DR2260A20VRJ [CRYDOM]
DIN Rail Mount;型号: | DR2260A20VRJ |
厂家: | CRYDOM INC., |
描述: | DIN Rail Mount |
文件: | 总2页 (文件大小:790K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
InstallationDISN RhaileMeoutnt
PART NUMBER NOMENCLATURE
Rated Load Current
20: 20 Amps
Switching Type
30: 30 Amps
Blank: Zero Voltage Turn-On
R: Instantaneous Turn-On
(AC Output only)
Operating Voltage
20: 1-200 VDC
60: 48-600 VAC
35: 35 Amps [High I2t]
(AC Output only)
DR22 Series Solid State Relays
Series
Crydom DR22 Series Solid State Relays were developed to offer the advantages of
semiconductor switching technology in a standard 22.5 mm industrial package. Quick and easy
installation is coupled with low drive power requirements and efficient, reliable power SCR
output. This compact new design offers up to 35 ARMS in ambient temperatures of 40ºC.
DR22
60
A
20
V
R
J
Control Voltage
Terminal Layout
Input Connector
A: 90-280 VAC/VDC
(AC Output only)
D: 4-32 VDC
U: Relay Configuration
V: Contactor
Blank: Screw Terminal
J: Spring Terminal
(V and W suffixes only)
Be sure to visit the product series datasheet available at the Crydom website to complement this
information. If you have questions or need additional information please contact Crydom Tech
Support.
Configuration
AC
Output
only
(std. screw)
W: Contactor
Configuration
(elevator screw)
Please read all instructions before using your DIN Rail Mount Solid State Relay (SSR).
Required for valid part number
For options only and not required for valid part number
MOUNTING INSTRUCTIONS
Install the relay on the DIN Rail (as shown in fig. 1)
To install
on DIN rail
■
WIRING DIAGRAMS
■
Maximum recommended terminal screw torque input
terminal:
Relay AC
Contactor AC
Relay DC (A)
To remove
from DIN rail
(-
/
)
(
-
)
(+ /
)
(+)
♦Contactor configuration (”V” & “W” suffixes):
5 in-lb (0.5 Nm)
V
AC
♦Relay configuration (”U” suffix):
13-15 in-lb (1.5-1.7 Nm)
1/L1
+3/A1
-4/A2
+3/A1
-4/A2
■
Maximum recommended terminal screw torque load
fig. 1 SSR mounted on DIN rail
(-/ )
)
(+ /
terminal:
INPUT
STATUS
INPUT
STATUS
♦Contactor configuration (”V” & “W” suffixes): 18-20 in-lb (2.0-2.2 Nm)
♦Relay configuration (”U” suffix): 13-15 in-lb (1.5-1.7 Nm)
INPUT
STATUS
+3/A1 -4/A2
Load
■
■
If multiple units are installed be sure to follow derating curves
Recommended wire sizes as shown in TABLE 1
WARNING! Removing product from 35 mm rail incorrectly by not using the appropriate tool
1/L1
2/T1
+1
-2
would damage the latching system.
2/T1
+
AC
V
TABLE 1. Recommended Wire Sizes
+
V
-
Load
(B)
Load
Terminal
Configuration
Wire Size
(Solid / Stranded)
Wire Pull-Out
Strength (lb)[N]*
2
2 x 18 AWG (1 mm ) Stranded [minimum]
20 [88]
60 [266]
20 [88]
40 [177]
25 [111]
80 [355]
90 [400]
4.5 [20]
30 [133]
5 [22]
Output
Relay “U” suffix
■
Important Considerations
♦Be sure to use input and output voltages within
2
2 x 10 AWG (6 mm ) Stranded [maximum]
0.89 in [22.5 mm]
Minimum
2
operating ranges.
2 x 18 AWG (1 mm ) Stranded
Input
Relay “U” suffix
♦LED indicates only input status. It does not
represent output status.
♦To achieve maximum ratings, there must be a
minimum spacing of 0.89 in (22.5 mm) between the
devices in free air (as shown in fig.2).
