EDS1232AHTA-75TI-E [ELPIDA]
128M bits SDRAM WTR (Wide Temperature Range); 128M位的SDRAM WTR (宽温度范围)型号: | EDS1232AHTA-75TI-E |
厂家: | ELPIDA MEMORY |
描述: | 128M bits SDRAM WTR (Wide Temperature Range) |
文件: | 总50页 (文件大小:725K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DATA SHEET
128M bits SDRAM
WTR (Wide Temperature Range)
EDS1232AHTA-TI (4M words × 32 bits)
Specifications
Pin Configurations
• Density: 128M bits
/xxx indicates active low signal.
• Organization
86-pin Plastic TSOP(II)
1M words × 32 bits × 4 banks
• Package: 86-pin plastic TSOP (II)
Lead-free (RoHS compliant)
• Power supply: VDD, VDDQ = 3.3V ± 0.3V
• Clock frequency: 133MHz (max.)
• Four internal banks for concurrent operation
• Interface: LVTTL
• Burst lengths (BL): 1, 2, 4, 8, full page
• Burst type (BT):
Sequential (1, 2, 4, 8, full page)
Interleave (1, 2, 4, 8)
• /CAS Latency (CL): 2, 3
VDD
DQ0
V
SS
1
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
DQ15
VSSQ
DQ14
DQ13
VDDQ
DQ12
DQ11
VSSQ
DQ10
DQ9
VDDQ
DQ8
NC
2
VDDQ
DQ1
3
4
DQ2
5
VSSQ
DQ3
6
7
DQ4
8
VDDQ
DQ5
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
DQ6
VSSQ
DQ7
NC
VDD
VSS
DQM0
/WE
DQM1
NC
/CAS
/RAS
/CS
NC
CLK
CKE
A9
A11
BA0
A8
BA1
A7
• Precharge: auto precharge option for each burst
A10(AP)
A0
A6
access
A5
A1
A2
A4
• Refresh: auto-refresh, self-refresh
• Refresh cycles: 4096 cycles/64ms
Average refresh period: 15.6µs
• Operating ambient temperature range
TA = –40°C to +85°C
A3
DQM2
VDD
DQM3
VSS
NC
NC
DQ16
VSSQ
DQ17
DQ18
VDDQ
DQ19
DQ20
VSSQ
DQ21
DQ22
VDDQ
DQ23
VDD
DQ31
VDDQ
DQ30
DQ29
VSSQ
DQ28
DQ27
VDDQ
DQ26
DQ25
VSSQ
DQ24
VSS
Features
• ×32 organization
• Single pulsed /RAS
• Burst read/write operation and burst read/single write
(Top view)
operation capability
A0 to A11
BA0, BA1
DQ0 to DQ31
/CS
Address inputs
Bank select
Data input/output
Chip select
• Byte control by DQM
• Wide temperature range
TA = –40°C to +85°C
/RAS
/CAS
/WE
Row address strobe
Column address strobe
Write enable
DQM0 to DQM3
DQ mask enable
Clock enable
CKE
CLK
Clock input
VDD
VSS
Supply voltage
Ground
VDDQ
Supply voltage for DQ
Ground for DQ
No connection
VSSQ
NC
Document No. E1164E20 (Ver. 2.0)
This product became EOL in March, 2010.
Date Published March 2008 (K) Japan
Printed in Japan
URL: http://www.elpida.com
Elpida Memory, Inc. 2007-2008
EDS1232AHTA-TI
Ordering Information
Supply
voltage
Organization Internal
(words × bits) Banks
Clock frequency
MHz (max.)
Part number
/CAS latency
Package
133
100
3
2
EDS1232AHTA-75TI-E
3.3V
4M × 32
4
86-pin plastic TSOP (II)
Part Number
E D S 12 32 A H TA - 75 TI - E
Elpida Memory
Environment Code
E: Lead Free
Type
D: Monolithic Device
(RoHS compliant)
Product Family
S: SDRAM
Spec Detail
TI: WTR (−40°C to +85°C)
Density / Bank
12: 128M/4-bank
Speed
75: 133MHz/CL3
100MHz/CL2
Organization
32: x32
Power Supply, Interface
A: 3.3V, LVTTL
Package
TA: TSOP (II)
Die Rev.
Data Sheet E1164E20 (Ver. 2.0)
2
EDS1232AHTA-TI
CONTENTS
Specifications.................................................................................................................................................1
Features.........................................................................................................................................................1
Pin Configurations .........................................................................................................................................1
Ordering Information......................................................................................................................................2
Part Number ..................................................................................................................................................2
Electrical Specifications.................................................................................................................................4
Block Diagram .............................................................................................................................................10
Pin Function.................................................................................................................................................11
Command Operation ...................................................................................................................................13
Simplified State Diagram.............................................................................................................................21
Mode Register Configuration.......................................................................................................................22
Power-up sequence.....................................................................................................................................24
Operation of the SDRAM.............................................................................................................................25
Timing Waveforms.......................................................................................................................................41
Package Drawing ........................................................................................................................................47
Recommended Soldering Conditions..........................................................................................................48
Data Sheet E1164E20 (Ver. 2.0)
3
EDS1232AHTA-TI
Electrical Specifications
• All voltages are referenced to VSS (GND).
• After power up, execute power up sequence and initialization sequence before proper device operation is achieved
(refer to the Power up sequence).
Absolute Maximum Ratings
Parameter
Symbol
VT
Rating
Unit
V
Note
Voltage on any pin relative to VSS
Supply voltage relative to VSS
Short circuit output current
Power dissipation
–0.5 to VDD + 0.5 (≤ 4.6 (max.))
VDD
IOS
PD
–0.5 to +4.6
50
V
mA
W
1.0
Operating ambient temperature
Storage temperature
TA
–40 to +85
–55 to +125
°C
°C
Tstg
Caution
Exposing the device to stress above those listed in Absolute Maximum Ratings could cause
permanent damage. The device is not meant to be operated under conditions outside the limits
described in the operational section of this specification. Exposure to Absolute Maximum Rating
conditions for extended periods may affect device reliability.
Recommended DC Operating Conditions (TA = –40°C to +85°C)
Parameter
Symbol
VDD, VDDQ
VSS, VSSQ
VIH
min.
3.0
0
max.
Unit
V
Notes
Supply voltage
3.6
1
2
3
4
0
V
Input high voltage
Input low voltage
2.0
–0.3
VDD + 0.3
0.8
V
VIL
V
Notes: 1. The supply voltage with all VDDand VDDQ pins must be on the same level.
