EBE52UD6AJUA-8G-E [ELPIDA]
512MB DDR2 SDRAM SO-DIMM; 512MB DDR2 SDRAM SO- DIMM型号: | EBE52UD6AJUA-8G-E |
厂家: | ELPIDA MEMORY |
描述: | 512MB DDR2 SDRAM SO-DIMM |
文件: | 总28页 (文件大小:288K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DATA SHEET
512MB DDR2 SDRAM SO-DIMM
EBE52UD6AJUA (64M words × 64 bits, 2 Ranks)
Specifications
Features
• Density: 512MB
• Organization
• Double-data-rate architecture; two data transfers per
clock cycle
• The high-speed data transfer is realized by the 4 bits
64M words × 64 bits, 2 ranks
prefetch pipelined architecture
• Mounting 8 pieces of 512M bits DDR2 SDRAM
• Bi-directional differential data strobe (DQS and /DQS)
is transmitted/received with data for capturing data at
the receiver
sealed in FBGA
• Package: 200-pin socket type small outline dual in
line memory module (SO-DIMM)
• DQS is edge-aligned with data for READs; center-
PCB height: 30.0mm
Lead pitch: 0.6mm
Lead-free (RoHS compliant)
• Power supply: VDD = 1.8V ± 0.1V
• Data rate: 800Mbps/667Mbps (max.)
aligned with data for WRITEs
• Differential clock inputs (CK and /CK)
• DLL aligns DQ and DQS transitions with CK
transitions
• Commands entered on each positive CK edge; data
and data mask referenced to both edges of DQS
• Four internal banks for concurrent operation
(components)
• Data mask (DM) for write data
• Interface: SSTL_18
• Burst lengths (BL): 4, 8
• /CAS Latency (CL): 3, 4, 5, 6
• Posted CAS by programmable additive latency for
better command and data bus efficiency
• Off-Chip-Driver Impedance Adjustment and On-Die-
Termination for better signal quality
• Precharge: auto precharge option for each burst
• /DQS can be disabled for single-ended Data Strobe
access
operation
• Refresh: auto-refresh, self-refresh
• Refresh cycles: 8192 cycles/64ms
Average refresh period
7.8µs at 0°C ≤ TC ≤ +85°C
3.9µs at +85°C < TC ≤ +95°C
• Operating case temperature range
TC = 0°C to +95°C
Document No. E1084E30 (Ver. 3.0)
Date Published April 2008 (K) Japan
Printed in Japan
URL: http://www.elpida.com
Elpida Memory, Inc. 2007-2008
EBE52UD6AJUA
Ordering Information
Component
JEDEC speed bin
(CL-tRCD-tRP)
Data rate
Mbps (max.)
Contact
pad
Part number
Package
Mounted devices
EBE52UD6AJUA-8E-E
EBE52UD6AJUA-8G-E
DDR2-800 (5-5-5)
DDR2-800 (6-6-6)
EDE5116AJBG-8E-E
EDE5116AJBG-8E-E
800
200-pin SO-DIMM
(lead-free)
Gold
EDE5116AJBG-8E-E
EDE5116AJBG-6E-E
EBE52UD6AJUA-6E-E 667
DDR2-667 (5-5-5)
Pin Configurations
Front side
39 pin 41 pin
1 pin
2 pin
199 pin
42 pin
200 pin
40 pin
Back side
Front side
Back side
Pin No.
1
Pin name
VREF
VSS
Pin No.
51
53
55
57
59
61
63
65
67
69
71
73
75
77
79
81
83
85
87
89
91
93
95
97
99
Pin name
DQS2
VSS
DQ18
DQ19
VSS
DQ24
DQ25
VSS
DM3
NC
Pin No.
2
Pin name
VSS
Pin No.
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
82
84
86
88
90
92
94
96
98
100
Pin name
DM2
VSS
DQ22
DQ23
VSS
DQ28
DQ29
VSS
/DQS3
DQS3
VSS
DQ30
DQ31
VSS
CKE1
VDD
NC
3
4
DQ4
DQ5
VSS
5
DQ0
6
7
DQ1
8
9
VSS
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
DM0
VSS
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
/DQS0
DQS0
VSS
DQ6
DQ7
VSS
DQ2
DQ3
DQ12
DQ13
VSS
VSS
VSS
DQ26
DQ27
VSS
CKE0
VDD
NC
DQ8
DQ9
DM1
VSS
VSS
/DQS1
DQS1
VSS
CK0
/CK0
VSS
DQ10
DQ11
VSS
NC
DQ14
DQ15
VSS
NC
VDD
A12
VDD
A11
VSS
A9
VSS
A7
DQ16
DQ17
VSS
A8
DQ20
DQ21
VSS
A6
VDD
A5
VDD
A4
/DQS2
A3
NC
A2
Data Sheet E1084E30 (Ver. 3.0)
2
EBE52UD6AJUA
Front side
Pin No.
Back side
Pin No.
Pin name
A1
Pin No.
151
153
155
157
159
161
163
165
167
169
171
173
175
177
179
181
183
185
187
189
191
193
195
197
199
Pin name
DQ42
DQ43
VSS
Pin name
A0
Pin No.
Pin name
DQ46
DQ47
VSS
101
103
105
107
109
111
113
115
117
119
121
123
125
127
129
131
133
135
137
139
141
143
145
147
149
102
104
106
108
110
112
114
116
118
120
122
124
126
128
130
132
134
136
138
140
142
144
146
148
150
152
154
156
158
160
162
164
166
168
170
172
174
176
178
180
182
184
186
188
190
192
194
196
198
200
VDD
VDD
BA1
A10/AP
BA0
DQ48
DQ49
VSS
/RAS
/CS0
VDD
ODT0
NC
DQ52
DQ53
VSS
/WE
VDD
/CAS
/CS1
VDD
NC
CK1
VSS
/CK1
VSS
/DQS6
DQS6
VSS
VDD
NC
ODT1
VSS
DM6
VSS
VSS
DQ32
DQ33
VSS
DQ50
DQ51
VSS
DQ36
DQ37
VSS
DQ54
DQ55
VSS
/DQS4
DQS4
VSS
DQ56
DQ57
VSS
DM4
VSS
DQ60
DQ61
VSS
DQ38
DQ39
VSS
DQ34
DQ35
VSS
DM7
/DQS7
DQS7
VSS
VSS
DQ58
DQ59
VSS
DQ44
DQ45
VSS
DQ40
DQ41
VSS
DQ62
DQ63
VSS
SDA
/DQS5
DQS5
VSS
DM5
SCL
SA0
VSS
VDDSPD
SA1
Data Sheet E1084E30 (Ver. 3.0)
3
EBE52UD6AJUA
Pin Description
Pin name
Function
Address input
Row address
Column address
A0 to A12
A0 to A12
A0 to A9
A10 (AP)
Auto precharge
BA0, BA1
Bank select address
Data input/output
DQ0 to DQ63
/RAS
Row address strobe command
Column address strobe command
Write enable
/CAS
/WE
/CS0, /CS1
Chip select
CKE0, CKE1
Clock enable
CK0, CK1
Clock input
/CK0, /CK1
Differential clock input
Input and output data strobe
Input mask
DQS0 to DQS7, /DQS0 to /DQS7
DM0 to DM7
SCL
Clock input for serial PD
Data input/output for serial PD
Serial address input
Power for internal circuit
Power for serial EEPROM
Input reference voltage
Ground
SDA
SA0, SA1
VDD
VDDSPD
VREF
VSS
ODT0, ODT1
NC
ODT control
No connection
Data Sheet E1084E30 (Ver. 3.0)
4
EBE52UD6AJUA
Serial PD Matrix
Byte No. Function described
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Hex value Comments
Number of bytes utilized by module
0
1
1
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
80H
08H
128 bytes
256 bytes
manufacturer
Total number of bytes in serial PD
device
2
3
4
5
6
7
8
Memory type
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
1
0
0
0
0
1
0
0
1
0
0
0
0
0
1
0
1
0
0
1
08H
0DH
0AH
61H
40H
00H
05H
DDR2 SDRAM
Number of row address
Number of column address
Number of DIMM ranks
Module data width
13
10
2
64
Module data width continuation
Voltage interface level of this assembly
0
SSTL 1.8V
DDR SDRAM cycle time, CL = X
-8E (CL = 5)
-8G (CL = 6)
9
0
0
1
0
0
1
0
1
25H
2.5ns*1
0
0
0
0
1
1
0
1
0
0
1
0
0
0
1
0
25H
30H
2.5ns*1
3.0ns*1
-6E (CL = 5)
SDRAM access from clock (tAC)
-8E, -8G
-6E
10
0
1
0
0
0
0
0
0
40H
0.4ns*1
0
0
1
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
1
0
0
0
1
0
0
0
0
0
45H
00H
82H
10H
00H
00H
0.45ns*1
None.
