CHC1084-ADJPAGP [CHENMKO]

Regulator,;
CHC1084-ADJPAGP
型号: CHC1084-ADJPAGP
厂家: CHENMKO ENTERPRISE CO. LTD.    CHENMKO ENTERPRISE CO. LTD.
描述:

Regulator,

文件: 总6页 (文件大小:267K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
CHENMKO ENTERPRISE CO.,LTD  
CHC1084PAGP SERIES  
Low Dropout Linear Regulator  
„ GENERAL DESCRIPTION  
„ FEATURES  
The CHC1084PA is a series of low dropout three-terminal  
z
z
z
z
z
z
1.5V maximum dropout at full load current  
Fast transient response  
regulators with a dropout of 1.5V at 1A output current.  
The CHC1084PA series provides current limiting and  
thermal shutdown. Its circuit includes a trimmed  
bandgap reference to assure output voltage accuracy  
to be within 2% for 1.5V, 1.8V, 2.5V, 3.3.V, 5.0V and  
adjustable versions. Current limit is trimmed to ensure  
specified output current and controlled short-circuit  
current. On-chip thermal shutdown provides protection  
against any combination of overload and ambient  
temperature that would create excessive junction  
temperature.  
The CHC1084PA has an adjustable version that can  
provide the output voltage from 1.25V to 12V with only  
two external resistors.  
The CHC1084PA series is available in the industry  
standard TO252-3L package.  
Output current limiting  
Built-in thermal shutdown  
Good noise rejection  
3-Terminal Adjustable or Fixed 1.5V, 1.8V, 2.5V,  
3.3V, 5.0V  
„ APPLICATIONS  
z
z
z
z
z
z
z
z
PC Motherboard  
LCD Monitor  
Graphic Card  
DVD-video player  
NIC/Switch  
Telecom Equipment  
ADSL Modem  
Printer and other Peripheral Equipment  
„ PIN CONFIGURATION  
TO 2 5 2-3L  
3
2
1
VIN  
VOUT  
ADJ/GND  
Metal Tab VOUT  
„ BLOCK DIAGRAM  
3
INPUT  
-
+
Thermal  
Protection  
2
1
OUTPUT  
For Adjustable Output, disconnect A1 and A2, connect B  
For Fixed Output,connect A1 and A2, disconnect B  
A1  
A2  
ADJ/GND  
B
CHENMKO ENTERPRISE CO.,LTD  
CHC1084PAGP SERIES  
Low Dropout Linear Regulator  
„ ABSOLUTE MAXIMUM RATINGS (NOTE 1)  
Symbol  
VIN  
Parameter  
Input Voltage  
Rating  
12  
Unit  
V
TJ  
Maximum Junction Temperature  
150  
TS  
TLEAD  
ESD  
Storage Temperature  
Lead Temperature (10 sec.)  
ESD (Machine Model)  
-65~150  
300  
V
600  
Note 1: Stresses greater than those listed underAbsolute Maximum Ratings” may cause permanent damage to the  
device. These are stress rating only, and functional operation of the device at these or any other conditions beyond  
those indicated under “Recommended Operating Conditions” is not implied. Exposure to “Absolute Maximum  
Ratings” for extended periods may affect device reliability.  
„ RECOMMENDED OPERATING CONDITIONS  
Symbol  
VIN  
Parameter  
Input Voltage  
Rating  
12  
Unit  
V
TJ  
Operating Junction Temperature Range  
-20~150  
„ ELECTRICAL CHARACTERISTICS  
Operating Conditions: VIN10V, TJ=25, unless otherwise specified  
Parameter  
Reference  
Voltage  
Symbol  
Test Condition  
IO=10mA, VIN-VOUT=1.5V  
IO=10mA,1.5VVIN-VOUT8V  
IO=10mA, VIN=3V  
Min.  
Typ.  
Max. Unit  
1.225 1.250 1.275  
1.225 1.250 1.275  
VREF  
CHC1084PA -Adj  
CHC1084PA -1.5  
CHC1084PA -1.8  
CHC1084PA -2.5  
CHC1084PA -3.3  
CHC1084PA -5.0  
CHC1084PA-XXX  
V
V
1.485  
1.470  
1.782  
1.764  
2.475  
2.450  
3.267  
3.235  
4.950  
4.900  
1.5  
1.5  
1.8  
1.8  
2.5  
2.5  
3.3  
3.3  
5.0  
5.0  
0.2  
0.2  
1
12  
15  
20  
26  
40  
1.3  
1.515  
1.530  
1.818  
1.836  
2.525  
