STK14CA8-N45G [CYPRESS]
Non-Volatile SRAM, 128KX8, 45ns, CMOS, PDSO32, 0.300 INCH, PLASTIC, SOIC-32;型号: | STK14CA8-N45G |
厂家: | CYPRESS |
描述: | Non-Volatile SRAM, 128KX8, 45ns, CMOS, PDSO32, 0.300 INCH, PLASTIC, SOIC-32 静态存储器 光电二极管 内存集成电路 |
文件: | 总17页 (文件大小:229K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
STK14CA8
128K x 8 AutoStoreTM nvSRAM
QuantumTrapTM CMOS
Nonvolatile Static RAM
FEATURES
DESCRIPTION
• 25ns, 35ns and 45ns Access Times
The Simtek STK14CA8 is a fast static RAM with a
nonvolatile element in each memory cell. The
embedded nonvolatile elements incorporate
• “Hands-off” Automatic STORE on Power Down
with only a small capacitor
Simtek’s QuantumTrapTM technology producing the
world’s most reliable nonvolatile memory. The
SRAM provides unlimited read and write cycles,
while independent, nonvolatile data resides in the
highly reliable QuantumTrapTM cell. Data transfers
from the SRAM to the nonvolatile elements (the
STORE operation) takes place automatically at
power down. On power up, data is restored to the
SRAM (the RECALL operation) from the nonvolatile
memory. Both the STORE and RECALL operations
are also available under software control.
• STORE to QuantumTrap™ Nonvolatile
Elements is Initiated by Software , device pin
or AutoStore™ on Power Down
• RECALL to SRAM Initiated by Software or
Power Up
• Unlimited READ, WRITE and RECALL Cycles
• 10mA Typical ICC at 200ns Cycle Time
• High-reliability
o Endurance to 500K STORE Cycles
o Data Retention to 20 Years
• Single 3V +20%, -10% Operation
• Commercial and Industrial Temperatures
• SOIC, and SSOP Packages (RoHs Compliance)
BLOCK DIAGRAM
VCC
VCAP
Quantum Trap
1024 X 1024
A5
POWER
A6
A7
A8
A9
A12
A13
A14
A15
A16
CONTROL
STORE
RECALL
STORE/
RECALL
CONTROL
STATIC RAM
ARRAY
1024 X 1024
HSB
SOFTWARE
DETECT
A15 – A0
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
COLUMN I/O
COLUMN DEC
A0 A1 A2 A3 A4 A10 A11
G
E
W
Figure 1. Block Diagram
December 2005
1
Document Control #ML0022 rev 1.3
STK14CA8
PACKAGES
VCAP
A16
A14
1
2
3
4
5
6
VCC
A15
HSB
48
47
VCAP
A16
A14
1
2
3
4
5
6
VCC
A15
32
31
46
45
44
43
HSB
W
A13
A8
30
29
28
27
A12
A7
A6
W
A13
A8
A12
A7
A6
A5
7
8
9
10
11
12
13
14
15
16
A9
42
41
40
39
38
37
36
35
34
33
A5
A4
A3
A2
A1
A9
7
8
9
10
11
12
13
14
15
16
26
25
24
23
22
21
20
19
18
17
A11
G
A10
E
DQ7
A4
A11
A0
VSS
VSS
DQ0
DQ1
DQ2
VSS
DQ6
DQ5
DQ4
DQ3
DQ0
A3
A2
A1
A0
DQ6
G
A10
E
DQ7
17
18
32
31
30
29
28
27
26
25
32 Pin SOIC
19
20
21
22
23
24
DQ1
DQ2
DQ5
DQ4
DQ3
VCC
48 Pin SSOP
Relative PCB area usage.
See website for detailed
package size specifications.
PIN DESCRIPTIONS
Pin Name
I/O
Description
A16 – A0
Input
Address: The 17 address inputs select one of 131,072 bytes in the nvSRAM array.
Data: Bi-directional 8-bit data bus for accessing the nvSRAM.
DQ7 –DQ0
E
I/O
Input
Chip Enable: The active low
Write Enable: The active low
E
input selects the device.
W
enables data on the DQ pins to be written to the address location latched by
W
Input
the falling edge of E
.