7.8µs
× 16
11
12
13
14
15
DIMM configuration type
Refresh rate/type
Primary SDRAM width
Error checking SDRAM width
Reserved
None.
0
SDRAM device attributes:
16
17
0
0
0
0
0
0
0
0
1
0
1
1
0
0
0
0
0CH
04H
4,8
4
Burst length supported
SDRAM device attributes: Number of
banks on SDRAM device
SDRAM device attributes:
18
/CAS latency
0
0
1
1
1
0
0
0
38H
3, 4, 5
-8E, -6E
-8G
0
0
0
0
1
0
0
0
1
0
0
0
1
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
70H
01H
04H
00H
4, 5, 6
19
20
21
DIMM Mechanical Characteristics
DIMM type information
SDRAM module attributes
3.80mm max.
SO-DIMM
Normal
Weak Driver
22
23
SDRAM device attributes: General
0
0
0
0
0
0
1
1
03H
50Ω ODT Support
Minimum clock cycle time at CL = X − 1
-8E, -6E (CL = 4)
-8G (CL = 5)
0
0
0
0
1
1
1
1
1
0
1
0
0
0
1
0
3DH
30H
3.75ns*1
3.0ns*1
Maximum data access time (tAC) from
clock at CL = X − 1
24
25
0
1
0
1
0
0
0
0
50H
0.5ns*1
-8E, -6E (CL = 4)
-8G (CL = 5)
Minimum clock cycle time at CL = X − 2
-8E, -6E (CL = 3)
0
0
0
1
1
0
0
0
1
0
1
1
0
0
1
1
0
1
0
0
0
1
0
1
45H
50H
3DH
0.45ns*1
5.0ns*1
-8G (CL = 4)
3.75ns*1
Data Sheet E1084E30 (Ver. 3.0)
5
EBE52UD6AJUA
Byte No. Function described
Maximum data access time (tAC) from
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Hex value Comments
26
clock at CL = X − 2
0
1
1
0
0
0
0
0
60H
0.6ns*1
-8E, -6E (CL = 3)
-8G (CL = 4)
0
0
0
0
1
0
0
0
0
1
1
1
1
1
1
0
0
0
1
1
0
0
1
0
0
1
0
0
0
0
0
0
50H
32H
3CH
28H
0.5ns*1
12.5ns
15ns
Minimum row precharge time (tRP)
-8E
27
-8G, -6E
Minimum row active to row active delay
28
29
10ns
(tRRD)
Minimum /RAS to /CAS delay (tRCD)
-8E
0
0
0
0
0
0
0
1
1
1
1
0
1
1
0
0
0
1
1
0
0
1
1
0
1
0
0
0
0
0
1
0
32H
3CH
2DH
40H
12.5ns
15ns
-8G, -6E
Minimum active to precharge time
(tRAS)
Module rank density
30
31
45ns
256M bytes
Address and command setup time
before clock (tIS)
32
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
1
0
1
1
0
0
1
0
1
17H
20H
25H
0.17ns*1
0.20ns*1
0.25ns*1
-8E, -8G
-6E
Address and command hold time after
clock (tIH)
-8E, -8G
33
-6E
0
0
0
0
0
0
0
0
1
0
0
0
0
0
1
1
0
0
0
0
1
1
0
0
1
0
0
1
1
1
0
0
27H
05H
10H
12H
0.27ns*1
0.05ns*1
0.10ns*1
0.12ns*1
Data input setup time before clock (tDS)
-8E, -8G
-6E
Data input hold time after clock (tDH)
-8E, -8G
-6E
34
35
0
0
0
0
0
1
1
1
0
1
1
1
1
0
1
0
17H
3CH
0.17ns*1
15ns*1
36
37
Write recovery time (tWR)
Internal write to read command delay
(tWTR)
0
0
0
1
1
1
1
0
1EH
7.5ns*1
Internal read to precharge command
delay (tRTP)
Memory analysis probe characteristics
Extension of Byte 41 and 42
-8E
-8G, -6E
Active command period (tRC)
-8E
-8G, -6E
Auto refresh to active/
Auto refresh command cycle (tRFC)
38
39
40
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
1
0
1
1
1
0
0
0
0
1
0
1
0
1
1
0
0
1
1
1
1
0
0
0
1
1
1
0
0
1
1
1
0
0
0
0
1
0
0
1
0
1
1
0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
0
1
0
0
0
0
1EH
00H
30H
00H
39H
3CH
69H
80H
14H
18H
1EH
7.5ns*1
TBD
Undefined
57.5ns*1
60ns*1
41
42
43
44
105ns*1
8ns*1
SDRAM tCK cycle max. (tCK max.)
Dout to DQS skew
-8E, -8G
0.20ns*1
0.24ns*1
0.30ns*1
-6E
Data hold skew (tQHS)
-8E, -8G
-6E
45
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
22H
00H
00H
0.34ns*1
46
PLL relock time
Undefined
Undefined
47 to 61
Data Sheet E1084E30 (Ver. 3.0)
6
EBE52UD6AJUA
Byte No. Function described
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Hex value Comments
62
63
SPD Revision
Checksum for bytes 0 to 62
-8E
0
0
0
0
0
1
1
0
0
1
0
0
1
1
0
1
12H
2BH
Rev. 1.2
-8G
0
0
0
1
0
×
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
×
1
1
1
0
0
1
1
0
1
1
1
1
0
0
0
1
1
0
×
0
0
0
1
1
0
0
1
0
0
0
0
1
0
0
1
1
0
×
0
0
0
1
1
1
0
1
0
0
1
0
0
1
0
1
1
0
×
0
0
0
0
0
0
0
0
0
1
0
0
1
1
1
1
1
0
×
1
0
1
1
0
1
1
1
0
0
1
0
1
1
0
1
1
0
×
0
1
0
0
1
0
0
1
0
1
0
0
0
1
1
1
0
0
×
1
0
1
1
0
1
0
0
1
0
1
1
1
0FH
45H
7FH
FEH
00H
××
-6E
64 to 65 Manufacturer’s JEDEC ID code
66 Manufacturer’s JEDEC ID code
67 to 71 Manufacturer’s JEDEC ID code
Continuation code
Elpida Memory
72
73
74
75
76
77
78
79
80
81
82
83
84
85
Manufacturing location
Module part number
Module part number
Module part number
Module part number
Module part number
Module part number
Module part number
Module part number
Module part number
Module part number
Module part number
Module part number
Module part number
(ASCII-8bit code)
45H
42H
45H
35H
32H
55H
44H
36H
41H
4AH
55H
41H
2DH
E
B
E
5
2
U
D
6
A
J
U
A
—
Module part number
-8E, -8G
-6E
Module part number
-8E, -6E
86
0
0
0
0
0
1
1
1
0
1
1
0
1
0
0
0
1
1
0
1
0
0
0
1
38H
36H
45H
8
6
E
87
-8G
0
0
0
0
0
0
×
×
1
0
1
0
0
0
×
×
0
1
0
1
1
1
×
×
0
0
0
0
1
0
×
×
0
1
0
0
0
0
×
×
1
1
1
0
0
0
×
×
1
0
0
0
0
0
×
×
1
1
1
0
0
0
×
×
47H
2DH
45H
20H
30H
20H
××
G
88
89
90
91
92
93
94
Module part number
Module part number
Module part number
Revision code
—
E
(Space)
Initial
Revision code
(Space)
Manufacturing date
Manufacturing date
Year code (BCD)
Week code (BCD)
××
95 to 98 Module serial number
99 to 127 Manufacture specific data
Note: 1.These specifications are defined based on component specification, not module.
