MB39C022LPN [CYPRESS]
Switching Regulator, Current-mode, 1.6A, PDSO10, SON-10;型号: | MB39C022LPN |
厂家: | CYPRESS |
描述: | Switching Regulator, Current-mode, 1.6A, PDSO10, SON-10 开关 光电二极管 |
文件: | 总30页 (文件大小:1136K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MB39C022G/J/L/N
Buck DC/DC Converter + Low Noise LDO
The MB39C022 is a 2 channels power supply IC. It consists of one channel Buck DC/DC Converter and one channel LDO regulator.
The DC/DC converter has fast transient response with current mode control topology. Moreover, the integrated LDO provides an
auxiliary output supply for noise sensitive circuit.
Features
■ Power supply voltage range
: 2.5 V to 5.5 V
■ For Buck DC/DC included SW FET (CH1) : output 0.8 V to 4.5 V, 600 mA Max DC
■ For LDO (CH2)
: output 3.30 V (MB39C022G) 300 mA Max DC
: output 2.85 V (MB39C022J) 300 mA Max DC
: output 1.80 V (MB39C022L) 300 mA Max DC
: output 1.20 V (MB39C022N) 300 mA Max DC
■ Error amplifier threshold voltage
: 0.3 V (2.5%) (CH1)
■ Fast line transient response with current mode topology (CH1)
■ PFM mode at light load current with VO1/VIN1 80% (IO1 10 mA) (CH1)
■ Power-on-reset with 66 ms delay (CH1)
■ Built-in short circuit protect (CH2)
■ Built-in over current protect (CH1, CH2)
■ Built-in thermal protection function
■ Small size plastic SON-10 (3 mm × 3 mm) package
Applications
■ Portable Equipment
■ PND, GPS
■ PMP
■ Mobile TV, USB-dongle (CMMB, DVB-T, DMB-T)
■ Smart-phone
■ MP3
Cypress Semiconductor Corporation
Document Number: 002-08460 Rev. *A
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised February 24, 2016
MB39C022G/J/L/N
Contents
Pin Assignment ................................................................3
Pin Descriptions ..............................................................4
I/O Terminal Equivalent Circuit Diagram ........................5
Block Diagram ..................................................................6
Function Descriptions ......................................................7
PFM/PWM Logic Control Block (CH1) ........................7
Level converter and Iout Comparator circuit (CH1) .....7
Error Amp. circuit (CH1) ..............................................7
LDO Block (CH2) .........................................................7
POR Block ...................................................................7
Reference Voltage Block (VREF) ................................7
Under Voltage Lockout Protection
Circuit Block (UVLO) ...................................................8
Over Temperature Protection Block (OTP) .................8
Control Block (CTL) .....................................................8
Absolute Maximum Ratings ............................................9
Recommended Operating Conditions ..........................10
Electrical Characteristics ...............................................11
Test Circuit For Measuring Typical
Selection of components ...........................................14
DC/DC Output voltage setting ...................................15
Power On Reset (POR) .............................................15
Power dissipation and heat considerations ...............16
Board layout, design example ...................................17
Example Of Standard Operation Characteristics ........18
DC/DC Conversion Efficiency ...................................18
DC/DC Load Regulation ............................................18
DC/DC Line Regulation .............................................19
DC/DC Switching Waveform .....................................19
LDO Load Regulation ................................................20
LDO Line Regulation .................................................20
LDO Power Supply Rejection Ratio ..........................21
DC/DC Load Transient Waveforms ...........................21
DC/DC Power MOS FET ON Resistance ..................22
Application Circuits Examples ......................................24
Usage Precautions .........................................................26
Ordering Information ......................................................27
RoHS Compliance Information of
Operating Characteristics ..............................................13
Application Notes ...........................................................14
Lead(Pb) Free Version ...................................................27
Package Dimension ........................................................28
Document Number: 002-08460 Rev. *A
Page 2 of 30
MB39C022G/J/L/N
1. Pin Assignment
(TOP VIEW)
GND1
10
LX
9
VIN1
EN1
7
FB
6
8
1
2
3
4
5
EN2
VIN2
VOUT2
POR
GND2
(LCC-10P-M04)
Document Number: 002-08460 Rev. *A
Page 3 of 30
MB39C022G/J/L/N
2. Pin Descriptions
Block
Pin No.
Pin name
FB
I/O
Descriptions
CH1 Error Amplifier input pin
6
I
CH1 (Buck DC/DC)
9
LX
O
O
I
CH1 Inductor connection pin
CH2 LDO output pin
CH2 (LDO)
Control
3
VOUT2
EN1
7
CH1 Control pin (L : shutdown / H : operation)
CH2 Control pin (L : shutdown / H : operation)
CH1 Power supply pin
1
EN2
I
8
VIN1
VIN2
GND1
GND2
POR
–
–
2
CH2 Power supply pin
Power
10
5
–
CH1 Ground pin
–
CH2 Ground pin
Power-on Reset
4
O
CH1 Power on reset output pin (NMOS open drain)
Document Number: 002-08460 Rev. *A
Page 4 of 30
MB39C022G/J/L/N
3. I/O Terminal Equivalent Circuit Diagram
VIN1
EN∗
POR
∗
∗
GND2
GND2
VIN1
VIN1
∗
LX
FB
∗
GND1
GND2
VIN2
∗
∗
VOUT2
GND2
* : ESD Protection device
Document Number: 002-08460 Rev. *A
Page 5 of 30
MB39C022G/J/L/N
4. Block Diagram
<<CH1 Buck DC/DC>>
VIN1
Error
Amp.