Output Enable: The active low
G
input enables the data output buffers during read cycles. De-asserting G
G
Input
high causes the DQ pins to tri-state.
Power 3.0V +20%, -10%
VCC
Power Supply
Hardware Store Busy: When low this output indicates a Hardware Store is in progress. When pulled low external
HSB
I/O
to the chip it will initiate a nonvolatile STORE operation. A weak internal pull up resistor keeps this pin high if not
connected. (Connection Optional)
Autostore Capacitor: Supplies power to nvSRAM during power loss to store data from SRAM to nonvolatile
VCAP
Power Supply
elements.
VSS
Power Supply
No Connect
Ground
(Blank)
Unlabeled pins have no internal connection.
December 2005
2
Document Control #ML0022 rev 1.3
STK14CA8
ABSOLUTE MAXIMUM RATINGSa
Notes
-0.5V to +4.1V
Power Supply Voltage
Voltage on Input Relative to VSS
Voltage on Outputs
a: Stresses greater than those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device. This is a
stress rating only, and functional operation of the device at con-
ditions above those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rat-
ing conditions for extended periods may affect reliability.
-0.5V to (VCC + 0.5V)
-0.5V to (VCC + 0.5V)
–55°C to 125°C
–55°C to 140°C
–65°C to 150°C
1W
Temperature under Bias
Junction Temperature
Storage Temperature
Power Dissipation
DC Output Current (1 output at a time, 1s duration)
15mA
Package Thermal Characteristics see website: http://www.simtek.com/
DC CHARACTERISTICS
Commercial
Industrial
Symbol
Parameter
Units
mA
mA
mA
Notes
MIN
MAX
65
55
50
MIN
MAX
70
60
55
tAVAV = 25ns
tAVAV = 35ns
tAVAV = 45ns
Average VCC Current
ICC1
Dependent on output loading and cycle
rate. Values obtained without output loads.
All Inputs Don’t Care, VCC = max
Average current for duration of STORE
cycle (tSTORE).
Average VCC Current during STORE
Average VCC Current at tAVAV = 200ns
3V, 25°C, Typical
ICC2
ICC3
ICC4
ISB
3
3
mA
W
≥ (VCC – 0.2V)
All Others Inputs Cycling, at CMOS Levels.
Dependent on output loading and cycle
rate. Values obtained without output loads.
All Inputs Don’t Care
Average current for duration of STORE
cycle (tSTORE).
10
3
10
3
mA
mA
Average VCAP Current during
AutoStore™ Cycle
VCC Standby Current
E
≥ (VCC – 0.2V)
All Others VIN ≤ 0.2V or ≥ (VCC – 0.2V)
Standby current level after nonvolatile
cycle is complete.
(Standby, Stable CMOS Input Levels)
3
3
mA
µA
VCC = max
Input Leakage Current
IILK
±1
±1
±1
VIN = VSS to VCC
VCC = max
Off-State Output Leakage Current
IOLK
VIN = VSS to VCC, E or G ≥ VIH
±1
VCC + 0.3
0.8
µA
V
Input Logic “1” Voltage
Input Logic “0” Voltage
Output Logic “1” Voltage
Output Logic “0” Voltage
Operating Temperature
Operating Voltage
VIH
VIL
2.0
V
CC + 0.3
0.8
2.0
VSS – 0.5
2.4
All Inputs
All Inputs
V
SS – 0.5
2.4
V
VOH
V
IOUT = –2mA
VOL
0.4
70
0.4
85
V
IOUT = 4mA
TA
0
–40
2.7
17
oC
VCC
2.7
17
3.6
57
3.6
57
V
3.0V +20%, -10%
Storage Capacitor
VCAP
NVC
DATAR
µF
K
Between Vcap pin and Vss, 5V rated.
