OH300-52003SV-FREQ1 [CONNOR-WINFIELD]
Sine Output Oscillator, 5MHz Min, 20MHz Max, ROHS COMPLIANT, HERMETIC SEALED, RESISTANCE WELDED PACKAGE-7;型号: | OH300-52003SV-FREQ1 |
厂家: | CONNOR-WINFIELD CORPORATION |
描述: | Sine Output Oscillator, 5MHz Min, 20MHz Max, ROHS COMPLIANT, HERMETIC SEALED, RESISTANCE WELDED PACKAGE-7 |
文件: | 总5页 (文件大小:309K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
STRATUM 3E High Stability
Oven Stabilized Oscillator
OH300 Series
OCXO – OCVCXO
Description
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630-851-5040
Connor-Winfield’s high stability OH300
OCXO / OCVCO series are exceptionally
precise frequency standard, excellent for
use in cellular base stations, test equipment,
Synchronous Ethernet, VSAT and Stratum 3E
applications
O
H
3
00-6
1238
38.88 MHz
012345689012
10
0
3C
www.conwin.com
F
012345689012
US Headquarters:
630-851-4722
European Headquarters:
+353-61-472221
These unique OCXOs and OCVCXOs
provide frequency stabilities in the range of
10 ppb to 50 ppb, over the commercial,
extended commercial or the industrial
temperature range. Power requirements are
1.1W over the commercial temperature range
and 1.5W over the industrial temperature
range after warm-up. Additionally, excellent
aging is achieved through the use of
overtone SC cut crystals.
Features
• Frequency Range: 5 to 40 MHz
• OCXO - Fixed Frequency
• OCVCXO - Voltage Controlled Frequency
• 3.3 Vdc or 5.0 Vdc Operation
• Available Frequency Stabilities:
±10.0 ppb, ±±0 ppb or ±50 ppb
• Available Temperature Ranges:
0 to 70°C, -±0 to 70°C, -±0 to 75°C,
-40 to 70°C or -40 to 85°C
• Low Phase Noise / Phase Jitter
• Output: CMOS Logic or Sinewave
• SMT Package: ±± mm x ±5 mm x 1±.7 mm
• RoHS Compliant / Lead Free
The OH300 series is available with
CMOS logic or Sinewave output along
with Electronic Frequency Tuning. These
oscillators provide outstanding phase
noise that varies depending on frequency
requirements. Allan Variance specifications
are rated for primary reference standards.
Warm up times are on the order of 5 minutes
to 0.10 ppm of final frequency.
Ordering Information
-
OH300
6
10
03
C
F
- 038.88M
Output Frequency
Package
Temperature
Range
Frequency
Stability
Supply Voltage Output Type
OCXO Type
Frequency Format
-xxxꢀxM Min
OH300- = 22x25mm
Surface Mount
Package
03 = 3ꢀ3 Vdc
05 = 5ꢀ0 Vdc
C = CMOS
S = Sinewave
F = Fixed
Freqꢀ
V = Voltage
5 = 0 to 70°C
10 = 10ꢀ0 ppb
20 = 20ꢀ0 ppb
50 = 50ꢀ0 ppb
-xxxꢀxxxxxxM Max
*Amount of
6 = -40 to 85°C
7 = -20 to 70°C
8 = -40 to 70°C
9 = -20 to 75°C
Controlled numbers after the
Freqꢀ
decimal pointꢀ
M = MHz
Example Part Number:
ꢀ OH300-61003CF-038.88Mꢀ=ꢀꢀ22x25x12.7mmꢀSMTꢀpackage,ꢀ-40ꢀtoꢀ85°Cꢀtemperatureꢀrange,ꢀ 10.0ꢀppbꢀfrequencyꢀstability,ꢀ3.3ꢀVdcꢀsupplyꢀꢀ
ꢀ
ꢀ
ꢀ
ꢀvoltage,ꢀCMOSꢀsquareꢀwaveꢀoutput,ꢀfixedꢀoutputꢀfrequencyꢀOCXO,ꢀ38.88ꢀMHzꢀoutputꢀfrequency.
ꢀ OH300-52005CV-010.0Mꢀ=ꢀ22x25x12.7mmꢀSMTꢀpackage,ꢀ0ꢀtoꢀ70°Cꢀtemperatureꢀrange,ꢀ 20.0ꢀppbꢀfrequencyꢀstability,ꢀ5.0ꢀVdcꢀsupplyꢀꢀ
ꢀ voltage,ꢀCMOSꢀsquareꢀwaveꢀoutput,ꢀvoltageꢀcontrolledꢀoutputꢀfrequency,ꢀOCVCXO,ꢀ10.0ꢀMHzꢀoutputꢀfrequency.
