AT25XE021A_技术文档

AT25XE021A

2-Mbit, 1.65V Minimum

SPI Serial Flash Memory with Dual-I/O Support

Features



Single 1.65V - 3.6V Supply

Serial Peripheral Interface (SPI) Compatible

 Supports SPI Modes 0 and 3

 Supports Dual-I/O Operation



70MHz Maximum Operating Frequency

 Clock-to-Output (t_V) of 6 ns

Flexible, Optimized Erase Architecture for Code + Data Storage Applications

 Small (256-Byte) Page Erase

 Uniform 4-Kbyte Block Erase

 Uniform 32-Kbyte Block Erase

 Uniform 64-Kbyte Block Erase

 Full Chip Erase



Hardware Controlled Locking of Protected Sectors via WP Pin

128-byte, One-Time Programmable (OTP) Security Register

 64 bytes factory programmed with a unique identifier

 64 bytes user programmable



Flexible Programming

 Byte/Page Program (1 to 256 Bytes)

 Dual-Input Byte/Page Program (1 to 256 Bytes)

 Sequential Program Mode Capability

Fast Program and Erase Times

 2ms Typical Page Program (256 Bytes) Time

 45ms Typical 4-Kbyte Block Erase Time

 360ms Typical 32-Kbyte Block Erase Time

 720ms Typical 64-Kbyte Block Erase Time



Automatic Checking and Reporting of Erase/Program Failures

Software Controlled Reset

JEDEC Standard Manufacturer and Device ID Read Methodology

Low Power Dissipation

 200nA Ultra Deep Power Down current (Typical)

 4.5µA Deep Power-Down Current (Typical)

 25uA Standby current (Typical)

 3mA Active Read Current (Typical)



Endurance: 100,000 Program/Erase Cycles

Data Retention: 20 Years

Complies with Full Industrial Temperature Range

Industry Standard Green (Pb/Halide-free/RoHS Compliant) Package Options

 8-lead SOIC (150-mil)

 8-pad Ultra Thin DFN (2 x 3 x 0.6 mm)

 8-pad Ultra Thin DFN (5 x 6 x 0.6 mm)

 8-lead TSSOP Package

 8-ball WLCSP⁽¹⁾

Note: 1. Contact factory for availability.

DS-25XE021A–061I–9/2017

1.

Description

The Adesto^®AT25XE021A is a serial interface Flash memory device designed for use in a wide variety of high-volume consumer

based applications in which program code is shadowed from Flash memory into embedded or external RAM for execution. The

flexible erase architecture of the AT25XE021A, with its page erase granularity it is ideal for data storage as well, eliminating the

need for additional data storage devices.

The erase block sizes of the AT25XE021A have been optimized to meet the needs of today's code and data storage applications.

By optimizing the size of the erase blocks, the memory space can be used much more efficiently. Because certain code modules

and data storage segments must reside by themselves in their own erase regions, the wasted and unused memory space that

occurs with large sectored and large block erase Flash memory devices can be greatly reduced. This increased memory space

efficiency allows additional code routines and data storage segments to be added while still maintaining the same overall device

density.

The device also contains a specialized OTP (One-Time Programmable) Security Register that can be used for purposes such as

unique device serialization, system-level Electronic Serial Number (ESN) storage, locked key storage, etc.

Specifically designed for use in many different systems, the AT25XE021A supports read, program, and erase operations with a

wide supply voltage range of 1.65V to 3.6V. No separate voltage is required for programming and erasing.

2.

Pin Descriptions and Pinouts

Table 2-1. Pin Descriptions

Asserted

State

Symbol

Name and Function

Type

CHIP SELECT: Asserting the CS pin selects the device. When the CS pin is deasserted, the

device will be deselected and normally be placed in standby mode (not Deep Power-Down

mode), and the SO pin will be in a high-impedance state. When the device is deselected, data

will not be accepted on the SI pin.

CS

Low

Input

A high-to-low transition on the CS pin is required to start an operation, and a low-to-high

transition is required to end an operation. When ending an internally self-timed operation such

as a program or erase cycle, the device will not enter the standby mode until the completion of

the operation.

SERIAL CLOCK: This pin is used to provide a clock to the device and is used to control the flow

of data to and from the device. Command, address, and input data present on the SI pin is

always latched in on the rising edge of SCK, while output data on the SO pin is always clocked

out on the falling edge of SCK.

SCK

-

Input

SERIAL INPUT: The SI pin is used to shift data into the device. The SI pin is used for all data

input including command and address sequences. Data on the SI pin is always latched in on the

rising edge of SCK.

With the Dual-Output Read commands, the SI Pin becomes an output pin (I/O₀) in conjunction

with other pins to allow two bits of data on (I/O_1-0) to be clocked out on every falling edge of SCK.

Input/

Output

SI (I/O₀)

-

To maintain consistency with the SPI nomenclature, the SI (I/O₀) pin will be referenced as the SI

pin unless specifically addressing the Dual-I/O modes in which case it will be referenced as I/O_0.

Data present on the SI pin will be ignored whenever the device is deselected (CS is deasserted).

SERIAL OUTPUT: The SO pin is used to shift data out from the device. Data on the SO pin is

always clocked out on the falling edge of SCK.

With the Dual-Output Read commands, the SO Pin remains an output pin (I/O₁) in conjunction

with other pins to allow two bits of data on (I/O_1-0) to be clocked out on every falling edge of SCK.

Input/

Output

-

SO (I/O₁)

To maintain consistency with the SPI nomenclature, the SO (I/O₁) pin will be referenced as the

SO pin unless specifically addressing the Dual-I/O modes in which case it ise referenced as I/O_1.

The SO pin will be in a high-impedance state whenever the device is deselected (CS is

deasserted).

AT25XE021A

DS-25XE021A–061I–9/2017

2

Table 2-1. Pin Descriptions (Continued)

Asserted

State

Symbol

Name and Function

Type

WRITE PROTECT: The WP pin controls the hardware locking feature of the device. Please refer

to “Protection Commands and Features” on page 17 for more details on protection features and

the WP pin.

WP

Low

Input

The WP pin is internally pulled-high and may be left floating if hardware controlled protection will

not be used. However, it is recommended that the WP pin also be externally connected to V_CC

whenever possible.

HOLD: The HOLD pin is used to temporarily pause serial communication without deselecting or

resetting the device. While the HOLD pin is asserted, transitions on the SCK pin and data on the

SI pin will be ignored, and the SO pin will be in a high-impedance state.

The CS pin must be asserted, and the SCK pin must be in the low state in order for a Hold

condition to start. A Hold condition pauses serial communication only and does not have an

effect on internally self-timed operations such as a program or erase cycle. Please refer to

“Hold” on page 35 for additional details on the Hold operation.The HOLD pin is internally

pulled-high and may be left floating if the Hold function will not be used. However, it is

recommended that the HOLD pin also be externally connected to V_CCwhenever possible.

HOLD

Low

Input

DEVICE POWER SUPPLY: The V_CCpin is used to supply the source voltage to the device.

V_CC

-

Power

Operations at invalid V_CCvoltages may produce spurious results and should not be attempted.

GROUND: The ground reference for the power supply. GND should be connected to the system

ground.

GND

Table 2-2.

Pinouts

Figure 2-1. 8-SOIC Top View

Figure 2-3. 8-UDFN Top View

1

8

7

6

5

CS

VCC

CS

SO

1

2

3

4

8

7

6

5

VCC

HOLD

SCK

SI

2

SO

HOLD

SCK

SI

WP

3

4

WP

GND

Figure 2-4. WLCSP Bottom View⁽¹⁾

Figure 2-2. 8-TSSOP Top View

SCK

WP

CS

SO

1

2

3

4

8

7

6

5

VCC

SI

HOLD

SCK

SI

SO

CS

HOLD

Vcc

GND

WP

GND

A1

Note: 1. Contact info@adestotech.com for manufacturing flow and availability.

AT25XE021A

DS-25XE021A–061I–9/2017

3

3.

Block Diagram

Figure 3-1. Block Diagram

&21752/ꢁ$1'

3527(&7,21 /2*,&

,ꢃ2ꢁ%8))(56

$1'ꢁ/$7&+(6

&6

65$0

'$7$ꢁ %8))(5

6&.

,17(5)$&(

&21752/

$1'

6,ꢁꢂ,ꢃ2ꢄ

<ꢀ'(&2'(5

<ꢀ *$7,1*

/2*,&

62

)/$6+

0(025<

$55$<

:3

;ꢀ'(&2'(5

+2/'

AT25XE021A

DS-25XE021A–061I–9/2017

4

4.

Memory Array

To provide the greatest flexibility, the memory array of the AT25XE021A can be erased in three levels of granularity

including a full chip erase. The size of the erase blocks is optimized for both code and data storage applications, allowing

both code and data segments to reside in their own erase regions. The Memory Architecture Diagram illustrates the

breakdown of each erase level.

Figure 4-1. Memory Architecture Diagram

Block Erase Detail

Page Program Detail

Internal Sectoring for

Sector Protection

Function

64KB

Block Erase

32KB

Block Erase

4KB

Block Erase

1-256 Byte

Page Program

(02h Command)

Block Address

Range

Page Address

Range

(D8h Command) (52h Command) (20h Command)

4KB

03FFFFh – 03F000h

03EFFFh – 03E000h

03DFFFh – 03D000h

03CFFFh – 03C000h

03BFFFh – 03B000h

03AFFFh – 03A000h

039FFFh – 039000h

038FFFh – 038000h

037FFFh – 037000h

036FFFh – 036000h

035FFFh – 035000h

034FFFh – 034000h

033FFFh – 033000h

032FFFh – 032000h

031FFFh – 031000h

030FFFh – 030000h

02FFFFh – 02F000h

02EFFFh – 02E000h

02DFFFh – 02D000h

02CFFFh – 02C000h

02BFFFh – 02B000h

02AFFFh – 02A000h

029FFFh – 029000h

028FFFh – 028000h

027FFFh – 027000h

026FFFh – 026000h

025FFFh – 025000h

024FFFh – 024000h

023FFFh – 023000h

022FFFh – 022000h

021FFFh – 021000h

020FFFh – 020000h

256 Bytes

03FFFFh – 03FF00h

03FEFFh – 03FE00h

03FDFFh – 03FD00h

03FCFFh – 03FC00h

03FBFFh – 03FB00h

03FAFFh – 03FA00h

03F9FFh – 03F900h

03F8FFh – 03F800h

03F7FFh – 03F700h

03F6FFh – 03F600h

03F5FFh – 03F500h

03F4FFh – 03F400h

03F3FFh – 03F300h

03F2FFh – 03F200h

03F1FFh – 03F100h

03F0FFh – 03F000h

03EFFFh – 03EF00h

03EEFFh – 03EE00h

03EDFFh – 03ED00h

03ECFFh – 03EC00h

03EBFFh – 03EB00h

03EAFFh – 03EA00h

03E9FFh – 03E900h

03E8FFh – 03E800h

4KB

32KB

4KB

64KB

(Sector 3)

64KB

4KB

32KB

4KB

32KB

4KB

64KB

(Sector 2)

64KB

4KB

256 Bytes

0017FFh – 001700h

0016FFh – 001600h

0015FFh – 001500h

0014FFh – 001400h

0013FFh – 001300h

0012FFh – 001200h

0011FFh – 001100h

0010FFh – 001000h

000FFFh – 000F00h

000EFFh – 000E00h

000DFFh – 000D00h

000CFFh – 000C00h

000BFFh – 000B00h

000AFFh – 000A00h

0009FFh – 000900h

0008FFh – 000800h

0007FFh – 000700h

0006FFh – 000600h

0005FFh – 000500h

0004FFh – 000400h

0003FFh – 000300h

0002FFh – 000200h

0001FFh – 000100h

0000FFh – 000000h

32KB

4KB

00FFFFh – 00F000h

00EFFFh – 00E000h

00DFFFh – 00D000h

00CFFFh – 00C000h

00BFFFh – 00B000h

00AFFFh – 00A000h

009FFFh – 009000h

008FFFh – 008000h

007FFFh – 007000h

006FFFh – 006000h

005FFFh – 005000h

004FFFh – 004000h

003FFFh – 003000h

002FFFh – 002000h

001FFFh – 001000h

000FFFh – 000000h

4KB

32KB

4KB

64KB

(Sector 0)

64KB

4KB

32KB

4KB

AT25XE021A

DS-25XE021A–061I–9/2017

5

5.

Device Operation

The AT25XE021A is controlled by a set of instructions that are sent from a host controller, commonly referred to as the

SPI Master. The SPI Master communicates with the AT25XE021A via the SPI bus which is comprised of four signal lines:

Chip Select (CS), Serial Clock (SCK), Serial Input (SI), and Serial Output (SO).

The SPI protocol defines a total of four modes of operation (mode 0, 1, 2, or 3) with each mode differing in respect to the

SCK polarity and phase and how the polarity and phase control the flow of data on the SPI bus. The AT25XE021A

supports the two most common modes, SPI Modes 0 and 3. The only difference between SPI Modes 0 and 3 is the

polarity of the SCK signal when in the inactive state (when the SPI Master is in standby mode and not transferring any

data). With SPI Modes 0 and 3, data is always latched in on the rising edge of SCK and always output on the falling edge

of SCK.

Figure 5-1. SPI Mode 0 and 3

CS

SCK

MSB

LSB

SI

MSB

LSB

SO

5.1

Dual Output Read

The AT25XE021A features a Dual-Output Read mode that allow two bits of data to be clocked out of the device every

clock cycle to improve throughput. To accomplish this, both the SI and SO pins are utilized as outputs for the transfer of

data bytes. With the Dual-Output Read Array command, the SI pin becomes an output along with the SO pin.

6.

Commands and Addressing

A valid instruction or operation must always be started by first asserting the CS pin. After the CS pin has been asserted,

the host controller must then clock out a valid 8-bit opcode on the SPI bus. Following the opcode, instruction dependent

information such as address and data bytes would then be clocked out by the host controller. All opcode, address, and

data bytes are transferred with the most-significant bit (MSB) first. An operation is ended by deasserting the CS pin.