6
8
9
FB
IO1 (600 mA Max)
VO1 (0.8 V to 4.5 V)
ICOMP
LX
PFM
PWM
Logic
DRV
Control
Current
Limit
LEVEL
CONV.
OSC
GND1
VIN2
10
VIN or VO1
POR
<<CH2: LDO>>
2
3
Error
Amp.
4
VOUT2
POR
POR
IO2 (300 mA Max)
VO2
3.3 V: MB39C022G
2.85 V: MB39C022J
1.8 V: MB39C022L
1.2 V: MB39C022N
OCP/SCP
VIN
GND2
(2.5 V to 5.5 V)
5
OTP
VREF
UVLO
EN1
EN2
7
1
enb1 (H: CH1 ON)
enb2 (H: CH2 ON)
<<10 PIN>>
Document Number: 002-08460 Rev. *A
Page 6 of 30
MB39C022G/J/L/N
5. Function Descriptions
5.1 PFM/PWM Logic Control Block (CH1)
The built-in P-ch and N-ch MOS FETs are controlled for synchronization rectification according to the frequency (2.0 MHz) oscillated
from the built-in oscillator (square wave oscillation circuit). Under light load, it operates intermittently.
This circuit protects the through current caused by synchronous rectification and the reverse current in Discontinuous Conduction
Mode.
Since the PWM control circuit of this IC is in the control method in current mode, the current peak value is monitored and controlled
as required.
5.2 Level converter and Iout Comparator circuit (CH1)
The Level converter circuit detects the current (ILX) which flows to the external inductor from the built-in P-ch MOS FET. By comparing
VIDET obtained through I-V conversion of peak current IPK of ILX with the Error Amp. output, the Iout Comparator turns off the built-in
P-ch MOS FET via the PWM Logic Control circuit.
5.3 Error Amp. circuit (CH1)
The error amplifier (Error Amp.) detects the output voltage from the DC/DC converter and output to the current comparators (ICOMP).
The output voltage setting resistor externally connected to FB allows an arbitrary output voltage to be set.
5.4 LDO Block (CH2)
The integrated low noise low dropout regulator (LDO) is available up to 300 mA current capability and 700 mA over current protection
(OCP) 350 mA short circuit protection (SCP). The LDO output VOUT2 requires a 4.7 μF capacitor for MB39C022G and MB39C022N
and a 1.0 μF capacitor for MB39C022J and MB39C022L for stability. MB39C022G, MB39C022J, MB39C022L and MB39C022N have
fixed 3.3 V, 2.85 V, 1.8 V and 1.2 V output voltages respectively, eliminating the need for an external resistor divider.
5.5 POR Block
The POR circuit monitors the VO1 through the FB pin voltage. When the FB pin voltage reaches 97 of VFBTH, POR pin becomes
high level after the hold time of 66 ms. The POR pin is an open-drain output and pulled up to VIN or VO1 with an external resistor.
Timing Chart : (POR pin pulled up to VIN with resistor)
VUVLO
VIN
EN1
VTH × 97%
FB
POR
thold
thold
V
V
: UVLO threshold voltage (VT = 2.050 V)
LH
UVLO
: FB pin threshold voltage (V = 0.3 V)
TH
TH
5.6 Reference Voltage Block (VREF)
A high accuracy reference voltage is generated with BGR (bandgap reference) circuit.
Document Number: 002-08460 Rev. *A
Page 7 of 30
MB39C022G/J/L/N
5.7 Under Voltage Lockout Protection Circuit Block (UVLO)
The circuit protects against IC malfunction and system destruction/deterioration in a transitional state or a momentary drop of when
the internal reference voltage starts. It detects a voltage drop at the VIN1 pin and stops IC operation. When voltages at the VIN1 pin
exceed the threshold voltage of the under voltage lockout protection circuit, the system is restored.
5.8 Over Temperature Protection Block (OTP)
The circuit protects an IC from heat-destruction. If the junction temperature reaches 135°C, the circuit turns off the CH1 and CH2
operation, When the junction temperature comes down to 110°C, the CH1 and CH2 are returned to the normal operation.
