EP1400SJETPDL-4.602273MTR [ECLIPTEK]

CRYSTAL OSCILLATOR, CLOCK, TTL OUTPUT;


型号：	EP1400SJETPDL-4.602273MTR
厂家：	Ecliptek
描述：	CRYSTAL OSCILLATOR, CLOCK, TTL OUTPUT 输出元件
文件：	总9页 (文件大小：939K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Ecliptek | EP14 Series Oscillator

http://www.ecliptek.com/oscillators/EP14/

Log On | 714-433-1200 | Email Customer Support

Home

Products

Quick Quote

My Parts List

Site Map

EP14 Series Oscillator

Quartz Crystal Clock Oscillators XO (SPXO) HCMOS/TTL (CMOS) 5.0Vdc J-Lead 9.8mm x 14.0mm Plastic Surface Mount (SMD)

2011/65 +

168 SVHC

2015/863

Revision F 03/25/2014

Electrical Specifications

Nominal Frequency

1.000MHz to 125.000MHz

Some frequencies within this range may not be available.

Frequency Tolerance/Stability

(Inclusive of all conditions: Calibration Tolerance at 25°C, Frequency

Stability over the Operating Temperature Range, Supply Voltage

Change, Output Load Change, First Year Aging at 25°C, Shock, and

Vibration)

±100ppm Maximum

±50ppm Maximum

Operating Temperature Range

-20°C to +70°C

-40°C to +85°C

Supply Voltage (V

Input Current

)

5.0V

±10%

45mA Maximum (Unloaded)

Output Voltage Logic High (V

)

2.4V

Minimum with TTL Load, V -0.4V

Minimum with HCMOS

Load, IOH = -16mA

Output Voltage Logic Low (V

Duty Cycle

)

0.4V

Maximum, IOL = +16mA

Measured at 1.4V

with TTL Load; Measured at 50% of waveform

with HCMOS Load

50 ±10(%)

50 ±5(%) (Not available with Output Logic Type of TTL over Nominal

Frequency of 27.000001MHz to 125MHz; Not available with Output

Logic Type of CMOS over Nominal Frequency range of 50.000001MHz

to 125MHz)

Rise Time/Fall Time

Load Drive Capability

4nSec Maximum (Measured at 20% to 80% of waveform) at Output

Logic Type of CMOS

4nSec Maximum (Measured at 0.8V

to 2.0V ) at Output Logic Type

of TTL

50pF HCMOS Load Maximum over Nominal Frequency of 1MHz to

50MHz at Output Logic Type of CMOS

15pF HCMOS Load Maximum over Nominal Frequency of

50.000001MHz to 125MHz at Output Logic Type of CMOS

10TTL Load Maximum over Nominal Frequency of 1MHz to 40MHz at

Output Logic Type of TTL

5TTL Load Maximum over Nominal Frequency of 40.000001MHz to

125MHz at Output Logic Type of TTL

Output Logic Type

Pin 1 Connection

CMOS

TTL

Power Down (Disable Output: Logic Low)

Tri-State (Disabled Output: High Impedance

Tri-State Input Voltage (Vih and Vil)

Standby Current

+2.0V

Minimum to enable output, +0.8V Maximum to disable

output, No Connect to enable output.

50µA Maximum (Pin 1 = Ground)

1 of 9

28-Jan-2016 2:01 PM

Ecliptek | EP14 Series Oscillator

http://www.ecliptek.com/oscillators/EP14/

Disable Current

30mA Maximum (Pin 1 = Ground)

Absolute Clock Jitter

±250pSec Maximum, ±100pSec Typical over Nominal Frequency of

1MHz to 33MHz

±100pSec Maximum, ±50pSec Typical over Nominal Frequency of

33.000001MHz to 125MHz

One Sigma Clock Period Jitter

±50pSec Maximum over Nominal Frequency of 1MHz to 33MHz

±30pSec Maximum over Nominal Frequency of 33.000001MHz to

125MHz

Aging (at 25°C)

±5ppm/year Maximum

-55°C to +125°C

Storage Temperature Range

Start Up Time

10mSec Maximum

2 of 9

28-Jan-2016 2:01 PM

Ecliptek | EP14 Series Oscillator

http://www.ecliptek.com/oscillators/EP14/

Mechanical Dimensions

All Dimensions in Millimeters

Pin 1: Power Down (Logic Low) or Tri-State (High Impedance)

Pin 2: Ground

Pin 3: Output

Pin 4: Supply Voltage

Marking Specifications

Line 1:

Line 2:

ECLIPTEK

XXXXXXM

XXXXXX = Nominal Frequency (5 Digits + Decimal)

M = Frequency unit of measure (MHz)

Line 3:

