CY7C1463AV33-133BZI [CYPRESS]
36-Mbit (1M x 36/2 M x 18/512K x 72) Flow-Through SRAM with NoBL⑩ Architecture; 36兆位（ 1M X 36/2的M× 18 / 512K X 72 ）流通型SRAM与NoBL⑩架构
| 型号： | CY7C1463AV33-133BZI |
| 厂家： | 
CYPRESS |
| 描述： | 36-Mbit (1M x 36/2 M x 18/512K x 72) Flow-Through SRAM with NoBL⑩ Architecture |
| 文件： | 总31页 (文件大小：1144K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
36-Mbit (1M x 36/2 M x 18/512K x 72)
Flow-ThroughSRAMwithNoBL™Architecture
Features
Functional Description[1]
• No Bus Latency™ (NoBL™) architecture eliminates dead
cycles between write and read cycles
The CY7C1461AV33/CY7C1463AV33/CY7C1465AV33 is a
3.3V, 1M x 36/2M x 18/512K x 72 Synchronous Flow -through
Burst SRAM designed specifically to support unlimited true
back-to-back Read/Write operations without the insertion of
wait states. The CY7C1461AV33/CY7C1463AV33/CY7C1465AV33
is equipped with the advanced No Bus Latency (NoBL) logic
required to enable consecutive Read/Write operations with
data being transferred on every clock cycle. This feature
dramatically improves the throughput of data through the
SRAM, especially in systems that require frequent Write-Read
transitions.
• Supports up to 133-MHz bus operations with zero wait
states
— Data is transferred on every clock
• Pin-compatible and functionally equivalent to ZBT™
devices
• Internally self timed output buffer control to eliminate the
need to use OE
• Registered inputs for flow through operation
• Byte Write capability
All synchronous inputs pass through input registers controlled
by the rising edge of the clock. The clock input is qualified by
the Clock Enable (CEN) signal, which when deasserted
suspends operation and extends the previous clock cycle.
Maximum access delay from the clock rise is 6.5 ns (133-MHz
device).
• 3.3V/2.5V IO power supply
• Fast clock-to-output times
— 6.5 ns (for 133-MHz device)
Write operations are controlled by the two or four Byte Write
Select (BWX) and a Write Enable (WE) input. All writes are
conducted with on-chip synchronous self timed write circuitry.
• Clock Enable (CEN) pin to enable clock and suspend
operation
• Synchronous self timed writes
• Asynchronous Output Enable
Three synchronous Chip Enables (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) provide for easy bank
selection and output tri-state control. To avoid bus contention,
the output drivers are synchronously tri-stated during the data
portion of a write sequence.
• CY7C1461AV33, CY7C1463AV33 available in
JEDEC-standard Pb-free 100-pin TQFP package, Pb-free
and non-Pb-free 165-Ball FBGA package. CY7C1465AV33
available in Pb-free and non-Pb-free 209-Ball FBGA
package
• Three chip enables for simple depth expansion
• Automatic Power down feature available using ZZ mode or
CE deselect
• IEEE 1149.1 JTAG-Compatible Boundary Scan
• Burst Capability — linear or interleaved burst order
• Low standby power
Selection Guide
133 MHz
6.5
100 MHz
8.5
Unit
ns
Maximum Access Time
Maximum Operating Current
Maximum CMOS Standby Current
310
290
mA
mA
120
120
Note:
1. For best-practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com.
Cypress Semiconductor Corporation
Document #: 38-05356 Rev. *F
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised July 09, 2007
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Logic Block Diagram – CY7C1461AV33 (1M x 36)
ADDRESS
REGISTER
A0, A1,
A
A1
A0
A1'
A0'
D1
D0
Q1
Q0
MODE
BURST
LOGIC
CE
ADV/LD
CLK
CEN
C
C
WRITE ADDRESS
REGISTER
O
U
T
P
U
T
D
A
T
S
E
N
S
E
ADV/LD
A
B
U
F
F
E
R
S
MEMORY
ARRAY
BW
BW
BW
BW
A
WRITE
DRIVERS
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
S
T
E
E
R
I
DQs
DQP
DQP
DQP
DQP
B
A
B
A
M
P
C
C
D
D
S
WE
E
N
G
INPUT
REGISTER
E
OE
CE1
CE2
CE3
READ LOGIC
SLEEP
CONTROL
ZZ
Logic Block Diagram – CY7C1463AV33 (2M x 18)
ADDRESS
REGISTER
A0, A1, A
A1
A0
A1'
A0'
D1
D0
Q1
Q0
MODE
C
BURST
LOGIC
CE
ADV/LD
CLK
CEN
C
WRITE ADDRESS
REGISTER
O
U
T
P
U
T
D
A
T
S
E
N
S
E
ADV/LD
A
B
U
F
F
E
R
S
MEMORY
ARRAY
BW
BW
A
WRITE
DRIVERS
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
S
T
E
E
R
I
DQs
DQP
DQP
B
A
B
A
M
P
S
WE
E
N
G
INPUT
REGISTER
E
OE
CE1
CE2
CE3
READ LOGIC
SLEEP
ZZ
CONTROL
Document #: 38-05356 Rev. *F
Page 2 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Logic Block Diagram – CY7C1465AV33 (512K x 72)
ADDRESS
REGISTER
A0, A1, A
0
A1
A0
A1'
A0'
D1
D0
Q1
Q0
BURST
LOGIC
MODE
C
ADV/LD
CLK
CEN
C
WRITE ADDRESS
REGISTER
WRITE ADDRESS
REGISTER 2
1
O
U
T
O
U
T
P
U
T
S
E
P
U
T
D
A
T
ADV/LD
N
S
A
BW
BW
BW
BW
BW
BW
BW
BW
a
R
E
G
I
MEMORY
ARRAY
E
B
U
F
F
E
R
S
DQ s
DQ P
DQ P
DQ P
DQ P
DQ P
DQ P
DQ P
DQ P
WRITE
DRIVERS
b
c
S
T
E
E
R
I
A
M
P
a
b
c
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
S
T
E
R
S
d
e
S
d
e
f
f
N
G
g
E
E
h
g
h
WE
INPUT
REGISTER 1
INPUT
REGISTER 0
E
E
OE
CE1
CE2
CE3
READ LOGIC
Sleep
Control
ZZ
Document #: 38-05356 Rev. *F
Page 3 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Pin Configurations
100-Pin TQFP Pinout
DQPC
DQC
DQC
VDDQ
VSS
80
1
DQPB
DQB
DQB
VDDQ
VSS
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
2
3
4
5
DQC
6
DQB
DQB
DQB
DQB
VSS
BYTE C
BYTE B
DQC
DQC
DQC
VSS
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
VDDQ
DQC
DQC
NC
VDDQ
DQB
DQB
VSS
VDD
NC
NC
CY7C1461AV33
VDD
ZZ
VSS
DQD
DQD
VDDQ
VSS
DQA
DQA
VDDQ
VSS
BYTE D
DQD
DQA
DQA
DQA
DQA
VSS
DQD
DQD
DQD
VSS
BYTE A
VDDQ
DQD
DQD
DQPD
VDDQ
DQA
DQA
DQPA
Document #: 38-05356 Rev. *F
Page 4 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Pin Configurations (continued)
100-Pin TQFP Pinout
NC
1
80
A
NC
2
NC
3