5.9 Control Block (CTL)
■ Control function table
EN1
EN2
CH1 and POR
CH2
VREF, UVLO, OTP
L
L
OFF
ON
OFF
OFF
ON
OFF
ON
ON
ON
H
L
L
H
H
OFF
ON
H
ON
Document Number: 002-08460 Rev. *A
Page 8 of 30
MB39C022G/J/L/N
6. Absolute Maximum Ratings
Parameter
Symbol
Condition
Rating
Min
0.3
0.3
0.3
0.3
0.3
0.3
0.3
–
Unit
Max
Power supply voltage
Input voltage
VIN1
VIN2
VFB
VEN1
VEN2
VPOR
VLX
VIN1 pin
6.0
V
VIN2 pin
VIN1 0.3
VIN1 0.3
6.0
6.0
6.0
V
FB pin
V
EN1 pin
V
EN2 pin
V
POR pull-up voltage
LX voltage
POR pin
V
LX pin
VIN1 0.3
1.6
V
LX peak current
VOUT2 peak current
Power dissipation
ILX
LX pin AC
VOUT2 pin AC
Ta 25°C
A
IO2
–
0.8
A
2
PD
–
2632*1,
*
mW
3
–
980*1,
1053*1,
* *
*
2,
4
Ta = 85°C
–
3,
4
–
392*1,
* *
Storage temperature
TSTG
–
55
125
°C
*1: When mounted on four layer epoxy board of 11.7 cm × 8.4 cm
*2: At connect the exposure pad and with thermal via (Thermal via 4 pcs).
*3: At connect the exposure pad and not thermal via.
*4: Power dissipation value between 25°C and 85°C is obtained by connecting these two points with a straight line
Notes:
• The use of negative voltages below 0.3 V to the GND pin may create parasitic transistors on LSI lines, which can cause
abnormal operation.
• If LX terminal is short-circuited to VIN1 or VIN2 or GND line, there is a possibility to destroy it. Such usage is prohibit
WARNING:
Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
Document Number: 002-08460 Rev. *A
Page 9 of 30
MB39C022G/J/L/N
7. Recommended Operating Conditions
Value
Typ
Parameter
Symbol
VIN1
Condition
Unit
Max
Min
3, 4,
5
Power supply voltage
VIN1 pin*1,
VIN2 pin*2,
FB pin
*
*
*
*
2.5
3.7
5.5
V
3
VIN2
VFB
Input voltage
–
0
0.30
–
V
V
V
V
A
A
°C
VEN1
VEN2
VO1
ILX
EN1 pin
–
5.5
5.5
4.5
0.6
0.3
85
EN2 pin
0
–
5
Output voltage
Output current
CH1 : Buck DC/DC*1,
*
0.8
–
–
LX pin DC
–
IVOUT2
Ta
VOUT2 pin DC
–
–
–
Operating ambient
temperature
40
25
*1 : The minimum VIN1 has to meet two conditions : VIN1 ≥ (VIN1 Min) and VIN1 ≥ VO1 0.5 V
*2 : The minimum VIN2 has to meet two conditions : VIN2 ≥ (VIN2 Min) and VIN2 ≥ VO2 Vdrop (VO2 and Vdrop values are specified
in “Electrical Characteristics”)
*3 : VIN1 ≥ VIN2
*4 : VIN1 startup rise time 1 ms is recommended
*5 : PFM mode at light load current with VO1/VIN1 80% (IO1 10 mA)
WARNING:
The recommended operating conditions are required in order to ensure the normal operation of
the semiconductor device. All of the device's electrical characteristics are warranted when the
device is operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges.
Operation outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented
on the data sheet. Users considering application outside the listed conditions are advised to contact
their representatives beforehand.
Document Number: 002-08460 Rev. *A
Page 10 of 30
MB39C022G/J/L/N
8. Electrical Characteristics
(Ta = 25°C, VIN1 = VIN2 = 3.7 V)
Value
Unit
Parameter
Symbol Pin No.
Condition
Min
Typ
Max
2.5%
100
–
Threshold voltage
Input Bias current
VTH
IFB
6
FB pin
2.5% 0.3
V
6
FB = 0 V
100
0
nA
Ω
SW PMOS-Tr On
resistor
RPON
8,9
ILX = 100 mA
–
0.35
CH1
[ Buck
DC/DC ]
SW NMOS-Tr On
resistor
RNON
9,10
ILX = 100 mA
–
0.25
–
Ω
Line regulation
Vline1
Vload1
ILIM1
VO2
–
–
VIN1 = 2.5 V to 5.5 V*1
IO1 = 100 mA to 600 mA
VOUT1 × 0.9
–
10
10
1.2
–
mV
mV
A
Load regulation
Over current protect
–
–
9
0.9
1.5
3
IO2 = 0 mA to 300 mA
2.5% 3.30
2.5% 2.85
2.5% 1.80
2.5% 1.20
2.5%
V
MB39C022G
IO2 = 0 mA to 300 mA
2.5%
2.5%
2.5%
V
V
V
MB39C022J
Output voltage
IO2 = 0 mA to 300 mA
MB39C022L
IO2 = 0 mA to 300 mA
MB39C022N
Line regulation
Load regulation
Vline2
3
3
VIN2 = 2.5 V to 5.5 V*2
–
–
–
–
10
25
–
mV
mV
mV
Vload2
IO2 = 0 mA to 300 mA
–
IO2 = 300 mA,
200
Drop out voltage
Vdrop
3
VIN2 = VO2 :
MB39C022G, MB39C022J
MB39C022G*3
MB39C022J*3
MB39C022L*3
MB39C022N*3
f = 1 kHz
f = 10 kHz
f = 1 kHz
f = 10 kHz
f = 1 kHz
f = 10 kHz
f = 1 kHz
f = 10 kHz
–
–
–
–
–
–
–
–
–
70*4
70*4
65*4
65*4
60*4
60*4
55*4
55*4
55*4
–
–
–
–
–
–
–
–
–
dB
CH2
[ LDO ]
dB
dB
Power supply
rejection ratio
dB
PSRR
3
dB
dB
dB
dB
Output noise
voltage
Vnoise
ILIM2
3
3
3
f = 10 Hz to 100 kHz,
EN1 = 0 V
μVrms
Over current
protect
VO2 × 0.9
500
150
700
350
980
700
mA
mA
Short circuit
protect
ISCP2
VO2 = 0 V
(Continued)
Document Number: 002-08460 Rev. *A
Page 11 of 30
MB39C022G/J/L/N
(Continued)
(Ta = 25°C, VIN1 = VIN2 = 3.7 V)
Value
Unit
Parameter
Symbol
Thold
Pin No.
