DOCSC010F-040.0M [CONNOR-WINFIELD]
LVCMOS Output Clock Oscillator,;型号: | DOCSC010F-040.0M |
厂家: | CONNOR-WINFIELD CORPORATION |
描述: | LVCMOS Output Clock Oscillator, 机械 振荡器 |
文件: | 总4页 (文件大小:881K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Surface Mount
Oven Stabilized Oscillator
DOCSC01-Series
OCXO or VCOCXO
Description:
Connor-Winfield’s high stability
DOCSC Series is an exceptionally
precise frequency standard, excellent
for use in cellular base stations, test
equipment, Synchronous Ethernet
and VSAT applications.
Based on an SC-cut crystal,
the DOCSC Series offers low aging and tight
stability in a 9x14mm surface mount package.
Features:
2111 Comprehensive Drive
•ꢀOCXOꢀorꢀVCOCXO
•ꢀ3.3ꢀVdcꢀOperation
•ꢀSMTꢀPackage
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630-851-5040
•ꢀFrequencyꢀStabilityꢀ±±1ꢀppb
www.conwin.com
•ꢀTemperatureꢀRanges:ꢀꢀ
ꢀ ꢀ 1ꢀtoꢀ71°C,ꢀ-21ꢀtoꢀ75°Cꢀorꢀ-41ꢀtoꢀ85°C
US Headquarters:
•ꢀLowꢀPhaseꢀNoise
630-851-4722
•ꢀLVCMOSꢀOutputꢀ
European Headquarters:
+353-61-472221
•ꢀRoHSꢀCompliantꢀ/ꢀLeadꢀFree
Suggested Pad Layout
Package Outline
0.358
(9.1mm)
0.060
(1.52mm)
0.375
(9.52mm)
0.330
(8.38mm)
0.085
(2.16mm)
0.085
(2.16mm)
0.060
(1.52mm)
DNC
0.275
(6.99mm)
4
3
2
1
0.100
(2.54mm)
0.555
(14.1mm)
Top
View
0.260
(6.60mm)
5
6
0.100
(2.54mm)
0.040
(1.02mm)
1
0.040
Keep
Out
Area
(1.02mm)
DNC
DNC = Do Not Connect
0.025
(0.64mm)
Bottom
View
Top
View
Side
View
Dimensional Tolerance: +/-0.005 (0.127mm)
Pad Connections
ꢀ ±:ꢀꢀꢀꢀꢀN/CꢀorꢀVoltageꢀControl
ꢀ 2:ꢀꢀꢀꢀꢀDoꢀNotꢀConnect*
ꢀꢀ3:ꢀꢀꢀꢀꢀGround
ꢀꢀ4:ꢀꢀꢀꢀꢀOutput
ꢀꢀ5:ꢀꢀꢀꢀꢀDoꢀNotꢀConnect*
ꢀꢀ6:ꢀꢀꢀꢀꢀSupplyꢀVoltageꢀ(Vcc)
*DOꢀNOTꢀconnectꢀ"DNC"ꢀpadsꢀtoꢀgroundꢀorꢀsupplyꢀrails.
Ordering Information
01
DOCSC
2
F
-024.576M
*ꢀNumberꢀ
Frequencyꢀ
Stability
Oscillatorꢀ
Type
Temperatureꢀ
Range
VoltageꢀControlꢀ
Option
Outputꢀꢀ
ofꢀallowableꢀ
digitsꢀafterꢀ
theꢀdecimalꢀ
point.ꢀꢀ
Frequency
1±ꢀ=ꢀ±±1.1ꢀppb
ꢀ3.3ꢀVdc
1ꢀ=ꢀ1ꢀtoꢀ71°C
±ꢀ=ꢀ-21ꢀtoꢀ75°C
2ꢀ=ꢀ-41ꢀtoꢀ85°Cꢀ
ꢀFꢀ=ꢀOCXOꢀ
(FixedꢀFreq.)