2. The supply voltage with all VSS and VSSQ pins must be on the same level.
3. VIH (max.) = VDD + 1.5V (pulse width ≤ 5ns).
4. VIL (min.) = VSS – 1.5V (pulse width ≤ 5ns).
Data Sheet E1164E20 (Ver. 2.0)
4
EDS1232AHTA-TI
DC Characteristics 1 (TA = –40°C to +85°C, VDD, VDDQ = 3.3V ± 0.3V, VSS, VSSQ = 0V)
Parameter
Symbol
IDD1
Grade
max.
90
Unit
mA
Test condition
Burst length = 1
tRC = tRC (min.)
Notes
1, 2, 3
Operating current
CKE = VIL,
Standby current in power down
IDD2P
3
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
6
tCK = tCK (min.)
Standby current in power down
(input signal stable)
IDD2PS
IDD2N
IDD2NS
IDD3P
2
CKE = VIL, tCK = ∞
7
CKE, /CS = VIH,
tCK = tCK (min.)
CKE = VIH, tCK = ∞,
/CS = VIH
CKE = VIL,
tCK = tCK (min.)
Standby current in non power down
20
8
4
Standby current in non power down
(input signal stable)
8
Active standby current in power down
4
1, 2, 6
2, 7
1, 2, 4
2, 8
1, 2, 5
3
Active standby current in power down
(input signal stable)
IDD3PS
3
CKE = VIL, tCK = ∞
CKE, /CS = VIH,
tCK = tCK (min.)
CKE = VIH, tCK = ∞,
/CS = VIH
tCK = tCK (min.),
BL = 4
Active standby current in non power down IDD3N
20
15
100
180
2
Active standby current in non power down
IDD3NS
(input signal stable)
Burst operating current
Refresh current
IDD4
IDD5
IDD6
tRC = tRC (min.)
VIH ≥ VDD – 0.2V
VIL ≤ 0.2V
Self refresh current
Notes: 1. IDD depends on output load condition when the device is selected. IDD (max.) is specified at the output
open condition.
2. One bank operation.
3. Input signals are changed once per one clock.
4. Input signals are changed once per two clocks.
5. Input signals are changed once per four clocks.
6. After power down mode, CLK operating current.
7. After power down mode, no CLK operating current.
8. Input signals are VIH or VIL fixed.
Data Sheet E1164E20 (Ver. 2.0)
5
EDS1232AHTA-TI
DC Characteristics 2 (TA = –40°C to +85°C, VDD, VDDQ = 3.3V ± 0.3V, VSS, VSSQ = 0V)
Parameter
Symbol
ILI
min.
–1
max.
1
Unit
µA
µA
V
Test condition
Notes
Input leakage current
Output leakage current
Output high voltage
Output low voltage
0 ≤ VIN ≤ VDD
ILO
–1.5
2.4
—
1.5
—
0 ≤ VOUT ≤ VDD, DQ = disable
IOH = –2 mA
VOH
VOL
0.4
V
IOL = 2 mA
Pin Capacitance (TA = 25°C, VDD, VDDQ = 3.3V ± 0.3V)
Parameter
Symbol
CI1
Pins
CLK
min.
2.5
typ.
max.
4.0
Unit
pF
Notes
Input capacitance
—
1, 2, 4
Address, CKE, /CS,
/RAS, /CAS, /WE,
DQM
CI2
2.5
—
4.0
pF
1, 2, 4
Data input/output
capacitance
CI/O
DQ
4.0
—
6.5
pF
1, 2, 3, 4
Notes: 1. Capacitance measured with Boonton Meter or effective capacitance measuring method.
2. Measurement condition: f = 1MHz, 1.4V bias, 200mV swing.
3. DQM = VIH to disable DOUT.
4. This parameter is sampled and not 100% tested.
Data Sheet E1164E20 (Ver. 2.0)
6
EDS1232AHTA-TI
AC Characteristics (TA = –40°C to +85°C, VDD, VDDQ = 3.3V ± 0.3V, VSS, VSSQ = 0V)
-75
Parameter
System clock cycle time
(CL = 2)
Symbol
tCK
min.
max.
—
Unit
ns
Notes
1
10
(CL = 3)
tCK
tCH
tCL
tAC
tOH
tLZ
7.5
2.5
2.5
—
—
ns
ns
ns
1
CLK high pulse width
—
1, 5
1, 5
1, 2, 5
1, 2, 5
1, 2, 3, 5
1, 4
1, 5
1, 5
1
CLK low pulse width
—
Access time from CLK
Data-out hold time
5.4
—
2
ns
ns
ns
ns
ns
ns
ns
CLK to Data-out low impedance
CLK to Data-out high impedance
Input setup time
0
—
tHZ
tSI
—
5.4
—
1.5
0.8
67.5
45
Input hold time
tHI
—
Ref/Active to Ref/Active command period
tRC
tRAS
—
Active to Precharge command period
120000
1
Active command to column command
(same bank)
Precharge to active command period
Write recovery or data-in to precharge lead
time
tRCD
tRP
20
20
15
—
—
—
ns
ns
ns
1
1
1
tDPL
Last data into active latency
tDAL
tRRD
tT
2CLK + 20ns
—
Active (a) to Active (b) command period
Transition time (rise and fall)
15
—
—
ns
ns
1
5.0
Refresh period
(4096 refresh cycles)
tREF
—
64
ms
Notes: 1. AC measurement assumes tT = 0.5ns. Reference level for timing of input signals is 1.4V.
2. Access time is measured at 1.4V. Load condition is CL = 30pF.
3. tLZ (min.) defines the time at which the outputs achieves the low impedance state.
4. tHZ (max.) defines the time at which the outputs achieves the high impedance state.
5. If tT ≥ 1ns, each parameters is changed as follows;
tAC, tOH, tLZ: should be added (tT (rise)/2 – 0.5)
tCH, tCL, tSI, tHI: should be added {(tT (rise) + tT (fall))/2 – 1}
Data Sheet E1164E20 (Ver. 2.0)
7
EDS1232AHTA-TI
Test Conditions
• AC high level voltage/low level input voltage: 2.4V/0.4V
• Input and output timing reference levels: 1.4V
• Input waveform and output load: See following figures
2.4 V
I/O
2.0 V
input
0.8 V
0.4 V
CL
t
T
tT
Input waveform and Output load
Data Sheet E1164E20 (Ver. 2.0)
8
EDS1232AHTA-TI
Relationship Between Frequency and Minimum Latency
Parameter
-75
133
7.5
Frequency (MHz)
100
10
tCK (ns)
Symbol
Unit
tCK
Notes
1
Active command to column command
(same bank)
Active command to active command
(same bank)
Active command to precharge command
(same bank)
Precharge command to active command
(same bank)
lRCD
3
9
6
3
2
2
7
5
2
2
lRC
tCK
tCK
tCK
tCK
1
1
1
1
lRAS
lRP
Write recovery or data-in to precharge command
(same bank)
lDPL
Active command to active command
lRRD
lSREX
lDAL
2
1
5
2
1
4
tCK
tCK
tCK
1
2
(different bank)
Self refresh exit time
Last data in to active command
(Auto precharge, same bank)
= [lRC]
3
Self refresh exit to command input
lSEC
9
7
tCK
Precharge command to high impedance
(CL = 2)
(CL = 3)
Last data out to active command
(Auto precharge, same bank)
lHZP
lHZP
lAPR
2
3
1
tCK
tCK
tCK
3
1
Last data out to precharge (early precharge)
(CL = 2)
lEP
–1
tCK
(CL = 3)
lEP
–2
1
–2
1
tCK
tCK
tCK
tCK
tCK
tCK
tCK
tCK
tCK
Column command to column command
Write command to data in latency
DQM to data in
lCCD
lWCD
lDID
0
0
0
0
DQM to data out
lDOD
lCLE
lMRD
lCDD
lPEC
2
2
CKE to CLK disable
1
1
Register set to active command
/CS to command disable
Power down exit to command input
2
2
0
0
1
1
Notes: 1. lRCD to lRRD are recommended value.