Nonvolatile STORE operations
Data Retention
500
20
500
20
500
Years
@ Maximum Operating Temperature
December 2005
3
Document Control #ML0022 rev 1.3
STK14CA8
AC TEST CONDITIONS
0V to 3V
Input Pulse Levels
Input Rise and Fall Times
Input and Output Timing Reference Levels
≤ 5ns
1.5V
Output Load
See Figure 2 and Figure 3
CAPACITANCEb
(TA = 25°C, f = 1.0MHz)
SYMBOL
PARAMETER
MAX
UNITS
pF
CONDITIONS
∆V = 0 to 3V
∆V = 0 to 3V
CIN
Input Capacitance
Output Capacitance
7
7
COUT
pF
Notes
b: These parameters are guaranteed but not tested
3.0V
3.0V
577 Ohms
577 Ohms
OUTPUT
OUTPUT
5 pF
30 pF
INCLUDING
SCOPE AND
FIXTURE
789 Ohms
789 Ohms
INCLUDING
SCOPE AND
FIXTURE
Figure 2. AC Output Loading
Figure 3. AC Output Loading,
for tristate specs (
tHZ, tLZ, tWLQZ, tWHQZ
tGLQX, tGHQZ
,
)
December 2005
4
Document Control #ML0022 rev 1.3
STK14CA8
SRAM READ CYCLES #1 & #2
SYMBOLS
STK14CA8-25
STK14CA8-35
STK14CA8-45
NO.
PARAMETER
UNITS
#1
#2
Alt.
tACS
MIN
MAX
MIN
MAX
MIN
MAX
tELQV
1
2
Chip Enable Access Time
Read Cycle Time
25
35
45
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
c
c
tAVAV
tAVAV
tRC
tAA
tOE
tOH
tLZ
25
35
45
d
tAVQV
3
Address Access Time
25
12
35
15
45
20
tGLQV
4
Output Enable to Data Valid
Output Hold after Address Change
Chip Enable to Output Active
Chip Disable to Output Inactive
Output Enable to Output Active
Output Disable to Output Inactive
Chip Enable to Power Active
Chip Disable to Power Standby
d
tAXQX
5
3
3
3
3
3
3
tELQX
tEHQZ
tGLQX
6
e
tHZ
tOLZ
tOHZ
tPA
tPS
7
10
10
25
13
13
35
15
15
45
8
0
0
0
0
0
0
e
tGHQZ
9
b
tELICC
10
b
tEHICC
11
Notes
c:
W
must be high during SRAM READ cycles
and
d: Device is continuously selected with
E
G
both low
e: Measured ± 200mV from steady state output voltage
f: HSB must remain high during READ and WRITE cycles.
SRAM READ CYCLE #1: Address Controlledc,d,f
2
tAVAV
ADDRESS
3
tAVQV
5
tAXQX
DATA VALID
DQ (DATA OUT)
SRAM READ CYCLE #2: E Controlledc,f
2
tAVAV
ADDRESS
1
tELQV
11
tEHICCL
6
tELQX
E
7
tEHQZ
G
9
tGHQZ
4
tGLQV
8
tGLQX
DQ (DATA OUT)
DATA VALID
10
tELICCH
ACTIVE
STANDBY
ICC
December 2005
5
Document Control #ML0022 rev 1.3
STK14CA8
SRAM WRITE CYCLES #1 & #2
SYMBOLS
NO.
STK14CA8-25
STK14CA8-35
STK14CA8-45 UNITS
PARAMETER
#1
#2
Alt.
tWC
tWP
tCW
tDW
tDH
MIN
25
20
20
10
0
MAX
MIN
35
25
25
12
0
MAX
MIN
45
30
30
15
0
MAX
Write Cycle Time
12
13
14
15
16
17
18
19
20
21
tAVAV
tWLWH
tELWH
tDVWH
tWHDX
tAVWH
tAVWL
tWHAX
tAVAV
tWLEH
tELEH
tDVEH
tEHDX
tAVEH
tAVEL
tEHAX
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Write Pulse Width
Chip Enable to End of Write
Data Set-up to End of Write
Data Hold after End of Write
Address Set-up to End of Write
Address Set-up to Start of Write
Address Hold after End of Write
Write Enable to Output Disable
Output Active after End of Write
tAW
tAS
20
0
25
0
30
0
tWR
tWZ
tOW
0
0
0
e,g
tWLQZ
10
13
15
tWHQX
3
3
3
Notes
g: If
h:
W
is low when E goes low, the outputs remain in the high-impedance state.
E
or
W
must be ≥ VIH during address transitions.