2
2 x 12 AWG (4 mm ) Stranded
2
Output
Contactor
“V” &“W”
suffixes
2 x 20 AWG (0.75 mm ) [minimum]
2
2 x 10 AWG (6 mm )
2
2 x 8 AWG (10 mm ) [maximum]
♦Protective Earth (PE) screw type recommended is
10-32 UNC standard, not provided with SSR. Through
the use of a DIN rail ground (protective conductor)
terminal block, the DIN rail itself can be used as the
grounding bus bar. In this case, the zinc plated steel
material used for the DIN rail clip of DR22 models,
permits a secure path to ground and avoid the need of
a further PE connection (see fig.3).
2
30 AWG (0.05 mm ) [minimum]
Input
Screw
Spring
2
12 AWG (3.3 mm ) [maximum]
Contactor
“V” &“W”
suffixes
fig. 2 Multiple units
mounting
for maximum
ratings
2
26 AWG (0.13 mm ) [minimum]
fig. 3 DR22 model
with Protective
Earth screw
2
12 AWG (3.3 mm ) [maximum]
5 [22]
* Tests performed on Stranded wire
TABLE 3. Recommended Accessories
TABLE 2. Compatible Terminals
W
D
W D
Terminals
Fork Lug
Ring Lug
Copper Lug
Copper Lug
Connectors
ID Marker
Lug Terminal
Crydom Part No.
TRM0
TRM6
CP201
CP202
CNLB
CNLN
CNL2
TRM0
TRM6
Width [W] in (mm)
Stud Size Dia [D] (in)
Wire Size AWG
0.45 (11.4)
#8 (0.168)
0.45 (11.4)
#8 (0.168)
6-0
14-6
General Notes
(A) Load can be wired to either terminal 1 or terminal 2. Proper polarity must be observed for the DC control power supply, with terminal 3 being positive with respect to terminal 4.
(B) DC inductive loads must be diode suppressed.
(C) AC input models operating range is -20 to 60 ºC
Rev. 060816
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
InstallationDISN RhaileMeoutnt
ELEVATOR SCREW (”W” SUFFIX) CONSIDERATIONS
PIN TERMINAL CONSIDERATIONS
■
■
The Elevator Screw option allows the screw and clamp to
For 35 Amp Relay configuration (suffix "U") models
be raised out of the mating threads completely. This
provides for the insertion and use of a ring or lug type wire
terminal.
use Pin Terminals (L 0.410 in x Ø 0.102 in) to install 8 AWG
wire.
■
To install, make sure screw is completely lifted to
■
A #2 Phillips head driver should be used with the Elevator
maximum position, and insert Pin terminal (as shown in
fig. 5)
Screws. If a powered driver is used, avoid speeds above 500
RPM.
■
Once installed, tighten terminal screws. Maximum
■
Cutting threads in the cover plastic as the screw elevates
recommended screw torque is 14 in-lb(1.58 Nm). Be sure
to apply sufficient downward pressure while tightening
the terminal screws to prevent the screw assembly from
lifting.
is key to the elevating feature. It has a finite life and
therefore not recommended to be used more than 50 times
during the product lifetime.
■
Do not continue rotating the screw (in the elevating
fig. 4 Elevator screw
direction) once it freely rotates at the top of the plastic
surface. The Elevator screw is capable of clearing 0.125
inches between the terminal and the bottom of the screw.
Insertion of a terminal or lug thicker than 0.125 in is not
recommended.
■
During tightening, be certain that the terminal is seated
flat within the cavity, and that the clamping washer is
secure against the upper surface of the terminal.
■
If fork terminations, spade lugs, or stranded wire are
■
used, to prevent improper contact do not raise the elevator
screw out of the mating threads.