2. Be valid [DESL] or [NOP] at next command of self refresh exit.
3. Except [DESL] and [NOP]
Data Sheet E1164E20 (Ver. 2.0)
9
EDS1232AHTA-TI
Block Diagram
CLK
Clock
Generator
CKE
Bank 3
Bank 2
Bank 1
Row
Address
Address
Buffer
&
Refresh
Counter
Mode
Register
Bank 0
Sense Amplifier
DQM
DQ
/CS
Column Decoder &
Latch Circuit
Column
Address
Buffer
&
Burst
Counter
/RAS
/CAS
/WE
Data Control Circuit
Data Sheet E1164E20 (Ver. 2.0)
10
EDS1232AHTA-TI
Pin Function
CLK (input pin)
CLK is the master clock input. Other inputs signals are referenced to the CLK rising edge.
CKE (input pins)
CKE determine validity of the next CLK (clock). If CKE is high, the next CLK rising edge is valid; otherwise it is
invalid. If the CLK rising edge is invalid, the internal clock is not issued and the Synchronous DRAM suspends
operation.
When the Synchronous DRAM is not in burst mode and CKE is negated, the device enters power down mode.
During power down mode, CKE must remain low.
/CS (input pins)
/CS low starts the command input cycle. When /CS is high, commands are ignored but operations continue.
/RAS, /CAS, and /WE (input pins)
/RAS, /CAS and /WE have the same symbols on conventional DRAM but different functions. For details, refer to the
command table.
A0 to A11 (input pins)
Row address (AX0 to AX11) is determined by A0 to A11 at the bank active command cycle CLK rising edge.
Column address is determined by A0 to A7 (see Address Pins Table) at the read or write command cycle CLK rising
edge. And this column address becomes burst access start address.
[Address Pins Table]
Address (A0 to A11)
Part number
Row address
AX0 to AX11
Column address
AY0 to AY7
EDS1232AHTA
A10 defines the precharge mode. When A10 = High at the precharge command cycle, all banks are precharged.
But when A10 = Low at the precharge command cycle, only the bank that is selected by BA0 and BA1 (BS) is
precharged. For details refer to the command operation section.
BA0 and BA1 (input pin)
BA0 and BA1 are bank select signal. (See Bank Select Signal Table)
[Bank Select Signal Table]
BA0
L
BA1
L
Bank 0
Bank 1
H
L
Bank 2
L
H
Bank 3
H
H
Remark: H: VIH. L: VIL.
Data Sheet E1164E20 (Ver. 2.0)
11
EDS1232AHTA-TI
DQM0 to DQM3 (input pins)
DQM0 to DQM3 control input/output buffers.
In this datasheet, DQM represents DQM0 to DQM3.
Read operation: If DQM is High, the output buffer becomes High-Z. If the DQM is Low, the output buffer becomes
Low-Z. (The latency of DQM during reading is 2 clocks.)
Write operation: If DQM is High, the previous data is held (the new data is not written). If DQM is Low, the data is
written. (The latency of DQM during writing is 0 clock.)
Each DQM pin corresponds to eight DQ pins, respectively (See DQM Correspondence Table).
[DQM Correspondence Table]
Part number
Organization
Data mask
DQM0
DQs
EDS1232AHTA
× 32 bits
DQ0 to DQ7
DQ8 to DQ15
DQ16 to DQ23
DQ24 to DQ31
DQM1
DQM2
DQM3
DQ0 to DQ31 (input/output pins)
DQ pins have the same function as I/O pins on a conventional DRAM.
VDD, VSS, VDDQ, VSSQ (Power supply)
VDD and VSS are power supply pins for internal circuits. VDDQ and VSSQ are power supply pins for the output
buffers.
Data Sheet E1164E20 (Ver. 2.0)
12
EDS1232AHTA-TI
Command Operation
Command Truth Table
The SDRAM recognizes the following commands specified by the /CS, /RAS, /CAS, /WE and address pins.
CKE
A0 to
A11
Function
Symbol
DESL
NOP
n – 1
H
n
×
×
×
×
×
×
×
×
×
×
×
/CS
H
L
/RAS
×
/CAS
×
/WE
×
BA1
×
BA0
×
A10
×
Device deselect
No operation
×
×
×
V
V
V
V
V
×
×
V
H
H
H
H
H
H
H
L
H
H
L
H
L
×
×
×
Burst stop
BST
H
L
×
×
×
Read
READ
READA
WRIT
WRITA
ACT
H
L
H
H
L
V
V
V
V
V
V
×
V
V
V
V
V
V
×
L
Read with auto precharge
Write
H
L
L
H
L
H
L
L
Write with auto precharge
Bank activate
H
L
L
L
H
V
L
H
L
H
H
H
L
H
L
Precharge select bank
Precharge all banks
Mode register set
PRE
H
L
L
PALL
MRS
H
L
L
L
H
L
H
L
L
L
L
L
Remark: H: VIH. L: VIL. ×: VIH or VIL. V: Valid address input.
Device deselect command [DESL]
When this command is set (/CS is High), the SDRAM ignore command input at the clock. However, the internal
status is held.
No operation [NOP]
This command is not an execution command. However, the internal operations continue.
Burst stop command [BST]
This command can stop the current burst operation.
Column address strobe and read command [READ]
This command starts a read operation. In addition, the start address of burst read is determined by the column
address (see Address Pins Table in Pin Function) and the bank select address (BA0, BA1). After the read operation,
the output buffer becomes High-Z.
Read with auto-precharge [READA]
This command automatically performs a precharge operation after a burst read with a burst length of 1, 2, 4 or 8.