SRAM WRITE CYCLE #1: W Controlledh,f
12
tAVAV
ADDRESS
19
tWHAX
14
tELWH
E
17
tAVWH
18
13
tWLWH
tAVWL
W
15
16
tDVWH
tWHDX
DATA VALID
DATA IN
20
tWLQZ
21
tWHQX
HIGH IMPEDANCE
PREVIOUS DATA
DATA OUT
SRAM WRITE CYCLE #2: E Controlledh,f
12
tAVAV
ADDRESS
18
14
tELEH
19
tEHAX
tAVEL
E
17
tAVEH
13
tWLEH
W
16
tEHDX
15
tDVEH
DATA VALID
DATA IN
HIGH IMPEDANCE
DATA OUT
December 2005
6
Document Control #ML0022 rev 1.3
STK14CA8
AutoStore™ /POWER-UP RECALL
SYMBOLS
NO.
PARAMETER
STK14CA8
UNITS
NOTES
Standard
Alternate
MIN
MAX
22
23
24
25
tHRECALL
20
ms
ms
V
i
Power-up RECALL Duration
tSTORE
tHLHZ
12.5
2.65
j,k
STORE Cycle Duration
VSWITCH
tVCCRISE
2.55
150
Low Voltage Trigger Level
µs
V
CC Rise Time
Notes
i: tHRECALL starts from the time VCC rises above VSWITCH
j: If an SRAM WRITE has not taken place since the last nonvolatile cycle, no STORE will take place
k: Industrial Grade Devices require 15ms MAX.
STORE occurs only if a
SRAM write has
happened.
No STORE occurs
without at least one
SRAM write.
AutoStore™/POWER-UP RECALL
VCC
24
VSWITCH
25
tVCCRISE
AutoStoreTM
23
tSTORE
23
tSTORE
POWER-UP RECALL
22
tHRECALL
22
tHRECALL
Read & Write Inhibited
POWER DOWN
BROWN OUT
POWER-UP
RECALL
POWER-UP
RECALL
AutoStoreTM
AutoStoreTM
Note: Read and Write cycles will be ignored during STORE, RECALL and while VCC is below VSWITCH
December 2005
7
Document Control #ML0022 rev 1.3
STK14CA8
SOFTWARE-CONTROLLED STORE/RECALL CYCLEl,m
SYMBOLS
STK14CA8-25
STK14CA8-35
STK14CA8-45
NO.
PARAMETER
UNITS
NOTES
m
E
G
Alt.
tRC
MIN
MAX
MIN
MAX
MIN
MAX
cont
cont
26
27
tAVAV
tAVAV
25
0
35
0
45
0
ns
ns
ns
ns
µs
STORE/RECALL Initiation Cycle Time
Address Set-up Time
Clock Pulse Width
tAVEL
tAVGL
tAS
28
tELEH
tELAX
tGLGH
tGLAX
tCW
20
20
25
20
30
20
29
Address Hold Time
30
tRECALL
tRECALL
50
50
50
RECALL Duration
Notes
l: The software sequence is clocked with
E
controlled READs or G controlled READs.
m: The six consecutive addresses must be read in the order listed in the Mode Selection Table.
W
must be high during all six consecutive cycles.
SOFTWARE STORE/RECALL CYCLE: E Controlledm
26
tAVAV
26
tAVAV
ADDRESS #1
ADDRESS #6
ADDRESS
E
27
tAVEL
28
tELEH
29
tELAX
G
23
30
/
tSTORE tRECALL
HIGH IMPEDENCE
DATA VALID
DQ (DATA)
DATA VALID
SOFTWARE STORE/RECALL CYCLE: G Controlledm
26
26
tAVAV
tAVAV
ADDRESS #1
ADDRESS #6
ADDRESS
E
28
tGLGH
27
tAVGL
G
30
tRECALL
23
tSTORE
/
29
tGLAX
HIGH IMPEDENCE
DATA VALID
DATA VALID
DQ (DATA)
December 2005
8
Document Control #ML0022 rev 1.3
STK14CA8
HARDWARE STORE CYCLE
SYMBOLS
NO.
STK14CA8
PARAMETER
UNITS
NOTES
n
Standard
tDELAY
tHLHX
tHLBL
Alternate
MIN
MAX
tHLQZ
31
32
33
Time Allowed to Complete SRAM Cycle
Hardware STORE Pulse Width
1
µs
ns
ns
15
Hardware STORE Low to STORE Busy
300
Notes
n: Read and Write cycles in progress before HSB is asserted are given this amount of time to complete.
