6
Data Sheet PN10679EJ03V0DS
PS9513,PS9513L1,PS9513L2 PS9513L3
ELECTRICAL CHARACTERISTICS (TA = 40 to +100 C, VCC = 15 V, unless otherwise specified)
Parameter
Symbol
VF
Conditions
MIN.
1.3
TYP.*1
1.65
MAX.
2.1
Unit
V
Diode
Forward Voltage
Reverse Current
Terminal Capacitance
IF = 10 mA
VR = 3 V
IR
200
A
Ct
V = 0 V, f = 1 MHz, TA = 25 C
IF = 10 mA, IOL = 2.4 mA
30
0.13
1.0
pF
V
Detector Low Level Output Voltage
High Level Output Current
VOL
IOH
0.6
50
VCC = 30 V, VF = 0.8 V
A
High Level Supply Current
ICCH
ICCL
IFHL
VCC = 30 V, VF = 0.8 V, VO = open
VCC = 30 V, IF = 10 mA, VO = open
VO = 0.8 V, IO = 0.75 mA
0.6
1.3
1.3
5.0
mA
mA
mA
Low Level Supply Current
0.6
Coupled Threshold Input Current
0.86
(H
L)
Current Transfer Ratio (IC/IF)
Isolation Resistance
CTR
IF = 10 mA, VO = 0.6 V
44
110
%
RI-O
VI-O = 1 kVDC, RH = 40 to 60%,
TA = 25 C
1011
Isolation Capacitance
CI-O
tPHL
V = 0 V, f = 1 MHz, TA = 25 C
0.7
pF
ns
Propagation Delay Time
IF = 10 mA, RL = 20 k , CL = 100 pF,
VTHHL = 1.5 V, VTHLH = 2.0 V
250
500
750
650
650
(H
L)*2
Propagation Delay Time
(L
H)*2
tPLH
520
270
270
Maximum Propagation
Delays
tPLH tPHL
200
Pulse Width Distortion
(PWD)*2
|tPHL tPLH
|
Common Mode
CMH
TA = 25 C, IF = 0 mA, VO > 3.0 V,
VCM = 1.5 kV, RL = 20 k ,
CL = 100 pF
15
15
kV/ s
kV/ s
Transient Immunity at High
Level Output*3
Common Mode
CML
TA = 25 C, IF = 10 mA, VO < 1.0 V,
VCM = 1.5 kV, RL = 20 k ,
CL = 100 pF
Transient Immunity at Low
Level Output*3
7
Data Sheet PN10679EJ03V0DS
PS9513,PS9513L1,PS9513L2 PS9513L3
*1 Typical values at TA = 25 C.
*2 Test circuit for propagation delay time
*3 Test circuit for common mode transient immunity
USAGE CAUTIONS
1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static
electricity when handling.
2. By-pass capacitor of more than 0.1 F is used between VCC and GND near device. Also, ensure that the
distance between the leads of the photocoupler and capacitor is no more than 10 mm.
3. Pins 1, 4 (which is an NC*1 pin) can either be connected directly to the GND pin on the LED side or left open.
Also, Pin 7 (which is an NC*1 pin) can either be connected directly to the GND pin on the detector side or left
open.
<R>
Unconnected pins should not be used as a bypass for signals or for any other similar purpose because this
may degrade the internal noise environment of the device.
*1 NC: Non-Connection (No Connection)
4. Avoid storage at a high temperature and high humidity.
8
Data Sheet PN10679EJ03V0DS
PS9513,PS9513L1,PS9513L2 PS9513L3
TYPICAL CHARACTERISTICS (TA = 25 C, unless otherwise specified)
Remark The graphs indicate nominal characteristics.
9
Data Sheet PN10679EJ03V0DS
PS9513,PS9513L1,PS9513L2 PS9513L3
Remark The graphs indicate nominal characteristics.
10
Data Sheet PN10679EJ03V0DS
PS9513,PS9513L1,PS9513L2 PS9513L3
Remark The graphs indicate nominal characteristics.
