UPG2415TK [CEL]
0.5 to 6.0 GHz SPDT SWITCH; 0.5至6.0千兆赫的SPDT开关型号: | UPG2415TK |
厂家: | CALIFORNIA EASTERN LABS |
描述: | 0.5 to 6.0 GHz SPDT SWITCH |
文件: | 总11页 (文件大小:541K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
GaAs INTEGRATED CIRCUIT
PG2415TK
0.5 to 6.0 GHz SPDT SWITCH
DESCRIPTION
The PG2415TK is a GaAs MMIC SPDT (Single Pole Double Throw) switch for 0.5 to 6.0 GHz applications,
including dual-band wireless LAN.
This device operates with dual control switching voltages of 2.7 to 5.3 V. This device can operate at frequencies
from 0.5 to 6.0 GHz, with low insertion loss and high isolation.
This device is housed in a 6-pin lead-less minimold package (1511 PKG) and is suitable for high-density surface
mounting.
FEATURES
• Switch control voltage
• Low insertion loss
• High isolation
: Vcont (H) = 3.0 V TYP.
: Vcont (L) = 0 V TYP.
: Lins = 0.45 dB TYP. @ f = 2.5 GHz
: Lins = 0.65 dB TYP. @ f = 6.0 GHz
: ISL = 28 dB TYP. @ f = 2.5 GHz
: ISL = 26 dB TYP. @ f = 6.0 GHz
: Pin (0.1 dB) = +31.0 dBm TYP. @ f = 2.0 to 6.0 GHz
• Handling power
• High-density surface mounting : 6-pin lead-less minimold package (1.5 1.1 0.55 mm)
APPLICATIONS
• Dual-band wireless LAN etc.
ORDERING INFORMATION
Part Number
Order Number
Package
Marking
G6D
Supplying Form
PG2415TK-E2 PG2415TK-E2-A
6-pin lead-less minimold
(1511 PKG) (Pb-Free)
Embossed tape 8 mm wide
Pin 1, 6 face the perforation side of the tape
Qty 5 kpcs/reel
Remark To order evaluation samples, please contact your nearby sales office.
Part number for sample order: PG2415TK-A
Caution Although this device is designed to be as robust as possible, ESD (Electrostatic
Discharge) can damage this device. This device must be protected at all times from ESD. Static
charges may easily produce potentials of several kilovolts on the human body or equipment, which
can discharge without detection. Industry-standard ESD precautions must be employed at all times.
Document No. PG10793EJ01V0DS (1st edition)
Date Published February 2010 NS
PG2415TK
PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM
Pin No.
Pin Name
RF1
1
2
3
4
5
6
GND
RF2
Vcont2
RFC
Vcont1
SW TRUTH TABLE
ON Path
RFC-RF1
RFC-RF2
Vcont1
High
Low
Vcont2
Low
High
ABSOLUTE MAXIMUM RATINGS (TA = +25C, unless otherwise specified)
Parameter
Switch Control Voltage
Symbol
Vcont
Pin
Ratings
Unit
V
Note
+6.0
Input Power (Vcont (H) = 3.0 V)
Input Power (Vcont (H) = 5.0 V)
Power Dissipation (average)
Operating Ambient Temperature
Storage Temperature
+34.0
+35.0
dBm
dBm
W
Pin
PD
0.15
TA
45 to +85
55 to +150
C
Tstg
C
Note Vcont1 Vcont2 6.0 V
RECOMMENDED OPERATING RANGE (TA = +25C, unless otherwise specified)
Parameter
Operating Frequency
Symbol
f
MIN.
0.5
TYP.
MAX.
6.0
Unit
GHz
V
Switch Control Voltage (H)
Switch Control Voltage (L)
Control Voltage Difference
Vcont (H)
Vcont (L)
Vcont (H),
2.7
3.0
0
5.3
0.2
0.1
0.2
V
0
0.1
V
Note
Vcont (L)
Note Vcont (H) = Vcont1 (H) Vcont2 (H)
Vcont (L) = Vcont1 (L) Vcont2 (L)
2
Data Sheet PG10793EJ01V0DS
PG2415TK
ELECTRICAL CHARACTERISTICS
(TA = +25C, Vcont (H) = 3.0 V, Vcont (L) = 0 V, ZO = 50 , DC blocking capacitors = 8 pF, unless
otherwise specified)
Parameter
Insertion Loss 1
Symbol
Lins1
Lins2
Lins3
Lins4
ISL1
ISL2
ISL3
ISL4
RL1
Test Conditions
f = 0.5 to 2.0 GHz Note 1
MIN.
TYP.
0.40
0.45
0.55
0.65
28
MAX.