Condition
fosc = 2 MHz
Min
52.8
Typ
Max
Hold time
4
66
79.2
ms
V
Power On Reset
[ POR ]
Output voltage
Output current
VPOR
IPOR
4
POR = 250 μA
POR = 5.5 V
VIN1
–
–
0.1
1
4
–
–
μA
V
Under Voltage
Lockout
Threshold voltage VTHL
2, 8
1.95
2.10
2.25
Protection
Circuit Block
[ UVLO ]
Hysteresis width VH
2, 8
–
–
0.20
–
V
Over
Stop temperature TOTPH
–
–
–
–
–
–
135
25
–
–
°C
°C
Temperature
Protection Block
[ OTP ]
Hysteresis width TOTPHYS
Oscillator Block Output
fosc
9
–
1.6
2.0
2.4
MHz
[ OSC ]
frequency
Control Block
[CTL ]
Input voltage
VIH
1, 7
1, 7
1, 7
8
EN1, EN2 ON
1.5
–
–
–
V
VIL
EN1, EN2 OFF
EN1, EN2 = 0 V
EN1, EN2 = 0 V
EN1, EN2 = 0 V
–
0.4
V
Input current
IEN
100
–
0
100
1
nA
μA
μA
Shut down
power supply
current
ICC1
ICC1
0
2
–
0
1
Standby power
supply current
(DC/DC)
ICC2
ICC2
8
2
EN1 = VIN1, EN2 = 0 V
IO1 = 0 mA, VFB = VIN1
–
–
30
0
60
1
μA
General
Standby power
supply current
(LDO)
ICC3
ICC3
8
2
EN1 = 0 V, EN2 = VIN1
IO2 = 0 mA
–
–
10
60
18
μA
120
Power-on
invalid
current
ICC4
ICC4
8
2
EN1, EN2 = VIN1,
VFB = 0.2 V
–
–
0.9
60
1.5
mA
120
μA
*1 : The minimum VIN1 has to meet two conditions : VIN1 ≥ (VIN1 Min) and VIN1 ≥ VO1 0.5 V
*2 : The minimum VIN2 has to meet two conditions : VIN2 ≥ (VIN2 Min) and VIN2 ≥ VO2 Vdrop (VO2 and Vdrop
values are specified in “ Electrical Characteristics”)
*3 : VIN2 = VO2 1 V, (MB39C022N: VIN2 = 2.5 V), IO2 = 100 mA
*4 : This value is not be specified. This should be used as a reference to support designing the circuits.
Document Number: 002-08460 Rev. *A
Page 12 of 30
MB39C022G/J/L/N
9. Test Circuit For Measuring Typical Operating Characteristics
EN2
EN2
GND1
LX
C2
VIN2
VO1
C4
C5
L1
VO2
VOUT2
POR
VIN1
EN1
FB
VIN
C1
POR
EN1
R3
R5
R6
C3
GND2
Component
Item
Specification
Remarks
C1
C2
C3
C4
C5
Ceramic capacitor
Ceramic capacitor
Ceramic capacitor
Ceramic capacitor
Ceramic capacitor
10 μF
4.7 μF
22 pF
4.7 μF
1 μF
for MB39C022J, MB39C022L
for MB39C022G, MB39C022N
4.7 μF
2.2 μH
1 MΩ
L1
Inductor
Resistor
Resistor
Resistor
R3
R5
R6
600 kΩ
200 kΩ
at VO1 = 1.2 V*
* : The output voltage of VO1 can be adjusted by the external resistor divider R5.
(R5 + R6)
R6
(600 kΩ + 200 kΩ)
200 kΩ
V
= V
×
= 0.3 V ×
= 1.2 V
O1
ref
Document Number: 002-08460 Rev. *A
Page 13 of 30
MB39C022G/J/L/N
10. Application Notes
10.1 Selection of components
Selection of an external inductor for DC/DC
This IC is designed to operate well with a 2.2 μH inductor. Choosing larger values would lead to larger overshoot/undershoot during
load transient. Choosing a smaller value would lead to larger ripple voltage.
The inductor should be rated for a saturation current higher than the LX peak current value during normal operating conditions, and
should have a minimal DC resistance. (100 mΩ or less is recommended to improve efficiency.)
LX peak current value IPK is obtained by the following formula.