VDDQ
4
VSS
5
NC
6
NC
7
DQB
8
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
NC
NC
VDDQ
VSS
NC
DQPA
DQA
DQA
VSS
VDDQ
DQA
DQA
VSS
NC
DQB
VSS
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
VDDQ
DQB
DQB
NC
BYTE A
VDD
NC
CY7C1463AV33
BYTE B
VDD
ZZ
VSS
DQB
DQB
VDDQ
VSS
DQA
DQA
VDDQ
VSS
DQA
DQA
NC
DQB
DQB
DQPB
NC
NC
VSS
VSS
VDDQ
NC
VDDQ
NC
NC
NC
NC
NC
Document #: 38-05356 Rev. *F
Page 5 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Pin Configurations (continued)
165-Ball FBGA (15 x 17 x 1.4 mm) Pinout
CY7C1461AV33 (1M x 36)
1
2
A
3
CE1
4
BWC
5
BWB
6
CE3
7
8
9
A
10
A
11
NC
NC/576M
NC/1G
DQPC
DQC
CEN
WE
VSS
VSS
ADV/LD
A
B
C
D
A
CE2
VDDQ
VDDQ
BWD
VSS
BWA
VSS
VSS
CLK
VSS
VSS
OE
VSS
VDD
A
A
NC
NC
DQC
VDDQ
VDDQ
NC
DQPB
DQB
VDD
DQB
DQC
DQC
DQC
NC
DQC
DQC
DQC
NC
VDDQ
VDDQ
VDDQ
NC
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDDQ
VDDQ
VDDQ
NC
DQB
DQB
DQB
NC
DQB
DQB
DQB
ZZ
E
F
G
H
J
DQD
DQD
DQD
DQD
DQD
DQD
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
DQA
DQA
DQA
DQA
DQA
DQA
K
L
DQD
DQD
NC
VDDQ
VDDQ
A
VDD
VSS
A
VSS
NC
VSS
NC
A1
VSS
NC
VDD
VSS
A
VDDQ
VDDQ
A
DQA
NC
A
DQA
DQPA
M
N
P
DQPD
NC/144M NC/72M
TDI
TDO
NC/288M
A0
MODE
A
A
A
TMS
TCK
A
A
A
A
R
CY7C1463AV33 (2M x 18)
1
NC/576M
NC/1G
NC
2
3
CE1
4
BWB
5
NC
6
CE3
7
8
9
A
10
A
11
A
CEN
WE
VSS
VSS
ADV/LD
A
B
C
D
A
A
CE2
VDDQ
VDDQ
NC
VSS
VDD
BWA
VSS
VSS
CLK
VSS
VSS
OE
VSS
VDD
A
A
NC
NC
DQB
VDDQ
VDDQ
NC
NC
DQPA
DQA
NC
NC
NC
DQB
DQB
DQB
NC
VDDQ
VDDQ
VDDQ
NC
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDDQ
VDDQ
VDDQ
NC
NC
NC
DQA
DQA
DQA
ZZ
E
F
NC
NC
G
H
J
NC
NC
DQB
DQB
DQB
NC
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
DQA
DQA
DQA
NC
NC
NC
K
L
NC
NC
DQB
NC
NC
VDDQ
VDDQ
A
VDD
VSS
A
VSS
NC
VSS
NC
A1
VSS
NC
VDD
VSS
A
VDDQ
VDDQ
A
DQA
NC
A
NC
NC
M
N
P
DQPB
NC/144M NC/72M
MODE
TDI
TDO
NC/288M
A0
A
A
TMS
TCK
A
A
A
A
A
R
Document #: 38-05356 Rev. *F
Page 6 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Pin Configurations (continued)
209-Ball FBGA (14 x 22 x 1.76 mm) Pinout
CY7C1465AV33 (512K × 72)
1
2
3
4
5
6
7
8
9
10
DQb
DQb
11
A
B
C
D
E
F
DQg
DQg
DQg
DQg
CE3
A
CE2
A
ADV/LD
WE
A
A
A
DQb
DQb
BWSb
NC
BWSc
BWSh
VSS
BWSf
BWSg
BWSd
DQg
DQg
DQg
DQg
DQPc
DQc
DQc
NC/576M
NC
NC
BWSe
NC
CE1
BWSa DQb
DQb
DQb
DQPb
DQf
NC/1G OE
VSS
NC
DQb
DQPg
DQc
VDDQ
VDDQ
VDDQ
DQPf
VDDQ
VSS
VDDQ
VSS
VDD
VSS
VDD
VSS
VDD
VSS
VDD
VDD
VDD
VSS
VDD
VSS
DQf
VSS
VDDQ
VSS
NC
NC
NC
NC
CEN
NC
NC
VSS
G
H
J
DQc
DQc
VDDQ
VSS
VDDQ
VSS
DQf
DQf
DQf
VSS
VDD
VSS
VDD
VSS
VDD
VSS
VDD
NC
A
DQc
DQc
NC
DQf
DQf
NC
VDDQ
DQc
NC
VDDQ
VDDQ
NC
VDDQ
CLK
DQf
NC
K
L
NC
NC
DQh
DQh
DQh
VDDQ
VSS
VDDQ
VSS
VDDQ
VDDQ
VSS
VDDQ
VSS
VDDQ
VSS
DQa
DQa
DQa
M
N
P
R
T
VSS
VDDQ
VSS
VDDQ
NC
DQh
DQh
DQh
VSS
VDD
VSS
DQa
DQa
DQa
VDDQ
DQh
DQh
DQPd
DQd
DQd
NC
ZZ
DQa
DQa
DQPa
DQe
DQe
VSS
VDDQ
VDDQ
VDD
NC
DQPh
DQd
DQd
DQd
DQd
VDDQ
VDD
DQPe
DQe
DQe
DQe
DQe
VSS
VSS
NC
A
MODE
A
U
V
W
NC/72M
A
NC/288M
NC/144M
A
A
A1
A
DQd
DQd
A
A
A
A
DQe
DQe
TDI
TDO
TCK
A0
A
TMS
Document #: 38-05356 Rev. *F
Page 7 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Pin Definitions
Name
IO
Description
Address Inputs used to select one of the address locations. Sampled at the rising edge of the
A0, A1, A
Input-
Synchronous CLK. A[1:0] are fed to the two-bit burst counter.
BWA, BWB
Input- Byte Write Inputs, Active LOW. Qualified with WE to conduct writes to the SRAM. Sampled on
BWC, BWD, Synchronous the rising edge of CLK.
BWE, BWF,
BWG, BWH
WE
Input-
Write Enable Input, Active LOW. Sampled on the rising edge of CLK if CEN is active LOW. This
Synchronous signal must be asserted LOW to initiate a write sequence.
ADV/LD
Input- Advance/Load Input. Used to advance the on-chip address counter or load a new address. When
Synchronous HIGH (and CEN is asserted LOW) the internal burst counter is advanced. When LOW, a new
address can be loaded into the device for an access. After being deselected, ADV/LD must be
driven LOW to load a new address.
CLK
CE1
CE2
CE3
OE
Input-
Clock
Clock Input. Used to capture all synchronous inputs to the device. CLK is qualified with CEN. CLK
is only recognized if CEN is active LOW.
Input-
Chip Enable 1 Input, Active LOW. Sampled on the rising edge of CLK. Used in conjunction with
Synchronous CE2 and CE3 to select/deselect the device.
Input-
Chip Enable 2 Input, Active HIGH. Sampled on the rising edge of CLK. Used in conjunction with
Synchronous CE1 and CE3 to select/deselect the device.
Input-
Chip Enable 3 Input, Active LOW. Sampled on the rising edge of CLK. Used in conjunction with
Synchronous CE1 and CE2 to select/deselect the device.
Input-
Output Enable, asynchronous input, Active LOW. Combined with the synchronous logic block
Asynchronous inside the device to control the direction of the IO pins. When LOW, the IO pins are allowed to
behave as outputs. When deasserted HIGH, IO pins are tri-stated, and act as input data pins. OE
is masked during the data portion of a write sequence, during the first clock when emerging from
a deselected state, when the device is deselected.
CEN
ZZ
Input-
Clock Enable Input, Active LOW. When asserted LOW the Clock signal is recognized by the
Synchronous SRAM. When deasserted HIGH the Clock signal is masked. Since deasserting CEN does not
deselect the device, use CEN to extend the previous cycle when required.
Input-
ZZ “Sleep” Input. This active HIGH input places the device in a non-time critical “sleep” condition
Asynchronous with data integrity preserved. During normal operation, this pin has to be LOW or left floating. ZZ
pin has an internal pull down.