HARDWARE STORE CYCLE
32
tHLHX
HSB (IN)
23
tSTORE
33
tHLBL
HSB (OUT)
HIGH IMPEDENCE
HIGH IMPEDENCE
31
tDELAY
DQ (DATA OUT)
DATA VALID
DATA VALID
Soft Sequence Commands
SYMBOLS
STK14CA8
NO.
PARAMETER
UNITS
NOTES
Standard
MIN
MAX
tSS
34
Notes
Soft Sequence Processing Time
70
µs
o,p
o: This is the amount of time that it takes to take action on a soft sequence command. Vcc power must remain high to effectively register command.
p: Commands like Store and Recall lock out I/O until operation is complete which further increases this time. See specific command.
34
tSS
34
tSS
Soft Sequence Command
ADDRESS #1
Soft Sequence Command
ADDRESS #1
ADDRESS #6
ADDRESS #6
ADDRESS
Vcc
December 2005
Document Control #ML0022 rev 1.3
9
STK14CA8
MODE SELECTION
E
W
G
A15 - A0
MODE
I/O
POWER
NOTES
H
L
L
X
H
L
X
L
X
X
X
Not Selected
Read SRAM
Write SRAM
Output High Z
Output Data
Input Data
Standby
Active
X
Active
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x8B45
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Output Data
Output Data
Output Data
Output Data
Output Data
Output Data
L
L
H
H
L
L
Active
Active
q, r, s
Autostore Disable
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x4B46
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Autostore Enable
Output Data
Output Data
Output Data
Output Data
Output Data
Output Data
q, r, s
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x8FC0
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Nonvolatile Store
Output Data
Output Data
Output Data
Output Data
Output Data
Output High Z
Active
ICC2
L
L
H
H
L
L
q, r, s
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x4C63
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Output Data
Output Data
Output Data
Output Data
Output Data
Output High Z
Active
q, r, s
Nonvolatile Recall
Notes
q: The six consecutive addresses must be in the order listed.
r: While there are 17 addresses on the STK14CA8, only the lower 16 are used to control software modes
s: I/O state depends on the state of . The I/O table shown assumes low.
W
must be high during all six consecutive cycles to enable a nonvolatile cycle.
G
G
December 2005
10
Document Control #ML0022 rev 1.3
STK14CA8
DEVICE OPERATION
SRAM WRITE
nvSRAM
A WRITE cycle is performed whenever E and W are
low and HSB is high. The address inputs must be
stable prior to entering the WRITE cycle and must
remain stable until either E or W goes high at the
end of the cycle. The data on the common I/O pins
DQ0-7 will be written into the memory if it is valid tDVWH
before the end of a W controlled WRITE or tDVEH
before the end of an E controlled WRITE.
The STK14CA8 nvSRAM is made up of two
functional components paired in the same physical
cell. These are a SRAM memory cell and a
nonvolatile QuantumTrap™ cell. The SRAM
memory cell operates as a standard fast static
RAM. Data in the SRAM can be transferred to the
nonvolatile cell (the STORE operation), or from
the nonvolatile cell
to SRAM (the RECALL
operation). This unique architecture allows all cells
to be stored and recalled in parallel. During the
STORE and RECALL operations SRAM READ and
WRITE operations are inhibited. The STK14CA8
supports unlimited reads and writes just like a
typical SRAM. In addition, it provides unlimited
RECALL operations from the nonvolatile cells and
up to 500K STORE operations.
It is recommended that G be kept high during the
entire WRITE cycle to avoid data bus contention on
common I/O lines. If G is left low, internal circuitry will
turn off the output buffers tWLQZ after W goes low.
AutoStore™ OPERATION
The STK14CA8 stores data to nvSRAM using one of
three storage operations. These three operations are
Hardware Store, activated by HSB , Software Store,
actived by an address sequence, and AutoStore™, on
device power down.
SRAM READ
The STK14CA8 performs a READ cycle whenever
E and G are low while W and HSB are high.
The address specified on pins A16-0 determines
which of the 131,072 data bytes will be accessed.