V - V
D
1
2
(V - V
) × V
OUT
IN
OUT
IN
OUT
IN
I
= I
+
×
×
= I
+
PK
OUT
OUT
L
fosc
2 × L × fosc × V
L
: External inductor value
: Load current (DC)
I
OUT
V
V
: Power supply voltage
: Output setting voltage
IN
OUT
D
: ON- duty to be switched ( = V
/V )
OUT IN
fosc : Switching frequency (2.0 MHz)
ex) At VIN = 3.7 V, VOUT = 1.2 V, IOUT = 0.6 A, L = 2.2 μH, fosc = 2.0 MHz
The maximum peak current value IPK
;
(V V
2 × L × fosc × V
) × V
(3.7 V 1.2 V) × 1.2 V
2 × 2.2 μH × 2 MHz × 3.7 V
IN
OUT
OUT
IN
I
= IOUT
= 0.6 A
= 0.69 A
PK
I/O capacitor selection
• DC/DC's output capacitor's finite equivalent series resistance (ESR) causes ripple voltages on output equal to the amount of
current variation multiplied by the ESR value. The output capacitor value also has a significant impact on the operating stability
of the device when used as a DC/DC converter. Therefore, Cypress generally recommends C2 = 4.7 μF as DC/DC output
capacitor, or a larger capacitor value can be used if ripple voltages are not suitable.
• For DC/DC, select a low ESR for the VIN1/VIN2 input capacitor to suppress dissipation from ripple currents. In addition, to
reduce startup overshoot for DC/DC and LDO, it is recommended that larger ceramic capacitor be used for input capacitors C1
and C4. Recommended values are C1 = 10 μF, C4 = 4.7 μF.
• Types of capacitors
Ceramic capacitors are effective for reducing the ESR and afford smaller DC/DC converter circuit. However, power supply
functions as a heat generator, therefore avoid using capacitor with the F-temperature rating ( 80% to 20%). Cypress
recommends capacitors with the B-temperature rating ( 10 to 20).
Normal electrolytic capacitors are not recommended due to their high ESR.
Tantalum capacitor will reduce ESR, however, it is dangerous to use because it turns into short mode when damaged. If you
insist on using a tantalum capacitor, Cypress recommends the type with an internal fuse.
Document Number: 002-08460 Rev. *A
Page 14 of 30
MB39C022G/J/L/N
10.2 DC/DC Output voltage setting
The output voltage VO1 of this IC is defined by the external resistive divider R5 & R6. Note that C3 is a capacitor used for improving
stability. Use a 22 pF cap for C3 should be suitable in all cases.
R5 R6
600 kΩ 200 kΩ
200 kΩ
V
= V
×
ref
= 0.3 V ×
= 1.2 V
O1
R6
VO1
MB39C022
C3
R5
6
FB
Vref
(0.3 V)
-
R6
+
10.3 Power On Reset (POR)
R3 and R4 are the pull-up resistors for POR (Pin 4). A 1 MΩ resistor is required to placed at either R3 or R4. When R3 has a 1 MΩ
resistor and R4 is open; the POR will be connected VIN. When R4 has a 1 MΩ resistor and R3 is open; the POR pin will be connected
to VO1.
By default, only R3 require a 1 MΩ resistor while R4 is open.
Document Number: 002-08460 Rev. *A
Page 15 of 30
MB39C022G/J/L/N
10.4 Power dissipation and heat considerations
The DC/DC is so efficient that no consideration is required in most cases. The LDO, on the other hand, would be the dominant heat
generator due to its inherent efficiency loss. Thus, if the IC is used at a high power supply voltage, heavy load, and low LDO output
voltage, or high temperature, it requires further consideration.
The internal loss (Pc) is roughly obtained from the following formula :
2
P = PC1 + P = I
× (RDC + D × RONP + (1 - D) × R
) + I
× V
C
C2
O1
ONN
O2 drop
P
P
: DC/DC continuity loss
: LDO continuity loss
C1
C2
RDC
D
: External inductor series resistance ( < 100 mΩ recommended)
: Switching ON-duty cycle ( = V / V )
OUT
IN
R
R
: Internal P-ch SW FET ON resistance
: Internal N-ch SW FET ON resistance
: DC/DC Load current
ONP
ONN
I
I
O1
O2
: LDO Load current
V
: LDO Dropout voltage
drop
The loss expressed by the above formula is continuity loss. The internal loss includes the switching loss and the control circuit loss
as well but they are so small compared to the continuity loss they can be ignored.
For PC1, consider the scenario with high temperature and heavy load (VIN = 3.7 V, VO1 = 1.2 V, IO1 = 0.6 A, Ta = 70°C). Here,
R
ONP=: 0.4 Ω and RONN=: 0.3 Ω according to the graph “MOS FET ON resistance vs. Operating ambient temperature”.
PC1 = 156 mW.
For PC2, consider the scenario with low output voltage (MB39C022N), high temperature and heavy load (VIN = 3.7 V,
VO2 = 1.2 V, IO2 = 0.3 A, Ta = 70°C). Here, PC2 = 0.75 W. Note that PC2 >> PC1
.
According to the graph “Power dissipation vs. Operating ambient temperature”, the maximum permissible power dissipation at an
operating ambient temperature Ta of 70°C is 1.4 W. The internal loss is lower than the maximum permissible power dissipation.
