CY7C1049GN30-10VXIT [CYPRESS]
Standard SRAM, 512KX8, 10ns, CMOS, PDSO36, SOJ-36;型号: | CY7C1049GN30-10VXIT |
厂家: | CYPRESS |
描述: | Standard SRAM, 512KX8, 10ns, CMOS, PDSO36, SOJ-36 静态存储器 光电二极管 内存集成电路 |
文件: | 总17页 (文件大小:384K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CY7C1049GN
4-Mbit (512K words × 8-bit) Static RAM
4-Mbit (512K words
× 8-bit) Static RAM
Features
Functional Description
■ High speed
❐ tAA = 10 ns
CY7C1049GN is a high-performance CMOS fast static RAM
device organized as 512K words by 8-bits.
Data writes are performed by asserting the Chip Enable (CE) and
Write Enable (WE) inputs LOW, while providing the data on I/O0
through I/O7 and address on A0 through A18 pins.
■ Low active and standby currents
❐ Active current: ICC = 38 mA typical
❐ Standby current: ISB2 = 6 mA typical
Data reads are performed by asserting the Chip Enable (CE) and
■ Operating voltage range: 1.65 V to 2.2 V, 2.2 V to 3.6 V, and
4.5 V to 5.5 V
Output Enable (OE) inputs LOW and providing the required
address on the address lines. Read data is accessible on the I/O
lines (I/O0 through I/O7).
■ 1.0 V data retention
All I/Os (I/O0 through I/O7) are placed in a high-impedance state
during the following events:
■ TTL-compatible inputs and outputs
■ Pb-free 36-pin SOJ and 44-pin TSOP II packages
■ The device is deselected (CE HIGH)
■ The control signal OE is de-asserted
The logic block diagram is on page 2.
Product Portfolio
Power Dissipation
Speed
Operating ICC, (mA)
(ns)
Product
Range
VCC Range (V)
Standby, ISB2 (mA)
f = fmax
Typ[1]
10/15
Max
40
Typ[1]
Max
CY7C1049GN18
Industrial
1.65 V–2.2 V
2.2 V–3.6 V
4.5 V–5.5 V
15
10
10
–
6
8
CY7C1049GN30
CY7C1049GN
38
38
45
45
Note
1. Typical values are included only for reference and are not guaranteed or tested. Typical values are measured at V = 1.8 V (for a V range of 1.65 V–2.2 V),
CC
CC
V
= 3 V (for a V range of 2.2 V–3.6 V), and V = 5 V (for a V range of 4.5 V–5.5 V), T = 25 °C.
CC
CC CC CC A
Cypress Semiconductor Corporation
Document Number: 002-10613 Rev. *C
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised November 14, 2017
CY7C1049GN
Logic Block Diagram – CY7C1049GN
INPUT BUFFER
A0
A1
A2
A3
I/O0‐I/O7
512K x 8
RAM ARRAY
A4
A5
A6
A7
A8
A9
COLUMN
DECODER
WE
OE
CE
Document Number: 002-10613 Rev. *C
Page 2 of 17
CY7C1049GN
Contents
Pin Configurations ...........................................................4
Maximum Ratings .............................................................5
Operating Range ...............................................................5
DC Electrical Characteristics ..........................................5
Capacitance ......................................................................6
Thermal Resistance ..........................................................6
AC Test Loads and Waveforms .......................................6
Data Retention Characteristics .......................................7
Data Retention Waveform ................................................7
AC Switching Characteristics .........................................8
Switching Waveforms ......................................................9