When the READ is initiated by an address
transition, the outputs will be valid after a delay of
tAVQV (READ cycle #1). If the READ is initiated by
E or G , the outputs will be valid at tELQV or at
tGLQV, whichever is later (READ cycle #2). The data
outputs will repeatedly respond to address
changes within the tAVQV access time without the
need for transitions on any control input pins, and
will remain valid until another address change or
AutoStore™ operation is a unique feature of Simtek
QuantumTrap™ technology and is enabled by default
on the STK14CA8.
During normal operation, the device will draw current
from Vcc to charge a capacitor connected to the Vcap
pin. This stored charge will be used by the chip to
perform a single STORE operation. If the voltage on
the Vcc pin drops below Vswitch, the part will
automatically disconnect the Vcap pin from Vcc.
A
STORE operation will be initiated with power provided
by the Vcap capacitor.
until E or G is brought high, or
brought low.
W
or HSB is
Figure 4 shows the proper connection of the storage
capacitor (Vcap) for automatic store operation. Refer to
the DC CHARACTERISTICS table for the size of Vcap.
The voltage on the Vcap pin is driven to 5V by a
charge pump internal to the chip. A pull up should be
placed on W to hold it inactive during power up.
VCC
VCAP
VCC
To reduce unneeded nonvolatile stores, AutoStore™
and Hardware Store operations will be ignored unless
at least one WRITE operation has taken place since
the most recent STORE or RECALL cycle. Software
initiated STORE cycles are performed regardless of
whether a WRITE operation has taken place. The
HSB signal can be monitored by the system to detect
an AutoStore™ cycle is in progress.
W
Figure 4: AutoStoreTM Mode
December 2005
11
Document Control #ML0022 rev 1.3
STK14CA8
SOFTWARE STORE
HARDWARE STORE ( HSB )
Data can be transferred from the SRAM to the
nonvolatile memory by a software address sequence.
The STK14CA8 software STORE cycle is initiated by
executing sequential E controlled READ cycles from
six specific address locations in exact order. During
the STORE cycle an erase of the previous nonvolatile
data is first performed, followed by a program of the
nonvolatile elements. Once a STORE cycle is
initiated, further input and output are disabled until the
cycle is completed.
OPERATION
The STK14CA8 provides the HSB pin for controlling
and acknowledging the STORE operations. The
HSB pin can be used to request a hardware STORE
cycle. When the HSB pin is driven low, the
STK14CA8 will conditionally initiate a STORE
operation after tDELAY. An actual STORE cycle will
only begin if a WRITE to the SRAM took place since
the last STORE or RECALL cycle. The HSB pin also
acts as an open drain driver that is internally driven
low to indicate a busy condition while the STORE
(initiated by any means) is in progress.
Because a sequence of READs from specific
addresses is used for STORE initiation, it is important
that no other READ or WRITE accesses intervene in
the sequence, or the sequence will be aborted and no
STORE or RECALL will take place.
SRAM READ and WRITE operations that are in
progress when HSB is driven low by any means are
given time to complete before the STORE operation
is initiated. After HSB goes low, the STK14CA8 will
To initiate the software STORE cycle, the following
READ sequence must be performed:
continue SRAM operations for tDELAY. During tDELAY
,
1. Read address
2. Read address
3. Read address
4. Read address
5. Read address
6. Read address
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x8FC0
Valid READ
Valid READ
Valid READ
Valid READ
Valid READ
Initiate STORE cycle
multiple SRAM READ operations may take place. If a
WRITE is in progress when HSB is pulled low it will
be allowed a time, tDELAY, to complete. However, any
SRAM WRITE cycles requested after HSB goes low
will be inhibited until HSB returns high.
The software sequence may be clocked with
controlled READs or G controlled READs.
E
During any STORE operation, regardless of how it
was initiated, the STK14CA8 will continue to drive
the HSB pin low, releasing it only when the STORE
is complete. Upon completion of the STORE
operation the STK14CA8 will remain disabled until
the HSB pin returns high.
Once the sixth address in the sequence has been
entered, the STORE cycle will commence and the
chip will be disabled. It is important that READ cycles
and not WRITE cycles be used in the sequence,
although it is not necessary that G be low for the
sequence to be valid. After the tSTORE cycle time has
been fulfilled, the SRAM will again be activated for
READ and WRITE operation.