IO-
Bidirectional Data IO lines. As inputs, they feed into an on-chip data register that is triggered by
DQs
Synchronous the rising edge of CLK. As outputs, they deliver the data contained in the memory location specified
by the addresses presented during the previous clock rise of the read cycle. The direction of the
pins is controlled by OE. When OE is asserted LOW, the pins behave as outputs. When HIGH,
DQs and DQP[A:D] are placed in a tri-state condition.The outputs are automatically tri-stated during
the data portion of a write sequence, during the first clock when emerging from a deselected state,
and when the device is deselected, regardless of the state of OE.
IO-
Bidirectional Data Parity IO Lines. Functionally, these signals are identical to DQs. During write
DQPX
Synchronous sequences, DQPX is controlled by BWX correspondingly.
MODE
Input Strap Pin Mode Input. Selects the burst order of the device.
When tied to Gnd selects linear burst sequence. When tied to VDD or left floating selects interleaved
burst sequence.
VDD
Power Supply Power supply inputs to the core of the device.
VDDQ
IO Power
Supply
Power supply for the IO circuitry.
VSS
Ground
Ground for the device.
Document #: 38-05356 Rev. *F
Page 8 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Pin Definitions (continued)
Name
TDO
IO
Description
JTAG serial Serial data-out to the JTAG circuit. Delivers data on the negative edge of TCK. If the JTAG
output
feature is not used, leave this pin unconnected. This pin is not available on TQFP packages.
Synchronous
TDI
JTAG serial Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG feature is not
input being used, this pin can be left floating or connected to VDD through a pull up resistor. This pin is
Synchronous not available on TQFP packages.
TMS
TCK
JTAG serial Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG feature is not
input
being used, this pin can be disconnected or connected to VDD. This pin is not available on TQFP
Synchronous packages.
JTAG-Clock Clock input to the JTAG circuitry. If the JTAG feature is not being used, this pin must be
connected to VSS. This pin is not available on TQFP packages.
NC
N/A
N/A
N/A
N/A
N/A
N/A
No Connects. Not internally connected to the die.
NC/72M
NC/144M
NC/288M
NC/576M
NC/1G
Not connected to the die. Can be tied to any voltage level.
Not connected to the die. Can be tied to any voltage level.
Not connected to the die. Can be tied to any voltage level.
Not connected to the die. Can be tied to any voltage level.
Not connected to the die. Can be tied to any voltage level.
• CE1, CE2, and CE3 are ALL asserted active
Functional Overview
• The Write Enable input signal WE is deasserted HIGH
• ADV/LD is asserted LOW.
The CY7C1461AV33/CY7C1463AV33/CY7C1465AV33 is a
synchronous flow through burst SRAM designed specifically
to eliminate wait states during Write-Read transitions. All
synchronous inputs pass through input registers controlled by
the rising edge of the clock. The clock signal is qualified with
the Clock Enable input signal (CEN). If CEN is HIGH, the clock
signal is not recognized and all internal states are maintained.
All synchronous operations are qualified with CEN. Maximum
access delay from the clock rise (tCDV) is 6.5 ns (133-MHz
device).
The address presented to the address inputs is latched into
the Address Register and presented to the memory array and
control logic. The control logic determines that a read access
is in progress and allows the requested data to propagate to
the output buffers. The data is available within 6.5 ns
(133-MHz device) provided OE is active LOW. After the first
clock of the read access, the output buffers are controlled by
OE and the internal control logic. OE must be driven LOW in
order for the device to drive out the requested data. On the
subsequent clock, another operation (Read/Write/Deselect)
can be initiated. When the SRAM is deselected at clock rise
by one of the chip enable signals, its output is tri-stated
immediately.
Accesses can be initiated by asserting all three Chip Enables
(CE1, CE2, CE3) active at the rising edge of the clock. If Clock
Enable (CEN) is active LOW and ADV/LD is asserted LOW,
the address presented to the device is latched. The access
can either be a read or write operation, depending on the
status of the Write Enable (WE). BWX can be used to conduct
byte write operations.
Burst Read Accesses
The CY7C1461AV33/CY7C1463AV33/CY7C1465AV33 has
an on-chip burst counter that allows the user the ability to
supply a single address and conduct up to four Reads without
reasserting the address inputs. ADV/LD must be driven LOW
to load a new address into the SRAM, as described in the
Single Read Access section above. The sequence of the burst
counter is determined by the MODE input signal. A LOW input
on MODE selects a linear burst mode, a HIGH selects an inter-
leaved burst sequence. Both burst counters use A0 and A1 in
the burst sequence, and wraps around when incremented
sufficiently. A HIGH input on ADV/LD increments the internal
burst counter regardless of the state of chip enable inputs or
WE. WE is latched at the beginning of a burst cycle. Therefore,
the type of access (Read or Write) is maintained throughout
the burst sequence.
Write operations are qualified by the Write Enable (WE). All
writes are simplified with on-chip synchronous self timed write
circuitry.
Three synchronous Chip Enables (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) simplify depth expansion.
All operations (Reads, Writes, and Deselects) are pipelined.
ADV/LD must be driven LOW after the device has been
deselected to load a new address for the next operation.
Single Read Accesses
A read access is initiated when these conditions are satisfied
at clock rise:
• CEN is asserted LOW
Document #: 38-05356 Rev. *F
Page 9 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Single Write Accesses
HIGH on the subsequent clock rise, the Chip Enables (CE1,
CE2, and CE3) and WE inputs are ignored and the burst
counter is incremented. The correct BWX inputs must be
driven in each cycle of the burst write, to write the correct bytes
Write access are initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are ALL asserted active, and (3) the write signal WE
is asserted LOW. The address presented to the address bus
is loaded into the Address Register. The write signals are
latched into the Control Logic block. The data lines are
automatically tri-stated regardless of the state of the OE input
signal. This allows the external logic to present the data on
DQs and DQPX.
of data.
.
Interleaved Burst Address Table
(MODE = Floating or VDD
)
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
On the next clock rise the data presented to DQs and DQPX
(or a subset for byte write operations, see truth table for
details) inputs is latched into the device and the write is
complete. Additional accesses (Read/Write/Deselect) can be
initiated on this cycle.
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
The data written during the Write operation is controlled by
BWX signals. The CY7C1461AV33/CY7C1463AV33/CY7C1465AV33
provides byte write capability that is described in the truth
table. Asserting the Write Enable input (WE) with the selected
Byte Write Select input selectively writes to only the desired
bytes. Bytes not selected during a byte write operation
remains unaltered. A synchronous self timed write mechanism
has been provided to simplify the write operations. Byte write
capability has been included to greatly simplify
Read/Modify/Write sequences, which can be reduced to
simple byte write operations.
Linear Burst Address Table (MODE = GND)
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
Because the CY7C1461AV33/CY7C1463AV33/CY7C1465AV33
isa common IO device, data must not be driven into the device
while the outputs are active. The Output Enable (OE) can be
deasserted HIGH before presenting data to the DQs and
DQPX inputs. Doing so tri-states the output drivers. As a safety
precaution, DQs and DQPX are automatically tri-stated during
the data portion of a write cycle, regardless of the state of OE.
Sleep Mode
The ZZ input pin is an asynchronous input. Asserting ZZ
places the SRAM in a power conservation “sleep” mode. Two
clock cycles are required to enter into or exit from this “sleep”
mode. While in this mode, data integrity is guaranteed.
Accesses pending when entering the “sleep” mode are not
considered valid nor is the completion of the operation
guaranteed. The device must be deselected prior to entering
the “sleep” mode. CE1, CE2, and CE3, must remain inactive
for the duration of tZZREC after the ZZ input returns LOW.