Data Sheet E1084E30 (Ver. 3.0)
7
EBE52UD6AJUA
Block Diagram
R
S2
S2
ODT1
ODT0
CKE1
R
R
S2
R
S2
R
S2
CKE0
/CS1
R
S2
/CS0
/CS CKE ODT
/LDQS
/CS CKE ODT
/LDQS
R
S1
R
S1
R
S1
/CS CKE ODT
/CS CKE ODT
/LDQS
R
S1
R
S1
R
S1
/DQS0
DQS0
DM0
/DQS4
DQS4
DM4
/LDQS
LDQS
LDM
LDQS
LDM
LDQS
LDM
LDQS
LDM
8
8
8
R
R
R
R
R
R
S1
S1
S1
S1
S1
I/O0 to I/O7
I/O0 to I/O7
/UDQS
DQ0 to DQ7
/DQS1
DQ32 to DQ39
/DQS5
I/O0 to I/O7
I/O0 to I/O7 D2
D6
S1
/UDQS
D0
D4
/UDQS
/UDQS
R
S1
R
S1
R
S1
UDQS
UDM
UDQS
UDM
DQS1
DQS5
UDQS
UDM
UDQS
UDM
DM1
DM5
8
R
S1
DQ8 to DQ15
I/O8 to I/O15
I/O8 to I/O15
DQ40 to DQ47
I/O8 to I/O15
I/O8 to I/O15
/CS CKE ODT
/LDQS
/CS CKE ODT
/LDQS
/CS CKE ODT
/LDQS
/CS CKE ODT
/LDQS
R
S1
R
S1
R
S1
R
S1
R
S1
R
S1
/DQS2
/DQS6
DQS2
DM2
DQS6
DM6
LDQS
LDM
LDQS
LDM
LDQS
LDM
LDQS
LDM
8
8
8
8
R
R
R
R
R
S1
S1
S1
S1
S1
I/O0 to I/O7
I/O0 to I/O7
/UDQS
DQ16 to DQ23
DQ48 to DQ55
I/O0 to I/O7 D3
D7
I/O0 to I/O7
R
S1
R
S1
R
S1
/UDQS
D1
D5
/DQS3
DQS3
DM3
/DQS7
DQS7
DM7
/UDQS
/UDQS
UDQS
UDM
UDQS
UDM
UDQS
UDM
UDQS
UDM
R
S1
R
S1
DQ24 to DQ31
I/O8 to I/O15
I/O8 to I/O15
DQ56 to DQ63
I/O8 to I/O15
I/O8 to I/O15
R
R
S2
BA0 to BA1
A0 to A12
BA0 to BA1: SDRAMs (D0 to D7)
A0 to A12: SDRAMs (D0 to D7)
Serial PD
SDA
S2
R
S2
R
S2
R
S2
SCL
SCL
A0
SDA
/RAS
/CAS
/WE
/RAS: SDRAMs (D0 to D7)
/CAS: SDRAMs (D0 to D7)
/WE: SDRAMs (D0 to D7)
SA0
SA1
U0
A1
A2
WP
CK0
4 loads
4 loads
/CK0
CK1
/CK1
Notes :
1. DQ wiring may be changed within a byte.
VDDSPD
SPD
SDRAMs (D0 to D7)
2. DQ, DQS, /DQS, ODT, DM, CKE, /CS relationships
must be meintained as shown.
VREF
VDD
SDRAMs (D0 to D7) VDD and VDDQ
SDRAMs (D0 to D7) SPD
VSS
* D0 to D7 : 512M bits DDR2 SDRAM
U0 : 2k bits EEPROM
Rs1 : 22
Ω
Rs2 : 3.0
Ω
Data Sheet E1084E30 (Ver. 3.0)
8
EBE52UD6AJUA
Electrical Specifications
• All voltages are referenced to VSS (GND).
Absolute Maximum Ratings
Parameter
Symbol
VT
Value
Unit
Notes
1
Voltage on any pin relative to VSS
Supply voltage relative to VSS
Short circuit output current
Power dissipation
–0.5 to +2.3
–0.5 to +2.3
50
V
VDD
IOS
PD
V
mA
W
°C
°C
1
4
Operating case temperature
Storage temperature
TC
0 to +95
–55 to +100
1, 2
1
Tstg
Notes: 1. DDR2 SDRAM component specification.
2. Supporting 0 to +85°C and being able to extend to +95°C with doubling auto-refresh commands in
frequency to a 32ms period (tREFI = 3.9µs) and higher temperature self-refresh entry via the control of
EMRS (2) bit A7 is required.
Caution Exposing the device to stress above those listed in Absolute Maximum Ratings could cause
permanent damage. The device is not meant to be operated under conditions outside the limits
described in the operational section of this specification Exposure to Absolute Maximum Rating
conditions for extended periods may affect device reliability.
DC Operating Conditions (TC = 0°C to +85°C) (DDR2 SDRAM Component Specification)
Parameter
Symbol
VDD, VDDQ
VSS
min.
typ.
1.8
0
max.
1.9
0
Unit
V
Notes
4
Supply voltage
1.7
0
V
VDDSPD
VREF
1.7
—
3.6
V
Input reference voltage
Termination voltage
DC input logic high
DC input low
0.49 × VDDQ
VREF − 0.04
VREF + 0.125
−0.3
0.50 × VDDQ 0.51 × VDDQ
V
1, 2
3
VTT
VREF
VREF + 0.04
VDDQ + 0.3
VREF – 0.125
V
VIH (DC)
VIL (DC)
VIH (AC)
VIL (AC)
V
V
AC input logic high
AC input low
VREF + 0.200
V
VREF – 0.200
V
Notes: 1. The value of VREF may be selected by the user to provide optimum noise margin in the system. Typically
the value of VREF is expected to be about 0.5 × VDDQ of the transmitting device and VREF are expected
to track variations in VDDQ.
2. Peak to peak AC noise on VREF may not exceed ±2% VREF (DC).
3. VTT of transmitting device must track VREF of receiving device.
4. VDDQ must be equal to VDD.
Data Sheet E1084E30 (Ver. 3.0)
9
EBE52UD6AJUA
AC Overshoot/Undershoot Specification (DDR2 SDRAM Component Specification)
Parameter
Pins
Specification
Unit
V
Command, Address,
CKE, ODT
Maximum peak amplitude allowed for overshoot
Maximum peak amplitude allowed for undershoot
0.5
0.5
V
Maximum overshoot area above VDD
DDR2-800
DDR2-667
Maximum undershoot area below VSS
DDR2-800
0.66
0.8
V-ns
V-ns
V-ns
0.66
DDR2-667
0.8
0.5
0.5
V-ns
V
Maximum peak amplitude allowed for overshoot
Maximum peak amplitude allowed for undershoot
CK, /CK
V
Maximum overshoot area above VDD
DDR2-800, 667
0.23
V-ns
Maximum undershoot area below VSS
DDR2-800, 667
Maximum peak amplitude allowed for overshoot
0.23
0.5
V-ns
V
DQ, DQS, /DQS,
UDQS, /UDQS,
LDQS, /LDQS,
Maximum peak amplitude allowed for undershoot
0.5
V
Maximum overshoot area above VDDQ
DDR2-800, 667
Maximum undershoot area below VSSQ
DDR2-800, 667
RDQS, /RDQS,
DM, UDM, LDM
0.23
0.23
V-ns
V-ns
Maximum amplitude
Overshoot area
VDD, VDDQ
Volts (V)
VSS, VSSQ
Undershoot area
Time (ns)
Overshoot/Undershoot Definition
Data Sheet E1084E30 (Ver. 3.0)
10
EBE52UD6AJUA
DC Characteristics 1 (TC = 0°C to +85°C, VDD = 1.8V ± 0.1V)
Parameter
Symbol
IDD0
Grade
max.