ꢀ OH300-75005SV-020.0Mꢀ=ꢀ22x25x12.7mmꢀSMTꢀpackage,ꢀ-20ꢀtoꢀ70°Cꢀtemperatureꢀrange,ꢀ 50.0ꢀppbꢀfrequencyꢀstability,ꢀ5.0ꢀVdcꢀsupplyꢀꢀ
ꢀ voltage,ꢀSinewaveꢀoutput,ꢀvoltageꢀcontrolledꢀoutputꢀfrequency,ꢀOCVCXO,ꢀ20.0ꢀMHzꢀoutputꢀfrequency.
Bulletin
Cx210
1 of 5
Page
Attention: System Designers please review Application Note AN2093:
System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators.
@ www.conwin.com/technologies.html
Revision
Date
09
14 Nov 2012
Specifications subject to change without notice. All dimensions in inches. © Copyright 2010 The Connor-Winfield Corporation
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630-851-5040
www.conwin.com
Absolute Maximum Ratings
Parameter
Minimum
-55
Nominal
Maximum
125
Units
°C
Vdc
Vdc
Vdc
Notes
Notes
Storage Temperature
Supply Voltage - 3ꢀ3 Vdc (Vcc)
Supply Voltage - 5ꢀ0 Vdc (Vcc)
Control Voltage (Vc)
-
-
-
-
-0ꢀ5
-0ꢀ5
-0ꢀ5
4ꢀ5
7ꢀ0
7ꢀ0
Operating Specifications
Parameter
Minimum
Nominal
Maximum
Units
MHz
Center Frequency: (Fo)
Operating Temperature Range:
Temperature Code 5
Temperature Code 6
Temperature Code 7
Temperature Code 8
Temperature Code 9
Frequency Calibration:
Frequency Stability vsꢀ Change in Temperature:
Stability Code 10
5
-
40
0
-
-
-
-
-
-
70
85
70
70
75
0ꢀ1
°C
°C
-40
-20
-40
-20
-0ꢀ1
°C
°C
°C
ppm
@ 25°C
-10ꢀ0
-20ꢀ0
-50ꢀ0
-2ꢀ0
-
-
-
-
-
10ꢀ0
20ꢀ0
50ꢀ0
2ꢀ0
ppb
ppb
ppb
ppb
ppb
1
Stability Code 20
1
Stability Code 50
1
Frequency Stability vs Load
Frequency Stability vs Voltage
Aging: Daily:
5ꢁ
5ꢁ
-2ꢀ0
2ꢀ0
5 MHz to 20 MHz
-1ꢀ0
-2ꢀ0
-
-
1ꢀ0
2ꢀ0
ppb/day
ppb/day
2
2
>20 MHz to 40 MHz
Aging: First Year:
5 MHz to 20 MHz
-50
-100
-
-
50
100
ppb
ppb
>20 MHz to 40 MHz
Lifetime Tolerance: (20 Years)
5 MHz to 20 MHz
-300
-500
-
-
300
500
ppb
ppb
3
3
>20 MHz to 40 MHz
Supply Voltage: (Vcc) (Note: Power supply turn-on ramp time must be > 5 ms to 90ꢁ of Vccꢀ)
Voltage Code 03
Voltage Code 05
3ꢀ13
4ꢀ75
3ꢀ30
5ꢀ00
3ꢀ47
5ꢀ25
Vdc
Vd
4
4
Power Consumption: Turn-On
0 to 70°C Models
-
-
-
-
-
-
-
-
3ꢀ00
3ꢀ20
3ꢀ30
3ꢀ80
W
W
W
W
5
5
5
5
-20 to 70°C Models
-20 to 75°C Models
-40 to 85°C Models
Power Consumption: Steady State @ 25°C
0 to 70°C Models
-
-
-
-
-
-
-
-
-
1ꢀ10
1ꢀ15
1ꢀ20
1ꢀ50
1ꢀ0
-
W
W
5
5
5
5
-20 to 70°C Models
-
-20 to 75°C Models
-
W
-40 to 85°C Models
-
W
Phase Jitter: (BW: 10 Hz to Fo/2)
Short Term Allan Deviation (1s)
Start-Up Time:
-
ps rms
rms
ms
1ꢀ0E-11
-
-
500
5
Warm Up Time @ 25°C:
minutes
6
Phase Noise Characteristics
Typical Phase Noise for 10 MHz OXCO's with CMOS Output
Parameter
Minimum
Nominal
Maximum
-85
Units
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Bulletin
Notes
@1Hz offset
-
-
-
-
-
-
-
-
-
-
-
-
@ 10Hz offset
@ 100Hz offset
@ 1KHz offset
