S29CD016J0JFAI112 [CYPRESS]
Flash, 512KX32, 54ns, PBGA80, BGA-80;
| 型号： | S29CD016J0JFAI112 |
| 厂家： | 
CYPRESS |
| 描述： | Flash, 512KX32, 54ns, PBGA80, BGA-80 |
| 文件： | 总74页 (文件大小：1356K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
S29CD032J
S29CD016J
S29CL032J
S29CL016J
32/16 Mbit, 2.6/3.3 V, Dual Boot,
Simultaneous Read/Write, Burst Flash
General Description
The Cypress S29CD-J and S29CL-J devices are Floating Gate products fabricated in 110-nm process technology. These burst-
mode Flash devices are capable of performing simultaneous read and write operations with zero latency on two separate banks,
using separate data and address pins. These products can operate up to 75 MHz (32 Mb) or 66 MHz (16 Mb), and use a single VCC
of 2.5V to 2.75V (S29CD-J) or 3.0V to 3.6V (S29CL-J) that make them ideal for today’s demanding automotive applications.
Distinctive Characteristics
Single 2.6V (S29CD-J) or 3.3V (S29CL-J) for read/program/
Supports Common Flash Interface (CFI)
Extended Temperature range
erase
110 nm Floating Gate Technology
Simultaneous Read/Write operation with zero latency
x32 Data Bus
Persistent and Password methods of Advanced Sector
Protection
Unlock Bypass program command to reduce programming
time
Dual Boot Sector Configuration (top and bottom)
ACC input pin to reduce factory programming time
Flexible Sector Architecture
Data Polling bits indicate program and erase operation
– CD016J and CL016J: Eight 2k Double word, Thirty 16k
Double word, and Eight 2k Double Word sectors
– CD032J and CL032J: Eight 2k Double word, Sixty-two 16k
Double Word, and Eight 2k Double Word sectors
completion
Hardware (WP#) protection of two outermost sectors in the
large bank
VersatileI/O™ control (1.65V to 3.6V)
Ready/Busy (RY/BY#) output indicates data available to
system
Programmable Burst Interface
Suspend and Resume commands for Program and Erase
– Linear for 2, 4, and 8 double word burst with wrap around
Operation
Secured Silicon Sector that can be either factory or
Offered Packages
customer locked
– 80-pin PQFP
20 year data retention (typical)
– 80-ball Fortified BGA (13 x 11 mm and 11 x 9mm versions)
– Pb-free package option available
– Known Good Die
Cycling Endurance: 1 million write cycles per sector (typical)
Command set compatible with JEDEC (JC42.4) standard
Cypress Semiconductor Corporation
Document Number: 002-00948 Rev. *C
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised November 08, 2017
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Performance Characteristics
Read Access Times
75 (32 Mb only)
Speed Option (MHz)
66
54
8
56
54
8
40
54
8
Max Asynch. Access Time, ns (tACC
Max Synch. Burst Access, ns (tBACC
Min Initial Clock Delay (clock cycles)
Max CE# Access Time, ns (tCE
Max OE# Access time, ns (tOE
)
54
8
)
5
5
5
4
)
54
20
54
20
54
20
54
20
)
Current Consumption (Max values)
Continuous Burst Read @ 75 MHz
90 mA
50 mA
50 mA
60 µA
Program
Erase
Standby Mode
Typical Program and Erase Times
Double Word Programming
Sector Erase
18 µs
1.0 s
Notice for the 32Mb S29CD-J and S29CL-J devices only:
Refer to the application note “Recommended Mode of Operation for Cypress® 110 nm S29CD032J/S29CL032J Flash Memory”
publication number S29CD-CL032J_Recommend_AN for programming best practices.
Document Number: 002-00948 Rev. *C
Page 2 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Contents
1.
Ordering Information................................................... 4
9.2 Secured Silicon Sector Entry
and Exit Commands...................................................... 45
1.1 Valid Combinations........................................................ 5
10. Electronic Marking...................................................... 46
2.
Input/Output Descriptions
and Logic Symbols...................................................... 6
11. Power Conservation Modes....................................... 46
11.1 Standby Mode............................................................... 46
11.2 Automatic Sleep Mode.................................................. 46
11.3 Hardware RESET# Input Operation.............................. 46
11.4 Output Disable (OE#).................................................... 46
3.
4.
Block Diagram.............................................................. 7
Block Diagram of Simultaneous
Read/Write Circuit........................................................ 8
5.
Physical Dimensions/Connection Diagrams............. 9
12. Electrical Specifications............................................. 47
12.1 Absolute Maximum Ratings.......................................... 47
5.1 80-Pin PQFP Connection Diagram................................ 9
5.2 PQR080–80-Lead Plastic Quad Flat
Package Physical Dimensions..................................... 10
5.3 80-Ball Fortified BGA Connection Diagram ................. 11
5.4 Special Package Handling Instructions........................ 11
5.5 LAA080–80-ball Fortified Ball Grid Array
13. Operating Ranges....................................................... 48
14. DC Characteristics...................................................... 49
14.1 Zero Power Flash.......................................................... 50
(13 x 11 mm) Physical Dimensions.............................. 12
5.6 LAD080–80-ball Fortified Ball Grid Array
15. Test Conditions........................................................... 51
16. Test Specifications ..................................................... 51
16.1 Switching Waveforms ................................................... 51
(11 x 9 mm) Physical Dimensions................................ 13
6.
6.1 Memory Map................................................................ 14
7. Device Operations ..................................................... 19
7.1 Device Operation Table ............................................... 19
7.2 Asynchronous Read..................................................... 20
7.3 Hardware Reset (RESET#).......................................... 21
7.4 Synchronous (Burst) Read Mode
and Configuration Register .......................................... 21
7.5 Autoselect .................................................................... 26
7.6 VersatileI/O (VIO) Control............................................. 27
7.7 Program/Erase Operations .......................................... 27
7.8 Write Operation Status................................................. 32
7.9 Reset Command.......................................................... 36
Product Overview ...................................................... 14
17. AC Characteristics...................................................... 52
17.1 VCC and VIO Power-up.................................................. 52
17.2 Asynchronous Operations............................................. 52
17.3 Synchronous Operations .............................................. 54
17.4 Hardware Reset (RESET#)........................................... 56
17.5 Write Protect (WP#)...................................................... 57
17.6 Erase/Program Operations........................................... 57
17.7 Alternate CE# Controlled
Erase/Program Operations........................................... 62
17.8 Erase and Programming Performance ......................... 63
17.9 PQFP and Fortified BGA Pin Capacitance ................... 63
18. Appendix 1 .................................................................. 64
18.1 Common Flash Memory Interface (CFI) ....................... 64
8.
Advanced Sector Protection/Unprotection ............. 37
19. Appendix 2 .................................................................. 67
19.1 Command Definitions.................................................... 67
8.1 Advanced Sector Protection Overview ........................ 38
8.2 Persistent Protection Bits............................................. 39
8.3 Persistent Protection Bit Lock Bit................................. 41
8.4 Dynamic Protection Bits............................................... 41
8.5 Password Protection Method....................................... 42
8.6 Hardware Data Protection Methods............................. 43
20. Revision History.......................................................... 69
Sales, Solutions, and Legal Information .......................... 74
Worldwide Sales and Design Support ........................... 74
Products ........................................................................ 74
PSoC® Solutions .......................................................... 74
Cypress Developer Community ..................................... 74
Technical Support ......................................................... 74
9.
Secured Silicon Sector Flash Memory Region ....... 44
9.1 Secured Silicon Sector Protection Bit .......................... 45
Document Number: 002-00948 Rev. *C
Page 3 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
1. Ordering Information
The order number (Valid Combination) is formed by the following:
S29CD032J
S29CL032J
0
J
F
A
I
0
0
0
Packing Type
0 = Tray, FBGA: 180 per tray, min. 10 trays per box
Tray, PQFP: 66 per tray, min. 10 trays per box
2 = 7” Tape and Reel, FBGA: 400 per reel
3 = 13” Tape and Reel, FBGA: 1600 per reel
13” Tape and Reel, PQFP: 500 per reel
Boot Sector Option (16th Character)
0 = Top Boot with Simultaneous Operation
1 = Bottom Boot with Simultaneous Operation
2 = Top Boot without Simultaneous Operation
3 = Bottom Boot without Simultaneous Operation
Autoselect ID Option (15th Character)
0 = 7E, 08, 01/00 Autoselect ID
1 = 7E, 36, 01/00 Autoselect ID
0 = 7E, 46, 01/00 Autoselect ID
0 = 7E, 09, 01/00 Autoselect ID
0 = 7E, 49, 01/00 Autoselect ID
S29CD016J only
S29CL016J only
S29CD032J only
S29CL032J only
Temperature Range
I = Industrial (–40 °C to +85 °C)
M = Extended (–40 °C to +125 °C)
Material Set
A = Standard
F = Pb-free Option
Package Type
Q = Plastic Quad Flat Package (PQFP)
F = Fortified Ball Grid Array, 1.0 mm pitch package, 13 11 mm package
B = Fortified Ball Grid Array, 1.0 mm pitch package, 11 9 mm package
Clock Frequency (11th Character)
J = 40 MHz
M = 56 MHz
P = 66 MHz
R = 75 MHz
Initial Burst Access Delay (10th Character)
0 = 5-1-1-1, 6-1-1-1, and above
1 = 4-1-1-1 (40 MHz only)
Device Number/Description
S29CD032J/S29CD016J (2.5 volt-only), S29CL032J/S29CL016J (3.3 Volt-only)
32 or 16 Mbit (1M or 512k 32-Bit) CMOS Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory
Manufactured on 110 nm floating gate technology
Document Number: 002-00948 Rev. *C
Page 4 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
1.1
Valid Combinations
Valid Combinations lists configurations planned to be supported in volume for this device. Consult your local sales office to confirm
availability of specific valid combinations and to check on newly released combinations.
S29CD-J/CL-J Valid Combinations
Device
Number
Initial Burst
Access Delay
Clock
Frequency
Package Material Temperature Autoselect ID Boot Sector Packing
Type
Set
Range
Option
Option
Type
Q
0, 3
0, 1
0
J
B, F
Q
0, 2, 3
0, 3
S29CD016J
S29CL016J
0, 1
M, P
J
B, F
Q
0, 2, 3
0, 3
0, 1
0
B, F
Q
0, 2, 3
0, 3
0, 1, 2, 3
M, P
J
B, F
Q
0, 2, 3
0, 3
0, 1
B, F
Q
0, 2, 3
0, 3
M, P
B, F
0, 2, 3
S29CD032J
A, F
I, M
0, 1 (2)
2, 3
0
0, 1
0
Q
0, 3
R
0
0, 1 (2)
2, 3
B, F
0, 2, 3
Q
0, 3
0, 2, 3
0, 3
J
B, F
Q
0, 1, 2, 3
M, P
B, F
0, 2, 3
S29CL032J
0, 1 (2)
2, 3
Q
0, 3
R
0, 1 (2)
2, 3
B, F
0, 2, 3
Notes
1. The ordering part number that appears on BGA packages omits the leading “S29”.
2. Contact factory for availability.
Document Number: 002-00948 Rev. *C
Page 5 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
2. Input/Output Descriptions and Logic Symbols
Table identifies the input and output package connections provided on the device.
Symbol
Type
Description
Address lines for S29CD-J and S29CL-J (A18-A0 for 16 Mb and A19-A0 for 32 Mb). A9 supports
12V autoselect input.
A19-A0
Input
DQ31-DQ0
CE#
I/O
Data input/output
Input
Chip Enable. This signal is asynchronous relative to CLK for the burst mode.
OE#
Input
Output Enable. This signal is asynchronous relative to CLK for the burst mode.
WE#
VCC
Input
Write Enable
Supply
Supply
Supply
Device Power Supply. This signal is asynchronous relative to CLK for the burst mode.
VersatileI/OTM Input.
VIO
VSS
Ground
NC
No Connect Not connected internally
Ready/Busy output and open drain which require a external pull up resistor.
When RY/BY# = VOH, the device is ready to accept read operations and commands. When RY/BY#
= VOL, the device is either executing an embedded algorithm or the device is executing a hardware
reset operation.
RY/BY#
Output
Clock Input that can be tied to the system or microprocessor clock and provides the fundamental
timing and internal operating frequency.
CLK
ADV#
IND#
Input
Input
Load Burst Address input. Indicates that the valid address is present on the address inputs.
End of burst indicator for finite bursts only. IND is low when the last word in the burst sequence is at
the data outputs.
Output
Output
Input
WAIT#
WP#
Provides data valid feedback only when the burst length is set to continuous.
Write Protect Input. At VIL, disables program and erase functions in two outermost sectors of the
large bank.
Acceleration input. At VHH, accelerates erasing and programming. When not used for acceleration,
ACC
Input
Input
ACC = VSS or VCC
.
RESET#
Hardware Reset.
Document Number: 002-00948 Rev. *C
Page 6 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
3. Block Diagram
VCC
VSS
DQmax–DQ0
Erase Voltage
Generator
Input/Output
Buffers
VIO
WE#
RESET#
State
Control
ACC
WP#
Command
Register
PGM Voltage
Generator
Data
Chip Enable
CE#
OE#
Output Enable
Y-Decoder
X-Decoder
Y-Gating
VCC
Detector
Timer
Cell Matrix
ADV#
CLK
Burst
State
Control
Burst
Address
Counter
IND/
WAIT#
Amax-A0
Amax-A0
Note
3.Address bus is A19–A0 for 32 Mb device, A18–A0 for 16 Mb device. Data bus is D31–DQ0.
Document Number: 002-00948 Rev. *C
Page 7 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
4. Block Diagram of Simultaneous Read/Write Circuit
OE#
V
V
CC
SS
Upper Bank Address
A –A0
max
Upper Bank
X-Decoder
A
–A0
max
STATE
CONTROL
&
COMMAND
REGISTER
RESET#
WE#
Status
DQ
–DQ0
max
CE#
Control
ADV#
DQ
–DQ0
max
X-Decoder
Lower Bank
A
–A0
max
Lower Bank Address
Document Number: 002-00948 Rev. *C
Page 8 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
5. Physical Dimensions/Connection Diagrams
5.1
80-Pin PQFP Connection Diagram
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
DQ16
DQ17
DQ18
DQ19
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
DQ15
DQ14
DQ13
DQ12
V
V
V
IO
SS
IO
V
SS
DQ20
DQ21
DQ22
DQ23
DQ24
DQ25
DQ26
DQ27
DQ11
DQ10
DQ9
DQ8
DQ7
DQ6
DQ5
DQ4
80-Pin PQFP
V
V
V
IO
SS
IO
V
SS
DQ28
DQ29
DQ30
DQ31
NC
DQ3
DQ2
DQ1
DQ0
A19
A18
A17
A16
A0
A1
A2
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
Notes
4. On 16 Mb device, pin 44 (A19) is NC.
5. Pin 69 (RY/BY#) is Open Drain and requires an external pull-up resistor.
Document Number: 002-00948 Rev. *C
Page 9 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
5.2
PQR080–80-Lead Plastic Quad Flat Package Physical Dimensions
6
3
D
D1
D3
0.20 MIN. FLAT SHOULDER
PIN S
PIN R
7˚
TYP.
0˚MIN.
0.30 ± 0.05 R
PIN ONE I.D.
A
GAGE
PLANE
0.25
7˚
TYP.
L
E3
3
ccc
C
b
4
0˚-7˚
E1
6
-A-
-B-
aaa
M
A B S D S
C
E
DETAIL X
SEE NOTE 3
b
PIN P
-D-
SEE DETAIL X
PIN Q
c
e
BASIC
SECTION S-S
2
S
A2
A
-A-
-C-
A1
SEATING PLANE
S
NOTES:
PACKAGE
PQR 080
JEDEC
MO-108(B)CB-1
NOTES
1. ALL DIMENSIONS AND TOLERANCES CONFORM TO
ANSI Y14.5M-1982.
SYMBOL
MIN
--
NOM
--
MAX
3.35
--
2. DATUM PLANE -A- IS LOCATED AT THE MOLD PARTING LINE
AND IS COINCIDENT WITH THE BOTTOM OF THE LEAD WHERE
THE LEAD EXITS THE PLASTIC BODY.
A
A1
A2
b
0.25
2.70
0.30
0.15
17.00
13.90
--
--
2.80
--
2.90
0.45
0.23
17.40
14.10
--
3. DIMENSIONS "D1" AND "E1" DO NOT INCLUD MOLD PROTRUSION.
ALLOWABLE PROTRUSION IS 0.25 mm PER SIDE.
SEE NOTE 4
DIMENSIONS "D1" AND "E1" INCLUDE MOLD MISMATCH AND
ARE DETERMINED AT DATUM PLANE -A-
c
--
D
17.20
14.00
12.0
0.80
23.20
20.00
18.40
0.20
0.10
0.88
24
4. DIMENSION "B" DOES NOT INCLUDE DAMBAR PROTRUSION.
5. CONTROLLING DIMENSIONS: MILLIMETER.
D1
D3
e
SEE NOTE 3
REFERENCE
6. DIMENSIONS "D" AND "E" ARE MEASURED FROM BOTH
INNERMOST AND OUTERMOST POINTS.
--
--
BASIC, SEE NOTE 7
7. DEVIATION FROM LEAD-TIP TRUE POSITION SHALL BE WITHIN
±0.0076 mm FOR PITCH > 0.5 mm AND WITHIN ±0.04 FOR
PITCH < 0.5 mm.
E
23.00
19.90
--
23.40
20.10
--
E1
E3
aaa
ccc
L
SEE NOTE 3
REFERENCE
8. LEAD COPLANARITY SHALL BE WITHIN: (REFER TO 06-500)
1 - 0.10 mm FOR DEVICES WITH LEAD PITCH OF 0.65 - 0.80 mm
2 - 0.076 mm FOR DEVICES WITH LEAD PITCH OF 0.50 mm.
COPLANARITY IS MEASURED PER SPECIFICATION 06-500.
---
---
0.73
1.03
9. HALF SPAN (CENTER OF PACKAGE TO LEAD TIP) SHALL BE
WITHIN ±0.0085".
P
Q
40
R
64
S
80
3213\38.4C
Document Number: 002-00948 Rev. *C
Page 10 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
5.3
80-Ball Fortified BGA Connection Diagram
A8
A2
B8
A1
C8
A0
D8
E8
F8
G8
H8
J8
K8
DQ29
VIO
VSS
VIO
DQ20
DQ16
NC
A7
A3
B7
A4
C7
D7
E7
F7
G7
H7
J7
K7
NC
DQ30
DQ26
DQ24
DQ23
DQ18 IND/WAIT#
NC
A6
A6
B6
A5
C6
A7
D6
E6
F6
G6
H6
J6
K6
DQ19
OE#
WE#
DQ31
DQ28
DQ25
DQ21
A5
B5
A8
C5
D5
E5
F5
G5
H5
J5
K5
VSS
NC
NC
DQ27
RY/BY#
DQ22
DQ17
CE#
VCC
A4
B4
A9
C4
D4
E4
F4
G4
H4
J4
K4
ACC
A10
NC
DQ1
DQ5
DQ9
WP#
NC
VSS
A3
B3
C3
D3
E3
F3
G3
H3
J3
K3
VCC
A12
A11
A19
DQ2
DQ6
DQ10
DQ11
ADV#
CLK
A2
B2
C2
D2
E2
F2
G2
H2
J2
K2
A14
A13
A18
DQ0
DQ4
DQ7
DQ8
DQ12
DQ14
RESET#
A1
B1
C1
D1
E1
F1
G1
H1
J1
K1
A15
A16
A17
DQ3
VIO
VSS
VIO
DQ13
DQ15
VIO
Notes
6. On 16 Mb device, ball D3 (A19) is NC.
7. Ball F5 (RY/BY#) is Open Drain and requires an external pull-up resistor.
5.4
Special Package Handling Instructions
Special handling is required for Flash Memory products in molded packages (BGA). The package and/or data integrity may be
compromised if the package body is exposed to temperatures above 150°C for prolonged periods of time.
