M2913-175.00M [CTS]
Oscillator,;型号: | M2913-175.00M |
厂家: | CTS |
描述: | Oscillator, |
文件: | 总3页 (文件大小:138K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
FULL SIZE D.I.L.
M package
M2911 thru M2913
VOLTAGE CONTROLLED
CRYSTAL OSCILLATORS
DOUBLE WIDE D.I.L.
W package
W2911 thru W2913
W2971 thru W2973
ECLPS 5V PECL with Extremely Low Jitter
Complementary Output
Thru-Hole
Description
Commercial: 0º to 70ºC
15 MHz to 175 MHz
These ECLPS VCXOs feature super-low
jitter of 20 ps peak-to-peak — within the
bandwidth of 12 KHz to 20 MHz the jitter
will not exceed 1 ps RMS. They are
based on the same logic as our M2910s
fixed frequency oscillators, and therefore
exhibit identical waveform characteristics.
These thru-hole VCXOs are designed for
compatibility with digital and communica-
tions systems based on the ECLPS
These VCXOs provide complementary PECL outputs thru 175 MHz
with extremely fast rise and fall times. Each oscillator is computer
tuned and computer tested to guarantee stability and frequency
pull at 0º, 25º and 70ºC. All oscillators will capture the rated pull
at all operating temperatures.
FEATURES
family of high speed PECL logic.
• Jitter less than 1 ps RMS from 12 KHz to 20 MHz
• Super low jitter of 20 ps peak to peak maximum limits loss of data packets in digital data recovery
• Will drive standard interface chips in complementary PECL.
• Duty Cycle is typically 48/52
Users have a choice of the three most
widely used combinations of pull, control
voltage and center frequency deviation.
The oscillators are available at frequencies
from 15 to 175 MHz. Standard frequency
stability is ±20 ppm.
• Three frequency deviation choices
• Output is PECL with typical rise and fall times of 225 ps
• Exceptional linearity with Deviation Sensitivity Ratio not exceeding 2.0
• Package is choice of double DIL, standard DIL with 7 pins (M1)
All models have dual complementary
outputs. All feature 250 ps typical rise/fall
times and provide superior jitter. Their low
output impedance and dual complemen-
tary outputs preserve waveform symmetry
when sending the timing waveforms over
appreciable distance. Output symmetry of
45/55 is standard.
TYPICAL APPLICATIONS
• Used in Sonet ST33 interface for generation of the transmitter data clock
SPECIAL APPLICATION NOTES
All outputs must be loaded with 270 ohms to ground, or 50 ohms to +3V
•
Outputs will drive all PECL families when they are operated in PECL configurations
•
0.98 max
(24.89)
Designed originally for advanced SONET
applications, their combination of advanced
characteristics provides special appeal to
designers of highly evolved phase-locked-
loop circuits. They provide tight control of
the voltage-to-frequency (∆F/∆V) transfer
function and feature jitter specifications of
less than 20 pico-seconds peak-to-peak.
Typical RMS jitter is 2.048 ps RMS.
0.80 max
(20.32)
DOT
DENOTES
PIN 1
Square corner indicates Pin
1
0.275 max
(6.99)
.20 MAX
.20 MIN.
.100 typ
0.20/0.30
(.50/.76)
(.025)
0.700 ±.005
(17.78 ±.13)
.018 – .001
100 TYP (NON
ACCUMULATIVE)
0.20.24
(0.51/.61
Pin 1
Centrally Located
These VCXOs are hermetically sealed in
full size (H) or wide (W) DIL packages.
Models W2911 through W2913 accept
control voltage input on pin 1, while
Models W2971 through W2973 accept
control voltage on pin 6. All models are
tested and guaranteed over full 0°C to
70°C temperature.