When inserting the terminal ensure that the terminal hole
is in line with the screw.
fig. 5 Pin Terminal
DERATING CURVES(C)
DR2260x20x
DR2260x35x
DR2260x30x
20
35
30
25
20
15
10
5
30
25
20
15
10
5
15
10
5
0
0
0
20
30
40
50
60
70
80
20
30
40
50
60
70
80
20
30
40
50
60
70
80
Ambient Temperature (ºC)
Ambient Temperature (ºC)
Ambient Temperature (ºC)
DR2220D30U
DR2220D20U
30
25
20
15
10
5
20
15
10
5
Single unit
Multiple units, no minimum spacing
between components (see fig. 2)
0
0
20
30
40
50
60
70
80
20
30
40
50
60
70
80
Ambient Temperature (ºC)
Ambient Temperature (ºC)
DANGER / DANGER / GEFARH / PELIGRO / PERICOLO /
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
RISQUE D'ELECTROCUTION, D'EXPLOSION OU D'ARC ELECTRIQUE
STROMSCHLAG-, EXPLOSIONS- ODER LICHTBOGENGEFAHR
• Turn off power supply before working on this equipment.
• Coupez l'alimentation avant de travailler sur cet appareil.
• Vor dem Arbeiten an dem Gerät dessen Stromversorgung abschalten.
Le non-respect de ces instructions provoquera la mort ou des blessures
graves.
Die Nichtbeachtung dieser Anweisungen führt zu Tod oder schwerer
Körperverletzung.
Failure to follow these instructions will result in death or
serious injury.
RISCHIO DI SCOSSA ELETTRICA, DI ESPLOSIONE O DI OFTALMIA DA FLASH
RIESGO DE ELECTROCUCIÓN, EXPLOSIÓN O ARCO ELÉCTRICO
存在电击、爆炸或电弧闪烁危险
• 在操作此设备之前请先关闭电源。
Desconecte toda alimentación antes de realizar el servicio.
• Scollegare l'apparecchio dalla presa di corrente prima di qualsiasi intervento.
Si no se siguen estas instrucciones provocará lesiones graves
o incluso la muerte.
Il mancato rispetto di queste istruzioni provocherà morte o
gravi infortuni.
若不遵守这些说明,可能会导致严重的人身伤害甚至死亡。
WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告
RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE
• The product's side panels may be hot, allow the product to cool before
touching.
RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER
• Les panneaux latéraux du produit peuvent être chauds. Laisser le produit
refroidir avant de le toucher.
GEFAHR VON MATERIALSCHÄDEN UND GEHÄUSEERHITZUNG
• Die Seitenwände können heiß sein. Lassen Sie das Produkt abkühlen,
bevor Sie es berühren.
• Follow proper mounting instructions including torque values.
• Do not allow liquids or foreign objects to enter this product.
• Respecter les consignes de montage, et notamment les couples de serrage.
• Ne pas laisser pénétrer de liquide ni de corps étrangers à l'intérieur du produit.
• Beachten Sie die Montageanweisungen,
• Führen Sie keine Flüssigkeiten oder Fremdkörper in das Produkt ein.
Failure to follow these instructions can result in
serious injury, or equipment damage.
Le non-respect de cette directive peut entraîner, des lésions corporelles
graves ou des dommages matériels.
Die Nichtbeachtung dieser Anweisung kann Körperverletzung oder
Materialschäden zur Folge haben.
RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO
• I pannelli laterali dell'apparecchio possono scottare; lasciar quindi raffreddare
il prodotto prima di toccarlo.
RIESGO DE DAÑOS MATERIALES Y DE SOBRECALENTAMIENTO
DE LA UNIDAD
• Los paneles laterales del producto pueden estar calientes. Esperar que
el producto se enfríe antes de tocarlo.
• Seguire le istruzioni di montaggio corrette.
• Non far entrare liquidi o oggetti estranei in questo apparecchio.
• Respetar las instrucciones de montaje, y en particular los pares de apretado.
• No dejar que penetren líquidos o cuerpos extraños en el producto.
Si no se respetan estas precauciones pueden
La mancata osservanza di questa precauzione può causare gravi rischi
per l'incolumità personale o danni alle apparecchiature.
producirse graves lesiones, daños materiales.
Rev. 060816
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明