PMP4850WH [CRYDOM]
RELAY SSR PROP CNTL PNL MNT 50A;型号: | PMP4850WH |
厂家: | CRYDOM INC., |
描述: | RELAY SSR PROP CNTL PNL MNT 50A 输出元件 光电 |
文件: | 总10页 (文件大小:1063K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Control Relays
Datasheet
PMP Series
• Single Phase Proportional Controller
• Output ratings up to 90 Amps at 600 VAC
Proportional Control SSRs
• Selectable operation mode: Phase Angle or Burst Fire control
• Selectable Control Input: 0-5 VDC, 0-10 VDC, 4-20 mA
• 50/60 Hz Adaptive Operational Frequency function
• 4-20 mA input does not require an auxiliary power supply
• LED multifunction status indicator
• Contactor configuration with "Elevator" screw terminals
• cURus, IEC Rated, CE & RoHS Compliant
The PMP Series of micro-controller based Single-Phase
method to be used can be selected on the unit by means of a
selector switch located on top of the SSR.
This selector switch also allows to select the type of analog signal
to be used at the control input. The available input types are: 0- 5
VDC, 0-10 VDC, and 4-20 mA.
PMP Series Proportional SSRs are ideal for lamp dimming and
resistive heating control, among other type of applications
requiring proportional control.
Proportional Control SSRs are designed to offer precise control of
the power delivered to a resistive load in a compact 22.5mm
housing, with ratings from 25 up to 90 Amps at 90 to 600 VAC.
PMP Series solid state relays can vary the output load power
proportionally to an analog control input from 0 to 100%. This can
be achieved by two different methods: Phase Angle control and
Burst Fire control (with Distributive Zero Cross). The control
PRODUCT SELECTION
Output Voltage
90-280 VAC
345-530 VAC
420-600 VAC
25 A
PMP2425W
PMP4825W
PMP6025W
50 A
PMP2450W
PMP4850W
PMP6050W
90 A
PMP2490W
PMP4890W
PMP6090W
AVAILABLE OPTIONS
Operating Voltage
Terminal Layout
W: Contactor Configuration
(elevator screw)
24: 90-280 VAC
48: 345-530 VAC
60: 420-600 VAC
Thermal Pad
Blank: Not Included
H: Included
Series
PMP
24
25
W
P
H
Rated Load Current
Overvoltage Protection (1)
Blank: Not Included
P: Included
25: 25 Amps
50: 50 Amps
90: 90 Amps
Required for valid part number
For options only and not required for valid part number
OUTPUT VOLTAGE SPECIFICATIONS(2)
Description
Operating Voltage (45-65Hz) [VRMS]
Transient Overvoltage [Vpk] (1)
Maximum Off-State Leakage Current @ Rated Voltage [mARMS]
Minimum Off-State dV/dt @ Maximum Rated Voltage [V/μsec]
PMP24xxW
PMP48xxW
PMP60xxW
90-280
600
4
345-530
1200
2.2
420-600
1200
2
500
500
500
FDE-07-01 REV. A
Do not forget to visit us at: www.crydom.com
Copyright © 2017 Crydom Inc. Specifications subject to change without notice.
Control Relays
Datasheet
OUTPUT SPECIFICATIONS (2)
Description
Load Current, General Use UL508 @ 40°C [ARMS] (3)
Minimum Load Current [mARMS] (4)
25 A
25
100
50 A
50
100
90 A
90
150
Maximum 1 Cycle Surge Current (50/60Hz) [Apk]
Maximum On-State Voltage Drop @ Rated Current [Vrms]
Maximum 1/2 Cycle I² t for Fusing (50/60Hz) [A² sec]
Thermal Resistance Junction to Case (Rjc) [°C/W]
Maximum Power Dissipation @ Rated Current [W]
Recommended Heat Sink for Rated Current @ 40ºC [°C/W]
Minimum Power Factor (at Maximum load)
Phase Angle Control Range [%]
286/300
1.15
409/375
0.49
29
2
716/750
1.15
2563/2343
0.27
58
1
0.7
1290/1350
1.2
8320/7593
0.2
104
0.36
0.7
0.7
0 to 100
0 to 20 Cycles
0 to 100
0 to 20 Cycles
0 to 100
0 to 20 Cycles
Burst Fire Distributive Control Time Base Period
POWER SUPPLY SPECIFICATIONS (2)(5)(6)
Description
Supply Voltage Range [VDC]