Opcodes not supported by the AT25XE021A will be ignored by the device and no operation will be started. The device

will continue to ignore any data presented on the SI pin until the start of the next operation (CS pin being deasserted and

then reasserted). In addition, if the CS pin is deasserted before complete opcode and address information is sent to the

device, then no operation will be performed and the device will simply return to the idle state and wait for the next

operation.

Addressing of the device requires a total of three bytes of information to be sent, representing address bits A23-A0.

Since the upper address limit of the AT25XE021A memory array is 03FFFFh, address bits A23-A18 are always ignored

by the device.

AT25XE021A

DS-25XE021A–061I–9/2017

6

Table 6-1. Command Listing

Clock

Frequency

Address

Bytes

Dummy

Bytes

Data

Bytes

Command

Opcode

Read Commands

0Bh

03h

3Bh

0000 1011

Up to 70MHz

Up to 25MHz

Up to 40MHz

3

1

0

1

1+

Read Array

0000 0011

0011 1011

Dual Output Read

Program and Erase Commands

Page Erase

81h

20h

52h

D8h

60h

C7h

02h

ADh

AFh

A2h

1000 0001

0010 0000

0101 0010

1101 1000

0110 0000

1100 0111

0000 0010

1010 1101

1010 1111

1010 0010

Up to 70MHz

3

0

Block Erase (4 Kbytes)

Block Erase (32 Kbytes)

Block Erase (64 Kbytes)

3

0

3

0

Chip Erase

0

3

0

Byte/Page Program (1 to 256 Bytes)

Sequential Program Mode

1+

1

3, 0 ⁽¹⁾

3

1

Dual-Input Byte/Page Program (1 to 256 bytes)

Protection Commands

Write Enable

1+

06h

04h

36h

39h

3Ch

0000 0110

0000 0100

0011 0110

0011 1001

0011 1100

Up to 70MHz

0

3

0

Write Disable

Protect Sector

0

Unprotect Sector

0

Read Sector Protection Registers

Security Commands

1+

Program OTP Security Register

Read OTP Security Register

Status Register Commands

Read Status Register

9Bh

77h

1001 1011

0111 0111

Up to 70MHz

3

0

2

1+

05h

25h

01h

31h

0000 0101

0010 0101

0000 0001

0011 0001

Up to 70MHz

0

1

0

1+

0

Active Status Interrupt

Write Status Register Byte 1

Write Status Register Byte 2

Miscellaneous Commands

Reset

1

F0h

1111 0000

Up to 70MHz

0

1(D0h)

AT25XE021A

DS-25XE021A–061I–9/2017

7

Table 6-1. Command Listing

Clock

Frequency

Address

Bytes

Dummy

Bytes

Data

Bytes

Command

Opcode

1001 1111

Read Manufacturer and Device ID

Deep Power-Down

9Fh

B9h

ABh

79h

Up to 70MHz

0

1 to 4

1011 1001

1010 1011

0111 1001

0

Resume from Deep Power-Down

Ultra Deep Power-Down

1. Three address bytes are required for the first operation to designate the address to start programming. Afterwards, the internal address counter automatically

increments, so subsequent Sequential Program Mode operations only require clocking in of the opcode and the data byte until the Sequential Program Mode has been

exited.

7.

Read Commands

7.1

Read Array

The Read Array command can be used to sequentially read a continuous stream of data from the device by simply

providing the clock signal once the initial starting address is specified. The device incorporates an internal address

counter that automatically increments every clock cycle.

Two opcodes (0Bh and 03h) can be used for the Read Array command. The use of each opcode depends on the

maximum clock frequency that will be used to read data from the device. The 0Bh opcode can be used at any clock

frequency up to the maximum specified by f_CLK, and the 03h opcode can be used for lower frequency read operations up

to the maximum specified by f_RDLF

.

To perform the Read Array operation, the CS pin must first be asserted and the appropriate opcode (0Bh or 03h) must be

clocked into the device. After the opcode has been clocked in, the three address bytes must be clocked in to specify the

starting address location of the first byte to read within the memory array. Following the three address bytes, an

additional dummy byte needs to be clocked into the device if the 0Bh opcode is used for the Read Array operation.

After the three address bytes (and the dummy byte if using opcode 0Bh) have been clocked in, additional clock cycles

will result in data being output on the SO pin. The data is always output with the MSB of a byte first. When the last byte

(03FFFFh) of the memory array has been read, the device will continue reading back at the beginning of the array

(000000h). No delays will be incurred when wrapping around from the end of the array to the beginning of the array.

Deasserting the CS pin will terminate the read operation and put the SO pin into high-impedance state. The CS pin can

be deasserted at any time and does not require a full byte of data be read.

Figure 7-1. Read Array - 03h Opcode

CS

0

1

2

3

4

5

6

7

8

9

10 11 12

29 30 31 32 33 34 35 36 37 38 39 40

SCK

SI

OPCODE

ADDRESS BITS A23-A0

0

1

A

MSB

DATA BYTE 1

HIGH-IMPEDANCE

D

SO

MSB

AT25XE021A

DS-25XE021A–061I–9/2017

8

Figure 7-2. Read Array - 0Bh Opcode

S

0

1

2

3

4

5

6

7

8

9

10 11 12

29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

K

I

OPCODE

ADDRESS BITS A23-A0

DON'T CARE

0

1

0

1

A

X

MSB

DATA BYTE 1

HIGH-IMPEDANCE

D

O

MSB

7.2

Dual-Output Read Array

The Dual-Output Read Array command is similar to the standard Read Array command and can be used to sequentially

read a continuous stream of data from the device by simply providing the clock signal once the initial starting address has

been specified. Unlike the standard Read Array command, however, the Dual-Output Read Array command allows two

bits of data to be clocked out of the device on every clock cycle, rather than just one.

The Dual-Output Read Array command can be used at any clock frequency, up to the maximum specified by f_RDDO. To

perform the Dual-Output Read Array operation, the CS pin must first be asserted and then the opcode 3Bh must be

clocked into the device. After the opcode has been clocked in, the three address bytes must be clocked in to specify the

location of the first byte to read within the memory array. Following the three address bytes, a single dummy byte must

also be clocked into the device.

After the three address bytes and the dummy byte have been clocked in, additional clock cycles will result in data being

output on both the SO and SI pins. The data is always output with the MSB of a byte first and the MSB is always output

on the SO pin. During the first clock cycle, bit seven of the first data byte is output on the SO pin, while bit six of the same

data byte is output on the SIO pin. During the next clock cycle, bits five and four of the first data byte are output on the SO

and SIO pins, respectively. The sequence continues with each byte of data being output after every four clock cycles.

When the last byte (03FFFFh) of the memory array has been read, the device will continue reading from the beginning of

the array (000000h). No delays will be incurred when wrapping around from the end of the array to the beginning of the

array.Deasserting the CS pin will terminate the read operation and put the SO and SI pins into a high-impedance state.

The CS pin can be deasserted at any time and does not require that a full byte of data be read.

Figure 7-3. Dual-Output Read Array

&6

ꢈ

ꢇ

ꢅ

ꢆ

ꢌ

ꢋ

ꢉ

ꢊ

ꢎ

ꢍ

ꢇꢈ ꢇꢇ ꢇꢅ

ꢅꢍ ꢆꢈ ꢆꢇ ꢆꢅ ꢆꢆ ꢆꢌ ꢆꢋ ꢆꢉ ꢆꢊ ꢆꢎ ꢆꢍ ꢌꢈ ꢌꢇ ꢌꢅ ꢌꢆ ꢌꢌ ꢌꢋ ꢌꢉ ꢌꢊ ꢌꢎ

6&.

6,ꢁꢂ6,2ꢄ

62

287387

23&2'(

$''5(66ꢁ%,76ꢁ$ꢅꢆꢀ$ꢈꢁ

'21ꢏ7ꢁꢁ&$5(

'$7$ꢁ%<7(ꢇ

'$7$ꢁ%<7(ꢅ

'

ꢌ

'

ꢅ

'

ꢌ

'

ꢅ

'

ꢌ

ꢈ

06%

ꢈ

ꢇ

ꢈ

ꢇ

$

06%

$

;

06%

;

ꢉ

ꢈ

ꢉ

ꢈ

ꢉ

+,*+ꢀ,03('$1&(

'

ꢋ

'

ꢆ

'

ꢋ

'

ꢆ

'

ꢊ

'

ꢋ

ꢊ

ꢇ

ꢊ

ꢇ

06%

AT25XE021A

DS-25XE021A–061I–9/2017

9

8.

Program and Erase Commands

8.1

Byte/Page Program

The Byte/Page Program command allows anywhere from a single byte of data to 256 bytes of data to be programmed

into previously erased memory locations. An erased memory location is one that has all eight bits set to the logical “1”

state (a byte value of FFh). Before a Byte/Page Program command can be started, the Write Enable command must

have been previously issued to the device (see “Write Enable” on page 17) to set the Write Enable Latch (WEL) bit of the

Status Register to a logical “1” state.

To perform a Byte/Page Program command, an opcode of 02h must be clocked into the device followed by the three

address bytes denoting the first byte location of the memory array to begin programming at. After the address bytes have

been clocked in, data can then be clocked into the device and will be stored in an internal buffer.

If the starting memory address denoted by A23-A0 does not fall on an even 256-byte page boundary (A7-A0 are not all

0), then special circumstances regarding which memory locations to be programmed will apply. In this situation, any data

that is sent to the device that goes beyond the end of the page will wrap around back to the beginning of the same page.

For example, if the starting address denoted by A23-A0 is 0000FEh, and three bytes of data are sent to the device, then

the first two bytes of data will be programmed at addresses 0000FEh and 0000FFh while the last byte of data will be

programmed at address 000000h. The remaining bytes in the page (addresses 000001h through 0000FDh) will not be

programmed and will remain in the erased state (FFh). In addition, if more than 256 bytes of data are sent to the device,

then only the last 256 bytes sent will be latched into the internal buffer.

When the CS pin is deasserted, the device will take the data stored in the internal buffer and program it into the

appropriate memory array locations based on the starting address specified by A23-A0 and the number of data bytes

sent to the device. If less than 256 bytes of data were sent to the device, then the remaining bytes within the page will not

be programmed and will remain in the erased state (FFh). The programming of the data bytes is internally self-timed and

should take place in a time of t_PPor t_BPif only programming a single byte.

The three address bytes and at least one complete byte of data must be clocked into the device before the CS pin is

deasserted, and the CS pin must be deasserted on even byte boundaries (multiples of eight bits); otherwise, the device

will abort the operation and no data will be programmed into the memory array. In addition, if the memory is in the

protected state (see “Protect Sector” on page 19), then the Byte/Page Program command will not be executed, and the

device will return to the idle state once the CS pin has been deasserted. The WEL bit in the Status Register will be reset

back to the logical “0” state if the program cycle aborts due to an incomplete address being sent, an incomplete byte of

data being sent, the CS pin being deasserted on uneven byte boundaries, or because the memory location to be

programmed is protected.

While the device is programming, the Status Register can be read and will indicate that the device is busy. For faster

throughput, it is recommended that the Status Register be polled rather than waiting the t_BPor t_PPtime to determine if the

data bytes have finished programming. For fastest throughput and least power consumption, it is recommended that the

Active Status Interrupt command 25h be used. After the initial 16 clks, no more clocks are required. Once the BUSY

cycle is done, SO will be driven low immediately to signal the device has finished programming.At some point before the

program cycle completes, the WEL bit in the Status Register will be reset back to the logical “0” state.

The device also incorporates an intelligent programming algorithm that can detect when a byte location fails to program

properly. If a programming error arises, it will be indicated by the EPE bit in the Status Register.

AT25XE021A

DS-25XE021A–061I–9/2017

1 0

Figure 8-1. Byte Program

CS

0

1

2

3

4

5

6

7

8

9

10 11 12

29 30 31 32 33 34 35 36 37 38 39

SCK

SI

OPCODE

ADDRESS BITS A23-A0

DATA IN

0

1

0

A

D

MSB

HIGH-IMPEDANCE

SO

Figure 8-2. Page Program

CS

0

1

2

3

4

5

6

7

8

9

29 30 31 32 33 34 35 36 37 38 39

SCK

OPCODE

ADDRESS BITS A23-A0

DATA IN BYTE 1

DATA IN BYTE n

0

1

0

A

D

SI

MSB

HIGH-IMPEDANCE

SO

8.2

Dual-Input Byte/Page Program

The Dual-Input Byte/Page Program command is similar to the standard Byte/Page Program command and can be used

to program anywhere from a single byte of data up to 256 bytes of data into previously erased memory locations. Unlike

the standard Byte/Page Program command, however, the Dual-Input Byte/Page Program command allows two bits of

data to be clocked into the device on every clock cycle rather than just one.

Before the Dual-Input Byte/Page Program command can be started, the Write Enable command must have been

previously issued to the device (see “Write Enable” on page 17) to set the Write Enable Latch (WEL) bit of the Status

Register to a Logical 1 state. To perform a Dual-Input Byte/Page Program command, an A2h opcode must be clocked

into the device followed by the three address bytes denoting the first location of the memory array to begin programming

at. After the address bytes have been clocked in, data can then be clocked into the device two bits at a time on both the

SO and SI pins.

The data is always input with the MSB of a byte first, and the MSB is always input on the SO pin. During the first clock

cycle, bit seven of the first data byte is input on the SO pin while bit six of the same data byte is input on the SI pin. During

the next clock cycle, bits five and four of the first data byte are input on the SO and SI pins, respectively. The sequence

continues with each byte of data being input after every four clock cycles. Like the standard Byte/Page Program

command, all data clocked into the device are stored in an internal buffer.

If the starting memory address denoted by A23-A0 does not fall on an even 256-byte page boundary (A7-A0 are not all

0), then special circumstances regarding which memory locations are to be programmed will apply. In this situation, any

data that are sent to the device that go beyond the end of the page will wrap around to the beginning of the same page.