Column address strobe and write command [WRIT]
This command starts a write operation. When the burst write mode is selected, the column address (see Address
Pins Table in Pin Function) and the bank select address (BA0, BA1) become the burst write start address. When the
single write mode is selected, data is only written to the location specified by the column address (see Address Pins
Table in Pin Function) and the bank select address (BA0, BA1).
Write with auto-precharge [WRITA]
This command automatically performs a precharge operation after a burst write with a length of 1, 2, 4 or 8, or after a
single write operation.
Data Sheet E1164E20 (Ver. 2.0)
13
EDS1232AHTA-TI
Row address strobe and bank activate [ACT]
This command activates the bank that is selected by BA0, BA1 and determines the row address (A0 to A11). (See
Bank Select Signal Table)
Precharge selected bank [PRE]
This command starts precharge operation for the bank selected by BA0, BA1. (See Bank Select Signal Table)
[Bank Select Signal Table]
BA0
L
BA1
L
Bank 0
Bank 1
H
L
Bank 2
L
H
Bank 3
H
H
Remark: H: VIH. L: VIL.
Precharge all banks [PALL]
This command starts a precharge operation for all banks.
Refresh [REF/SELF]
This command starts the refresh operation. There are two types of refresh operation, the one is auto-refresh, and
the other is self-refresh. For details, refer to the CKE truth table section.
Mode register set [MRS]
The SDRAM has a mode register that defines how it operates. The mode register is specified by the address pins
(A0 to BA0 and BA1) at the mode register set cycle. For details, refer to the Mode Register Configuration. After
power on, the contents of the mode register are undefined, execute the mode register set command to set up the
mode register.
Data Sheet E1164E20 (Ver. 2.0)
14
EDS1232AHTA-TI
DQM Truth Table
CKE
n – 1
H
DQM
0
L
H
L
×
×
×
H
×
×
×
1
L
H
×
L
×
×
×
H
×
×
2
L
H
×
×
L
×
×
×
H
×
3
L
H
×
×
×
L
×
×
×
H
Function
Symbol
ENB
MASK
ENB0
n
×
×
×
×
×
×
×
×
×
×
Data write / output enable
Data mask / output disable
H
DQ0 to DQ7 write enable/output enable
DQ8 to DQ15 write enable/output enable
DQ16 to DQ23 write enable/output enable
DQ24 to DQ31 write enable/output enable
DQ0 to DQ7 write inhibit/output disable
DQ8 to DQ15 write inhibit/output disable
DQ16 to DQ23 write inhibit/output disable
DQ24 to DQ31 write inhibit/output disable
H
ENB1
H
ENB2
H
ENB3
H
MASK0
MASK 1
MASK 2
MASK 3
H
H
H
H
Remark: H: VIH. L: VIL. ×: VIH or VIL
Write: lDID is needed.
Read: lDOD is needed.
CKE Truth Table
CKE
Current state
Activating
Any
Function
Symbol
n – 1
H
L
n
L
L
/CS
×
/RAS
/CAS
×
/WE
×
Address
Clock suspend mode entry
Clock suspend mode
Clock suspend mode exit
×
×
×
L
L
H
×
H
×
×
H
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Clock suspend
Idle
L
H
H
L
×
×
×
CBR (auto) refresh command
Self refresh entry
REF
H
H
L
L
L
H
H
H
×
Idle
SELF
L
L
Self refresh
Self refresh exit
H
H
L
L
H
×
L
H
L
Idle
Power down entry
Power down exit
H
H
L
H
×
H
×
L
H
H
L
Power down
H
H
×
×
L
H
H
Remark: H: VIH. L: VIL. ×: VIH or VIL
Data Sheet E1164E20 (Ver. 2.0)
15
EDS1232AHTA-TI
Function Truth Table
The following table shows the operations that are performed when each command is issued in each mode of the
SDRAM.
The following table assumes that CKE is high.
Current state
Precharge
/CS
H
L
/RAS /CAS /WE
Address
Command
DESL
Operation
Enter IDLE after tRP
Enter IDLE after tRP
ILLEGAL
ILLEGAL*3
ILLEGAL*3
ILLEGAL*3
NOP*5
×
×
×
×
H
H
H
H
L
H
H
L
H
L
×
NOP
L
×
BST
L
H
L
BA, CA, A10
READ/READA
WRIT/WRITA
ACT
L
L
BA, CA, A10
L
H
H
L
H
L
BA, RA
L
L
BA, A10
PRE, PALL
REF, SELF
MRS
L
L
H
L
×
ILLEGAL
L
L
L
MODE
ILLEGAL
Idle
H
L
×
×
×
×
DESL
NOP
H
H
H
H
L
H
H
L
H
L
×
NOP
NOP
L
×
BST
ILLEGAL
L
H
L
BA, CA, A10
READ/READA
WRIT/WRITA
ACT
ILLEGAL*4
ILLEGAL*4
Bank and row active
NOP
L
L
BA, CA, A10
L
H
H
L
H
L
BA, RA
L
L
BA, A10
PRE, PALL
REF, SELF
MRS
L
L
H
L
×
Refresh
Mode register set*8
L
L
L
MODE
Row active
H
L
×
×
×
×
DESL
NOP
H
H
H
H
H
H
L
H
L
×
NOP
NOP
L
×
BST
ILLEGAL
L
H
L
BA, CA, A10
BA, CA, A10
READ/READA
WRIT/WRITA
Begin read*6
Begin write*6
L
L
Other bank active
L
L
H
H
BA, RA
ACT
ILLEGAL on same bank*2
L
L
L
H
L
L
L
H
L
L
H
L
BA, A10
PRE, PALL
REF, SELF
MRS
Precharge*7
L
×
ILLEGAL
L
L
MODE
ILLEGAL
×
H
H
×
×
H
L
×
×
×
DESL
Continue burst to end
Continue burst to end
Burst stop
Read
H
H
NOP
BST
Continue burst read to /CAS
latency and New read
Term burst read/start write
L
L
L
H
H
L
L
L
H
L
BA, CA, A10
BA, CA, A10
BA, RA
READ/READA
WRIT/WRITA
ACT
Other bank active
H
H
ILLEGAL on same bank*2
L
L
L
L
L
L
H
L
L
L
H
L
BA, A10
×
PRE, PALL
REF, SELF
MRS
Term burst read and Precharge
ILLEGAL
MODE
ILLEGAL
Data Sheet E1164E20 (Ver. 2.0)
16
EDS1232AHTA-TI
Current state
Read with auto-
precharge
/CS
H
/RAS /CAS /WE