Document Number: 002-00948 Rev. *C
Page 11 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
5.5
LAA080–80-ball Fortified Ball Grid Array (13 x 11 mm) Physical Dimensions
D1
D
A
0.20
2X
C
eD
K
J
H
G
F
E
D
C
B
A
8
7
6
5
4
3
2
1
7
SE
eE
E
E1
A1 CORNER ID.
(INK OR LASER)
B
A1
CORNER
6
NXφb
SD
0.20
2X
C
7
1.00±0.5
TOP VIEW
φ0.25
φ0.10
M
C
C
A B
A1
CORNER
M
BOTTOM VIEW
0.25
C
A
A2
A1
SEATING PLANE
C
0.15
C
SIDE VIEW
NOTES:
PACKAGE
JEDEC
LAA 080
1. DIMENSIONING AND TOLERANCING METHODS PER
ASME Y14.5M-1994.
N/A
NOTE
13.00 x 11.00 mm
PACKAGE
2. ALL DIMENSIONS ARE IN MILLIMETERS.
3. BALL POSITION DESIGNATION PER JESD 95-1, SPP-010
(EXCEPT AS NOTED).
SYMBOL
A
MIN
--
NOM
--
MAX
1.40
--
PROFILE HEIGHT
STANDOFF
4.
e REPRESENTS THE SOLDER BALL GRID PITCH.
A1
0.40
0.60
--
5. SYMBOL "MD" IS THE BALL ROW MATRIX SIZE IN THE "D"
DIRECTION. SYMBOL "ME" IS THE BALL COLUMN MATRIX
SIZE IN THE "E" DIRECTION. N IS THE TOTAL NUMBER OF
SOLDER BALLS.
A2
--
--
BODY THICKNESS
BODY SIZE
D
13.00 BSC.
11.00 BSC.
9.00 BSC.
7.00 BSC.
10
E
BODY SIZE
6
DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL
DIAMETER IN A PLANE PARALLEL TO DATUM C.
D1
MATRIX FOOTPRINT
MATRIX FOOTPRINT
7
SD AND SE ARE MEASURED WITH RESPECT TO DATUMS A
AND B AND DEFINE THE POSITION OF THE CENTER SOLDER
BALL IN THE OUTER ROW. WHEN THERE IS AN ODD NUMBER
OF SOLDER BALLS IN THE OUTER ROW PARALLEL TO THE D
OR E DIMENSION, RESPECTIVELY, SD OR SE = 0.000.
WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN THE
OUTER ROW , SD OR SE = e/2
E1
MD
ME
N
MATRIX SIZE D DIRECTION
MATRIX SIZE E DIRECTION
BALL COUNT
8
80
φb
0.50
0.60
0.70
BALL DIAMETER
8. N/A
eD
1.00 BSC.
1.00 BSC.
0.50 BSC
BALL PITCH - D DIRECTION
BALL PITCH - E DIRECTION
SOLDER BALL PLACEMENT
9. "+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED
BALLS.
eE
SD/SE
3214\38.12C
Document Number: 002-00948 Rev. *C
Page 12 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
5.6
LAD080–80-ball Fortified Ball Grid Array (11 x 9 mm) Physical Dimensions
NOTES:
1. DIMENSIONING AND TOLERANCING METHODS PER
ASME Y14.5M-1994.
PACKAGE
JEDEC
LAD 080
N/A
2. ALL DIMENSIONS ARE IN MILLIMETERS.
D X E
11.00 mm x 9.00 mm
PACKAGE
3. BALL POSITION DESIGNATION PER JEP95, SECTION
4.3, SPP-010.
SYMBOL
MIN
NOM
---
MAX
NOTE
4.
e REPRESENTS THE SOLDER BALL GRID PITCH.
A
A1
---
1.40
0.55
PROFILE
5. SYMBOL "MD" IS THE BALL MATRIX SIZE IN THE
"D" DIRECTION.
0.35
0.45
BALL HEIGHT
SYMBOL "ME" IS THE BALL MATRIX SIZE IN THE
"E" DIRECTION.
D
11.00 BSC
9.00 BSC
9.00 BSC
7.00 BSC
10
BODY SIZE
E
BODY SIZE
N IS THE NUMBER OF POPULATED SOLDER BALL POSITIONS
FOR MATRIX SIZE MD X ME.
D1
E1
MATRIX FOOTPRINT
MATRIX FOOTPRINT
MATRIX SIZE D DIRECTION
MATRIX SIZE E DIRECTION
BALL COUNT
6
7
DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL
DIAMETER IN A PLANE PARALLEL TO DATUM C.
MD
ME
N
SD AND SE ARE MEASURED WITH RESPECT TO DATUMS
A AND B AND DEFINE THE POSITION OF THE CENTER
SOLDER BALL IN THE OUTER ROW.
8
80
b
0.55
0.65
0.75
BALL DIAMETER
WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN
THE OUTER ROW SD OR SE = 0.000.
eE
1.00 BSC
1.00 BSC
0.50 BSC
N/A
BALL PITCH
WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN
THE OUTER ROW, SD OR SE = e/2
eD
SD / SE
BALL PITCH
SOLDER BALL PLACEMENT
DEPOPULATED SOLDER BALLS
8. “+” INDICATES THE THEORETICAL CENTER OF DEPOPULATED BALLS.
9
A1 CORNER TO BE IDENTIFIED BY CHAMFER, LASER OR INK
MARK, METALLIZED MARK INDENTATION OR OTHER MEANS.
g1064 \ f16-038.12 \ 01.31.12
Document Number: 002-00948 Rev. *C
Page 13 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
6. Product Overview
The S29CD-J and S29CL-J families consist of 32 Mb and 16 Mb, 2.6 volt-only (CD-J) or 3.3 volt-only (CL-J), simultaneous read/
write, dual boot burst mode Flash devices optimized for today's automotive designs.
These devices are organized in 1,048,576 double words (32 Mb) or 524,288 double words (16 Mb) and are capable of linear burst
read (2, 4, or 8 double words) with wraparound. (Note that 1 double word = 32 bits.) These products also offer single word
programming with program/erase suspend and resume functionality. Additional features include:
Advanced Sector Protection methods for protecting sectors as required.
256 bytes of Secured Silicon area for storing customer or factory secured information. The Secured Silicon Sector is One-Time
Programmable.
Electronic marking.
6.1
Memory Map
The S29CD-J and S29CL-J devices consist of two banks organized as shown in Table 1, Table 2, Table 3 and Table 4.
Table 1. S29CD016J/CL016J (Top Boot) Sector and Memory Address Map
x32 Address Range
(A18:A0)
Sector Size
(KDwords)
x32 Address Range
(A18:A0)
Sector Size
(KDwords)
Sector
Sector Group
Sector
Sector Group
SA0 (Note 8)
SA1
SG0
SG1
SG2
SG3
SG4
SG5
SG6
SG7
00000h–007FFh
00800h–00FFFh
01000h–017FFh
01800h–01FFFh
02000h–027FFh
02800h–02FFFh
03000h–037FFh
03800h–03FFFh
04000h–07FFFh
08000h–0BFFFh
0C000h–0FFFFh
10000h–13FFFh
14000h–17FFFh
18000h–1BFFFh
1C000h–1FFFFh
2
2
SA15
SA16
SA17
SA18
SA19
SA20
SA21
SA22
SA23
SA24
SA25
SA26
SA27
SA28
SA29
SA30
SA31
SA32
SA33
SA34
SA35
SA36
SA37
SA38
SA39
SA40
SA41
SA42
SA43
20000h–23FFFh
24000h–27FFFh
28000h–2BFFFh
2C000h–2FFFFh
30000h–33FFFh
34000h–37FFFh
38000h–3BFFFh
3C000h–3FFFFh
40000h–43FFFh
44000h–47FFFh
48000h–4BFFFh
4C000h–4FFFFh
50000h–53FFFh
54000h–57FFFh
58000h–5BFFFh
5C000h–5FFFFh
60000h–63FFFh
64000h–67FFFh
68000h–6BFFFh
6C000h–6FFFFh
70000h–73FFFh
74000h–77FFFh
78000h–7BFFFh
7C000h–7C7FFh
7C800h–7CFFFh
7D000h–7D7FFh
7D800h–7DFFFh
7E000h–7E7FFh
7E800h–7EFFFh
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
2
SG10
SA2
2
SA3
2
SA4
2
SA5
2
SG11
SG12
SG13
SA6
2
SA7
2
SA8
16
16
16
16
16
16
16
SA9
SG8
SA10
SA11
SA12
SA13
SA14
SG9
SG14
SG15
SG16
SG17
SG18
SG19
SG20
SG21
2
2
2
2
2
SA44
SG22
SG23
7F000h–7F7FFh
7F800h–7FFFFh
2
2
(Note 10)
SA45
(Note 10)
Document Number: 002-00948 Rev. *C
Page 14 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Notes
8. Secured Silicon Sector overlays this sector when enabled.
9. The bank address is determined by A18 and A17. BA = 00 for Bank 0 and BA = 01, 10, or 11 for Bank 1.
10. This sector has the additional WP# pin sector protection feature.
Table 2. S29CD016J/CL016J (Bottom Boot) Sector and Memory Address Map
x32
Sector
Group
x32 Address Range Sector Size
Sector
Group
Sector Size
(KDwords)
Sector
Sector
Address Range
(A18:A0)
(A18:A0)
(KDwords)
SA0 (Note 11)
SA1 (Note 11)
SA2
SG0
SG1
SG2
SG3
SG4
SG5
SG6
SG7
00000h–007FFh
00800h–00FFFh
01000h–017FFh
01800h–01FFFh
02000h–027FFh
02800h–02FFFh
03000h–037FFh
03800h–03FFFh
04000h–07FFFh
08000h–0BFFFh
0C000h–0FFFFh
10000h–13FFFh
14000h–17FFFh
18000h–1BFFFh
2
2
SA31
SA32
SA33
SA34
SA35
SA36
SA37
SA38
SA39
SA40
SA41
SA42
SA43
SA44
60000h–63FFFh
64000h–67FFFh
68000h–6BFFFh
6C000h–6FFFFh
70000h–73FFFh
74000h–77FFFh
78000h–7BFFFh
7C000h–7C7FFh
7C800h–7CFFFh
7D000h–7D7FFh
7D800h–7DFFFh
7E000h–7E7FFh
7E800h–7EFFFh
7F000h–7F7FFh
16
16
16
16
16
16
16
2
SG14
2
SA3
2
SA4
2
SA5
2
SG15
SA6
2
SA7
2
SG16
SG17
SG18
SG19
SG20
SG21
SG22
SA8
16
16
16
16
16
16
2
SA9
SG8
2
SA10
2
SA11
2
SA12
2
SG9
SA13
2
SA45
(Note 13)
SA14
1C000h–1FFFFh
16
SG23
7F800h–7FFFFh
2
SA15
SA16
SA17
SA18
SA19
SA20
SA21
SA22
SA23
SA24
SA25
SA26
SA27
SA28
SA29
SA30
20000h–23FFFh
24000h–27FFFh
28000h–2BFFFh
2C000h–2FFFFh
30000h–33FFFh
34000h–37FFFh
38000h–3BFFFh
3C000h–3FFFFh
40000h–43FFFh
44000h–47FFFh
48000h–4BFFFh
4C000h–4FFFFh
50000h–53FFFh
54000h–57FFFh
58000h–5BFFFh
5C000h–5FFFFh
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
SG10
SG11
SG12
SG13
Notes
11. This sector has the additional WP# pin sector protection feature.
12. The bank address is determined by A18 and A17. BA = 00, 01, or 10 for Bank 0 and BA = 11 for Bank 1.
13. Secured Silicon Sector overlays this sector when enabled.
Document Number: 002-00948 Rev. *C
Page 15 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Table 3. S29CD032J/CL032J (Top Boot) Sector and Memory Address Map
x32 Address Range
(A19:A0)
Sector Size
(KDwords)
x32 Address Range
(A19:A0)
Sector Size
(KDwords)
Sector
Sector Group
Sector
Sector Group
Bank 0 (Note 15)
Bank 1 continued (Note 15)
80000h–83FFFh
SA0
(Note 14)
SG0
00000h–007FFh
2
SA39
16
SA1
SA2
SG1
SG2
SG3
SG4
SG5
SG6
SG7
00800h–00FFFh
01000h–017FFh
01800h–01FFFh
02000h–027FFh
02800h–02FFFh
03000h–037FFh
03800h–03FFFh
04000h–07FFFh
08000h–0BFFFh
0C000h–0FFFFh
10000h–13FFFh
14000h–17FFFh
18000h–1BFFFh
1C000h–1FFFFh
20000h–23FFFh
24000h–27FFFh
28000h–2BFFFh
2C000h–2FFFFh
30000h–33FFFh
34000h–37FFFh
38000h–3BFFFh
3C000h–3FFFFh
2
SA40
SA41
SA42
SA43
SA44
SA45
SA46
SA47
SA48
SA49
SA50
SA51
SA52
SA53
SA54
SA55
SA56
SA57
SA58
SA59
SA60
SA61
SA62
SA63
SA64
SA65
SA66
SA67
SA68
SA69
SA70
SA71
SA72
SA73
SA74
84000h–87FFFh
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
2
SG16
2
88000h–8BFFFh
8C000h–8FFFFh
90000h–93FFFh
94000h–97FFFh
98000h–9BFFFh
9C000h–9FFFFh
A0000h–A3FFFh
A4000h–A7FFFh
A8000h–ABFFFh
AC000h–AFFFFh
B0000h–B3FFFh
B4000h–B7FFFh
B8000h–BBFFFh
BC000h–BFFFFh
C0000h–C3FFFh
C4000h–C7FFFh
C8000h–CBFFFh
CC000h–CFFFFh
D0000h–D3FFFh
D4000h–D7FFFh
D8000h–DBFFFh
DC000h–DFFFFh
E0000h–E3FFFh
E4000h–E7FFFh
E8000h–EBFFFh
EC000h–EFFFFh
F0000h–F3FFFh
F4000h–F7FFFh
F8000h–FBFFFh
FC000h–FC7FFh
FC800h–FCFFFh
FD000h–FD7FFh
FD800h–FDFFFh
FE000h–FE7FFh
SA3
2
SA4
2
SA5
2
SG17
SG18
SG19
SG20
SG21
SA6
2
SA7
2
SA8
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
SA9
SG8
SA10
SA11
SA12
SA13
SA14
SA15
SA16
SA17
SA18
SA19
SA20
SA21
SA22
SG9
SG10
SG11
Bank 1 (Note 15)
SA23
SA24
SA25
SA26
SA27
SA28
SA29
SA30
SA31
SA32
SA33
SA34
40000h–43FFFh
44000h–47FFFh
48000h–4BFFFh
4C000h–4FFFFh
50000h–53FFFh
54000h–57FFFh
58000h–5BFFFh
5C000h–5FFFFh
60000h–63FFFh
64000h–67FFFh
68000h–6BFFFh
6C000h–6FFFFh
16
16
16
16
16
16
16
16
16
16
16
16
SG12
SG13
SG14
SG22
SG23
SG24
SG25
SG26
SG27
SG28
2
2
2
2
Document Number: 002-00948 Rev. *C
Page 16 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Table 3. S29CD032J/CL032J (Top Boot) Sector and Memory Address Map (Continued)
x32 Address Range
(A19:A0)
Sector Size
(KDwords)
x32 Address Range
(A19:A0)
Sector Size
(KDwords)
Sector
Sector Group
Sector
Sector Group
Bank 0 (Note 15)
Bank 1 continued (Note 15)
SA35
SA36
70000h–73FFFh
74000h–77FFFh
16
16
SA75
SG29
FE800h–FEFFFh
FF000h–FF7FFh
2
2
SA76
(Note 16)
SG30
SG31
SG15
SA77
(Note 16)
SA37
SA38
78000h–7BFFFh
7C000h–7FFFFh
16
16
FF800h–FFFFFh
2
Notes
14. Secured Silicon Sector overlays this sector when enabled.
15. The bank address is determined by A19 and A18. BA = 00 for Bank 0 and BA = 01, 10, or 11 for Bank 1.
16. This sector has the additional WP# pin sector protection feature.
Document Number: 002-00948 Rev. *C
Page 17 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Table 4. S29CD032J/CL032J (Bottom Boot) Sector and Memory Address Map
Sector Size
(KDwords)
x32 Address Range
(A19:A0)
Sector Size
(KDwords)
x32 Address Range
(A19:A0)
Sector
Sector Group
Sector
Sector Group
Bank 0 (Note 18)
Bank 0 continued (Note 18)
SA0 (Note 19)
SA1 (Note 19)
SA2
SG0
SG1
SG2
SG3
SG4
SG5
SG6
SG7
00000h–007FFh
00800h–00FFFh
01000h–017FFh
01800h–01FFFh
02000h–027FFh
02800h–02FFFh
03000h–037FFh
03800h–03FFFh
04000h–07FFFh
08000h–0BFFFh
0C000h–0FFFFh
10000h–13FFFh
14000h–17FFFh
18000h–1BFFFh
1C000h–1FFFFh
20000h–23FFFh
24000h–27FFFh
28000h–2BFFFh
2C000h–2FFFFh
30000h–33FFFh
34000h–37FFFh
38000h–3BFFFh
3C000h–3FFFFh
40000h–43FFFh
44000h–47FFFh
48000h–4BFFFh
4C000h–4FFFFh
50000h–53FFFh
54000h–57FFFh
58000h–5BFFFh
5C000h–5FFFFh
60000h–63FFFh
64000h–67FFFh
68000h–6BFFFh
6C000h–6FFFFh
70000h–73FFFh
74000h–77FFFh
78000h–7BFFFh
7C000h–7FFFFh
2
SA39
SA40
SA41
SA42
SA43
SA44
SA45
SA46
SA47
SA48
SA49
SA50
SA51
SA52
SA53
SA54
80000h–83FFFh
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
2
84000h–87FFFh
SG16
2
88000h–8BFFFh
SA3
2
8C000h–8FFFFh
90000h–93FFFh
SA4
2
SA5
2
94000h–97FFFh
SG17
SA6
2
98000h–9BFFFh
SA7
2
9C000h–9FFFFh
A0000h–A3FFFh
SA8
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
SA9
SG8
A4000h–A7FFFh
SG18
SA10
SA11
SA12
SA13
SA14
SA15
SA16
SA17
SA18
SA19
SA20
SA21
SA22
SA23
SA24
SA25
SA26
SA27
SA28
SA29
SA30
SA31
SA32
SA33
SA34
SA35
SA36
SA37
SA38
A8000h–ABFFFh
AC000h–AFFFFh
B0000h–B3FFFh
SG9
B4000h–B7FFFh
SG19
B8000h–BBFFFh
BC000h–BFFFFh
Bank 1 (Note 18)
SG10
SG11
SG12
SG13
SG14
SG15
SA55
SA56
C0000h–C3FFFh
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
2
C4000h–C7FFFh
SG20
SA57
C8000h–CBFFFh
SA58
CC000h–CFFFFh
D0000h–D3FFFh
SA59
SA60
D4000h–D7FFFh
SG21
SA61
D8000h–DBFFFh
SA62
DC000h–DFFFFh
E0000h–E3FFFh
SA63
SA64
E4000h–E7FFFh
SG22
SA65
E8000h–EBFFFh
SA66
EC000h–EFFFFh
F0000h–F3FFFh
SA67
SA68
SG23
F4000h–F7FFFh
F8000h–FBFFFh
FC000h–FC7FFh
FC800h–FCFFFh
FD000h–FD7FFh
FD800h–FDFFFh
FE000h–FE7FFh
FE800h–FEFFFh
FF000h–FF7FFh
FF800h–FFFFFh
SA69
SA70
SG24
SG25
SG26
SG27
SG28
SG29
SG30
SG31
SA71
2
SA72
2
SA73
2
SA74
2
SA75
2
SA76
2
SA77 (Note 17)
2
Notes
17. This sector has the additional WP# pin sector protection feature.
18. The bank address is determined by A19 and A18. BA = 00, 01, or 10 for Bank 0 and BA = 11 for Bank 1.
19.The Secured Silicon Sector overlays this sector when enabled.
Document Number: 002-00948 Rev. *C
Page 18 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
7. Device Operations
This section describes the read, program, erase, simultaneous read/write operations, and reset features of the Flash devices.