In addition, if more than 256 bytes of data is sent to the device, then only the last 256 bytes sent will be latched into the

internal buffer.

Example: If the starting address denoted by A23-A0 is 0000FEh and three bytes of data are sent to the device, then

the first two bytes of data will be programmed at addresses 0000FEh and 0000FFh, while the last byte of

AT25XE021A

DS-25XE021A–061I–9/2017

1 1

data will be programmed at address 000000h. The remaining bytes in the page (addresses 000001h

through 0000FDh) will not be programmed and will remain in the erased state (FFh).

When the CS pin is deasserted, the device will program the data stored in the internal buffer into the appropriate memory

array locations based on the starting address specified by A23-A0 and the number of data bytes sent to the device. If

fewer than 256 bytes of data is sent to the device, then the remaining bytes within the page will not be programmed and

will remain in the erased state (FFh). The programming of the data bytes is internally self-timed and should take place in

a time of t_PPor t_BPif only programming a page (t_PP)or a single byte (t_BP)

.

The three address bytes and at least one complete byte of data must be clocked into the device before the CS pin is

deasserted, and the CS pin must be deasserted on even byte boundaries (multiples of eight bits); otherwise, the device

will abort the operation and no data will be programmed into the memory array. In addition, if the address specified by

A23-A0 points to a memory location within a sector that is in the protected state (see “Protect Sector” on page 19), then

the Byte/Page Program command will not be executed and the device will return to the idle state once the CS pin has

been deasserted. The WEL bit in the Status Register will be reset back to the Logical 0 state if the program cycle aborts

due to an incomplete address being sent, an incomplete byte of data being sent, the CS pin being deasserted on uneven

byte boundaries, or because the memory location to be programmed is protected or locked down.

While the device is programming, the Status Register can be read and will indicate that the device is busy. For faster

throughput, it is recommended that the Status Register be polled rather than waiting the t_BPor t_PPtime to determine if the

data bytes have finished programming. For fastest throughput and least power consumption, it is recommended that

the Active Status Interrupt command 25h be used. At some point before the program cycle completes, the WEL bit in

the Status Register will be reset back to the Logical 0 state.

The device also incorporates an intelligent programming algorithm that can detect when a byte location fails to program

properly. If a programming error arises, it will be indicated by the EPE bit in the Status Register.

Figure 8-3. Dual-Input Byte Program

CS

0

1

2

3

4

5

6

7

8

9

10 11 12

29 30 31 32 33 34 35

SCK

SI (SIO)

SO (SOI)

Input

Opcode

Address Bits A23-A0

Data Byte

D

1

MSB

0

1

0

1

0

A

MSB

A

6

7

4

2

0

1

High-impedance

D

5

3

MSB

AT25XE021A

DS-25XE021A–061I–9/2017

1 2

Figure 8-4. Dual-Input Page Program

CS

0

1

2

3

4

5

6

7

8

9

10 11 12

29 30 31 32 33 34 35 36 37 38 39

SCK

SI (SIO)

SO (SOI)

Input

Opcode

Address Bits A23-A0

Data Byte 1

Data Byte 2

Data Byte n

D

4

D

1

MSB

0

1

0

1

0

A

MSB

A

6

4

2

0

1

6

4

2

0

1

6

2

0

1

High-impedance

D

5

D

7

5

3

7

5

3

7

3

MSB

8.3

Sequential Program Mode

The Sequential Program Mode improves throughput over the Byte/Page Program command when the Byte/Page

Program command is used to program single bytes only into consecutive address locations. For example, some systems

may be designed to program only a single byte of information at a time and cannot utilize a buffered Page Program

operation due to design restrictions. In such a case, the system would normally have to perform multiple Byte Program

operations in order to program data into sequential memory locations. This approach can add considerable system

overhead and SPI bus traffic.

The Sequential Programming Mode helps reduce system overhead and bus traffic by incorporating an internal address

counter that keeps track of the byte location to program, thereby eliminating the need to supply an address sequence to

the device for every byte to program. When using the Sequential Program mode, all address locations to be programmed

must be in the erased state. Before the Sequential Program mode can first be entered, the Write Enable command must

have been previously issued to the device to set the WEL bit of the Status Register to a logical “1” state.

To start the Sequential Program Mode, the CS pin must first be asserted, and either an opcode of ADh or AFh must be

clocked into the device. For the first program cycle, three address bytes must be clocked in after the opcode to designate

the first byte location to program. After the address bytes have been clocked in, the byte of data to be programmed can

be sent to the device. Deasserting the CS pin will start the internally self-timed program operation, and the byte of data

will be programmed into the memory location specified by A23 - A0.

After the first byte has been successfully programmed, a second byte can be programmed by simply reasserting the CS

pin, clocking in the ADh or AFh opcode, and then clocking in the next byte of data. When the CS pin is deasserted, the

second byte of data will be programmed into the next sequential memory location. The process would be repeated for

any additional bytes. There is no need to reissue the Write Enable command once the Sequential Program Mode has

been entered.

When the last desired byte has been programmed into the memory array, the Sequential Program Mode operation can

be terminated by reasserting the CS pin and sending the Write Disable command to the device to reset the WEL bit in the

Status Register back to the logical “0” state.

If more than one byte of data is ever clocked in during each program cycle, then only the last byte of data sent on the SI

pin will be stored in the internal latches. The programming of each byte is internally self-timed and should take place in a

time of t_BP. For each program cycle, a complete byte of data must be clocked into the device before the CS pin is

deasserted, and the CS pin must be deasserted on even byte boundaries (multiples of eight bits); otherwise, the device

will abort the operation, the byte of data will not be programmed into the memory array, and the WEL bit in the Status

Register will be reset back to the logical “0” state.

AT25XE021A

DS-25XE021A–061I–9/2017

1 3

If the address initially specified by A23 - A0 points to a memory location within a sector that is in the protected state, then

the Sequential Program Mode command will not be executed, and the device will return to the idle state once the CS pin

has been deasserted. The WEL bit in the Status Register will also be reset back to the logical “0” state.

There is no address wrapping when using the Sequential Program Mode. Therefore, when the last byte (03FFFFh) of the

memory array has been programmed, the device will automatically exit the Sequential Program mode and reset the WEL

bit in the Status Register back to the logical “0” state. In addition, the Sequential Program mode will not automatically skip

over protected sectors; therefore, once the highest unprotected memory location in a programming sequence has been

programmed, the device will automatically exit the Sequential Program mode and reset the WEL bit in the Status

Register. For example, if Sector 1 was protected and Sector 0 was currently being programmed, once the last byte of

Sector 0 was programmed, the Sequential Program mode would automatically end. To continue programming with

Sector 2, the Sequential Program mode would have to be restarted by supplying the ADh or AFh opcode, the three

address bytes, and the first byte of Sector 2 to program.

While the device is programming a byte, the Status Register can be read and will indicate that the device is busy. For

faster throughput, it is recommended that the Status Register be polled at the end of each program cycle rather than

waiting the t_BPtime to determine if the byte has finished programming before starting the next Sequential Program mode

cycle.

The device also incorporates an intelligent programming algorithm that can detect when a byte location fails to program

properly. If a programming error arises, it will be indicated by the EPE bit in the Status Register.

Figure 8-5. Sequential Program Mode – Status Register Polling

CS

Seqeuntial Program Mode

Status Register Read Seqeuntial Program Mode

Seqeuntial Program Mode Write Disable

Command

Opcode

A

23-16

A15-8

A7-0

Data

05h

Opcode Data

05h

Opcode Data

04h

05h

SI

First Address to Program

STATUS REGISTER

DATA

STATUS REGISTER

DATA

STATUS REGISTER

DATA

HIGH-IMPEDANCE

SO

Note: Each transition

shown for SI represents one byte (8 bits)

Figure 8-6. Sequential Program Mode – Waiting Maximum Byte Program Time

CS

t_BP

Seqeuntial Program Mode

Write Disable

Command

Opcode A23-16 A15-8

A7-0

Data

Opcode Data

04h

SI

First Address to Program

HIGH-IMPEDANCE

SO

Note: Each transition

shown for SI represents one byte (8 bits)

AT25XE021A

DS-25XE021A–061I–9/2017

1 4

8.4

Page Erase

Page Erase for 2Mbit, 1024 Pages [ten (10) page address bits, PA<9:0>] of 256Bytes each.

The Page Erase command can be used to individually erase any page in the main memory array. The Main Memory

Byte/Page Program command can be utilized at a later time.

To perform a Page Erase with the standard page size (256 bytes), an opcode of 81h must be clocked into the device

followed by three address bytes comprised of:

Byte 0: 81h the page erase command code

Byte 1: XXXX XX, PA9, PA8; which is six (6) dummy bits and two (2) page address bits

Byte 2: PA<7:0>; which is eight (8) page address bits

Byte 3: XXXX XXXX; which is eight (8) dummy bits

When a low-to-high transition occurs on the CS pin, the device will erase the selected page (the erased state is a Logic

1). The erase operation is internally self-timed and should take place in a maximum time of t_PE. During this time, the

RDY/BUSY bit in the Status Register will indicate that the device is busy.

The device also incorporates an intelligent erase algorithm that can detect when a byte location fails to erase properly. If

an erase error arises, it will be indicated by the EPE bit in the Status Register.

8.5

Block Erase

A block of 4, 32, or 64Kbytes can be erased (all bits set to the logical “1” state) in a single operation by using one of three

different opcodes for the Block Erase command. An opcode of 20h is used for a 4-Kbyte erase, an opcode of 52h for a

32-Kbyte erase, and an opcode of D8h is used for a 64-Kbyte erase. Before a Block Erase command can be started, the

Write Enable command must have been previously issued to the device to set the WEL bit of the Status Register to a

logical “1” state.

To perform a Block Erase, the CS pin must first be asserted and the appropriate opcode (20h, 52h, or D8h) must be

clocked into the device. After the opcode has been clocked in, the three address bytes specifying an address within the

4-, 32-, or 64-Kbyte block to be erased must be clocked in. Any additional data clocked into the device will be ignored.

When the CS pin is deasserted, the device will erase the appropriate block. The erasing of the block is internally self-

timed and should take place in a time of t_BLKE

.

Since the Block Erase command erases a region of bytes, the lower order address bits do not need to be decoded by the

device. Therefore, for a 4-Kbyte erase, address bits A11-A0 will be ignored by the device and their values can be either a

logical “1” or “0”. For a 32-Kbyte erase, address bits A14-A0 will be ignored by the device. For a 64-Kbyte erase, address

bits A15-A0 will be ignored by the device. Despite the lower order address bits not being decoded by the device, the

complete three address bytes must still be clocked into the device before the CS pin is deasserted, and the CS pin must

be deasserted on an even byte boundary (multiples of eight bits); otherwise, the device will abort the operation and no

erase operation will be performed.

If the memory is in the protected state, then the Block Erase command will not be executed, and the device will return to

the idle state once the CS pin has been deasserted.

The WEL bit in the Status Register will be reset back to the logical “0” state if the erase cycle aborts due to an incomplete

address being sent, the CS pin being deasserted on uneven byte boundaries, or because a memory location within the

region to be erased is protected.

While the device is executing a successful erase cycle, the Status Register can be read and will indicate that the device

is busy. For faster throughput, it is recommended that the Status Register be polled rather than waiting the t_BLKEtime to

determine if the device has finished erasing. At some point before the erase cycle completes, the WEL bit in the Status

Register will be reset back to the logical “0” state.

For fastest throughput and least power consumption, it is recommended that the Active Status Interrupt command 25h be

used. After the initial 16 clks, no more clocks are required. Once the BUSY cycle is done, SO will be driven low

immediately to signal the device has finished erasing.

AT25XE021A

DS-25XE021A–061I–9/2017

1 5

The device also incorporates an intelligent erase algorithm that can detect when a byte location fails to erase properly. If

an erase error occurs, it will be indicated by the EPE bit in the Status Register.

Figure 8-7. Block Erase

CS

0

1

2

3

4

5

6

7

8

9

10 11 12

26 27 28 29 30 31

SCK

SI

OPCODE

ADDRESS BITS A23-A0

C

A

MSB

HIGH-IMPEDANCE

SO

8.6

Chip Erase

The entire memory array can be erased in a single operation by using the Chip Erase command. Before a Chip Erase

command can be started, the Write Enable command must have been previously issued to the device to set the WEL bit

of the Status Register to a logical “1” state.

Two opcodes (60h and C7h) can be used for the Chip Erase command. There is no difference in device functionality

when utilizing the two opcodes, so they can be used interchangeably. To perform a Chip Erase, one of the two opcodes

must be clocked into the device. Since the entire memory array is to be erased, no address bytes need to be clocked into

the device, and any data clocked in after the opcode will be ignored. When the CS pin is deasserted, the device will erase

the entire memory array. The erasing of the device is internally self-timed and should take place in a time of t_CHPE

.

The complete opcode must be clocked into the device before the CS pin is deasserted, and the CS pin must be

deasserted on an even byte boundary (multiples of eight bits); otherwise, no erase will be performed. In addition, if any

sector in the memory array is in the protected state, then the Chip Erase command will not be executed, and the device

will return to the idle state once the CS pin has been deasserted. The WEL bit in the Status Register will be reset back to

the logical “0” state if the CS pin is deasserted on uneven byte boundaries or if the memory is in the protected state.

While the device is executing a successful erase cycle, the Status Register can be read and will indicate that the device

is busy. For faster throughput, it is recommended that the Status Register be polled rather than waiting the t_CHPEtime to

determine if the device has finished erasing. At some point before the erase cycle completes, the WEL bit in the Status

Register will be reset back to the logical “0” state.

The device also incorporates an intelligent erase algorithm that can detect when a byte location fails to erase properly. If

an erase error occurs, it will be indicated by the EPE bit in the Status Register.

Figure 8-8. Chip Erase

CS

0

1

2

3

4

5

6

7

SCK

SI

OPCODE

C

MSB

HIGH-IMPEDANCE

SO

AT25XE021A

DS-25XE021A–061I–9/2017

1 6

9.