Unit
mA
Test condition
Operating current
(ACT-PRE)
(Another rank is in IDD2P)
-8E, -8G 320
-6E 300
one bank; tCK = tCK (IDD), tRC = tRC (IDD),
tRAS = tRAS min.(IDD);
CKE is H, /CS is H between valid commands;
Address bus inputs are SWITCHING;
Data bus inputs are SWITCHING
Operating current
-8E, -8G 440
-6E 400
IDD0
IDD1
mA
mA
(ACT-PRE)
(Another rank is in IDD3N)
one bank; IOUT = 0mA;
BL = 4, CL = CL(IDD), AL = 0;
tCK = tCK (IDD), tRC = tRC (IDD),
tRAS = tRAS min.(IDD); tRCD = tRCD (IDD);
CKE is H, /CS is H between valid commands;
Address bus inputs are SWITCHING;
Data pattern is same as IDD4W
Operating current
(ACT-READ-PRE)
(Another rank is in IDD2P)
-8E, -8G 380
-6E 360
Operating current
-8E, -8G 500
-6E
IDD1
mA
mA
(ACT-READ-PRE)
460
(Another rank is in IDD3N)
all banks idle;
tCK = tCK (IDD);
Precharge power-down
standby current
IDD2P
80
CKE is L;
Other control and address bus inputs are STABLE;
Data bus inputs are FLOATING
all banks idle;
tCK = tCK (IDD);
Precharge quiet standby
current
IDD2Q
IDD2N
120
160
mA
mA
CKE is H, /CS is H;
Other control and address bus inputs are STABLE;
Data bus inputs are FLOATING
all banks idle;
tCK = tCK (IDD);
Idle standby current
CKE is H, /CS is H;
Other control and address bus inputs are SWITCHING;
Data bus inputs are SWITCHING
all banks open;
Fast PDN Exit
tCK = tCK (IDD);
IDD3P-F
IDD3P-S
120
96
mA
mA
MRS(12) = 0
CKE is L;
Active power-down
standby current
Other control and address
bus inputs are STABLE;
Slow PDN Exit
Data bus inputs are
MRS(12) = 1
FLOATING
all banks open;
tCK = tCK (IDD), tRAS = tRAS max.(IDD), tRP = tRP (IDD);
CKE is H, /CS is H between valid commands;
Other control and address bus inputs are SWITCHING;
Data bus inputs are SWITCHING
-8E, -8G 320
-6E 280
Active standby current
IDD3N
mA
Operating current
all banks open, continuous burst reads, IOUT = 0mA;
BL = 4, CL = CL(IDD), AL = 0;
-8E, -8G 720
-6E 620
IDD4R
IDD4R
mA
mA
(Burst read operating)
(Another rank is in IDD2P)
tCK = tCK (IDD), tRAS = tRAS max.(IDD), tRP = tRP (IDD);
CKE is H, /CS is H between valid commands;
Address bus inputs are SWITCHING;
Operating current
(Burst read operating)
(Another rank is in IDD3N)
-8E, -8G 840
-6E 720
Data pattern is same as IDD4W
Operating current
(Burst write operating)
(Another rank is in IDD2P)
all banks open, continuous burst writes;
BL = 4, CL = CL(IDD), AL = 0;
tCK = tCK (IDD), tRAS = tRAS max.(IDD), tRP = tRP (IDD);
CKE is H, /CS is H between valid commands;
Address bus inputs are SWITCHING;
Data bus inputs are SWITCHING
-8E, -8G 680
-6E 600
IDD4W
IDD4W
mA
mA
Operating current
(Burst write operating)
(Another rank is in IDD3N)
-8E, -8G 800
-6E 700
Data Sheet E1084E30 (Ver. 3.0)
11
EBE52UD6AJUA
Parameter
Symbol
IDD5
Grade
max.
Unit
mA
Test condition
Auto-refresh current
(Another rank is in IDD2P)
-8E, -8G 460
-6E 440
tCK = tCK (IDD);
Refresh command at every tRFC (IDD) interval;
CKE is H, /CS is H between valid commands;
Other control and address bus inputs are SWITCHING;
Data bus inputs are SWITCHING
Auto-refresh current
(Another rank is in IDD3N)
-8E, -8G 580
-6E
IDD5
IDD6
mA
mA
540
Self Refresh Mode;
CK and /CK at 0V;
Self-refresh current
48
CKE ≤ 0.2V;
Other control and address bus inputs are FLOATING;
Data bus inputs are FLOATING
all bank interleaving reads, IOUT = 0mA;
BL = 4, CL = CL(IDD), AL = tRCD (IDD) −1 × tCK (IDD);
tCK = tCK (IDD), tRC = tRC (IDD), tRRD = tRRD(IDD),
tRCD = 1 × tCK (IDD);
CKE is H, /CS is H between valid commands;
Address bus inputs are STABLE during DESELECTs;
Data pattern is same as IDD4W;
Operating current
-8E, -8G 1000
-6E 960
IDD7
IDD7
mA
mA
(Bank interleaving)
(Another rank is in IDD2P)
Operating current
-8E, -8G 1120
-6E 1060
(Bank interleaving)
(Another rank is in IDD3N)
Notes: 1. IDD specifications are tested after the device is properly initialized.
2. Input slew rate is specified by AC Input Test Condition.
3. IDD parameters are specified with ODT disabled.
4. Data bus consists of DQ, DM, DQS, /DQS, RDQS and /RDQS. IDD values must be met with all
combinations of EMRS bits 10 and 11.
5. Definitions for IDD
L is defined as VIN ≤VIL (AC) (max.)
H is defined as VIN ≥VIH (AC) (min.)
STABLE is defined as inputs stable at an H or L level
FLOATING is defined as inputs at VREF = VDDQ/2
SWITCHING is defined as:
inputs changing between H and L every other clock cycle (once per two clocks) for address and control
signals, and inputs changing between H and L every other data transfer (once per clock) for DQ signals
not including masks or strobes.
6. Refer to AC Timing for IDD Test Conditions.
AC Timing for IDD Test Conditions
For purposes of IDD testing, the following parameters are to be utilized.
DDR2-800
DDR2-800
DDR2-667
Parameter
5-5-5
5
6-6-6
6
5-5-5
5
Unit
tCK
ns
CL (IDD)
tRCD (IDD)
tRC (IDD)
12.5
57.5
10
15
15
60
60
ns
tRRD (IDD)
tCK (IDD)
10
10
ns
2.5
2.5
45
3
ns
tRAS (min.)(IDD)
tRAS (max.)(IDD)
tRP (IDD)
45
45
ns
70000
12.5
105
70000
15
70000
15
ns
ns
tRFC (IDD)
105
105
ns
Data Sheet E1084E30 (Ver. 3.0)
12
EBE52UD6AJUA
DC Characteristics 2 (TC = 0°C to +85°C, VDD, VDDQ = 1.8V ± 0.1V)
(DDR2 SDRAM Component Specification)
Parameter
Symbol
ILI
Value
Unit
µA
Notes
Input leakage current
Output leakage current
2
5
VDD ≥ VIN ≥ VSS
VDDQ ≥ VOUT ≥ VSS
ILO
µA
Minimum required output pull-up under AC
VOH
VOL
VTT + 0.603
V
V
5
5
test load
Maximum required output pull-down under
AC test load
VTT − 0.603
Output timing measurement reference level VOTR
0.5 × VDDQ
+13.4
V
1
Output minimum sink DC current
Output minimum source DC current
IOL
mA
mA
3, 4, 5
2, 4, 5
IOH
−13.4
Notes: 1. The VDDQ of the device under test is referenced.
2. VDDQ = 1.7V; VOUT = 1.42V.
3. VDDQ = 1.7V; VOUT = 0.28V.
4. The DC value of VREF applied to the receiving device is expected to be set to VTT.
5. After OCD calibration to 18Ω at TC = 25°C, VDD = VDDQ = 1.8V.
DC Characteristics 3 (TC = 0°C to +85°C, VDD, VDDQ = 1.8V ± 0.1V)
(DDR2 SDRAM Component Specification)
Parameter
Symbol
min.
max.
Unit
V
Notes
1, 2
2
AC differential input voltage
AC differential cross point voltage
AC differential cross point voltage
VID (AC)
VIX (AC)
VOX (AC)
0.5
VDDQ + 0.6
0.5 × VDDQ − 0.175
0.5 × VDDQ − 0.125
0.5 × VDDQ + 0.175
0.5 × VDDQ + 0.125
V
V
3
Notes: 1. VID (AC) specifies the input differential voltage |VTR -VCP| required for switching, where VTR is the true
input signal (such as CK, DQS, RDQS) and VCP is the complementary input signal (such as /CK, /DQS,
/RDQS). The minimum value is equal to VIH (AC) − VIL (AC).
2. The typical value of VIX(AC) is expected to be about 0.5 × VDDQ of the transmitting device and VIX(AC)
is expected to track variations in VDDQ . VIX(AC) indicates the voltage at which differential input signals
must cross.
3. The typical value of VOX(AC) is expected to be about 0.5 × VDDQ of the transmitting device and
VOX(AC) is expected to track variations in VDDQ . VOX(AC) indicates the voltage at which differential
output signals must cross.
VDDQ
VTR
Crossing point
VID
VIX or VOX
VCP
VSSQ
Differential Signal Levels*1, 2
Data Sheet E1084E30 (Ver. 3.0)
13
EBE52UD6AJUA
ODT DC Electrical Characteristics (TC = 0°C to +85°C, VDD, VDDQ = 1.8V ± 0.1V)
(DDR2 SDRAM Component Specification)
Parameter
Symbol
Rtt1(eff)
Rtt2(eff)
Rtt3(eff)
∆VM
min.