Operations are initiated by writing specific commands or a sequence with specific address and data patterns into the command
register (see Table 5). The command register itself does not occupy any addressable memory location; rather, it is composed of
latches that store the commands, along with the address and data information needed to execute the command. The contents of the
register serve as input to the internal state machine; the state machine outputs dictate the function of the device. Writing incorrect
address and data values or writing them in an improper sequence may place the device in an unknown state, in which case the
system must write the reset command in order to return the device to the reading array data mode.
7.1
Device Operation Table
The device must be set up appropriately for each operation. Table 5 describes the required state of each control pin for any
particular operation.
Table 5. Device Bus Operation
Data
(DQ0–DQ31)
Operation
CE# OE# WE# RESET#
CLK
ADV#
Addresses
Read
L
L
L
H
L
H
H
X
X
X
X
AIN
AIN
DOUT
Asynchronous Write
Synchronous Write
H
DIN
L
H
L
H
AIN
DIN
Standby (CE#)
Output Disable
Reset
H
L
X
H
X
X
H
X
H
H
L
H
X
X
X
X
X
X
High-Z
X
High-Z
High-Z
High-Z
X
00000001h, (protected)
A6 = H
Sector Address,
A9 = VID,
A7 – A0 = 02h
PPB Protection Status (Note 2)
L
L
H
H
X
X
00000000h (unprotect)
A6 = L
Burst Read Operations
Load Starting Burst Address
L
L
X
L
H
H
H
H
AIN
X
X
Advance Burst to next address
with appropriate Data presented
on the Data bus
H
Burst Data Out
Terminate Current Burst Read Cycle
H
X
L
X
X
H
H
H
H
H
L
X
X
X
X
High-Z
High-Z
X
Terminate Current Burst
Read Cycle with RESET#
X
Terminate Current Burst Read Cycle;
Start New Burst Read Cycle
H
AIN
Legend
L = Logic Low = V , H = Logic High = V , X = Don’t care.
IL
IH
Notes
20. WP# controls the two outermost sectors of the top boot block or the two outermost sectors of the bottom boot block.
21.DQ0 reflects the sector PPB (or sector group PPB) and DQ1 reflects the DYB.
Document Number: 002-00948 Rev. *C
Page 19 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
7.2
Asynchronous Read
All memories require access time to output array data. In an asynchronous read operation, data is read from one memory location at
a time. Addresses are presented to the device in random order, and the propagation delay through the device causes the data on its
outputs to arrive asynchronously with the address on its inputs.
The internal state machine is set for asynchronously reading array data upon device power-up, or after a hardware reset. This
ensures that no spurious alteration of the memory content occurs during the power transition. No command is necessary in this
mode to obtain array data. Standard microprocessor read cycles that assert valid addresses on the device address inputs produce
valid data on the device data outputs. The device remains enabled for read access until the command register contents are altered.
The device has two control functions which must be satisfied in order to obtain data at the outputs. CE# is the power control and
should be used for device selection (CE# must be set to VIL to read data). OE# is the output control and should be used to gate data
to the output pins if the device is selected (OE# must be set to VIL in order to read data). WE# should remain at VIH (when reading
data).
Address access time (tACC) is equal to the delay from stable addresses to valid output data. The chip enable access time (tCE) is the
delay from the stable addresses and stable CE# to valid data at the output pins. The output enable access time (tOE) is the delay
from the falling edge of OE# to valid data at the output pins (assuming the addresses have been stable for at least a period of tACC
tOE and CE# has been asserted for at least tCE-tOE time). Figure 1 shows the timing diagram of an asynchronous read operation.
-
Figure 1. Asynchronous Read Operation
CE#
CLK
ADV#
Addresses
Data
Address 0
Address 1
Address 2
Address 3
D0
D1
D2
D3
D3
OE#
WE#
VIH
Float
Float
VOH
IND/WAIT#
Note
22.Operation is shown for the 32-bit data bus. For the 16-bit data bus, A-1 is required.
Refer to Asynchronous Operations on page 52 for timing specifications and to Figure 19 Conventional Read Operations Timings
on page 53 for another timing diagram. ICC1 in the DC Characteristics table represents the active current specification for reading
array data.
Document Number: 002-00948 Rev. *C
Page 20 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
7.3
Hardware Reset (RESET#)
The RESET# pin is an active low signal that is used to reset the device under any circumstances. A logic “0” on this input forces the
device out of any mode that is currently executing back to the reset state. RESET# may be tied to the system reset circuitry. A
system reset would thus also reset the device. To avoid a potential bus contention during a system reset, the device is isolated from
the DQ data bus by tristating the data outputs for the duration of the RESET pulse. All data outputs are “don’t care” during the reset
operation.
If RESET# is asserted during a program or erase operation, the RY/BY# output remains low until the reset operation is internally
complete. The RY/BY# pin can be used to determine when the reset operation is complete. Since the device offers simultaneous
read/write operation, the host system may read a bank after a period of tREADY2, if the bank was in the read/reset mode at the time
RESET# was asserted. If one of the banks was in the middle of either a program or erase operation when RESET# was asserted,
the user must wait a period of tREADY before accessing that bank.
Asserting RESET# during a program or erase operation leaves erroneous data stored in the address locations being operated on at
the time of device reset. These locations need updating after the reset operation is complete. See Hardware Reset (RESET#)
on page 56 for timing specifications.
Asserting RESET# active during VCC and VIO power-up is required to guarantee proper device initialization until VCC and VIO have
reached their steady state voltages. See VCC and VIO Power-up on page 52.
7.4
Synchronous (Burst) Read Mode and Configuration Register
When a series of adjacent addresses need to be read from the device, the synchronous (or burst read) mode can be used to
significantly reduce the overall time needed for the device to output array data. After an initial access time required for the data from
the first address location, subsequent data is output synchronized to a clock input provided by the system.
The device offers a linear method of burst read operation which is discussed in 2-, 4-, 8- Double Word Linear Burst Operation
on page 22.
Since the device defaults to asynchronous read mode after power-up or a hardware reset, the configuration register must be set in
order to enable the burst read mode. Other Configuration Register settings include the number of wait states to insert before the
initial word (tIACC) of each burst access and when RDY indicates that data is ready to be read. Prior to entering the burst mode, the
system first determines the configuration register settings (and read the current register settings if desired via the Read
Configuration Register command sequence), then write the configuration register command sequence. See Configuration Register
on page 24, and Table 34 on page 67 for further details. Once the configuration register is written to enable burst mode operation,
all subsequent reads from the array are returned using the burst mode protocols.
Figure 2. Synchronous/Asynchronous State Diagram
Power-up/
Hardware Reset
Asynchronous Read
Mode Only
Set Burst Mode
Configuration Register
Command for
Set Burst Mode
Configuration Register
Command for
Synchronous Mode
(D15 = 0)
Asynchronous Mode
(D15 = 1)
Synchronous Read
Mode Only
Document Number: 002-00948 Rev. *C
Page 21 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
The device outputs the initial word subject to the following operational conditions:
tIACC specification: The time from the rising edge of the first clock cycle after addresses are latched to valid data on the device
outputs.
Configuration register setting CR13-CR10: The total number of clock cycles (wait states) that occur before valid data appears on
the device outputs. The effect is that tIACC is lengthened.
Like the main memory access, the Secured Silicon Sector memory is accessed with the same burst or asynchronous timing as
defined in the Configuration Register. However, the user must recognize burst operations past the 256 byte Secured Silicon
boundary returns invalid data.
Burst read operations occur only to the main flash memory arrays. The Configuration Register and protection bits are treated as
single cycle reads, even when burst mode is enabled. Read operations to these locations results in the data remaining valid while
OE# is at VIL, regardless of the number of CLK cycles applied to the device.
7.4.1 2-, 4-, 8- Double Word Linear Burst Operation
In a linear burst read operation, a fixed number of words (2, 4, or 8 double words) are read from consecutive addresses that are
determined by the group within which the starting address falls. Note that 1 double word = 32 bits. See Table 6 for all valid burst
output sequences.
The IND/WAIT# signal, or End of Burst Indicator signal, transitions active (VIL) during the last transfer of data in a linear burst read
before a wrap around. This transition indicates that the system should initiate another ADV# to start the next burst access. If the
system continues to clock the device, the next access wraps around to the starting address of the previous burst access. The IND/
WAIT# signal is floating when not active.
Table 6. 32-Bit Linear and Burst Data Order
Data Transfer Sequence
Output Data Sequence (Initial Access Address)
0-1 (A0 = 0)
1-0 (A0 = 1)
Two Linear Data Transfers
0-1-2-3 (A1-A0 = 00)
1-2-3-0 (A1-A0 = 01)
2-3-0-1 (A1-A0 = 10)
3-0-1-2 (A1-A0 = 11)
Four Linear Data Transfers
Eight Linear Data Transfers
0-1-2-3-4-5-6-7 (A2-A0 = 000)
1-2-3-4-5-6-7-0 (A2-A0 = 001)
2-3-4-5-6-7-0-1 (A2-A0 = 010)
3-4-5-6-7-0-1-2 (A2-A0 = 011)
4-5-6-7-0-1-2-3 (A2-A0 = 100)
5-6-7-0-1-2-3-4 (A2-A0 = 101)
6-7-0-1-2-3-4-5 (A2-A0 = 110)
7-0-1-2-3-4-5-6 (A2-A0 = 111)
Notes
23. The default configuration in the Control Register for Bit 6 is “1,” indicating that the device delivers data on the rising edge of the CLK signal.
24.The device is capable of holding data for one CLK cycle.
25. If RESET# is asserted low during a burst access, the burst access is immediately terminated and the device defaults back to asynchronous read mode. When this
happens, the DQ data bus signal floats and the Configuration Register contents are reset to their default conditions.
26. CE# must meet the required burst read setup times for burst cycle initiation. If CE# is taken to V at any time during the burst linear or burst cycle, the device
IH
immediately exits the burst sequence and floats the DQ bus signal.
27.Restarting a burst cycle is accomplished by taking CE# and ADV# to V
.
IL
28.A burst access is initiated and the address is latched on the first rising CLK edge when ADV# is active or upon a rising ADV# edge, whichever occurs first. If the ADV#
signal is taken to VIL prior to the end of a linear burst sequence, the previous address is discarded and subsequent burst transfers are invalid. A new burst is initiated
when ADV# transitions back to V before a clock edge.
IH
29. The OE# (Output Enable) pin is used to enable the linear burst data on the DQ data bus pin. De-asserting the OE# pin to V during a burst operation floats the data
IH
bus, but the device continues to operate internally as if the burst sequence continues until the linear burst is complete. The OE# pin does not halt the burst sequence,
The DQ bus remains in the float state until OE# is taken to V
.
IL
30.Halting the burst sequence is accomplished by either taking CE# to V or re-issuing a new ADV# pulse.
IH
Document Number: 002-00948 Rev. *C
Page 22 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
The IND/WAIT# signal is controlled by the OE# signal. If OE# is at VIH, the IND/WAIT# signal floats and is not driven. If OE# is at
VIL, the IND/ WAIT# signal is driven at VIH until it transitions to VIL, indicating the end of the burst sequence. Table 7 lists the valid
combinations of the Configuration Register bits that impact the IND/WAIT# timing. See Figure 3 for the IND/WAIT# timing diagram.
Table 7. Valid Configuration Register Bit Definition for IND/WAIT#
CR9 (DOC)
CR8 (WC) CR6 (CC)
Definition
IND/WAIT# = VIL for 1-CLK cycle, Active on last transfer, Driven on rising CLK edge
IND/WAIT# = VIL for 1-CLK cycle, Active on second to last transfer, Driven on rising CLK edge
0
0
0
1
1
1
Figure 3. End of Burst Indicator (IND/WAIT#) Timing for Linear 4 Double Word Burst Operation
V
IH
CE#
CLK
V
IL
3 Clock Delay
ADV#
Addresses
Data
Address 1 Latched
Address 2
Address 1
Invalid
D1
D2
D3
D0
OE#
IND/WAIT#
Note
31.Operation is shown for the 32-bit data bus. Figure shown with 3-CLK initial access delay configuration, linear address, 4-doubleword burst, output on rising CLK edge,
data hold for 1-CLK, IND/WAIT# asserted on the last transfer before wrap-around.
7.4.2 Initial Burst Access Delay
Initial Burst Access Delay is defined as the number of clock cycles that must elapse from the first valid clock edge after ADV#
assertion (or the rising edge of ADV#) until the first valid CLK edge when the data is valid. Burst access is initiated and the address
is latched on the first rising CLK edge when ADV# is active or upon a rising ADV# edge, whichever comes first. The Initial Burst
Access Delay is determined in the Configuration Register (CR13-CR10). Refer to Table 9 for the initial access delay configurations
under CR13-CR10. See Figure 4 for the Initial Burst Delay Control timing diagram. Note that the Initial Access Delay for a burst
access has no effect on asynchronous read operations.
Table 8. Burst Initial Access Delay
CR13
CR12
CR11
CR10
Initial Burst Access (CLK cycles)
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
1
1
0
0
1
1
1
0
1
0
1
0
1
3
4
5
6
7
8
9
Document Number: 002-00948 Rev. *C
Page 23 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Figure 4. Initial Burst Delay Control
1st CLK
2nd CLK
3rd CLK
4th CLK
5th CLK
CLK
ADV#
Address 1 Latched
Valid Address
Addresses
Three CLK Delay
DQ31-DQ03
DQ31-DQ04
D0
D1
D0
D2
D1
D3
D2
D4
D3
Four CLK Delay
Five CLK Delay
DQ31-DQ05
D0
D1
D2
Notes
32.Burst access starts with a rising CLK edge and when ADV# is active.
33. Configurations register 6 is always set to 1 (CR6 = 1). Burst starts and data outputs on the rising CLK edge.
34.CR [13-10] = 1 or three clock cycles.
35.CR [13-10] = 2 or four clock cycles.
36. CR [13-10] = 3 or five clock cycles.
7.4.3 Configuration Register
The configuration register sets various operational parameters associated with burst mode. Upon power-up or hardware reset, the
device defaults to the asynchronous read mode and the configuration register settings are in their default state. (See Table 10 for
the default Configuration Register settings.) The host system determines the proper settings for the entire configuration register, and
then execute the Set Configuration Register command sequence before attempting burst operations. The configuration register is
not reset after deasserting CE#.
The Configuration Register does not occupy any addressable memory location, but rather, is accessed by the Configuration
Register commands. The Configuration Register is readable at any time, however, writing the Configuration Register is restricted to
times when the Embedded Algorithm™ is not active. If the user attempts to write the Configuration Register while the Embedded
Algorithm is active, the write operation is ignored and the contents of the Configuration Register remain unchanged.
The Configuration Register is a 16 bit data field which is accessed by DQ15–DQ0. During a read operation, DQ31–DQ16 returns all
zeroes. Also, the Configuration Register reads operate the same as the Autoselect command reads. When the command is issued,
the bank address is latched along with the command. Read operations to the bank that was specified during the Configuration
Register read command return Configuration Register contents. Read operations to the other bank return flash memory data. Either
bank address is permitted when writing the Configuration Register read command.
The configuration register can be read with a four-cycle command sequence. See Command Definitions on page 67 for sequence
details.
Document Number: 002-00948 Rev. *C
Page 24 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Table 9 describes the Configuration Register settings.
Table 9. Configuration Register
Configuration Register
CR15 = Read Mode (RM)
0 = Synchronous Burst Reads Enabled
1 = Asynchronous Reads Enabled (Default)
CR14 = Reserved for Future Enhancements
These bits are reserved for future use. Set these bits to 0.
CR13–CR10 = Initial Burst Access Delay Configuration (IAD3-IAD0)
0000 = 2 CLK cycle initial burst access delay
0001 = 3 CLK cycle initial burst access delay
0010 = 4 CLK cycle initial burst access delay
0011 = 5 CLK cycle initial burst access delay
0100 = 6 CLK cycle initial burst access delay
0101 = 7 CLK cycle initial burst access delay
0110 = 8 CLK cycle initial burst access delay
0111 = 9 CLK cycle initial burst access delay—Default
CR9 = Data Output Configuration (DOC)
0 = Hold Data for 1-CLK cycle—Default
1 = Reserved
CR8 = IND/WAIT# Configuration (WC)
0 = IND/WAIT# Asserted During Delay—Default
1 = IND/WAIT# Asserted One Data Cycle Before Delay
CR7 = Burst Sequence (BS)
0 = Reserved
1 = Linear Burst Order—Default
CR6 = Clock Configuration (CC)
0 = Reserved
1 = Burst Starts and Data Output on Rising Clock Edge—Default
CR5–CR3 = Reserved For Future Enhancements (R)
These bits are reserved for future use. Set these bits to 0.
CR2–CR0 = Burst Length (BL2–BL0)
000 = Reserved, burst accesses disabled (asynchronous reads only)
001 = 64 bit (8-byte) Burst Data Transfer - x32 Linear
010 = 128 bit (16-byte) Burst Data Transfer - x32 Linear
011 = 256 bit (32-byte) Burst Data Transfer - x32 Linear (device default)
100 = Reserved, burst accesses disabled (asynchronous reads only)
101 = Reserved, burst accesses disabled (asynchronous reads only)
110 = Reserved, burst accesses disabled (asynchronous reads only)
Table 10. Configuration Register After Device Reset
CR15
RM
1
CR14
Reserve
0
CR13
IAD3
0
CR12
IAD2
1
CR11
IAD1
1
CR10
IAD0
1
CR9
DOC
0
CR8
Reserve
0
CR7
BS
1
CR6
CC
1
CR5
Reserve
0
CR4
Reserve
0
CR3
Reserve
0
CR2
BL2
1
CR1
BL1
0
CR0
BL0
0
Document Number: 002-00948 Rev. *C
Page 25 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
7.5
Autoselect
The autoselect mode provides manufacturer and device identification, and sector protection verification, through identifier codes
output on DQ7–DQ0. This mode is primarily intended for programming equipment to automatically match a device to be
programmed with its corresponding programming algorithm. However, the autoselect codes can also be accessed in-system
through the command register.
When using programming equipment, the autoselect mode requires VID on address pin A9. Ad-dress pins A6, A1, and A0 must be
as shown in Table 11. In addition, when verifying sector protection, the sector address must appear on the appropriate highest order
address bits. Table 11 shows the remaining address bits that are don’t care. When all necessary bits have been set as required, the
programming equipment may then read the corresponding identifier code on DQ7–DQ0.
To access the autoselect codes in-system, the host system can issue the autoselect command via the command. This method does
not require VID. See Command Definitions on page 67 for details on using the autoselect mode. Autoselect mode can be used in
either synchronous (Burst) mode or asynchronous (Non Burst) mode.
The system must write the reset command to exit the autoselect mode and return to reading the array data. See Table 11 for
command sequence details.
Table 11. S29CD-J and S29CL-J Flash Family Autoselect Codes (High Voltage Method)
Description
CE# OE# WE# A19 to A11 A10 A9 A8 A7 A6 A5 to A4 A3 A2 A1 A0
DQ7 to DQ0
Manufacturer ID: Cypress
L
L
L
L
H
H
X
X
X
X
VID
VID
X
X
X
L
L
L
X
X
X
L
X
L
L
L
L
0001h
007Eh
Read Cycle 1
H
08h or 36h for CD016J
46h for CL016J
Read Cycle 2
Read Cycle 3
L
L
H
X
X
VID
X
L
L
L
H
H
H
L
09h for CD032J
49h for CL032J
0000h
Top Boot Option
L
L
L
L
H
H
X
X
X
VID
X
X
L
L
L
L
L
L
H
L
H
L
H
H
H
L
0001h
Bottom Boot Option
0000h (unprotected)
0001h (protected)
PPB Protection Status
SA
VID
Legend
L = Logic Low = V , H = Logic High = V , SA = Sector Address, X = Don’t care.
IL
IH
Note
37.The autoselect codes can also be accessed in-system via command sequences. See Table 35.