Protection Commands and Features

9.1

Write Enable

The Write Enable command is used to set the Write Enable Latch (WEL) bit in the Status Register to a logical “1” state.

The WEL bit must be set before a Byte/Page Program, Erase, Program OTP Security Register, or Write Status Register

command can be executed. This makes the issuance of these commands a two step process, thereby reducing the

chances of a command being accidentally or erroneously executed. If the WEL bit in the Status Register is not set prior to

the issuance of one of these commands, then the command will not be executed.

To issue the Write Enable command, the CS pin must first be asserted and the opcode of 06h must be clocked into the

device. No address bytes need to be clocked into the device, and any data clocked in after the opcode will be ignored.

When the CS pin is deasserted, the WEL bit in the Status Register will be set to a logical “1”. The complete opcode must

be clocked into the device before the CS pin is deasserted, and the CS pin must be deasserted on an even byte

boundary (multiples of eight bits); otherwise, the device will abort the operation and the state of the WEL bit will not

change.

Figure 9-1. Write Enable

CS

0

1

2

3

4

5

6

7

SCK

SI

OPCODE

0

1

0

MSB

HIGH-IMPEDANCE

SO

9.2

Write Disable

The Write Disable command is used to reset the Write Enable Latch (WEL) bit in the Status Register to the logical “0”

state. With the WEL bit reset, all Byte/Page Program, Erase, Program OTP Security Register, and Write Status Register

commands will not be executed. Other conditions can also cause the WEL bit to be reset; for more details, refer to the

WEL bit section of the Status Register description.

To issue the Write Disable command, the CS pin must first be asserted and the opcode of 04h must be clocked into the

device. No address bytes need to be clocked into the device, and any data clocked in after the opcode will be ignored.

When the CS pin is deasserted, the WEL bit in the Status Register will be reset to a logical “0”. The complete opcode

must be clocked into the device before the CS pin is deasserted, and the CS pin must be deasserted on an even byte

boundary (multiples of eight bits); otherwise, the device will abort the operation and the state of the WEL bit will not

change.

AT25XE021A

DS-25XE021A–061I–9/2017

1 7

Figure 9-2. Write Disable

CS

SCK

SI

0

1

2

3

4

5

6

7

OPCODE

0

1

0

MSB

HIGH-IMPEDANCE

SO

9.3

Protect Sector

Every physical sector of the device has a corresponding single-bit Sector Protection Register that is used to control the

software protection of a sector. Upon device power-up or after a device reset, each Sector Protection Register will default

to the logical “1” state indicating that all sectors are protected and cannot be programmed or erased.

Issuing the Protect Sector command to a particular sector address will set the corresponding Sector Protection Register

to the logical “1” state. The following table outlines the two states of the Sector Protection Registers.

Table 9-1. Sector Protection Register Values

Value

Sector Protection Status

0

1

Sector is unprotected and can be programmed and erased.

Sector is protected and cannot be programmed or erased. This is the default state.

Before the Protect Sector command can be issued, the Write Enable command must have been previously issued to set

the WEL bit in the Status Register to a logical “1”. To issue the Protect Sector command, the CS pin must first be

asserted and the opcode of 36h must be clocked into the device followed by three address bytes designating any

address within the sector to be protected. Any additional data clocked into the device will be ignored. When the CS pin is

deasserted, the Sector Protection Register corresponding to the physical sector addressed by A23 - A0 will be set to the

logical “1” state, and the sector itself will then be protected from program and erase operations. In addition, the WEL bit

in the Status Register will be reset back to the logical “0” state.

The complete three address bytes must be clocked into the device before the CS pin is deasserted, and the CS pin must

be deasserted on an even byte boundary (multiples of eight bits); otherwise, the device will abort the operation, the state

of the Sector Protection Register will be unchanged, and the WEL bit in the Status Register will be reset to a logical “0”.

As a safeguard against accidental or erroneous protecting or unprotecting of sectors, the Sector Protection Registers can

themselves be locked from updates by using the SPRL (Sector Protection Registers Locked) bit of the Status Register

(please refer to the Status Register description for more details). If the Sector Protection Registers are locked, then any

attempts to issue the Protect Sector command will be ignored, and the device will reset the WEL bit in the Status

Register back to a logical “0” and return to the idle state once the CS pin has been deasserted.

AT25XE021A

DS-25XE021A–061I–9/2017

1 8

Figure 9-3. Protect Sector

CS

0

1

2

3

4

5

6

7

8

9

10 11 12

26 27 28 29 30 31

SCK

SI

OPCODE

ADDRESS BITS A23-A0

0

1

0

1

0

A

MSB

HIGH-IMPEDANCE

SO

9.4

Unprotect Sector

Issuing the Unprotect Sector command to a particular sector address will reset the corresponding Sector Protection

Register to the logical “0” state (see Table 9-1 for Sector Protection Register values). Every physical sector of the device

has a corresponding single-bit Sector Protection Register that is used to control the software protection of a sector.

Before the Unprotect Sector command can be issued, the Write Enable command must have been previously issued to

set the WEL bit in the Status Register to a logical “1”. To issue the Unprotect Sector command, the CS pin must first be

asserted and the opcode of 39h must be clocked into the device. After the opcode has been clocked in, the three address

bytes designating any address within the sector to be unlocked must be clocked in. Any additional data clocked into the

device after the address bytes will be ignored. When the CS pin is deasserted, the Sector Protection Register

corresponding to the sector addressed by A23 - A0 will be reset to the logical “0” state, and the sector itself will be

unprotected. In addition, the WEL bit in the Status Register will be reset back to the logical “0” state.

The complete three address bytes must be clocked into the device before the CS pin is deasserted, and the CS pin must

be deasserted on an even byte boundary (multiples of eight bits); otherwise, the device will abort the operation, the state

of the Sector Protection Register will be unchanged, and the WEL bit in the Status Register will be reset to a logical “0”.

As a safeguard against accidental or erroneous locking or unlocking of sectors, the Sector Protection Registers can

themselves be locked from updates by using the SPRL (Sector Protection Registers Locked) bit of the Status Register

(please refer to the Status Register description for more details). If the Sector Protection Registers are locked, then any

attempts to issue the Unprotect Sector command will be ignored, and the device will reset the WEL bit in the Status

Register back to a logical “0” and return to the idle state once the CS pin has been deasserted.

Figure 9-4. Unprotect Sector

CS

0

1

2

3

4

5

6

7

8

9

10 11 12

26 27 28 29 30 31

SCK

SI

OPCODE

ADDRESS BITS A23-A0

0

1

0

1

A

MSB

HIGH-IMPEDANCE

SO

9.5

Global Protect/Unprotect

The Global Protect and Global Unprotect features can work in conjunction with the Protect Sector and Unprotect Sector

functions. For example, a system can globally protect the entire memory array and then use the Unprotect Sector

command to individually unprotect certain sectors and individually reprotect them later by using the Protect Sector

command. Likewise, a system can globally unprotect the entire memory array and then individually protect certain

sectors as needed.

AT25XE021A

DS-25XE021A–061I–9/2017

1 9

Performing a Global Protect or Global Unprotect is accomplished by writing a certain combination of data to the Status

Register using the Write Status Register command (see “Write Status Register” section on page 31 for command

execution details). The Write Status Register command is also used to modify the SPRL (Sector Protection Registers

Locked) bit to control hardware and software locking.

To perform a Global Protect, the appropriate WP pin and SPRL conditions must be met, and the system must write a

logical “1” to bits 5, 4, 3, and 2 of the Status Register. Conversely, to perform a Global Unprotect, the same WP and

SPRL conditions must be met but the system must write a logical “0” to bits 5, 4, 3, and 2 of the Status Register. Table 9-

2 details the conditions necessary for a Global Protect or Global Unprotect to be performed.

Table 9-2. Valid SPRL and Global Protect/Unprotect Conditions

New

Write Status

Register Data

Current

SPRL

Value

New

SPRL

Value

WP

State

Bit

7 6 5 4 3 2 1 0

Protection Operation

0 x 0 0 0 0 x x

0 x 0 0 0 1 x x

?

Global Unprotect – all Sector Protection Registers reset to 0

No change to current protection.

Global Protect – all Sector Protection Registers set to 1

0

0 x 1 1 1 0 x x

0 x 1 1 1 1 x x

0

1

0

1

0

1 x 0 0 0 0 x x

1 x 0 0 0 1 x x

?

Global Unprotect – all Sector Protection Registers reset to 0

No change to current protection.

Global Protect – all Sector Protection Registers set to 1

1

1 x 1 1 1 0 x x

1 x 1 1 1 1 x x

No change to the current protection level. All sectors currently protected will remain

protected and all sectors currently unprotected will remain unprotected.

x x x x x x x x

The Sector Protection Registers are hard-locked and cannot be changed when the

WP pin is LOW and the current state of SPRL is 1. Therefore, a Global

Protect/Unprotect will not occur. In addition, the SPRL bit cannot be changed (the

WP pin must be HIGH in order to change SPRL back to a 0).

0 x 0 0 0 0 x x

0 x 0 0 0 1 x x

?

Global Unprotect – all Sector Protection Registers reset to 0

No change to current protection.

Global Protect – all Sector Protection Registers set to 1

0

0 x 1 1 1 0 x x

0 x 1 1 1 1 x x

1 x 0 0 0 0 x x

1 x 0 0 0 1 x x

?

Global Unprotect – all Sector Protection Registers reset to 0

No change to current protection.

Global Protect – all Sector Protection Registers set to 1

1

1 x 1 1 1 0 x x

1 x 1 1 1 1 x x

0 x 0 0 0 0 x x

0 x 0 0 0 1 x x

?

0

No change to the current protection level. All sectors currently protected

will remain protected, and all sectors currently unprotected will remain

unprotected.

0 x 1 1 1 0 x x

0 x 1 1 1 1 x x

The Sector Protection Registers are soft-locked and cannot be changed

when the current state of SPRL is 1. Therefore, a Global

Protect/Unprotect will not occur. However, the SPRL bit can be changed

back to a 0 from a 1 since the WP pin is HIGH. To perform a Global

Protect/Unprotect, the Write Status Register command must be issued

again after the SPRL bit has been changed from a 1 to a 0.

1

1 x 0 0 0 0 x x

1 x 0 0 0 1 x x

?

1

1 x 1 1 1 0 x x

1 x 1 1 1 1 x x

AT25XE021A

DS-25XE021A–061I–9/2017

2 0

Essentially, if the SPRL bit of the Status Register is in the logical “0” state (Sector Protection Registers are not locked),

then writing a 00h to the Status Register will perform a Global Unprotect without changing the state of the SPRL bit.

Similarly, writing a 7Fh to the Status Register will perform a Global Protect and keep the SPRL bit in the logical “0” state.

The SPRL bit can, of course, be changed to a logical “1” by writing an FFh if software-locking or hardware-locking is

desired along with the Global Protect.

If the desire is to only change the SPRL bit without performing a Global Protect or Global Unprotect, then the system can

simply write a 0Fh to the Status Register to change the SPRL bit from a logical “1” to a logical “0” provided the WP pin is

deasserted. Likewise, the system can write an F0h to change the SPRL bit from a logical “0” to a logical “1” without

affecting the current sector protection status (no changes will be made to the Sector Protection Registers).

When writing to the Status Register, bits 5, 4, 3, and 2 will not actually be modified but will be decoded by the device for

the purposes of the Global Protect and Global Unprotect functions. Only bit 7, the SPRL bit, will actually be modified.

Therefore, when reading the Status Register, bits 5, 4, 3, and 2 will not reflect the values written to them but will instead

indicate the status of the WP pin and the sector protection status. Please refer to the “Read Status Register” section and

Table 11-1 on page 25 for details on the Status Register format and what values can be read for bits 5, 4, 3, and 2.

9.6

Read Sector Protection Registers

The Sector Protection Registers can be read to determine the current software protection status of each sector. Reading

the Sector Protection Registers, however, will not determine the status of the WP pin.

To read the Sector Protection Register for a particular sector, the CS pin must first be asserted and the opcode of 3Ch

must be clocked in. Once the opcode has been clocked in, three address bytes designating any address within the sector

must be clocked in. After the last address byte has been clocked in, the device will begin outputting data on the SO pin

during every subsequent clock cycle. The data being output will be a repeating byte of either FFh or 00h to denote the

value of the appropriate Sector Protection Register.

Table 9-3. Read Sector Protection Register – Output Data

Output Data

00h

Sector Protection Register Value

Sector Protection Register value is 0 (sector is unprotected).

Sector Protection Register value is 1 (sector is protected).

FFh

Deasserting the CS pin will terminate the read operation and put the SO pin into a high-impedance state. The CS pin can

be deasserted at any time and does not require that a full byte of data be read.

In addition to reading the individual Sector Protection Registers, the Software Protection Status (SWP) bit in the Status

Register can be read to determine if all, some, or none of the sectors are software protected (refer to the “Status Register

Commands” on page 28 for more details).

Figure 9-5. Read Sector Protection Register

CS

0

1

2

3

4

5

6

7

8

9

10 11 12

29 30 31 32 33 34 35 36 37 38 39 40

SCK

SI

OPCODE

ADDRESS BITS A23-A0

0

1

0

A

MSB

DATA BYTE

HIGH-IMPEDANCE

D

SO

MSB

AT25XE021A

DS-25XE021A–061I–9/2017

2 1

9.7

Protected States and the Write Protect (WP) Pin

The WP pin is not linked to the memory array itself and has no direct effect on the protection status of the memory array.

Instead, the WP pin, in conjunction with the SPRL (Sector Protection Registers Locked) bit in the Status Register, is used

to control the hardware locking mechanism of the device. For hardware locking to be active, two conditions must be met

– the WP pin must be asserted and the SPRL bit must be in the logical “1” state.

When hardware locking is active, the Sector Protection Registers are locked and the SPRL bit itself is also locked.

