CY7C1303BV25-133BZC [CYPRESS]
QDR SRAM, 1MX18, 3ns, CMOS, PBGA165, 13 X 15 MM, 1.40 MM HEIGHT, 1 MM PITCH, FBGA-165;型号: | CY7C1303BV25-133BZC |
厂家: | CYPRESS |
描述: | QDR SRAM, 1MX18, 3ns, CMOS, PBGA165, 13 X 15 MM, 1.40 MM HEIGHT, 1 MM PITCH, FBGA-165 时钟 静态存储器 内存集成电路 |
文件: | 总19页 (文件大小:247K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
18-Mbit Burst of 2 Pipelined SRAM with
QDR™ Architecture
Features
Functional Description
• Separate independent Read and Write data ports
— Supports concurrent transactions
• 167-MHz Clock for high bandwidth
— 2.5 ns Clock-to-Valid access time
• 2-Word Burst on all accesses
The CY7C1303BV25 and CY7C1306BV25 are 2.5V
Synchronous Pipelined SRAMs equipped with QDR™ archi-
tecture. QDR architecture consists of two separate ports to
access the memory array. The Read port has dedicated Data
Outputs to support Read operations and the Write Port has
dedicated Data inputs to support Write operations. Access to
each port is accomplished through a common address bus.
The Read address is latched on the rising edge of the K clock
and the Write address is latched on the rising edge of K clock.
QDR has separate data inputs and data outputs to completely
eliminate the need to “turn-around” the data bus required with
common I/O devices. Accesses to the CY7C1303BV25/
CY7C1306BV25 Read and Write ports are completely
independent of one another. All accesses are initiated
synchronously on the rising edge of the positive input clock
(K). In order to maximize data throughput, both Read and
Write ports are equipped with Double Data Rate (DDR) inter-
faces. Therefore, data can be transferred into the device on
every rising edge of both input clocks (K and K) and out of the
device on every rising edge of the output clock (C and C, or K
and K when in single clock mode) thereby maximizing perfor-
mance while simplifying system design. Each address location
is associated with two 18-bit words (CY7C1303BV25) or two
36-bit words (CY7C1306BV25) that burst sequentially into or
out of the device.
• Double Data Rate (DDR) interfaces on both Read and
Write Ports (data transferred at 333 MHz) @167 MHz
• Two input clocks (K and K) for precise DDR timing
— SRAM uses rising edges only
• Two output clocks (C and C) account for clock skew
and flight time mismatching
• Single multiplexed address input bus latches address
inputs for both Read and Write ports
• Separate Port Selects for depth expansion
• Synchronous internally self-timed writes
• 2.5V core power supply with HSTL Inputs and Outputs
• 13 x 15 x 1.4 mm 1.0-mm pitch fBGA package, 165 ball
(11x15 matrix) Variable drive HSTL output buffers
• Expanded HSTL output voltage (1.4V–1.9V)
• JTAG Interface
Depth expansion is accomplished with a Port Select input for
each port. Each Port Selects allow each port to operate
independently. 38-05627
• Variable Impedance HSTL
Configurations
All synchronous inputs pass through input registers controlled
by the K or K input clocks. All data outputs pass through output
registers controlled by the C or C input clocks. Writes are
conducted with on-chip synchronous self-timed write circuitry.
CY7C1303BV25 – 1M x 18
CY7C1306BV25 – 512K x 36
Cypress Semiconductor Corporation
Document #: 38-05627 Rev. **
•
3901 North First Street
•
San Jose, CA 95134
•
408-943-2600
Revised July 29, 2004
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
Logic Block Diagram (CY7C1303BV25)
D[17:0]
18
Write
Write
Data Reg
Data Reg
Address
Register
A(18:0)
Address
Register
A(18:0)
19
19
512Kx18 512Kx18
Memory
Array
Memory
Array
K
K
CLK
Gen.
RPS
Control
Logic
C
C
Read Data Reg.
36
18
Vref
18
Reg.
Reg.
Reg.
18
Control
Logic
WPS
BWS0
18
Q[17:0]
BWS1
18
Logic Block Diagram (CY7C1306BV25)
D[35:0]
36
Write
Data Reg
Write
Data Reg
Address
Register
A(17:0)
Address
Register
A(17:0)
18
18
256Kx36 256Kx36
Memory
Array
Memory
Array
K
CLK
Gen.
RPS
Control
Logic
K
C
C
Read Data Reg.
72
36
Vref
36
Reg.
Reg.
Reg.