Document Number: 002-00948 Rev. *C
Page 26 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
7.6
VersatileI/O (V ) Control
IO
The VersatileI/O (VIO) control allows the host system to set the voltage levels that the device generates at its data outputs and the
voltages tolerated at its data inputs to the same voltage level that is asserted on the VIO pin. The output voltage generated on the
device is determined based on the VIO level. For the 2.6 V (CD-J), a VIO of 1.65 V–3.6 V (CD032J has a VIO of 1.65 V to 2.75 V)
allows the device to interface with I/Os lower than 2.5 V. For a 3.3 V VCC (CL-J), a VIO of 1.65 V–3.60 V allows the device to
interface with I/Os lower than 3.0 V.
7.7
Program/Erase Operations
These devices are capable of several modes of programming and or erase operations which are described in detail in the following
sections. However, prior to any programming and or erase operation, devices must be set up appropriately as outlined in the
configuration register (see Table 9 on page 25). During a synchronous write operation, to write a command or command sequence
(including programming data to the device and erasing sectors of memory), the system must drive ADV# and CE# to VIL, and OE# to
VIH when providing an address to the device, and drive WE# and CE# to VIL, and OE# to VIH when writing commands or
programming data.
7.7.1 Programming
Programming is a four-bus-cycle operation. The program command sequence is initiated by writing two unlock write cycles, followed
by the program setup command. The program address and data are written next, which in turn initiate the Embedded Program
algorithm. The system is not required to provide further controls or timings. The device automatically generates the program pulses
and verifies the programmed cell margin. Command Definitions on page 67 shows the address and data requirements for the
program command sequence.
Note the following:
When the Embedded Program algorithm is complete, the device returns to the read mode and address are no longer latched. An
address change is required to begin reading valid array data.
The system can determine the status of the program operation by using DQ7, DQ6 or RY/BY#. Refer to Write Operation Status
on page 32 for information on these status bits.
A “0” cannot be programmed back to a “1.” Attempting to do so may halt the operation and set DQ5 to 1, or cause the Data#
Polling algorithm to indicate the operation was successful. A succeeding read shows that the data is still “0.” Only erase operations
can convert a “0” to a “1.”
Any commands written to the device during the Embedded Program Algorithm are ignored except the Program Suspend
command.
A hardware reset immediately terminates the program operation; the program command sequence should be re-initiated once the
device has returned to the read mode, to ensure data integrity.
For the 32Mb S29CD-J and S29CL-J devices only:
Refer to the application note “Recommended Mode of Operation for Cypress® 110 nm S29CD032J/S29CL032J Flash Memory”
publication number S29CD-CL032J_Recommend_AN for programming best practices.
Document Number: 002-00948 Rev. *C
Page 27 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Figure 5. Program Operation
START
Write Program
Command Sequence
Data Poll
from System
Embedded
Program
algorithm
in progress
Verify Data?
Yes
No
No
Increment Address
Last Address?
Yes
Programming
Completed
Note
38.See Table 30 and Table 35 for program command sequence.
7.7.2 Sector Erase
The sector erase function erases one or more sectors in the memory array. (See Table 34. Memory Array Command Definitions
(x32 Mode) on page 67 and Figure 6 Erase Operation on page 29.) The device does not require the system to preprogram prior to
erase. The Embedded Erase algorithm automatically programs and verifies the entire memory for an all-zero data pattern prior to
electrical erase. After a successful sector erase, all locations within the erased sector contain FFFFh. The system is not required to
provide any controls or timings during these operations.
After the command sequence is written, a sector erase time-out of no less than 80 µs occurs. During the time-out period, additional
sector addresses and sector erase commands may be written. Loading the sector erase buffer may be done in any sequence, and
the number of sectors may be from one sector to all sectors. The time between these additional cycles must be less than 80 µs. Any
sector erase address and command following the exceeded time-out (80 µs) may or may not be accepted. A time-out of 80 µs from
the rising edge of the last WE# (or CE#) initiates the execution of the Sector Erase command(s). If another falling edge of the WE#
(or CE#) occurs within the 80 µs time-out window, the timer is reset. Any command other than Erase Suspend during the time-out
period will be interpreted as an additional sector to erase. The device does not decode the data bus, but latches the address. (See
S29CD016J Sector Erase Time-Out Functionality Application Note for further information.). The system can monitor DQ3 to
determine if the sector erase timer has timed out (See DQ3: Sector Erase Timer on page 35.) The time-out begins from the rising
edge of the final WE# pulse in the command sequence.
When the Embedded Erase algorithm is complete, the bank returns to reading array data; addresses are no longer latched. The
system can determine the status of the erase operation by reading DQ7 or DQ6/DQ2 in the erasing bank. Refer to Write Operation
Status on page 32 for information on these status bits.
Once the sector erase operation has begun, only the Erase Suspend command is valid. All other commands are ignored. However,
note that a hardware reset immediately terminates the erase operation. If that occurs, the sector erase command sequence should
be re-initiated once that bank has returned to reading array data, in order to ensure data integrity.
Figure 6 on page 29 illustrates the algorithm for the erase operation. Refer to Program/Erase Operations on page 27 for parameters
and timing diagrams.
Document Number: 002-00948 Rev. *C
Page 28 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
7.7.3 Chip Erase
Chip erase is a six-bus cycle operation as indicated by Command Definitions on page 67. The Chip Erase command is used to
erase the entire flash memory contents of the chip by issuing a single command. However, chip erase does not erase protected
sectors.
This command invokes the Embedded Erase algorithm, which does not require the system to preprogram prior to erase. The
Embedded Erase algorithm automatically preprograms and verifies the entire memory for an all-zero data pattern prior to electrical
erase. After a successful chip erase, all locations of the chip contain FFFFh. The system is not required to provide any controls or
timings during these operations. Command Definitions on page 67 in the appendix shows the address and data requirements for the
chip erase command sequence.
When the Embedded Erase algorithm is complete, that bank returns to the read mode and addresses are no longer latched. The
system can determine the status of the erase operation by using DQ7, DQ6 or the RY/BY#. Refer to Write Operation Status
on page 32 for information on these status bits.
Any commands written during the chip erase operation are ignored. However, note that a hardware reset immediately terminates the
erase operation. If that occurs, the chip erase command sequence should be reinitiated once that bank has returned to reading array
data, to ensure data integrity.
Figure 6. Erase Operation
START
Write Erase
Command Sequence
Data Poll
from System
Embedded
Erase
algorithm
in progress
No
Data = FFh?
Yes
Erasure Completed
Notes
39.See Command Definitions on page 67 for erase command sequence.
40.See DQ3: Sector Erase Timer on page 35 for more information.
Document Number: 002-00948 Rev. *C
Page 29 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
7.7.4 Erase Suspend / Erase Resume Commands
The Erase Suspend command allows the system to interrupt a sector erase operation and then read data from, or program data to,
any sector not selected for erasure. When the Erase Suspend command is written during the sector erase time-out, the device
immediately terminates the time-out period and suspends the erase operation. The bank address is required when writing this
command. This command is valid only during the sector erase operation, including the minimum 80-µs time-out period during the
sector erase command sequence. The Erase Suspend command is ignored if written during the chip erase operation.
When the Erase Suspend command is written after the 80-µs time-out period has expired and during the sector erase operation, the
device takes 20 µs maximum to suspend the erase operation.
After the erase operation has been suspended, the bank enters the erase-suspend-read mode. The system can read data from or
program data to any sector that is not selected for erasure. (The device “erase suspends” all sectors selected for erasure.) Note that
when the device is in the Erase Suspend mode, the Reset command is not required for read operations and is ignored.
Further nesting of erase operation is not permitted. Reading at any address within erase suspended sectors produces status
information on DQ7-DQ0. The system can use DQ6 and DQ2 together, to determine if a sector is actively erasing or is erase-
suspended. Refer to Table 12 on page 33 for information on these status bits.
A read operation from the erase-suspended bank returns polling data during the first 8 µs after the erase suspend command is
issued; read operations thereafter return array data. Read operations from the other bank return array data with no latency.
After an erase-suspended program operation is complete, the bank returns to the erase-suspend read mode. The system can
determine the status of the program operation using the DQ7, DQ6, and/or RY/BY# status bits, just as in the standard program
operation.
To resume the sector erase operation, the system must write the Erase Resume command. The bank address of the erase-
suspended bank is required when writing this command. Further writes of the Resume command are ignored. Another Erase
Suspend command can be written after the chip has resumed erasing.
The following are the allowable operations when Erase Suspend is issued under certain conditions:
For the Busy Sectors, the host system may
Read status
Write the Erase Resume command
For the Non Busy Sectors, the system may
Read data
Program data or write the Suspend/Resume Erase command
7.7.5 Program Suspend/Program Resume Commands
The Program Suspend command allows the system to interrupt an embedded programming operation so that data can read from
any non-suspended sector. When the Program Suspend command is written during a programming process, the device halts the
programming operation and updates the status bits.
After the programming operation has been suspended, the system can read array data from any non-suspended sector. If a read is
needed from the Secured Silicon Sector area, then user must use the proper command sequences to enter and exit this region. The
Sector Erase and Program Resume Command is ignored if the Secured Silicon sector is enabled.
After the Program Resume command is written, the device reverts to programming. The system can determine the status of the
program operation using the DQ7, DQ6, and/or RY/BY# status bits, just as in the standard program operation. See Write Operation
Status on page 32 for more information.
The system must write the Program Resume command in order to exit the Program Suspend mode, and continue the programming
operation. Further writes of the Program Resume command are ignored. Another Program Suspend command can be written after
the device has resumed programming.
The following are the allowable operations when Program Suspend is issued under certain conditions:
For the Busy Sectors, the host system may write the Program Resume command
For the Non Busy Sectors, the system may read data
Document Number: 002-00948 Rev. *C
Page 30 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
7.7.6 Accelerated Program Operations
Accelerated programming is enabled through the ACC function. This method is faster than the standard program command
sequences.
The device offers accelerated program operations through the ACC pin. When the system asserts VHH (12V) on the ACC pin, the
device automatically enters the Unlock Bypass mode. The system may then write the two-cycle Unlock Bypass program command
sequence to do accelerated programming. The device uses the higher voltage on the ACC pin to accelerate the operation. Any
sector that is being protected with the WP# pin is still protected during accelerated program. Removing VHH from the ACC input,
upon completion of the embedded program operation, returns the device to normal operation.
Notes
In this mode, the write protection function is bypassed unless the PPB Lock Bit = 1.
The ACC pin must not be at VHH for operations other than accelerated programming or device damage may result.
The ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result.
The Accelerated Program command is not permitted if the Secured Silicon sector is enabled.
7.7.7 Unlock Bypass
The device features an Unlock Bypass mode to facilitate faster programming, erasing (Chip Erase), as well as CFI commands. Once
the device enters the Unlock Bypass mode, only two write cycles are required to program or erase data, instead of the normal four
cycles for program or 6 cycles for erase. This results in faster total programming/erasing time.
Command Definitions on page 67 shows the requirements for the unlock bypass command sequences.
During the unlock bypass mode only the Read, Unlock Bypass Program and Unlock Bypass Reset commands are valid. To exit the
unlock bypass mode, the system must issue the two-cycle unlock bypass reset command sequence, which returns the device to
read mode.
Notes
1. The Unlock Bypass Command is ignored if the Secured Silicon sector is enabled.
2. Unlike the standard program or erase commands, there is no Unlock Bypass Program/Erase Suspend or Program/Erase
Resume command.
7.7.8 Simultaneous Read/Write
The simultaneous read/write feature allows the host system to read data from one bank of memory while programming or erasing in
another bank of memory.
The Simultaneous Read/Write feature can be used to perform the following:
Programming in one bank, while reading in the other bank
Erasing in one bank, while reading in the other bank
Programming a PPB, while reading data from the large bank or status from the small bank
Erasing a PPB, while reading data from the large bank or status from the small bank
Any of the above situations while in the Secured Silicon Sector Mode
The Simultaneous R/W feature can not be performed during the following modes:
CFI Mode
Password Program operation
Password Verify operation
As an alternative to using the Simultaneous Read/Write feature, the user may also suspend an erase or program operation to read
in another location within the same bank (except for the sector being erased).
Restrictions
The Simultaneous Read/Write function is tested by executing an embedded operation in the small (busy) bank while performing
other operations in the big (non-busy) bank. However, the opposite case is neither tested nor valid. That is, it is not tested by
executing an embedded operation in the big (busy) bank while performing other operations in the small (non-busy) bank.
Document Number: 002-00948 Rev. *C
Page 31 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
7.8
Write Operation Status
The device provides several bits to determine the status of a program or erase operation. The following subsections describe the
function of DQ7, DQ6, DQ2, DQ5, DQ3, and RY/BY#.
7.8.1 DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase algorithm is in progress or
completed, or whether a bank is in Erase Suspend. Data# Polling is valid after the rising edge of the final WE# pulse in the command
sequence. Note that Data# Polling returns invalid data for the address being programmed or erased.
During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7
status also applies to programming during Erase Suspend. When the Embedded Program algorithm is complete, the device outputs
the datum programmed to DQ7. The system must provide the program address to read valid status information on DQ7.
If a program address falls within a protected sector, Data# polling on DQ7 is active for approximately 1 µs, then that bank returns to
the read mode without programming the sector. If an erase address falls within a protected sector, Toggle BIT (DQ6) is active for
150 s, then the device returns to the read mode without erasing the sector. Please note that Data# polling (DQ7) may give
misleading status when an attempt is made to program or erase a protected sector.
During the Embedded Erase Algorithm, Data# polling produces a “0” on DQ7. When the Embedded Erase algorithm is complete
Data# Polling produces a “1” on DQ7. The system must provide an address within any of the sectors selected for erasure to read
valid status information on DQ7.
In asynchronous mode, just prior to the completion of an Embedded Program or Erase operation, DQ7 may change asynchronously
with DQ6-DQ0 while Output Enable (OE#) is asserted low. That is, the device may change from providing status information to valid
data on DQ7. Depending on when the system samples the DQ7 output, it may read the status or valid data. Even if the device has
completed the program or erase operation and DQ7 has valid data, the data outputs on DQ6-DQ0 may be still invalid. Valid data on
DQ7-D00 appears on successive read cycles.
See the following for more information: Table 13. Write Operation Status on page 36 shows the outputs for Data# Polling on DQ7.
Figure 7 Data# Polling Algorithm on page 32 shows the Data# Polling timing diagram.
Figure 7. Data# Polling Algorithm
START
Read DQ7–DQ0
Addr = VA
Yes
DQ7 = Data?
No
No
DQ5 = 1?
Yes
Read DQ7–DQ0
Addr = VA
Yes
DQ7 = Data?
No
PASS
FAIL
Notes
41. VA = Valid address for programming. During a sector erase operation, a valid address is an address within any sector selected for erasure. During chip erase, a valid
address is any non-protected sector address.
42.DQ7 should be rechecked even if DQ5 = 1 because DQ7 may change simultaneously with DQ5.
Document Number: 002-00948 Rev. *C
Page 32 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
7.8.2 DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete, or whether the device
has entered the Erase Suspend mode.
Toggle Bit I may be read at any address in the same bank, and is valid after the rising edge of the final WE# pulse in the command
sequence (prior to the program or erase operation), and during the sector erase time-out.
During an Embedded Program or Erase algorithm operation, two immediate consecutive read cycles to any address cause DQ6 to
toggle. When the operation is complete, DQ6 stops toggling. For asynchronous mode, either OE# or CE# can be used to control the
read cycles. For synchronous mode, the rising edge of ADV# is used or the rising edge of clock while ADV# is Low.
After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6 toggles for approximately 100 µs,
then returns to reading array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected
sectors, and ignores the selected sectors that are protected.
The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erase-suspended. When the
device is actively erasing (that is, the Embedded Erase algorithm is in progress), DQ6 toggles. When the device enters the Erase
Suspend mode, DQ6 stops toggling. However, the system must also use DQ2 to determine which sectors are erasing or erase-
suspended. Alternatively, the system can use DQ7 (see the subsection on DQ7: Data# Polling).
If a program address falls within a protected sector, DQ6 toggles for approximately 1 µs after the program command sequence is
written, then returns to reading array data.
DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program Algorithm is complete.
See Figure 29 Toggle Bit Timings (During Embedded Algorithms) on page 60 for additional information.
7.8.3 DQ2: Toggle Bit II
The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that is, the Embedded
Erase algorithm is in progress), or whether that sector is erase-suspended. Toggle Bit II is valid after the rising edge of the final WE#
pulse in the command sequence. DQ2 toggles when the system performs two consecutive reads at addresses within those sectors
that have been selected for erasure. But DQ2 cannot distinguish whether the sector is actively erasing or is erase-suspended. DQ6,
by comparison, indicates whether the device is actively erasing, or is in Erase Suspend, but cannot distinguish which sectors are
selected for erasure. Thus, both status bits are required for sector and mode information. Refer to Table 12 to compare outputs for
DQ2 and DQ6. See DQ6: Toggle Bit I on page 33 for additional information.
7.8.4 Reading Toggle Bits DQ6/DQ2
Whenever the system initially begins reading toggle bit status, it must perform two consecutive reads of DQ7-DQ0 in a row in order
to determine whether a toggle bit is toggling. Typically, the system notes and stores the value of the toggle bit after the first read.
After the second read, the system compares the new value of the toggle bit with the first. If the toggle bit is not toggling, the device
completes the program or erases operation. The system can read array data on DQ7-DQ0 on the following read cycle.
However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system also notes whether
the value of DQ5 is high (see the section on DQ5). If it is, the system then determines again whether the toggle bit is toggling, since
the toggle bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device has successfully
completed the program or erases operation. If it is still toggling, the device had not completed the operation successfully, and the
system writes the reset command to return to reading array data.
The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has not gone high. The system
may continue to monitor the toggle bit and DQ5 through successive read cycles, determining the status as described in the previous
paragraph. Alternatively, the system may choose to perform other system tasks. In this case, the system must start at the beginning
of the algorithm when it returns to determine the status of the operation. Refer to Figure 8 for more on the Toggle Bit Algorithm.
Table 12. DQ6 and DQ2 Indications
If device is
and the system reads
then DQ6
and DQ2
programming,
at any address,
toggles,
does not toggle.
at an address within a sector selected for
erasure,
toggles,
toggles,
also toggles.
actively erasing,
at an address within sectors not selected
for erasure,
does not toggle.
Document Number: 002-00948 Rev. *C
Page 33 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Table 12. DQ6 and DQ2 Indications
If device is
and the system reads
then DQ6
and DQ2
at an address within sectors selected for
erasure,
does not
toggle,
toggles.
erase suspended,
at an address within sectors not selected
for erasure,
returns array
data,
returns array data. The system can read
from any sector not selected for erasure.
programming in erase
suspend,
at any address,
toggles,
is not applicable.
Figure 8. Toggle Bit Algorithm
START
Read Byte
(DQ0-DQ7)
Address = VA
Read Byte
(DQ0-DQ7)
(Note 43)
Address = VA
No
DQ6 = Toggle?
Yes
No
DQ5 = 1?
Yes
Read Byte Twice
(DQ0-DQ7)
Adrdess = VA
(Notes 43,
No
DQ6 = Toggle?
Yes
FAIL
PASS
Notes
43. Read toggle bit with two immediately consecutive reads to determine whether or not it is toggling.
44.Recheck toggle bit because it may stop toggling as DQ5 changes to 1.
Document Number: 002-00948 Rev. *C
Page 34 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
7.8.5 DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has exceeded a specified internal pulse count limit. Under these conditions DQ5
produces a 1. This is a failure condition that indicates the program or erase cycle was not successfully completed.
The DQ5 failure condition may appear if the system tries to program a 1 to a location that is previously programmed to 0. Only an
erase operation can change a 0 back to a 1. Under this condition, the device halts the operation, and when the operation has
exceeded the timing limits, DQ5 produces a 1.
Under both these conditions, the system issues the reset command to return the device to reading array data.
7.8.6 DQ3: Sector Erase Timer
After writing a sector erase command sequence, the system may read DQ3 to determine whether or not erasure has begun. (The
sector erase timer does not apply to the chip erase command.) If additional sectors are selected for erasure, the entire time-out also
applies after each additional sector erase command. When the time-out period is complete, DQ3 switches from a “0” to a “1.” If the
time between additional sector erase commands from the system can be assumed to be less than 50 µs, the system need not
monitor DQ3. See Sector Erase on page 28 for more details.