Therefore, sectors that are protected will be locked in the protected state, and sectors that are unprotected will be locked

in the unprotected state. These states cannot be changed as long as hardware locking is active, so the Protect Sector,

Unprotect Sector, and Write Status Register commands will be ignored. In order to modify the protection status of a

sector, the WP pin must first be deasserted, and the SPRL bit in the Status Register must be reset back to the logical “0”

state using the Write Status Register command. When resetting the SPRL bit back to a logical “0”, it is not possible to

perform a Global Protect or Global Unprotect at the same time since the Sector Protection Registers remain soft-locked

until after the Write Status Register command has been executed.

If the WP pin is permanently connected to GND, then once the SPRL bit is set to a logical “1”, the only way to reset the bit

back to the logical “0” state is to power-cycle or reset the device. This allows a system to power-up with all sectors

software protected but not hardware locked. Therefore, sectors can be unprotected and protected as needed and then

hardware locked at a later time by simply setting the SPRL bit in the Status Register.

When the WP pin is deasserted, or if the WP pin is permanently connected to VCC, the SPRL bit in the Status Register

can still be set to a logical “1” to lock the Sector Protection Registers. This provides a software locking ability to prevent

erroneous Protect Sector or Unprotect Sector commands from being processed. When changing the SPRL bit to a

logical “1” from a logical “0”, it is also possible to perform a Global Protect or Global Unprotect at the same time by writing

the appropriate values into bits 5, 4, 3, and 2 of the Status Register.

Tables 9-4 and 9-5 detail the various protection and locking states of the device.

.

Table 9-4. Sector Protection Register States

Sector Protection Register

n ⁽¹⁾

Sector

n⁽¹⁾

WP

0

1

Unprotected

Protected

X

(Don't Care)

1. “n” represents a sector number

Table 9-5. Hardware and Software Locking

WP

SPRL

Locking

SPRL Change Allowed

Sector Protection Registers

Unlocked and modifiable using the Protect and

Unprotect Sector commands. Global Protect

and Unprotect can also be performed.

0

1

0

Can be modified from 0 to 1

Locked

Locked in current state. Protect and Unprotect

Sector commands will be ignored. Global

Protect and Unprotect cannot be performed.

Hardware

Locked

1

0

1

Unlocked and modifiable using the Protect and

Unprotect Sector commands. Global Protect

and Unprotect can also be performed.

Can be modified from 0 to 1

Can be modified from 1 to 0

Locked in current state. Protect and Unprotect

Sector commands will be ignored. Global

Protect and Unprotect cannot be performed.

Software

Locked

AT25XE021A

DS-25XE021A–061I–9/2017

2 2

10. Security Commands

10.1 Program OTP Security Register

The device contains a specialized OTP (One-Time Programmable) Security Register that can be used for purposes such

as unique device serialization, system-level Electronic Serial Number (ESN) storage, locked key storage, etc. The OTP

Security Register is independent of the main Flash memory array and is comprised of a total of 128 bytes of memory

divided into two portions. The first 64 bytes (byte locations 0 through 63) of the OTP Security Register are allocated as a

one-time user-programmable space. Once these 64 bytes have been programmed, they cannot be erased or

reprogrammed. The remaining 64 bytes of the OTP Security Register (byte locations 64 through 127) are factory

programmed by Adesto and will contain a unique value for each device. The factory programmed data is fixed and

cannot be changed

.

Table 10-1. OTP Security Register

Security Register

Byte Number

0

1

. . .

62

63

64

65

. . .

126

127

One-Time User Programmable

Factory Programmed by Adesto

The user-programmable portion of the OTP Security Register does not need to be erased before it is programmed. In

addition, the Program OTP Security Register command operates on the entire 64-byte user-programmable portion of the

OTP Security Register at one time. Once the user-programmable space has been programmed with any number of

bytes, the user-programmable space cannot be programmed again; therefore, it is not possible to only program the first

two bytes of the register and then program the remaining 62 bytes at a later time.

Before the Program OTP Security Register command can be issued, the Write Enable command must have been

previously issued to set the WEL bit in the Status Register to a logical “1”. To program the OTP Security Register, the CS

pin must first be asserted and an opcode of 9Bh must be clocked into the device followed by the three address bytes

denoting the first byte location of the OTP Security Register to begin programming at. Since the size of the user-

programmable portion of the OTP Security Register is 64 bytes, the upper order address bits do not need to be decoded

by the device. Therefore, address bits A23-A6 will be ignored by the device and their values can be either a logical “1” or

“0”. After the address bytes have been clocked in, data can then be clocked into the device and will be stored in the

internal buffer.

If the starting memory address denoted by A23-A0 does not start at the beginning of the OTP Security Register memory

space (A5-A0 are not all 0), then special circumstances regarding which OTP Security Register locations to be

programmed will apply. In this situation, any data that is sent to the device that goes beyond the end of the 64-byte user-

programmable space will wrap around back to the beginning of the OTP Security Register. For example, if the starting

address denoted by A23-A0 is 00003Eh, and three bytes of data are sent to the device, then the first two bytes of data

will be programmed at OTP Security Register addresses 00003Eh and 00003Fh while the last byte of data will be

programmed at address 000000h. The remaining bytes in the OTP Security Register (addresses 000001h through

00003Dh) will not be programmed and will remain in the erased state (FFh). In addition, if more than 64 bytes of data are

sent to the device, then only the last 64 bytes sent will be latched into the internal buffer.

When the CS pin is deasserted, the device will take the data stored in the internal buffer and program it into the

appropriate OTP Security Register locations based on the starting address specified by A23-A0 and the number of data

bytes sent to the device. If less than 64 bytes of data were sent to the device, then the remaining bytes within the OTP

Security Register will not be programmed and will remain in the erased state (FFh). The programming of the data bytes is

internally self-timed and should take place in a time of t_OTPP

.

AT25XE021A

DS-25XE021A–061I–9/2017

2 3

The three address bytes and at least one complete byte of data must be clocked into the device before the CS pin is

deasserted, and the CS pin must be deasserted on even byte boundaries (multiples of eight bits); otherwise, the device

will abort the operation and the user-programmable portion of the OTP Security Register will not be programmed. The

WEL bit in the Status Register will be reset back to the logical “0” state if the OTP Security Register program cycle aborts

due to an incomplete address being sent, an incomplete byte of data being sent, the CS pin being deasserted on uneven

byte boundaries, or because the user-programmable portion of the OTP Security Register was previously programmed.

While the device is programming the OTP Security Register, the Status Register can be read and will indicate that the

device is busy. For faster throughput, it is recommended that the Status Register be polled rather than waiting the t_OTPP

time to determine if the data bytes have finished programming. At some point before the OTP Security Register

programming completes, the WEL bit in the Status Register will be reset back to the logical “0” state.

If the device is powered-down during the OTP Security Register program cycle, then the contents of the 64-byte user

programmable portion of the OTP Security Register cannot be guaranteed and cannot be programmed again.

The Program OTP Security Register command utilizes the internal 256-buffer for processing. Therefore, the contents of

the buffer will be altered from its previous state when this command is issued.

Figure 10-1. Program OTP Security Register

CS

0

1

2

3

4

5

6

7

8

9

29 30 31 32 33 34 35 36 37 38 39

SCK

SI

OPCODE

ADDRESS BITS A23-A0

DATA IN BYTE 1

DATA IN BYTE n

1

0

1

0

1

A

D

MSB

HIGH-IMPEDANCE

SO

10.2 Read OTP Security Register

The OTP Security Register can be sequentially read in a similar fashion to the Read Array operation up to the maximum

clock frequency specified by f_CLK. To read the OTP Security Register, the CS pin must first be asserted and the opcode

of 77h must be clocked into the device. After the opcode has been clocked in, the three address bytes must be clocked in

to specify the starting address location of the first byte to read within the OTP Security Register. Following the three

address bytes, two dummy bytes must be clocked into the device before data can be output.

After the three address bytes and the dummy bytes have been clocked in, additional clock cycles will result in OTP

Security Register data being output on the SO pin. When the last byte (00007Fh) of the OTP Security Register has been

read, the device will continue reading back at the beginning of the register (000000h). No delays will be incurred when

wrapping around from the end of the register to the beginning of the register.

Deasserting the CS pin will terminate the read operation and put the SO pin into a high-impedance state. The CS pin can

be deasserted at any time and does not require that a full byte of data be read.

AT25XE021A

DS-25XE021A–061I–9/2017

2 4

Figure 10-2. Read OTP Security Register

S

0

1

2

3

4

5

6

7

8

9

10 11 12

29 30 31 32 33 34 35 36

K

OPCODE

ADDRESS BITS A23-A0

DON'T CARE

0

1

0

1

A

X

SI

O

MSB

DATA BYTE 1

HIGH-IMPEDANCE

D

MSB

11. Status Register Commands

11.1 Read Status Register

The Status Register can be read to determine the device's ready/busy status, as well as the status of many other

functions such as Hardware Locking and Software Protection. The Status Register can be read at any time, including

during an internally self-timed program or erase operation.The Status Register consists of two bytes.

To read the Status Register, the CS pin must first be asserted and the opcode of 05h must be clocked into the device.

After the opcode has been clocked in, the device will begin outputting Status Register data on the SO pin during every

subsequent clock cycle. After the last bit (bit 0) of Status Register Byte 2 has been clocked out, the sequence will repeat

itself, starting again with bit 7 of Status Register Byte 1, as long as the CS pin remains asserted and the clock pin is being

pulsed. The data in the Status Register is constantly being updated, so each repeating sequence will output new data.

Deasserting the CS pin will terminate the Read Status Register operation and put the SO pin into a high-impedance

state. The CS pin can be deasserted at any time and does not require that a full byte of data be read.

Table 11-1. Status Register Format

Bit⁽¹⁾

Name

Type ⁽²⁾Description

0

1

0

1

0

1

0

1

Sector Protection Registers are unlocked (default).

7

SPRL

SPM

EPE

Sector Protection Registers Locked

R/W

R

Sector Protection Registers are locked.

Byte/Page Programming Mode (default).

Sequential Programming Mode entered.

Erase or program operation was successful.

Erase or program error detected.

WP is asserted.

6

5

4

Sequential Program Mode Status

Erase/Program Error

R

WPP

Write Protect (WP) Pin Status

R

WP is deasserted.

AT25XE021A

DS-25XE021A–061I–9/2017

2 5

Table 11-1. Status Register Format

Bit⁽¹⁾

Name

Type ⁽²⁾Description

All sectors are software unprotected (all Sector

Protection Registers are 0).

00

01

Some sectors are software protected. Read individual

Sector Protection Registers to determine which

sectors are protected.

3:2

SWP

WEL

Software Protection Status

R

10

11

Reserved for future use.

All sectors are software protected (all Sector

Protection Registers are 1 – default).

0

1

0

1

Device is not write enabled (default).

Device is write enabled.

1

0

Write Enable Latch Status

R

Device is ready.

RDY/BSY Ready/Busy Status

Device is busy with an internal operation.

1. Only bit 7 of the Status Register will be modified when using the Write Status Register command.

2. R/W = Readable and writable

R = Readable only

11.1.1 SPRL Bit

The SPRL bit is used to control whether the Sector Protection Registers can be modified or not. When the SPRL bit is in

the logical “1” state, all Sector Protection Registers are locked and cannot be modified with the Protect Sector and

Unprotect Sector commands (the device will ignore these commands). In addition, the Global Protect and Global

Unprotect features cannot be performed. Any sectors that are presently protected will remain protected, and any sectors

that are presently unprotected will remain unprotected.

When the SPRL bit is in the logical “0” state, all Sector Protection Registers are unlocked and can be modified (the

Protect Sector and Unprotect Sector commands, as well as the Global Protect and Global Unprotect features, will be

processed as normal). The SPRL bit defaults to the logical “0” state after a power-up or a device reset.

The SPRL bit can be modified freely whenever the WP pin is deasserted. However, if the WP pin is asserted, then the

SPRL bit may only be changed from a logical “0” (Sector Protection Registers are unlocked) to a logical “1” (Sector

Protection Registers are locked). In order to reset the SPRL bit back to a logical “0” using the Write Status Register

command, the WP pin will have to first be deasserted.The SPRL bit is the only bit of the Status Register that can be user

modified via the Write Status Register command.

11.1.2 SPM Bit

The SPM bit indicates whether the device is in the Byte/Page Program mode or the Sequential Program Mode. The

default state after power-up or device reset is the Byte/Page Program mode.

11.1.3 EPE Bit

The EPE bit indicates whether the last erase or program operation completed successfully or not. If at least one byte

during the erase or program operation did not erase or program properly, then the EPE bit will be set to the logical “1”

state. The EPE bit will not be set if an erase or program operation aborts for any reason such as an attempt to erase or

program a protected region or if the WEL bit is not set prior to an erase or program operation. The EPE bit will be updated

after every erase and program operation.

AT25XE021A

DS-25XE021A–061I–9/2017

2 6

11.1.4 WPP Bit

The WPP bit can be read to determine if the WP pin has been asserted or not.

11.1.5 SWP Bits

The SWP bits provide feedback on the software protection status for the device. There are three possible combinations

of the SWP bits that indicate whether none, some, or all of the sectors have been protected using the Protect Sector

command or the Global Protect feature. If the SWP bits indicate that some of the sectors have been protected, then the

individual Sector Protection Registers can be read with the Read Sector Protection Registers command to determine

which sectors are in fact protected.

11.1.6 WEL Bit

The WEL bit indicates the current status of the internal Write Enable Latch. When the WEL bit is in the logical “0” state,

the device will not accept any program, erase, Protect Sector, Unprotect Sector, or Write Status Register commands.