Maximum Supply Current [mA]
Overvoltage Protection
Reverse Polarity Protection
PMP
8-30
30
Limited to 35 VDC for 60 sec
Yes
(2)
INPUT SPECIFICATIONS
Description
Voltage Control
Current Control
Valid Input Voltage [VDC] / Current [mA]
Maximum Allowed Input Voltage [VDC] / Current [mA]
Maximum Reverse Voltage [VDC] /Current [mA]
Pick up Voltage [VDC] / Current [mA]
Dropout Voltage [VDC] / Current [mA]
Nominal Input Impedance [Ohms]
0-10, 0-5
30
4-20
35
-35
4.3
-30
0.4
0.1
28.8k
5 Cycles
1 Cycle
4
230 @ 20 mA
5 Cycles
1 Cycle
Maximum Initialization Time [msec]
Response Time
GENERAL SPECIFICATIONS (2)
Description
Dielectric Strength, Input to Output (50/60Hz)
Dielectric Strength, Input/Output to Baseplate (50/60Hz)
Minimum Insulation Resistance (@ 500 VDC)
Maximum Capacitance, Input/Output
Ambient Operating Temperature Range (7)
Ambient Storage Temperature Range (7)
Weight (typical)
Parameters
4000 VRMS
4000 VRMS
109 Ohms
8 pF
-25 to 70 °C
-25 to 70 °C
2.6 oz (73 g)
UL94 V-0
Housing Material
Aluminum
Nickel Plating
20-25/2.2-2.8
93% non-condensing
See Status Chart
III
Baseplate Material
Hardware Finish
SSR Mounting Screw Torque Range (in-lb/Nm)
Humidity per IEC 60068-2-78
LED Input Status Indicator
Overvoltage Category
Impulse Withstand Voltage According to IEC 60664-1
Adaptative Operational Frequency Function
6 kV
Yes
Do not forget to visit us at: www.crydom.com
Copyright © 2017 Crydom Inc. Specifications subject to change without notice.
Control Relays
Datasheet
SURGE CURRENT INFORMATION
PMPxx50W
PMPxx25W
300
700
600
500
400
300
200
100
0
250
200
150
100
50
0
0.01
0.1
1
10
0.01
0.1
1
10
(sec)
(sec)
Surge Duration
Surge Duration
PMPxx90W
1400
1200
1000
800
600
400
200
0
Single Pulse (8)
0.01
0.1
1
10
(sec)
Surge Duration
POWER DISSIPATION
90 Amps
50 Amps
25 Amps
120
100
80
60
40
20
0
0
10
20
30
40
50
60
70
80
90
Load Current (Amps)
THERMAL DERATE INFORMATION(9)
PMPxx25W
PMPxx50W
PMPxx90W
2.0ºC/W
3.0ºC/W
No Heat Sink
1.0ºC/W
1.5ºC/W
2.0ºC/W
3.0ºC/W
0.36ºC/W
0.5ºC/W
1.0ºC/W
2.0ºC/W
120
100
80
60
40
20
0
70
60
50
40
30
20
10
35
30
25
20
15
10
5
0
0
25
30
35
40
45
50
55
60
65
70
25
30
35
40
45
50
55
60
65
70
25
30
35
40
45
50
55
60
65
70
Ambient Temperature (ºC)
Ambient Temperature (ºC)
Ambient Temperature (ºC)
Do not forget to visit us at: www.crydom.com
Copyright © 2017 Crydom Inc. Specifications subject to change without notice.
Control Relays
Datasheet
TRANSFER CHARACTERISTICS
Phase Angle Control, 0-5 VDC Input
Phase Angle Control, 0-10 VDC Input
Phase Angle Control, 4-20 mA Input
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
0
1
2
3
4
5
6
7
8
9
10
Input Control Voltage (Volts)
Input Control Voltage (Volts)
Input Control Current (mA)
Burst Fire Control (All Input Options)
100
90
80
70
60
50
40
30
20
10
0
0
10
20
30
40
50
60
70
80
90 100
Input Control Percent (0-5 V, 0-10 V, 4-20 mA)
INPUT CURRENT VS INPUT VOLTAGE
0-5 VDC Control Supply
0-10 VDC Control Supply
4-20 mA Control Supply
200
180
160
140
120
100
80
60
40
20
0
400
4.40
4.30
4.20
4.10
4.00
3.90
3.80
3.70
3.60
3.50
350
300
250
200
150
100
50
0
0
2
4
6
8
10
0
1
2
3
4
5
4
6
8
10
12
14
16
18
20
Input Voltage (Volts)
Input Voltage (Volts)
Input Current (mA)
EQUIVALENT CIRCUIT BLOCK DIAGRAM/WIRING DIAGRAM
A
Load
1/L1
Reference
Voltage
V
Trigger
Circuit
Controller
Current
Sensing
Voltage
Regulator
+
V
AC
0-10V (5)
+
-
0-5V
4-20mA
8-30V
+
-
B
Load
Zero
Cross
Detector
2/T1
-
Do not forget to visit us at: www.crydom.com
Copyright © 2017 Crydom Inc. Specifications subject to change without notice.