After the sector erase command is written, the system reads the status of DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that
the device has accepted the command sequence, then reads DQ3. If DQ3 is “1,” the Embedded Erase algorithm has begun; all
further commands (except Erase Suspend) are ignored until the erase operation is complete. If DQ3 is “0,” the device accepts
additional sector erase commands.
To ensure the command has been accepted, the system software check the status of DQ3 prior to and following each sub-sequent
sector erase command. If DQ3 is high on the second status check, the last command might not have been accepted. Table 13
shows the status of DQ3 relative to the other status bits.
7.8.7 RY/BY#: Ready/Busy#
The device provides a RY/BY# open drain output pin as a way to indicate to the host system that the Embedded Algorithms are
either in progress or have been completed. If the output of RY/BY# is low, the device is busy with either a program, erase, or reset
operation. If the output is floating, the device is ready to accept any read/write or erase operation. When the RY/BY# pin is low, the
device will not accept any additional program or erase commands with the exception of the Erase suspend command. If the device
has entered Erase Suspend mode, the RY/BY# output is floating. For programming, the RY/BY# is valid (RY/BY# = 0) after the
rising edge of the fourth WE# pulse in the four write pulse sequence. For chip erase, the RY/BY# is valid after the rising edge of the
sixth WE# pulse in the six write pulse sequence. For sector erase, the RY/BY# is also valid after the rising edge of the sixth WE#
pulse.
If RESET# is asserted during a program or erase operation, the RY/BY# pin remains a 0 (busy) until the internal reset operation is
complete, which requires a time of tREADY (during Embedded Algorithms). The system can thus monitor RY/BY# to determine
whether the reset operation is complete. If RESET# is asserted when a program or erase operation is not executing (RY/BY# pin is
floating), the reset operation is completed in a time of tREADY (not during Embedded Algorithms). The system can read data tRH after
the RESET# pin returns to VIH.
Since the RY/BY# pin is an open-drain output, several RY/BY# pins can be tied together in parallel with a pull-up resistor to VCC. An
external pull-up resistor is required to take RY/BY# to a VIH level since the output is an open drain.
Table 13 shows the outputs for RY/BY#, DQ7, DQ6, DQ5, DQ3 and DQ2. Figure 19, Figure 23, Figure 25, and Figure 26 show RY/
BY# for read, reset, program, and erase operations, respectively.
Document Number: 002-00948 Rev. *C
Page 35 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Table 13. Write Operation Status
Operation
DQ7
(Note 46)
DQ5
(Note 45)
DQ2
DQ6
DQ3
RY/BY#
(Note 46)
No toggle
Toggle
Embedded Program Algorithm
DQ7#
0
Toggle
Toggle
0
0
N/A
1
0
0
Standard
Mode
Embedded Erase Algorithm
Reading within Erase
Suspended Sector
1
No toggle
0
N/A
Toggle
1
Erase
Suspend
Mode
Reading within Non-Erase
Suspended Sector
Data
Data
Data
0
Data
N/A
Data
N/A
1
0
Erase-Suspend-Program
DQ7#
Toggle
Notes
45. DQ5 switches to 1 when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits. See DQ5: Exceeded Timing Limits
on page 35 for more information.
46. DQ7 and DQ2 require a valid address when reading status information. See DQ7: Data# Polling on page 32 and DQ2: Toggle Bit II on page 33 for further details.
7.9
Reset Command
Writing the reset command resets the device to the read or erase-suspend-read mode. Address bits are don’t cares for this
command.
The reset command may be written between the cycles in an erase command sequence before erasing begins. This resets the
device to the read mode. However, once erasure begins, the device ignores the reset commands until the operation is complete.
The reset command may be written between the cycles in a program command sequence before programming begins. This resets
the device to the read mode. If the program command sequence is written while the device is in the Erase Suspend mode, writing
the reset command returns the device to the erase-suspend-read mode. However, once programming begins, the device ignores the
reset commands until the operation is complete.
The reset command may be written between the cycles in an autoselect command sequence. Once in the autoselect mode, the
reset command must be written to exit the autoselect mode and return to the read mode.
If DQ5 goes high during a program or erase operation, writing the reset command returns the device to the read mode or erase-
suspend-read-mode if the device was in Erase Suspend. When the reset command is written, before the embedded operation starts,
the device requires tRR before it returns to the read or erase-suspend-read mode.
Table 14. Reset Command Timing
Parameter
Description
Max.
Unit
tRR
Reset Command to Read Mode or Erase-Suspend-Read Mode
250
ns
Document Number: 002-00948 Rev. *C
Page 36 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
8. Advanced Sector Protection/Unprotection
The Advanced Sector Protection/Unprotection feature disables or enables programming or erase operations in any or all sectors and
can be implemented through software and/or hardware methods, which are independent of each other. This section describes the
various methods of protecting data stored in the memory array. An overview of these methods in shown in Figure 9.
Figure 9. Advanced Sector Protection/Unprotection
Hardware Methods
Software Methods
WP# = VIL
(Two outermost sectors
locked in large bank)
Persistent Method
Password Method
64-bit Password
(One Time Protect)
1. Bit is volatile, and defaults to “0” on reset.
PPB Lock Bit1,2,3
2. Programming to “1” locks all PPBs to their
current state.
0 = PPBs Unlocked
1 = PPBs Locked
3. Once programmed to “1”, requires hardware
reset to unlock.
Persistent
Protection Bit
(PPB)5,6
Dynamic
Protection Bit
(DYB)7,8,9
Memory Array
Sector Group 0
Sector Group 1
Sector Group 2
PPB 0
PPB 1
PPB 2
DYB 0
DYB 1
DYB 2
Sector Group N-2
Sector Group N-1
Sector Group N4
PPB N-2
PPB N-1
PPB N
DYB N-2
DYB N-1
DYB N
4. N = 23 for S29CD016J/CL016J,
31 for S29CD032J/CL032J.
5. PPBs programmed individually,
but cleared collectively.
7. Protect effective only if PPB Lock Bit is
unlocked and corresponding PPB is “0”
(unprotected).
6. 0 = Sector Group Unprotected;
1 = Sector Group Protected
8. Volatile Bits.
9. 0 = Sector Group Unprotected;
1 = Sector Group Protected
Document Number: 002-00948 Rev. *C
Page 37 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
8.1
Advanced Sector Protection Overview
As shipped from the factory, all devices default to the persistent mode when power is applied, and all sector groups are unprotected.
The device programmer or host system must then choose which sector group protection method to use. Programming (setting to “0”)
any one of the following two one-time programmable, non-volatile bits locks the device permanently in that mode:
Persistent Protection Mode Lock Bit
Password Protection Mode Lock Bit
After selecting a sector group protection method, each sector group can operate in any of the following three states:
1. Persistently Locked. A sector group is protected and cannot be changed.
2. Dynamically locked. The selected sector groups are protected and can be altered via software commands.
3. Unlocked. The sector groups are unprotected and can be erased and/or programmed.
These states are controlled by the bit types described in sections Persistent Protection Bits on page 39 to Hardware Data Protection
Methods on page 43.
Notes
1. If the password mode is chosen, the password must be programmed before setting the corresponding lock register bit.
The user must be sure that the password is correct when the Password Mode Locking Bit is set, as there is no means to
verify the password afterwards.
2. If both lock bits are selected to be programmed (to zeros) at the same time, the operation aborts.
3. Once the Password Mode Lock Bit is programmed, the Persistent Mode Lock Bit is permanently disabled, and no
changes to the protection scheme are allowed. Similarly, if the Persistent Mode Lock Bit is programmed, the Password
Mode is permanently disabled.
4. It is important that the mode is explicitly selected when the device is first programmed, rather than relying on the default
mode alone. This is so that it is impossible for a system program or virus to later set the Password Mode Locking Bit,
which would cause an unexpected shift from the default Persistent Sector Protection Mode into the Password Protection
Mode.
5. If the user attempts to program or erase a protected sector, the device ignores the command and returns to read mode. A
program command to a protected sector enables status polling for approximately 1 µs before the device returns to read
mode without modifying the contents of the protected sector. An erase command to a protected sector enables status
polling for approximately 50 µs, after which the device returns to read mode without having erased the protected sector.
6. For the command sequence required for programming the lock register bits, refer to Command Definitions on page 67.
Document Number: 002-00948 Rev. *C
Page 38 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
8.2
Persistent Protection Bits
The Persistent Protection Bits are unique and nonvolatile. A single Persistent Protection Bit is assigned to a maximum for four
sectors (see the sector address tables for specific sector protection groupings). All eight-Kbyte boot-block sectors have individual
sector Persistent Protection Bits (PPBs) for greater flexibility.
Notes
1. Each PPB is individually programmed and all are erased in parallel. There are no means for individually erasing a specific
PPB and no specific sector address is required for this operation.
2. If a PPB requires erasure, all of the sector PPBs must first be programmed prior to PPB erasing. It is the responsibility of
the user to perform the preprogramming operation. Otherwise, an already erased sector PPB has the potential of being
over-erased. There is no hardware mechanism to prevent sector PPB over-erasure.
3. If the PPB Lock Bit is set, the PPB Program or erase command does not execute and times-out without programming or
erasing the PPB.
8.2.1 Programming PPB
The PPB Program Command is used to program, or set, a given PPB. The first three cycles in the PPB Program Command are
standard unlock cycles. The fourth cycle in the PPB Program Command executes the pulse which programs the specified PPB. The
user must wait either 100 µs or until DQ6 stops toggling before executing the fifth cycle, which is the read verify portion of the PPB
Program Command. The sixth cycle outputs the status of the PPB Program operation.
In the event that the program PPB operation was not successful, the user can loop directly to the fourth cycle of the PPB Program
Command to perform the program pulse and read verification again. After four unsuccessful loops through the program pulse and
read verification cycles the PPB programming operation should be considered a failure.
Figure 10. PPB Program Operation
Write 0xAA to 0x555
Write 0x55 to 0x2AA
Write 0x60 to 0x555
Write 0x68 to SG+WP
Note: Reads from the
Either poll DQ6 in the
small bank and wait for
it to stop toggling OR
wait 100 μs
small bank at this point
return the status of the
operation, not read array
data.
Write 0x48 to SG+WP
Read from SG+WP
NO
NO
5th attempt?
YES
DQ0 = 1?
YES
Error
Done
Document Number: 002-00948 Rev. *C
Page 39 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
8.2.2 Erasing PPB
The All PPB Erase command is used to erase all the PPBs in bulk. There are no means for individually erasing a specific PPB. The
first three cycles of the PPB Erase command are standard unlock cycles. The fourth cycle executes the erase pulse to all the PPBs.
The user must wait either 20 ms or until DQ6 stops toggling before executing the fifth cycle, which is the read verify portion of the
PPB Erase Command. The sixth cycle outputs the status of the PPB Erase operation.
In the event that the erase PPB operation was not successful, the user can loop directly to the fourth cycle of the All PPB Erase
Command to perform the erase pulse and read verification again. After four unsuccessful loops through the erase pulse and read
verification cycles, the PPB erasing operation should be considered a failure.
Note
All PPB must be preprogrammed prior to issuing the All PPB Erase Command.
Figure 11. PPB Erase Operation
Write 0xAA to 0x555
Write 0x55 to 0x2AA
Write 0x60 to 0x555
Write 0x60 to WP
Note: Reads from the
Either poll DQ6 in the
small bank and wait for
it to stop toggling OR
wait 20 ms
small bank at this point
return the status of the
operation, not read array
data.
Write 0x40 to WP
Read from WP
NO
NO
5th attempt?
YES
DQ0 = 0?
YES
Error
Done
Document Number: 002-00948 Rev. *C
Page 40 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
8.3
Persistent Protection Bit Lock Bit
The Persistent Protection Bit Lock Bit is a global volatile bit for all sectors. When set to “1”, it locks all PPBs; when set to “0”, it allows
the PPBs to be changed. There is only one PPB Lock Bit per device.
Notes
1. No software command sequence unlocks this bit unless the device is in the password protection mode; only a hardware
reset or a power-up clears this bit.
2. The PPB Lock Bit must be set only after all PPBs are configured to the desired settings.
8.4
Dynamic Protection Bits
A Dynamic Protection Bit (DYB) is volatile and unique for each sector group and can be individually modified. DYBs only control the
protection scheme for unprotected sector groups that have their PPBs set to “0”. By issuing the DYB Set or Clear command
sequences, the DYBS are set or cleared, thus placing each sector group in the protected or unprotected state respectively. This
feature allows software to easily protect sector groups against inadvertent changes, yet does not prevent the easy removal of
protection when changes are needed.
Notes
1. The DYBs can be set or cleared as often as needed with the DYB Write Command.
2. When the parts are first shipped, the PPBs are cleared, the DYBs are cleared, and PPB Lock is defaulted to power up in
the cleared state – meaning the PPBs are changeable. The DYB are also always cleared after a power-up or reset.
3. It is possible to have sector groups that are persistently locked with sector groups that are left in the dynamic state.
4. The DYB Set or Clear commands for the dynamic sector groups signify the protected or unprotected state of the sector
groups respectively. However, if there is a need to change the status of the persistently locked sector groups, a few more
steps are required. First, the PPB Lock Bit must be cleared by either putting the device through a power-cycle, or
hardware reset. The PPBs can then be changed to reflect the desired settings. Setting the PPB Lock Bit once again locks
the PPBs, and the device operates normally again.
Table 15. Sector Protection Schemes
DYB
0
PPB
0
PPB Lock
Sector State
Unprotected—PPB and DYB are changeable
0
1
0
0
0
1
1
1
Unprotected—PPB not changeable, DYB is changeable
0
0
0
1
Protected—PPB and DYB are changeable
1
0
1
1
0
1
Protected—PPB not changeable, DYB is changeable
1
0
1
1
Document Number: 002-00948 Rev. *C
Page 41 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
8.5
Password Protection Method
The Password Protection Method allows an even higher level of security than the Persistent Sector Protection Mode by requiring a
64-bit password for unlocking the device PPB Lock Bit. In addition to this password requirement, after power-up and reset, the PPB
Lock Bit is set “1” in order to maintain the password mode of operation. Successful execution of the Password Unlock command by
entering the entire password clears the PPB Lock Bit, allowing for sector PPBs modifications.
Notes
1. There is no special addressing order required for programming the password. Once the password is written and verified,
the Password Mode Locking Bit must be set in order to prevent access.
2. The Password Program Command is only capable of programming “0”s. Programming a “1” after a cell is programmed as
a “0” results in a time-out with the cell as a “0”. (This is an OTP area).
3. The password is all “1”s when shipped from the factory.
4. When the password is undergoing programming, Simultaneous Read/Write operation is disabled. Read operations to any
memory location returns the programming status. Once programming is complete, the user must issue a Read/Reset
command to return the device to normal operation.
5. All 64-bit password combinations are valid as a password.
6. There is no means to read, program or erase the password is after it is set.
7. The Password Mode Lock Bit, once set, prevents reading the 64-bit password on the data bus and further password
programming.
8. The Password Mode Lock Bit is not erasable.
9. The exact password must be entered in order for the unlocking function to occur.
10.There is a built-in 2-µs delay for each password check. This delay is intended to stop any efforts to run a program that
tries all possible combinations in order to crack the password.
Document Number: 002-00948 Rev. *C
Page 42 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
8.6
Hardware Data Protection Methods
The device offers several methods of data protection by which intended or accidental erasure of any sectors can be prevented via
hardware means. The following subsections describe these methods.
8.6.1 WP# Method
The Write Protect feature provides a hardware method of protecting the two outermost sectors of the large bank.
If the system asserts VIL on the WP# pin, the device disables program and erase functions in the two “outermost” boot sectors (8-
Kbyte sectors) in the large bank. If the system asserts VIH on the WP# pin, the device reverts to whether the boot sectors were last
set to be protected or unprotected. That is, sector protection or unprotection for these sectors depends on whether they were last
protected or unprotected.
Note that the WP# pin must not be left floating or unconnected as inconsistent behavior of the device may result.
The WP# pin must be held stable during a command sequence execution
8.6.2 Low V Write Inhibit
CC
When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC power-up and power-down.
The command register and all internal program/erase circuits are disabled, and the device resets to reading array data. Subsequent
writes are ignored until VCC is greater than VLKO. The system must provide the proper signals to the control inputs to prevent
unintentional writes when VCC is greater than VLKO
.
8.6.3 Write Pulse “Glitch Protection”
Noise pulses of less than 5 ns (typical) on OE#, CE# or WE# do not initiate a write cycle.
8.6.4 Power-Up Write Inhibit
If WE# = CE# = RESET# = VIL and OE# = VIH during power-up, the device does not accept commands on the rising edge of WE#.
The internal state machine is automatically reset to the read mode on power-up.
8.6.5 V and V Power-up And Power-down Sequencing
CC
IO
The device imposes no restrictions on VCC and VIO power-up or power-down sequencing. Asserting RESET# to VIL is required
during the entire VCC and VIO power sequence until the respective supplies reach the operating voltages. Once VCC and VIO attain
the operating voltages, deassertion of RESET# to VIH is permitted. Refer to timing in VCC and VIO Power-up on page 52.
8.6.6 Logical Inhibit
Write cycles are inhibited by holding any one of OE# = VIL, CE# = VIH, or WE# = VIH. To initiate a write cycle, CE# and WE# must be
a logical zero (VIL) while OE# is a logical one (VIH).
Document Number: 002-00948 Rev. *C
Page 43 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
9. Secured Silicon Sector Flash Memory Region
The Secured Silicon Sector provides an extra Flash memory region that enables permanent part identification through an Electronic
Serial Number (ESN). The Secured Silicon Sector is a 256-byte flash memory area that is either programmable at the customer, or
by Cypress at the request of the customer. See Table 16 for the Secured Silicon Sector address ranges.
All Secured Silicon reads outside of the 256-byte address range return invalid data.
Table 16. Secured Silicon Sector Addresses
Ordering Option
Sector Size (Bytes)
Address Range
Top Boot
256
00000h-0003Fh (16 Mb and 32 Mb)
FFFC0h–FFFFFh (32 Mb)
7FFC0h–7FFFFh (16 Mb)
Bottom Boot
256
The device allows Simultaneous Read/Write operation while the Secured Silicon Sector is enabled. However, several restrictions
are associated with Simultaneous Read/Write operation and device operation when the Secured Silicon Sector is enabled:
1. The Secured Silicon Sector is not available for reading while the Password Unlock, any PPB program/erase operation, or
Password programming are in progress. Reading to any location in the small bank will return the status of these
operations until these operations have completed execution.
2. Programming the DYB associated with the overlaid boot-block sector results in the DYB NOT being updated. This occurs
only when the Secured Silicon sector is not enabled.
3. Reading the DYB associated with the overlaid boot-block sector when the PPB Lock/DYB Verify command is issued,
causes the read command to return invalid data. This function occurs only when the Secured Silicon Sector is not
enabled.
4. All commands are available for execution when the Secured Silicon Sector is enabled, except the following:
a. Any Unlock Bypass command
b. CFI
c. Accelerated Program
d. Program and Sector Erase Suspend
e. Program and Sector Erase Resume
Issuing the above commands while the Secured Silicon Sector is enabled results in the command being ignored.
5. It is valid to execute the Sector Erase command on any sector other than the Secured Silicon Sector when the Secured
Silicon Sector is enabled. However, it is not possible to erase the Secured Silicon Sector using the Sector Erase
Command, as it is a one-time programmable (OTP) area that can not be erased.
6. Executing the Chip Erase command is permitted when the Secured Silicon Sector is enabled. The Chip Erase command
erases all sectors in the memory array, except for sector 0 in top-boot block configuration, or sector 45 in bottom-boot
block configuration. The Secured Silicon Sector is a one-time programmable memory area that cannot be erased.
7. Executing the Secured Silicon Sector Entry command during program or erase suspend mode is allowed. The Sector
Erase/Program Resume command is disabled when the Secured Silicon sector is enabled; the user cannot resume
programming of the memory array until the Exit Secured Silicon Sector command is written.
8. Address range 00040h–007FFh for the top bootblock, and FF00h–FFF7Fh return invalid data when addressed with the
Secured Silicon sector enabled.