The WEL bit defaults to the logical “0” state after a device power-up or reset. In addition, the WEL bit will be reset to the

logical “0” state automatically under the following conditions:



Write Disable operation completes successfully

Write Status Register operation completes successfully or aborts

Protect Sector operation completes successfully or aborts

Unprotect Sector operation completes successfully or aborts

Byte/Page Program operation completes successfully or aborts

Sequential Program Mode reaches highest unprotected memory location

Sequential Program Mode reaches the end of the memory array

Sequential Program Mode aborts ⁽¹⁾

Block Erase operation completes successfully or aborts

Chip Erase operation completes successfully or aborts

Hold condition aborts

If the WEL bit is in the logical “1” state, it will not be reset to a logical “0” if an operation aborts due to an incomplete or

unrecognized opcode being clocked into the device before the CS pin is deasserted. In order for the WEL bit to be reset

when an operation aborts prematurely, the entire opcode for a program, erase, Protect Sector, Unprotect Sector, or Write

Status Register command must have been clocked into the device.

11.1.7 RDY/BSY Bit

The RDY/BSY bit is used to determine whether or not an internal operation, such as a program or erase, is in progress.

To poll the RDY/BSY bit to detect the completion of a program or erase cycle, new Status Register data must be

continually clocked out of the device until the state of the RDY/BSY bit changes from a logical “1” to a logical “0”.Note that

the RDY/BSY bit can be read either from Status Register Byte 1 or from Status Register Byte 2. See also the Active

Status Interrupt command. (11.2)

1. WEL bit will not be reset if Software Reset command is entered.

AT25XE021A

DS-25XE021A–061I–9/2017

2 7

Figure 11-1. Read Status Register

CS

0

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

SCK

SI

OPCODE

0

1

0

1

MSB

STATUS REGISTER BYTE1 STATUS REGISTER BYTE2

HIGH-IMPEDANCE

D

SO

MSB

11.1.8 RSTE Bit

The RSTE bit is used to enable or disable the Reset command. When the RSTE bit is in the Logical 0 state (the default

state after power-up), the Reset command is disabled and any attempts to reset the device using the Reset command

will be ignored. When the RSTE bit is in the Logical 1 state, the Reset command is enabled.

The RSTE bit will retain its state as long as power is applied to the device. Once set to the Logical 1 state, the RSTE bit

will remain in that state until it is modified using the Write Status Register Byte 2 command or until the device has been

power cycled. The Reset command itself will not change the state of the RSTE bit.

Table 11-2. Status Register Format – Byte 2

Bit⁽¹⁾

Name

Type⁽²⁾

Description

Reserved for future use

7

6

5

RES

Reserved for future use

R

0

1

0

1

Reserved for future use

Reset command is disabled (default)

Reset command is enabled

Reserved for future use

4

RSTE

Reset Enabled

R/W

3

2

1

RES

Reserved for future use

R

Reserved for future use

Device is ready

0

RDY/BSY

Ready/Busy Status

R

Device is busy with an internal operation

Note: 1. Only bit 4 of Status Register Byte 2 will be modified when using the Write Status Register Byte 2 command

2. R/W = Readable and Writeable

R = Readable only.

11.2 Active Status Interrupt

To simplify the readout of the RDY/BSY bit, the Active Status Interrupt command (25h) may be used. It is then not

necessary to continuously read the status register, it is sufficient to monitor the value of the SO line. If the SO line is

connected to an interrupt line on the host controller, the host controller may be in sleep mode until the SO line indicates

that the AT25XE021A is ready for the next command.

The RDY/BSY bit can be read at any time, including during an internally self-timed program or erase operation.

AT25XE021A

DS-25XE021A–061I–9/2017

2 8

To enable the Active Status Interrupt command, the CS pin must first be asserted and the opcode of 25h must be

clocked into the device. For SPI Mode3, at least one dummy bit has to be clocked into the device after the last bit of the

opcode has been clocked in. (In most cases, this is most easily done by sending a dummy byte to the device.) The value

of the SI line after the opcode is clocked in is of no significance to the operation. For SPI Mode 0, this dummy bit (dummy

byte) is not required.

The value of RDY/BSY is then output on the SO line, and is continuously updated by the device for as long as the CS pin

remains asserted. Additional clocks on the SCK pin are not required. If the RDY/BSY bit changes from 1 to 0 while the

CS pin is asserted, the SO line will change from 1 to 0. (The RDY/BSY bit cannot change from 0 to 1 during an operation,

so if the SO line already is 0, it will not change.)

Deasserting the CS pin will terminate the Active Status Interrupt operation and put the SO pin into a high-impedance

state. The CS pin can be deasserted at any time and does not require that a full byte of data be read.

Figure 11-2. Active Status Interrupt

CS

0

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15

SCK

SI

23&2'(

0

ꢇ

0

1

0

1

MS B

HIGH-IMPEDANCE

5'<ꢃ%6<

SO

11.3 Write Status Register

The Write Status Register command is used to modify the SPRL bit of the Status Register and/or to perform a Global

Protect or Global Unprotect operation. Before the Write Status Register command can be issued, the Write Enable

command must have been previously issued to set the WEL bit in the Status Register to a logical “1”.

To issue the Write Status Register command, the CS pin must first be asserted and the opcode of 01h must be clocked

into the device followed by one byte of data. The one byte of data consists of the SPRL bit value, a don’t care bit, four

data bits to denote whether a Global Protect or Unprotect should be performed, and two additional don’t care bits (see

Table 11-3). Any additional data bytes that are sent to the device will be ignored. When the CS pin is deasserted, the

SPRL bit in the Status Register will be modified, and the WEL bit in the Status Register will be reset back to a logical “0”.

The values of bits 5, 4, 3, and 2 and the state of the SPRL bit before the Write Status Register command was executed

(the prior state of the SPRL bit) will determine whether or not a Global Protect or Global Unprotect will be perfomed.

Please refer to the “Global Protect/Unprotect” section on page 21 for more details.

The complete one byte of data must be clocked into the device before the CS pin is deasserted; otherwise, the device will

abort the operation, the state of the SPRL bit will not change, no potential Global Protect or Unprotect will be performed,

and the WEL bit in the Status Register will be reset back to the logical “0” state.

If the WP pin is asserted, then the SPRL bit can only be set to a logical “1”. If an attempt is made to reset the SPRL bit to

a logical “0” while the WP pin is asserted, then the Write Status Register command will be ignored, and the WEL bit in the

AT25XE021A

DS-25XE021A–061I–9/2017

2 9

Status Register will be reset back to the logical “0” state. In order to reset the SPRL bit to a logical “0”, the WP pin must

be deasserted.

Table 11-3. Write Status Register Format

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

SPRL

X

Global Protect/Unprotect

X

Figure 11-3. Write Status Register

CS

0

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15

SCK

SI

OPCODE

STATUS REGISTER IN

0

1

D

X

D

X

MSB

HIGH-IMPEDANCE

SO

11.4 Write Status Register Byte 2

The Write Status Register Byte 2 command is used to modify the RSTE. Using the Write Status Register Byte 2

command is the only way to modify the RSTE in the Status Register during normal device operation. Before the Write

Status Register Byte 2 command can be issued, the Write Enable command must have been previously issued to set the

WEL bit in the Status Register to a Logical 1.

To issue the Write Status Register Byte 2 command, the CS pin must first be asserted and then the opcode 31h must be

clocked into the device followed by one byte of data. The one byte of data consists of three don’t-care bits, the RSTE bit

value, and four additional don’t-care bits (see Table 11-4). Any additional data bytes sent to the device will be ignored.

When the CS pin is deasserted, the RSTE bit in the Status Register will be modified, and the WEL bit in the Status

Register will be reset back to a Logical 0.

The complete one byte of data must be clocked into the device before the CS pin is deasserted, and the CS pin must be

deasserted on even byte boundaries (multiples of eight bits); otherwise, the device will abort the operation, the state of

the RSTE bit will not change, and the WEL bit in the Status Register will be reset back to the Logical 0 state.

Table 11-4. Write Status Register Byte 2 Format

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

X

RSTE

X

AT25XE021A

DS-25XE021A–061I–9/2017

3 0

Figure 11-4. Write Status Register Byte 2

CS

0

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15

SCK

SI

Status Register In

Byte 2

Opcode

0

MSB

0

1

0

1

X

MSB

X

D

X

High-impedance

SO

12. Other Commands and Functions

12.1 Read Manufacturer and Device ID

Identification information can be read from the device to enable systems to electronically query and identify the device

while it is in system. The identification method and the command opcode comply with the JEDEC standard for

“Manufacturer and Device ID Read Methodology for SPI Compatible Serial Interface Memory Devices”. The type of

information that can be read from the device includes the JEDEC defined Manufacturer ID, the vendor specific Device ID,

and the vendor specific Extended Device Information.

Since not all Flash devices are capable of operating at very high clock frequencies, applications should be designed to

read the identification information from the devices at a reasonably low clock frequency to ensure all devices used in the

application can be identified properly. Once the identification process is complete, the application can increase the clock

frequency to accommodate specific Flash devices that are capable of operating at the higher clock frequencies.

To read the identification information, the CS pin must first be asserted and the opcode of 9Fh must be clocked into the

device. After the opcode has been clocked in, the device will begin outputting the identification data on the SO pin during

the subsequent clock cycles. The first byte that will be output will be the Manufacturer ID followed by two bytes of Device

ID information. The fourth byte output will be the Extended Device Information String Length, which will be 00h indicating

that no Extended Device Information follows. After the Extended Device Information String Length byte is output, the SO

pin will go into a high-impedance state; therefore, additional clock cycles will have no affect on the SO pin and no data

will be output. As indicated in the JEDEC standard, reading the Extended Device Information String Length and any

subsequent data is optional.Deasserting the CS pin will terminate the Manufacturer and Device ID read operation and

put the SO pin into a high-impedance state. The CS pin can be deasserted at any time and does not require that a full

byte of data be read.

Table 12-1. Manufacturer and Device ID Information

Byte No.

Data Type

Value

1Fh

43h

1

2

3

4

Manufacturer ID

Device ID (Part 1)

Device ID (Part 2)

01h

Extended Device Information String Length

00h

AT25XE021A

DS-25XE021A–061I–9/2017

3 1

Table 12-2. Manufacturer and Device ID Details

Hex

Data Type

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Value

Details

JEDEC Assigned Code

Manufacturer ID

1Fh

43h

01h

JEDEC Code: 0001 1111 (1Fh for Adesto)

0

1

0

1

0

1

Family Code

Density Code

0

Family Code: 010 (AT25F/AT25XExxx series)

Density Code: 00011 (2-Mbit)

Device ID (Part 1)

Device ID (Part 2)

1

Sub Code

0

1

Product Version Code

Sub Code:

000 (Standard series)

Product Version:00001

0

Figure 12-1. Read Manufacturer and Device ID

CS

0

6

7

8

14 15 16

22 23 24

30 31 32

38

SCK

SI

OPCODE

9Fh

HIGH-IMPEDANCE

1Fh

43h

01h

00h

SO

MANUFACTURER ID

DEVICE ID

BYTE1

DEVICE ID

BYTE2

EXTENDED

DEVICE

INFORMATION

STRING LENGTH

Note: Each transition

shown for SI and SO represents one byte (8 bits)

12.2 Deep Power-Down

During normal operation, the device will be placed in the standby mode to consume less power as long as the CS pin

remains deasserted and no internal operation is in progress. The Deep Power-Down command offers the ability to place

the device into an even lower power consumption state called the Deep Power-Down mode.

When the device is in the Deep Power-Down mode, all commands including the Read Status Register command will be

ignored with the exception of the Resume from Deep Power-Down command. Since all commands will be ignored, the

mode can be used as an extra protection mechanism against program and erase operations.

Entering the Deep Power-Down mode is accomplished by simply asserting the CS pin, clocking in the opcode of B9h,

and then deasserting the CS pin. Any additional data clocked into the device after the opcode will be ignored. When the

CS pin is deasserted, the device will enter the Deep Power-Down mode within the maximum time of t_EDPD

.

The complete opcode must be clocked in before the CS pin is deasserted, and the CS pin must be deasserted on an

even byte boundary (multiples of eight bits); otherwise, the device will abort the operation and return to the standby mode

once the CS pin is deasserted. In addition, the device will default to the standby mode after a power-cycle.

The Deep Power-Down command will be ignored if an internally self-timed operation such as a program or erase cycle is

in progress. The Deep Power-Down command must be reissued after the internally self-timed operation has been

completed in order for the device to enter the Deep Power-Down mode.

AT25XE021A

DS-25XE021A–061I–9/2017

3 2

Figure 12-2. Deep Power-Down

CS

t_EDPD

0

1

2

3

4

5

6

7

SCK

SI

OPCODE

1

0

1

0

1

MSB

HIGH-IMPEDANCE

Active Current

SO

I_CC

Standby Mode Current

Deep Power-Down Mode Current

12.3 Resume from Deep Power-Down

In order to exit the Deep Power-Down mode and resume normal device operation, the Resume from Deep Power-Down

command must be issued. The Resume from Deep Power-Down command is the only command that the device will

recognized while in the Deep Power-Down mode.

To resume from the Deep Power-Down mode, the CS pin must first be asserted and opcode of ABh must be clocked into

the device. Any additional data clocked into the device after the opcode will be ignored. When the CS pin is deasserted,

the device will exit the Deep Power-Down mode within the maximum time of t_RDPDand return to the standby mode. After

the device has returned to the standby mode, normal command operations such as Read Array can be resumed.

If the complete opcode is not clocked in before the CS pin is deasserted, or if the CS pin is not deasserted on an even

byte boundary (multiples of eight bits), then the device will abort the operation and return to the Deep Power-Down

mode.