Vꢀ=ꢀVCOCXOꢀ
(VoltageꢀControlled)
FrequencyꢀFormat
-xxx.xMꢀMinꢀ*
-xxx.xxxxxxMꢀMaxꢀ*
ꢀ
LVCMOSꢀOutput
SurfaceꢀMountꢀ
OCXO
Mꢀ=ꢀMHz
Bulletin
Cx270
1 of 4
Page
Attention: System Designers please review Application Note AN2093:
System Design Information and Printed Circuit Board Layout Guidelines
for OCXO Oscillators. @ www.conwin.com/support.html
Revision
02
Date
06 May 2019
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630-851-5040
www.conwin.com
Absolute Maximum Ratings
Parameter
Minimum
Nominal
Maximum
125
Units
°C
Vdc
Vdc
Notes
Storage Temperature
Supply Voltage - 3.3 Vdc (Vcc)
Control Voltage (Vc)
-55
-
-
-
-0.5
4.5
-0.5
Vcc+0.5
Operating Specifications
Parameter
Center Frequency (Fo)
Minimum
Nominal
Maximum
Units
MHz
Notes
10
-
40
Frequency Stability vs. Change in Temperature
Option 01
-10
-
10
ppb
1
Operating Temperature Range
Option 0
0
-
70
85
1.0
20
20
5.0
0.3
3.0
3.47
°C
°C
ppm
ppb
ppb
ppb/day
ppm
ppm
Vdc
Option 2
-40
-
Frequency Calibration
-1.0
-20
-20
-5.0
-0.3
-3.0
3.13
-
2
Frequency Stability vs Load
Frequency Stability vs Voltage
Aging: Daily
-
5ꢀ
5ꢀ
3
-
-
Aging: First Year
Total Frequency Tolerance (20 Years)
Supply Voltage (Vcc)
-
-
4
5
3.30
Power Consumption Vcc = Nominal Voltage
Commercial Temperature Range: 0 to 70 °C
Turn On
-
-
-
-
2.5
1.1
W
W
Steady State @ 25°C
Industrial Temperature Range: -40 to 85 °C
Turn On
-
-
-
-
-
-
-
-
3.0
1.3
0.35
-
W
W
Steady State @ 25°C
-
Phase Jitter: (BW: 12 KHz to 5MHz @ Fo=40.0MHz)
Allan Deviation (Tau=1s)
Start-Up Time
Warm Up Time (Within Specification @ 25°C)
Warm Up Time (Within Specification @ -40°C)
0.25
3.0E-11
ps RMS
-
-
-
10
ms
s
s
60
90
CMOS Output Characteristics
Parameter
Load
Minimum
Nominal
Maximum
Units
Notes
-
15
-
pF
6
Output Voltage
Output Voltage: High (Voh)
2.7
-
-
-
-
0.3
-
4
55
6.5
V
V
Low (Vol)
Output Current: High (Ioh)
Low (Iol)
-4
-
-
mA
mA
ꢀ
-
50
-
Duty Cycle at 50ꢀ of Vcc
Rise / Fall Time: 10ꢀ to 90ꢀ
45
-
ns
Typical Phase Noise Characteristics
Parameter
Fo=10 MHz Fo=24.576MHz Fo=40.0MHz
Units
Notes
@ 1 Hz offset
-72
-70
-96
-125
-145
-151
-154
-155
-67
-90
-116
-139
-147
-153
-153
dBC/Hz
dBC/Hz
dBC/Hz
dBC/Hz
dBC/Hz
dBC/Hz
dBC/Hz
@ 10 Hz offset
@ 100 Hz offset
@ 1 KHz offset
@ 10 KHz offset
@ 100 KHz offset
@ 1MHz offset
-100
-128
-145
-151
-154
-155
Bulletin
Page
Attention: System Designers please review Application Note AN2093:
System Design Information and Printed Circuit Board Layout Guidelines
for OCXO Oscillators. @ www.conwin.com/support.html
Cx270
2 of 4
02
Revision
Date
06 May 2019
Specifications subject to change without notification. See Connor-Winfield's website for latest revision.
© Copyright 2019 The Connor-Winfield Corporation Not intended for life support applications.
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630-851-5040
www.conwin.com
Input Characteristics - Voltage Controlled Option
Parameter
Minimum
Nominal
Maximum
Units
V
ppm
Ohms
ꢀ
Notes
Control Voltage Range:
Frequency Pullability:
Input Impedance
Linearity
0.30
3.0
1.65
3.00
10.0
-
7
8
-
-
-
100K
-
5
Package Characteristics
Package consisting of a FR-4 substrate and Ryton-R-4 cover. Water Resistant package,
non-hermetic seal. (Engineering Properties of Ryton R-4 Application Note AN2100)
DOC Package
Environmental Characteristics
Shock
500 G’s 1ms, Halfsine, 3 shocks per direction, per MIL-STD 202G, Method 213B Test Condition D.
0.06” D.A. or 10G’s Peak, 10 to 500 Hz, per MIL-STD-202G, Method 204D, Test Condition A.
5.35 G’s rms. 20 to 2000 Hz per MIL-STD-202G, Method 214,Test Condition 1A, 15 minutes each axis.
10 cycles, 95ꢀ RH, Per MIL-STD-202G, Method 112.
Sinusoidal Vibration
Random Vibration
Moisture
Marking Permanency
Solder Process Recommendations:
In-line reflow:
Per MIL-STD-202G, Method 215J.
RoHS compliant, lead free. See solder profile on page 4.
Refer to recommended reflow pre-heat and reflow temperatures on page 4. Package material
consist of Ryton R-4 high temperature cover with FR4 substrate. Component solder is Pb free high
temperature eutectic alloy with a melting point of 221°C.
In-line oven profile:
We recommend using KIC profiler or similar device placing one of the thermocouples on the
device to insure that the internal package temperature does not exceed 221°C.
If for any reason the device needs to be removed from the board, use a temperature controlled
repair station with profile monitoring capabilities. Following a monitored profile will insure the
device is properly pre-heated prior to reflow. Refer to IPC 610E for inspection guidelines.
Removal of device:
Recommended Cleaning Process: (If required)
Device is non-hermetic, water resistance with four weep holes, one in each corner to allow
moisture to be removed during the drying cycle. We recommend in-line warm water wash
with air knife and drying capabilities. If cleaner does not have drying capability, then use hot air
circulated oven. Boards should be placed in the oven vertically for good water runoff.
