CA12514-RITA-A [CREE]
Rita series; 丽塔系列
| 型号： | CA12514-RITA-A |
| 厂家： | 
CREE, INC |
| 描述： | Rita series |
| 文件： | 总7页 (文件大小：504K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
PRODUCT DATASHEET
Rita series
last update 4/9/2012
Ordering number C12512_RITA-A
Family
Rita
FWHM
Asym degrees
85 %
Type
Reflector
XM-L
Efficiency
cd/lm
LED
0.600
Color
White
Gerber File
Available
Diameter
Height
36+28.4 mm
17.1 mm
Rectangular
PC
Style
Optic Material
Holder Material
Fastening
Status
-
Pin, glue
Ready
Ordering number CA12514_RITA-A
Family
Rita
FWHM
Asym degrees
85 %
Type
Reflector
XM-L
Efficiency
cd/lm
LED
0.600
Color
White
Gerber File
Available
Diameter
Height
36 + 28.4 mm
17.3 mm
Rectangular
PC
Style
Optic Material
Holder Material
Fastening
Status
-
Pin, tape
Ready
NOTE: The typical divergence will be changed by different color, chip size and chip position
tolerance. The typical total divergence is the full angle measured where the luminous intensity
is half of the peak value.
September 14th 2012 18:53 Copyright Ledil Oy - Subject to change without prior notice - Page 1/2
Ledil Oy
http://www.ledil.com
Salorankatu 10
24240 SALO
Finland
email: ledil@ledil.com
FAX: +358-2-733 8001
PRODUCT DATASHEET
Rita series
last update 4/9/2012
GENERAL INFORMATION
- Product series especially designed & optimized for XM-L series of LEDs.
- Special care taken to make light distribution as uniform as possible.
- Reflector is made of aluminium coated PC (120 degrees of Celcius / 248 degrees of Fahrenheit) with
protective lacquer (110 degrees of Celcius / 230 degrees of Fahrenheit).
- Fastening to heat sink with a PU foam adhesive tape of automotive grade. Please find fastening details by
clicking link: http://www.ledil.com/datasheets/DataSheet_TAPE.pdf
- Fastening to PCB with appropriate adhesive. By clicking link below you can find Ledil recommended glue
options.
http://www.ledil.com/datasheets/DataSheet_GLUES.pdf
NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the end
product. For example, mechanical stress, vibration and holes on the surface of the circuit boar
weaken the strength of the tape.
NOTE 2: Assembly to the surface must be made straight, so the tape bonds constant and
balanced with fastening surface. Slanted assembly might cause unbalanced bond to the
surface. All surfaces where tape is applied must be clean, dry and free from grease and dirt.
If cleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of your
LED manufacturer - this is important as cleaning shall under no circumstances damage LEDs or
other electronics components on the PCB.
Further note that optical components shall not be cleaned with any chemicals - only micro fiber
cloth may be used to remove fingerprints or other traces from handling.
NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the end
product. For example, mechanical stress, vibration and holes on the surface of the circuit boar
weaken the strength of the glue.
NOTE 2: All surfaces where glue is applied must be clean, dry and free from grease and dirt. If
cleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of your LED
manufacturer -this is important as cleaning shall under no circumstances damage LEDs or other
electronics components on the PCB.
Further note that optical components shall not be cleaned with any chemicals - only micro fiber
cloth may be used to remove fingerprints or other traces from handling.
September 14th 2012 18:53 Copyright Ledil Oy - Subject to change without prior notice - Page 2/2
Ledil Oy
http://www.ledil.com
email: ledil@ledil.com
FAX: +358-2-733 8001
Salorankatu 10
24240 SALO
Finland
相关型号：
©2020 ICPDF网 联系我们和版权申明