PCA-9410 [DEI]
Pulsed Voltage Source;型号: | PCA-9410 |
厂家: | Directed Energy |
描述: | Pulsed Voltage Source |
文件: | 总3页 (文件大小:731K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PVX-4000-2kV-EX Pulsed Voltage Source Datasheet
Precision Pulse Control
The PVX-4000-2kV-EX is an air-cooled, high voltage pulse
generator. Optimized for high impedance capacitive loads,
the PVX-4000-2kV-EX is well-suited for driving extraction
grids and deflection plates for electrostatic modulation of
particle beams in time-of-flight mass spectrometers and
accelerators.
+1000 V & -1000 V, 4 kHz, 100.0 µs, 344 pF Load
System Operation
The PVX-4000-2kV-EX system requires external high
voltage power supplies. Using external HVPSs, the output
voltage can be set from 0 V to ±2000 V. Duty cycles from
2% to 98% and repetition rates from 40 Hz to 30,000 Hz
are supported by the internal trigger source.
If using the internal trigger source, when changing the
frequency, the duty cycle is maintained and the new pulse
width is displayed. It is recommended that the frequency
be changed before the pulse width is changed.
Pulse widths from 500 ns to 100% duty cycle and repetition
rates from single-shot to 600 kHz are supported when an
external trigger source is used.
Computer Interfaces
+750 V & -750 V, 4 kHz, 100.0 µs, 344 pF Load
For automated applications, complete control of the
instrument is provided through RS-232 and USB computer
interfaces. Up to five system configurations may be stored
in internal non-volatile memory, providing instant recall of
frequently-used configurations.
Control Signals
Conveniently-located front panel BNC connectors allow
the PVX-4000-2kV-EX to be externally triggered. The
impedance of the gate input is 50 Ω.
The system has a Sync output for interconnection to other
equipment. The pulse from the Sync output is
synchronized to the leading edge of the output voltage
pulse. The impedance of the sync output is 50 Ω.
The system can easily be monitored through the Voltage
Monitor BNC connection using an oscilloscope set to 1 MΩ
termination.
+50 V & -50 V, 4 kHz, 100.0 µs, 344 pF Load
Ordering Information
PVX-4000-2kV-EX
PCA-9400
PCA-9410
System
3x Input/Output Cables
1x BNC Shorting Connector
For more information contact IXYS Colorado: 970.493.1901 or sales@ixyscolorado.com
Document #7675-0022 Rev A01. © Copyright 2017 IXYS Colorado. All rights reserved.
PVX-4000-2kV-EX Pulsed Voltage Source Datasheet
Pulse Characteristics
High Voltage Connectors
Output Voltage Range
Voltage Overshoot
0 V to ±2000 V ***
Pulsed Output Connector
DC HV Input Connectors
Winchester Kings 10 kV, Rear Panel
< 2%
1065-2 plug
Winchester Kings 10 kV, Rear Panel
1065-2 plug
Voltage Rise/Fall Time
≤ 50 ns from 500 V to 2000 V
≤ 100 ns from 200 V to 500 V
≤ 50 ns from -500 V to -2000 V
≤ 100 ns from -200 V to -500 V
Voltage Rise/Fall Time
Output Power
Power Specifications
Voltage Requirements
100 VAC to 120 VAC ± 10%
Refer to SOA Graphs
220 VAC to 240 VAC ± 10%
50 Hz to 60 Hz
100 W
Line Frequency
Power Requirements
AC Connector Type
*** The positive and negative high voltage input levels must not
exceed 2000 V total. Reduce the high voltage input on either
channel to achieve ≤ 2000 V. Use the below formula:
NEMA C-14
Vpositive + |Vnegative| ≤ 2000 V
General
Size (HxWxD)
15 cm x 49 cm x 52 cm
7 kg
15 °C to 35 °C
RS-232 and USB, @ 115200
baud, 8 data bits, no parity, 1
stop bit, and no flow control
Internal Trigger
Weight
Operating Temperature
Computer Comunication
Frequency Range
40 Hz to 30000 Hz
40 Hz to 1000 Hz @ 10 Hz
1100 Hz to 30000 Hz @ 100 Hz
Frequency Resolution
Pulse Width
2% to 98% Duty Cycle
Pulse Width Resolution
6.4 µs from 40 Hz to 1000 Hz
0.4 µs from 1100 Hz to 5000 Hz
0.05 µs from 5100 Hz to 30000 Hz
Notes
Warranty: One year parts and labor on defects in materials
and workmanship.
External Gate
Frequency Range
Trigger Pulse Width
Termination Impedance
Connector
1. The PVX-4000-2kV-EX voltage source meets or exceeds
these specifications. The system was tested driving a
344 pF load at 2000 V output.
2. The factory supplied output cable has 1.57 pF / 1.0 cm of
cable. This needs to be calculated in the load value.
3. VMON is designed to be used with RG 58/U 2ft long coax
cable connected between the VMON BNC output and an
oscilloscope terminated in to a 1 M ohm input
impedance.
Single-shot to 600 kHz
500 ns to 100% duty cycle
50 Ω
BNC
Input Voltage Levels
0 V input = output pulse off
+5 V input = output pulse on
Monitors
Voltage Monitor
1000 V / 10 V (typical), see note 3.
Specifications subject to change without notice.
Voltage Monitor Termination 1 Mꢀ
Voltage Monitor Connector
BNC
Sync Termination
Sync Connector
50 ꢀ
BNC
Output Voltage Levels
0 V output = - HV output pulse
< +3.3 V output = + HV output pulse
Enable Input BNC connector External dry-contact closure or factory
supplied shorting BNC plug.
For more information contact IXYS Colorado: 970.493.1901 or sales@ixyscolorado.com
Document #7675-0022 Rev A01. © Copyright 2017 IXYS Colorado. All rights reserved.
PVX-4000-2kV-EX Pulsed Voltage Source Datasheet
Safe operating area graph; stay below the line for proper operation.
For more information contact IXYS Colorado: 970.493.1901 or sales@ixyscolorado.com
Document #7675-0022 Rev A01. © Copyright 2017 IXYS Colorado. All rights reserved.
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明