Pin 1
.016/.019 Dia
(.41/.48), 16 pins
2
5
7
8
.300 – .005
8
.500 – .005
150
0.600 ±.005
Centrally Located
14
9
9
16
.300
– .005
44 MAX
Glass Insulators (3)
.800 – .005
“M-1” Package
“W1” Package
ELECTRONICS
10 Commerce Dr
• New Rochelle NY 10801
+
International Sales: 1.914-712-2200 • USA Sales: +1.800.331.1236 • Fax: 914.712.2290 • www.mfelectronics.com • email:sales@mfelectronics.com
1 of 3
FULL SIZE D.I.L.
M package
M2911 thru M2913
VOLTAGE CONTROLLED
CRYSTAL OSCILLATORS
ECLPS 5V PECL with Extremely Low Jitter
Complementary Output
Thru-Hole
DOUBLE WIDE D.I.L.
W package
W2911 thru W2913
W2971 thru W2973
Commercial: 0º TO 70ºC
15 MHz to 175 MHz
ENVIRONMENTAL SPECIFICATIONS
ONE DIL WIDE, M1 Package
Temperature
Operating
Storage
Control
Voltage
for Nominal
Frequency
Stability
@
Frequency Deviation
0º to 70°C
-55º to +125°C
0.5 volts
4.5 volts
Model (Center) Freq.
Center
Temperature Cycle – Not to exceed ±5 ppm change when exposed to 2
hours maximum at each temperature from 0 to 120°C, with 25°C reference
M2911
-50 to -100 ppm
-75 to -150 ppm
50 to 100 ppm
75 to 150 ppm
M2912
M2913
2.5 volts
±20 ppm
Shock – 1000 Gs, 0.35 ms, 1/2 sine wave, 3 shocks in each plane
Vibration – 10-2000 Hz of .06" d.a. or 20 Gs, whichever is less
Humidity – Resistant to 85° R.H. at 85°C
-100 to -200 ppm 100 to 200 ppm
DOUBLE DIL WIDE, W1 Package
Voltage Voltage
Control Control
Control
Voltage
for Nominal
Frequency
Stability
@
MECHANICAL SPECIFICATIONS
Frequency Deviation
Shock – 1000 Gs, 0.35 ms. 1/2 sine wave, 3 shocks in each plane
Vibration – 10-2000 Hz of .06” d.a. or 20 Gs, whichever is less
Humidity – Resistant to 85% RH at 85°C
on
on
0.5 volts
4.5 volts
Pin 1
Pin 6 (Center) Freq.
Center
W2911 W2971
W2912 W2972
W2913 W2973
-50 to -100 ppm
-75 to -150 ppm
50 to 100 ppm
75 to 150 ppm
2.5 volts
±20 ppm
Leak – MIL STD 883, Method 1014, condition A1
Pins – Kovar, with 7 microinch gold over nickel
Bend Test – Will withstand two bends of 90° from reference
Header – Steel with gold over nickel
-100 to -200 ppm 100 to 200 ppm
ELECTRICAL SPECIFICATIONS
Frequency Range 15 MHz to 175 MHz
Case – Stainless steel, type 304
Marking – Resistant to 85% RH at 85°C
Frequency Stability Includes calibration at 25°C, operating temperature,
change of input voltage, change of load, shock and
vibration.