Truth Table ......................................................................12
Ordering Information ......................................................13
Ordering Code Definitions .........................................13
Package Diagrams ..........................................................14
Acronyms ........................................................................15
Document Conventions .................................................15
Units of Measure .......................................................15
Document History Page .................................................16
Sales, Solutions, and Legal Information ......................17
Worldwide Sales and Design Support .......................17
Products ....................................................................17
PSoC® Solutions ......................................................17
Cypress Developer Community .................................17
Technical Support .....................................................17
Document Number: 002-10613 Rev. *C
Page 3 of 17
CY7C1049GN
Pin Configurations
Figure 1. 36-pin SOJ pinout [2]
A0
A1
1
2
3
4
5
6
7
8
9
36 NC
A18
A17
A16
A15
35
34
33
32
A2
A3
A4
CE
I/O0
I/O1
VCC
31 OE
30 I/O7
29 I/O6
28 GND
27 VCC
26 I/O5
GND 10
I/O2 11
SOJ
I/O3
WE
A5
I/O4
A14
A13
A12
A11
A10
NC
12
13
14
15
16
17
18
25
24
23
22
21
20
19
A6
A7
A8
A9
Figure 2. 44-pin TSOP II pinout, Single Chip Enable [2]
NC
NC
A0
1
2
3
4
5
6
7
8
9
44 NC
NC
43
42
41
40
NC
A1
A18
A17
A2
A3
39 A16
38 A15
37 /OE
36 I/O7
35 I/O6
34 VSS
A4
/CE
I/O0
44-pin TSOP II
I/O1 10
VCC 11
VSS
I/O2
I/O3
/WE
VCC
I/O5
I/O4
A14
12
13
14
15
33
32
31
30
A5 16
29 A13
A6
A7
A8
A9
NC
NC
A12
A11
A10
NC
17
18
19
20
21
22
28
27
26
25
24
23
NC
NC
Note
2. NC pins are not connected internally to the die.
Document Number: 002-10613 Rev. *C
Page 4 of 17
CY7C1049GN
DC input voltage [3].............................. –0.5 V to VCC + 0.5 V
Current into outputs (in LOW state) ............................ 20 mA
Maximum Ratings
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Static discharge voltage
(MIL-STD-883, Method 3015) .................................> 2001 V
Storage temperature ................................ –65 C to +150 C
Latch-up current ....................................................> 140 mA
Ambient temperature
with power applied ................................... –55 C to +125 C
Operating Range
Supply voltage
Grade
Ambient Temperature
VCC
on VCC relative to GND [3] ..................... –0.5 to VCC + 0.5 V
Industrial
–40 C to +85 C
1.65 V to 2.2 V,
2.2 V to 3.6 V,
4.5 V to 5.5 V
DC voltage applied to outputs
in HI-Z State [3] ...................................–0.5 V to VCC + 0.5 V
DC Electrical Characteristics
Over the operating range of –40 C to 85 C
10 ns/15 ns
Parameter
Description
Test Conditions
Unit
Max
Min
Typ [4]
VOH
Output HIGH
voltage
1.65 V to 2.2 V VCC = Min, IOH = –0.1 mA
1.4
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
38
–
–
–
V
2.2 V to 2.7 V
2.7 V to 3.0 V
V
CC = Min, IOH = –1.0 mA
CC = Min, IOH = –4.0 mA
2
–
V
2.2
–
3.0 V to 3.6 V VCC = Min, IOH = –4.0 mA
2.4
–
4.5 V to 5.5 V