9. The Secured Silicon Sector Entry command is allowed when the device is in either program or erase suspend modes. If
the Secured Silicon sector is enabled, the program or erase suspend command is ignored. This prevents resuming either
programming or erasure on the Secured Silicon sector if the overlayed sector was undergoing programming or erasure.
The host system must ensure that the device resume any suspended program or erase operation after exiting the
Secured Silicon sector.
Document Number: 002-00948 Rev. *C
Page 44 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
9.1
Secured Silicon Sector Protection Bit
The Secured Silicon Sector can be shipped unprotected, allowing customers to utilize that sector in any manner they choose.
Please note the following:
The Secured Silicon Sector can be read any number of times, but can be programmed and locked only once. The Secured Silicon
Sector Protection Bit must be used with caution as once locked, there is no procedure available for unlocking the Secured Silicon
Sector area and none of the bits in the Secured Silicon Sector memory space can be modified in any way.
Once the Secured Silicon Sector is locked and verified, the system must write the Exit Secured Silicon Sector Region command
sequence to return the device to the memory array.
9.2
Secured Silicon Sector Entry and Exit Commands
The system can access the Secured Silicon Sector region by issuing the three-cycle Enter Secured Silicon Sector command
sequence. The device continues to access the Secured Silicon Sector region until the system issues the four-cycle Exit Secured
Silicon Sector command sequence. See the Table 34. Memory Array Command Definitions (x32 Mode) on page 67 and Table 35.
Sector Protection Command Definitions (x32 Mode) on page 68 for address and data requirements for both command sequences.
The Secured Silicon Sector Entry Command allows the following commands to be executed
Read Secured Silicon areas
Program Secured Silicon Sector (only once)
After the system has written the Enter Secured Silicon Sector command sequence, it can read the Secured Silicon Sector by using
the addresses listed in Table 16 on page 44. This mode of operation continues until the system issues the Exit Secured Silicon
Sector command sequence, or until power is removed from the device.
Document Number: 002-00948 Rev. *C
Page 45 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
10. Electronic Marking
Electronic marking has been programmed into the device, prior to shipment from Cypress, to ensure traceability of individual
products. The electronic marking is stored and locked within a one-time programmable region. Detailed information on Electronic
Marking will be provided in a data sheet supplement.
11. Power Conservation Modes
11.1 Standby Mode
When the system is not reading or writing to the device, it can place the device in standby mode. In this mode, current consumption
is greatly reduced, and outputs are placed in a high impedance state, independent of OE# input. The device enters CMOS standby
mode when the CE# and RESET# inputs are both held at VCC ± 10%. The device requires standard access time (tCE) for read
access before it is ready to read data. If the device is deselected during erasure or programming, the device draws active current
until the operation is completed. ICC5 in Table 19 on page 49 represents the standby current specification.
Caution
Entering standby mode via the RESET# pin also resets the device to read mode and floats the data I/O pins. Furthermore, entering
ICC7 during a program or erase operation leaves erroneous data in the address locations being operated on at the time of the
RESET# pulse. These locations require updating after the device resumes standard operations. See Hardware RESET# Input
Operation on page 46 for further discussion of the RESET# pin and its functions.
11.2 Automatic Sleep Mode
The automatic sleep mode minimizes Flash device energy consumption. The automatic sleep mode is independent of the CE#, WE#
and OE# control signals. While in sleep mode, output data is latched and always available to the system.
While in asynchronous mode, the device automatically enables this mode when addresses remain stable for tACC + 60 ns. Standard
address access timings provide new data when addresses are changed. While in synchronous mode, the device automatically
enables this mode when either the first active CLK level is greater than tACC or the CLK runs slower than 5 MHz. A new burst
operation is required to provide new data. ICC8 in DC Characteristic, CMOS Compatible on page 49 represents the automatic sleep
mode current specification.
11.3 Hardware RESET# Input Operation
The RESET# input provides a hardware method of resetting the device to reading array data. When RESET# is driven low, the
device immediately terminates any operation in progress, tristates all outputs, resets the configuration register, and ignores all read/
write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. Any
operation that was interrupted should be reinitiated once the device is ready to accept another command sequence, in order to
ensure data integrity.
When RESET# is held at VSS ±0.2 V, the device draws CMOS standby current (ICC4). If RESET# is held at VIL but not within VSS
±0.2 V, the standby current is greater.
RESET# may be tied to the system reset circuitry, thus a system reset would also reset the Flash memory, enabling the system to
read the boot-up firmware from the Flash memory.
If RESET# is asserted during a program or erase operation, the RY/BY# pin remains low until the reset operation is internally
complete. This action requires between 1 µs and 7 µs for either Chip Erase or Sector Erase. The RY/BY# pin can be used to
determine whether the reset operation is complete. Otherwise, allow for the maximum reset time of 11 µs.
If RESET# is asserted when a program or erase operation is not executing (RY/BY# = 1), the reset operation completes within 500
ns. The Simultaneous Read/Write feature of this device allows the user to read a bank after 500 ns if the bank is in the read/reset
mode at the time RESET# is asserted. If one of the banks is in the middle of either a program or erase operation when RESET# is
asserted, the user must wait 11 µs before accessing that bank.
Asserting RESET# active during VCC and VIO power up is required to guarantee proper device initialization until VCC and VIO have
reached steady state voltages.
11.4 Output Disable (OE#)
When the OE# input is at VIH, output from the device is disabled. The outputs are placed in the high impedance state.
Document Number: 002-00948 Rev. *C
Page 46 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
12. Electrical Specifications
12.1 Absolute Maximum Ratings
Table 17. Absolute Maximum Ratings
Parameter
Storage Temperature, Plastic Packages
Ambient Temperature with Power Applied
VCC, VIO (Note 47) for 2.6 V devices (S29CD-J)
VCC, VIO (Note 47) for 3.3 V devices (S29CL-J)
ACC, A9, and RESET# (Note 48)
Rating
–65 °C to +150 °C
–65 °C to +145 °C
–0.5V to +3.6V
–0.5V to +3.6V
–0.5V to +13.0V
–0.5V to +3.6V (CL016J)
–0.5V to +2.75V (CD016J)
–0.5V to +3.6V (CL032J)
–0.5V to +2.75V (CD032J)
200 mA
(with the exception of CLK)
All other pins (Note 47)
Address, Data, Control Signals (Note 47)
Output Short Circuit Current (Note 49)
Notes
47. Minimum DC voltage on input or I/O pins is –0.5 V. During voltage transitions, input at I/O pins may overshoot V to –2.0V for periods of up to 20 ns. See Figure 13.
SS
Maximum DC voltage on output and I/O pins is 3.6V. During voltage transitions output pins may overshoot to V + 2.0V for periods up to 20 ns. See Figure 13.
CC
48. Minimum DC input voltage on pins ACC, A9, and RESET# is -0.5V. During voltage transitions, A9 and RESET# may overshoot V to –2.0V for periods of up to 20 ns.
SS
See Figure 12. Maximum DC input voltage on pin A9 is +13.0V which may overshoot to 14.0V for periods up to 20 ns.
49.No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second.
50. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum
rating conditions for extended periods may affect device reliability.
Figure 12. Maximum Negative Overshoot Waveform
20 ns
20 ns
+0.8 V
–0.5 V
–2 V
20 ns
Figure 13. Maximum Positive Overshoot Waveform
20 ns
V
CC +2.0 V
V
CC+0.5 V
2.0 V
20 ns
20 ns
Document Number: 002-00948 Rev. *C
Page 47 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
13. Operating Ranges
Table 18. Operating Ranges
Parameter
Industrial Devices
Extended Devices
Range
–40°C to +85°C
–40°C to +125°C
2.50V to 2.75V
3.00V to 3.60V
1.65V to 2.75V
1.65V to 3.6V
Ambient Temperature (TA)
VCC Supply Voltages
VIO Supply Voltages
VCC for 2.6V regulated voltage range (S29CD-J devices)
VCC for 3.3V regulated voltage range (S29CL-J devices)
VIO (S29CD-J devices)
VIO (S29CL-J devices)
Note
51.Operating ranges define those limits between which the functionality of the device is guaranteed.
Document Number: 002-00948 Rev. *C
Page 48 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
14. DC Characteristics
Table 19. DC Characteristic, CMOS Compatible
Parameter Description
Test Conditions
Min
Typ
Max
1.0
–25
35
Unit
µA
Input Load Current
VIN = VSS to VIO, VIO = VIO max
VIN = VSS to VIO, VIO = VIO max
VCC = VCCmax; A9 = 12.5V
ILI
ILIWP
ILIT
WP# Input Load Current
A9, ACC Input Load Current
Output Leakage Current
µA
µA
VOUT = VSS to VCC, VCC = VCC max
ILO
1.0
55
µA
S29CD-J
S29CL-J
45
65
mA
mA
VCC Active Burst Read Current (52)
CE# = VIL, OE# = VIL, 8 Double Word
ICCB
90
VCC Active Asynchronous
Read Current (52)
CE# = VIL, OE# = VIL
1 MHz
ICC1
10
50
mA
mA
VCC Active Program Current
(53, 54, 55)
ICC3
ICC4
ICC5
CE# = VIL, OE# = VIH, ACC = VIH
40
20
VCC Active Erase Current (53, 54, 55) CE# = VIL, OE# = VIH, ACC = VIH
50
60
mA
µA
VCC Standby Current (CMOS)
VCC= VCC max, CE# = VCC 0.3V
VCC Active Current
(Read While Write) (54)
CE# = VIL, OE# = VIL
ICC6
30
90
mA
VCC Reset Current
RESET# = VIL
ICC7
ICC8
IACC
VIL
60
60
µA
µA
mA
V
Automatic Sleep Mode Current
VACC Acceleration Current
Input Low Voltage
VIH = VCC 0.3 V, VIL = VSS 0.3V
ACC = VHH
20
–0.5
0.7 x VIO
–0.2
0.3 x VIO
VCC
Input High Voltage
VIH
V
CLK Input Low Voltage
VILCLK
VIHCLK
VIHCLK
VID
0.3 x VIO
2.75
V
CLK Input High Voltage (CD-J)
CLK Input High Voltage (CL-J)
Voltage for Autoselect
0.7 x VCC
0.7 x VCC
11.5
V
3.6
V
VCC = 2.5V
12.5
V
Output Low Voltage
IOL = 4.0 mA, VCC = VCC min
VOL = 0.4V
VOL
0.45
V
RY/BY#, Output Low Current
Accelerated (ACC pin) High Voltage
Output High Voltage
IOLRB
VHH
8
mA
V
IOH = –2.0 mA, VCC = VCC min
IOH = –100 µA, VCC = VCC min
0.85 x VCC
VIO –0.1
1.6
VOH
V
Low VCC Lock-Out Voltage (54)
VLKO
2.0
V
Notes
52. The I current listed includes both the DC operating current and the frequency dependent component.
CC
53. I active while Embedded Erase or Embedded Program is in progress.
CC
54. Not 100% tested.
55.Maximum I specifications are tested with V = V .
CCmax
CC
CC
Document Number: 002-00948 Rev. *C
Page 49 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
14.1 Zero Power Flash
Figure 14. ICC1 Current vs. Time (Showing Active and Automatic Sleep Currents)
4
3
2
1
0
0
500
1000
1500
2000
2500
3000
3500
4000
Time in ns
Note
56.Addresses are switching at 1 MHz.
Figure 15. Typical ICC1 vs. Frequency
5
4
3
2
1
2.7 V
0
1
2
3
4
5
Frequency in MHz
Document Number: 002-00948 Rev. *C
Page 50 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
15. Test Conditions
Figure 16. Test Setup
Device
Under
Test
C
L
16. Test Specifications
Table 20. Test Specifications
Test Condition
Output Load
All Options
Unit
1 TTL gate
Output Load Capacitance, CL (including jig capacitance)
Input Rise and Fall Times
30
5
pF
ns
V
Input Pulse Levels
0.0V – VIO
VIO/2
VIO/2
Input timing measurement reference levels
Output timing measurement reference levels
V
V
Table 21. Key to Switching Waveforms
Waveform
Inputs
Outputs
Steady
Changing from H to L
Changing from L to H
Don’t Care, Any Change Permitted
Does Not Apply
Changing, State Unknown
Center Line is High Impedance State (High-Z)
16.1 Switching Waveforms
Figure 17. Input Waveforms and Measurement Levels
VIO/2 V
VIO
VIO/2 V
Input
Measurement Level
Output
VSS
Document Number: 002-00948 Rev. *C
Page 51 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
17. AC Characteristics
17.1 V and V Power-up
CC
IO
Table 22. VCC and VIO Power-up
Parameter
tVCS
Description
VCC Setup Time
Test Setup
Min
Speed
Unit
µs
50
50
50
tVIOS
VIO Setup Time
Min
µs
tRSTH
RESET# Low Hold Time
Min
µs
Figure 18. VCC and VIO Power-up Diagram
tVCS
VCC
tVIOS
VIOP
tRSTH
RESET#
17.2 Asynchronous Operations
Table 23. Asynchronous Read Operations
Parameter
Speed Options
Description
Test Setup
Min
Unit
75 MHz 66 MHz 56 MHz 40 MHz
JEDEC Std.
0R
0P
0M
0J/1J
tAVAV
tRC Read Cycle Time (Note 1)
54
54
ns
ns
CE# = VIL
OE# = VIL
tAVQV tACC Address to Output Delay
Max
tELQV
tGLQV
tEHQZ
tCE Chip Enable to Output Delay
OE# = VIL
Max
Max
Max
Min
54
20
10
2
ns
ns
ns
ns
ns
ns
tOE Output Enable to Output Delay
tDF Chip Enable to Output High-Z (Note 57)
tGHQZ
tDF Output Enable to Output High-Z (Note 57)
Max
Min
10
0
Read
Output Enable Hold Time
(Note 57)
tOEH
Toggle and
Data# Polling
Min
Min
10
2
ns
ns
Output Hold Time From Addresses, CE# or
OE#, Whichever Occurs First (Note 57)
tAXQX
tOH
Notes
57. Not 100% tested.
58.See Figure 16 and Table 20 for test specifications.
59. TOE during Read Array.
Document Number: 002-00948 Rev. *C
Page 52 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Figure 19. Conventional Read Operations Timings
tRC
Addresses Stable
tACC
Addresses
CE#
tDF
tOE
OE#
tOEH
WE#
tCE
tOH
High Z
High Z
Output Valid
Outputs
RESET#
RY/BY#
0 V
Figure 20. Asynchronous Command Write Timing
CLK
ADV#
CE#
tCS
tCH
tWC
Stable Address
Addresses
Data
Valid Data
tAH
tAS
tDH
tDS
WE#
OE#
tWEH
tOEP
IND/WAIT#
Notes
60. All commands have the same number of cycles in both asynchronous and synchronous modes, including the READ/RESET command. Only a single array access
occurs after the F0h command is entered. All subsequent accesses are burst mode when the burst mode option is enabled in the Configuration Register.
61.Refer to Table 26 for write timing parameters.
Document Number: 002-00948 Rev. *C
Page 53 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
17.3 Synchronous Operations
Table 24. Burst Mode for 32 Mb and 16 Mb
Parameter
Speed Options
66 MHz, 56 MHz,
Description
Unit
75 MHz,
0R
40 MHz,
JEDEC
Std.
0P 0M
0J/1J
Burst Access Time Valid Clock to Output Delay
ADV# Setup Time to Rising Edge of CLK
ADV# Hold Time from Rising Edge of CLK
ADV# Pulse Width
tBACC
tADVCS
tADVCH
tADVP
Max
Min
Min
Min
Min
Min
Max
Min
Max
Min
Max
Max
Max
Min
Min
Max
Min
Max
Max
Min
Max
8
8
8
8
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
6
1.5
7.5
2
8.5
2
9.5
3
10.5
3
16 Mb
32 Mb
Valid Data Hold from CLK (Note 63)
tBDH
0
0
0
0
CLK to Valid IND/WAIT# (Note 63)
IND/WAIT# Hold from CLK (Note 63)
CLK to Valid Data Out, Initial Burst Access
tINDS
tINDH
tIACC
8
2
2
3
3
48
54
54
54
25
13.3
15.15
17.85
CLK Period
tCLK
60
3
CLK Rise Time (Note 63)
CLK Fall Time (Note 63)
CLK High Time (Note 64)
CLK Low Time (Note 64)
Output Enable to Output Valid
tCR
tCF
ns
ns
ns
ns
ns
ns
3
tCLKH
tCLKL
tOE
6.65
6.65
6.8
6.8
8.0
8.0
11.25
11.25
20
2
2
10
10
4
3
15
15
5
3
17
17
6
Output Enable to Output High-Z (Note 63)
tDF
tOEZ
7.5
7.5
4
Chip Enable to Output High-Z (Note 63)
CE# Setup Time to Clock
tEHQZ
tCEZ
tCES
ns
ns
ns
ADV# Falling Edge to Address Valid (Note 62)
tAAVS
6.5
1
CLK
cycle
Address Hold Time from Rising Edge of ADV#
tAAVH
Min
tRSTZ RESET# Low to Output High-Z (Note 63)
tWADVH1 ADV# Falling Edge to WE# Falling Edge
tWADVH2 ADV# Rising Edge to WE# Rising Edge
tWADVS WE# Rising Edge Setup to ADV# Falling Edge
Max
Min
Min
Min
7.5
10
15
17
ns
ns
ns
ns
0
10
11.75
Notes
62. Using the max t
and min t
specs together will result in incorrect data output.
ADVCS
AAVS
63. Not 100% tested
64.Recommended 50% Duty Cycle
Document Number: 002-00948 Rev. *C
Page 54 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Figure 21. Burst Mode Read (x32 Mode)
tCES
tCEZ
CE#
CLK
tADVCS
ADV#
tAAVH
Aa
Addresses
Data
tBDH
tBACC
Da
Da+1
Da+2
Da + 3
Da + 7
tIACC
tAAVS
tOE
tOEZ
OE#
IND#
tINDS
tINDH
Figure 22. Synchronous Command Write/Read Timing
CE#
tCES
CLK
tADVCS
tADVP
ADV#
Valid Address
Addresses
Valid Address
tWC
Valid Address
tEHQZ
tADVCH
Data In
tWADVH1
Data Out
Data
tDF
tWADVH2
tOE
tDH
OE#
WE#
tDS
tWP
10 ns
tWADVS
IND/WAIT#
Note
65.All commands have the same number of cycles in both asynchronous and synchronous modes, including the READ/RESET command. Only a single array access
occurs after the F0h command is entered. All subsequent accesses are burst mode when the burst mode option is enabled in the Configuration Register.
Document Number: 002-00948 Rev. *C
Page 55 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
17.4 Hardware Reset (RESET#)
Table 25. Hardware Reset (RESET#)
Parameter
All Speed
Options
Description
Test Setup
Unit
JEDEC
Std.
RESET# Pin Low (During embedded Algorithms) to Read or Write
(See Note)
tREADY
Max
Min
11
µs
ns
RESET# Pin Low (Not during embedded Algorithms) to Read or
Write (See Note)
tREADY2
500
RESET# Pulse Width
tRP
tRH
tRPD
tRB
Min
Min
Min
Min
Min
500
50
ns
ns
µs
ns
ns
RESET# High time Before Read (See Note)
RESET# Low to Standby Mode
RY/BY # Recovery Time
20
0
RESET # Active for Bank NOT Executing Algorithm
tREADY3
500
Note
66. Not 100% tested.
Figure 23. RESET# Timings
RY/BY#
CE#, OE#
RESET#
tRH
tRP
tREADY2
Reset Timing to Bank NOT Executing Embedded Algorithm
Reset Timing to Bank Executing Embedded Algorithm
tREADY
RY/BY#
tRB
CE#, OE#
RESET#
tRP
Document Number: 002-00948 Rev. *C
Page 56 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
17.5 Write Protect (WP#)
Figure 24. WP# Timing
Program/Erase Command
Data
WE#
tDS
tDH
tWP
tWPWS
Valid WP#
WP#
tBUSY
tWPRH
RY/BY#
17.6 Erase/Program Operations
Table 26. Erase/Program Operations
Parameter
All Speed
Options
Description
Unit
JEDEC
tAVAX
Std.
tWC
tAS
tAH
tDS
tDH
Write Cycle Time (Note 67)
Address Setup Time
Min
Min
Min
Min
Min
60
0
ns
ns
ns
ns
ns
tAVWL
tWLAX
tDVWH
tWHDX
Address Hold Time from WE# Falling Edge
Data Setup to WE# Rising Edge
11.75
18
Data Hold from WE# Rising Edge
2
Read Recovery Time Before Write
(OE# High to WE# Low, WE# Hold Time) (Note 67)
tGHWL
tWEH
Min
0
ns
OE# Pulse Width (Note 67)
tOEP
tCS
Min
Min
Min
Min
Min
Typ
Typ
Min
Min
Max
Min
Max
16
0
ns
ns
ns
ns
ns
µs
sec.