Resistance to Solvents – MIL STD 202, Method 215
MIN
TYP
MAX
UNITS
Input Voltage, VDD
4.5
5.0
5.5
volts
Input Current, including load
current of both ouputs
at 4.5V
at 5.0V
at 5.5V
60
68
76
ma
ma
ma
CONNECTIONS
Pin Used For
Pin Used For
All single
DIL models
1
2
5
7
Control Voltage Input, V
8
9
Output 1
Output 2 (Complement)
Output Levels (PECL),
at 5.0 VDD
“0” Level,
c
Not Used
Not Used
Ground, V
14 +5V, VDD
3.2
4.1
3.37
volts
volts
SS
“1” Level,
4.02
W2911-
W2913
1
2
3
4
5
6
7
8
Control Voltage Input
Not Used
Not Used
Not Used
Not Used
9
Output 1
Symmetry
differential
10 Output 2
11 Not used
12 Not used
13 Not used
14 Not used
15 Not used
16 +5V, VDD
48/52
1000
45/55
Input Impedance
50
10
0
Kohms
KHz
Control Voltage Bandw idth
20
Not Used
Not Used
Control Voltage, V
c
Jitter,
with Tektronix 11801B &
SD22 Head in jitter color mode
0.5 to 4.5
15
Volts, DC
Ground, V
SS
W2971-
W2973
1
2
3
4
5
6
7
8
Not Used
Not Used
Not Used
Not Used
Not Used
9
Output 1
15
20
1
ps, Pk-Pk
ps RMS
%
10 Output 2
11 Not used
12 Not used
13 Not used
14 Not used
15 Not used
16 +5V, VDD
with Agilent Phase Noise System
E5500, from 12 KHz to 20 MHz
Linearity
best straight line, percent of total
deviation sensitivity ratio
Control Voltage Input, V
c
5
10
2
Not Used
Ground, V
SS
Rise Time (20 to 80%)
Fall Time (20 to 80%)
100
100
225
225
350
350
ps
ps
ELECTRONICS
10 Commerce Dr
• New Rochelle NY 10801
+
International Sales: 1.914-712-2200 • USA Sales: +1.800.331.1236 • Fax: 914.712.2290 • www.mfelectronics.com • email:sales@mfelectronics.com
2 of 3
FULL SIZE D.I.L.
M package
M2911 thru M2913
VOLTAGE CONTROLLED
CRYSTAL OSCILLATORS
ECLPS 5V PECL with Extremely Low Jitter
Complementary Output
Thru-Hole
DOUBLE WIDE D.I.L.
W package
W2911 thru W2913
W2971 thru W2973
Commercial: 0º TO 70ºC
15 MHz to 175 MHz
Waveforms taken on TEK 11801B with SD-22 Head
Fig. 1: 155.52 MHz PECL oscillator,
showing steep rise and fall times and
excellent duty cycle. Levels have 900 mv
difference between “1” and “0”.
Fig. 2: M2912-77.76 MHz oscillator with
expansion of transition at 3.7 volts. Jitter is
shown by the histogram of the distribution
of the waveform at 3.7 volts. The distribu-
tion is unimodal, with peak-to-peak jitter
of 16 ps peak-to-peak, and 2.27 ps RMS.
HOW TO ORDER
For Part Number, put package type before model number,
and add frequency in MHz, for example:
M 2 9 1 2- 7 7 .7 6 M
“M” is full size DIL
“W” is double wide DIL is model
type
“2912”
“77.76 M”
frequency
in MHz
Unless customer-specific terms and conditions
are signed by an officer of MF Electronics, the
sale of this and all MF Electronics products are
subject to terms and conditions set forth at
www.mfelectronics.com/terms
SS#
Rev.
A
M2911
ELECTRONICS
10 Commerce Dr
• New Rochelle NY 10801
+
International Sales: 1.914-712-2200 • USA Sales: +1.800.331.1236 • Fax: 914.712.2290 • www.mfelectronics.com • email:sales@mfelectronics.com
3 of 3
相关型号:
M29150BG-50-TN4-R
Fixed Positive LDO Regulator, 5V, 0.7V Dropout, PSSO4, HALOGEN FREE, TO-252, 5 PIN
UTC
M29150BG-50-TN5-R
Fixed Positive LDO Regulator, 5V, 0.7V Dropout, PSSO5, HALOGEN FREE, TO-252, 5 PIN
UTC
M29150BL-50-TN4-R
Fixed Positive LDO Regulator, 5V, 0.7V Dropout, PSSO4, LEAD FREE, TO-252, 5 PIN
UTC
M29150BL-50-TN5-R
Fixed Positive LDO Regulator, 5V, 0.7V Dropout, PSSO5, LEAD FREE, TO-252, 5 PIN
UTC
©2020 ICPDF网 联系我们和版权申明