Address
Command
DESL
Operation
Continue burst to end and
precharge
×
×
×
×
Continue burst to end and
precharge
L
H
H
H
×
NOP
L
L
L
H
H
H
H
L
L
L
H
L
×
BST
ILLEGAL
BA, CA, A10
BA, CA, A10
READ/READA
WRIT/WRITA
ILLEGAL*3
ILLEGAL*3
Other bank active
L
L
H
H
BA, RA
ACT
ILLEGAL on same bank*2
L
L
L
H
L
L
L
L
L
H
L
L
BA, A10
PRE, PALL
REF, SELF
MRS
ILLEGAL*3
L
H
L
×
ILLEGAL
L
L
MODE
ILLEGAL
Write
×
×
H
H
L
×
H
L
×
DESL
Continue burst to end
Continue burst to end
Burst stop
H
H
H
H
×
NOP
×
BST
H
L
BA, CA, A10
BA, CA, A10
READ/READA
WRIT/WRITA
Term burst and New read
Term burst and New write
L
Other bank active
L
L
H
H
BA, RA
ACT
ILLEGAL on same bank*3
L
L
L
L
L
L
H
L
L
L
H
L
BA, A10
×
PRE, PALL
REF, SELF
MRS
Term burst write and Precharge*1
ILLEGAL
ILLEGAL
MODE
Write with auto-
precharge
Continue burst to end and
H
L
×
×
×
×
×
DESL
NOP
precharge
Continue burst to end and
precharge
H
H
H
L
L
L
H
H
H
H
L
L
L
H
L
×
BST
ILLEGAL
BA, CA, A10
BA, CA, A10
READ/READA
WRIT/WRITA
ILLEGAL*3
ILLEGAL*3
Other bank active
L
L
H
H
BA, RA
ACT
ILLEGAL on same bank*3
L
L
L
H
L
L
L
L
L
L
L
L
L
L
H
L
L
BA, A10
PRE, PALL
REF, SELF
MRS
ILLEGAL*3
ILLEGAL
H
L
×
L
L
MODE
ILLEGAL
×
H
H
H
H
L
×
×
×
DESL
Enter IDLE after tRC
Enter IDLE after tRC
ILLEGAL
ILLEGAL*4
ILLEGAL*4
ILLEGAL*4
ILLEGAL*4
ILLEGAL
Refresh (auto-refresh)
H
H
L
H
L
×
NOP
×
BST
H
L
BA, CA, A10
BA, CA, A10
BA, RA
BA, A10
×
READ/READA
WRIT/WRITA
ACT
L
H
H
L
H
L
L
PRE, PALL
REF, SELF
MRS
L
H
L
L
L
MODE
ILLEGAL
Data Sheet E1164E20 (Ver. 2.0)
17
EDS1232AHTA-TI
Current state
/CS
H
L
/RAS /CAS /WE
Address
Command
DESL
Operation
NOP
Mode register set
×
×
×
×
H
H
H
H
L
H
H
L
H
L
×
NOP
NOP
L
×
BST
ILLEGAL
L
H
L
BA, CA, A10
BA, CA, A10
BA, RA
BA, A10
×
READ/READA
WRIT/WRITA
ACT
ILLEGAL*4
ILLEGAL*4
Bank and row active*9
NOP
L
L
L
H
H
L
H
L
L
L
PRE, PALL
REF, SELF
MRS
L
L
H
L
Refresh*9
Mode register set*8
L
L
L
MODE
Remark: H: VIH. L: VIL. ×: VIH or VIL
Notes: 1. An interval of tDPL is required between the final valid data input and the precharge command.
2. If tRRD is not satisfied, this operation is illegal.
3. Illegal for same bank, except for another bank.
4. Illegal for all banks.
5. NOP for same bank, except for another bank.
6. Illegal if tRCD is not satisfied.
7. Illegal if tRAS is not satisfied.
8. MRS command must be issued after DOUT finished, in case of DOUT remaining.
9. Illegal if lMRD is not satisfied.
Data Sheet E1164E20 (Ver. 2.0)
18
EDS1232AHTA-TI
Command Truth Table for CKE
CKE
Current State
Self refresh
n – 1 n
/CS /RAS /CAS /WE Address
Operation
Notes
H
L
×
×
H
L
L
L
×
H
L
L
L
H
L
L
L
×
H
L
×
H
L
L
L
L
H
L
L
L
L
×
×
×
×
×
×
×
×
×
×
H
H
L
×
×
H
H
L
×
H
H
L
×
×
H
×
×
H
L
L
L
×
H
L
L
L
×
×
×
×
×
×
×
×
×
×
H
L
×
×
×
H
L
×
×
H
L
×
×
×
H
×
×
×
H
L
L
×
×
H
L
L
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
H
×
×
×
×
H
L
×
×
×
H
L
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
INVALID, CLK (n – 1) would exit self refresh
Self refresh recovery
Self refresh recovery
ILLEGAL
H
H
H
H
L
L
L
L
ILLEGAL
L
Continue self refresh
Idle after tRC
Self refresh recovery
H
H
H
H
H
H
H
H
H
L
H
H
H
H
L
Idle after tRC
ILLEGAL
ILLEGAL
ILLEGAL
L
ILLEGAL
L
ILLEGAL
L
ILLEGAL
Power down
All banks idle
×
INVALID, CLK (n – 1) would exit power down
EXIT power down
H
H
L
×
×
×
L
EXIT power down
L
Continue power down mode
Refer to operations in Function Truth Table
Refer to operations in Function Truth Table
Refer to operations in Function Truth Table
CBR (auto) Refresh
H
H
H
H
H
H
H
H
H
H
L
H
H
H
H
H
L
×
OPCODE Refer to operations in Function Truth Table
Begin power down next cycle
L
Refer to operations in Function Truth Table
Refer to operations in Function Truth Table
L
L
×
Self refresh
1
L
OPCODE Refer to operations in Function Truth Table
H
L
×
×
×
×
Exit power down next cycle
Power down
L
1
1
2
Row active
H
L
×
Refer to operations in Function Truth Table
Clock suspend
×
Any state other than
listed above
H
H
L
H
L
Refer to operations in Function Truth Table
Begin clock suspend next cycle
Exit clock suspend next cycle
Maintain clock suspend
×
×
×
H
L
L
Remark: H: VIH. L: VIL. ×: VIH or VIL
Notes: 1. Self refresh can be entered only from the all banks idle state. Power down can be entered only from all
banks idle. Clock suspend can be entered only from following states, row active, read, read with auto-
precharge, write and write with auto precharge.
2. Must be legal command as defined in Function Truth Table.
Data Sheet E1164E20 (Ver. 2.0)
19
EDS1232AHTA-TI
Clock suspend mode entry
The SDRAM enters clock suspend mode from active mode by setting CKE to Low. If command is input in the clock
suspend mode entry cycle, the command is valid. The clock suspend mode changes depending on the current
status (1 clock before) as shown below.