@ 10KHz offset
@ 100KHz offset
-115
-140
-145
-150
-150
Cx210
2 of 5
09
Page
Revision
Date
14 Nov 2012
Specifications subject to change without notice. All dimensions in inches. © Copyright 2010 The Connor-Winfield Corporation
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630-851-5040
www.conwin.com
OCVCXO Input Characteristics (OCXO Type Code V)
Parameter
Minimum
Nominal
Maximum
Units
Notes
Control Voltage Range: (Vc)
3ꢀ3 Vdc Models
5ꢀ0 Vdc Models
Frequency Pullability:
Input Impedance
0ꢀ30
0ꢀ50
0ꢀ4
1ꢀ65
2ꢀ50
-
-
3ꢀ00
4ꢀ50
-
-
V
V
7
7
ppm
Ohms
100K
CMOS Output Characteristics (Output Code C)
Parameter
Minimum
Nominal
Maximum
Units
pF
Notes
Load
-
15
-
Output Voltage:
3ꢀ3 Vdc Models High (Voh)
3ꢀ0
-
4ꢀ7
-
45
-
-
-
-
-
-
50
-
-
-
V
V
Low (Vol)
0ꢀ4
-
5ꢀ0 Vdc Models High (Voh)
Low (Vol)
Duty Cycle at 50ꢁ of Vcc
Rise / Fall Time: 10ꢁ to 90ꢁ
Spurious Output
0ꢀ4
55
6
ꢁ
ns
dBc
-80
Sinewave Output Characteristics (Output Code S)
Parameter
Load
Output Power
Harmonics
Spurious
Minimum
Nominal
Maximum
Units
Ohms
dBm:
dBc
Notes
-
5ꢀ0
-
50
-
-
-
-
-
-30
-80
-
dBc
Package Characteristics
OH300 Package
Package consisting of a FR4 substrate and Ryton-R4 coverꢀ Water Resistant package,
non-hermetic sealꢀ
Recommended Cleaning Process
Wash only in a in-line high pressure wash station that has an air knife and drying capabilitiesꢀ
(Drying temperature range from 85° to 100°C)
Environmental Characteristics
Shock
500 G’s 1ms, Halfsine, 3 shocks per direction, per MIL-STD 202G, Method 213B Test Condition Dꢀ
0ꢀ06” DꢀAꢀ or 10G’s Peak, 10 to 500 Hz, per MIL-STD-202G, Method 204D, Test Condition Aꢀ
5ꢀ35 G’s rmsꢀ 20 to 2000 Hz per MIL-STD-202G, Method 214,Test Condition 1A, 15 minutes each axisꢀ
10 cycles, 95ꢁ RH, Per MIL-STD-202G, Method 112ꢀ
Sinusoidal Vibration
Random Vibration
Moisture
Marking Permanency
Solder Process
Per MIL-STD-202G, Method 215Jꢀ
RoHS compliant, lead freeꢀ See solder profileꢀ
Re-Stabilization Time
Off Time
<1 Hour
Re stabilization Time
<2 Hours *
<6 Hour
<12 Hours *
<48 Hours *
48 Hours + 1/4 Off Time *
<6 Days *
<24 Hour
1 to 16 Days
>16 Days
* For a given off time, the time required to meet daily aging, short term stability requirementsꢀ
Notes:
ꢀ 1.ꢀReferencedꢀtoꢀtheꢀfrequencyꢀmeasuredꢀ@ꢀ25°C.ꢀOCVCXOꢀcontrolꢀvoltageꢀ(Vc)ꢀ=ꢀnominalꢀvoltage.
ꢀ 2.ꢀAtꢀtimeꢀofꢀshipmentꢀafterꢀ48ꢀhoursꢀofꢀoperation.
ꢀ 3.ꢀInclusiveꢀofꢀcalibration,ꢀoperatingꢀtemperature,ꢀsupplyꢀvoltageꢀchange,ꢀloadꢀchangeꢀandꢀ20ꢀyearsꢀaging.
ꢀ 4.ꢀMinimumꢀ"PowerꢀOnꢀTime"ꢀafterꢀrailꢀrisesꢀfromꢀ0ꢀtoꢀwithinꢀ+/-5%ꢀofꢀVccꢀ=ꢀ1ꢀsecond.ꢀꢀ
ꢀ ꢀ Vccꢀrampꢀrateꢀmustꢀbeꢀ<0.3ꢀvoltsꢀperꢀmillisecond.ꢀ
Bulletin
Page
Cx210
3 of 5
ꢀ 5.ꢀMeasuredꢀwithꢀVccꢀ=ꢀNominal,ꢀinꢀcalmꢀair.