Document Number: 002-08460 Rev. *A
Page 16 of 30
MB39C022G/J/L/N
10.5 Board layout, design example
Some basic design guidelines should be used when physically placing the MB39C022 on a Printed Circuit Board (PCB).
• Regarding to GND pattern of PCB layout of MB39C022, It needs to separate like AGND (analog ground) and PGND (power
ground). By separating grounds, it is possible to minimize the switching frequency noise on the LDO output.
• Arrange the input capacitor C1 and C4 as close as possible between VIN1 & PGND pins and VIN2 & AGND pins. Make a through
hole near the pins of this capacitor if the board has planes for power and GND.
• Large AC currents flow between this IC and the input capacitor (C1), output capacitor (C2), and external inductor (L1). Group
these components as close as possible to this IC to reduce the overall loop area occupied by this group. Also try to mount these
components on the same surface and arrange wiring without through hole wiring. Use thick, short, and straight routes to wire
the net (The layout by planes is recommended.).
• The C1 and C2 capacitor returns are connected closely together at the PGND plane.
• The LDO input capacitor (C4) and LDO output capacitor (C5) are returned to the AGND plane.
• The analog ground plane and power ground plane are connected at one point.
• All other signals (EN1, EN2, FB) should be referenced to AGND and have the AGND plane underneath them.
• The feedback wiring to the VO1 and the VO1 pin should be wired closest to the output capacitor (C2). The resistive divider and
FB pin is extremely sensitive and should thus be kept wired away from the LX pin of this IC as far as possible.
• Try to make a GND plane on the surface to which this IC will be mounted. For efficient heat dissipation when using the SON-10
package, Cypress recommends providing a thermal via in the footprint of the thermal pad.
Layout Example of IC components
PGND
Plane
VO1
L1
PGND
C2
AGND Plane
VVIINN22
PGND
C4
AGND
CC11
C5
VIN1
VVOO22
RR66
R5
Document Number: 002-08460 Rev. *A
Page 17 of 30
MB39C022G/J/L/N
11. Example Of Standard Operation Characteristics
(Shown below is an example of characteristics for connection according to “ Test Circuit For Measuring Typical Operating
Characteristics”.)
11.1 DC/DC Conversion Efficiency
CH1 Test Condition :
EN1 = VIN; EN2 = 0 V
VO1 = 1.2 V; C1 = 10 μF; C2 = 4.7 μF
100
90
80
70
60
50
40
30
20
10
0
VIN = 3.7 V
VIN = 4.3 V
VIN = 5.5 V
0.001
0.01
0.1
1
Load Current IO1 (A)
11.2 DC/DC Load Regulation
CH1 Test Condition :
EN1 = VIN; EN2 = 0 V
VO1 = 1.2 V; C1 = 10 μF; C2 = 4.7 μF
1.3
1.28
VIN = 3.7 V
VIN = 4.3 V
VIN = 5.5 V
1.26
1.24
1.22
1.2
1.18
1.16
1.14
1.12
1.1
0
0.2
0.4
0.6
Load Current IO1 (A)
Document Number: 002-08460 Rev. *A
Page 18 of 30
MB39C022G/J/L/N
11.3 DC/DC Line Regulation
CH1 Test Condition :
EN1 = VIN; EN2 = 0 V
VO1 = 1.2 V; C1 = 10 μF; C2 = 4.7 μF
1.3
1.28
1.26
1.24
1.22
1.2
IO1 = 0 mA
IO1 = 300 mA
IO1 = 600 mA
1.18
1.16
1.14
1.12
1.1
3.2
3.7
4.2
4.7
5.2
Input Voltage VIN (V)
11.4 DC/DC Switching Waveform
CH1 Test Condition :
EN1 = EN2 = VIN = 3.7 V;
VO1 = 1.8 V; IO1 = 250 mA; C1 = 10 μF; C2 = 4.7 μF
VO2 = 3.3 V; IO2 = 150 mA; C4 = C5 = 4.7 μF
VLx
5 V/div
ILx
100 mA/div
VO1
20 mV/div
VO2
20 mV/div
500 ns/div
Document Number: 002-08460 Rev. *A
Page 19 of 30
MB39C022G/J/L/N
11.5 LDO Load Regulation
MB39C022G CH2 Test Condition :
EN2 = VIN; EN1 = 0 V
VO2 = 3.3 V; C4 = C5 = 4.7 μF
3.4
VIN = 3.7 V
3.38
VIN = 4.3 V
3.36
VIN = 5.5 V
3.34
3.32
3.3
3.28
3.26
3.24
3.22
3.2
0.25
0
0.05
0.1
0.15
0.2
0.3
Load Current IO2 (A)
11.6 LDO Line Regulation
MB39C022G CH2 Test Condition :
EN2 = VIN; EN1 = 0 V
VO2 = 3.3 V; C4 = C5 = 4.7 μF
3.4
3.38
IO2 = 0 mA
3.36
3.34
3.32
3.3
IO2 = 120 mA
IO2 = 300 mA
3.28
3.26
3.24
3.22
3.2
3.6
4.1
4.6
5.1
Input Voltage VIN (V)
Document Number: 002-08460 Rev. *A
Page 20 of 30
MB39C022G/J/L/N
11.7 LDO Power Supply Rejection Ratio
MB39C022G CH2 Test Condition :
EN2 = VIN = 3.7 V; EN1 = 0 V
VO2 = 3.3 V; IO2 = 100 mA; C1 = C4 = 0 μF
0
10
20
30
40
50
60
70
80
90
−
−
−
−
−
−
−
−
−
VIN = 3.7 V
VIN = 4.3 V
10
100
1000
10000
100000
1000000
Frequency (Hz)
11.8 DC/DC Load Transient Waveforms
Test Condition :
VIN = EN1 = EN2 = 3.7 V; VO1 = 1.2 V; C1 = 10 μF; C2 = 4.7 μF; VO2 = 3.3 V; C4 = C5 = 4.7 μF
T
IO1 = 10 mA to 400 mA
IO1
500 mA/div
VO1
100 mV/div
VO2
IO2 = 150 mA
20 mV/div
100 μs/div
CH1 Load Transient Waveforms
Document Number: 002-08460 Rev. *A
Page 21 of 30
MB39C022G/J/L/N
11.9 DC/DC Power MOS FET ON Resistance
P-ch MOS FET ON Resistance vs.
