E15C5H2F-80.000M [ECLIPTEK]
CRYSTAL OSCILLATOR, CLOCK, 80MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN;
| 型号： | E15C5H2F-80.000M |
| 厂家： | 
Ecliptek |
| 描述： | CRYSTAL OSCILLATOR, CLOCK, 80MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN 机械 输出元件 振荡器 |
| 文件： | 总5页 (文件大小：200K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
RoHS
Pb
E15C5H2F-80.000M
E15C5 H 2 F -80.000M
Series
Nominal Frequency
RoHS Compliant (Pb-free) 2.5V 6 Pad 3.2mm x 5mm
Ceramic SMD LVPECL Oscillator
80.000MHz
Logic Control / Additional Output
Tri-State and Complementary Output
Frequency Tolerance/Stability
±50ppm Maximum over -40°C to +85°C
Duty Cycle
50 ±5(%)
ELECTRICAL SPECIFICATIONS
Nominal Frequency
80.000MHz
Frequency Tolerance/Stability
±50ppm Maximum over -40°C to +85°C (Inclusive of all conditions: Calibration Tolerance (at 25°C),
Frequency Stability over the Operating Temperature Range, Supply Voltage Change, Output Load Change,
1st Year Aging at 25°C, and Vibration)
Supply Voltage
+2.5Vdc ±5%
Input Current
75mA Maximum
Output Voltage Logic High (Voh)
Output Voltage Logic Low (Vol)
Rise/Fall Time
Vcc-1.025Vdc Minimum from 0°C to +85°C, Vcc-1.085Vdc Minimum from -40°C to 0°C
Vcc-1.405Vdc Maximum from 0°C to +85°C, Vcc-1.305Vdc Maximum from -40°C to 0°C
300pSec Typical, 700pSec Maximum (Measured at 20% to 80% of Waveform)
50 ±5(%) (Measured at 50% of Waveform)
Duty Cycle
Load Drive Capability
Output Logic Type
Phase Noise
50 Ohms into Vcc-2.0Vdc
LVPECL
-60dBc/Hz at 10Hz Offset, -95dBc/Hz at 100Hz Offset, -125dBc/Hz at 1kHz Offset, -143dBc/Hz at 10kHz
Offset, -145dBc/Hz at 100kHz Offset, -145dBc/Hz at 1MHz Offset, -146dBc/Hz at 10MHz Offset (All Values
are Typical, Fo=156.250MHz)
Logic Control / Additional Output
Tri-State Input Voltage (Vih and Vil)
Tri-State and Complementary Output
Vih of 70% of Vcc Minimum or No Connect to Enable Output and Complementary Output, Vil of 30% of Vcc
Maximum to Disable High Impedance Output and Complementary Output
Standby Current
30µA Maximum (Without Load)
0.4pSec Typical, 1pSec Maximum (Fj=12kHz to 20MHz)
10mSec Maximum
RMS Phase Jitter
Start Up Time
Storage Temperature Range
-55°C to +125°C
ENVIRONMENTAL & MECHANICAL SPECIFICATIONS
ESD Susceptibility
MIL-STD-883, Method 3015, Class 1, HBM: 1500V
MIL-STD-883, Method 1014, Condition A
UL94-V0
Fine Leak Test
Flammability
Gross Leak Test
Mechanical Shock
Moisture Resistance
Moisture Sensitivity
Resistance to Soldering Heat
Resistance to Solvents
Solderability
MIL-STD-883, Method 1014, Condition C
MIL-STD-883, Method 2002, Condition B
MIL-STD-883, Method 1004
J-STD-020, MSL 1
MIL-STD-202, Method 210, Condition K
MIL-STD-202, Method 215
MIL-STD-883, Method 2003
Temperature Cycling
Vibration
MIL-STD-883, Method 1010, Condition B
MIL-STD-883, Method 2007, Condition A
www.ecliptek.com | Specification Subject to Change Without Notice | Rev B 2/16/2010 | Page 1 of 5
E15C5H2F-80.000M
MECHANICAL DIMENSIONS (all dimensions in millimeters)
PIN CONNECTION
1
2
3
4
5
6
Tri-State
3.20
1.30
1.20
±0.15
No Connect
±0.15
MAX
Case/Ground
Output
6
5
4
1
2
3
Complementary Output
Supply Voltage
2.54
±0.15
5.00
±0.15
LINE MARKING
1
E80.000
E=Ecliptek Designator
2
XXYZZ
XX=Ecliptek Manufacturing
Code
Y=Last Digit of the Year
ZZ=Week of the Year
0.64
±0.10
1.27
±0.15
1.00
±0.15
Suggested Solder Pad Layout
All Dimensions in Millimeters
1.40 (X6)
1.00 (X6)
0.27 (X4)
Solder Land
0.80 (X2)
(X6)
All Tolerances are ±0.1
www.ecliptek.com | Specification Subject to Change Without Notice | Rev B 2/16/2010 | Page 2 of 5
E15C5H2F-80.000M
Test Circuit for Tri-State and Complementary Output
50 Ohms
Frequency
Counter
Oscilloscope
Pin Connections
1 Tri-State
2 No Connect
3 Ground
4 Output
Power
Supply
Probe 2 Probe 1
(Note 2) (Note 2)
5 Complementary Output
Supply
6 Supply Voltage (VDD
)
Voltage
(VDD
)
Output
50 Ohms
Current
Meter
Complementary
Output
0.01µF
(Note 1)
0.1µF
(Note 1)
Switch
Ground
Power
Supply
Voltage
Meter
Power
Supply
Power
Supply
Tri-State
No
Connect
Note 1: An external 0.01µF ceramic bypass capacitor in parallel with a 0.1µF high frequency ceramic bypass capacitor close (less than 2mm)
to the package ground and supply voltage pin is required.