Device must be dried properly prior to use!
Note: If saponifier is used make sure the device is rinsed properly to insure all residues are removed. PH of saponifier should
not exceed 10.
Drying Temperature:
Between 85 to 100°C.
Drying Time:
Time will vary depending on the board size.
Caution: Do not submerge the device!
Notes:
1.ꢀFrequencyꢀstabilityꢀvs.ꢀchangeꢀinꢀtemperature.ꢀ[± ±Fmaꢁꢀ-ꢀFmin)/±2*Fo)].
2.ꢀInitialꢀcalibrationꢀ@ꢀ25°C.ꢀForꢀOCXOꢀwithꢀvoltageꢀcontrolꢀoption,ꢀtheꢀcontrolꢀvoltageꢀmustꢀbeꢀfiꢁed.
3.ꢀAfterꢀ10ꢀdaysꢀofꢀoperation
4.ꢀInclusiveꢀofꢀcalibrationꢀ@ꢀ25°C,ꢀfrequencyꢀvs.ꢀchangeꢀinꢀtemperature,ꢀchangeꢀinꢀsupplyꢀvoltageꢀ±± 5ꢂ),ꢀloadꢀchangeꢀ±± 5ꢂ),ꢀshockꢀandꢀvibrationꢀ
ꢀ
andꢀ20ꢀyearsꢀaging
5ꢀ Minimumꢀ"PowerꢀOnꢀTime"ꢀafterꢀrailꢀrisesꢀfromꢀ0ꢀtoꢀwithinꢀ+/-5ꢂꢀofꢀVccꢀ=ꢀ1ꢀsecond.ꢀꢀ
Vccꢀrampꢀrateꢀmustꢀbeꢀ<0.3ꢀvoltsꢀperꢀmillisecond.ꢀ
ꢀ
6.ꢀAttention:ꢀToꢀachieveꢀoptimalꢀfrequencyꢀstability,ꢀandꢀinꢀsomeꢀcasesꢀtoꢀmeetꢀtheꢀspecificationꢀstatedꢀonꢀthisꢀdataꢀsheet,ꢀitꢀisꢀrequiredꢀthatꢀtheꢀcircuitꢀ
ꢀ
ꢀ
connectedꢀtoꢀthisꢀOCXOꢀoutputꢀmustꢀhaveꢀtheꢀequivalentꢀinputꢀcapacitanceꢀthatꢀisꢀspecifiedꢀbyꢀtheꢀnominalꢀloadꢀcapacitance.ꢀDeviationsꢀfromꢀtheꢀ
nominalꢀloadꢀcapacitanceꢀwillꢀhaveꢀaꢀgraduatedꢀeffectꢀonꢀtheꢀstabilityꢀofꢀapproꢁimatelyꢀ20ꢀppbꢀperꢀpFꢀloadꢀdifference.
7.ꢀPositiveꢀslope.ꢀ±FrequencyꢀincreasesꢀasꢀVcꢀvoltageꢀincreases).ꢀToꢀensureꢀproperꢀoperationꢀofꢀVCOCXO's,ꢀtheꢀcontrolꢀvoltageꢀinputꢀmustꢀbeꢀbiasedꢀ
theꢀnominalꢀcontrolꢀvoltage.ꢀFailureꢀtoꢀbiasꢀtheꢀVcꢀinputꢀwillꢀcauseꢀanꢀunstableꢀoutputꢀcondition.
ꢀ
8.ꢀReferencedꢀtoꢀFo.
Bulletin
Page
Attention: System Designers please review Application Note AN2093:
System Design Information and Printed Circuit Board Layout Guidelines
for OCXO Oscillators. @ www.conwin.com/support.html
Cx270
3 of 4
Revision
Date
02
06 May 2019
Specifications subject to change without notification. See Connor-Winfield's website for latest revision.
© Copyright 2019 The Connor-Winfield Corporation Not intended for life support applications.
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630-851-5040
www.conwin.com
Phase Noise Plot
Allan Deviation Plot
LVCMOS Test Circuit
RoHS Solder Profile
Temperature
260°C
260°C
DNC
Output
220°C
180°C
150°C
120°C
10uF
to
0.01uF
100 uF
2
15 pF
DNC
Pad 1
VCOCXO = Vc
OCXO = NC
DNC = Do Not Connect
DO NOT connect "DNC" pads
to ground or supply rails.
0
10 s
Up to 120 s
Typical
60 to 90 s
Typical
Meets IPC/JEDEC J-STD-020C
Tape and Reel Information
CMOS Output Waveform
1V/Div
SM-MECH51
Bulletin
Attention: System Designers please review Application Note AN2093:
System Design Information and Printed Circuit Board Layout Guidelines
for OCXO Oscillators. @ www.conwin.com/support.html
Cx270
4 of 4
02
Page
Revision
Date
06 May 2019
Specifications subject to change without notification. See Connor-Winfield's website for latest revision.
© Copyright 2019 The Connor-Winfield Corporation Not intended for life support applications.
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明