µs
ns
ns
ns
ns
CE# Setup Time
tELWL
tWHEH
tWLWH
tWHWL
tWHWH1
tWHWH2
CE# Hold Time
tCH
0
WE# Width
tWP
25
30
9
Write Pulse Width High
tWPH
tWHWH1
tWHWH2
tVCS
Programming Operation (Note 68), Double-Word
Sector Erase Operation (Note 68)
VCC Setup Time (Note 67)
0.5
50
0
Recovery Time from RY/BY# (Note 67)
RY/BY# Delay After WE# Rising Edge (Note 67)
WP# Setup to WE# Rising Edge with Command (Note 67)
WP# Hold after RY/BY# Rising Edge (Note 67)
tRB
tBUSY
tWPWS
tWPRH
90
20
2
Notes
67. Not 100% tested.
68.See Command Definitions on page 67 for more information.
69.Program Erase Parameters are the same, regardless of Synchronous or Asynchronous mode.
Document Number: 002-00948 Rev. *C
Page 57 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Figure 25. Program Operation Timings
Program Command Sequence (last two cycles)
Read Status Data (last two cycles)
tAS
tWC
Addresses
555h
PA
PA
PA
CE#
OE#
tCH
tAH
tWHWH1
tWP
WE#
Data
tWPH
tCS
tDS
tDH
tDH
PD
DOUT
A0h
Status
tBUSY
tRB
RY/BY#
VCC
tVCS
Note
70.PA = program address, PD = program data, D
is the true data at the program address.
OUT
Figure 26. Chip/Sector Erase Operation Timings
Erase Command Sequence (last two cycles)
Read Status Data
tAS
SA
tWC
2AAh
VA
VA
Addresses
CE#
555h for chip erase
tCH
OE#
tAH
tWP
WE#
tWPH
tWHWH2
tCS
tDS
tDH
tDH
In
Data
Complete
30h
Progress
10 for Chip Erase
tBUSY
tRB
RY/BY#
VCC
tVCS
Note
71.SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see Write Operation Status on page 32).
Document Number: 002-00948 Rev. *C
Page 58 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Figure 27. Back-to-back Cycle Timings
tWC
Valid PA
tWC
tRC
tWC
Valid PA
tAH
Valid RA
Valid PA
Addresses
tCPH
tACC
tCE
CE#
OE#
tCP
tOE
tOEH
tGHWL
tWP
tWPH
WE#
Data
tDF
tWPH
tDS
tOH
Valid
tDH
Valid
In
Valid
In
Valid
In
Out
tSR/W
WE# Controlled Write Cycle
Read Cycle
CE# Controlled Write Cycles
Figure 28. Data# Polling Timings (During Embedded Algorithms)
‘
tWC
VA
tRC
VA
Addresses
VA
tACC
tCE
CE#
tCH
tOE
OE#
WE#
tOEH
tDF
tOH
High Z
High Z
DQ7
Data
Valid Data
Valid Data
Complement
Complement
True
Status Data
True
Status Data
tBUSY
RY/BY#
Note
72.VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data read cycle.
Document Number: 002-00948 Rev. *C
Page 59 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Figure 29. Toggle Bit Timings (During Embedded Algorithms)
tRC
Addresses
CE#
VA
tACC
tCE
VA
VA
VA
tCH
tOE
OE#
WE#
tOEH
tDF
tOH
High Z
DQ6/DQ2
RY/BY#
Valid Status
(first read)
Valid Status
Valid Status
Valid Data
(second read)
(stops toggling)
tBUSY
Note
73.VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status read cycle, and array data read cycle.
Figure 30. DQ2 vs. DQ6 for Erase/Erase Suspend Operations
Enter Embedded
Erasing
Erase
Suspend
Enter Erase
Suspend Program
Erase
Resume
WE#
Erase Suspend
Read
Erase Suspend
Program
Erase Suspend
Read
Erase
Erase
Erase
Complete
DQ6
DQ2
Note
74.The system may use CE# or OE# to toggle DQ2 and DQ6. DQ2 toggles only when read at an address within an erase-suspended sector.
Figure 31. Synchronous Data Polling Timing/Toggle Bit Timings
CE#
CLK
ADV#
Addresses
OE#
VA
VA
tOE
tOE
Data
Status Data
Status Data
RDY
Notes
75.The timings are similar to synchronous read timings and asynchronous data polling Timings/Toggle bit Timing.
76. VA = Valid Address. Two read cycles are required to determine status. When the Embedded Algorithm operation is complete, the toggle bits will stop toggling.
77.RDY is active with data (A18 = 0 in the Configuration Register). When A18 = 1 in the Configuration Register, RDY is active one clock cycle before data.
78.Data polling requires burst access time delay.
Document Number: 002-00948 Rev. *C
Page 60 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Figure 32. Sector Protect/Unprotect Timing Diagram
V
IH
RESET#
SA, A6,
A1, A0
Valid*
Valid*
Valid*
Sector Protect/Unprotect
Verify
Data
60h
60h/68h**
40h/48h***
Status
Sector Protect: 150 µs
Sector Unprotect: 15 ms
1 µs
CE#
WE#
OE#
Notes
79.* Valid address for sector protect: A[7:0] = 3Ah. Valid address for sector unprotect: A[7:0] = 3Ah.
** Command for sector protect is 68h. Command for sector unprotect is 60h.
*** Command for sector protect verify is 48h. Command for sector unprotect verify is 40h.
Document Number: 002-00948 Rev. *C
Page 61 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
17.7 Alternate CE# Controlled Erase/Program Operations
Table 27. Alternate CE# Controlled Erase/Program Operations
Parameter
Description
All Speed Options
Unit
JEDEC
tAVAV
Std.
tWC
tAS
Write Cycle Time (Note 80)
Address Setup Time
Address Hold Time
Data Setup Time
Min
Min
Min
Min
Min
Min
Min
Min
Min
Min
Min
Min
Typ
Typ
Min
65
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
sec
ns
tAVEL
tELAX
tDVEH
tAH
tDS
45
35
2
16 Mb
32 Mb
tEHDX
tDH
Data Hold Time
5
tGHEL
tWLEL
tEHWH
tGHEL
tWS
tWH
tWP
Read Recovery Time Before Write (OE# High to WE# Low)
0
WE# Setup Time
WE# Hold Time
WE# Width
0
0
25
20
30
9
tELEH
tEHEL
tWHWH1
tWHWH2
tCP
CE# Pulse Width
CE# Pulse Width High
tCPH
tWHWH1 Programming Operation (Note 81)
tWHWH2 Sector Erase Operation (Note 81)
Double-Word
0.5
5
tWCKS
WE# Rising Edge Setup to CLK Rising Edge
Notes
80. Not 100% tested.
81.See Command Definitions on page 67 for more information.
Figure 33. Alternate CE# Controlled Write Operation Timings
555 for program
2AA for erase
PA for program
SA for sector erase
555 for chip erase
Data# Polling
PA
Addresses
tAS
tWC
tAH
tWH
tWP
WE#
OE#
tWPH
tGHEL
tWHWH1 or 2
tCP
CE#
Data
tWS
tCPH
tBUSY
tDS
tDH
DQ7#
DOUT
tRH
A0 for program
55 for erase
PD for program
30 for sector erase
10 for chip erase
RESET#
RY/BY#
Notes
82. PA = program address, PD = program data, DQ7# = complement of the data written to the device, D
= data written to the device.
OUT
83. Figure indicates the last two bus cycles of the command sequence.
Document Number: 002-00948 Rev. *C
Page 62 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
17.8 Erase and Programming Performance
Table 28. Erase and Programming Performance
Parameter
Sector Erase Time
Typ (Note 84) Max (Note 85)
Unit
Comments
0.5
5
s
Excludes 00h programming prior to erasure
(Note 87)
16 Mb = 23
32 Mb = 46
16 Mb = 230
32 Mb = 460
Chip Erase Time
s
Double Word Program Time
8
8
130
130
µs
µs
Accelerated Double Word Program Time
16 Mb = 5
32 Mb = 10
16 Mb = 50
32 Mb = 100
Excludes system level overhead (Note 88)
Accelerated Chip Program Time
Chip Program Time, x32 (Note 86)
s
s
16 Mb = 12
32 Mb = 24
16 Mb = 120
32 Mb = 240
Notes
84.Typical program and erase times assume the following conditions: 25°C, 2.5V V , 100K cycles. Additionally, programming typicals assume checkerboard pattern.
CC
85.Under worst case conditions of 145°C, V = 2.5V, 1M cycles.
CC
86. The typical chip programming time is considerably less than the maximum chip programming time listed.
87. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure.
88.System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Table 34 and Table 35 for further
information on command definitions.
89. PPBs have a program/erase cycle endurance of 100 cycles.
90.Guaranteed cycles per sector is 100K minimum.
17.9 PQFP and Fortified BGA Pin Capacitance
Table 29. PQFP and Fortified BGA Pin Capacitance
Parameter Symbol
Parameter Description
Input Capacitance
Test Setup
VIN = 0
Typ
6
Max
7.5
12
9
Unit
pF
CIN
COUT
CIN2
Output Capacitance
Control Pin Capacitance
VOUT = 0
VIN = 0
8.5
7.5
pF
pF
Notes
91.Sampled, not 100% tested.
92. Test conditions T = 25°C, f = 1.0 MHz.
A
Document Number: 002-00948 Rev. *C
Page 63 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
18. Appendix 1
18.1 Common Flash Memory Interface (CFI)
The Common Flash Interface (CFI) specification outlines device and host system software interrogation handshake, which allows
specific vendor-specified software algorithms to be used for entire families of devices. Software support can then be device-
independent, JEDEC ID-independent, and forward- and backward-compatible for the specified flash device families. Flash vendors
can standardize existing interfaces for long-term compatibility.
This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address 55h in word mode (or
address AAh in byte mode), any time the device is ready to read array data. The system can read CFI information at the addresses
given in Table 30-Table 32. In order to terminate reading CFI data, the system must write the reset command.
The system can also write the CFI query command when the device is in the autoselect mode. The device enters the CFI query
mode, and the system can read CFI data at the addresses given in Table 30-Table 32. The system must write the reset command to
return the device to the autoselect mode.
For further information, please refer to the CFI Specification and CFI Publication 100. Contact a Cypress representative for copies of
these documents.
Table 30. CFI Query Identification String
Addresses
Data
Description
10h
11h
12h
0051h
0052h
0059h
Query Unique ASCII string QRY
13h
14h
0002h
0000h
Primary OEM Command Set
15h
16h
0040h
0000h
Address for Primary Extended Table
17h
18h
0000h
0000h
Alternate OEM Command Set (00h = none exists)
Address for Alternate OEM Extended Table (00h = none exists)
19h
1Ah
0000h
0000h
Table 31. CFI System Interface String
Addresses
Data
Description
VCC Min. (write/erase)
DQ7–DQ4: volts, DQ3–DQ0: 100 millivolt
1Bh
(see description)
0025h = S29CD-J devices
0030h = S29CL-J devices
VCC Max. (write/erase)
DQ7–DQ4: volts, DQ3–DQ0: 100 millivolt
1Ch
(see description)
0027h = S29CD-J devices
0036h = S29CL-J devices
1Dh
1Eh
1Fh
20h
21h
22h
23h
24h
25h
26h
0000h
0000h
0004h
0000h
0009h
0000h
0005h
0000h
0007h
0000h
VPP Min. voltage (00h = no VPP pin present)
VPP Max. voltage (00h = no VPP pin present)
Typical timeout per single word/doubleword program 2N µs
Typical timeout for Min. size buffer program 2N µs (00h = not supported)
Typical timeout per individual block erase 2N ms
Typical timeout for full chip erase 2N ms (00h = not supported)
Max. timeout for word/doubleword program 2N times typical
Max. timeout for buffer write 2N times typical
Max. timeout per individual block erase 2N times typical
Max. timeout for full chip erase 2N times typical (00h = not supported)
Document Number: 002-00948 Rev. *C
Page 64 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Table 32. Device Geometry Definition
Addresses
Data
Description
Device Size = 2N byte
0015h = 16 Mb device
0016h = 32 Mb device
27h
(see description)
Flash Device Interface description (for complete description, please refer to CFI publication 100)
0000 = x8-only asynchronous interface
0001 = x16-only asynchronous interface
0002 = supports x8 and x16 via BYTE# with asynchronous interface
0003 = x 32-only asynchronous interface
28h
29h
0003h
0000h
0005 = supports x16 and x32 via WORD# with asynchronous interface
2Ah
2Bh
0000h
0000h
Max. number of byte in multi-byte program = 2N
(00h = not supported)
2Ch
0003h
Number of Erase Block Regions within device
2Dh
2Eh
2Fh
30h
0007h
0000h
0020h
0000h
Erase Block Region 1 Information
(refer to the CFI specification or CFI publication 100)
Erase Block Region 2 Information
31h
32h
33h
34h
(See description)
0000h
(refer to the CFI specification or CFI publication 100)
Address 31h data:
001Dh = 16 Mb device
003Dh = 32 Mb device
0000h
0001h
35h
36h
37h
38h
0007h
0000h
0020h
0000h
Erase Block Region 3 Information
(refer to the CFI specification or CFI publication 100)
39h
3Ah
3Bh
3Ch
0000h
0000h
0000h
0000h
Erase Block Region 4 Information
(refer to the CFI specification or CFI publication 100)
Table 33. CFI Primary Vendor-Specific Extended Query
Addresses
Data
Description
40h
41h
42h
0050h
0052h
0049h
Query-unique ASCII string PRI
43h
44h
0031h
0033h
Major version number, ASCII (reflects modifications to the silicon)
Minor version number, ASCII (reflects modifications to the CFI table)
Address Sensitive Unlock (DQ1, DQ0)
00 = Required, 01 = Not Required
Silicon Revision Number (DQ5–DQ2)
0000 = CS49
45h
000Ch
0001 = CS59
0010 = CS99
0011 = CS69
0100 = CS119
Erase Suspend (1 byte)
00 = Not Supported
01 = To Read Only
46h
0002h
02 = To Read and Write
Sector Protect (1 byte)
47h
48h
0001h
0000h
00 = Not Supported, X = Number of sectors in per group
Temporary Sector Unprotect
00h = Not Supported, 01h = Supported
Document Number: 002-00948 Rev. *C
Page 65 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Table 33. CFI Primary Vendor-Specific Extended Query (Continued)
Addresses
Data
Description
Sector Protect/Unprotect scheme (1 byte)
01 =29F040 mode, 02 = 29F016 mode
03 = 29F400 mode, 04 = 29LV800 mode
49h
0006h
05 = 29BDS640 mode (Software Command Locking)
06 = BDD160 mode (New Sector Protect)
07 = 29LV800 + PDL128 (New Sector Protect) mode
Simultaneous Read/Write (1 byte)
4Ah
4Bh
4Ch
4Dh
4Eh
0037h
0001h
0000h
00B5h
00C5h
00h = Not Supported, X = Number of sectors in all banks except Bank 1
Burst Mode Type
00h = Not Supported, 01h = Supported
Page Mode Type
00h = Not Supported, 01h = 4 Word Page, 02h = 8 Word Page
ACC (Acceleration) Supply Minimum
00h = Not Supported (DQ7-DQ4: volt in hex, DQ3-DQ0: 100 mV in BCD)
ACC (Acceleration) Supply Maximum
00h = Not Supported, (DQ7-DQ4: volt in hex, DQ3-DQ0: 100 mV in BCD)
Top/Bottom Boot Sector Flag (1 byte)
00h = Uniform device, no WP# control,
01h = 8 x 8 Kb sectors at top and bottom with WP# control
02h = Bottom boot device
4Fh
0001h
03h = Top boot device
04h = Uniform, Bottom WP# Protect
05h = Uniform, Top WP# Protect
If the number of erase block regions = 1, then ignore this field
Program Suspend
00 = Not Supported
01 = Supported
50h
51h
57h
0001h
0000h
0002h
Write Buffer Size
2(N+1) word(s)
Bank Organization (1 byte)
00 = If data at 4Ah is zero
XX = Number of banks
Bank 1 Region Information (1 byte)
XX = Number of Sectors in Bank 1
58h
59h
5Ah
5Bh
0017h
0037h
0000h
0000h
Bank 2 Region Information (1 byte)
XX = Number of Sectors in Bank 2
Bank 3 Region Information (1 byte)
XX = Number of Sectors in Bank 3
Bank 4 Region Information (1 byte)
XX = Number of Sectors in Bank 4
Document Number: 002-00948 Rev. *C
Page 66 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
19. Appendix 2
19.1 Command Definitions
Table 34. Memory Array Command Definitions (x32 Mode)
Bus Cycles (Notes 93–96)
Third Fourth
Command (Notes)
First
Second
Fifth
Addr
Sixth
Addr Data Addr Data
Addr
Data
Addr
Data
Data
Addr
Data
Read (97)
1
1
4
6
4
6
6
1
1
1
2
RA
XXX
555
555
555
555
555
BA
RD
F0
AA
AA
AA
AA
AA
B0
30
Reset (98)
Manufacturer ID
Device ID (100)
2AA
2AA
2AA
2AA
2AA
55
55
55
55
55
555
555
555
555
555
90
90
A0
80
80
BA+X00
BA+X01
PA
01
7E
PD
AA
AA
Autoselect
(99)
BA+X0E
09
BA+X0F
00/01
Program
Chip Erase
Sector Erase
555
2AA
2AA
55
55
555
SA
10
30
555
Program/Erase Suspend (101)
Program/Erase Resume (102)
CFI Query (103, 104)
BA
55
98
Accelerated Program (105)
XX
A0
PA
PD
55
Configuration Register Verify
(104)
3
4
555
555
AA
AA
2AA
BA+555
C6
BA+XX
XX
RD
Configuration Register Write
(106)
2AA
55
555
555
D0
20
WD
Unlock Bypass Entry (107)
Unlock Bypass Program (107)
Unlock Bypass Erase (107)
Unlock Bypass CFI (103, 107)
Unlock Bypass Reset (107)
3
2
2
1
2
555
XX
XX
XX
XX
AA
A0
80
98
90
2AA
PA
55
PD
10
XX
XX
00
Legend
BA = Bank Address. The set of addresses that comprise a bank. The system
may write any address within a bank to identify that bank for a command.
PA = Program Address (Amax–A0). Addresses latch on the falling edge of the
WE# or CE# pulse, whichever happens later.
RA = Read Address (Amax–A0).
RD = Read Data. Data DQmax–DQ0 at address location RA.
SA = Sector Address. The set of addresses that comprise a sector. The system
may write any address within a sector to identify that sector for a command.
WD = Write Data. See “Configuration Register” definition for specific write data.
Data latched on rising edge of WE#.
PD = Program Data (DQmax–DQ0) written to location PA. Data latches on the
rising edge of WE# or CE# pulse, whichever happens first.
X = Don’t care
Notes
93.See Table 5 for description of bus operations.
94. All values are in hexadecimal.
100.The device ID must be read across the fourth, fifth, and sixth cycles. 00h in
the sixth cycle indicates ordering option 00, 01h indicates ordering option 01.
101.The system may read and program in non-erasing sectors when in the
Program/Erase Suspend mode. The Program/Erase Suspend command is
valid only during a sector erase operation, and requires the bank address.
95. Shaded cells in table denote read cycles. All other cycles are write
operations.
96.During unlock cycles, (lower address bits are 555 or 2AAh as shown in table)
address bits higher than A11 (except where BA is required) and data bits
higher than DQ7 are don’t cares.