Note 2: A low capacitance (<12pF), 10X attenuation factor, high impedance (>10Mohms), and high bandwidth (>500MHz) passive probe is
recommended.
Note 3: Test circuit PCB traces need to be designed for a characteristic line impedance of 50 ohms.
www.ecliptek.com | Specification Subject to Change Without Notice | Rev B 2/16/2010 | Page 3 of 5
E15C5H2F-80.000M
Recommended Solder Reflow Methods
Critical Zone
TL to TP
TP
Ramp-up
Ramp-down
TL
TS Max
TS Min
tL
tP
tSPreheat
t 25°C to Peak
Time (t)
High Temperature Infrared/Convection
TS MAX to TL (Ramp-up Rate)
3°C/second Maximum
Preheat
- Temperature Minimum (TS MIN)
- Temperature Typical (TS TYP)
- Temperature Maximum (TS MAX)
- Time (tS MIN)
150°C
175°C
200°C
60 - 180 Seconds
Ramp-up Rate (TL to TP)
3°C/second Maximum
Time Maintained Above:
- Temperature (TL)
- Time (tL)
217°C
60 - 150 Seconds
Peak Temperature (TP)
260°C Maximum for 10 Seconds Maximum
250°C +0/-5°C
Target Peak Temperature (TP Target)
Time within 5°C of actual peak (tp)
Ramp-down Rate
20 - 40 seconds
6°C/second Maximum
8 minutes Maximum
Level 1
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
www.ecliptek.com | Specification Subject to Change Without Notice | Rev B 2/16/2010 | Page 4 of 5
E15C5H2F-80.000M
Recommended Solder Reflow Methods
Critical Zone
TL to TP
TP
Ramp-up
Ramp-down
TL
TS Max
TS Min
tL
tP
tSPreheat
t 25°C to Peak
Time (t)
Low Temperature Infrared/Convection 240°C
TS MAX to TL (Ramp-up Rate)
5°C/second Maximum
Preheat
- Temperature Minimum (TS MIN)
- Temperature Typical (TS TYP)
- Temperature Maximum (TS MAX)
- Time (tS MIN)
N/A
150°C
N/A
60 - 120 Seconds
Ramp-up Rate (TL to TP)
5°C/second Maximum
Time Maintained Above:
- Temperature (TL)
- Time (tL)
150°C
200 Seconds Maximum
Peak Temperature (TP)
240°C Maximum
Target Peak Temperature (TP Target)
Time within 5°C of actual peak (tp)
Ramp-down Rate
240°C Maximum 1 Time / 230°C Maximum 2 Times
10 seconds Maximum 2 Times / 80 seconds Maximum 1 Time
5°C/second Maximum
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
N/A
Level 1
Low Temperature Manual Soldering
185°C Maximum for 10 seconds Maximum, 2 times Maximum.
High Temperature Manual Soldering
260°C Maximum for 5 seconds Maximum, 2 times Maximum.
www.ecliptek.com | Specification Subject to Change Without Notice | Rev B 2/16/2010 | Page 5 of 5
相关型号：
E15C5H2F-80.000MTR
CRYSTAL OSCILLATOR, CLOCK, 80MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5H2F-80M
CRYSTAL OSCILLATOR, CLOCK, 80MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5H2F-90MTR
CRYSTAL OSCILLATOR, CLOCK, 90MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5J2F-100M
CRYSTAL OSCILLATOR, CLOCK, 100MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5J2F-100MTR
CRYSTAL OSCILLATOR, CLOCK, 100MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5J2F-120M
CRYSTAL OSCILLATOR, CLOCK, 120MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5J2F-120MTR
CRYSTAL OSCILLATOR, CLOCK, 120MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5J2F-122.888MTR
CRYSTAL OSCILLATOR, CLOCK, 122.888MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5J2F-124.400MTR
CRYSTAL OSCILLATOR, CLOCK, 124.4MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5J2F-124.4M
CRYSTAL OSCILLATOR, CLOCK, 124.4MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5J2F-124.4MTR
CRYSTAL OSCILLATOR, CLOCK, 124.4MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
©2020 ICPDF网 联系我们和版权申明