Control Relays
Datasheet
INSTALLATION INSTRUCTIONS
■
Mounting on Heat Sink
♦ Select adequate heat sink (see thermal derating curves).
♦ Be sure to use a thermal pad or thermal compound (0.006-0.008 in layer thickness recommended) SSR and the selected heat sink.
♦ SSR housing mounting holes have a diameter of 0.341in (8.66mm). Two screws are needed to mount the SSR onto a heat sink (See Fig 1). Mounting screws
are sold separately as HK8 and are suitable for all Crydom heat sinks. Otherwise, recommended screw size is 8-32 (socket) using an allen wrench (9/64 in) for the
installation. Choose screw length considering mounting surface hole depth and SSR baseplate thickness of 0.125 in (3.2 mm).
♦ Before applying full torque tighten down both screws until they contact the baseplate. Then, tighten them to 20 in-lb (2.2 Nm) min.
♦ For optimal thermal performance heat sink fins should be oriented vertically to promote natural convection airflow.
■
Mounting on Panel
♦ Locate the panel section on which the SSR will be mounted. Panel mount surface must provide adequate heat sinking capability,
uncoated, clean, flat (0.004 in/in recommended) and preferably aluminum.
THERM
P
AL
AD
♦ Be sure to use a thermal pad or thermal compound (0.006-0.008 in layer thickness recommended) between the SSR and the panel.
♦ SSR housing mounting slots have a diameter of 0.341 in (8.66 mm). Two screws are needed (not included) to mount the SSR onto a panel.
Mounting screws are sold separately as HK8. Otherwise, recommended screw size is 8-32 (socket) using allen wrench (9/64 in) forthe
installation. Choose screw length considering the mounting surface and that the SSR baseplate thickness is 0.125 in (3.2 mm).
♦ Before applying full torque tighten down both screws until they contact the baseplate. Then, tighten them to 20 in-lb (2.2 Nm) min.
■
■
Wire input and output as shown in the Wiring Diagram. For recommended wire sizes and terminal torques see TABLE 1
Select operation mode using the parameter selector switch See TABLE 2
TABLE 1. Recommended Torque and Wire Sizes
Max. Screw Torque
[in-lb (Nm)]
Wire Size
Wire Pull-Out
Terminal
Output
(Solid / Stranded)
Strength (lb)[N]
2
2 x 20 AWG (0.75 mm ) [minimum]
25 [111]
80 [355]
90 [400]
2.2 [9.8]
22 [98]
2
18-20 (2.0-2.2)
5 (0.5)
2 x 10 AWG (6 mm )
2
2 x 8 AWG (10 mm ) [maximum]
2
28 AWG (0.09 mm ) [minimum]
Input
2
12 AWG (3.3 mm ) [maximum]
TABLE 2. Operation Mode
Parameter
Selector Switch
Mode
Function
A
B
C
D
E
Phase Angle, 0-5 VDC control
Phase Angle, 0-10 VDC control
Phase Angle, 4-20 mA control
Burst Fire, 0-5 VDC control
Burst Fire, 0-10 VDC control
Burst Fire, 4-20 mA control
C
D
B
E
F
A
MODE
F
Do not forget to visit us at: www.crydom.com
Copyright © 2017 Crydom Inc. Specifications subject to change without notice.
Control Relays
Datasheet
STATUS CHARTS
TABLE 3. LED Status
Status
LED Indicator
SSR Output
OFF
No Mains Voltage (10)
Flashes twice intermittenly
Frequency Out of Range Flashes three times intermittenly
OFF
Error on Selector
Overtemperature (11)
Phase Control
Flashes four times intermittenly
Flashes five times intermittenly
Varying brightness
OFF
OFF
ON
Burst Control
Varying pulsing rate
ON
Status Chart
Error on Selector
Operation
Condition
No Mains Voltage (10)
Frequency Out of Range
Overtemperature (11)
Phase Control
Burst Control
Input
SSR Output/
Load Current
...
...
870ms
LED Indicator
150ms 280ms
Phase Angle Control Operation Mode
AC Supply
25%
50%
75%
Fully On
* Blue parts on waveform represent the output on the load
Do not forget to visit us at: www.crydom.com
Copyright © 2017 Crydom Inc. Specifications subject to change without notice.