XXXXX

XXXXX = Ecliptek Manufacturing Identifier

3 of 9

28-Jan-2016 2:01 PM

Ecliptek | EP14 Series Oscillator

http://www.ecliptek.com/oscillators/EP14/

Environmental and Mechanical Specifications

Fine Leak Test

MIL-STD-883, Method 1014, Condition A

MIL-STD-883, Method 1014, Condition C

MIL-STD-202, Method 213, Condition C

MIL-STD-202, Method 210

Gross Leak Test

Mechanical Shock

Resistance to Soldering Heat

Resistance to Solvents

Solderability

MIL-STD-202, Method 215

MIL-STD-883, Method 2003

Temperature Cycling

Vibration

MIL-STD-883, Method 1010

MIL-STD-883, Method 2007, Condition A

81°C/W (degrees Celsius per Watt)

31°C/W (degrees Celsius per Watt)

Thermal Resistance (θ

)

4 of 9

28-Jan-2016 2:01 PM

Ecliptek | EP14 Series Oscillator

http://www.ecliptek.com/oscillators/EP14/

Tape & Reel Dimensions

1000 pieces per reel

Compliant to EIA-481

All Dimensions in Millimeters

5 of 9

28-Jan-2016 2:01 PM

Ecliptek | EP14 Series Oscillator

http://www.ecliptek.com/oscillators/EP14/

TTL Test Circuit

Note 1: An external 0.1µF low frequency tantalum bypass capacitor in parallel with a 0.01µF high frequency ceramic bypass

capacitor close to the package ground and V pin is required.

Note 2: A low input capacitance (<12pF), 10X Attentuation Factor, High Impedance (>10Mohms), and High bandwidth

(>300MHz) passive probe is recommended.

Note 3: Capacitance value C includes sum of all probe and fixture capacitance.

Note 4: Resistance value R is shown in Table I. See applicable specification sheet for â€˜Load Drive Capabilityâ€™.

Note 5: All diodes are MMBD7000, MMBD914, or equivalent.

CMOS Test Circuit

Note 1: An external 0.1µF low frequency tantalum bypass capacitor in parallel with a 0.01µF high frequency ceramic bypass

capacitor close to the package ground pin is required.

Note 2: A low input capacitance (<12pF), 10X Attentuation Factor, High Impedance (>10Mohms), and High bandwidth

(>300MHz) passive probe is recommended.

Note 3: Capacitance value includes sum of all probe and fixture capacitance. See applicable specification sheet for ‘Load

Drive Capability’.

6 of 9

28-Jan-2016 2:01 PM

Ecliptek | EP14 Series Oscillator

http://www.ecliptek.com/oscillators/EP14/

Recommended Solder Pad Dimensions

Tolerances = ±0.1

All Dimensions in Millimeters

7 of 9

28-Jan-2016 2:01 PM

Ecliptek | EP14 Series Oscillator

http://www.ecliptek.com/oscillators/EP14/

Solder Reflow Profile

Low Temperature Infrared/Convection

Note: Temperatures shown are applied to body of

device.

MAX to T (Ramp-up Rate)

5°C/second Maximum

Preheat

- Temperature Minimum (T MIN)

N/A

- Temperature Typical (T TYP)

150°C

- Temperature Maximum (T MAX)

N/A

- Time (t )

60 - 120 Seconds

5°C/second Maximum

Ramp-up Rate (T to T )

Time Maintained Above:

- Temperature (T )

150°C

- Time (t )

200 Seconds Maximum

Peak Temperature (T )

240°C Maximum

Target Peak Temperature (T Target)

240°C Maximum 2 Times / 230°C Maximum 1 Time

Time within 5°C of actual peak (t )

10 seconds Maximum 2 Times / 80 seconds Maximum 1 Time

Ramp-down Rate

5°C/second Maximum

Time 25°C to Peak Temperature (t)

Moisture Sensitivity Level

N/A

Level 1

High Temperature Manual Soldering

Note: Temperatures listed are applied to body of device.

260°C Maximum for 5 seconds Maximum, 2 times Maximum.

Low Temperature Manual Soldering

Note: Temperatures listed are applied to body of device.

185°C Maximum for 10 seconds Maximum, 2 times Maximum.

8 of 9

28-Jan-2016 2:01 PM

Ecliptek | EP14 Series Oscillator

http://www.ecliptek.com/oscillators/EP14/

1 - Build A Part Number

2 - Next Page

Select the parameters that meet your requirements and then click

Access these Part Number specific

resources and tools

Frequency in

Megahertz (1 to 125):

Some frequencies within this

range may not be available

Frequency

Tolerance/Stability:

Operating

Temperature Range:

Duty Cycle:

Pin 1 Connection:

Output Logic Type:

Packaging Options:

Part Numbering Guide

TOOLS

PRODUCT

ECLIPTEK

TERMS

Quick Quote

Crystals

Authorized Distributors

Contact

Terms of Sale

Legal

SmartSearch

Oscillators

Compliance Documents

Chipset Cross Reference

Competitor Cross Reference

Part Search

REACH Resources

RoHS Resources

End of Life

About

News

Our Quality

ISO9001

Feedback

9 of 9

28-Jan-2016 2:01 PM

相关型号：