102.The Program/Erase Resume command is valid only during the Erase
Suspend mode, and requires the bank address.
103.Command is valid when device is ready to read array data.
104.Asynchronous read operations.
97. No unlock or command cycles required when bank is reading array data.
98. The Reset command is required to return to the read mode (or to the erase-
suspend-read mode if previously in Erase Suspend) when a bank is in the
autoselect mode, or if DQ5 goes high (while the bank is providing status
information).
105.ACC must be at V during the entire operation of this command.
ID
106.Command is ignored during any Embedded Program, Embedded Erase, or
Suspend operation.
99.The fourth cycle of the autoselect command sequence is a read cycle. The
system must provide the bank address to obtain the manufacturer ID or
device ID information. See Autoselect on page 26 for more information.
107.The Unlock Bypass Entry command is required prior to any Unlock Bypass
operation. The Unlock Bypass Reset command is required to return to the
read mode.
Document Number: 002-00948 Rev. *C
Page 67 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Table 35. Sector Protection Command Definitions (x32 Mode)
Bus Cycles (Notes 108–111)
Third Fourth
Command (Notes)
First
Addr
Second
Addr
Fifth
Addr
Sixth
Data
F0
Data
Addr
Data
Addr
Data
Data
Addr
Data
Reset
1
3
4
XXX
555
555
Secured Silicon Sector Entry
Secured Silicon Sector Exit
AA
2AA
2AA
55
55
555
555
88
90
AA
XX
00
68
Secured Silicon Protection
Bit Program (112, 113)
6
6
555
555
AA
AA
2AA
2AA
55
55
555
555
60
60
OW
OW
48
OW
RD(0)
Secured Silicon Protection Bit
Status
OW
RD(0)
Password Program (112, 114, 115)
Password Verify
4
4
5
6
6
4
3
4
4
4
4
6
6
6
6
555
555
555
555
555
555
555
555
555
555
555
555
555
555
555
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
2AA
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
555
555
38
C8
28
60
60
90
78
58
48
48
58
60
60
60
60
PWA[0-1]
PWA[0-1]
PWA[0-1]
SG+WP
WP
PWD[0-1]
PWD[0-1]
PWD[0-1]
68
Password Unlock (114, 115)
PPB Program (112, 113)
All PPB Erase (112, 116, 117)
PPB Status (118, 119)
PPB Lock Bit Set
555
555
SG+WP
WP
48
40
SG+WP RD(0)
555
60
WP
RD(0)
BA+555
555
SA+X02
00/01
PPB Lock Bit Status
BA+555
555
SA
SA
SA
SA
PL
PL
SL
SL
RD(1)
X1
DYB Write (114)
DYB Erase (114)
555
X0
DYB Status (119)
BA+555
555
RD(0)
68
PPMLB Program (112, 113)
PPMLB Status (112)
PL
SL
48
48
PL
SL
RD(0)
RD(0)
555
RD(0)
68
SPMLB Program (112, 113)
SPMLB Status (112)
555
555
RD(0)
Legend
DYB = Dynamic Protection Bit
OW = Address (A5–A0) is (011X10).
PPB = Persistent Protection Bit
SA = Sector Address. The set of addresses that comprise a sector. The system may
write any address within a sector to identify that sector for a command.
SG = Sector Group Address
BA = Bank Address. The set of addresses that comprise a bank. The system may write
any address within a bank to identify that bank for a command.
SL = Persistent Protection Mode Lock Address (A5–A0) is (010X10)
WP = PPB Address (A5–A0) is (111010)
PWA = Password Address. A0 selects between the low and high 32-bit portions
of the 64-bit Password
PWD = Password Data. Must be written over two cycles.
PL = Password Protection Mode Lock Address (A5–A0) is (001X10)
RD(0) = Read Data DQ0 protection indicator bit. If protected, DQ0= 1, if
unprotected, DQ0 = 0.
X = Don’t care
PPMLB = Password Protection Mode Locking Bit
RD(1) = Read Data DQ1 protection indicator bit. If protected, DQ1 = 1, if
unprotected, DQ1 = 0.
SPMLB = Persistent Protection Mode Locking Bit
Notes
108.See Table 5 for description of bus operations.
109.All values are in hexadecimal.
115.The entire four bus-cycle sequence must be entered for each portion of the
password.
116.The fourth cycle erases all PPBs. The fifth and sixth cycles are used to validate
whether the bits have been fully erased. If DQ0 (in the sixth cycle) reads 1, the
erase command must be issued and verified again.
110.Shaded cells in table denote read cycles. All other cycles are write
operations.
111.During unlock cycles, (lower address bits are 555 or 2AAh as shown in table)
address bits higher than A11 (except where BA is required) and data bits
higher than DQ7 are don’t cares.
117.Before issuing the erase command, all PPBs should be programmed in order to
prevent over-erasure of PPBs.
118.In the fourth cycle, 00h indicates PPB set; 01h indicates PPB not set.
112.The reset command returns the device to reading the array.
119.The status of additional PPBs and DYBs may be read (following the fourth cycle)
without reissuing the entire command sequence.
113.The fourth cycle programs the addressed locking bit. The fifth and sixth
cycles are used to validate whether the bit has been fully programmed. If
DQ0 (in the sixth cycle) reads 0, the program command must be issued and
verified again.
114.Data is latched on the rising edge of WE#.
Document Number: 002-00948 Rev. *C
Page 68 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
20. Revision History
Document Title: S29CD032J, S29CD016J, S29CL032J, S29CL016J, 32/16 Mbit, 2.6/3.3 V, Dual Boot, Simultaneous Read/
Write, Burst Flash
Document Number: 002-00948
Orig. of
Change
Submission
Date
Rev.
ECN No.
Description of Change
Spansion Publication Number: S29CD-J_CL-J_00
03/01/2005
04/15/2005
A0:Initial release
A1:Ordering Information and Valid Combinations tables
Updated to include lead Pb-free options.
Ordering Information
Added “Contact factory” for 75 MHz. Modified Ordering Options for Characters 15 and
16 to reflect
autoselect ID and top/bottom boot. Changed “N” for Extended Temperature Range to
“M”.
Input/Output Descriptions Removed Logic Symbol Diagrams.
Additional Resources Added section.
Memory Address Map Changed “Bank 2” to “Bank 1”.
Simultaneous Read/Write Operation Removed Ordering Options Table (Tables 3 and
4).
Advanced Sector Protection/Unprotection
Added Advanced Sector Protection/Unprotection figure. Added figures for PPB Erase
and Program
Algorithm.
Electronic Marking Added in Electronic Marking section.
Absolute Maximum Ratings
Modified VCC Ratings to reflect 2.6 V and 3.6 V devices. Modified VCC Ratings to
reflect 16 Mb and
32 Mb devices.
**
-
AC Characteristics Added Note “tOE during Read Array”.
Asynchronous Read Operation Changed values of tAVAV, tAVQV, tELQV, tGLQV in
RYSU
01/20/2006 table.
Conventional Read Operation Timings Moved tDF line to 90% on the high-Z output
in figure.
Burst Mode Read for 32 Mb and 16 Mb
Added tAAVS and tAAVH timing parameters to table. Changed tCH to tCLKH. Changed
tCL to tCLKL.
Removed the following timing parameters:
• tDS (Data Setup to WE# Rising Edge)
• tDH (Data Hold from WE# Rising Edge)
• tAS (Address Setup to Falling Edge of WE#)
• tAH (Address Hold from Falling Edge of WE#)
• tCS (CE# Setup Time)
• tCH (CE# Hold Time)
• tACS (Address Setup Time to CLK)
• tACH (Address Hold Time from ADV# Rising Edge of CLK while ADV# is Low)
Burst Mode Read (x32 Mode)
Added the following timing parameters:
• tAAVS
• tDVCH
• tINDS
• tINDH
Document Number: 002-00948 Rev. *C
Page 69 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Document Title: S29CD032J, S29CD016J, S29CL032J, S29CL016J, 32/16 Mbit, 2.6/3.3 V, Dual Boot, Simultaneous Read/
Write, Burst Flash
Document Number: 002-00948
Orig. of
Change
Submission
Date
Rev.
ECN No.
Description of Change
Asynchronous Command Write Timing In figure, changed tOEH to tWEH; changed
tWPH to tOEP.
Synchronous Command Write/Read Timing
Removed tWADVH and tWCKS from figure.
WP# Timing In figure, changed tCH to tBUSY
Erase/Program Operations
01/20/2006
In table, added Note 3: Program/Erase parameters are the same regardless of syn-
chronous or
asynchronous mode. Added tOEP (OE# High Pulse)
Alternative CE# Controlled Erase/Program Operations
Removed tOES from table. Added tWADVS and tWCKS
Appendix 2: Command Definitions Removed “or when device is in autoselect mode”
from Note 14.
Global Changed document status to Preliminary.
Distinctive Characteristics Changed cycling endurance from typical to guaranteed.
Performance Characteristics Updated Max Asynch. Access Time, Max CE# Access
Time, and Max OE# Access time in table.
Ordering Information Updated additional ordering options in designator breakout table.
Updated valid combination tables.
Input/Output Descriptions and Logic Symbols
Changed RY/BY# description.
Physical Dimensions/Connection Diagrams
Changed note on connection diagrams.
Additional Resources Updated contact information.
Hardware Reset (RESET#) Added section.
Autoselect Updated third and fourth paragraphs in section. Updated Autoselect Codes
table.
Erase Suspend / Erase Resume Commands
**
-
RYSU
Modified second paragraph. Replaced allowable operations table with bulleted list.
Program Suspend / Program Resume Commands
Replaced allowable operations table with bulleted list.
Reset Command Added section.
06/12/2006
Secured Silicon Sector Flash Memory Region
Modified Secured Silicon Sector Addresses table.
Absolute Maximum Ratings Modified VCC and VIO ratings. Modified Note 1.
Operating Ranges Modified specification titles and descriptions (no specification value
changes).
DC Characteristics, CMOS Compatible table
Modified ICCB specification. Deleted Note 5. Added Note 3 references to table.
Burst Mode Read for 32 Mb and 16 Mb table
Modified tADVCS, tCLKH, tCLKL, tAAVS specifications. Added tRSTZ, tWADVH1, and
tWADVH2 specifications. Added Notes 2 and 3, and note references to table.
Synchronous Command Write/Read Timing figure
Added tWADVH1 and tWADVH2 to figure. Deleted tACS and tACH from figure.
Hardware Reset (RESET#) Added table to section.
Erase/Program Operations table Added note references. Deleted tOEP specification.
Erase and Programming Performance Changed Double Word Program Time specifi-
cation.
Common Flash Memory Interface (CFI)
CFI System Interface String table: Changed description and data for addresses 1Bh
and 1Ch.
06/12/2006
Device Geometry Definition table: Changed description and data for address 27h.
Document Number: 002-00948 Rev. *C
Page 70 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Document Title: S29CD032J, S29CD016J, S29CL032J, S29CL016J, 32/16 Mbit, 2.6/3.3 V, Dual Boot, Simultaneous Read/
Write, Burst Flash
Document Number: 002-00948
Orig. of
Change
Submission
Date
Rev.
ECN No.
Description of Change
Global Data sheet format reorganized.
Distinctive Characteristics Changed cycling endurance specification to typical.
Performance Characteristics Changed tBACC specifications for 66 MHz, 56 MHz, 40
MHz speed options.
Ordering Information Added quantities to packing type descriptions, restructured
table for easier reference.
S29CD-J and S29CL-J Flash Family Autoselect Codes (High Voltage
Method)
In table, modified description of read cycle 3 DQ7–DQ0.
DQ6 and DQ2 Indications In table, corrected third column heading
Section 8.9, Reset Command Added table.
09/27/2006
Section 13.1, Absolute Maximum Ratings
Deleted OE# from section.
Table 18.3, Burst Mode Read for 32 Mb and 16 Mb
In table, changed tADVCS, tBDH specifications. Modified description for tIACC.
Deleted minimum
specifications for tAAVH.
Burst Mode Read (x32 Mode) In figure, modified period for tIACC in drawing.
Distinctive Characteristics Corrected number of 16K sectors in 16 Mb devices. Mod-
ified read access times table.
Ordering Information
Changed boot sector option part number designators. Changed valid combinations.
Modified 10th
character option descriptions.
**
-
RYSU
Block Diagram Deleted WORD# input.
2-, 4-, 8- Double Word Linear Burst Operation
In 32- Bit Linear and Burst Data Order table, deleted reference to WORD# input.
Sector Erase Modified second paragraph; added reference to application note.
Advanced Sector Protection/ Unprotection
Modified Advanced Sector Protection/Unprotection figure and notes. In some subsec-
tions, changed
“sector” to “sector group”.
DC Characteristics Changed ICCB test conditions and ICC1 maximum specification.
Test Specifications Changed CL.
03/07/2007
Asynchronous Operations
Asynchronous Command Write Timing figure: Added note.
Asynchronous Read Operations table: Changed tRC, tACC, tCE for 75 MHz device.
Synchronous Operations
Burst Mode Read for 32 Mb and 16 Mb table: Changed tINDS, tCLKL, tAAVH, and
tWADVH1
specifications.
Burst Mode Read figure: Modified period lengths for several specifications.
Erase/Program Operations Added tWEH and tOEP specifications to table.
Latchup Characteristics Deleted section.
Common Flash Memory Interface (CFI)
CFI System Interface String table: Modified description of address 1Bh.
CFI Primary Vendor-Specific Extended Query table: Modified data at address 45h.
Document Number: 002-00948 Rev. *C
Page 71 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Document Title: S29CD032J, S29CD016J, S29CL032J, S29CL016J, 32/16 Mbit, 2.6/3.3 V, Dual Boot, Simultaneous Read/
Write, Burst Flash
Document Number: 002-00948
Orig. of
Change
Submission
Date
Rev.
ECN No.
Description of Change
Global
Removed “Preliminary”
Changed all instances of VCCQ to VIO
Distinctive Characteristics Removed “or without” (wrap around) from Programmable
Burst Interface bullet
Performance Characteristics Added notice to refer to programming best practices
application note for 32 Mb devices.
Ordering Information
Added S29CL032J to valid OPN diagram.
Corrected valid combinations table.
Input/Output Descriptions and Logic Symbols
Subscript CC for VCC, IO for VIO, SS for VSS in table.
Changed type for VIO to “Supply”
Changed type for VSS to “Supply”
Block Diagram
Removed DQmax-DQ0 label from inputs to Burst Address Counter and Address Latch.
Removed Amax-A0 label from I/O Buffers.
Table: S29CD016J/CL016J (Top Boot) Sector and Memory Address Map
Changed Note 2 to refer to Bank 0 and 1 instead of Bank 1 and 2.
Table: 32-Bit Linear and Burst Data Order
03/30/2009
Removed “x16”
Removed “A0:A-1” from Output Data Sequence column for Four Linear Data Transfers.
Removed “A1:A-1” from Output Data Sequence column for Eight Linear Data Transfers.
Programming Added notice to refer to programming best practices application note for
32 Mb devices.
Table: DC Characteristic, CMOS Compatible
Changed Max ICCB for S29CL-J to 90 mA.
Table: Burst Mode for 32 Mb and 16 Mb
Corrected values for tBDH with separate values for 16Mb and 32Mb.
Added tWADVS parameter to table.
**
-
RYSU
Figure: Synchronous Command Write/ Read Timing
Added timing definition for tWADVS.
Table: Erase/Program Operations
Appended “from WE# Rising Edge” to tAH description.
Changed tAH Min to 11.75 ns.
Figure: Program Operation Timings Updated timing diagram to reflect new tAH
value.
Figure: Chip/Sector Erase Operation Timings
Updated timing diagram to reflect new tAH value.
Table: Alternate CE# Controlled Erase/Program Operations
Removed tWADVS parameter.
Product Overview Removed “or without”.
Table: Device Bus Operation Changed “X” to “H” under CLK column for CE# row.
Accelerated Program and Erase Operations
Removed all mention of accelerated erase.
Unlock Bypass Removed mention of unlock bypass sector erase.
Simultaneous Read/Write Added in warning to indicate restrictions on Simultaneous
03/30/2009 Read/Write conditions.
VCC and VIO Power-up And Powerdown Sequencing
Added reference to timing section.
Standby Mode Changed Vcc ± 0.2V to Vcc ± 10%.
Figure: Test Setup Removed Note “Diodes are IN3064 or equivalent”.
Table: Alternate CE# Controlled Erase/Program Operations
Corrected values for tDH with separate values for 16 Mb and 32 Mb.
Table: Memory Array Command Definitions (x32 Mode)
Cleaned up Notes.
Document Number: 002-00948 Rev. *C
Page 72 of 74
S29CD032J
S29CD016J
S29CL032J
S29CL016J
Document Title: S29CD032J, S29CD016J, S29CL032J, S29CL016J, 32/16 Mbit, 2.6/3.3 V, Dual Boot, Simultaneous Read/
Write, Burst Flash
Document Number: 002-00948
Orig. of
Change
Submission
Date
Rev.
ECN No.
Description of Change
Absolute Maximum Ratings
Corrected Address, Data, Control Signals identifiers to correctly distinguish different
ratings
between CL016L, CL032J, CD016J, and CD032J.
DC Characteristics Added line item to distinguish VIHCLK value differences between
CL-J and CD-J.
Synchronous Operation
Corrected Figure “Burst Mode Read (x32 Mode)” to reflect max linear burst length of 8
10/30/2009 double words
instead of 32.
Hardware Reset (RESET#)
Corrected Table “Burst Initial Access Delay”: changed tREADY2, tRP, and tREADY3
set up to Min
instead of Max.
Corrected Figure “RESET# Timings” to add tREADY2 to timing diagram for bank not
executing
embedded algorithm.
Physical Dimensions/Connection Diagrams
05/25/2011
On the 80-ball Fortified BGA Connection Diagram, corrected the K1 pin name from
VCCQ to VIO.
**
-
RYSU
Global Added LAD080 Fortified BGA package option and drawing.
03/15/2012 Additional Resources Updated relevant application note links.
Revision History Corrected heading for May 25, 2011 edits from revision B4 to B5.
Valid Combinations
Updated Valid Combinations table to add clarity and make explicit which offerings
require a
customer to “contact factory for availability”.
Asynchronous Operations
In Figure 18.3, “Asynchronous Command Write Timing”, corrected the tWC measure-
ment to be of
the Stable Address period, not the Valid Data period.
10/11/2012
Erase/Program Operations
In Table 18.5, “Erase/Program Operations”, corrected JEDEC symbol tAVAV to tAVAX.
In Table 18.5, merged redundant rows tGHWL and tWEH.
In Figures 18.8 “Program Operation Timings” and 18.9 “Chip/Sector Erase Operation
Timings”,
corrected tAH measurement to be from the falling edge of WE#.
*A
*B
5048814
5741593
RYSU
12/16/2015 Updated to Cypress template
AESATMP7
05/18/2017 Updated Cypress Logo and Copyright.
Updated template.
11/08/2017 Removed “Preliminary” document status.
Removed Section 6. Additional Resources.
*C
5875054
NFB
Document Number: 002-00948 Rev. *C
Page 73 of 74
S29CD032J
S29CD016J
S29CL032J
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
PSoC® Solutions
ARM® Cortex® Microcontrollers
cypress.com/arm
cypress.com/automotive
cypress.com/clocks
cypress.com/interface
cypress.com/iot
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6
Automotive
Cypress Developer Community
Clocks & Buffers
Interface
Forums | WICED IOT Forums | Projects | Video | Blogs |
Training | Components
Internet of Things
Memory
Technical Support
cypress.com/memory
cypress.com/mcu
cypress.com/support
Microcontrollers
PSoC
cypress.com/psoc
cypress.com/pmic
cypress.com/touch
cypress.com/usb
Power Management ICs
Touch Sensing
USB Controllers
Wireless Connectivity
cypress.com/wireless
© Cypress Semiconductor Corporation, 2005-2017. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document,
including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries
worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other
intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress
hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to
modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users
(either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as
provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation
of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent
permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any
product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is
the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products
are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or
systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the
device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device or system whose failure to perform can be reasonably
expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim,
damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other
liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in
the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 002-00948 Rev. *C
Revised November 08, 2017
Page 74 of 74
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明