4.5 V to 5.5 V
V
CC = Min, IOH = –4.0 mA
CC = Min, IOH = –0.1mA
2.4
VCC – 0.5[5]
–
V
–
0.2
VOL
VIH
VIL
Output LOW
voltage
1.65 V to 2.2 V VCC = Min, IOL = 0.1 mA
–
V
V
V
2.2 V to 2.7 V
2.7 V to 3.6 V
V
CC = Min, IOL = 2 mA
CC = Min, IOL = 8 mA
–
0.4
V
–
0.4
4.5 V to 5.5 V VCC = Min, IOL = 8 mA
1.65 V to 2.2 V –
–
0.4
VCC + 0.2[3]
V
CC + 0.3[3]
VCC + 0.3[3]
1.4
2.2 V to 2.7 V
2.7 V to 3.6 V
4.5 V to 5.5 V
–
–
–
2
Input HIGH
voltage
2
2
VCC + 0.5[3]
1.65 V to 2.2 V –
–0.2[3]
–0.3[3]
–0.3[3]
–0.5[3]
–1
0.4
0.6
0.8
0.8
+1
+1
45
2.2 V to 2.7 V
2.7 V to 3.6 V
4.5 V to 5.5 V
–
Input LOW
voltage
–
–
IIX
Input leakage current
Output leakage current
Operating supply current
GND < VIN < VCC
A
A
IOZ
ICC
GND < VOUT < VCC, Output disabled
–1
Max VCC, IOUT = 0 mA, f = 100 MHz
CMOS levels
f = 66.7 MHz
–
mA
–
40
ISB1
ISB2
Notes
Automatic CE power-down
current – TTL inputs
Max VCC, CE > VIH,
–
15
mA
mA
VIN > VIH or VIN < VIL, f = fMAX
Automatic CE power-down
current – CMOS inputs
Max VCC, CE > VCC – 0.2 V,
VIN > VCC – 0.2 V or VIN < 0.2 V, f = 0
–
6
8
3. VIL(min) = –2.0 V and VIH(max) = VCC + 2 V for pulse durations of less than 20 ns.
4. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at VCC = 1.8 V (for VCC range of 1.65 V – 2.2 V),
CC = 3 V (for VCC range of 2.2V – 3.6 V), and VCC = 5 V (for VCC range of 4.5 V – 5.5 V), TA = 25 °C.
V
5. This parameter is guaranteed by design and not tested.
Document Number: 002-10613 Rev. *C
Page 5 of 17
CY7C1049GN
Capacitance
Parameter [6]
Description
Input capacitance
I/O capacitance
Test Conditions
TA = 25 C, f = 1 MHz,
VCC = VCC(typ)
36-pin SOJ 44-pin TSOP II Unit
CIN
10
10
10
10
pF
pF
COUT
Thermal Resistance
Parameter [6]
Description
Test Conditions
36-pin SOJ 44-pin TSOP II Unit
JA
Thermal resistance
(junction to ambient)
Still air, soldered on a 3 × 4.5 inch,
four-layer printed circuit board
59.52
68.85
C/W
JC
Thermal resistance
(junction to case)
31.48
15.97
C/W
AC Test Loads and Waveforms
Figure 3. AC Test Loads and Waveforms [7]
High-Z Characteristics:
R1
50
VCC
Output
VTH
Output
R2
Z = 50
30 pF*
0
5 pF*
* Including
jig and
scope
(a)
(b)
* Capacitive load consists
of all components of the
test environment
All Input Pulses
V
HIGH
90%
10%
90%
10%
GND
Fall Time:
> 1 V/ns
Rise Time:
> 1 V/ns
(c)
Parameters
R1
1.8 V
1667
1538
0.9
3.0 V
317
351
1.5
3
5.0 V
Unit
317
351
1.5
3
R2
VTH
V
VHIGH
1.8
V
Notes
6. Tested initially and after any design or process changes that may affect these parameters.
7. Full-device AC operation assumes a 100-µs ramp time from 0 to VCC(min) and a 100-µs wait time after VCC stabilization.
Document Number: 002-10613 Rev. *C
Page 6 of 17
CY7C1049GN
Data Retention Characteristics
Over the operating range of –40 C to 85 C
Parameter
VDR
ICCDR
Description
VCC for data retention
Data retention current
Conditions
Min
1
Max
–
Unit
V
VCC = 1.2 V, CE > VCC – 0.2 V[8]
IN > VCC – 0.2 V, or VIN < 0.2 V
,
–
8
mA
V
[9]
tCDR
Chip deselect to data retention
time
0
–
ns
[8, 9]
tR
Operation recovery time
VCC > 2.2 V
VCC < 2.2 V
10
15
–
–
ns
ns
Data Retention Waveform
Figure 4. Data Retention Waveform [8]
DATA RETENTION MODE
VDR = 1.0 V
VCC
VCC(min)
tCDR
VCC(min)