Burst Write Accesses
The CY7C1461AV33/CY7C1463AV33/CY7C1465AV33 has
an on-chip burst counter that allows the user the ability to
supply a single address and conduct up to four Write opera-
tions without reasserting the address inputs. ADV/LD must be
driven LOW to load the initial address, as described in the
Single Write Access section above. When ADV/LD is driven
ZZ Mode Electrical Characteristics
Parameter
IDDZZ
Description
Sleep mode standby current
Device operation to ZZ
Test Conditions
ZZ > VDD – 0.2V
Min
Max
100
Unit
mA
ns
tZZS
ZZ > VDD – 0.2V
2tCYC
tZZREC
tZZI
ZZ recovery time
ZZ < 0.2V
2tCYC
ns
ZZ active to sleep current
ZZ Inactive to exit sleep current
This parameter is sampled
This parameter is sampled
2tCYC
ns
tRZZI
0
ns
Document #: 38-05356 Rev. *F
Page 10 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Truth Table[2, 3, 4, 5, 6, 7, 8]
Address
Used
Operation
Deselect Cycle
CE1 CE2
ZZ ADV/LD WE BWX OE CEN CLK
DQ
CE3
X
None
None
H
X
X
X
L
X
X
L
L
L
L
L
L
L
L
L
H
L
X
X
X
X
H
X
X
X
X
X
X
X
X
X
L
L
L
L
L
L
L->H Tri-State
L->H Tri-State
L->H Tri-State
L->H Tri-State
Deselect Cycle
H
Deselect Cycle
None
X
Continue Deselect Cycle
Read Cycle (Begin Burst)
None
X
H
X
External
L
L->H Data Out
(Q)
Read Cycle (Continue Burst)
Next
X
L
X
H
X
L
L
L
H
L
X
H
X
X
L
L
L
L->H Data Out
(Q)
NOP/Dummy Read
(Begin Burst)
External
H
L->H Tri-State
Dummy Read (Continue Burst)
Write Cycle (Begin Burst)
Write Cycle (Continue Burst)
NOP/Write Abort (Begin Burst)
Write Abort (Continue Burst)
Ignore Clock Edge (Stall)
Sleep Mode
Next
External
Next
X
L
X
H
X
H
X
X
X
X
L
L
L
L
L
L
L
H
H
L
X
L
X
L
H
X
X
X
X
X
X
L
L
L
L
L
H
X
L->H Tri-State
L->H Data In (D)
L->H Data In (D)
L->H Tri-State
L->H Tri-State
X
L
X
L
H
L
X
L
L
None
H
H
X
X
Next
X
X
X
X
X
X
H
X
X
X
X
X
Current
None
L->H
X
–
Tri-State
Notes:
2. X = “Don't Care.” H = Logic HIGH, L = Logic LOW. BWx = L signifies at least one Byte Write Select is active, BWx = Valid signifies that the desired byte write
selects are asserted, see truth table for details.
3. Write is defined by BW , and WE. See truth table for Read/Write.
X
4. When a write cycle is detected, all IOs are tri-stated, even during byte writes.
5. The DQs and DQP pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock.
X
6. CEN = H, inserts wait states.
7. Device powers up deselected and the IOs in a tri-state condition, regardless of OE.
8. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle DQs and DQP = Tri-state when OE
X
is inactive or when the device is deselected, and DQs and DQP = data when OE is active.
X
Document #: 38-05356 Rev. *F
Page 11 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Truth Table for Read/Write[2, 9]
Function (CY7C1461AV33)
Read
WE
H
L
BWA
X
BWB
X
BWC
X
BWD
X
Write No bytes written
H
H
H
H
Write Byte A – (DQA and DQPA)
Write Byte B – (DQB and DQPB)
Write Byte C – (DQC and DQPC)
Write Byte D – (DQD and DQPD)
Write All Bytes
L
L
H
H
H
L
H
L
H
H
L
H
H
L
H
L
H
H
H
L
L
L
L
L
L
Truth Table for Read/Write[2, 9]
Function (CY7C1463AV33)
Read
WE
H
L
BWb
X
BWa
X
Write – No Bytes Written
Write Byte a – (DQa and DQPa)
Write Byte b – (DQb and DQPb)
Write Both Bytes
H
H
L
H
L
L
L
H
L
L
L
Truth Table for Read/Write[2, 9]
Function (CY7C1465AV33)
Read
WE
H
BWx
X
Write – No Bytes Written
Write Byte X − (DQx and DQPx)
Write All Bytes
L
H
L
L
L
All BW = L
Note:
9. Table only lists a partial listing of the byte write combinations. Any Combination of BW is valid Appropriate write is done based on which byte write is active
X
Document #: 38-05356 Rev. *F
Page 12 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Test Data In (TDI)
IEEE 1149.1 Serial Boundary Scan (JTAG)
The TDI ball is used to serially input information into the
registers and can be connected to the input of any of the
registers. The register between TDI and TDO is chosen by the
instruction that is loaded into the TAP instruction register. TDI
is internally pulled up and can be unconnected if the TAP is
unused in an application. TDI is connected to the most signif-
icant bit (MSB) of any register. (See Tap Controller Block
Diagram.)
The CY7C1461AV33/CY7C1463AV33/CY7C1465AV33 incor-
porates a serial boundary scan test access port (TAP). This
part is fully compliant with 1149.1. The TAP operates using
JEDEC-standard 3.3V/2.5V IO logic level.
The CY7C1461AV33/CY7C1463AV33/CY7C1465AV33 contains
a TAP controller, instruction register, boundary scan register,
bypass register, and ID register.
Disabling the JTAG Feature
Test Data Out (TDO)
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(VSS) to prevent clocking of the device. TDI and TMS are inter-
nally pulled up and may be unconnected. They may alternately
be connected to VDD through a pull up resistor. TDO must be
left unconnected. Upon power up, the device is up in a reset
state which does not interfere with the operation of the device.
The TDO output ball is used to serially clock data-out from the
registers. The output is active depending upon the current
state of the TAP state machine. The output changes on the
falling edge of TCK. TDO is connected to the least significant
bit (LSB) of any register. (See Tap Controller State Diagram.)
TAP Controller Block Diagram
TAP Controller State Diagram
0
Bypass Register
TEST-LOGIC
1
RESET
0
2
1
0
0
0
Selection
Circuitry
Selection
Circuitry
1
1
1
Instruction Register
31 30 29
Identification Register
RUN-TEST/
IDLE
SELECT
DR-SCAN
SELECT
IR-SCAN
0
TDI
TDO
.
.
. 2 1
0
0
1
1
CAPTURE-DR
CAPTURE-IR
0
0
x
.
.
.
.
. 2 1
SHIFT-DR
0
SHIFT-IR
0
Boundary Scan Register
1
1
1
1
EXIT1-DR
EXIT1-IR
TCK
TMS
0
0
TAP CONTROLLER
PAUSE-DR
1
0
PAUSE-IR
1
0
0
0
EXIT2-DR
1
EXIT2-IR
1
Performing a TAP Reset
A RESET is performed by forcing TMS HIGH (VDD) for five
rising edges of TCK. This RESET does not affect the operation
of the SRAM and may be performed while the SRAM is
operating.
UPDATE-DR
UPDATE-IR
1
0
1
0
At power up, the TAP is reset internally to ensure that TDO
comes up in a High-Z state.
The 0/1 next to each state represents the value of TMS at the
rising edge of TCK.
TAP Registers
Registers are connected between the TDI and TDO balls and
allow data to be scanned into and out of the SRAM test
circuitry. Only one register can be selected at a time through
the instruction register. Data is serially loaded into the TDI ball
on the rising edge of TCK. Data is output on the TDO ball on
the falling edge of TCK.
Test Access Port (TAP)
Test Clock (TCK)
The test clock is used only with the TAP controller. All inputs
are captured on the rising edge of TCK. All outputs are driven
from the falling edge of TCK.
Instruction Register
Test Mode Select (TMS)
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the
TDI and TDO balls as shown in the Tap Controller Block
Diagram. Upon power up, the instruction register is loaded
with the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state as
described in the previous section.
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. It is allowable to
leave this ball unconnected if the TAP is not used. The ball is
pulled up internally, resulting in a logic HIGH level.
Document #: 38-05356 Rev. *F
Page 13 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
When the TAP controller is in the Capture-IR state, the two
least significant bits are loaded with a binary “01” pattern to
allow for fault isolation of the board-level serial test data path.
The IDCODE instruction is loaded into the instruction register
upon power up or whenever the TAP controller is supplied a
test logic reset state.