60
typ.
75
max.
90
Unit
Ω
Note
Rtt effective impedance value for EMRS (A6, A2) = 0, 1; 75 Ω
Rtt effective impedance value for EMRS (A6, A2) = 1, 0; 150 Ω
Rtt effective impedance value for EMRS (A6, A2) = 1, 1; 50 Ω
Deviation of VM with respect to VDDQ/2
1
1
1
1
120
40
150
50
180
60
Ω
Ω
−6
+6
%
Note: 1. Test condition for Rtt measurements.
Measurement Definition for Rtt (eff)
Apply VIH (AC) and VIL (AC) to test pin separately, then measure current I(VIH (AC)) and I(VIL (AC)) respectively.
VIH (AC), and VDDQ values defined in SSTL_18.
VIH(AC)−VIL(AC)
Rtt(eff ) =
I(VIH(AC))−I(VIL(AC))
Measurement Definition for ∆VM
Measure voltage (VM) at test pin (midpoint) with no load.
2×VM
VDDQ
∆VM =
−1 ×100
OCD Default Characteristics (TC = 0°C to +85°C, VDD, VDDQ = 1.8V ± 0.1V)
(DDR2 SDRAM Component Specification)
Parameter
min.
12.6
0
typ.
18
max.
23.4
4
Unit
Ω
Notes
1, 5
Output impedance
Pull-up and pull-down mismatch
Output slew rate
Ω
1, 2
1.5
5
V/ns
3, 4
Notes: 1. Impedance measurement condition for output source DC current: VDDQ = 1.7V; VOUT = 1420mV;
(VOUT−VDDQ)/IOH must be less than 23.4Ω for values of VOUT between VDDQ and VDDQ−280mV.
Impedance measurement condition for output sink DC current: VDDQ = 1.7V; VOUT = 280mV;
VOUT/IOL must be less than 23.4Ω for values of VOUT between 0V and 280mV.
2. Mismatch is absolute value between pull up and pull down, both are measured at same temperature and
voltage.
3. Slew rate measured from VIL(AC) to VIH(AC).
4. The absolute value of the slew rate as measured from DC to DC is equal to or greater than the slew rate
as measured from AC to AC. This is guaranteed by design and characterization.
5. DRAM I/O specifications for timing, voltage, and slew rate are no longer applicable if OCD is changed
from default settings.
Data Sheet E1084E30 (Ver. 3.0)
14
EBE52UD6AJUA
Pin Capacitance (TA = 25°C, VDD = 1.8V ± 0.1V)
(DDR2 SDRAM Component Specification)
Parameter
Symbol Pins
min.
1.0
max.
2.0
Unit
pF
Notes
1
CLK input pin capacitance
CCK
CK, /CK
Input pin capacitance
-8E, -8G
/RAS, /CAS,
/WE, /CS,
CKE, ODT,
Address
1.0
1.0
1.75
2.0
pF
pF
1
1
CIN
-6E
DQ, DQS, /DQS,
UDQS, /UDQS,
LDQS, /LDQS,
RDQS, /RDQS,
DM, UDM, LDM
Input/output pin capacitance
CI/O
2.5
3.5
pF
2
Notes: 1. Matching within 0.25pF.
2. Matching within 0.50pF.
Data Sheet E1084E30 (Ver. 3.0)
15
EBE52UD6AJUA
AC Characteristics (TC = 0°C to +85°C, VDD, VDDQ = 1.8V ± 0.1V, VSS, VSSQ = 0V)
(DDR2 SDRAM Component Specification)
• New units tCK(avg) and nCK, are introduced in DDR2-800 and DDR2-667
tCK(avg): actual tCK(avg) of the input clock under operation.
nCK: one clock cycle of the input clock, counting the actual clock edges.
-8E
-8G
-6E
DDR2-667 (5-5-5)
Speed bin
Parameter
DDR2-800 (5-5-5)
DDR2-800 (6-6-6)
Symbol min.
max.
min.
15
max.
min.
15
max.
Unit Notes
Active to read or write command
delay
Precharge command period
Active to active/auto-refresh
command time
tRCD
tRP
12.5
12.5
57.5
ns
ns
ns
15
15
tRC
60
60
DQ output access time from CK,
/CK
DQS output access time from
CK, /CK
tAC
−400
+400
+350
0.52
0.52
−400
−350
0.48
0.48
+400
+350
0.52
0.52
−450
−400
0.48
0.48
+450
+400
0.52
0.52
ps
ps
10
10
13
13
tDQSCK −350
tCK
(avg)
tCK
(avg)
CK high-level width
CK low-level width
tCH (avg) 0.48
tCL(avg) 0.48
Min.
tHP
Min.
(tCL(abs),
tCH(abs))
Min.
(tCL(abs),
tCH(abs))
CK half period
(tCL(abs),
tCH(abs))
ps
6, 13
13
Clock cycle time
(CL = 6)
tCK (avg) 2500
8000
2500
8000
3000
8000
ps
(CL = 5)
(CL = 4)
(CL = 3)
tCK (avg) 2500
tCK (avg) 3750
tCK (avg) 5000
8000
8000
8000
3000
3750
5000
8000
8000
8000
3000
3750
5000
8000
8000
8000
ps
ps
ps
13
13
13
tDH
DQ and DM input hold time
DQ and DM input setup time
125
125
50
175
100
0.6
ps
ps
5
4
(base)
tDS
(base)
50
Control and Address input pulse
width for each input
DQ and DM input pulse width for
each input
Data-out high-impedance time
from CK,/CK
tCK
(avg)
tCK
(avg)
tIPW
tDIPW
tHZ
0.6
0.6
0.35
0.35
0.35
tAC max.
tAC max.
tAC max. ps
tAC max. ps
tAC max. ps
10
10
10
DQS, /DQS low-impedance time tLZ
tAC min.
tAC max. tAC min.
tAC max. tAC min.
from CK,/CK
DQ low-impedance time from
CK,/CK
(DQS)
2 ×
tAC min.
2 ×
tAC max.
2 ×
tAC max.
tLZ (DQ)
tAC min.
tAC min.
DQS-DQ skew for DQS and
associated DQ signals
DQ hold skew factor
DQ/DQS output hold time from
DQS
tDQSQ
tQHS
tQH
200
300
200
300
240
340
ps
ps
ps
7
8
tHP –
tQHS
tHP –
tQHS
tHP –
tQHS
DQS latching rising transitions to
associated clock edges
tCK
tDQSS
tDQSH
tDQSL
tDSS
−0.25
0.35
0.35
0.2
+0.25
−0.25
0.35
0.35
0.2
+0.25
−0.25
0.35
0.35
0.2
+0.25
(avg)
tCK
(avg)
tCK
(avg)
tCK
(avg)
DQS input high pulse width
DQS input low pulse width
DQS falling edge to CK setup
time
Data Sheet E1084E30 (Ver. 3.0)
16
EBE52UD6AJUA
-8E
-8G
-6E
DDR2-667 (5-5-5)
Speed bin
Parameter
DDR2-800 (5-5-5)
DDR2-800 (6-6-6)
Symbol min.
max.
min.
0.2
max.
min.
0.2
max.