36
Control
Logic
WPS
BWS0
36
Q[35:0]
BWS1
BWS2
36
BWS3
Selection Guide
CY7C1303BV25-167 CY7C1303BV25-133 CY7C1303BV25-100
CY7C1306BV25-167 CY7C1306BV25-133 CY7C1306BV25-100
Unit
MHz
mA
Maximum Operating Frequency
Maximum Operating Current
167
133
100
TBD
TBD
TBD
Document #: 38-05627 Rev. **
Page 2 of 19
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
Pin Configuration – CY7C1303BV25 (Top View)
1
2
3
4
5
6
7
8
9
10
11
Gnd/
Gnd/
72M
A
B
C
D
E
F
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
TDO
144M NC/ 36M
WPS
A
BWS1
NC
K
NC
BWS0
A
RPS
A
A
NC
NC
NC
NC
NC
NC
VDDQ
NC
NC
NC
NC
NC
NC
A
NC
Q8
D8
D7
Q6
Q5
D5
ZQ
D4
Q3
Q2
D2
D1
Q0
TDI
Q9
NC
D9
D10
Q10
Q11
D12
Q13
VDDQ
D14
Q14
D15
D16
Q16
Q17
A
K
NC
Q7
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VSS
A
A
A
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VSS
A
D11
NC
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
A
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
A
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
A
NC
D6
Q12
D13
VREF
NC
NC
NC
VREF
Q4
G
H
J
K
L
NC
D3
Q15
NC
NC
Q1
M
N
P
R
D17
NC
NC
D0
A
C
A
TCK
A
A
C
A
A
TMS
Pin Configuration - CY7C1306BV25 (Top View)
1
2
3
4
5
6
7
8
9
10
11
Gnd/
Gnd/
A
B
C
D
E
F
NC
Q27
D27
D28
Q29
Q30
D30
NC
288M NC/ 72M WPS
BWS2
BWS3
A
K
BWS1
BWS0
A
RPS
A
NC/36M
D17
D16
Q16
Q15
D14
Q13
VDDQ
D12
Q12
D11
D10
Q10
Q9
144M
NC
Q8
D8
D7
Q6
Q5
D5
ZQ
D4
Q3
Q2
D2
D1
Q0
TDI
Q18
Q28
D20
D29
Q21
D22
VREF
Q31
D32
Q24
Q34
D26
D35
TCK
D18
D19
Q19
Q20
D21
Q22
VDDQ
D23
Q23
D24
D25
Q25
Q26
A
A
K
Q17
Q7
VSS
A
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VSS
A
VSS
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
A
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
A
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
A
D15
D6
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
Q14
D13
VREF
Q4
G
H
J
D31
Q32
Q33
D33
D34
Q35
TDO
K
L
D3
Q11
Q1
M
N
P
R
VSS
D9
A
A
C
A
D0
A
A
C
A
A
A
TMS
Document #: 38-05627 Rev. **
Page 3 of 19
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
Pin Definitions
Name
I/O
Description
D[x:0]
Input-
Synchronous
Data input signals, sampled on the rising edge of K and K clocks during valid write
operations.
CY7C1303BV25 – D[17:0]
CY7C1306BV25 – D[35:0]
WPS
Input-
Synchronous
Write Port Select, active LOW. Sampled on the rising edge of the K clock. When
asserted active, a Write operation is initiated. Deasserting will deselect the Write port.
Deselecting the Write port will cause D[x:0] to be ignored.
BWS0, BWS1,
BWS2, BWS3
Input-
Synchronous
Byte Write Select 0, 1, 2 and 3 - active LOW. Sampled on the rising edge of the K and
K clocks during Write operations. Used to select which byte is written into the device
during the current portion of the Write operations.
CY7C1303BV25 - BWS0 controls D[8:0] and BWS1 controls D[17:9].
CY7C1306BV25 - BWS0 controls D[8:0], BWS1 controls D[17:9], BWS2 controls D[26:18]
and BWS3 controls D[35:27]
Bytes not written remain unaltered. Deselecting a Byte Write Select will cause the corre-
sponding byte of data to be ignored and not written into the device.
A
Input-
Synchronous
Address Inputs. Sampled on the rising edge of the K clock during active Read opera-
tions and on the rising edge of K for Write operations. These address inputs are multi-
plexed for both Read and Write operations. Internally, the device is organized as 1M x
18 (2 arrays each of 512K x 18) for CY7C1303BV25 and 512K x 36 (2 arrays each of
256K x 36) for CY7C1306BV25. Therefore, only 19 address inputs are needed to access
the entire memory array of CY7C1303BV25 and 18 address inputs for CY7C1306BV25.
These inputs are ignored when the appropriate port is deselected.
Q[x:0]
Outputs-
Synchronous
Data Output signals. These pins drive out the requested data during a Read operation.
Valid data is driven out on the rising edge of both the C and C clocks during Read
operations or K and K when in single clock mode. When the Read port is deselected,
Q
[x:0] are automatically three-stated.
CY7C1303BV25 - Q[17:0]
CY7C1306BV25 - Q[35:0]
RPS
Input-
Synchronous
Read Port Select, active LOW. Sampled on the rising edge of positive input clock (K).
When active, a Read operation is initiated. Deasserting will cause the Read port to be
deselected. When deselected, the pending access is allowed to complete and the output
drivers are automatically three-stated following the next rising edge of the K clock. Each
read access consists of a burst of two sequential 18-bit or 36-bit transfers.
C
C
K
Input-Clock
Input-Clock
Input-Clock
Positive Output Clock Input. C is used in conjunction with C to clock out the Read data
from the device. C and C can be used together to deskew the flight times of various
devices on the board back to the controller. See application example for further details.
Negative Output Clock Input. C is used in conjunction with C to clock out the Read
data from the device. C and C can be used together to deskew the flight times of various
devices on the board back to the controller. See application example for further details.
Positive Input Clock Input. The rising edge of K is used to capture synchronous inputs
to the device and to drive out data through Q[x:0] when in single clock mode. All accesses
are initiated on the rising edge of K.
K
Input-Clock
Input
Negative Input Clock Input. K is used to capture synchronous inputs to the device and
to drive out data through Q[x:0] when in single clock mode.
ZQ
Output Impedance Matching Input. This input is used to tune the device outputs to the
system data bus impedance. Q[x:0] output impedance are set to 0.2 x RQ, where RQ is
a resistor connected between ZQ and ground. Alternately, this pin can be connected
directly to VDD, which enables the minimum impedance mode. This pin cannot be
connected directly to GND or left unconnected.
TDO
TCK
Output
Input
Input
Input
N/A
TDO pin for JTAG.
TCK pin for JTAG.
TDI pin for JTAG.
TMS pin for JTAG.
TDI
TMS
NC/36M
Address expansion for 36M. This pin is not connected to the die and so can be tied to
any voltage level on CY7C1303BV25/CY7C1306BV25.
Document #: 38-05627 Rev. **
Page 4 of 19
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
Pin Definitions (continued)
Name
GND/72M
I/O
Input
N/A
Description
Address expansion for 72M. This pin has to be tied to GND on CY7C1303BV25.
NC/72M
Address expansion for 72M. This pin can be tied to any voltage level on
CY7C1306BV25.
GND/144M
Input
Address expansion for 144M. This pin has to be tied to GND on
CY7C1303BV25/CY7C1306BV25.
GND/288M
NC
Input
N/A
Address expansion for 288M. This pin has to be tied to GND on CY7C1306BV25.