Bypass Register
SAMPLE Z
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between the
TDI and TDO balls. This allows data to be shifted through the
SRAM with minimal delay. The bypass register is set LOW
(VSS) when the BYPASS instruction is executed.
The SAMPLE Z instruction causes the boundary scan register
to be connected between the TDI and TDO pins when the TAP
controller is in a Shift-DR state. The SAMPLE Z command puts
the output bus into a High-Z state until the next command is
supplied during the “Update IR” state.
SAMPLE/PRELOAD
Boundary Scan Register
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the inputs and output pins is
captured in the boundary scan register.
The boundary scan register is connected to all the input and
bidirectional balls on the SRAM. The length of the Boundary
Scan Register for the SRAM in different packages is listed in
the Scan Register Sizes table.
The boundary scan register is loaded with the contents of the
RAM IO ring when the TAP controller is in the Capture-DR
state and is then placed between the TDI and TDO balls when
the controller is moved to the Shift-DR state. The EXTEST,
SAMPLE/PRELOAD and SAMPLE Z instructions can be used
to capture the contents of the IO ring.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 20 MHz, while the SRAM clock
operates more than an order of magnitude faster. Because
there is a large difference in the clock frequencies, it is
possible that during the Capture-DR state, an input or output
undergoes a transition. The TAP may then try to capture a
signal while in transition (metastable state). This does not
harm the device, but there is no guarantee as to the value that
is captured. Repeatable results may not be possible.
The Boundary Scan Order tables show the order in which the
bits are connected. Each bit corresponds to one of the bumps
on the SRAM package. The MSB of the register is connected
to TDI, and the LSB is connected to TDO.
To guarantee that the boundary scan register captures the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller's capture setup plus
hold times (tCS and tCH). The SRAM clock input might not be
captured correctly if there is no way in a design to stop (or
slow) the clock during a SAMPLE/PRELOAD instruction. If this
is an issue, it is still possible to capture all other signals and
simply ignore the value of the CK and CK captured in the
boundary scan register.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired
into the SRAM and can be shifted out when the TAP controller
is in the Shift-DR state. The ID register has a vendor code and
other information described in the Identification Register
Definitions table.
Once the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the
boundary scan register between the TDI and TDO pins.
TAP Instruction Set
Overview
PRELOAD allows an initial data pattern to be placed at the
latched parallel outputs of the boundary scan register cells
prior to the selection of another boundary scan test operation.
Eight different instructions are possible with the three bit
instruction register. All combinations are listed in the
Instruction Codes table. Three of these instructions are listed
as RESERVED and must not be used. The other five instruc-
tions are described in detail below.
The shifting of data for the SAMPLE and PRELOAD phases
can occur concurrently when required—that is, while data
captured is shifted out, the preloaded data can be shifted in.
Instructions are loaded into the TAP controller during the
Shift-IR state when the instruction register is placed between
TDI and TDO. During this state, instructions are shifted
through the instruction register through the TDI and TDO balls.
To execute the instruction after it is shifted in, the TAP
controller needs to be moved into the Update-IR state.
BYPASS
When the BYPASS instruction is loaded in the instruction
register and the TAP is placed in a Shift-DR state, the bypass
register is placed between the TDI and TDO pins. The
advantage of the BYPASS instruction is that it shortens the
boundary scan path when multiple devices are connected
together on a board.
IDCODE
The IDCODE instruction causes a vendor-specific, 32-bit code
to be loaded into the instruction register. It also places the
instruction register between the TDI and TDO balls and allows
the IDCODE to be shifted out of the device when the TAP
controller enters the Shift-DR state.
EXTEST
The EXTEST instruction enables the preloaded data to be
driven out through the system output pins. This instruction also
selects the boundary scan register to be connected for serial
access between the TDI and TDO in the shift-DR controller
state.
Document #: 38-05356 Rev. *F
Page 14 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
EXTEST OUTPUT BUS TRI-STATE
This bit can be set by entering the SAMPLE/PRELOAD or
EXTEST command, and then shifting the desired bit into that
cell, during the “Shift-DR” state. During “Update-DR”, the value
loaded into that shift-register cell latches into the preload
register. When the EXTEST instruction is entered, this bit
directly controls the output Q-bus pins. Note that this bit is
pre-set HIGH to enable the output when the device is
powered-up, and also when the TAP controller is in the
“Test-Logic-Reset” state.
IEEE Standard 1149.1 mandates that the TAP controller be
able to put the output bus into a tri-state mode.
The boundary scan register has a special bit located at bit #89
(for 165-FBGA package) or bit #138 (for 209 FBGA package).
When this scan cell, called the “extest output bus tri-state”, is
latched into the preload register during the “Update-DR” state
in the TAP controller, it directly controls the state of the output
(Q-bus) pins, when the EXTEST is entered as the current
instruction. When HIGH, it enables the output buffers to drive
the output bus. When LOW, this bit places the output bus into
a High-Z condition.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
TAP Timing
1
2
3
4
5
6
Test Clock
(TCK)
t
t
t
CYC
TH
TL
t
t
t
t
TMSS
TDIS
TMSH
Test Mode Select
(TMS)
TDIH
Test Data-In
(TDI)
t
TDOV
t
TDOX
Test Data-Out
(TDO)
DON’T CARE
UNDEFINED
Document #: 38-05356 Rev. *F
Page 15 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
TAP AC Switching Characteristics
Over the Operating Range[10, 11]
Parameter
Clock
Description
Min
Max
Unit
tTCYC
TCK Clock Cycle Time
TCK Clock Frequency
TCK Clock HIGH time
TCK Clock LOW time
50
ns
MHz
ns
tTF
20
tTH
20
20
tTL
ns
Output Times
tTDOV
tTDOX
Setup Times
tTMSS
tTDIS
TCK Clock LOW to TDO Valid
TCK Clock LOW to TDO Invalid
10
ns
ns
0
TMS Setup to TCK Clock Rise
TDI Setup to TCK Clock Rise
Capture Setup to TCK Rise
5
5
5
ns
ns
ns
tCS
Hold Times
tTMSH
tTDIH
TMS Hold after TCK Clock Rise
TDI Hold after Clock Rise
5
5
5
ns
ns
ns
tCH
Capture Hold after Clock Rise
Notes:
10. t and t refer to the setup and hold time requirements of latching data from the boundary scan register.
CS
CH
11. Test conditions are specified using the load in TAP AC test Conditions. t /t = 1 ns.
R
F
Document #: 38-05356 Rev. *F
Page 16 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
3.3V TAP AC Test Conditions
2.5V TAP AC Test Conditions
Input pulse levels ................................................ VSS to 3.3V
Input rise and fall times................................................... 1 ns
Input timing reference levels...........................................1.5V
Output reference levels...................................................1.5V
Test load termination supply voltage...............................1.5V
Input pulse levels.................................................VSS to 2.5V
Input rise and fall time .....................................................1 ns
Input timing reference levels......................................... 1.25V
Output reference levels ............................................... .1.25V
Test load termination supply voltage ............................ 1.25V
3.3V TAP AC Output Load Equivalent
2.5V TAP AC Output Load Equivalent
1.25V
1.5V
50Ω
50Ω
TDO
TDO
ZO= 50Ω
20pF
ZO= 50Ω
20pF
TAP DC Electrical Characteristics And Operating Conditions
(0°C < TA < +70°C; VDD = 3.135 to 3.6V unless otherwise noted)[12]
Parameter
VOH1
Description
Test Conditions
IOH = –4.0 mA, VDDQ = 3.3V
IOH = –1.0 mA, VDDQ = 2.5V
IOH = –100 µA
Min
Max
Unit
V
Output HIGH Voltage
2.4
2.0
2.9
2.1
V
VOH2
VOL1
VOL2
VIH
Output HIGH Voltage
Output LOW Voltage
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
Input Load Current
VDDQ = 3.3V
VDDQ = 2.5V
VDDQ = 3.3V
VDDQ = 2.5V
VDDQ = 3.3V
VDDQ = 2.5V
VDDQ = 3.3V
VDDQ = 2.5V
VDDQ = 3.3V
V
V
IOL = 8.0 mA
0.4
0.4
V
IOL = 1.0 mA
V
IOL = 100 µA
0.2
V
0.2
V
2.0
1.7
VDD + 0.3
VDD + 0.3
0.8
V
V
VIL
–0.3
–0.3
–5
V
V
DDQ = 2.5V
0.7
V
IX
GND < VIN < VDDQ
5
µA
Note:
12. All voltages referenced to V (GND).
SS
Document #: 38-05356 Rev. *F
Page 17 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Identification Register Definitions
CY7C1461AV33 CY7C1463AV33 CY7C1465AV33
Instruction Field
Revision Number (31:29)
Device Depth (28:24)[13]
(1M x 36)
(2M x 18)
(512K x 72)
Description
000
000
000
Describes the version number
Reserved for internal use
01011
01011
01011
Architecture/Memory Type (23:18)
001001
001001
001001
Defines memory type and
architecture
Bus Width/Density(17:12)
100111
010111
110111
Defines width and density
Cypress JEDEC ID Code (11:1)
00000110100
00000110100
00000110100 Allows unique identification of
SRAM vendor
ID Register Presence Indicator (0)
1
1
1
Indicates the presence of an ID
register
Scan Register Sizes
Register Name
Bit Size (x36)
Bit Size (x18)
Bit Size (x72)
Instruction
Bypass
ID
3
1
3
1
3
1
32
89
–
32
89
–
32
–
Boundary Scan Order (165-Ball FBGA package)
Boundary Scan Order (209-Ball FBGA package)
138
Identification Codes
Instruction
EXTEST
Code
Description
000
Captures IO ring contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM outputs to High-Z state.
IDCODE
001
010
Loads the ID register with the vendor ID code and places the register between TDI and
TDO. This operation does not affect SRAM operations.
SAMPLE Z
Captures IO ring contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM output drivers to a High-Z state.
RESERVED
011
100
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
Captures IO ring contents. Places the boundary scan register between TDI and TDO.
Does not affect SRAM operation.
RESERVED
RESERVED
BYPASS
101
110
111
Do Not Use: This instruction is reserved for future use.
Do Not Use: This instruction is reserved for future use.
Places the bypass register between TDI and TDO. This operation does not affect SRAM
operations.
Note:
13. Bit #24 is “1” in the ID Register Definitions for both 2.5V and 3.3V versions of this device.
Document #: 38-05356 Rev. *F
Page 18 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
165-Ball FBGA Boundary Scan Order [14]
CY7C1461AV33 (1M x 36), CY7C1463AV33 (2M x 18)
Bit#
1
Ball ID
N6
Bit#
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Ball ID
E11
D11
G10
F10
E10
D10
C11
A11
B11
A10
B10
A9
Bit#
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
Ball ID
A3
A2
B2
C2
B1
A1
C1
D1
E1
F1
Bit#
76
77
78
79
80
81
82
83
84
85
86
87
88
89
Ball ID
N1
2
N7
N2
3
N10
P11
P8
P1
4
R1
5
R2
6
R8
P3
7
R9
R3
8
P9
P2
9
P10
R10
R11
H11
N11
M11
L11
K11
J11
M10
L10
K10
J10
H9
R4
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
P4
G1
D2
E2
F2
N5
P6
B9
R6
C10
A8
Internal
G2
H1
H3
J1
B8
A7
B7
B6
K1
L1
A6
B5
M1
J2
A5
H10
G11
F11
A4
K2
L2
B4
B3
M2
Note:
14. Bit# 89 is preset HIGH.
Document #: 38-05356 Rev. *F
Page 19 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
209-Ball FBGA Boundary Scan Order [15]
CY7C1465AV33 (512K x 72)
Bit#
1
Ball ID
W6
V6
Bit#
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
Ball ID
F6
Bit#
71
Ball ID
H6
C6
B6
A6
A5
B5
C5
D5
D4
C4
A4
B4
C3
B3
A3
A2
A1
B2
B1
C2
C1
D2
D1
E1
E2
F2
Bit#
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
Ball ID
K3
2
K8
72
K4
3
U6
K9
73
K6
4
W7
V7
K10
J11
J10
H11
H10
G11
G10
F11
F10
E10
E11
D11
D10
C11
C10
B11
B10
A11
A10
C9
74
K2
5
75
L2
6
U7
76
L1
7
T7
77
M2
M1
N2
N1
P2
8
V8
78
9
U8
79
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
T8
80
V9
81
U9
82
P1
P6
83
R2
R1
T2
W11
W10
V11
V10
U11
U10
T11
T10
R11
R10
P11
P10
N11
N10
M11
M10
L11
L10
K11
M6
84
85
86
T1
87
U2
U1
V2
88
89
90
V1
91
W2
W1
T6
92
93
B9
94
U3
V3
A9
95
D8
96
T4
C8
97
F1
T5
B8
98
G1
G2
H2
H1
J2
U4
V4
A8
99
D7
100
101
102
103
104
105
W5
V5
C7
B7
U5
Internal
A7
J1
L6
D6
K1
N6
J6
G6
Note:
15. Bit# 138 is preset HIGH.
Document #: 38-05356 Rev. *F
Page 20 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
DC Input Voltage ................................... –0.5V to VDD + 0.5V
Current into Outputs (LOW)......................................... 20 mA
Maximum Ratings
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Static Discharge Voltage........................................... >2001V
(MIL-STD-883, Method 3015)
Storage Temperature .................................–65°C to +150°C
Latch-up Current..................................................... >200 mA
Ambient Temperature with
Power Applied.............................................–55°C to +125°C
Operating Range
Supply Voltage on VDD Relative to GND........ –0.5V to +4.6V
Supply Voltage on VDDQ Relative to GND ......–0.5V to +VDD
Ambient
Temperature
Range
VDD
VDDQ
Commercial 0°C to +70°C
Industrial –40°C to +85°C
3.3V –5%/+10% 2.5V – 5%
to VDD
DC Voltage Applied to Outputs
in Tri-State........................................... –0.5V to VDDQ + 0.5V
Electrical Characteristics
Over the Operating Range[16, 17]
Parameter
VDD
Description
Power Supply Voltage
IO Supply Voltage
Test Conditions
Min
3.135
3.135
2.375
2.4
Max
3.6
Unit
V
VDDQ
for 3.3V IO
for 2.5V IO
VDD
2.625
V
V
VOH
VOL
VIH
VIL
IX
Output HIGH Voltage
Output LOW Voltage
for 3.3V IO, IOH = –4.0 mA
for 2.5V IO, IOH = –1.0 mA
for 3.3V IO, IOL = 8.0 mA
for 2.5V IO, IOL = 1.0 mA
V
2.0
V
0.4
0.4
V
V
Input HIGH Voltage[16] for 3.3V IO
2.0
1.7
VDD + 0.3V
VDD + 0.3V
0.8
V
for 2.5V IO
V
Input LOW Voltage[16]
for 3.3V IO
for 2.5V IO
–0.3
–0.3
–5
V
0.7
V
Input Leakage Current GND ≤ VI ≤ VDDQ
except ZZ and MODE
5
µA
Input Current of MODE Input = VSS
Input = VDD
–30
–5
µA
µA
µA
µA
µA
5
Input Current of ZZ
Input = VSS
Input = VDD
30
5
IOZ
IDD
Output Leakage Current GND ≤ VI ≤ VDDQ, Output Disabled
–5
VDD Operating Supply VDD = Max., IOUT = 0 mA,
7.5 ns cycle, 133 MHz
10 ns cycle, 100 MHz
310
290
180
180
mA
mA
mA
mA
Current
f = fMAX = 1/tCYC
ISB1
ISB2
ISB3
ISB4
Automatic CE
Power down
Current—TTL Inputs
VDD = Max, Device Deselected, 7.5 ns cycle, 133 MHz
VIN ≥ VIH or VIN ≤ VIL
f = fMAX, inputs switching
10 ns cycle, 100 MHz
Automatic CE
Power down
Current—CMOS Inputs f = 0, inputs static
V
DD = Max, Device Deselected, All speeds
120
mA
VIN ≤ 0.3V or VIN > VDD – 0.3V,
Automatic CE
Power down
Current—CMOS Inputs f = fMAX, inputs switching
V
DD = Max, Device Deselected, 7.5 ns cycle, 133 MHz
180
180
mA
mA
or VIN ≤ 0.3V or VIN > VDDQ – 0.3V
10 ns cycle, 100 MHz
Automatic CE
VDD = Max, Device Deselected, All Speeds
135
mA
Power down
Current—TTL Inputs
VIN ≥ VDD – 0.3V or VIN ≤ 0.3V,
f = 0, inputs static
Notes:
16. Overshoot: V (AC) < V +1.5V (Pulse width less than t
/2), undershoot: V (AC) > –2V (Pulse width less than t
/2).