tR
CE
Notes
8. Full-device operation requires linear VCC ramp from VDR to VCC(min) > 100 s or stable at VCC (min) > 100 s.
9. These parameters are guaranteed by design.
Document Number: 002-10613 Rev. *C
Page 7 of 17
CY7C1049GN
AC Switching Characteristics
Over the operating range of –40 C to 85 C
10 ns
15 ns
Unit
Parameter [10]
Description
Min
Max
Min
Max
Read Cycle
tRC
Read cycle time
10
–
3
–
–
0
–
3
–
0
–
–
10
–
15
–
3
–
–
0
–
3
–
0
–
–
15
–
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tAA
Address to data
tOHA
Data hold from address change
CE LOW to data
tACE
10
4.5
–
15
8
tDOE
OE LOW to data
tLZOE
tHZOE
tLZCE
tHZCE
tPU
OE LOW to low impedance [11]
OE HIGH to High-Z [11]
CE LOW to low impedance [11]
CE HIGH to High-Z [11]
CE LOW to power-up [12, 13]
CE HIGH to power-down [12, 13]
–
5
8
–
–
5
8
–
–
tPD
10
15
Write Cycle [13, 14]
tWC Write cycle time
tSCE
tAW
10
7
7
0
0
7
5
0
3
–
–
–
–
–
–
–
–
–
–
5
15
12
12
0
–
–
–
–
–
–
–
–
–
8
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
CE LOW to write end
Address setup to write end
Address hold from write end
Address setup to write start
WE pulse width
tHA
tSA
0
tPWE
tSD
12
8
Data setup to write end
Data hold from write end
WE HIGH to low impedance [11]
WE LOW to High-Z [11]
tHD
0
tLZWE
tHZWE
3
–
Notes
10. Test conditions assume a signal transition time (rise/fall) of 3 ns or less, timing reference levels of 1.5 V (for VCC > 3 V) and VCC/2 (for VCC < 3 V), and input pulse
levels of 0 to 3 V (for VCC > 3 V) and 0 to VCC (for VCC < 3 V).Testconditionsforthereadcycleuseoutputloading, asshowninpart(a)ofFigure 3 on page 6, unlessspecifiedotherwise.
11. tHZOE, tHZCE, tHZWE, tLZOE, tLZCE, and tLZWE are specified with a load capacitance of 5 pF, as shown in part (b) of Figure 3 on page 6. Transition is measured 200 mV from steady state
voltage.
12. These parameters are guaranteed by design and are not tested.
13. The internal write time of the memory is defined by the overlap of WE = VIL, CE = VIL. These signals must be LOW to initiate a write, and the HIGH transition of any
of these signals can terminate the operation. The input data setup and hold timing should be referenced to the edge of the signal that terminates the write.
14. The minimum write cycle pulse width in Write Cycle No. 2 (WE Controlled, OE LOW) should be equal to sum of tDS and tHZWE
.
Document Number: 002-10613 Rev. *C
Page 8 of 17
CY7C1049GN
Switching Waveforms
Figure 5. Read Cycle No. 1 (Address Transition Controlled) [15, 16]
tRC
ADDRESS
tAA
tOHA
PREVIOUS DATAOUT
VALID
DATA I/O
DATAOUT VALID
Figure 6. Read Cycle No. 2 (OE Controlled) [15, 16]