Unit Notes
DQS falling edge hold time from
CK
Mode register set command
cycle time
tCK
(avg)
tDSH
0.2
2
tMRD
tWPST
2
2
nCK
tCK
(avg)
tCK
(avg)
Write postamble
Write preamble
0.4
0.6
0.4
0.35
250
175
0.9
0.4
0.6
0.4
0.35
275
200
0.9
0.4
0.6
tWPRE 0.35
Address and control input hold
time
Address and control input setup tIS
time
tIH
(base)
250
ps
5
175
0.9
0.4
ps
4
(base)
tCK
Read preamble
tRPRE
1.1
1.1
1.1
11
12
(avg)
tCK
(avg)
Read postamble
tRPST
0.6
0.6
0.6
Active to precharge command
Active to auto-precharge delay
tRAS
tRAP
45
70000
45
70000
45
70000
ns
tRCD min.
tRCD min.
tRCD min.
ns
Active bank A to active bank B
command period
tRRD
10
10
10
ns
/CAS to /CAS command delay
tCCD
tWR
2
2
2
nCK
ns
Write recovery time
15
15
15
WR +
RU (tRP/
tCK (avg))
WR +
RU (tRP/
tCK (avg))
WR +
RU (tRP/
tCK (avg))
Auto precharge write recovery +
precharge time
tDAL
nCK 1, 9
Internal write to read command
delay
Internal read to precharge
command delay
tWTR
tRTP
7.5
7.5
7.5
ns
14
7.5
7.5
7.5
ns
Exit self-refresh to a non-read
command
Exit self-refresh to a read
command
Exit precharge power down to
any non-read command
Exit active power down to read
command
tXSNR
tXSRD
tXP
tRFC + 10
tRFC + 10
tRFC + 10
ns
200
2
200
2
200
2
nCK
nCK
nCK
tXARD
2
2
2
3
Exit active power down to read
command
(slow exit/low power mode)
tXARDS 8 − AL
8 − AL
7 − AL
nCK 2, 3
CKE minimum pulse width
tCKE
tOIT
3
3
3
nCK
ns
(high and low pulse width)
Output impedance test driver
delay
MRS command to ODT update
delay
Auto-refresh to active/auto-
refresh command time
0
12
12
0
12
12
0
12
12
tMOD
tRFC
0
0
0
ns
105
105
105
ns
Average periodic refresh interval
tREFI
tREFI
7.8
3.9
7.8
3.9
7.8
3.9
µs
µs
(0°C ≤ TC ≤ +85°C)
(+85°C < TC ≤ +95°C)
Minimum time clocks remains
ON after CKE asynchronously
drops low
tIS +
tIS +
tCK(avg) +
tIH
tIS +
tCK(avg) +
tIH
tDELAY tCK(avg) +
ns
tIH
Data Sheet E1084E30 (Ver. 3.0)
17
EBE52UD6AJUA
Notes: 1. For each of the terms above, if not already an integer, round to the next higher integer.
2. AL: Additive Latency.
3. MRS A12 bit defines which active power down exit timing to be applied.
4. The figures of Input Waveform Timing 1 and 2 are referenced from the input signal crossing at the
VIH(AC) level for a rising signal and VIL(AC) for a falling signal applied to the device under test.
5. The figures of Input Waveform Timing 1 and 2 are referenced from the input signal crossing at the
VIL(DC) level for a rising signal and VIH(DC) for a falling signal applied to the device under test.
CK
DQS
/CK
/DQS
tIS
tIH
tIS
tIH
tDS tDH
tDS tDH
VDDQ
VDDQ
VIH (AC)(min.)
VIH (DC)(min.)
VREF
VIH (AC)(min.)
VIH (DC)(min.)
VREF
VIL (DC)(max.)
VIL (AC)(max.)
VSS
VIL (DC)(max.)
VIL (AC)(max.)
VSS
Input Waveform Timing 1 (tDS, tDH)
Input Waveform Timing 2 (tIS, tIH)
6.tHP is the minimum of the absolute half period of the actual input clock. tHP is an input parameter but not
an input specification parameter. It is used in conjunction with tQHS to derive the DRAM output timing
tQH.
The value to be used for tQH calculation is determined by the following equation;
tHP = min ( tCH(abs), tCL(abs) ),
where,
tCH(abs) is the minimum of the actual instantaneous clock high time;
tCL(abs) is the minimum of the actual instantaneous clock low time;
7. tQHS accounts for:
a. The pulse duration distortion of on-chip clock circuits, which represents how well the actual tHP at the
input is transferred to the output; and
b. The worst case push-out of DQS on one transition followed by the worst case pull-in of DQ on the
next transition, both of which are independent of each other, due to data pin skew, output pattern effects,
and p-channel to n-channel variation of the output drivers.
8. tQH = tHP – tQHS, where:
tHP is the minimum of the absolute half period of the actual input clock; and tQHS is the specification
value under the max column.
{The less half-pulse width distortion present, the larger the tQH value is; and the larger the valid data eye
will be.}
Examples:
a. If the system provides tHP of 1315ps into a DDR2-667 SDRAM, the DRAM provides tQH of 975ps
(min.)
b. If the system provides tHP of 1420ps into a DDR2-667 SDRAM, the DRAM provides tQH of 1080ps
(min.)
9. RU stands for round up. WR refers to the tWR parameter stored in the MRS.
10. When the device is operated with input clock jitter, this parameter needs to be derated by the actual
tERR(6-10per) of the input clock. (output deratings are relative to the SDRAM input clock.)
For example, if the measured jitter into a DDR2-667 SDRAM has tERR(6-10per) min. = −272ps and
tERR(6-10per) max. = +293ps, then tDQSCK min.(derated) = tDQSCK min. − tERR(6-10per) max. =
−400ps − 293ps = −693ps and tDQSCK max.(derated) = tDQSCK max. − tERR(6-10per) min. = 400ps +
272ps = +672ps. Similarly, tLZ(DQ) for DDR2-667 derates to tLZ(DQ) min.(derated) = −900ps − 293ps =
−1193ps and tLZ(DQ) max.(derated)= 450ps + 272ps = +722ps.
Data Sheet E1084E30 (Ver. 3.0)
18
EBE52UD6AJUA
11. When the device is operated with input clock jitter, this parameter needs to be derated by the actual
tJIT(per) of the input clock. (output deratings are relative to the SDRAM input clock.)
For example, if the measured jitter into a DDR2-667 SDRAM has tJIT(per) min. = −72ps and
tJIT(per) max. = +93ps, then tRPRE min.(derated) = tRPRE min. + tJIT(per) min. = 0.9 × tCK(avg) − 72ps
= +2178ps and tRPRE max.(derated) = tRPRE max. + tJIT(per) max. = 1.1 × tCK(avg) + 93ps = +2843ps.
12. When the device is operated with input clock jitter, this parameter needs to be derated by the actual
tJIT(duty) of the input clock. (output deratings are relative to the SDRAM input clock.)
For example, if the measured jitter into a DDR2-667 SDRAM has tJIT(duty) min. = −72ps and
tJIT(duty) max. = +93ps, then tRPST min.(derated) = tRPST min. + tJIT(duty) min. = 0.4 × tCK(avg) −
72ps = +928ps and tRPST max.(derated) = tRPST max. + tJIT(duty) max. = 0.6 × tCK(avg) + 93ps =
+1592ps.
13. Refer to the Clock Jitter table.
14. tWTR is at least two clocks (2 × tCK or 2 × nCK) independent of operation frequency.
Data Sheet E1084E30 (Ver. 3.0)
19
EBE52UD6AJUA
ODT AC Electrical Characteristics (DDR2 SDRAM Component Specification)
Parameter
Symbol
tAOND
tAON
min.
max.
Unit
tCK
ps
Notes
1, 3
ODT turn-on delay
2
2
ODT turn-on
tAC(min)
tAC(max) + 700
ODT turn-on (power down mode)
ODT turn-off delay
tAONPD
tAOFD
tAOF
tAC(min) + 2000
2tCK + tAC(max) + 1000
ps
2.5
2.5
tCK
ps
5
ODT turn-off
tAC(min)
tAC(max) + 600
2, 4, 5
ODT turn-off (power down mode)
ODT to power down entry latency
ODT power down exit latency
tAOFPD
tANPD
tAXPD
tAC(min) + 2000
2.5tCK + tAC(max) + 1000
ps
3
8
3
8
tCK
tCK
Notes: 1. ODT turn on time min is when the device leaves high impedance and ODT resistance begins to turn on.
ODT turn on time max is when the ODT resistance is fully on. Both are measured from tAOND.
2. ODT turn off time min is when the device starts to turn off ODT resistance.
ODT turn off time max is when the bus is in high impedance. Both are measured from tAOFD.
3. When the device is operated with input clock jitter, this parameter needs to be derated by the actual
tERR(6-10per) of the input clock. (output deratings are relative to the SDRAM input clock.)
4. When the device is operated with input clock jitter, this parameter needs to be derated by
{−tJIT(duty) max. − tERR(6-10per) max. } and { −tJIT(duty) min. − tERR(6-10per) min. } of the actual input
clock.(output deratings are relative to the SDRAM input clock.)
For example, if the measured jitter into a DDR2-667 SDRAM has tERR(6-10per) min. = −272ps,
tERR(6-10per) max. = +293ps, tJIT(duty) min. = −106ps and tJIT(duty) max. = +94ps, then
tAOF min.(derated) = tAOF min. + { −tJIT(duty) max. − tERR(6-10per) max. } = −450ps + { −94ps − 293ps}
= −837ps and tAOF max.(derated) = tAOF max. + { −tJIT(duty) min. − tERR(6-10per) min. } = 1050ps +
{ 106ps + 272ps} = +1428ps.