Control Relays
Datasheet
Burst Fire Control Operation Mode
AC Supply
ꢀ.%
.±%
7.%
Fully On
* Blue parts on waveforꢃ represent the output on the load
MECHANICAL SPECIFICATIONS
1039
Tolerances: ±±0±ꢀ ꢁn ꢂ ±0. ꢃꢃ
[3.04]
All dꢁꢃensꢁons are ꢁn: ꢁnches [ꢃꢁllꢁꢃeters]
306ꢀ
[9109]
ꢀ08.
[7ꢀ03]
1088
[4708]
±089
[ꢀꢀ0.]
1018
[3±01]
ꢀ0±9
[.301]
Do not forget to visit us at: www.crydom.com
Copyright © 2017 Crydom Inc. Specifications subject to change without notice.
Control Relays
Datasheet
ACCESSORIES
Recommended Accessories
Hardware
Kit
Heat Sink
Part No.
Thermal Resistance Thermal Pad
[ºC/W]
Lug Terminal
TRM0
TRM6
HK8
HSP-7
HS259DR
2.5
0.7
HS073
HS072
HS053
HS033
HS023
0.7
0.5
0.36
0.25
AGENCY APPROVALS, CONFORMANCES AND EMC
Approvals
E116950
Conformances
United States Standard for Industrial Control Equipment - UL 508 and
Canadian Standard Association for Industrial Control Equipment – C22.2 No. 14.
IEC 60068-2-6: Amplitude Range 10-55 Hz, Displacement 0.75 mm
IEC 60068-2-27: Peak Acceleration 15g, Duration 11ms.
Vibration Resistance
Shock Resistance
Electromagnetic Compatibility
Generic
Standard
Immunity Tests
Test Specification Level
Performance
Electrostatic Discharge
IEC 61000-4-2
8kV air discharge
Criterion A
Criterion A
6kV contact discharge
Fast transients (burst)
IEC 61000-4-4
Output
Input
2kV, 5kHz, 100kHz Criterion B
1kV, 5kHz, 100kHz Criterion B
IEC 61000-6-2
Immunity for
Industrial
Surge
1kV Line to Line
2kV Line to Earth Criterion B
Criterion A
500 VDC +/-
Criterion B
Environments
Output
IEC 61000-4-5
Input Power Supply
GENERAL NOTES
(1) “P” option output will self-trigger between 450-600Vpk (for Operating Voltage option 24) or 900-1200Vpk (for Operating Voltage options 48 and 60). Not suitable for
capacitive loads.
(2) All parameters at 25°C unless otherwise specified.
(3) Heat sinking required, see derating curves. For load currents greater than 50A use conductors with at least 75°C insulation.
(4) If load current is lower than SSR minimum current, connect resistor in parallel to the load to increase current.
(5) Not required for Current control.
(6) Input should be supplied by Class 2 or double insulated power supply.
(7) No freezing or condensation allowed.
(8) For single surge pulse Tc=25°C; Tj=125°C. For AC Output SSRs, AC RMS value of surge current equals the peak value divided by √2 (1.414).
(9) UL approved rating is the one that intersects at 40°C.
(10) This function is disabled when control signal is set at 100%.
(11) This condition can be caused by excessive ambient temperature, an incorrect heat sink or high input voltage. The condition will be cleared once the internal temperature
cools down below 80 °C.
Rev. 092217
ECN 20325
Do not forget to visit us at: www.crydom.com
Copyright © 2017 Crydom Inc. Specifications subject to change without notice.
Control Relays
Datasheet
DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险
HAZARD OF
ELECTRIC
SHOCK,
EXPLOSION,
OR ARC FLASH.
RIESGO DE
DESCARGA
ELECTRICA O
EXPLOSION.
RISQUE DE
GEFAHR EINES
ELEKTRISCHE
N SCHLAGES
ODER EINER
EXPLOSION.
RISCHIO DI
SCOSSA
ELETTRICA O
DELL’ESPLOSIONE.
存在电击、
爆炸或电弧
闪烁危险
DESCHARGE
ELECTRIQUE
OU EXPLOSION
•
在操作此设
备之前请先
关闭电源。
• Eteindre
toutes les
sources
d'énergie de
cet appareil
avant de
travailler
dessus de cet
appareil
• Spenga tutta
l'alimentazione
che fornisce
questa
apparecchiatura
prima di lavorare
a questa
• Desconectar
todos los
suministros de
energia a este
equipo antes
de trabajar
• Disconnect all
power before
installing or
working with
this equipment.