Operating Ambient Temperature
MOS FET ON Resistance vs. Input Voltage
0.6
0.5
0.6
0.5
0.4
0.3
0.2
0.1
0.0
P-ch
VIN = 3.7 V
0.4
0.3
0.2
N-ch
VIN = 5.5 V
0.1
0.0
2.0
3.0
4.0
5.0
6.0
-50
0
50
100
Input voltage V (V)
IN
Operating Ambient Temperature Ta (°C)
N-ch MOS FET ON Resistance vs.
Operating Ambient Temperature
0.6
0.5
0.4
0.3
0.2
0.1
0.0
VIN = 3.7 V
VIN = 5.5 V
-50
0
50
100
Operating Ambient Temperature Ta (°C)
Document Number: 002-08460 Rev. *A
Page 22 of 30
MB39C022G/J/L/N
Permissible Power Dissipation vs. Operating Ambient Temperature
3000
2630
2500
2000
1500
1000
500
0
-40
-20
0
20
40
60
80
100
Operating Ambient Temperature Ta (°C)
Document Number: 002-08460 Rev. *A
Page 23 of 30
MB39C022G/J/L/N
12. Application Circuits Examples
Example 1 (VIN1 = VIN2)
VIN1 and VIN2 are connected together and POR is pulled up to VIN
(MB39C022)
EN2
EN2
GND1
LX
C2
VO1
VIN2
IO1 ≤ 600 mA
C4
C5
L1
VO2
IO2 ≤ 300 mA
VOUT2
POR
VIN1
EN1
FB
VIN
C1
POR
EN1
R3
R6
R5
C3
GND2
Example 2 (VIN2 = VO1)
• VIN2 is connected to VO1 and POR is pulled up to VIN
• It is possible to maximize LDO efficiency by connecting DC/DC Output to LDO supply.
• Maximum DC/DC output current ( = IO1) is limited by VIN2 input current (=: IO2)
(MB39C022)
EN2
EN2
GND1
LX
C2
VO1
VIN2
IO1 ≤ 600 mA - IO2
C4
C5
L1
VO2
VOUT2
POR
VIN1
EN1
FB
IO2 ≤ 300 mA
VIN
C1
POR
EN1
R3
R6
C3
GND2
R5
Document Number: 002-08460 Rev. *A
Page 24 of 30
MB39C022G/J/L/N
Example 3 (POR and RC delay channel control)
• EN1 is controlled by RC delay and EN2 is controlled by POR output.
• It is possible to control each channel without signal from MCU
R3
(MB39C022)
EN2
GND1
LX
C2
VO1
VIN2
IO1 ≤ 600 mA
C4
C5
L1
VO2
IO2 ≤ 300 mA
VOUT2
POR
VIN1
EN1
FB
VIN
C1
100 kΩ
POR
1 μF
R5
R6
C3
GND2
Timing chart
VIN
VUVLO
Vth(POR)
VO1
(1.2 V)
VO2
tc
td
(1.8 V)
ta
tb
Start up control
t : RC delay time (28 ms at VIN = 3.7 V, R = 100 kΩ, C = 1 μF)
a
t : POR hold time (66 ms fixed)
b
Power down control
t , t : depend on internal discharge path and output loading
c
d
Document Number: 002-08460 Rev. *A
Page 25 of 30
MB39C022G/J/L/N
13. Usage Precautions
1. Never use setting exceeding maximum rated conditions.
Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of
absolute maximum ratings. Do not exceed these ratings.
2. Use the devices within recommended conditions
It is recommended that devices be operated within recommended conditions.
Exceeding the recommended operating condition may adversely affect devices reliability.
Nominal electrical characteristics are warranted within the range of recommended operating conditions otherwise specified on each
parameter in the section of electrical characteristics.
3. Design the ground line on printed circuit boards with consideration of common impedance.
4. Take appropriate measures against static electricity.
The LX pin has less built-in ESD protection than other pins.
LX pin : 150 V (MM), 1500 V (HBM), Other pins : 200 V (MM), 2000 V (HBM)
Containers for semiconductor materials should have anti-static protection or be made of conductive material.