5. For tAOFD of DDR2-667/800, the 1/2 clock of nCK in the 2.5 × nCK assumes a tCH(avg), average input
clock high pulse width of 0.5 relative to tCK(avg). tAOF min. and tAOF max. should each be derated by
the same amount as the actual amount of tCH(avg) offset present at the DRAM input with respect to 0.5.
For example, if an input clock has a worst case tCH(avg) of 0.48, the tAOF min. should be derated by
subtracting 0.02 × tCK(avg) from it, whereas if an input clock has a worst case tCH(avg) of 0.52,
the tAOF max. should be derated by adding 0.02 × tCK(avg) to it. Therefore, we have;
tAOF min.(derated) = tAC min. − [0.5 − Min.(0.5, tCH(avg) min.)] × tCK(avg)
tAOF max.(derated) = tAC max. + 0.6 + [Max.(0.5, tCH(avg) max.) − 0.5] × tCK(avg)
or
tAOF min.(derated) = Min.(tAC min., tAC min. − [0.5 − tCH(avg) min.] × tCK(avg))
tAOF max.(derated) = 0.6 + Max.(tAC max., tAC max. + [tCH(avg) max. − 0.5] × tCK(avg))
where tCH(avg) min. and tCH(avg) max. are the minimum and maximum of tCH(avg) actually measured
at the DRAM input balls.
Data Sheet E1084E30 (Ver. 3.0)
20
EBE52UD6AJUA
AC Input Test Conditions (DDR2 SDRAM Component Specification)
Parameter
Symbol
Value
0.5 × VDDQ
1.0
Unit
V
Notes
1
Input reference voltage
VREF
Input signal maximum peak to peak swing
Input signal minimum slew rate
VSWING(max.)
SLEW
V
1
1.0
V/ns
2, 3
Notes: 1. Input waveform timing is referenced to the input signal crossing through the VIH/IL (AC) level applied to
the device under test.
2. The input signal minimum slew rate is to be maintained over the range from VREF to VIH(AC) (min.) for
rising edges and the range from VREF to VIL(AC) (max.) for falling edges as shown in the below figure.
3. AC timings are referenced with input waveforms switching from VIL(AC) to VIH(AC) on the positive
transitions and VIH(AC) to VIL(AC) on the negative transitions.
VDDQ
VIH (AC)(min.)
VIH (DC)(min.)
VSWING(max.)
VREF
VIL (DC)(max.)
VIL (AC)(max.)
VSS
∆TF
VREF
∆TR
−
VIL (AC)(max.)
VIH (AC) min.
−
VREF
Falling slew =
Rising slew =
∆TF
∆TR
AC Input Test Signal Wave forms
Measurement point
DQ
VTT
RT =25 Ω
Output Load
Data Sheet E1084E30 (Ver. 3.0)
21
EBE52UD6AJUA
Clock Jitter [DDR2-800, 667]
-8E, -8G
800
-6E
Frequency (Mbps)
Parameter
667
Symbol
min.
max.
8000
100
min.
3000
−125
max.
8000
125
Unit
ps
Notes
Average clock period
Clock period jitter
tCK (avg)
tJIT (per)
2500
−100
1
5
ps
Clock period jitter during
DLL locking period
Cycle to cycle period jitter
Cycle to cycle clock period jitter
during DLL locking period
tJIT
−80
80
−100
100
250
200
ps
ps
ps
5
6
6
(per, lck)
tJIT (cc)
200
160
tJIT (cc, lck)
Cumulative error across 2 cycles
Cumulative error across 3 cycles
Cumulative error across 4 cycles
Cumulative error across 5 cycles
tERR (2per) −150
tERR (3per) −175
tERR (4per) −200
tERR (5per) −200
150
175
200
200
−175
−225
−250
−250
175
225
250
250
ps
ps
ps
ps
7
7
7
7
Cumulative error across
tERR
−300
300
450
−350
−450
350
450
ps
ps
7
7
n=6,7,8,9,10 cycles
(6-10per)
Cumulative error across
n=11, 12,…49,50 cycles
tERR
(11-50per)
−450
Average high pulse width
Average low pulse width
Duty cycle jitter
tCH (avg)
tCL (avg)
tJIT (duty)
0.48
0.48
−100
0.52
0.52
100
0.48
0.48
−125
0.52
0.52
125
tCK (avg)
tCK (avg)
ps
2
3
4
Notes: 1. tCK (avg) is calculated as the average clock period across any consecutive 200cycle window.
N
tCK(avg) =
tCKj
N
∑
j =1
N = 200
2. tCH (avg) is defined as the average high pulse width, as calculated across any consecutive 200 high
pulses.
N
tCH(avg) =
tCHj (N ×tCK(avg))
∑
j =1
N = 200
3. tCL (avg) is defined as the average low pulse width, as calculated across any consecutive 200 low pulses.
N
tCL(avg) =
tCLj (N × tCK(avg))
∑
j =1
N = 200
4. tJIT (duty) is defined as the cumulative set of tCH jitter and tCL jitter. tCH jitter is the largest deviation of
any single tCH from tCH (avg). tCL jitter is the largest deviation of any single tCL from tCL (avg).
tJIT (duty) is not subject to production test.
tJIT (duty) = Min./Max. of {tJIT (CH), tJIT (CL)}, where:
tJIT (CH) = {tCHj- tCH (avg) where j = 1 to 200}
tJIT (CL) = {tCLj − tCL (avg) where j = 1 to 200}
5. tJIT (per) is defined as the largest deviation of any single tCK from tCK (avg).
tJIT (per) = Min./Max. of { tCKj − tCK (avg) where j = 1 to 200}
tJIT (per) defines the single period jitter when the DLL is already locked. tJIT (per, lck) uses the same
definition for single period jitter, during the DLL locking period only. tJIT (per) and tJIT (per, lck) are not
subject to production test.
Data Sheet E1084E30 (Ver. 3.0)
22
EBE52UD6AJUA
6. tJIT (cc) is defined as the absolute difference in clock period between two consecutive clock cycles:
tJIT (cc) = Max. of |tCKj+1 − tCKj|
tJIT (cc) is defines the cycle to cycle jitter when the DLL is already locked. tJIT (cc, lck) uses the same
definition for cycle to cycle jitter, during the DLL locking period only. tJIT (cc) and tJIT (cc, lck) are not
subject to production test.
7. tERR (nper) is defined as the cumulative error across multiple consecutive cycles from tCK (avg).
tERR (nper) is not subject to production test.
n
tERR(nper) =
tCKj − n×tCK(avg))
∑
j =1
2 ≤ n ≤ 50 for tERR (nper)
8. These parameters are specified per their average values, however it is understood that the following
relationship between the average timing and the absolute instantaneous timing hold at all times.
(minimum and maximum of spec values are to be used for calculations in the table below.)
Parameter
Symbol
min.
max.
Unit
Absolute clock period
tCK (abs) tCK (avg) min. + tJIT (per) min. tCK (avg) max. + tJIT (per) max. ps
Absolute clock high pulse
tCH (avg) min. × tCK (avg) min. + tCH (avg) max. × tCK (avg) max.
tCH (abs)
tCL (abs)
ps
ps
width
tJIT (duty) min.
+ tJIT (duty) max.
Absolute clock low pulse
width
tCL (avg) min. × tCK (avg) min. + tCL (avg) max. × tCK (avg) max.
tJIT (duty) min. + tJIT (duty) max.
Example: For DDR2-667, tCH(abs) min. = ( 0.48 × 3000 ps ) - 125ps = 1315ps
Data Sheet E1084E30 (Ver. 3.0)
23
EBE52UD6AJUA
Pin Functions
CK, /CK (input pin)
The CK and the /CK are the master clock inputs. All inputs except DMs, DQSs and DQs are referred to the cross
point of the CK rising edge and the VREF level. When a read operation, DQSs and DQs are referred to the cross
point of the CK and the /CK. When a write operation, DMs and DQs are referred to the cross point of the DQS and
the VREF level. DQSs for write operation are referred to the cross point of the CK and the /CK.
/CS (input pin)
When /CS is low, commands and data can be input. When /CS is high, all inputs are ignored. However, internal
operations (bank active, burst operations, etc.) are held.
/RAS, /CAS, and /WE (input pins)
These pins define operating commands (read, write, etc.) depending on the combinations of their voltage levels.
See "Command operation".