Not connected to the die. Can be tied to any voltage level.
VREF
Input-
Reference
Reference Voltage Input. Static input used to set the reference level for HSTL inputs
and Outputs as well as AC measurement points.
VDD
VSS
Power Supply
Ground
Power supply inputs to the core of the device.
Ground for the device.
VDDQ
Power Supply
Power supply inputs for the outputs of the device.
requested data will be valid 2.5 ns from the rising edge of the
output clock (C and C, or K and K when in single clock mode,
167-MHz device).
Introduction
Functional Overview
The CY7C1303BV25/CY7C1306BV25 are synchronous
pipelined Burst SRAM equipped with both a Read port and a
Write port. The Read port is dedicated to Read operations and
the Write port is dedicated to Write operations. Data flows into
the SRAM through the Write port and out through the Read
port. These devices multiplex the address inputs in order to
minimize the number of address pins required. By having
separate Read and Write ports, this architecture completely
eliminates the need to “turn-around” the data bus and avoids
any possible data contention, thereby simplifying system
design. 38-05627Each access consists of two 18-bit data
transfers in the case of CY7C1303BV25, and two 36-bit data
transfers in the case of CY7C1306BV25, in one clock cycle.
Synchronous internal circuitry will automatically three-state
the outputs following the next rising edge of the positive output
clock (C). This will allow for a seamless transition between
devices without the insertion of wait states in a depth
expanded memory.
Write Operations
Write operations are initiated by asserting WPS active at the
rising edge of the positive input clock (K). On the same K clock
rise the data presented to D[17:0] is latched and stored into the
lower 18-bit Write Data register provided BWS[1:0] are both
asserted active. On the subsequent rising edge of the negative
input clock (K), the address is latched and the information
presented to D[17:0] is stored into the Write Data register
provided BWS[1:0] are both asserted active. The 36 bits of data
are then written into the memory array at the specified
location.
Accesses for both ports are initiated on the rising edge of the
Positive Input Clock (K). All synchronous input timing is refer-
enced from the rising edge of the input clocks (K and K) and
all output timings are referenced to rising edge of output clocks
(C and C or K and K when in single clock mode).
When deselected, the Write port will ignore all inputs after the
pending Write operations have been completed.
All synchronous data inputs (D[x:0]) pass through input
registers controlled by the rising edge of the input clocks (K
and K). All synchronous data outputs (Q[x:0]) pass through
output registers controlled by the rising edge of the output
clocks (C and C, or K and K when in single clock mode).
Byte Write Operations
Byte Write operations are supported by the CY7C1303BV25.
A Write operation is initiated as described in the Write
Operation section above. The bytes that are written are deter-
mined by BWS0 and BWS1 which are sampled with each set
of 18-bit data word. Asserting the appropriate Byte Write
Select input during the data portion of a write will allow the data
being presented to be latched and written into the device.
Deasserting the Byte Write Select input during the data portion
of a write will allow the data stored in the device for that byte
to remain unaltered. This feature can be used to simplify
Read/Modify/Write operations to a Byte Write operation.
All synchronous control (RPS, WPS, BWS[x:0]) inputs pass
through input registers controlled by the rising edge of input
clocks (K and K).
The following descriptions take CY7C1303BV25 as an
example. The same basic descriptions apply to
CY7C1306BV25.
Read Operations
The CY7C1303BV25 is organized internally as 2 arrays of
512K x 18. Accesses are completed in a burst of two
sequential 18-bit data words. Read operations are initiated by
asserting RPS active at the rising edge of the positive input
clock (K). The address is latched on the rising edge of the K
clock. Following the next K clock rise the corresponding lower
order 18-bit word of data is driven onto the Q[17:0] using C as
the output timing reference. On the subsequent rising edge of
C the higher order data word is driven onto the Q[17:0]. The
Single Clock Mode
The CY7C1303BV25 can be used with a single clock mode. In
this mode the device will recognize only the pair of input clocks
(K and K) that control both the input and output registers. This
operation is identical to the operation if the device had zero
skew between the K/K and C/C clocks. All timing parameters
remain the same in this mode. To use this mode of operation,
Document #: 38-05627 Rev. **
Page 5 of 19
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
the user must tie C and C HIGH at power-up.This function is
a strap option and not alterable during device operation.
sampled on the rising edge of the Positive Input Clock only (K).
Each port select input can deselect the specified port.
Deselecting a port will not affect the other port. All pending
transactions (Read and Write) will be completed prior to the
device being deselected.
Concurrent Transactions
The Read and Write ports on the CY7C1303BV25 operate
completely independently of one another. Since each port
latches the address inputs on different clock edges, the user
can Read or Write to any location, regardless of the trans-
action on the other port. Also, reads and writes can be started
in the same clock cycle. If the ports access the same location
at the same time, the SRAM will deliver the most recent infor-
mation associated with the specified address location. This
includes forwarding data from a Write cycle that was initiated
on the previous K clock rise.
Programmable Impedance
An external resistor, RQ, must be connected between the ZQ
pin on the SRAM and VSS to allow the SRAM to adjust its
output driver impedance. The value of RQ must be 5X the
value of the intended line impedance driven by the SRAM, The
allowable range of RQ to guarantee impedance matching with
a tolerance of ±15% is between 175Ω and 350Ω, with
VDDQ=1.5V. The output impedance is adjusted every 1024
cycles to account for drifts in supply voltage and temperature.
Depth Expansion
The CY7C1303BV25 has a Port Select input for each port.
This allows for easy depth expansion. Both Port Selects are
Application Example[1]
Note:
1. The above application shows 4 QDR-I being used.
Truth Table[2, 3, 4, 5, 6, 7]
Operation
K
RPS
WPS
DQ
DQ
Write Cycle:
L-H
X
L
D(A+0) at
K(t) ↑
D(A+1) at
K(t) ↑
Load address on the rising edge of K clock; input write
data on K and K rising edges.