ACTIVE clock suspend
This suspend mode ignores inputs after the next clock by internally maintaining the bank active status.
READ suspend and READ with Auto-precharge suspend
The data being output is held (and continues to be output).
WRITE suspend and WRIT with Auto-precharge suspend
In this mode, external signals are not accepted. However, the internal state is held.
Clock suspend
During clock suspend mode, keep the CKE to Low.
Clock suspend mode exit
The SDRAM exits from clock suspend mode by setting CKE to High during the clock suspend state.
IDLE
In this state, all banks are not selected, and completed precharge operation.
Auto-refresh command [REF]
When this command is input from the IDLE state, the SDRAM starts auto-refresh operation. (The auto-refresh is the
same as the CBR refresh of conventional DRAMs.) During the auto-refresh operation, refresh address and bank
select address are generated inside the SDRAM. For every auto-refresh cycle, the internal address counter is
updated. Accordingly, 4096 times are required to refresh the entire memory. Before executing the auto-refresh
command, all the banks must be in the IDLE state. In addition, since the precharge for all banks is automatically
performed after auto-refresh, no precharge command is required after auto-refresh.
Self-refresh entry [SELF]
When this command is input during the IDLE state, the SDRAM starts self-refresh operation. After the execution of
this command, self-refresh continues while CKE is Low. Since self-refresh is performed internally and automatically,
external refresh operations are unnecessary.
Power down mode entry
When this command is executed during the IDLE state, the SDRAM enters power down mode. In power down
mode, power consumption is suppressed by cutting off the initial input circuit.
Self-refresh exit
When this command is executed during self-refresh mode, the SDRAM can exit from self-refresh mode. After exiting
from self-refresh mode, the SDRAM enters the IDLE state.
Power down exit
When this command is executed at the power down mode, the SDRAM can exit from power down mode. After
exiting from power down mode, the SDRAM enters the IDLE state.
Data Sheet E1164E20 (Ver. 2.0)
20
EDS1232AHTA-TI
Simplified State Diagram
SELF
REFRESH
SR ENTRY
SR EXIT
*1
MRS
REFRESH
MODE
REGISTER
SET
AUTO
IDLE
REFRESH
CKE
CKE_
IDLE
POWER
DOWN
ACTIVE
ACTIVE
CLOCK
SUSPEND
CKE_
CKE
ROW
ACTIVE
BST
BST
WRITE
READ
Write
WRITE
WITH
AP
READ
WITH
AP
Read
CKE_
CKE_
CKE
WRITE
SUSPEND
READ
READ
SUSPEND
WRITE
READ
WRITE
CKE
READ
WITH AP
WRITE
WITH AP
WRITE
WITH AP
READ
WITH AP
PRECHARGE
CKE_
CKE_
WRITEA
SUSPEND
READA
SUSPEND
WRITEA
READA
CKE
CKE
PRECHARGE PRECHARGE
POWER
APPLIED
POWER
ON
PRECHARGE
PRECHARGE
Automatic transition after completion of command.
Transition resulting from command input.
Note: 1. After the auto-refresh operation, precharge operation is performed automatically and
enter the IDLE state.
Data Sheet E1164E20 (Ver. 2.0)
21
EDS1232AHTA-TI
Mode Register Configuration
Mode Register Set
The mode register is set by the input to the address pins (A0 to A11, BA0 and BA1) during mode register set cycles.
The mode register consists of five sections, each of which is assigned to address pins.
BA1, BA0, A8, A9, A10, A11: (OPCODE): The SDRAM has two types of write modes. One is the burst write mode,
and the other is the single write mode. These bits specify write mode.
Burst read and burst write: Burst write is performed for the specified burst length starting from the column address
specified in the write cycle.
Burst read and single write: Data is only written to the column address specified during the write cycle, regardless of
the burst length.
A7: Keep this bit Low at the mode register set cycle. If this pin is high, the vender test mode is set.
A6, A5, A4: (LMODE): These pins specify the /CAS latency.
A3: (BT): A burst type is specified.
A2, A1, A0: (BL): These pins specify the burst length.
BA1 BA0 A11 A10
OPCODE
A9
A8
A7
0
A6
A5
A4
A3
BT
A2
A1
BL
A0
LMODE
A6 A5 A4 CAS latency
A3 Burst type
Burst length
A2 A1 A0
0
0
0
0
1
0
0
1
1
X
0
1
0
1
X
R
R
2
0
1
Sequential
Interleave
BT=0 BT=1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
1
2
1
2
3
4
4
R
8
8
R
R
R
R
R
R
BA1 BA0 A11 A10 A9 A8
Write mode
R
0
0
0
1
Burst read and burst write
R
0
0
0
0
0
0
F.P.
X
X
F.P.: Full Page
R is Reserved (inhibit)
X: 0 or 1
0
0
0
1
1
0
0
1
0
1
X
X
X
X
X
X
X
X
X
X
1
1
0
1
Burst read and single write
R
R
R
R
X
X
X
X
X
X
Mode Register Set
Data Sheet E1164E20 (Ver. 2.0)
22
EDS1232AHTA-TI
Burst length = 2
Burst length = 4
Starting Ad. Addressing(decimal)
Starting Ad. Addressing(decimal)
A0
0
Sequential Interleave
A1
0
A0 Sequential
Interleave
0, 1,
1, 0,
0, 1,
1, 0,
0
1
0
1
0, 1, 2, 3,
1, 2, 3, 0,
2, 3, 0, 1,
0, 1, 2, 3,
1, 0, 3, 2,
2, 3, 0, 1,
3, 2, 1, 0,
1
0
1
1
3,
0, 1, 2,
Burst length = 8
Starting Ad.
Addressing(decimal)
A2 A1 A0 Sequential
Interleave
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0, 1, 2, 3, 4, 5, 6, 7,
1, 2, 3, 4, 5, 6, 7, 0,
2, 3, 4, 5, 6, 7, 0, 1,
3, 4, 5, 6, 7, 0, 1, 2,
4, 5, 6, 7, 0, 1, 2, 3,
5, 6, 7, 0, 1, 2, 3, 4,
6, 7, 0, 1, 2, 3, 4, 5,
7, 0, 1, 2, 3, 4, 5, 6,
0, 1, 2, 3, 4, 5, 6, 7,
1, 0, 3, 2, 5, 4, 7, 6,
2, 3, 0, 1, 6, 7, 4, 5,
3, 2, 1, 0, 7, 6, 5, 4,
4, 5, 6, 7, 0, 1, 2, 3,
5, 4, 7, 6, 1, 0, 3, 2,
6, 7, 4, 5, 2, 3, 0, 1,
7, 6, 5, 4, 3, 2, 1, 0,
Burst Sequence
Full page burst is available only for sequential addressing. The addressing sequence is started from the column
address that is asserted by read/write command. And the address is increased one by one.
