RI-01B [COTO]

Dry Reed Switch; 干簧开关
RI-01B
型号: RI-01B
厂家: COTO TECHNOLOGY    COTO TECHNOLOGY
描述:

Dry Reed Switch
干簧开关

开关
文件: 总2页 (文件大小:212K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
RI-01B Series Dry Reed Switch  
RI-01B Series  
Micro dry-reed switch hermetically sealed in a gas-filled envelope.  
Single-pole, single-throw (SPST) type, having normally open contacts,  
and containing two magnetically actuated reeds.  
The switch is of the double-ended type and may be actuated by an  
electromagnet, a permanent magnet or a combination of both.  
The device is intended for use in sensors, relays, pulse counters or  
similar devices.  
RI-01B Series Features  
Ideal for general purpose reed relays and sensors  
Contact layers: ruthenium on gold  
Superior glass-to-metal seal and blade alignment  
Dimensions in inches (mm)  
General data for all models RI-01B  
AT-Customization / Preformed Leads  
Besides the standard models, customized products  
can also be supplied offering the following options:  
! Operate and release ranges to customer  
specification  
End of life criteria:  
Contact resistance > 1after 2 ms  
Release time > 2 ms (latching or contact sticking).  
Loaded conditions (resistive load: 12 V; 4 mA;  
(15 mA peak); operating frequency: 170 Hz)  
Life expectancy: min. 106 operations.  
! Cropped and/or preformed leads  
Coils  
End of life criteria:  
All characteristics are measured using the Philips  
Standard Coil. For definitions of the Philips Stan-  
dard Coil, refer to “Application Notes” in the Reed  
Switch Technical & Application Information Section of  
this catalog.  
Contact resistance > 2after 4 ms  
Release time > 0.7 ms (latching or contact sticking).  
Switching different loads involves different life expect-  
ancy and reliability data. Further information is avail-  
able on request.  
Life expectancy and reliability  
Mechanical Data  
The life expectancy data given below are valid for a  
coil energized at 1.25 times the published maximum  
operate value for each type in the RI-01B series.  
Contact arrangement is normally open; lead finish is  
tinned; net mass is approximately 190 mg; and can be  
mounted in any position.  
No load conditions (operating frequency:  
100Hz)  
Shock  
The switches are tested in accordance with  
“IEC 68-2-27”, test Ea (peak acceleration 150 G, half  
Life expectancy : min. 108 operations with a failure  
rate of less than 10-9 with a confidence level of 90%.  
COTO TECHNOLOGY (USA) Tel: (401) 943-2686 / Fax (401) 942-0920  
6
(Europe) Tel: +31-45-5439343 / Fax +31-45-5427216  
136  
RI-01B Series Dry Reed Switch  
* The Contact Resistance is measured using the Kelvin Method next to the glass body.  
sinewave; duration 11 ms). Such a shock will not cause  
an open switch (no magnetic field present) to close,  
nor a switch kept closed by an 80 AT coil to open.  
Soldering  
The switch can withstand soldering heat in accordance  
with “IEC 68-2-20”, test Tb, method 1B: solder bath at  
350 10°C for 3.5 0.5 s. Solderability is tested in  
accordance with “IEC 68-2-20”, test Ta, method 3:  
solder globule temperature 235°C; ageing 1b: 4 hours  
steam.  
Vibration  
The switches are tested in accordance with “IEC  
68-2-6”, test Fc (acceleration 10G; below cross-over  
frequency 57 to 62 Hz; amplitude 0.75 mm;  
frequency range 10 to 2000 Hz, duration 90 minutes).  
Such a vibration will not cause an open switch (no  
magnetic field present) to close, nor a switch kept  
closed by an 80 AT coil to open.  
Welding  
The leads can be welded.  
Mounting  
The leads should not be bent closer than 1 mm to the  
glass-to-metal seals. Stress on the seals should be  
avoided. Care must be taken to prevent stray magnetic  
fields from influencing the operating and measuring  
conditions.  
Mechanical Strength  
The robustness of the terminations is tested in accor-  
dance with “IEC 68-2-21”, test Ua1 (load 40 N).  
Operating and Storage Temperature  
Operating ambient temperature; min: -55°C;  
max: +125°C. Storage temperature; min: -55°C; max:  
+125°C. Note: Temperature excursions up to 150°C  
may be permissible. For more information contact your  
nearest Coto Technology sales office.  
For Most Recent Data, Consult the Coto Technology Website: www.cotorelay.com  
6
E-mail: sales@cotorelay.com  
137  

相关型号:

RI-01BA

Dry Reed Switch
COTO

RI-01BAA

Dry Reed Switch
COTO

RI-01BAAA

Dry Reed Switch
COTO

RI-01C

Dry Reed Switch
COTO

RI-01CA

Dry Reed Switch
COTO

RI-01CAA

Dry Reed Switch
COTO

RI-01_07

Machine Inertable Type Dip Switch
DBLECTRO

RI-02

Machine Inertable Type Dip Switch
DBLECTRO

RI-02

Dry Reed Switch
COTO

RI-02-H-T

MACHINE INSERTABLE TYPE DIP SWITCH
DBLECTRO

RI-02-S-T

MACHINE INSERTABLE TYPE DIP SWITCH
DBLECTRO

RI-02SMD

Dry Reed Switch
COTO