CYC
IH
DD
CYC
IL
17. T
: Assumes a linear ramp from 0V to V (min.) within 200 ms. During this time V < V and V
< V
.
Power-up
DD
IH
DD
DDQ
DD
Document #: 38-05356 Rev. *F
Page 21 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Capacitance[18]
100 TQFP 165 FBGA 209 FBGA
Parameter
Description
Test Conditions
Max
6.5
3
Max
Max
Unit
pF
CIN
Input Capacitance
TA = 25°C, f = 1 MHz,
7
7
6
5
5
7
VDD = 3.3V
CCLK
CIO
Clock Input Capacitance
Input/Output Capacitance
pF
VDDQ = 2.5V
5.5
pF
Thermal Resistance[18]
100 TQFP 165 FBGA 209 FBGA
Unit
Parameter
Description
Test Conditions
Package
Package
Package
ΘJA
Thermal Resistance
(Junction to Ambient)
Test conditions follow standard
test methods and procedures
for measuring thermal
impedance, according to
EIA/JESD51.
25.21
20.8
25.31
°C/W
ΘJC
Thermal Resistance
(Junction to Case)
2.28
3.2
4.48
°C/W
AC Test Loads and Waveforms
3.3V IO Test Load
R = 317Ω
3.3V
OUTPUT
ALL INPUT PULSES
90%
VDDQ
GND
OUTPUT
90%
10%
Z = 50Ω
0
R = 50Ω
10%
L
5 pF
R = 351Ω
INCLUDING
JIG AND
SCOPE
≤ 1ns
≤ 1ns
V = 1.5V
T
(a)
(b)
(c)
2.5V IO Test Load
R = 1667Ω
2.5V
OUTPUT
R = 50Ω
OUTPUT
ALL INPUT PULSES
90%
VDDQ
GND
90%
10%
Z = 50Ω
0
10%
L
5 pF
R = 1538Ω
INCLUDING
JIG AND
SCOPE
≤ 1ns
≤ 1ns
V = 1.25V
T
(a)
(b)
(c)
Note:
18. Tested initially and after any design or process change that may affect these parameters.
Document #: 38-05356 Rev. *F
Page 22 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Switching Characteristics
Over the Operating Range[23, 24]
133 MHz
100 MHz
Parameter
Description
Min Max Min Max Unit
[19]
tPOWER
1
1
ms
Clock
tCYC
tCH
tCL
Clock Cycle Time
Clock HIGH
7.5
2.5
2.5
10
3.0
3.0
ns
ns
ns
Clock LOW
Output Times
tCDV
Data Output Valid After CLK Rise
6.5
8.5
ns
ns
ns
ns
ns
ns
ns
tDOH
Data Output Hold After CLK Rise
Clock to Low-Z[20, 21, 22]
2.5
2.5
2.5
2.5
0
tCLZ
tCHZ
Clock to High-Z[20, 21, 22]
3.8
3.0
4.5
3.8
tOEV
OE LOW to Output Valid
tOELZ
tOEHZ
Setup Times
tAS
OE LOW to Output Low-Z[20, 21, 22]
OE HIGH to Output High-Z[20, 21, 22]
0
0
3.0
4.0
Address Setup Before CLK Rise
ADV/LD Setup Before CLK Rise
WE, BWX Setup Before CLK Rise
CEN Setup Before CLK Rise
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
ns
ns
ns
ns
ns
ns
tALS
tWES
tCENS
tDS
Data Input Setup Before CLK Rise
Chip Enable Setup Before CLK Rise
tCES
Hold Times
tAH
Address Hold After CLK Rise
ADV/LD Hold After CLK Rise
WE, BWX Hold After CLK Rise
CEN Hold After CLK Rise
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
ns
ns
ns
ns
ns
ns
tALH
tWEH
tCENH
tDH
Data Input Hold After CLK Rise
Chip Enable Hold After CLK Rise
tCEH
Notes:
19. This part has a voltage regulator internally; t
is the time that the power needs to be supplied above V (minimum) initially, before a read or write operation
DD
POWER
can be initiated.
20. t
, t
,t
, and t
are specified with AC test conditions shown in part (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage.
CHZ CLZ OELZ
OEHZ
21. At any voltage and temperature, t
is less than t
and t
is less than t
to eliminate bus contention between SRAMs when sharing the same data bus.
CLZ
OEHZ
OELZ
CHZ
These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to achieve
High-Z prior to Low-Z under the same system conditions.
22. This parameter is sampled and not 100% tested.
23. Timing reference level is 1.5V when V
= 3.3V and is 1.25V when V
= 2.5V.
DDQ
DDQ
24. Test conditions shown in (a) of AC Test Loads unless otherwise noted.
Document #: 38-05356 Rev. *F
Page 23 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Switching Waveforms
Read/Write Waveforms[25, 26, 27]
t
1
2
3
4
5
6
7
8
9
10
CYC
t
CLK
t
t
t
t
t
CENS
CES
CENH
CEH
CL
CH
CEN
CE
ADV/LD
W E
BW
X
A1
A2
A4
A3
A5
A6
A7
ADDRESS
DQ
t
CDV
t
t
AS
AH
t
t
t
t
CHZ
DOH
OEV
CLZ
D(A1)
t
D(A2)
D(A2+1)
Q(A3)
Q(A4)
Q(A4+1)
D(A5)
Q(A6)
D(A7)
t
OEHZ
t
DS
DH
t
DOH
t
OELZ
OE
COM M AND
W RITE
D(A1)
W RITE
D(A2)
BURST
W RITE
READ
Q(A3)
READ
Q(A4)
BURST
READ
W RITE
D(A5)
READ
Q(A6)
W RITE
D(A7)
DESELECT
D(A2+1)
Q(A4+1)
DON’T CARE
UNDEFINED
Notes:
For this waveform ZZ is tied LOW.
25.
26. When CE is LOW, CE is LOW, CE is HIGH and CE is LOW. When CE is HIGH, CE is HIGH or CE is LOW or CE is HIGH.
1
2
3
1
2
3
27. Order of the Burst sequence is determined by the status of the MODE (0 = Linear, 1 = Interleaved). Burst operations are optional.
Document #: 38-05356 Rev. *F
Page 24 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Switching Waveforms (continued)
NOP, STALL and DESELECT Cycles[25, 26, 28]
1
2
3
4
5
6
7
8
9
10
CLK
CEN
CE
ADV/LD
WE
BW [A:D]
ADDRESS
A1
A2
A3
A4
A5
t
CHZ
D(A1)
Q(A2)
Q(A3)
D(A4)
Q(A5)
DQ
t
DOH
COMMAND
WRITE
D(A1)
READ
Q(A2)
STALL
READ
Q(A3)
WRITE
D(A4)
STALL
NOP
READ
Q(A5)
DESELECT
CONTINUE
DESELECT
DON’T CARE
UNDEFINED
Note:
28. The IGNORE CLOCK EDGE or STALL cycle (Clock 3) illustrates CEN being used to create a pause. A write is not performed during this cycle.