ADDRESS
tRC
CE
tPD
tHZCE
tACE
OE
tHZOE
tDOE
tLZOE
HIGH
IMPEDANCE
HIGH IMPEDANCE
tLZCE
tPU
DATA I/O
DATAOUT VALID
VCC
SUPPLY
CURRENT
ISB
Notes
15. WE is HIGH for the read cycle.
16. Address valid prior to or coincident with CE LOW transition.
Document Number: 002-10613 Rev. *C
Page 9 of 17
CY7C1049GN
Switching Waveforms (continued)
Figure 7. Write Cycle No. 1 (CE Controlled) [17, 18]
tW
C
A D D R E S S
tS A
t S C
E
C E
tA W
tH
A
t P W
E
W E
O E
t H
tH D
Z O
E
tS D
D A T A I / O
D A T AIN V A L ID
Figure 8. Write Cycle No. 2 (WE Controlled, OE LOW) [17, 18, 19]
tW C
ADDRESS
tSCE
CE
tAW
tHA
tSA
tPW E
W E
tLZW E
t
tSD
HZW E
tHD
VALID
DATA I /O
DATA
IN
Notes
17. The internal write time of the memory is defined by the overlap of WE = VIL, CE = VIL. These signals must be LOW to initiate a write, and the HIGH transition of any
of these signals can terminate the operation. The input data setup and hold timing should be referenced to the edge of the signal that terminates the write.
18. Data I/O is in HI-Z state if CE = VIH, or OE = VIH.
19. The minimum write cycle pulse width should be equal to sum of tSD and tHZWE
.
Document Number: 002-10613 Rev. *C
Page 10 of 17
CY7C1049GN
Switching Waveforms (continued)
Figure 9. Write Cycle No. 3 (WE Controlled) [20, 21, 22]
tWC
ADDRESS
CE1
tSCE
CE2
tAW
tHA
tSA
tPWE
WE
OE
tHD
tSD
NOTE 23
DATA I/O
DATA IN VALID
tHZOE
Notes
20. The internal write time of the memory is defined by the overlap of WE = VIL, CE = VIL. These signals must be LOW to initiate a write, and the HIGH transition of any
of these signals can terminate the operation. The input data setup and hold timing should be referenced to the edge of the signal that terminates the write.
21. Data I/O is in HI-Z state if CE = VIH, or OE = VIH.
22. Data I/O is high impedance if OE = VIH
.
23. During this period the I/Os are in output state. Do not apply input signals.
Document Number: 002-10613 Rev. *C
Page 11 of 17
CY7C1049GN
Truth Table
CE
H
L
OE
X[24]
L
WE
X[24]
H
I/O0–I/O7
HI-Z
Mode
Power
Power down
Read all bits
Write all bits
Standby (ISB)
Data out
Data in
HI-Z
Active (ICC
Active (ICC
Active (ICC
)
)
)
L
X
L
L
H
H
Selected, outputs disabled
Note
24. The input voltage levels on these pins should be either at VIH or VIL.
Document Number: 002-10613 Rev. *C
Page 12 of 17
CY7C1049GN
Ordering Information
Speed
(ns)
Voltage
Range
Package
Diagram
Operating
Range
Ordering Code
Package Type (all Pb-free)
10
2.2 V–3.6 V CY7C1049GN30-10ZSXI
CY7C1049GN30-10ZSXIT
CY7C1049GN30-10VXI
51-85087 44-pin TSOP II
Industrial
51-85087 44-pin TSOP II, Tape and Reel
51-85090 36-pin Molded SOJ
CY7C1049GN30-10VXIT
51-85090 36-pin Molded SOJ, Tape and Reel
51-85090 36-pin Molded SOJ
4.5 V–5.5 V CY7C1049GN-10VXI
CY7C1049GN-10VXIT
51-85090 36-pin Molded SOJ, Tape and Reel
Ordering Code Definitions
CY 7 1 04 9 GN XX
-
XX
C
XX
I
X
X
X = blank or T
blank = Bulk; T = Tape and Reel
Temperature Range: I = Industrial
Pb-free
Package Type: XX = ZS or V
ZS = 44-pin TSOP II; V= 36-pin Molded SOJ
Speed: XX = 10 ns
Voltage Range: XX = 30 or blank
30 = 2.2 V–3.6 V; no character = 4.5 V–5.5 V
Process Technology: GN = 65 nm
Data Width: 9 = × 8-bits
Density: 04 = 4-Mbit
Family Code: 1 = Fast Asynchronous SRAM family
Technology Code: C = CMOS
Marketing Code: 7 = SRAM
Company ID: CY = Cypress
Document Number: 002-10613 Rev. *C
Page 13 of 17
CY7C1049GN
Package Diagrams
Figure 10. 44-pin TSOP Z44-II Package Outline, 51-85087
51-85087 *E
Figure 11. 36-pin SOJ V36.4 (Molded) Package Outline, 51-85090
51-85090 *G
Document Number: 002-10613 Rev. *C
Page 14 of 17
CY7C1049GN
Acronyms
Document Conventions
Units of Measure
Acronym
Description
BHE
BLE
byte high enable
Symbol
°C
Unit of Measure
byte low enable