2.550  
3.333  
3.365  
5.050  
5.100  
0.5  
IO=10mA, 3VVIN10V  
IO=10mA, VIN=3.3V  
IO=10mA, 3.3VVIN10V  
IO=10mA, VIN=4V  
IO=10mA, 4VVIN10V  
IO=10mA, VIN=4.8V  
IO=10mA, 4.8VVIN10V  
IO=10mA, VIN=6.5V  
V
V
V
V
Output Voltage  
VOUT  
V
V
IO=10mA, 6.5VVIN12V  
IO=10mA,1.5VVIN-VOUT7V  
IO=10mA,1.5VVIN-VOUT10V  
VIN= 3V, 10mA<Io<5A  
VIN= 3V, 10mA<Io<5A  
VIN= 3.3V, 10mA<Io<5A  
VIN= 4V, 10mA<Io<5A  
VIN= 5V, 10mA<Io<5A  
VIN= 6.5V, 10mA<Io<5A  
IOUT = 5A ,VOUT=1%VOUT  
VIN-VOUT=3V  
%
%
Line Regulation  
Load Regulation  
RegLINE  
RegLoad  
0.5  
CHC1084PA -Adj  
CHC1084PA -1.5  
CHC1084PA -1.8  
CHC1084PA -2.5  
CHC1084PA -3.3  
CHC1084PA -5.0  
CHC1084PA-XXX  
CHC1084PA-XXX  
%
15  
18  
25  
33  
50  
1.5  
mV  
mV  
mV  
mV  
mV  
V
Dropout Voltage  
Current Limit  
VIN- OUT  
ILIMT  
5.1  
A
F=120Hz,COUT=25uF  
Tantalum, VIN-VOUT=3V  
Ripple Rejection  
CHC1084PA-XXX  
CHC1084PA-XXX  
60  
0.5  
70  
dB  
%
Temperature  
Stability  
IO=10mA  
CHENMKO ENTERPRISE CO.,LTD  
CHC1084PAGP SERIES  
Low Dropout Linear Regulator  
„ ELECTRICAL CHARACTERISTICS (CONTINUED)  
Operating Conditions: VIN10V, TJ=25, unless otherwise specified  
Parameter  
Adjust Pin Current  
Adjust Pin Current Change  
Minimum Load Current(ADJ)  
Quiescent Current  
Symbol  
Test Condition  
IO=10mA~5A, 1.5VVIN-VOUT10V  
IO=10mA~5A, 1.5VVIN-VOUT10V  
Min.  
Typ.  
60  
0.2  
5
5
0.3  
Max. Unit  
120  
5
µA  
µA  
mA  
mA  
%
CHC1084PA  
1.5VVIN-VOUT10V  
10  
10  
Iq  
VIN=VOUT+1.25V  
TA=125, 1000hrs  
Long-term Stability  
RMS Output Noise  
TA=25, 10Hzf10kHz  
0.003  
%
(% of VOUT  
)
Power Dissipation  
Pd  
θJA  
θJC  
W
1.6  
Thermal Resistance,  
Junction to Ambient  
/  
W
45  
/  
W
Thermal Resistance,  
Junction to case  
2.7  
Thermal Shutdown  
Thermal Shutdown  
Hysteresis  
Junction Temperature  
150  
25  
„ TYPICAL APPLICATIONS  
CHC1084PA-ADJ  
Vin Vout  
Vin  
Vout  
ADJ  
+
+
R1  
R2  
100uF  
100uF  
Vout=Vref*(1+R2/R1)+Iadj*R2  
The CHC1084PA keeps a constant 1.25V between the output pin and the adjust pin. By placing a resistor R1 across  
these two pins a constant current flows through R1, adding to the Iadj current and into the R2 resistor producing a  
voltage equal to the (1.25/R1)*R2+Iadj*R2 which will be added to the 1.25V to set the output voltage. This is  
summarized in the above equation. Since the minimum load current requirement of the CHC1084PA is 10mA, R1 is  
typically selected to be 121resistor so that it automatically satisfies the minimum current requirement. Notice that  
since Iadj is typically in the range of 50uA it only adds a small error to the output voltage and should only be  
considered when a very precise output voltage setting is required. For example, in a typical 3.3V application where  
R1=121and R2=200the error due to Iadj is only 0.3% of the nominal set point.  
CHC1084PA-5.0  
Vin=6.5V  
100uF  
5V at 5A  
Vin  
Vout  
GND  
+
+
100uF  
CHENMKO ENTERPRISE CO.,LTD  
CHC1084PAGP SERIES  
Low Dropout Linear Regulator  
„ TYPICAL APPLICATIONS (CONTINUED)  
Stability  
The CHC1084PA requires the use of an output capacitor as part of the frequency compensation in order to make the  
regulator stable. For most applications a minimum of 100uF aluminum electrolytic capacitor insures both stability  
and good transient response.  
Thermal Design  
The CHC1084PA incorporates an internal thermal shutdown that protects the device when the junction temperature  