Figure 12-3. Resume from Deep Power-Down

CS

t_RDPD

0

1

2

3

4

5

6

7

SCK

SI

OPCODE

1

0

1

0

1

0

1

MSB

HIGH-IMPEDANCE

Active Current

SO

I

CC

Standby Mode Current

Deep Power-Down Mode Current

AT25XE021A

DS-25XE021A–061I–9/2017

3 3

12.4 Ultra-Deep Power-Down

The Ultra-Deep Power-Down mode allows the device to further reduce its energy consumption compared to the existing

standby and Deep Power-Down modes by shutting down additional internal circuitry. When the device is in the Ultra-

Deep Power-Down mode, all commands including the Status Register Read and Resume from Deep Power-Down

commands will be ignored. Since all commands will be ignored, the mode can be used as an extra protection mechanism

against inadvertent or unintentional program and erase operations. Entering the Ultra-Deep Power-Down mode is

accomplished by simply asserting the CS pin, clocking in the opcode 79h, and then deasserting the CS pin. Any

additional data clocked into the device after the opcode will be ignored. When the CS pin is deasserted, the device will

enter the Ultra-Deep Power-Down mode within the maximum time of t_EUDPD

The complete opcode must be clocked in before the CS pin is deasserted; otherwise, the device will abort the operation

and return to the standby mode once the CS pin is deasserted. In addition, the device will default to the standby mode

after a power cycle. The Ultra-Deep Power-Down command will be ignored if an internally self-timed operation such as a

program or erase cycle is in progress.

Figure 12-4. Ultra-Deep Power-Down

CS

t_EUDPD

0

1

2

3

4

5

6

7

SCK

SI

Opcode

0

MSB

1

0

1

High-impedance

Active Current

SO

I_CC

Standby Mode Current

Ultra-Deep Power-Down Mode Current

12.5 Exit Ultra-Deep Power-Down

To exit from the Ultra-Deep Power-Down mode, any one of three operations can be performed:

Chip Select Toggle

The CS pin must simply be pulsed by asserting the CS pin, waiting the minimum necessary t_CSLUtime, and then

deasserting the CS pin again. To facilitate simple software development, a dummy byte opcode can also be entered

while the CS pin is being pulsed; the dummy byte opcode is simply ignored by the device in this case. After the CS pin

has been deasserted, the device will exit from the Ultra-Deep Power-Down mode and return to the standby mode within

a maximum time of t_XUDPDIf the CS pin is reasserted before the t_XUDPDtime has elapsed in an attempt to start a new

operation, then that operation will be ignored and nothing will be performed.

AT25XE021A

DS-25XE021A–061I–9/2017

3 4

Figure 12-5. Exit Ultra-Deep Power-Down (Chip Select Toggle)

CS

t_CSLU

t_XUDPD

High-impedance

SO

Active Current

I

CC

Standby Mode Current

Ultra-Deep Power-Down Mode Current

Chip Select Low

By asserting the CS pin, waiting the minimum necessary t_XUDPDtime, and then clocking in the first bit of the next Opcode

command cycle. If the first bit of the next command is clocked in before the t_XUDPDtime has elapsed, the device will exit

Ultra Deep Power Down, however the intended operation will be ignored.

Figure 12-6. Exit Ultra-Deep Power-Down (Chip Select Low)

CS

t_XUDPD

High-impedance

SO

Active Current

I

CC

Ultra-Deep Power-Down Mode Current

Power Cycling

The device can also exit the Ultra Deep Power Mode by power cycling the device. The system must wait for the device to

return to the standby mode before normal command operations can be resumed. Upon recovery from Ultra Deep Power

Down all internal registers will be at there Power-On default state.

12.6 Hold

The HOLD pin is used to pause the serial communication with the device without having to stop or reset the clock

sequence. The Hold mode, however, does not have an affect on any internally self-timed operations such as a program

or erase cycle. Therefore, if an erase cycle is in progress, asserting the HOLD pin will not pause the operation, and the

erase cycle will continue until it is finished.

The Hold mode can only be entered while the CS pin is asserted. The Hold mode is activated simply by asserting the

HOLD pin during the SCK low pulse. If the HOLD pin is asserted during the SCK high pulse, then the Hold mode won’t be

started until the beginning of the next SCK low pulse. The device will remain in the Hold mode as long as the HOLD pin

and CS pin are asserted.

While in the Hold mode, the SO pin will be in a high-impedance state. In addition, both the SI pin and the SCK pin will be

ignored. The WP pin, however, can still be asserted or deasserted while in the Hold mode.

AT25XE021A

DS-25XE021A–061I–9/2017

3 5

To end the Hold mode and resume serial communication, the HOLD pin must be deasserted during the SCK low pulse. If

the HOLD pin is deasserted during the SCK high pulse, then the Hold mode won’t end until the beginning of the next SCK

low pulse.

If the CS pin is deasserted while the HOLD pin is still asserted, then any operation that may have been started will be

aborted, and the device will reset the WEL bit in the Status Register back to the logical “0” state.

Figure 12-7. Hold Mode

CS

SCK

HOLD

Hold

12.7 Reset

In some applications, it may be necessary to prematurely terminate a program or erase operation rather than wait the

hundreds of microseconds or milliseconds necessary for the program or erase operation to complete normally. The

Reset command allows a program or erase operation in progress to be ended abruptly and returns the device to an idle

state. Since the need to reset the device is immediate, the Write Enable command does not need to be issued prior to the

Reset command. Therefore, the Reset command operates independently of the state of the WEL bit in the Status

Register.

The Reset command can be executed only if the command has been enabled by setting the Reset Enabled (RSTE) bit in

the Status Register to a Logical 1 using write status register byte 2 command 31h. This command should be entered

before a program command is entered. If the Reset command has not been enabled (the RSTE bit is in the Logical 0

state), then any attempts at executing the Reset command will be ignored.

To perform a Reset, the CS pin must first be asserted, and then the opcode F0h must be clocked into the device. No

address bytes need to be clocked in, but a confirmation byte of D0h must be clocked into the device immediately after the

opcode. Any additional data clocked into the device after the confirmation byte will be ignored. When the CS pin is

deasserted, the program operation currently in progress will be terminated within a time of t_SWRST. Since the program or

erase operation may not complete before the device is reset, the contents of the page being programmed or erased

cannot be guaranteed to be valid.

The Reset command has no effect on the states of the Configuration Register or RSTE bit in the Status Register. Apart

from Sequential Programming, the WEL bit will be reset back to its default state.

The complete opcode and confirmation byte must be clocked into the device before the CS pin is deasserted, and the CS

pin must be deasserted on an even byte boundary (multiples of eight bits); otherwise, no Reset operation will be

performed.

AT25XE021A

DS-25XE021A–061I–9/2017

3 6

Table 12-3. Reset

CS

SCK

SI

0

1

2

3

4

5

6

7

8

9

10 11 12 13 14 15

Opcode

Confirmation Byte In

1

MSB

1

0

1

MSB

1

0

1

0

High-impedance

SO

13. Electrical Specifications

13.1 Absolute Maximum Ratings*

*Notice: Stresses beyond those listed under “Absolute

Maximum Ratings” may cause permanent damage to

the device. This is a stress rating only and functional

operation of the device at these or any other

Temperature under Bias. . . . . . . . -55°C to +125°C

Storage Temperature . . . . . . . . . . -65°C to +150°C

Absolute Maximum V_cc. . . . . . . . . . . . . . . . 3.96V

conditions beyond those indicated in the operational

sections of this specification is not implied. Exposure

to absolute maximum rating conditions for extended

periods may affect device reliability. Voltage extremes

referenced in the “Absolute Maximum Ratings” are

intended to accommodate short duration

undershoot/overshoot conditions and does not imply

or guarantee functional device operation at these

levels for any extended period of time.

All Output Voltages with Respect to Ground

. . . . . . . . . -0.6V to 4.2V (Max V_CCof 3.6V + 0.6V)

All Input Voltages with Respect to Ground

(excluding V_CCpin, including NC pins)

. . . . . . . . . -0.6V to 4.2V (Max V_CCof 3.6V + 0.6V)

13.2 DC and AC Operating Range

AT25XE021A

-40°C to 85°C

1.65V to 3.6V

Operating Temperature (Case)

V_CCPower Supply

Ind.

AT25XE021A

DS-25XE021A–061I–9/2017

3 7

13.3 DC Characteristics

1.65V to 3.6V

Typ

2.3V to 3.6V

Typ

Symbol Parameter

Ultra-Deep Power-

Condition

Min

Max

Min

Max

Units

CS = V_CC.All other

inputs at 0V or V_CC

I_UDPD

0.2

4.5

25

0.6

0.35

5

0.6

µA

Down Current

Deep Power-Down

Current

CS = V_CC.All other

inputs at 0V or V_CC

(1)

I_DPD

15

40

15

40

µA

CS = V_CC.All other

inputs at 0V or V_CC

I_SB

Standby Current

25

(2)(3)

Active Current, Low

Power Read (03h,

0Bh) Operation

f = 1MHz; I_OUT= 0mA

f = 20MHz; I_OUT= 0mA

f = 50MHz; I_OUT= 0mA

3

4.5

3.5

4.2

4.5

mA

I_CC1

3.5

5.25

Active Current,

Read Operation

(2) (3)

I_CC2

f = 85MHz; I_OUT= 0mA

3.5

5.25

4.2

5.25

mA

Active Current,

Program Operation

(2)(3)

I_CC3

I_CC4

I_LI

CS = V_CC

9

8

10.5

11

1

9

8

10.5

11

1

mA

µA

V

Active Current,

Erase Operation

All inputs at CMOS

levels

Input Load Current

Output Leakage

Current

All inputs at CMOS

levels

I_LO

1

V_CC

0.2

x

V_CC

0.3

x

V_IL

Input Low Voltage

Input High Voltage

V_IH

V_CCx 0.8

V_CCx 0.7

V

V_OL

Output Low Voltage I_OL= 100µA

0.2

0.4

Output High

I_OH= -100µA

Voltage

V_CC

0.2V

-

V_CC

0.2V

-

V_OH

V

1. Max. specification is 20µA @ 85°C.

2. Typical values measured at 1.8V @ 25°C for the 1.65V to 3.6V range.

3. Typical values measured at 3.0V @ 25°C for the 2.3V to 3.6V range.

AT25XE021A

DS-25XE021A–061I–9/2017

3 8

13.4 AC Characteristics - Maximum Clock Frequencies

1.65V to 3.6V

2.3V to 3.6V

Typ

Symbol

Parameter

Min

Typ

Max

Min

Max

Units

Maximum Clock Frequency for All Operations

(including 0Bh opcode)

f_CLK

70

MHz

Maximum Clock Frequency for 03h Opcode

(Read Array – Low Frequency)

f_RDLF

25

40

25

40

MHz

Maximum Clock Frequency for 3B Opcode

f_RDDO

13.5 AC Characteristics – All Other Parameters

1.65V to 3.6V

Typ

2.3V to 3.6V

Typ

Symbol

t_CLKH

Parameter

Min

4.5

4

Max

Min

4.5

4

Max

Units

ns

Clock High Time

t_CLKL

Clock Low Time

ns

(1)

t_CLKR

Clock Rise Time, Peak-to-Peak (Slew Rate)

Clock Fall Time, Peak-to-Peak (Slew Rate)

Chip Select High Time

0.1

35

6

0.1

25

5

V/ns

ns

(1)

t_CLKF

t_CSH

t_CSLS

t_CSLH

t_CSHS

t_CSHH

t_DS

Chip Select Low Setup Time (relative to Clock)

Chip Select Low Hold Time (relative to Clock)

Chip Select High Setup Time (relative to Clock)

Chip Select High Hold Time (relative to Clock)

Data In Setup Time

ns

6

5

ns

6

5

ns

6

5

ns

2

ns

t_DH

Data In Hold Time

1

ns

(1)

t_DIS

Output Disable Time

8

6

ns

t_V

Output Valid Time

7.5

ns

t_OH

Output Hold Time

0

6

0

5

ns

t_HLS

t_HLH

t_HHS

t_HHH

HOLD Low Setup Time (relative to Clock)

HOLD Low Hold Time (relative to Clock)

HOLD High Setup Time (relative to Clock)

HOLD High Hold Time (relative to Clock)

HOLD Low to Output High-Z

HOLD High to Output Low-Z

Write Protect Setup Time

ns

(1)

t_HLQZ

7

6

ns

(1)

t_HHQX

ns

(1)(1)

t_WPS

20

ns

(1)(1)

t_WPH

Write Protect Hold Time

100

ns

(1)

t_EDPD

Chip Select High to Deep Power-Down

3

µs

AT25XE021A

DS-25XE021A–061I–9/2017

3 9

13.5 AC Characteristics – All Other Parameters

1.65V to 3.6V

Typ

2.3V to 3.6V

Typ

Symbol

Parameter

Min

Max

3

Min

Max

3

Units

µs

(1)

t_EUDPD

Chip Select High to Ultra Deep Power-Down

Software Reset Time

t_SWRST

t_CSLU

60

µs

Minimum Chip Select Low to Exit Ultra Deep

Power-Down

20

70

20

70

ns

t_XUDPD

Exit Ultra Deep Power-Down Time

Chip Select High to Standby Mode

µs

(1)

t_RDPD

8

Notes: 1. Not 100% tested (value guaranteed by design and characterization).

13.6 Program and Erase Characteristics

1.65V-3.6V

2.3V-3.6V

Symbol

Parameter

Min

Typ

2

Max

Min

Typ

2

Max

Units

ms

(1)

t_PP

Page Program Time

Byte Program Time

Page Erase Time

256 Bytes

5

3.8

t_BP

t_PE

8

µs

256 Bytes

4 Kbytes

6

20

100

600

1200

4.8

6

15

60

ms

45

360

720

2.4

400

45

360

720

2.4

400

(1)

t_BLKE

Block Erase Time

32 Kbytes

64 Kbytes

500

1000

4.0

ms

(1)(2)

t_CHPE

Chip Erase Time

sec

µs

(1)

t_OTPP

OTP Security Register Program Time

Write Status Register Time

950

200

950

200

t_WRSR

ns

Note: 1. Maximum values indicate worst-case performance after 100,000 erase/program cycles.

2. Not 100% tested (value guaranteed by design and characterization).

AT25XE021A

DS-25XE021A–061I–9/2017

4 0

14. Power-On/Reset State

When power is first applied to the device, or when recovering from a reset condition, the output pin (SO) will be in a high

impedance state, and a high-to-low transition on the CSB pin will be required to start a valid instruction. The SPI mode

(Mode 3 or Mode 0) will be automatically selected on every falling edge of CSB by sampling the inactive clock state.

