T02KO [CPI]
250 W Outdoor TWT Power Amplifier; 250W的户外行波管功率放大器
| 型号： | T02KO |
| 厂家： | 
COMMUNICATIONS & POWER INDUSTRIES, INC. |
| 描述： | 250 W Outdoor TWT Power Amplifier |
| 文件： | 总2页 (文件大小：159K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
250 W Outdoor TWT Power Amplifier
for Satellite Communications
Ka-Band
The T02KO Series
250 watt peak
power TWT
Amplifier—
Environmentally
sealed compact
design for outdoor
operation
Plays in the Rain
Global Applications
Rugged, compact and lightweight amplifier
designed for outdoor use.
Meets International Safety Standard EN-
60215, Electromagnetic Compatibility 89/336/
EEC and Harmonic Standard EN-61000-3-2 to
satisfy worldwide requirements.
Efficient and Cost Effective
Mounting at the antenna improves
performance through minimized cable losses
and saves cost in system design. Employs
a high efficiency helix traveling wave tube,
reducing operating costs.
Worldwide Support
Backed by over three decades of satellite
communications experience, and CPI’s
worldwide 24-hour customer support
network that includes fifteen regional factory
Service Centers.
Simple to Operate
User-friendly microprocessor-controlled logic
with integrated RS422/485 computer interface.
Digital metering is standard.
811 Hansen Way
P.O. Box 51625, Palo Alto, CA 94303
Easy to Maintain
Modular design and built-in fault diagnostic
capability via remote monitor and control.
tel: +1 (650) 846-3803
fax: +1 (650) 424-1744
e-mail: marketing@satcom.cpii.com
www.cpii.com/satcom
Ka-Band
SPECIFICATIONS
T02KO Series
Electrical
Frequency
User-specified frequency range within the 27.5 to 31.0 GHz band, as limited by bandwidth capability of amplifier1
Output Power
250 W (53.98 dBm) peak
120 W (50.8 dBm) or 175 W (52.4 dBm)
Average Power (TWT)
CW Power (Flange)
Bandwidth
100 W (50.0 dBm) or 145 W (51.6 dBm)
1000 - 2500 MHz, depending on desired frequency range1
O P T I O N S :
Gain
• 1 RU Remote
Control Panel
at rated power
at small signal
70 dB min.
75 dB min. (SSIPA can be removed as an option. SSG without SSIPA is 50 dB min.)
• Internal Switch
Control and
Drive
RF Level Adjust Range
Attenuator Step Size
Small Signal Gain Slope
Small Signal Gain Variation
Gain Stability (at constant
drive and temperature)
VSWR
0 to 25 dB
0.1 dB
0.04 dBꢀMHz maꢁ.
• Redundant or
Power Combined
Subsystems
1.0 dB pk-pk maꢁ. across any 40 MHz segment; 2.5 dB pk-pk maꢁ. across passband
0.25 dBꢀ24 hours maꢁ. (after 30 minute warm-up)
1.0 dB over temperature range
• Integral
Linearized Solid
State IPA (LIPA)
1.3:1
Input
1.3:1
Output
1.5:1 maꢁ. full spec. compliance; 2.0:1 maꢁ. continuous; any value for operation without damage
Load
• Integral Block
Upconverter
12 dB below IESS 308 continuous mask
Phase Noise
(refer to T02KO
B-Series TWTA)
2.5˚ ꢀdB maꢁ. for a single carrier up to 6 dB OBO(1.0˚ꢀdB maꢁ. up to 3 dB OBO with optional linearizer)
AM/PM Conversion
Noise Power Density
<-150 dBWꢀ4 kHz, below 21.2 GHz
<-70 dBWꢀ4 kHz, transmit band (<-65 dBWꢀ4 kHz, transmit band with linearizer)
• Ethernet Interface
Noise Figure
Intermodulation
Group Delay
Linear
10 dB maꢁ. (12 dB maꢁ. with linearizer)
-23 dBc or better with 2 equal carriers at total power level 50 W or 72.5 W CW (100 W or 140 W with linearizer)
In any 40 MHz band
0.01 nsecꢀMHz maꢁ.
Parabolic
0.001 nsecꢀMHz sq. maꢁ.
0.5 nsec pk-pk maꢁ.
Ripple
Primary Power
Power Consumption
Power Factor
100-240 VAC 10ꢂ, single phase, 47-63 Hz
800 VA maꢁ., 650 VA typ.
0.95 min.
Environmental (operating)
Ambient Temperature
Relative Humidity
-40˚ to +60˚ C, with eꢁtra margin for solar loading
100ꢂ condensing
Altitude
10,000 ft with standard adiabatic derating of 2˚ Cꢀ1000 ft
20 g pk, 11 msec, 1ꢀ2 sine ꢀ 2.1 grms, 5 to 500 Hz
Shock and Vibration
Mechanical
Cooling
Forced air with integral blower
WR-28F
RF Input Connection
RF Output Connection
RF Output Monitor
Dimensions (WxHxD)
Weight
WR-34G (WR-28G optional)
2.9 mm SMA Female
10.25 ꢁ 9.5 ꢁ 20 inches (261 ꢁ 242 ꢁ 508 mm)
52 lbs. (23.6 kg) maꢁ.
Heat and Acoustic
Heat Dissipation
Acoustic
500 W maꢁ.
65 dBA typ. (as measured at 3 feet from unit)
Note 1: Please consult CPI representative to confirm that desired bandwidth is available over desired frequency range.
Mounting hardware is provided with each amplifier.
KEEPINGYOU ONTHE AIR
not up in the air
Certificate Number: 30515
For more detailed information, please refer to the corresponding CPI Technical Description.
Note: Specifications may change without notice as a result of additional data or product refinement.
Please contact CPI before using this information for system design.
MKT 98, ISSUE 15
6/07
PDF
相关型号：
©2020 ICPDF网 联系我们和版权申明