exceeds the maximum allowable junction temperature. Although this device can operate with junction temperatures  
in the range of 150, it is recommended that the selected heat sink be chosen such that during maximum  
continuous load operation the junction temperature is kept below the temperature.  
Pd=Vout*Iout  
Tj=TA+Pd*θJA<150℃  
Layout Consideration  
The output capacitors must be located as close to the Vout terminal of the device as possible. It is recommended to  
use a section of a layer of the PC board as a plane to connect the Vout pin to the output capacitors to prevent any  
high frequency oscillation that may result due to excessive trace inductance.  
„ TYPICAL PERFORMANCE CHARACTERISTICS  
Dropout Voltage vs Output Current  
Output Voltage vs Temperature  
1.50  
1.45  
1.40  
1.35  
1.30  
1.25  
1.20  
1.15  
1.10  
1.05  
1.00  
0.95  
0.90  
2.53  
2.52  
2.51  
2.50  
2.49  
2.48  
2.47  
0.85  
0.80  
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0  
Output Current (A)  
0
25  
50  
TJ ()  
75  
100  
125  
Line Regulation vs Temperature  
Adjust Pin Current vs Output Current  
0.0  
80  
75  
70  
65  
60  
55  
50  
45  
40  
35  
30  
25  
-0.2  
-0.4  
-0.6  
-0.8  
-0.1  
20  
0
0
25  
50  
75  
TJ ()  
100  
125  
1
2
3
4
5
Output Current (A)  
CHENMKO ENTERPRISE CO.,LTD  
CHC1084PAGP SERIES  
Low Dropout Linear Regulator  
„ TYPICAL PERFORMANCE CHARACTERISTICS (CONTINUED)  
Short Circuit Current vs Dropout Voltage  
Dropout Voltage vs Temperature  
8
7
1.40  
1.35  
1.30  
1.25  
1.20  
6
5
4
3
2
1
0
0
2
4
6
8
10  
12  
0
25  
50  
75  
TJ ()  
100  
125  
Dropout Voltage (V)  
Load Transient Response  
Line Transient Response  
Vin=5.5V, Vout=2.5V Io=100mA to 5A Cin=Cout=100µF(tan)  
Vin=4.5V to 6.5V Vout=2.5V Io=200mA Cin=Cout=100µF(tan)  
CHENMKO ENTERPRISE CO.,LTD  
CHC1084PAGP SERIES  
Low Dropout Linear Regulator  
TO252-3L  
5.6  
E
b2  
2.25  
1.2  
b
e
Land Pattern Recommendation (Unit : mm)  
e1  
H
C1  
L
SEATING PLANE  
Notes:  
SEE NOTE2  
1. JEDEC Outline:TO-252 AB  
2. Mils suggested for positive contact at mounting  
Dimensions In Millimeters  
Symbol  
Dimensions In Inches  
Min.  
2.18  
1.08  
0.64  
5.23  
Nom.  
2.29  
1.15  
Max.  
2.38  
1.32  
0.78  
5.43  
Min.  
0.086  
0.043  
0.025  
0.206  
Nom.  
0.090  
0.045  
Max.  
0.094  
0.052  
0.031  
0.214  
A
A1  
b
b2  
C
C1  
D
E
e
e1  
H
L
L1  
L2  
5.35  
0.51TYP.  
0.52  
0.211  
0.020TYP.  
0.020  
0.46  
5.33  
6.38  
2.24  
4.48  
9.00  
0.51  
0.65  
1.52  
0.58  
5.80  
6.68  
2.34  
4.68  
10.40  
0.018  
0.210  
0.251  
0.088  
0.176  
0.354  
0.020  
0.026  
0.060  
0.023  
0.228  
0.263  
0.092  
0.184  
0.409  
5.57  
6.58  
0.219  
0.259  
9.70  
0.382  
0.83  
1.78  
0.95  
2.03  
0.033  
0.070  
0.037  
0.080  

相关型号:

CHC1117-2.5ZGP

Regulator,
CHENMKO

CHC1117-3.3ZGP

Regulator,
CHENMKO

CHC1117-ADJZGP

Regulator,
CHENMKO

CHC3014

X-band RX-TX Core Chip GaAs Monolithic Microwave IC
UMS

CHC3014-99F

X-band Core Chip
UMS

CHC3014-99F_15

X-band Core Chip
UMS

CHCC1

FUSE HLDR CART 600V 30A DIN RAIL
ETC

CHCC102AP

Analog Circuit
COOPER

CHCC1D

FUSE HLDR CART 600V 30A DIN RAIL
ETC

CHCC1DI

FUSE HLDR CART 600V 30A DIN RAIL
ETC

CHCC1DI-48U

Compact Modular Fuse Holders With the Industrys Best Ratings
COOPER

CHCC1DIU

Compact Modular Fuse Holders With the Industrys Best Ratings
COOPER