If HSB is not used, it should be left unconnected.
HARDWARE RECALL (POWER-UP)
During power up, or after any low-power condition
(VCC < VSWITCH), an internal RECALL request will be
latched. When VCC once again exceeds the sense
voltage of VSWITCH, a RECALL cycle will automatically
be initiated and will take tHRECALL to complete.
SOFTWARE RECALL
Data can be transferred from the nonvolatile memory
to the SRAM by a software address sequence. A
software RECALL cycle is initiated with a sequence of
READ operations in a manner similar to the software
STORE initiation. To initiate the RECALL cycle, the
following sequence of E controlled READ operations
must be performed:
1. Read address
2. Read address
3. Read address
4. Read address
5. Read address
6. Read address
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x4C63
Valid READ
Valid READ
Valid READ
Valid READ
Valid READ
Initiate RECALL cycle
December 2005
12
Document Control #ML0022 rev 1.3
STK14CA8
Internally, RECALL is a two-step procedure. First,
the SRAM data is cleared, and second, the
nonvolatile information is transferred into the SRAM
cells. After the tRECALL cycle time the SRAM will
once again be ready for READ and WRITE
operations. The RECALL operation in no way alters
the data in the nonvolatile elements.
NOISE CONSIDERATIONS
The STK14CA8 is a high-speed memory and so must
have high-frequency bypass capacitor of
a
approximately 0.1µF connected between VCC and VSS,
using leads and traces that are as short as possible. As
with all high-speed CMOS ICs, careful routing of power,
ground and signals will reduce circuit noise.
DATA PROTECTION
LOW AVERAGE ACTIVE POWER
The STK14CA8 protects data from corruption
during low-voltage conditions by inhibiting all
externally initiated STORE and WRITE operations.
The low-voltage condition is detected when VCC
VSWITCH .
CMOS technology provides the STK14CA8 this the
benefit of drawing significantly less current when it is
cycled at times longer than 50ns. Figure 5 shows the
relationship between ICC and READ/WRITE cycle time.
Worst-case current consumption is shown for
commercial temperature range, VCC = 3.6V, and chip
enable at maximum frequency. Only standby current is
drawn when the chip is disabled. The overall average
current drawn by the STK14CA8 depends on the
following items:
<
If the STK14CA8 is in a WRITE mode (both E and
W low ) at power-up, after a RECALL, or after a
STORE, the WRITE will be inhibited until a
negative transition on E or
protects against inadvertent writes during power up
or brown out conditions.
W
is detected. This
1. The duty cycle of chip enable.
2. The overall cycle rate for accesses.
3. The ratio of READs to WRITEs.
4. The operating temperature.
5. The VCC level.
6. I/O loading.
50
40
30
Writes
20
10
Reads
0
50 100 150 200 300
Cycle Time (ns)
Figure 5 Current vs. Cycle time
December 2005
13
Document Control #ML0022 rev 1.3
STK14CA8
PREVENTING AUTOSTORETM
sequence of read operations is performed in a
manner similar to the software RECALL initiation. To
initiate the AutoStore Enable sequence, the following
The AutoStore™ function can be disabled by
initiating an AutoStore Disable sequence. A
sequence of read operations is performed in a
manner similar to the software STORE initiation.
To initiate the AutoStore Disable sequence, the
sequence of
performed:
E
controlled read operations must be
1. Read address
2. Read address
3. Read address
4. Read address
5. Read address
6. Read address
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x4B46
Valid READ
Valid READ
Valid READ
Valid READ
Valid READ
AutoStore Enable
following sequence of
E
controlled read
operations must be performed:
1. Read address
2. Read address
3. Read address
4. Read address
5. Read address
6. Read address
0x4E38
0xB1C7
0x83E0
0x7C1F
0x703F
0x8B45
Valid READ
Valid READ
Valid READ
Valid READ
Valid READ
AutoStore Disable
If the AutoStore™ function is disabled or re-enabled a
manual STORE operation (Hardware or Software)
needs to be issued to save the AutoStore state
through subsequent power down cycles. The part
comes from the factory with AutoStore™ enabled.