ꢀ 6.ꢀMeasuredꢀ@ꢀ25°C,ꢀwithinꢀ 100ꢀppb,ꢀreferencedꢀoneꢀhourꢀafterꢀturn-on.
ꢀ 7.ꢀToꢀensureꢀproperꢀoperationꢀofꢀOCVCXO'sꢀtheꢀcontrolꢀvoltageꢀinputꢀmustꢀbeꢀbiasedꢀtheꢀnominalꢀcontrolꢀvoltage.ꢀFailureꢀꢀ
ꢀ ꢀ toꢀbiasꢀtheꢀVcꢀinputꢀwillꢀcauseꢀanꢀunstableꢀoutputꢀcondition.ꢀ
Revision
Date
09
14 Nov 2012
Specifications subject to change without notice. All dimensions in inches. © Copyright 2010 The Connor-Winfield Corporation
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630-851-5040
www.conwin.com
Attention: System Designers please review Application Note AN2093:
System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators.
@ www.conwin.com/technologies.html
Package Outline
0.866+/-0.008
(22.00+/-0.20mm)
0.300
(7.62mm)
0.200
(5.08mm)
(
I
W
1238
OH300-61003CF
38.88 MHZ
1.000+/-0.008
(25.40+/-0.20mm)
0123456789012
0123456789012
(Bottom View)
0.350
(8.89mm)
Pin 1
Typical Pad Size
0.700
(17.78mm)
0.100 x 0.100
(2.54 x 2.54mm)
7 Places
0.062
(1.57mm)
0.500
(12.70mm)
Max.
Dimensional Tolerance
+/-0.005 (0.127mm)
Pad Termination Finish: Gold Flash <10 micro inches
Marking Information
Suggested Pad Layout
0.300
0.200 0.200
(5.08mm)
(7.62mm)
(5.08mm)
0.150
(3.81mm)
0.125
(3.175mm)
Typ.
(
I
W
Date Code (YYWW)
1238
0.120
(3.048mm)
Typ.
Model Number
Output Frequency
Serial # Barcode
Serial Number
OH300-61003CF
38.88 MHZ
0.905
(22.99mm)
0123456789012
0123456789012
(Top View)
Keep Out
Area
0.350
(8.89mm)
0.350
(8.89mm)
Pin 1
•
* Do not route any traces in the keep out areaꢀ It is recommended
the next layer under the keep out area is to be ground planeꢀ
Test Circuit CMOS Output
Pad Connections
Control
Voltage
or
Frequency
Counter
Vcc
N/C
Ground
DNC
1: Control Voltage or N/C
2: N/C
3: Supply Voltage (Vcc)
4: RF Output
5: Do Not Connect
6: Do Not Connect
7: Ground (Case)
Power
Supply
1
7
6
N/C
DNC
2
3
10uF
to
100 uF
5
-
+
0.01 uF
15 pF
Vcc
4
RF Out
DNC = Do Not Connect
Scope
Ground
Test Circuit Sinewave Output
Control
Voltage
or
Frequency
Counter
Vcc
N/C
Ground
DNC
Power
Supply
1
7
6
N/C
DNC
2
3
10uF
to
100 uF
50
Ohm
5
-
+
0.01 uF
Vcc
4
RF Out
Bulletin
Cx210
4 of 5
09
DNC = Do Not Connect
Scope
Page
Revision
Date
14 Nov 2012
Ground
Specifications subject to change without notice. All dimensions in inches. © Copyright 2010 The Connor-Winfield Corporation
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630-851-5040
www.conwin.com
CMOS Output Waveform
90%
50%
10%
Solder Profile
Temperature
260°C
260°C
220°C
180°C
150°C
120°C
0
10 s
Up to 120 s
60 to 90 s
Typical
Typical
Meets IPC/JEDEC J-STD-020C
Tape and Reel Information
Rev P00, New issueꢀ 01/26/11ꢀ
Rev P01, Added tape and reel informationꢀ 05/04/11ꢀ
Rev P02, Added OH300 Photoꢀ 05/06/11ꢀ
Rev P03, updated the Descriptionꢀ 05/25/11ꢀ
Rev P04, Updated power consumption and changed package drawingꢀ 07/27/11ꢀ
Rev P05, Added sinewave models to the data sheet 09/08/11ꢀ
Rev P06, added cleaning process and package characteristicsꢀ 08/09/12ꢀ
Rev 07, added Barcode to package markingꢀ 09/27/12
Rev 08, Added link to Application Note: AN2093ꢀ 11/06/12
Rev 09, Added additional notesꢀ 11/14/12ꢀ
Bulletin
Cx210
5 of 5
Page
Revision
09
Date
14 Nov 2012
Specifications subject to change without notice. All dimensions in inches. © Copyright 2010 The Connor-Winfield Corporation
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明