Unit
dB
0.65
0.70
0.80
0.90
Insertion Loss 2
Insertion Loss 3
Insertion Loss 4
Isolation 1
f = 2.0 to 2.5 GHz
f = 2.5 to 3.8 GHz
f = 3.8 to 6.0 GHz
f = 0.5 to 2.0 GHz Note 1
f = 2.0 to 2.5 GHz
f = 2.5 to 3.8 GHz
f = 3.8 to 6.0 GHz
f = 0.5 to 2.0 GHz Note 1
f = 2.0 to 2.5 GHz
f = 2.5 to 6.0 GHz
dB
dB
dB
25
25
25
22
15
15
10
dB
Isolation 2
28
dB
Isolation 3
28
dB
Isolation 4
26
dB
Return Loss 1
Return Loss 2
Return Loss 3
0.1 dB Loss Compression
Input Power Note 2
20
dB
RL2
20
dB
RL3
15
dB
Pin (0.1 dB) f = 0.5 to 2.0 GHz Note 1
+32.0
+31.0
+35.0
+34.0
+34.0
+60
80
dBm
dBm
dBm
dBm
dBm
dBm
dBc
dBc
A
f = 2.0 to 6.0 GHz
f = 0.5 to 6.0 GHz Note 1, Vcont (H) = 5.0 V
f = 0.5 to 2.0 GHz Note 1
1 dB Loss Compression
Input Power Note 3
Pin (1 dB)
f = 2.0 to 6.0 GHz
Input 3rd Order Intercept Point
2nd Harmonics
IIP3
2f0
f = 2.5 GHz, Pin = +20 dBm
f = 2.5 GHz, Pin = +20 dBm
f = 2.5 GHz, Pin = +20 dBm
No RF input
3rd Harmonics
3f0
80
Switch Control Current
Switch Control Speed
Icont
tSW
0.1
10
250
50% CTL to 90/10% RF
50
ns
Notes 1. DC blocking capacitors = 56 pF at f = 0.5 to 2.0 GHz
2. Pin (0.1 dB) is the measured input power level when the insertion loss increases 0.1 dB more than that of
the linear range.
3. Pin (1 dB) is the measured input power level when the insertion loss increases 1 dB more than that of the
linear range.
Caution It is necessary to use DC blocking capacitors with this device.
The value of DC blocking capacitors should be chosen to accommodate the frequency of
operation, bandwidth, switching speed and the condition with actual board of your system.
3
Data Sheet PG10793EJ01V0DS
PG2415TK
EVALUATION CIRCUIT
Note C1 : 0.5 to 2.0 GHz
: 2.0 to 6.0 GHz
56 pF
8 pF
C2 : 1 000 pF
The application circuits and their parameters are for reference only and are not intended for use in actual design-ins
APPLICATION INFORMATION
• LESD provides a means to increase the ESD protection on a specific RF port, typically the port attached to the
antenna.
• The value may be tailored to provide specific electrical responses.
• The RF ground connections should be kept as short as possible and connected to directly to a good RF ground
for best performance.
4
Data Sheet PG10793EJ01V0DS
PG2415TK
ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD
USING THE EVALUATION BOARD
Symbol
Test Conditions
f = 0.5 to 2.0 GHz
f = 2.0 to 6.0 GHz
Values
56 pF
C1
C2
8 pF
1 000 pF
5
Data Sheet PG10793EJ01V0DS
PG2415TK
TYPICAL CHARACTERISTICS (TA = +25C, Vcont (H) = 3.0 V, Vcont (L) = 0 V, ZO = 50 , DC blocking
capacitors = 8 pF, unless otherwise specified)
Remark The graphs indicate nominal characteristics.
6
Data Sheet PG10793EJ01V0DS
PG2415TK
Remark The graphs indicate nominal characteristics.
7
Data Sheet PG10793EJ01V0DS
PG2415TK
MOUNTING PAD LAYOUT DIMENSIONS
6-PIN LEAD-LESS MINIMOLD (1511 PKG) (UNIT: mm)
Remark The mounting pad layout in this document is for reference only.
8
Data Sheet PG10793EJ01V0DS
PG2415TK
PACKAGE DIMENSIONS
6-PIN LEAD-LESS MINIMOLD (1511 PKG) (UNIT: mm)
9
Data Sheet PG10793EJ01V0DS
PG2415TK
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered and mounted under the following recommended conditions. For soldering
methods and conditions other than those recommended below, contact your nearby sales office.
Soldering Method
Infrared Reflow
Soldering Conditions
Condition Symbol
IR260
Peak temperature (package surface temperature)
Time at peak temperature
: 260C or below
: 10 seconds or less
: 60 seconds or less
: 12030 seconds
: 3 times
Time at temperature of 220C or higher
Preheating time at 120 to 180C
Maximum number of reflow processes
Maximum chlorine content of rosin flux (% mass)
: 0.2%(Wt.) or below
Wave Soldering
Partial Heating
Peak temperature (molten solder temperature)
Time at peak temperature
: 260C or below
: 10 seconds or less
: 120C or below
: 1 time
WS260
HS350
Preheating temperature (package surface temperature)
Maximum number of flow processes
Maximum chlorine content of rosin flux (% mass)
: 0.2%(Wt.) or below
Peak temperature (terminal temperature)
Soldering time (per side of device)
: 350C or below
: 3 seconds or less
: 0.2%(Wt.) or below
Maximum chlorine content of rosin flux (% mass)
Caution Do not use different soldering methods together (except for partial heating).
10
Data Sheet PG10793EJ01V0DS
PG2415TK
This product uses gallium arsenide (GaAs).
Caution GaAs Products
GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the
following points.
• Follow related laws and ordinances when disposing of the product. If there are no applicable laws
and/or ordinances, dispose of the product as recommended below.
1. Commission a disposal company able to (with a license to) collect, transport and dispose of
materials that contain arsenic and other such industrial waste materials.
2. Exclude the product from general industrial waste and household garbage, and ensure that the
product is controlled (as industrial waste subject to special control) up until final disposal.
• Do not burn, destroy, cut, crush, or chemically dissolve the product.
• Do not lick the product or in any way allow it to enter the mouth.
Data Sheet PG10793EJ01V0DS
11
相关型号:
©2020 ICPDF网 联系我们和版权申明