The AutoStore™ can be re-enabled by
initiating an AutoStore Enable sequence. A
December 2005
14
Document Control #ML0022 rev 1.3
STK14CA8
EXTENDED TEMPURATURE RANGE
The STK14CA8 is offered in an extended
temperature range part number. This part number
is tested from -55ºC to +85ºC. This range is
extended from the standard industrial range device
on the maximum cold temperature specification.
All of the industrial specifications in this datasheet
apply to the extended temperature range device
except for the maximum number of STORE
(Endurance) cycles . The maximum number of
STORE cycles for the extended temperature range
device is 100K cycles.
December 2005
15
Document Control #ML0022 rev 1.3
STK14CA8
ORDERING INFORMATION
STK14CA8 – R F 45 I
Temperature Range
Blank = Commercial (0 to 70ºC)
I = Industrial (-40 to 85ºC)
G = Extended (-55 to 85ºC)
Access Time
25 = 25ns
35 = 35ns
45 = 45ns
Lead Finish
Blank = 85% Sn / 15% Pb
F = 100% Sn (Matte Tin) RoHS Compliant
Package
N = Plastic 32-pin 300 mil SOIC (50 mil pitch)
R = Plastic 48-pin 300 mil SSOP (25 mil pitch)
December 2005
16
Document Control #ML0022 rev 1.3
STK14CA8
Document Revision History
Summary
Revision
Date
Publish new datasheet
0.0
January 2003
Add 48 pin SSOP, Modify AutoStore drawing (Figure 2), Update Mode Selection
0.1
0.2
May 2003
Table and Absolute Maximum Ratings, Added
Added lead-free lead finish
G control software store.
September 2003
Parameter
Vcap Min
Old Value
10µF
New Value
17 µF
Notes
tVCCRISE
NA
150 µs
50 mA
55 mA
65 mA
55 mA
60 mA
70 mA
3.0 mA
3 mA
New Spec
ICC1 Max Com.
ICC1 Max Com.
ICC1 Max Com.
ICC1 Max Ind.
ICC1 Max Ind.
ICC1 Max Ind.
ICC2 Max
35 mA
40 mA
50 mA
35 mA
45 mA
55 mA
1.5 mA
0.5 mA
5 ms
@ 45ns access
@ 35ns access
@ 25ns access
@ 45ns access
@ 35ns access
@ 25ns access
Com. & Ind.
1.0
December 2004
ICC4 Max
tHRECALL
tSTORE
tRECALL
Com & Ind.
20 ms
12.5 ms
40µs
10 ms
20µs
tGLQV
10ns
12ns
25 ns device
Parameter
ICC3 Max Com.
ICC3 Max Ind.
ISB Max Com.
ISB Max Ind.
tRECALL
Old Value
5 mA
New Value
10 mA
10 mA
3 mA
Notes
5 mA
2 mA
2 mA
40 µs
3 mA
50 µs
1.1
August 2005
Soft Recall
Industrial Grade
Only
Contact Simtek for
details.
tSTORE
12.5 ms
1x106
15 ms
5x105
Max. STORE
Cycles
Removed Plastic Dip 32 pin package offering. Package type “W”.
Added an Extended Temperature Range device tested from -55ºC to +85ºC.
1.2
1.3
September 2005
December 2005
Parameter
tRECALL
Old Value
New Value
50 µs
Notes
Typographical
Error in Datasheet
60 µs
tSS
Undefined
100 Years at
Unspecified
Temperature
70 µs
20 Years @ Max
Temperature
Data Retention
New Specification
DATAR
SIMTEK STK14CA8 Data Sheet, December 2005
Copyright 2005, Simtek Corporation. All rights reserved.
This datasheet may only be printed for the express use of Simtek Customers. No part of this datasheet may be reproduced in any other form or
means without express written permission from Simtek Corporation. The information contained in this publication is believed to be accurate, but
changes may be made without notice. Simtek does not assume responsibility for, or grant or imply any warranty, including MERCHANTABILITY
or FITNESS FOR A PARTICULAR PURPOSE regarding this information, the product or its use. Nothing herein constitutes a license, grant or
transfer of any rights to any Simtek patent, copyright, trademark or other proprietary right.
December 2005
17
Document Control #ML0022 rev 1.3
相关型号:
©2020 ICPDF网 联系我们和版权申明