11
Data Sheet PN10679EJ03V0DS
PS9513,PS9513L1,PS9513L2 PS9513L3
TAPING SPECIFICATIONS (UNIT: mm)
12
Data Sheet PN10679EJ03V0DS
PS9513,PS9513L1,PS9513L2 PS9513L3
13
Data Sheet PN10679EJ03V0DS
PS9513,PS9513L1,PS9513L2 PS9513L3
RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm)
14
Data Sheet PN10679EJ03V0DS
PS9513,PS9513L1,PS9513L2 PS9513L3
NOTES ON HANDLING
1. Recommended soldering conditions
(1) Infrared reflow soldering
• Peak reflow temperature
260 C or below (package surface temperature)
10 seconds or less
• Time of peak reflow temperature
• Time of temperature higher than 220 C
60 seconds or less
• Time to preheat temperature from 120 to 180 C 120 30 s
• Number of reflows
• Flux
Three
Rosin flux containing small amount of chlorine (The flux with a
maximum chlorine content of 0.2 Wt% is recommended.)
(2) Wave soldering
• Temperature
• Time
260 C or below (molten solder temperature)
10 seconds or less
• Preheating conditions
• Number of times
• Flux
120 C or below (package surface temperature)
One (Allowed to be dipped in solder including plastic mold portion.)
Rosin flux containing small amount of chlorine (The flux with a maximum chlorine
content of 0.2 Wt% is recommended.)
(3) Soldering by soldering iron
• Peak temperature (lead part temperature) 350 C or below
• Time (each pins)
• Flux
3 seconds or less
Rosin flux containing small amount of chlorine (The flux with a
maximum chlorine content of 0.2 Wt% is recommended.)
(a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead.
(b) Please be sure that the temperature of the package would not be heated over 100 C.
15
Data Sheet PN10679EJ03V0DS
PS9513,PS9513L1,PS9513L2 PS9513L3
(4) Cautions
• Fluxes
Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent.
2. Cautions regarding noise
Be aware that when voltage is applied suddenly between the photocoupler’s input and output or between VCC-
GND at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum
ratings.
16
Data Sheet PN10679EJ03V0DS
PS9513,PS9513L1,PS9513L2 PS9513L3
<R>
SPECIFICATION OF VDE MARKS LICENSE DOCUMENT
Parameter
Symbol
Speck
Unit
Climatic test class (IEC 60068-1/DIN EN 60068-1)
40/100/21
Dielectric strength
maximum operating isolation voltage
Test voltage (partial discharge test, procedure a for type test and random test)
Upr = 1.5 UIORM, Pd 5 pC
UIORM
Upr
1 130
1 695
Vpeak
Vpeak
Test voltage (partial discharge test, procedure b for all devices)
Upr = 1.875 UIORM, Pd 5 pC
Upr
2 119
Vpeak
Vpeak
Highest permissible overvoltage
UTR
8 000
2
Degree of pollution (DIN EN 60664-1 VDE0110 Part 1)
Comparative tracking index (IEC 60112/DIN EN 60112 (VDE 0303 Part 11))
Material group (DIN EN 60664-1 VDE0110 Part 1)
Storage temperature range
CTI
175
III a
Tstg
TA
–55 to +125
–40 to +100
°C
°C
Operating temperature range
Isolation resistance, minimum value
VIO = 500 V dc at TA = 25°C
Ris MIN.
Ris MIN.
1012
1011
VIO = 500 V dc at TA MAX. at least 100°C
Safety maximum ratings (maximum permissible in case of fault, see thermal
derating curve)
Package temperature
Tsi
Isi
175
400
700
°C
mA
mW
Current (input current IF, Psi = 0)
Power (output or total power dissipation)
Isolation resistance
Psi
VIO = 500 V dc at TA = Tsi
Ris MIN.
109
17
Data Sheet PN10679EJ03V0DS
PS9513,PS9513L1,PS9513L2 PS9513L3
18
Data Sheet PN10679EJ03V0DS
PS9513,PS9513L1,PS9513L2 PS9513L3
This product uses gallium arsenide (GaAs).
Caution GaAs Products
GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the
following points.
• Follow related laws and ordinances when disposing of the product. If there are no applicable laws
and/or ordinances, dispose of the product as recommended below.
1. Commission a disposal company able to (with a license to) collect, transport and dispose of
materials that contain arsenic and other such industrial waste materials.
2. Exclude the product from general industrial waste and household garbage, and ensure that the
product is controlled (as industrial waste subject to special control) up until final disposal.
• Do not burn, destroy, cut, crush, or chemically dissolve the product.
• Do not lick the product or in any way allow it to enter the mouth.
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明