A0 to A12 (input pins)
Row address (AX0 to AX12) is determined by the A0 to the A12 level at the cross point of the CK rising edge and the
VREF level in a bank active command cycle. Column address (AY0 to AY9) is loaded via the A0 to the A9 at the
cross point of the CK rising edge and the VREF level in a read or a write command cycle. This column address
becomes the starting address of a burst operation.
A10 (AP) (input pin)
A10 defines the precharge mode when a precharge command, a read command or a write command is issued. If
A10 = high when a precharge command is issued, all banks are precharged. If A10 = low when a precharge
command is issued, only the bank that is selected by BA1, BA0 is precharged. If A10 = high when read or write
command, auto-precharge function is enabled. While A10 = low, auto-precharge function is disabled.
BA0 and BA1 (input pins)
BA0, BA1 are bank select signals (BA). The memory array is divided into bank 0, bank 1, bank 2 and bank 3. (See
Bank Select Signal Table)
[Bank Select Signal Table]
BA0
L
BA1
L
Bank 0
Bank 1
H
L
Bank 2
L
H
Bank 3
H
H
Remark: H: VIH. L: VIL.
CKE (input pin)
CKE controls power down and self-refresh. The power down and the self-refresh commands are entered when the
CKE is driven low and exited when it resumes to high.
The CKE level must be kept for 1 CK cycle at least, that is, if CKE changes at the cross point of the CK rising edge
and the VREF level with proper setup time tIS, at the next CK rising edge CKE level must be kept with proper hold
time tIH.
DQ (input and output pins)
Data are input to and output from these pins.
DQS and /DQS (input and output pin)
DQS and /DQS provide the read data strobes (as output) and the write data strobes (as input).
Data Sheet E1084E30 (Ver. 3.0)
24
EBE52UD6AJUA
DM (input pins)
DM is the reference signal of the data input mask function. DMs are sampled at the cross point of DQS and /DQS.
VDD (power supply pins)
1.8V is applied. (VDD is for the internal circuit.)
VDDSPD (power supply pin)
1.8V is applied (For serial EEPROM).
VSS (power supply pin)
Ground is connected.
Detailed Operation Part and Timing Waveforms
Refer to the EDE5108AJBG, EDE5116AJBG datasheet (E1044E).
Data Sheet E1084E30 (Ver. 3.0)
25
EBE52UD6AJUA
Physical Outline
Unit: mm
3.80 Max
Front side
2.00 Min
11.55
17.55
(DATUM -A-)
4x Full R
Component area
(Front)
A
B
D
11.40
2.15
47.40
2.45
2.15
1.00 ± 0.10
67.60
Back side
2.45
63.60
C
Component area
(Back)
(DATUM -A-)
Detail A
Detail B
FULL R
0.60
2.70
4.20
1.00 ± 0.10
0.45 ± 0.03
Detail C
Detail D
Contact pad
4.20
2.40
ECA-TS2-0209-01
Data Sheet E1084E30 (Ver. 3.0)
26
EBE52UD6AJUA
CAUTION FOR HANDLING MEMORY MODULES
When handling or inserting memory modules, be sure not to touch any components on the modules, such as
the memory ICs, chip capacitors and chip resistors. It is necessary to avoid undue mechanical stress on
these components to prevent damaging them.
In particular, do not push module cover or drop the modules in order to protect from mechanical defects,
which would be electrical defects.
When re-packing memory modules, be sure the modules are not touching each other.
Modules in contact with other modules may cause excessive mechanical stress, which may damage the
modules.
MDE0202
NOTES FOR CMOS DEVICES
PRECAUTION AGAINST ESD FOR MOS DEVICES
1
Exposing the MOS devices to a strong electric field can cause destruction of the gate
oxide and ultimately degrade the MOS devices operation. Steps must be taken to stop
generation of static electricity as much as possible, and quickly dissipate it, when once
it has occurred. Environmental control must be adequate. When it is dry, humidifier
should be used. It is recommended to avoid using insulators that easily build static
electricity. MOS devices must be stored and transported in an anti-static container,
static shielding bag or conductive material. All test and measurement tools including
work bench and floor should be grounded. The operator should be grounded using
wrist strap. MOS devices must not be touched with bare hands. Similar precautions
need to be taken for PW boards with semiconductor MOS devices on it.
2
HANDLING OF UNUSED INPUT PINS FOR CMOS DEVICES
No connection for CMOS devices input pins can be a cause of malfunction. If no
connection is provided to the input pins, it is possible that an internal input level may be
generated due to noise, etc., hence causing malfunction. CMOS devices behave
differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed
high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected
to VDD or GND with a resistor, if it is considered to have a possibility of being an output
pin. The unused pins must be handled in accordance with the related specifications.
3
STATUS BEFORE INITIALIZATION OF MOS DEVICES
Power-on does not necessarily define initial status of MOS devices. Production process
of MOS does not define the initial operation status of the device. Immediately after the
power source is turned ON, the MOS devices with reset function have not yet been
initialized. Hence, power-on does not guarantee output pin levels, I/O settings or
contents of registers. MOS devices are not initialized until the reset signal is received.
Reset operation must be executed immediately after power-on for MOS devices having
reset function.
CME0107
Data Sheet E1084E30 (Ver. 3.0)
27
EBE52UD6AJUA
The information in this document is subject to change without notice. Before using this document, confirm that this is the latest version.
No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of Elpida Memory, Inc.
Elpida Memory, Inc. does not assume any liability for infringement of any intellectual property rights
(including but not limited to patents, copyrights, and circuit layout licenses) of Elpida Memory, Inc. or
third parties by or arising from the use of the products or information listed in this document. No license,
express, implied or otherwise, is granted under any patents, copyrights or other intellectual property
rights of Elpida Memory, Inc. or others.
Descriptions of circuits, software and other related information in this document are provided for
illustrative purposes in semiconductor product operation and application examples. The incorporation of
these circuits, software and information in the design of the customer's equipment shall be done under
the full responsibility of the customer. Elpida Memory, Inc. assumes no responsibility for any losses
incurred by customers or third parties arising from the use of these circuits, software and information.
[Product applications]
Be aware that this product is for use in typical electronic equipment for general-purpose applications.
Elpida Memory, Inc. makes every attempt to ensure that its products are of high quality and reliability.
However, users are instructed to contact Elpida Memory's sales office before using the product in
aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment,
medical equipment for life support, or other such application in which especially high quality and
reliability is demanded or where its failure or malfunction may directly threaten human life or cause risk
of bodily injury.
[Product usage]
Design your application so that the product is used within the ranges and conditions guaranteed by
Elpida Memory, Inc., including the maximum ratings, operating supply voltage range, heat radiation
characteristics, installation conditions and other related characteristics. Elpida Memory, Inc. bears no
responsibility for failure or damage when the product is used beyond the guaranteed ranges and
conditions. Even within the guaranteed ranges and conditions, consider normally foreseeable failure
rates or failure modes in semiconductor devices and employ systemic measures such as fail-safes, so
that the equipment incorporating Elpida Memory, Inc. products does not cause bodily injury, fire or other
consequential damage due to the operation of the Elpida Memory, Inc. product.
[Usage environment]
Usage in environments with special characteristics as listed below was not considered in the design.
Accordingly, our company assumes no responsibility for loss of a customer or a third party when used in
environments with the special characteristics listed below.
Example:
1) Usage in liquids, including water, oils, chemicals and organic solvents.
2) Usage in exposure to direct sunlight or the outdoors, or in dusty places.
3) Usage involving exposure to significant amounts of corrosive gas, including sea air, CL2, H2S, NH3,
SO2, and NO .
x
4) Usage in environments with static electricity, or strong electromagnetic waves or radiation.
5) Usage in places where dew forms.
6) Usage in environments with mechanical vibration, impact, or stress.
7) Usage near heating elements, igniters, or flammable items.
If you export the products or technology described in this document that are controlled by the Foreign
Exchange and Foreign Trade Law of Japan, you must follow the necessary procedures in accordance
with the relevant laws and regulations of Japan. Also, if you export products/technology controlled by
U.S. export control regulations, or another country's export control laws or regulations, you must follow
the necessary procedures in accordance with such laws or regulations.
If these products/technology are sold, leased, or transferred to a third party, or a third party is granted
license to use these products, that third party must be made aware that they are responsible for
compliance with the relevant laws and regulations.
M01E0706
Data Sheet E1084E30 (Ver. 3.0)
28
相关型号:
©2020 ICPDF网 联系我们和版权申明