It is back to the address 0 when the address reaches at the end of address 255. “Full page burst” stops the burst
read/write with burst stop command.
Data Sheet E1164E20 (Ver. 2.0)
23
EDS1232AHTA-TI
Power-up sequence
Power-up sequence
1. Apply VDD and VDDQ at the same time. Keep CKE low during power up.
2. Wait for stable power.
3. Start clock and drive CKE high.
Note: Voltage on any input pin must not exceed VDD + 0.3V during power up.
Initialization sequence
4. After stable power and stable clock, wait 200µs.
5. Issue precharge all command (PALL).
6. After tRP delay, issue 8 or more auto refresh commands (REF).
7. Set the mode register set command (MRS) to initialize the mode register.
Note: We recommend that you keep DQM and CKE high during initialization sequence to prevent data contention
on the DQ bus.
Power up sequence
Initialization sequence
0V
VDD, VDDQ
CKE
Low
CLK
lRP
lRC
lRC
lMRD
Command
PALL
REF
REF
MRS
CMD
Power stable
Clock stable
Power-up and Initialization sequence
Data Sheet E1164E20 (Ver. 2.0)
24
EDS1232AHTA-TI
Operation of the SDRAM
Read/Write Operations
Bank active
Before executing a read or write operation, the corresponding bank and the row address must be activated by the
bank active (ACT) command. An interval of tRCD is required between the bank active command input and the
following read/write command input.
Read operation
A read operation starts when a read command is input. Output buffer becomes Low-Z in the (/CAS Latency - 1)
cycle after read command set. The SDRAM can perform a burst read operation.
The burst length can be set to 1, 2, 4 and 8. The start address for a burst read is specified by the column address
and the bank select address at the read command set cycle. In a read operation, data output starts after the number
of clocks specified by the /CAS Latency. The /CAS Latency can be set to 2 or 3.
When the burst length is 1, 2, 4 and 8 the DOUT buffer automatically becomes High-Z at the next clock after the
successive burst-length data has been output.
The /CAS latency and burst length must be specified at the mode register.
CLK
tRCD
Command
Address
READ
ACT
Row
Column
out 3
out 1 out 2
out 0
out 1 out 2
CL = 2
CL = 3
DQ
out 3
out 0
CL = /CAS latency
Burst Length = 4
/CAS Latency
CLK
Command
Address
tRCD
ACT
Row
READ
Column
out 0
BL = 1
out 0 out 1
BL = 2
BL = 4
BL = 8
DQ
out 3
out 0 out 1 out 2
out 0 out 1 out 2
out 3
out 5 out 6 out 7
out 4
BL : Burst Length
/CAS Latency = 2
Burst Length
Data Sheet E1164E20 (Ver. 2.0)
25
EDS1232AHTA-TI
Write operation
Burst write or single write mode is selected by the OPCODE of the mode register.
1. Burst write: A burst write operation is enabled by setting OPCODE (A9, A8) to (0, 0). A burst write starts in the
same clock as a write command set. (The latency of data input is 0 clock.) The burst length can be set to 1, 2, 4
and 8, like burst read operations. The write start address is specified by the column address and the bank select
address at the write command set cycle.
CLK
tRCD
Command
Address
ACT
Row
WRIT
Column
in 0
in 0
BL = 1
in 1
in 1
in 1
BL = 2
BL = 4
BL = 8
DQ
in 3
in 0
in 0
in 2
in 2
in 5
in 6 in 7
in 3 in 4
CL = 2, 3
Burst write
2. Single write: A single write operation is enabled by setting OPCODE (A9, A8) to (1, 0). In a single write
operation, data is only written to the column address and the bank select address specified by the write
command set cycle without regard to the burst length setting. (The latency of data input is 0 clock).
CLK
tRCD
Command
WRIT
ACT
Row
Column
Address
DQ
in 0
Single write
Data Sheet E1164E20 (Ver. 2.0)
26
EDS1232AHTA-TI
Auto Precharge
Read with auto-precharge
In this operation, since precharge is automatically performed after completing a read operation, a precharge
command need not be executed after each read operation. The command executed for the same bank after the
execution of this command must be the bank active (ACT) command. In addition, an interval defined by lAPR is
required before execution of the next command.
[Clock cycle time]
/CAS latency
Precharge start cycle
3
2
2 cycle before the final data is output
1 cycle before the final data is output
CLK
CL=2 Command
ACT
READA
ACT
lRAS
DQ
out0
out1
out2
out3
lAPR
CL=3 Command
DQ
ACT
READA
ACT
lRAS
out0
out1
out2
out3
lAPR
Note: Internal auto-precharge starts at the timing indicated by " ".
And an interval of tRAS (
l
RAS) is required between previous active (ACT) command and internal precharge
"
".
Burst Read (BL = 4)
Write with auto-precharge
In this operation, since precharge is automatically performed after completing a burst write or single write operation,
a precharge command need not be executed after each write operation. The command executed for the same bank
after the execution of this command must be the bank active (ACT) command. In addition, an interval of lDAL is
required between the final valid data input and input of next command.
CLK
WRITA
ACT
ACT
Command
DQ
lRAS
in0 in1 in2 in3
lDAL
Note: Internal auto-precharge starts at the timing indicated by " ".
and an interval of tRAS (lRAS) is required between previous active (ACT) command
and internal precharge " ".
Burst Write (BL = 4)
Data Sheet E1164E20 (Ver. 2.0)
27
EDS1232AHTA-TI
CLK
WRITA
ACT
ACT
Command
lRAS
DQ
in
lDAL
Note: Internal auto-precharge starts at the timing indicated by " ".
and an interval of tRAS (lRAS) is required between previous active (ACT) command
and internal precharge " ".
Single Write
Data Sheet E1164E20 (Ver. 2.0)
28
EDS1232AHTA-TI
Burst Stop Command
During a read cycle, when the burst stop command is issued, the burst read data are terminated and the data bus
goes to High-Z after the /CAS latency from the burst stop command.
CLK
READ
BST
Command
High-Z
High-Z
DQ
out
out
out
out
out
(CL = 2)
DQ
(CL = 3)
out
Burst Stop at Read
During a write cycle, when the burst stop command is issued, the burst write data are terminated and data bus goes
to High-Z at the same clock with the burst stop command.
CLK
WRITE
in
BST
Command
DQ
High-Z
in
in
in
Burst Stop at Write
Data Sheet E1164E20 (Ver. 2.0)
29
EDS1232AHTA-TI
Command Intervals
Read command to Read command interval
1. Same bank, same ROW address: When another read command is executed at the same ROW address of the
same bank as the preceding read command execution, the second read can be performed after an interval of no
less than 1 clock. Even when the first command is a burst read that is not yet finished, the data read by the
second command will be valid.