Read Cycle:
L-H
L-H
L
X
Q(A+0) at
C(t+1)↑
Q(A+1) at
C(t+1) ↑
Load address on the rising edge of K clock; wait one
cycle; read data on 2 consecutive C and C rising edges.
NOP: No Operation
H
X
H
X
D = X
D = X
Q = High-Z Q = High-Z
Standby: Clock Stopped
Stopped
Previous
State
Previous
State
Document #: 38-05627 Rev. **
Page 6 of 19
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
Write Descriptions (CY7C1303BV25)[2, 8]
BWS0
BWS1
K
L-H
-
K
Comments
During the Data portion of a Write sequence, both bytes (D[17:0]) are written into the device.
L
L
L
L
L
-
L-H During the Data portion of a Write sequence, both bytes (D[17:0]) are written into the device.
H
L-H
-
During the Data portion of a Write sequence, only the lower byte (D[8:0]) is written into the
device. D[17:9] remains unaltered.
L
H
H
H
L
L
-
L-H
-
L-H During the Data portion of a Write sequence, only the lower byte (D[8:0]) is written into the
device. D[17:9] remains unaltered.
-
During the Data portion of a Write sequence, only the byte (D[17:9]) is written into the device.
D[8:0] remains unaltered.
L-H During the Data portion of a Write sequence, only the byte (D[17:9]) is written into the device.
[8:0] remains unaltered.
D
H
H
H
H
L-H
-
-
No data is written into the device during this portion of a write operation.
L-H No data is written into the device during this portion of a write operation.
Write Descriptions (CY7C1306BV25)[2, 8]
BWS0 BWS1 BWS2 BWS3
K
K
Comments
L
L
L
L
L-H
-
During the Data portion of a Write sequence, all four bytes (D[35:0]) are
written into the device.
L
L
L
L
-
L-H
-
L-H During the Data portion of a Write sequence, all four bytes (D[35:0]) are
written into the device.
L
H
H
L
H
H
H
H
L
H
H
H
H
H
H
L
-
During the Data portion of a Write sequence, only the lower byte (D[8:0]
is written into the device. D[35:9] will remain unaltered.
)
L
L-H During the Data portion of a Write sequence, only the lower byte (D[8:0]
is written into the device. D[35:9] will remain unaltered.
)
H
H
H
H
H
H
H
L-H
-
-
During the Data portion of a Write sequence, only the byte (D[17:9]) is
written into the device. D[8:0] and D[35:18] will remain unaltered.
L
L-H During the Data portion of a Write sequence, only the byte (D[17:9]) is
written into the device. D[8:0] and D[35:18] will remain unaltered.
H
H
H
H
L-H
-
-
During the Data portion of a Write sequence, only the byte (D[26:18]) is
written into the device. D[17:0] and D[35:27] will remain unaltered.
L
L-H During the Data portion of a Write sequence, only the byte (D[26:18]) is
written into the device. D[17:0] and D[35:27] will remain unaltered.
H
H
L-H
-
-
During the Data portion of a Write sequence, only the byte (D[35:27]) is
written into the device. D[26:0] will remain unaltered.
L
L-H During the Data portion of a Write sequence, only the byte (D[35:27]) is
written into the device. D[26:0] will remain unaltered.
H
H
H
H
H
H
L-H
-
-
No data is written into the device during this portion of a Write operation.
H
L-H No data is written into the device during this portion of a Write operation.
Notes:
2. X = Don't Care, H = Logic HIGH, L = Logic LOW, ↑represents rising edge.
3. Device will power-up deselected and the outputs in a three-state condition.
4. “A” represents address location latched by the devices when transaction was initiated. A+0, A+1 represent the addresses sequence in the burst.
5. “t” represents the cycle at which a Read/Write operation is started. t+1 is the first clock cycle succeeding the “t” clock cycle.
6. Data inputs are registered at K and K rising edges. Data outputs are delivered on C and C rising edges, except when in single clock mode.
7. It is recommended that K = K and C = C when clock is stopped. This is not essential, but permits most rapid restart by overcoming transmission line charging
symmetrically.
8. Assumes a Write cycle was initiated per the Write Port Cycle Description Truth Table. BWS , BWS , in the case of CY7C1303BV25 and also BWS and BWS
0
1
2
3
in the case of CY7C1306BV25 can be altered on different portions of a write cycle, as long as the set-up and hold requirements are achieved. 38-05627
Document #: 38-05627 Rev. **
Page 7 of 19
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
Current into Outputs (LOW)......................................... 20 mA
Maximum Ratings
Static Discharge Voltage.......................................... > 2001V
(per MIL-STD-883, Method 3015)
(Above which the useful life may be impaired.)
Storage Temperature .................................–65°C to +150°C
Latch-up Current.................................................... > 200 mA
Ambient Temperature with
Power Applied.............................................–55°C to +125°C
Operating Range
Supply Voltage on VDD Relative to GND........ –0.5V to +3.6V
DC Applied to Outputs in High-Z State –0.5V to VDDQ + 0.5V
DC Input Voltage[13] ............................ –0.5V to VDDQ + 0.5V
Ambient
[9]
[9]
Range Temperature (TA)
VDD
2.5 ± 0.1V
VDDQ
1.4V to 1.9V
Com’l
0°C to +70°C
Electrical Characteristics Over the Operating Range[10]
DC Electrical Characteristics
Parameter
VDD
Description
Power Supply Voltage
I/O Supply Voltage
Test Conditions
Min.
2.4
Typ.
Max.