chip enable
Degrees Celsius
megahertz
microamperes
microseconds
milliamperes
millimeter
nanoseconds
ohms
MHz
A
s
CE
CMOS
I/O
complementary metal oxide semiconductor
input/output
mA
mm
ns
OE
output enable
SRAM
TSOP
TTL
static random access memory
thin small outline package
transistor-transistor logic
very fine-pitch ball grid array
write enable
%
percent
VFBGA
WE
pF
V
picofarads
volts
W
watts
Document Number: 002-10613 Rev. *C
Page 15 of 17
CY7C1049GN
Document History Page
Document Title: CY7C1049GN, 4-Mbit (512K words × 8-bit) Static RAM
Document Number: 002-10613
Orig. of
Change
Submission
Date
Rev.
ECN No.
Description of Change
**
5074703
5082587
NILE
NILE
01/06/2016 New data sheet.
*A
01/12/2016 Updated Logic Block Diagram – CY7C1049GN.
Updated Ordering Information:
Updated part numbers.
*B
5437570
NILE
09/15/2016 Updated DC Electrical Characteristics:
Removed details of VOH parameter corresponding to “2.7 V to 3.6 V” and
Test Condition “VCC = Min, IOH = –4.0 mA”.
Added details of VOH parameter corresponding to “2.7 V to 3.0 V” and
Test Condition “VCC = Min, IOH = –4.0 mA”.
Added details of VOH parameter corresponding to “3.0 V to 3.6 V” and
Test Condition “VCC = Min, IOH = –4.0 mA”.
Changed minimum value of VIH parameter corresponding to “4.5 V to 5.5 V”
from 2.2 V to 2 V.
Updated Note 3 (Replaced “2 ns” with “20 ns”).
Updated Ordering Information:
Updated part numbers.
Updated to new template.
*C
5966829
NILE
11/14/2017 Updated Switching Waveforms:
Updated Figure 6.
Updated Figure 7.
Updated Figure 8.
Updated Figure 9.
Updated to new template.
Completing Sunset Review.
Document Number: 002-10613 Rev. *C
Page 16 of 17
CY7C1049GN
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
®
Products
PSoC Solutions
ARM® Cortex® Microcontrollers
cypress.com/arm
cypress.com/automotive
cypress.com/clocks
cypress.com/interface
cypress.com/iot
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6
Automotive
Cypress Developer Community
Clocks & Buffers
Interface
Forums | WICED IOT Forums | Projects | Video | Blogs | Training
| Components
Internet of Things
Memory
Technical Support
cypress.com/memory
cypress.com/mcu
cypress.com/support
Microcontrollers
PSoC
cypress.com/psoc
Power Management ICs
Touch Sensing
USB Controllers
Wireless Connectivity
cypress.com/pmic
cypress.com/touch
cypress.com/usb
cypress.com/wireless
© Cypress Semiconductor Corporation, 2016-2017. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document,
including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries
worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other
intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress
hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to
modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users
(either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as
provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation
of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent
permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any
product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is
the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products
are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or
systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the
device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device or system whose failure to perform can be reasonably
expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim,
damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other
liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in
the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 002-10613 Rev. *C
Revised November 14, 2017
Page 17 of 17
相关型号:
©2020 ICPDF网 联系我们和版权申明