• Stellen Sie
jeglichen
Strom ab, der
dieses Gerät
versorgt, bevor
Sie an dem
若不遵守这些说明,
可能会导致严重的
人身伤害甚至死亡。
con este equipo.
• Verify all
connections
and replace all
covers before
turning on
Gerät Arbeiten
durchführen
apparecchiatura
• Verificar todas
las conexiones
y colocar todas
las tapas antes
de energizer
• Verificare tutti
i collegamenti
e sostituire
tutte le coperture
prima
• Vor dem
Drehen auf
Energie alle
Anschlüsse
überprüfen
und alle
• Vérifier tous
connections, et
remettre tous
couverts en
olace avant de
mettre sous
power.
el equipo.
Failure to follow
these
instructions will
result in death
or serious injury.
dell’accensione
El
Abdeckungen
ersetzen.
L'omissione di
queste istruzioni
provocherà la
morte o
incumplimiento
de estas
instrucciones
puede provocar
la muerte o
lesiones serias.
De non-suivi de
ces instructions
provoquera la
mort ou des
lésions sérieuses
sérieuses.
Unterlassung
dieser
Anweisungen
können zum
Tode oder zu
schweren
lesioni serie
Verletzungen
führen.
WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告
RISQUE DE DOMMAGE MATERIEL ET DE
SURCHAUFFE DU BOITIER
GEFAHR VON MATERIALSCHÄDEN UND
GEHÄUSEERHITZUNG
RISK OF MATERIAL DAMAGE AND HOT
ENCLOSURE
• Les panneaux latéraux du produit peuvent être
chauds. Laisser le produit refroidir avant de le
toucher.
• Respecter les consignes de montage, et
notamment les couples de serrage.
• Ne pas laisser pénétrer de liquide ni de corps
étrangers à l'intérieur du produit.
• Die Seitenwände können heiß sein. Lassen Sie
das Produkt abkühlen, bevor Sie es berühren.
• Beachten Sie die Montageanweisungen,
• Führen Sie keine Flüssigkeiten oder
• The product's side panels may be hot, allow
the product to cool before touching.
• Follow proper mounting instructions including
torque values.
• Do not allow liquids or foreign objects to enter
this product.
Fremdkörper in das Produkt ein.
Le non-respect de cette directive peut entraîner,
des lésions corporelles graves ou des
dommages matériels.
Die Nichtbeachtung dieser Anweisung kann
Körperverletzung oder Materialschäden
zur Folge haben.
Failure to follow these instructions can result in
serious injury, or equipment damage.
RIESGO DE DAÑOS MATERIALES Y DE
SOBRECALENTAMIENTO DE LA UNIDAD
材料损坏和高温外壳的危险性
RISCHIO DI DANNI MATERIALI E D'INVOLUCRO
CALDO
• 产品的一侧面板可能很热,在其冷却前请
不要触碰。
• 遵照正确的安装说明,包括扭矩值。
• 请勿让液体及其他异物进入本产品。
• Los paneles laterales del producto pueden
estar calientes. Esperar que el producto se
enfríe antes de tocarlo.
• Respetar las instrucciones de montaje, y en
particular los pares de apretado.
• I pannelli laterali dell'apparecchio possono
scottare; lasciar quindi raffreddare il prodotto
prima di toccarlo.
• Seguire le istruzioni di montaggio corrette.
• Non far entrare liquidi o oggetti estranei in questo
apparecchio.
• No dejar que penetren líquidos o cuerpos
extraños en el producto.
La mancata osservanza di questa precauzione può
causare gravi rischi per l'incolumità personale o
danni alle apparecchiature.
如不能正确执行这些操作说明,
极有可能造成严重人体伤害或者设备的损坏。
Si no se respetan estas precauciones pueden
producirse graves lesiones, daños materiales.
Do not forget to visit us at: www.crydom.com
Copyright © 2017 Crydom Inc. Specifications subject to change without notice.
Control Relays
Datasheet
ANNEX - ENVIROMENTAL INFORMATION
The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China
Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.
Part
Name
Toxic or hazardous Substance and Elements
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
Chromium
(Cr (VI))
Polybrominated
biphenyls
(PBB)
Polybrominated
diphenyl ethers
(PBDE)
Semiconductor die
Solder
附件 - 环保信息
此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006,
电子信息产品污染控制标识要求。
部件
名称
有毒有害物质或元素
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr (VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
半导体芯片
焊接点
50
Do not forget to visit us at: www.crydom.com
Copyright © 2017 Crydom Inc. Specifications subject to change without notice.
相关型号:
©2020 ICPDF网 联系我们和版权申明