Unit
V
2.5
1.5
2.6
1.9
VDDQ
VOH
1.4
V
Output HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage[13]
Input LOW Voltage[13, 14]
Note 11
Note 12
VDDQ/2 – 0.12
VDDQ/2 – 0.12
VDDQ/2 + 0.12
VDDQ/2 + 0.12
VDDQ
V
VOL
V
VOH(LOW)
VOL(LOW)
VIH
IOH = –0.1 mA, Nominal Impedance VDDQ – 0.2
V
IOL = 0.1 mA, Nominal Impedance
VSS
VREF + 0.1
–0.3
0.2
V
VDDQ + 0.3
VREF – 0.1
0.95
V
VIL
V
VREF
IX
Input Reference Voltage[15] Typical value = 0.75V
0.68
0.75
V
Input Load Current
GND ≤ VI ≤ VDDQ
–5
5
µA
µA
mA
mA
mA
mA
mA
mA
IOZ
Output Leakage Current
VDD Operating Supply
GND ≤ VI ≤ VDDQ, Output Disabled
–5
5
IDD
VDD = Max.,
OUT = 0 mA,
f = fMAX = 1/tCYC
167 MHz
133 MHz
100 MHz
TBD
I
TBD
TBD
ISB1
Automatic
Power-Down
Current
Max. VDD, Both Ports 167 MHz
TBD
Deselected, VIN ≥ VIH
133 MHz
TBD
or VIN ≤ VIL f = fMAX
=
100 MHz
TBD
1/tCYC, Inputs Static
AC Input Requirements
Parameter
Description
Test Conditions
Min.
VREF + 0.2
–
Typ.
Max.
–
Unit
V
VIH
VIL
Input High (Logic 1) Voltage
Input Low (Logic 0) Voltage
–
–
VREF – 0.2
V
Thermal Resistance[16]
Parameter
Description
Test Conditions
165 FBGA Package
Unit
ΘJA
Thermal Resistance
(Junction to Ambient)
Testconditionsfollowstandardtestmethodsand
procedures for measuring thermal impedance,
per EIA/JESD51.
16.7
°C/W
ΘJC
Thermal Resistance
(Junction to Case)
6.5
°C/W
Notes:
9. Power-up: Assumes a linear ramp from 0V to V (min.) within 200 ms. During this time V < V and V
< V .
DD
DD
IH
DD
DDQ
10. All Voltage referenced to Ground.
11. Output are impedance controlled. I = –V
/2)/(RQ/5) for values of 175Ω <= RQ <= 350Ω.
OH
DDQ
12. Output are impedance controlled. I = (V
/2)/(RQ/5) for values of 175Ω <= RQ <= 350Ω.
OL
DDQ
13. Overshoot: V (AC) < V
+0.85V (Pulse width less than t
/2), Undershoot: V (AC) > –1.5V (Pulse width less than t
/2).
IH
DDQ
CYC
IL
CYC
14. This spec is for all inputs except C and C Clock. For C and C Clock, V (Max.) = V
– 0.2V.
IL
REF
15. VREF (Min.) = 0.68V or 0.46V
, whichever is larger, V
(Max.) = 0.95V or 0.54V
, whichever is smaller.
DDQ
DDQ
REF
16. Tested initially and after any design or process change that may affect these parameters.
Document #: 38-05627 Rev. **
Page 8 of 19
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
Capacitance[19]
Parameter
Description
Test Conditions
Max.
Unit
pF
CIN
Input Capacitance
TA = 25°C, f = 1 MHz,
DD = 2.5V.
DDQ = 1.5V
5
6
7
V
V
CCLK
CO
Clock Input Capacitance
Output Capacitance
pF
pF
AC Test Loads and Waveforms
VDDQ/2
VDDQ/2
VREF
VREF
VDDQ/2
R = 50Ω
OUTPUT
[15]
ALL INPUT PULSES
1.25V
Z = 50Ω
0
OUTPUT
Device
Under
Test
R = 50Ω
L
0.75V
Device
Under
0.25V
5 pF
VREF = 0.75V
ZQ
Test
RQ =
250Ω
ZQ
RQ =
250Ω
(a)
INCLUDING
JIG AND
SCOPE
(b)
Switching Characteristics Over the Operating Range [17]
167 MHz
133 MHz
100 MHz
Cypress Consortium
Parameter Parameter
Description
Min. Max. Min. Max. Min. Max. Unit
[18]
tPower
VCC (typical) to the First Access Read or Write
10
10
10
µs
Cycle Time
tCYC
tKH
tKHKH
tKHKL
tKLKH
tKHKH
K Clock and C Clock Cycle Time
Input Clock (K/K and C/C) HIGH
Input Clock (K/K and C/C) LOW
6.0
2.4
2.4
7.5
3.2
3.2
10.0
3.5
ns
ns
ns
ns
tKL
3.5
tKHKH
K/K Clock Rise to K/K Clock Rise and C/C to C/C Rise 2.7 3.3 3.4 4.1 4.4 5.4
(rising edge to rising edge)
tKHCH
tKHCH
K/K Clock Rise to C/C Clock Rise
(rising edge to rising edge)
0.0 2.0 0.0 2.5 0.0 3.0
ns
Set-up Times
tSA tSA
tSC tSC
Address Set-up to Clock (K and K) Rise
0.7
0.7
0.8
0.8
1.0
1.0
ns
ns
Control Set-up to Clock (K and K) Rise (RPS, WPS,
BWS0, BWS1)
tSD
tSD
D[x:0] Set-up to Clock (K and K) Rise
0.7
0.8
1.0
ns
Hold Times
tHA
tHC
tHA
tHC
Address Hold after Clock (K and K) Rise
0.7
0.8
0.8
1.0
1.0
ns
ns
Control Signals Hold after Clock (K and K) Rise (RPS, 0.7
WPS, BWS0, BWS1)
tHD
tHD
D[x:0] Hold after Clock (K and K) Rise
0.7
0.8
1.0
ns
Notes:
17. Unless otherwise noted, test conditions assume signal transition time of 2V/ns, timing reference levels of 0.75V,Vref = 0.75V, RQ = 250Ω, V
= 1.5V, input
DDQ
pulse levels of 0.25V to 1.25V, and output loading of the specified I /I and load capacitance shown in (a) of AC test loads.
OL OH
18. This part has a voltage regulator that steps down the voltage internally; t
is the time power needs to be supplied above V minimum initially before a read
Power
DD
or write operation can be initiated.