Document #: 38-05356 Rev. *F
Page 25 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Switching Waveforms (continued)
ZZ Mode Timing[29, 30]
CLK
t
t
ZZ
ZZREC
ZZ
t
ZZI
I
SUPPLY
I
DDZZ
t
RZZI
ALL INPUTS
(except ZZ)
DESELECT or READ Only
Outputs (Q)
High-Z
DON’T CARE
Notes:
29. Device must be deselected when entering ZZ mode. See truth table for all possible signal conditions to deselect the device.
30. DQs are in High-Z when exiting ZZ sleep mode.
Document #: 38-05356 Rev. *F
Page 26 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Ordering Information
Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or
visit www.cypress.com for actual products offered.
Speed
(MHz)
Package
Diagram
Operating
Range
Ordering Code
Part and Package Type
133 CY7C1461AV33-133AXC
CY7C1463AV33-133AXC
CY7C1461AV33-133BZC
CY7C1463AV33-133BZC
51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
Commercial
51-85165 165-Ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm)
CY7C1461AV33-133BZXC 51-85165 165-Ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free
CY7C1463AV33-133BZXC
CY7C1465AV33-133BGC
CY7C1465AV33-133BGXC
CY7C1461AV33-133AXI
CY7C1463AV33-133AXI
CY7C1461AV33-133BZI
CY7C1463AV33-133BZI
CY7C1461AV33-133BZXI
CY7C1463AV33-133BZXI
CY7C1465AV33-133BGI
CY7C1465AV33-133BGXI
100 CY7C1461AV33-100AXC
CY7C1463AV33-100AXC
CY7C1461AV33-100BZC
CY7C1463AV33-100BZC
51-85167 209-Ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
209-Ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Pb-Free
51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
lndustrial
51-85165 165-Ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm)
51-85165 165-Ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free
51-85167 209-Ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
209-Ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Pb-Free
51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
Commercial
51-85165 165-Ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm)
CY7C1461AV33-100BZXC 51-85165 165-Ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free
CY7C1463AV33-100BZXC
CY7C1465AV33-100BGC
CY7C1465AV33-100BGXC
CY7C1461AV33-100AXI
CY7C1463AV33-100AXI
CY7C1461AV33-100BZI
CY7C1463AV33-100BZI
CY7C1461AV33-100BZXI
CY7C1463AV33-100BZXI
CY7C1465AV33-100BGI
CY7C1465AV33-100BGXI
51-85167 209-Ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
209-Ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Pb-Free
51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
lndustrial
51-85165 165-Ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm)
51-85165 165-Ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free
51-85167 209-Ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
209-Ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Pb-Free
Document #: 38-05356 Rev. *F
Page 27 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Package Diagrams
Figure 1. 100-Pin Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm), 51-85050
16.00 0.20
14.00 0.10
1.40 0.05
100
81
80
1
0.30 0.08
0.65
TYP.
12° 1°
(8X)
SEE DETAIL
A
30
51
31
50
0.20 MAX.
1.60 MAX.
R 0.08 MIN.
0.20 MAX.
0° MIN.
SEATING PLANE
STAND-OFF
0.05 MIN.
0.15 MAX.
NOTE:
1. JEDEC STD REF MS-026
0.25
GAUGE PLANE
2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH
MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.0098 in (0.25 mm) PER SIDE
R 0.08 MIN.
0.20 MAX.
BODY LENGTH DIMENSIONS ARE MAX PLASTIC BODY SIZE INCLUDING MOLD MISMATCH
3. DIMENSIONS IN MILLIMETERS
0°-7°
0.60 0.15
0.20 MIN.
1.00 REF.
51-85050-*B
DETAIL
A
Document #: 38-05356 Rev. *F
Page 28 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Package Diagrams (continued)
Figure 2. 165-Ball FBGA (15 x 17 x 1.4 mm), 51-85165
PIN 1 CORNER
BOTTOM VIEW
TOP VIEW
Ø0.05 M C
PIN 1 CORNER
1
Ø0.25 M C A B
Ø0.45 0.05(165X)
2
3
4
5
6
7
8
9
10
11
11 10
9
8
7
6
5
4
3
2
1
A
B
A
B
C
D
C
D
E
E
F
F
G
G
H
J
H
J
K
K
L
L
M
M
N
P
R
N
P
R
A
1.00
5.00
10.00
B
15.00 0.10
0.15(4X)
SEATING PLANE
C
51-85165-*A
Document #: 38-05356 Rev. *F
Page 29 of 31
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Package Diagrams (continued)
Figure 3. 209-Ball FBGA (14 x 22 x 1.76 mm), 51-85167
51-85167-**
NoBL and No Bus Latency are trademarks of Cypress Semiconductor Corporation. ZBT is a trademark of Integrated Device
Technology, Inc. All product and company names mentioned in this document are the trademarks of their respective holders.
Document #: 38-05356 Rev. *F
Page 30 of 31
© Cypress Semiconductor Corporation, 2004-2007. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the
use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to
be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
Document History Page
Document Title: CY7C1461AV33/CY7C1463AV33/CY7C1465AV33 36-Mbit (1M x 36/2 M x 18/512K x 72) Flow-Through
SRAM with NoBL™ Architecture
Document Number: 38-05356
Issue
Date
Orig. of
Change
REV. ECN NO.
Description of Change
**
254911 See ECN
SYT
New data sheet
Part number changed from previous revision. New and old part number differ by
the letter “A”
*A
300131 See ECN
SYT
Removed 150- and 117-MHz Speed Bins
Changed ΘJA and ΘJC from TBD to 25.21 and 2.58 °C/W, respectively, for TQFP
package
Added Pb-free information for 100-pin TQFP, 165 FBGA and 209 FBGA packages
Added “Pb-free BG and BZ packages availability” below the Ordering Information
*B
320813 See ECN
SYT
Changed H9 pin from VSSQ to VSS on the Pin Configuration table for 209 FBGA
Changed the test condition from VDD = Min. to VDD = Max for VOL in the Electrical
Characteristics table
Replaced the TBD’s for IDD, ISB1, ISB2, ISB3 and ISB4 to their respective values
Replaced TBD’s for ΘJA and ΘJC to their respective values on the Thermal Resis-
tance table for 165 FBGA and 209 FBGA Packages
Changed CIN, CCLK and CIO to 6.5, 3 and 5.5 pF from 5, 5 and 7 pF for TQFP
Package
Removed “Pb-free BG packages availability” comment below the Ordering Infor-
mation
*C
331551 See ECN
SYT
Modified Address Expansion balls in the pinouts for 165 FBGA and 209 FBGA
Packages according to JEDEC standards and updated the Pin Definitions accord-
ingly
Modified VOL, VOH test conditions
Replaced TBD to 100 mA for IDDZZ
Changed CIN, CCLK and CIO to 7, 7and 6 pF from 5, 5 and 7 pF for 165 FBGA
Package
Added Industrial Temperature Grade
Changed ISB2 and ISB4 from 100 and 110 mA to 120 and 135 mA respectively
Updated the Ordering Information by shading and unshading MPNs according to
availability
*D
417547 See ECN
RXU
Converted from Preliminary to Final
Changed address of Cypress Semiconductor Corporation on Page# 1 from “3901
North First Street” to “198 Champion Court”
Changed IX current value in MODE from –5 & 30 µA to –30 & 5 µA respectively
and also Changed IX current value in ZZ from –30 & 5 µA to –5 & 30 µA respectively
on page# 20
Modified test condition from VIH < VDD to VIH < VDD
Modified “Input Load” to “Input Leakage Current except ZZ and MODE” in the
Electrical Characteristics Table
Replaced Package Name column with Package Diagram in the Ordering
Information table
Replaced Package Diagram of 51-85050 from *A to *B
Updated the Ordering Information
*E
*F
473650 See ECN
VKN
Added the Maximum Rating for Supply Voltage on VDDQ Relative to GND.
Changed tTH, tTL from 25 ns to 20 ns and tTDOV from 5 ns to 10 ns in TAP AC
Switching Characteristics table.
Updated the Ordering Information table.
1274733 See ECN VKN/AESA Corrected typo in the “NOP, STALL and DESELECT Cycles” waveform
Document #: 38-05356 Rev. *F
Page 31 of 31
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明