After mounting, printed circuit boards should be stored and shipped in conductive bags or containers.
Work platforms, tools, and instruments should be properly grounded.
Working personnel should be grounded with resistance of 250 kΩ to 1 MΩ between body and ground.
5. Do not apply negative voltages
The use of negative voltages below 0.3 V may activate parasitic transistors on the device, which can cause abnormal operation.
Document Number: 002-08460 Rev. *A
Page 26 of 30
MB39C022G/J/L/N
14. Ordering Information
Part number
MB39C022GPN
Package
Remarks
MB39C022JPN
10-pin plastic SON
(LCC-10P-M04)
MB39C022LPN
MB39C022NPN
15. RoHS Compliance Information Of Lead(Pb) Free Version
The LSI products of Cypress with “E1” are compliant with RoHS Directive, and has observed the standard of lead, cadmium, mercury,
chromium, polybrominated biphenyls (PBB), and polybrominated diphenylethers (PBDE).
A product whose part number has trailing characters “E1” is RoHS compliant.
Document Number: 002-08460 Rev. *A
Page 27 of 30
MB39C022G/J/L/N
16. Package Dimension
10-pin plastic SON
Lead pitch
0.50 mm
3.00 mm × 3.00 mm
Plastic mold
Package width ×
package length
Sealing method
Mounting height
Weight
0.75 mm MAX
0.018 g
(LCC-10P-M04)
10-pin plastic SON
(LCC-10P-M04)
3.00 0.10
(.118 .004)
2.40 0.10
(.094 .004)
10
6
INDEX AREA
1.70 0.10
(.067 .004)
3.00 0.10
(.118 .004)
0.40 0.10
(.016 .004)
1
5
1PIN CORNER
(C0.30(C.012))
0.50(.020)
TYP
0.25 0.03
(.010 .001)
0.75(.030)
MAX
0.15(.006)
0.05(.002)
0.00 +–00..0005
+.002
(.000
)
–.000
Dimensions in mm (inches).
Note: The values in parentheses are reference values.
C
2008 FUJITSU MICROELECTRONICS LIMITED C10004S-c-1-2
Document Number: 002-08460 Rev. *A
Page 28 of 30
MB39C022G/J/L/N
Document History Page
Document Title: MB39C022G/J/L/N Buck DC/DC Converter + Low Noise LDO
Document Number: 002-08460
Orig. of
Change
Submission
Date
Revision
ECN
Description of Change
**
–
TAOA
TAOA
04/13/2009 Initial release
*A
5150068
02/24/2016 Migrated Spansion Datasheet from DS04-27271-2E to Cypress format
Document Number: 002-08460 Rev. *A
Page 29 of 30
MB39C022G/J/L/N
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
®
Products
PSoC Solutions
ARM® Cortex® Microcontrollers
cypress.com/arm
cypress.com/automotive
cypress.com/clocks
cypress.com/interface
cypress.com/powerpsoc
cypress.com/memory
cypress.com/psoc
cypress.com/psoc
Automotive
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP
Clocks & Buffers
Interface
Cypress Developer Community
Community | Forums | Blogs | Video | Training
Lighting & Power Control
Memory
Technical Support
cypress.com/support
PSoC
Touch Sensing
USB Controllers
Wireless/RF
cypress.com/touch
cypress.com/usb
cypress.com/wireless
© Cypress Semiconductor Corporation 2009-2016. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document,
including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries
worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other
intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress
hereby grants you under its copyright rights in the Software, a personal, non-exclusive, nontransferable license (without the right to sublicense) (a) for Software provided in source code form, to modify
and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either
directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units. Cypress also grants you a personal, non-exclusive, nontransferable, license (without the right
to sublicense) under those claims of Cypress's patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely to the minimum
extent that is necessary for you to exercise your rights under the copyright license granted in the previous sentence. Any other use, reproduction, modification, translation, or compilation of the Software
is prohibited.
CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes to this document without further notice. Cypress does not
assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or
programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application
made of this information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of
weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or
hazardous substances management, or other uses where the failure of the device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any
component of a device or system whose failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole
or in part, and Company shall and hereby does release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. Company shall indemnify
and hold Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress
products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United
States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 002-08460 Rev. *A
Revised February 24, 2016
Page 30 of 30
相关型号:
MB39C022LPNE1
Switching Regulator, Current-mode, 1.6A, 2400kHz Switching Freq-Max, PDSO10, 3 X 3 MM, 0.75 MM HEIGHT, 0.50 MM PITCH, PLASTIC, SON-10
FUJITSU
MB39C022NPNE1
1.6A SWITCHING REGULATOR, 2400kHz SWITCHING FREQ-MAX, PDSO10, 3 X 3 MM, 0.75 MM HEIGHT, 0.50 MM PITCH, PLASTIC, SON-10
FUJITSU
MB39C308BGF-E1
Switching Regulator, Current-mode, 4.5A, 840kHz Switching Freq-Max, PBGA208, 9 X 9 MM, 1.30 MM HEIGHT, 0.50 MM PITCH, ROHS COMPLIANT, PLASTIC, FBGA-208
FUJITSU
©2020 ICPDF网 联系我们和版权申明