19. At any given voltage and temperature t
is less than t
and, t
less than t
.
CHZ
CLZ
CHZ
CO
Document #: 38-05627 Rev. **
Page 9 of 19
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
Switching Characteristics Over the Operating Range (continued)[17]
167 MHz
133 MHz
100 MHz
Cypress Consortium
Parameter Parameter
Description
Min. Max. Min. Max. Min. Max. Unit
Output Times
tCO
tCHQV
tCHQX
C/C Clock Rise (or K/K in single clock mode) to Data
Valid
2.5
2.5
3.0
3.0
3.0
3.0
ns
ns
tDOH
Data Output Hold after Output C/C Clock Rise (Active to 1.2
Active)
Clock (C and C) rise to High-Z (Active to High-Z)[20, 19]
Clock (C and C) rise to Low-Z[20, 19]
1.2
1.2
1.2
1.2
tCHZ
tCLZ
tCHZ
tCLZ
ns
ns
1.2
Switching Waveforms[21, 22, 23]
READ
1
WRITE
2
READ
3
WRITE
4
READ
5
WRITE
6
NOP
WRITE
NOP
7
8
10
9
K
t
t
t
t
KHKH
KH
KL
CYC
K
RPS
tSC
tHC
WPS
A
A5
A6
A0
A1
A2
A3
A4
t
t
t
t
SA HA
SA HA
D
Q
D10
D11
D30
D31
D50
D51
D60
D61
t
t
t
SD
HD
HD
t
SD
Q00
Q01
Q20
Q21
Q40
Q41
t
CHZ
t
t
t
DOH
DOH
CLZ
t
t
t
t
CO
KHCH
KHCH
CO
C
t
t
t
KHKH
tCYC
KH
KL
C
DON’T CARE
UNDEFINED
Notes:
20. t
, t
, are specified with a load capacitance of 5 pF as in part (b) of AC Test Loads. Transition is measured ± 100 mV from steady-state voltage.
CHZ CLZ
21. Q00 refers to output from address A0. Q01 refers to output from the next internal burst address following A0, i.e., A0+1.
22. Outputs are disabled (High-Z) one clock cycle after a NOP.
23. In this example, if address A2 = A1 then data Q2 0= D10 and Q21 = D11. Write data is forwarded immediately as read results.This note applies to the whole diagram.
Document #: 38-05627 Rev. **
Page 10 of 19
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
TDI and TDO pins as shown in TAP Controller Block Diagram.
Upon power-up, the instruction register is loaded with the
IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state as
described in the previous section.
IEEE 1149.1 Serial Boundary Scan (JTAG)
These SRAMs incorporate a serial boundary scan test access
port (TAP) in the FBGA package. This part is fully compliant
with IEEE Standard #1149.1-1900. The TAP operates using
JEDEC standard 2.5V I/O logic levels.
When the TAP controller is in the Capture IR state, the two
least significant bits are loaded with a binary “01” pattern to
allow for fault isolation of the board level serial test path.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(VSS) to prevent clocking of the device. TDI and TMS are inter-
nally pulled up and may be unconnected. They may alternately
be connected to VDD through a pull-up resistor. TDO should
be left unconnected. Upon power-up, the device will come up
in a reset state which will not interfere with the operation of the
device.
Bypass Register
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between TDI
and TDO pins. This allows data to be shifted through the
SRAM with minimal delay. The bypass register is set LOW
(VSS) when the BYPASS instruction is executed.
Test Access Port—Test Clock
Boundary Scan Register
The test clock is used only with the TAP controller. All inputs
are captured on the rising edge of TCK. All outputs are driven
from the falling edge of TCK.
The boundary scan register is connected to all of the input and
output pins on the SRAM. Several no connect (NC) pins are
also included in the scan register to reserve pins for higher
density devices.
Test Mode Select
The boundary scan register is loaded with the contents of the
RAM Input and Output ring when the TAP controller is in the
Capture-DR state and is then placed between the TDI and
TDO pins when the controller is moved to the Shift-DR state.
The EXTEST, SAMPLE/PRELOAD and SAMPLE Z instruc-
tions can be used to capture the contents of the Input and
Output ring.
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. It is allowable to
leave this pin unconnected if the TAP is not used. The pin is
pulled up internally, resulting in a logic HIGH level.
Test Data-In (TDI)
The TDI pin is used to serially input information into the
registers and can be connected to the input of any of the
registers. The register between TDI and TDO is chosen by the
instruction that is loaded into the TAP instruction register. For
information on loading the instruction register, see the TAP
Controller State Diagram. TDI is internally pulled up and can
be unconnected if the TAP is unused in an application. TDI is
connected to the most significant bit (MSB) on any register.
The Boundary Scan Order tables show the order in which the
bits are connected. Each bit corresponds to one of the bumps
on the SRAM package. The MSB of the register is connected
to TDI, and the LSB is connected to TDO.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired
into the SRAM and can be shifted out when the TAP controller
is in the Shift-DR state. The ID register has a vendor code and
other information described in the Identification Register
Definitions table.
Test Data-Out (TDO)
The TDO output pin is used to serially clock data-out from the
registers. The output is active depending upon the current
state of the TAP state machine (see Instruction codes). The
output changes on the falling edge of TCK. TDO is connected
to the least significant bit (LSB) of any register.
TAP Instruction Set
Performing a TAP Reset
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in the
Instruction Code table. Three of these instructions are listed
as RESERVED and should not be used. The other five instruc-
tions are described in detail below.
A Reset is performed by forcing TMS HIGH (VDD) for five rising
edges of TCK. This RESET does not affect the operation of
the SRAM and may be performed while the SRAM is
operating. At power-up, the TAP is reset internally to ensure
that TDO comes up in a high-Z state.
Instructions are loaded into the TAP controller during the
Shift-IR state when the instruction register is placed between
TDI and TDO. During this state, instructions are shifted
through the instruction register through the TDI and TDO pins.
To execute the instruction once it is shifted in, the TAP
controller needs to be moved into the Update-IR state.