14.1 Power-Up/Power-Down Voltage and Timing Requirements

During power-up, the device must not be READ for at least the minimum t_VCSLtime after the supply voltage reaches the

minimum V_PORlevel (V_PORmin). While the device is being powered-up, the internal Power-On Reset (POR) circuitry

keeps the device in a reset mode until the supply voltage rises above the minimum V_cc. During this time, all operations

are disabled and the device will not respond to any commands.

If the first operation to the device after power-up will be a program or erase operation, then the operation cannot be

started until the supply voltage reaches the minimum V_CClevel and an internal device delay has elapsed. This delay will

be a maximum time of t_PUW. After the t_PUWtime, the device will be in the standby mode if CSB is at logic high or active

mode if CSB is at logic low. For the case of Power-down then Power-up operation, or if a power interruption occurs (such

that VCC drops below V_PORmax), the V_ccof the Flash device must be maintained below V_PWDfor at least the minimum

specified T_PWDtime. This is to ensure the Flash device will reset properly after a power interruption.

Table 14-1. Voltage and Timing Requirements for Power-Up/Power-Down

Symbol

Parameter

Min

Max

Units

V

(1)

V_PWD

V_CCfor device initialization

1.0

(1)

t_PWD

Minimum duration for device initialization

Minimum V_CCto chip select low time for Read command

V_CCrise time

300

70

µs

t_VCSL

µs

(1)

t_VR

1

500000

µs/V

V

V_POR

t_PUW

Power on reset voltage

1.45

1.6

3

Power up delay time before Program or Erase is allowed

ms

1. Not 100% tested (value guaranteed by design and characterization).

Figure 14-1. Power-Up Timing

VCC

V

_PORmax

t_PUW

Full Operation Permitted

Read Operation

Permitted

t_VCSL

Max V_PWD

t_PWD

t_VR

Time

AT25XE021A

DS-25XE021A–061I–9/2017

4 1

14.2 Input Test Waveforms and Measurement Levels

0.9V_CC

AC

DRIVING

LEVELS

V_CC/2

MEASUREMENT

LEVEL

0.1V_CC

t_R, t_F< 2 ns (10% to 90%)

14.3 Output Test Load

Device

Under

Test

30pF

15. AC Waveforms

Figure 15-1. Serial Input Timing

t_CSH

CS

SCK

SI

t_CSLS

t_CSLH

t_CLKL

t_CSHH

t_CLKH

t_CSHS

t_DS

t_DH

MSB

LSB

MSB

HIGH-IMPEDANCE

SO

Figure 15-2. Serial Output Timing

CS

t_CLKH

t_CLKL

t_DIS

SCK

SI

t_OH

t_V

SO

AT25XE021A

DS-25XE021A–061I–9/2017

4 2

Figure 15-3. WP Timing for Write Status Register Command When BPL = 1

CS

t_WPS

t_WPH

WP

SCK

SI

0

X

MSB

MSB OF

WRITE STATUS REGISTER

OPCODE

LSB OF

WRITE STATUS REGISTER

DATA BYTE

MSB OF

NEXT OPCODE

HIGH-IMPEDANCE

SO

Figure 15-4. HOLD Timing – Serial Input

CS

SCK

t_HHH

t_HLS

t_HLH

t_HHS

HOLD

SI

HIGH-IMPEDANCE

SO

Figure 15-5. HOLD Timing – Serial Output

CS

SCK

t_HHH

t_HLS

t_HLH

t_HHS

HOLD

SI

t_HLQZ

SO

t_HHQX

AT25XE021A

DS-25XE021A–061I–9/2017

4 3

16. Ordering Information

16.1 Ordering Code Detail

A T 2 5 X E 0 2 1 A – S S H N – B

Designator

Shipping Carrier Option

B = Bulk (tubes)

T = Tape and reel

Y = Tray

Product Family

Operating Voltage

N

= 1.65V to 3.6V

Device Density

Device Grade

02 = 2-megabit

H = Green, NiPdAu lead ﬁnish, industrial

temperature range (-40°C to +85°C)

U = Green, Matte Sn or Sn alloy,

Industrial temperature range

(–40°C to +85°C)

Interface

1 = Serial

Package Option

MA = 8-pad, 2 x 3 x 0.6 mm UDFN

M = 8-pad, 5 x 6 x 0.6 mm UDFN

SS = 8-lead, 0.150" wide SOIC

XM = 8-lead TSSOP

Device Revision

U = 8-ball WLCSP

Max. Freq.

Ordering Code⁽¹⁾

Package

Lead Finish

Operating Voltage

(MHz)

Operation Range

AT25XE021A-SSHN-B

AT25XE021A-SSHN-T

8S1

AT25XE021A-MHN-Y

AT25XE021A-MHN-T

AT25XE021A-MAHN-T

AT25XE021A-XMHN-B

AT25XE021A-XMHN-T

AT25XE021A-UUN-T⁽²⁾

8MA1

8MA3

8X

Industrial

NiPdAu

1.65V to 3.6V

70

(-40°C to +85°C)

CS2- 8A

Note:

1. The shipping carrier option code is not marked on the devices.

2. Contact info@adestotech.com for manufacturing flow and availability.

Package Type

8S1

8-lead, 0.150" Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC)

8MA1

8-pad, 5 x 6 x 0.6mm, Thermally Enhanced Plastic Ultra Thin Dual Flat No-lead (UDFN)

8MA3

8X

8-pad, 2 x 3 x 0.6mm, Thermally Enhanced Plastic Ultra Thin Dual Flat No Lead Package (UDFN)

8-lead, Thin Shrink Small Outline Package

CS2-8A

8-ball, Wafer level Chip Scale Package

AT25XE021A

DS-25XE021A–061I–9/2017

4 4

17. Packaging Information

17.1 8S1 – JEDEC SOIC

C

1

E

E1

L

N

Ø

TOP VIIEEWW

END VIEW

e

b

COMMON DIMENSIONS

(Unit of Measure = mm)

A

MIN

1.35

0.10

MAX

1.75

0.25

NOM

NOTE

SYMBOL

A1

A

–

A1

b

0.31

0.17

4.80

3.81

5.79

–

0.51

0.25

5.05

3.99

6.20

C

D

E1

E

e

–

D

–

SIDDEE VVIIEEWW

1.27 BSC

L

0.40

0°

–

1.27

8°

Notes: This drawing is for general information only.

Refer to JEDEC Drawing MS-012, Variation AA

for proper dimensions, tolerances, datums, etc.

Ø

8/20/14

TITLE

GPC

DRAWING NO.

REV.

8S1, 8-lead (0.150”Wide Body), Plastic Gull

Wing Small Outline (JEDEC SOIC)

SWB

8S1

G

Package Drawing Contact:

contact@adestotech.com

AT25XE021A

DS-25XE021A–061I–9/2017

4 5

17.2 8MA1 – 5 x 6 UDFN

E

C

Pin 1 ID

SIDE VIEW

D

y

TOP VIEW

A1

A

K

E2

Option A

0.45

Pin #1

8

1

2

3

Pin #1 Notch

(0.20 R)

Chamfer

(C 0.35)

COMMON DIMENSIONS

(Unit of Measure = mm)

(Option B)

MIN

MAX

NOM

NOTE

SYMBOL

7

A

0.45

0.55

0.60

e

D2

A1

b

0.00

0.35

0.02

0.40

0.152 REF

5.00

4.00

6.00

3.40

1.27

0.60

–

0.05

0.48

6

C

D

D2

E

4.90

3.80

5.90

3.20

5.10

4.20

6.10

3.60

5

4

b

BOTTOM VIEW

L

E2

e

L

0.50

0.00

0.20

0.75

0.08

–

y

K

–

4/15/08

GPC

YFG

DRAWING NO.

TITLE

REV.

Package Drawing Contact: 8MA1, 8-pad (5 x 6 x 0.6 mm Body), Thermally

8MA1

D

contact@adestotech.com

Enhanced Plastic Ultra Thin Dual Flat No Lead

Package (UDFN)

AT25XE021A

DS-25XE021A–061I–9/2017

4 6

17.3 8MA3 – 2 x 3 UDFN

5

8

7

6

5

D2

Chamfer or half-circle

notch for Pin 1 indicator.

PIN 1 ID

L3

L

L1

4

1

2

3

1

4

D

COMMON DIMENSIONS

(Unit of Measure = mm)

eee

MIN

0.45

0.00

MAX

0.60

0.05

NOM

SYMBOL

A

A1

A3

b

0.150 REF

0.20

1.50

0.10

0.30

1.70

0.30

0.50

D

2.00 BSC

1.60

D2

E

3.00 BSC

0.20

Notes: 1. All dimensions are in mm. Angles in degrees.

E2

e

2. Bilateral coplanarity zone applies to the exposed heat

sink slug as well as the terminals.

0.50 BSC

0.45

L

0.40

0.00

0.30

–

L1

L3

eee

0.10

0.50

0.08

–

8/26/14

GPC

DRAWING NO.

REV.

TITLE

8MA3, 8-pad, 2 x 3 x 0.6 mm Body, 0.5 mm Pitch,

1.6 x 0.2 mm Exposed Pad, Saw Singulated

Thermally Enhanced Plastic Ultra Thin Dual

Flat No Lead Package (UDFN/USON)

Package Drawing Contact:

®

YCQ

8MA3

GT

contact@adestotech.com

AT25XE021A

DS-25XE021A–061I–9/2017

4 7

17.4 8X-TSSOP

C

1

Pin 1 indicator

this corner

E1

E

L1

H

N

L

Top View

End View

A

b

A1

COMMON DIMENSIONS

(Unit of Measure = mm)

e

A2

MIN

-

MAX

1.20

0.15

1.05

3.10

NOM

NOTE

2, 5

SYMBOL

D

A

-

Side View

A1

A2

D

0.05

0.80

2.90

-

1.00

Notes: 1. This drawing is for general information only. Refer to JEDEC

Drawing MO-153, Variation AA, for proper dimensions,

tolerances, datums, etc.

3.00

2. Dimension D does not include mold Flash, protrusions or gate

burrs. Mold Flash, protrusions and gate burrs shall not exceed

0.15mm (0.006in) per side.

3. Dimension E1 does not include inter-lead Flash or protrusions.

Inter-lead Flash and protrusions shall not exceed 0.25mm

(0.010in) per side.

E

6.40 BSC

4.40

E1

b

4.30

0.19

4.50

0.30

3, 5

4

–

e

0.65 BSC

0.60

4. Dimension b does not include Dambar protrusion. Allowable

Dambar protrusion shall be 0.08mm total in excess of the b

dimension at maximum material condition. Dambar cannot be

located on the lower radius of the foot. Minimum space between

protrusion and adjacent lead is 0.07mm.

L

0.45

0.09

0.75

0.20

L1

C

1.00 REF

-

5. Dimension D and E1 to be determined at Datum Plane H.

12/8/11

TITLE

GPC

TNR

DRAWING NO.

REV.

8X, 8-lead 4.4mm Body, Plastic Thin

Shrink Small Outline Package (TSSOP)

8X

E

Package Drawing Contact:

contact@adestotech.com

AT25XE021A

DS-25XE021A–061I–9/2017

4 8

17.5 CS2-8A - 8 Ball WLCSPl

h

d

d2

D

g

E

f

e

k

j

A2

A

A1

COMMON DIMENSIONS

(Unit of Measure = mm)

MIN

MAX

0.35

TYP

NOTE

SYMBOL

A

A1

A2

E

* Dimensions are NOT to scale.

0.08

0.25

Pin Assignment Matrix

A

B

C

D

E

1.355 0.05

0.4

e

V_CC

SCK

1

2

3

HOLD

d

0.7

GND

SI

d2

D

f

0.35

SO

WP

CS

1.575 0.05

0.8

g

0.44

h

j

0.28

0.2

k

0.4

6/13/17

TITLE

DRAWING NO.

REV.

GPC

DEC

®

CS2-8A, 8-ball Wafer Level Chip Scale

Package, WLCSP

CS2-8A

0A

Package Drawing Contact:

contact@adestotech.com

AT25XE021A

DS-25XE021A–061I–9/2017

4 9

18. Revision History

Revision Level – Release Date

A – October 2014

History

Initial release.

B – October 2014

Updated document status to Preliminary.

Added I_DPDspecification footnote.

C – February 2015

Updated AC and DC characteristics. Expanded explanation of Power up/Power down

(Section 14).

D – May 2015

Updated I_DPDand I_SBspecification conditions. Updated document status from Preliminary to

Complete.

E – November 2015

F – September 2016

G – February 2017

Added WLCSP package. Added U device grade.

Added patent information.Updated description in Section 8.4 (Page Erase).

Added clarification of Absolute Maximum Ratings. Added footnote and updated WLCSP

references.

H - June 2017

I - September 2017

Updated page program time specification.

AT25XE021A

DS-25XE021A–061I–9/2017

5 0

Corporate Office

California | USA

Adesto Headquarters

3600 Peterson Way

Santa Clara, CA 95054

Phone: (+1) 408.400.0578

Email: contact@adestotech.com

®

Adesto , the Adesto logo, CBRAM , and DataFlash are registered trademarks or trademarks of Adesto Technologies. All other marks are the property of their respective

owners. Adesto products in this datasheet are covered by certain Adesto patents registered in the United States and potentially other countries. Please refer to

http://www.adestotech.com/patents for details.

Disclaimer: Adesto Technologies Corporation makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in Adesto's Terms

and Conditions located on the Company's web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications

detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Adesto are granted by the

Company in connection with the sale of Adesto products, expressly or by implication. Adesto's products are not authorized for use as critical components in life support devices or systems.


型号：	AT25XE021A
厂家：	Dialog Semiconductor
描述：	2-Mbit, 1.65V Minimum SPI Serial Flash Memory with Dual-I/O Support
文件：	总52页 (文件大小：1347K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

AT25XE021A [DIALOG]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E