TAP Registers
Registers are connected between the TDI and TDO pins and
allow data to be scanned into and out of the SRAM test
circuitry. Only one register can be selected at a time through
the instruction registers. Data is serially loaded into the TDI pin
on the rising edge of TCK. Data is output on the TDO pin on
the falling edge of TCK.
IDCODE
The IDCODE instruction causes a vendor-specific, 32-bit code
to be loaded into the instruction register. It also places the
instruction register between the TDI and TDO pins and allows
the IDCODE to be shifted out of the device when the TAP
controller enters the Shift-DR state. The IDCODE instruction
Instruction Register
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the
Document #: 38-05627 Rev. **
Page 11 of 19
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
is loaded into the instruction register upon power-up or
whenever the TAP controller is given a test logic reset state.
The shifting of data for the SAMPLE and PRELOAD phases
can occur concurrently when required—that is, while data
captured is shifted out, the preloaded data can be shifted in.
SAMPLE Z
BYPASS
The SAMPLE Z instruction causes the boundary scan register
to be connected between the TDI and TDO pins when the TAP
controller is in a Shift-DR state. The SAMPLE Z command puts
the output bus into a High-Z state until the next command is
given during the “Update IR” state.
When the BYPASS instruction is loaded in the instruction
register and the TAP is placed in a Shift-DR state, the bypass
register is placed between the TDI and TDO pins. The
advantage of the BYPASS instruction is that it shortens the
boundary scan path when multiple devices are connected
together on a board.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the inputs and output pins is
captured in the boundary scan register.
EXTEST
The EXTEST instruction enables the preloaded data to be
driven out through the system output pins. This instruction also
selects the boundary scan register to be connected for serial
access between the TDI and TDO in the shift-DR controller
state.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 10 MHz, while the SRAM clock
operates more than an order of magnitude faster. Because
there is a large difference in the clock frequencies, it is
possible that during the Capture-DR state, an input or output
will undergo a transition. The TAP may then try to capture a
signal while in transition (metastable state). This will not harm
the device, but there is no guarantee as to the value that will
be captured. Repeatable results may not be possible.
EXTEST Output Bus Three-state
IEEE Standard 1149.1 mandates that the TAP controller be
able to put the output bus into a three-state mode.
The boundary scan register has a special bit located at bit #47.
When this scan cell, called the “extest output bus three-state”,
is latched into the preload register during the “Update-DR”
state in the TAP controller, it will directly control the state of the
output (Q-bus) pins, when the EXTEST is entered as the
current instruction. When HIGH, it will enable the output
buffers to drive the output bus. When LOW, this bit will place
the output bus into a High-Z condition.
To guarantee that the boundary scan register will capture the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller's capture set-up plus
hold times (tCS and tCH). The SRAM clock input might not be
captured correctly if there is no way in a design to stop (or
slow) the clock during a SAMPLE/PRELOAD instruction. If this
is an issue, it is still possible to capture all other signals and
simply ignore the value of the CK and CK captured in the
boundary scan register.
This bit can be set by entering the SAMPLE/PRELOAD or
EXTEST command, and then shifting the desired bit into that
cell, during the “Shift-DR” state. During “Update-DR”, the value
loaded into that shift-register cell will latch into the preload
register. When the EXTEST instruction is entered, this bit will
directly control the output Q-bus pins. Note that this bit is
pre-set HIGH to enable the output when the device is
powered-up, and also when the TAP controller is in the
“Test-Logic-Reset” state.
Once the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the
boundary scan register between the TDI and TDO pins.
PRELOAD allows an initial data pattern to be placed at the
latched parallel outputs of the boundary scan register cells
prior to the selection of another boundary scan test operation.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
Document #: 38-05627 Rev. **
Page 12 of 19
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
TAP Controller State Diagram[24]
TEST-LOGIC
1
RESET
0
1
1
1
TEST-LOGIC/
IDLE
SELECT
DR-SCAN
SELECT
IR-SCAN
0
0
0
1
1
CAPTURE-DR
CAPTURE-DR
0
0
SHIFT-DR
0
SHIFT-IR
0
1
1
1
EXIT1-IR
0
1
0
EXIT1-DR
0
0
PAUSE-DR
1
PAUSE-IR
1
0
0
EXIT2-DR
EXIT2-IR
1
1
UPDATE-DR
UPDATE-IR
1
1
0
0
Note:
24. The 0/1 next to each state represents the value at TMS at the rising edge of TCK.
Document #: 38-05627 Rev. **
Page 13 of 19
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
TAP Controller Block Diagram
0
Bypass Register
Selection
TDI
Selection
Circuitry
2
1
0
0
0
TDO
Circuitry
Instruction Register
29
31 30
.
.
2
1
Identification Register
.
106 .
.
.
2
1
Boundary Scan Register
TCK
TMS
TAP Controller
TAP Electrical Characteristics Over the Operating Range [10, 13, 25]
Parameter
VOH1
VOH2
VOL1
VOL2
VIH
Description
Output HIGH Voltage
Output HIGH Voltage
Output LOW Voltage
Output LOW Voltage
Input HIGH Voltage
Test Conditions
IOH = −2.0 mA
Min.
1.7
Max.
Unit
V
V
IOH = −100 µA
IOL = 2.0 mA
IOL = 100 µA
2.1
0.7
0.2
V
V
1.7
–0.3
−5
VDD + 0.3
0.7
V
VIL
Input LOW Voltage
V
IX
Input and Output Load Current
GND ≤ VI ≤ VDDQ
5
µA
TAP AC Switching Characteristics Over the Operating Range[26, 27]
Parameter
tTCYC
Description
Min.
Max.
Unit
TCK Clock Cycle Time
TCK Clock Frequency
TCK Clock HIGH
100
ns
MHz
ns
tTF
10
tTH
40
40
tTL
TCK Clock LOW
ns
Set-up Times
tTMSS
tTDIS
TMS Set-up to TCK Clock Rise
TDI Set-up to TCK clock Rise
Capture Set-up to TCK Rise
10
10
10
ns
ns
ns
tCS
Hold Times
tTMSH
tTDIH
TMS Hold after TCK Clock Rise
TDI Hold after Clock Rise
10
10
10
ns
ns
ns
tCH
Capture Hold after Clock Rise
Notes:
25. These characteristic pertain to the TAP inputs (TMS, TCK, TDI and TDO). Parallel load levels are specified in the Electrical Characteristics table.
26. t and t refer to the set-up and hold time requirements of latching data from the boundary scan register.
CS
CH
27. Test conditions are specified using the load in TAP AC test conditions. t /t = 1 ns.
R
F
Document #: 38-05627 Rev. **
Page 14 of 19
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
TAP AC Switching Characteristics Over the Operating Range[26, 27] (continued)
Parameter
Output Times
tTDOV
Description
Min.
Max.
Unit
TCK Clock LOW to TDO Valid
TCK Clock LOW to TDO Invalid
20
ns
ns
tTDOX
0
TAP Timing and Test Conditions[27]
1.25V
50Ω
ALL INPUT PULSES
1.25V
TDO
2.5V
Z = 50Ω
0
C = 20 pF
L
0V
(a)
GND
tTL
tTH
Test Clock
TCK
tTCYC
tTMSS
tTMSH
Test Mode Select
TMS
tTDIS
tTDIH
Test Data-In
TDI
Test Data-Out
TDO
tTDOX
tTDOV
Identification Register Definitions
Value
Instruction Field
Revision Number (31:29)
Cypress Device ID (28:12)
Cypress JEDEC ID (11:1)
ID Register Presence (0)
CY7C1303BV25
CY7C1306BV25
Description
Version number.
000
01011010010010101
00000110100
1
000
01011010010100101 Defines the type of SRAM.
00000110100
1
Allows unique identification of SRAM vendor.
Indicate the presence of an ID register.
Document #: 38-05627 Rev. **
Page 15 of 19
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
Scan Register Sizes
Register Name
Instruction
Bit Size
3
1
Bypass
ID
32
107
Boundary Scan
Instruction Codes
Instruction
EXTEST
Code
Description
000
001
Captures the Input/Output ring contents.
IDCODE
Loads the ID register with the vendor ID code and places the register
between TDI and TDO. This operation does not affect SRAM operation.
SAMPLE Z
010
Captures the Input/Output contents. Places the boundary scan register
between TDI and TDO. Forces all SRAM output drivers to a High-Z state.
RESERVED
011
100
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
Captures the Input/Output ring contents. Places the boundary scan register
between TDI and TDO. Does not affect the SRAM operation.
RESERVED
RESERVED
BYPASS
101
110
111
Do Not Use: This instruction is reserved for future use.
Do Not Use: This instruction is reserved for future use.
Places the bypass register between TDI and TDO. This operation does not
affect SRAM operation.
Boundary Scan Order
Boundary Scan Order (continued)
Bit #
0
Bump ID
6R
Bit #
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Bump ID
9K
1
6P
10J
11J
2
6N
3
7P
11H
10G
9G
4
7N
5
7R
6
8R
11F
11G
9F
7
8P
8
9R
9
11P
10P
10N
9P
10F
11E
10E
10D
9E
10
11
12
13
14
15
16
17
18
19
20
21
22
23
10M
11N
9M
10C
11D
9C
9N
11L
11M
9L
9D
11B
11C
9B
10L
11K
10K
9J
10B
11A
Internal
Document #: 38-05627 Rev. **
Page 16 of 19
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
Boundary Scan Order (continued)
Boundary Scan Order (continued)
Bit #
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
Bump ID
Bit #
92
Bump ID
1L
9A
8B
7C
6C
8A
7A
7B
6B
6A
5B
5A
4A
5C
4B
3A
1H
1A
2B
3B
1C
1B
3D
3C
1D
2C
3E
2D
2E
1E
2F
3F
1G
1F
3G
2G
1J
93
3N
94
3M
1N
95
96
2M
3P
97
98
2N
99
2P
100
101
102
103
104
105
106
1P
3R
4R
4P
5P
5N
5R
2J
3K
3J
2K
1K
2L
3L
1M
Document #: 38-05627 Rev. **
Page 17 of 19
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
Ordering Information
Speed
Package
Name
Operating
Range
(MHz)
Ordering Code
Package Type
13 x 15 x 1.4 mm FBGA
167
CY7C1303BV25-167BZC
CY7C1306BV25-167BZC
CY7C1303BV25-133BZC
CY7C1306BV25-133BZC
CY7C1303BV25-100BZC
CY7C1306BV25-100BZC
BB165D
BB165D
BB165D
Commercial
133
100
13 x 15 x 1.4 mm FBGA
13 x 15 x 1.4 mm FBGA
Package Diagram
165 FBGA 13 x 15 x 1.40 mm BB165D
51-85180-**
Quad Data Rate™ SRAM and QDR™ SRAM comprise a new family of products developed by Cypress, IDT, NEC and Samsung.
All products and company names mentioned in this document may be the trademarks of their respective holders.
Document #: 38-05627 Rev. **
Page 18 of 19
© Cypress Semiconductor Corporation, 2004. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
CY7C1303BV25
CY7C1306BV25
PRELIMINARY
Document History Page
Document Title: CY7C1303BV25/CY7C1306BV25 18-Mbit Burst of 2 Pipelined SRAM with QDR™ Architecture
Document Number: 38-05627
Orig. of
REV.
ECN NO.
Issue Date
Change
Description of Change
New Data Sheet
**
253010
See ECN
SYT
Document #: 38-05627 Rev. **
Page 19 of 19
相关型号:
CY7C1303V25-100BZC
QDR SRAM, 1MX18, 3ns, CMOS, PBGA165, 13 X 15 MM, 1.20 MM HEIGHT, FBGA-165
CYPRESS
©2020 ICPDF网 联系我们和版权申明