CLK
Command
ACT
Row
READ
READ
Column A Column B
Address
BS
DQ
out A0
out B2 out B3
out B0 out B1
CL = 3
BL = 4
Bank 0
Column =B
Dout
Bank0
Active
Column =A Column =B Column =A
Read Read Dout
READ to READ Command Interval (same ROW address in same bank)
2. Same bank, different ROW address: When the ROW address changes on same bank, consecutive read
commands cannot be executed; it is necessary to separate the two read commands with a precharge command
and a bank active command.
3. Different bank: When the bank changes, the second read can be performed after an interval of no less than 1
clock, provided that the other bank is in the bank active state. Even when the first command is a burst read that
is not yet finished, the data read by the second command will be valid.
CLK
Command
READ READ
ACT
ACT
Column A
Row 1
Column B
Address
BS
Row 0
DQ
out A0
out B2 out B3
out B0 out B1
Bank3
Dout
Bank0
Dout
CL = 3
BL = 4
Bank0
Active
Bank3 Bank0 Bank3
Active Read Read
READ to READ Command Interval (different bank)
Data Sheet E1164E20 (Ver. 2.0)
30
EDS1232AHTA-TI
Write command to Write command interval
1. Same bank, same ROW address: When another write command is executed at the same ROW address of the
same bank as the preceding write command, the second write can be performed after an interval of no less than
1 clock. In the case of burst writes, the second write command has priority.
CLK
Command
Address
WRIT
ACT
Row
WRIT
Column B
Column A
BS
DQ
in A0
in B2 in B3
in B0 in B1
Bank0
Active
Column =A Column =B
Write Write
Burst Write Mode
BL = 4
Bank 0
WRITE to WRITE Command Interval (same ROW address in same bank)
2. Same bank, different ROW address: When the ROW address changes, consecutive write commands cannot be
executed; it is necessary to separate the two write commands with a precharge command and a bank active
command.
3. Different bank: When the bank changes, the second write can be performed after an interval of no less than 1
clock, provided that the other bank is in the bank active state. In the case of burst write, the second write
command has priority.
CLK
Command
Address
ACT
ACT WRIT WRIT
Column A
Row 1
Column B
Row 0
BS
DQ
in A0
in B2 in B3
in B0 in B1
Burst Write Mode
BL = 4
Bank0
Active
Bank3 Bank0 Bank3
Active Write Write
WRITE to WRITE Command Interval (different bank)
Data Sheet E1164E20 (Ver. 2.0)
31
EDS1232AHTA-TI
Read command to Write command interval
1. Same bank, same ROW address: When the write command is executed at the same ROW address of the same
bank as the preceding read command, the write command can be performed after an interval of no less than 1
clock. However, DQM must be set High so that the output buffer becomes High-Z before data input.
CLK
Command
READ WRIT
CL=2
DQM
CL=3
DQ (input)
DQ (output)
in B0
in B3
in B1 in B2
BL = 4
Burst write
High-Z
READ to WRITE Command Interval (1)
CLK
Command
DQM
READ
WRIT
2 clock
CL=2
out
out
out
out
out
in
in
in
in
in
in
in
in
DQ
CL=3
READ to WRITE Command Interval (2)
2. Same bank, different ROW address: When the ROW address changes, consecutive write commands cannot be
executed; it is necessary to separate the two commands with a precharge command and a bank active
command.
3. Different bank: When the bank changes, the write command can be performed after an interval of no less than 1
cycle, provided that the other bank is in the bank active state. However, DQM must be set High so that the
output buffer becomes High-Z before data input.
Data Sheet E1164E20 (Ver. 2.0)
32
EDS1232AHTA-TI
Write command to Read command interval:
1. Same bank, same ROW address: When the read command is executed at the same ROW address of the same
bank as the preceding write command, the read command can be performed after an interval of no less than 1
clock. However, in the case of a burst write, data will continue to be written until one clock before the read
command is executed.
CLK
Command
DQM
WRIT
in A0
READ
DQ (input)
DQ (output)
out B0
out B1
out B2
out B3
Burst Write Mode
CL = 2
Column = A
Write
/CAS Latency
Column = B
Read
Column = B
Dout
BL = 4
Bank 0
WRITE to READ Command Interval (1)
CLK
WRIT
in A0
READ
Command
DQM
DQ (input)
in A1
DQ (output)
out B0
out B1
out B2
out B3
Burst Write Mode
CL = 2
Column = A
Write
/CAS Latency
Column = B
Read
Column = B
Dout
BL = 4
Bank 0
WRITE to READ Command Interval (2)
2. Same bank, different ROW address: When the ROW address changes, consecutive read commands cannot be
executed; it is necessary to separate the two commands with a precharge command and a bank active
command.
3. Different bank: When the bank changes, the read command can be performed after an interval of no less than 1
clock, provided that the other bank is in the bank active state. However, in the case of a burst write, data will
continue to be written until one clock before the read command is executed (as in the case of the same bank and
the same address).
Data Sheet E1164E20 (Ver. 2.0)
33
EDS1232AHTA-TI
Read with auto precharge to Read command interval
1. Different bank: When some banks are in the active state, the second read command (another bank) is executed.
Even when the first read with auto-precharge is a burst read that is not yet finished, the data read by the second
command is valid. The internal auto-precharge of one bank starts at the next clock of the second command.
CLK
Command
BS
READA
READ
DQ
out A0
out A1
out B0
out B1
bank0
Read A
bank3
Read
CL= 3
BL = 4
Note: Internal auto-precharge starts at the timing indicated by "
".
Read with Auto Precharge to Read Command Interval (Different bank)
2. Same bank: The consecutive read command (the same bank) is illegal.
Write with auto precharge to Write command interval
1. Different bank: When some banks are in the active state, the second write command (another bank) is executed.
In the case of burst writes, the second write command has priority. The internal auto-precharge of one bank
starts 2 clocks later from the second command.
CLK
Command
BS
WRITA
in A0
WRIT
in B0
DQ
in A1
in B1
in B2
".
in B3
bank0
Write A
bank3
Write
BL= 4
Note: Internal auto-precharge starts at the timing indicated by "
Write with Auto Precharge to Write Command Interval (Different bank)
2. Same bank: The consecutive write command (the same bank) is illegal.
Data Sheet E1164E20 (Ver. 2.0)
34
EDS1232AHTA-TI
Read with auto precharge to Write command interval
1. Different bank: When some banks are in the active state, the second write command (another bank) is executed.
However, DQM must be set High so that the output buffer becomes High-Z before data input. The internal auto-
precharge of one bank starts at the next clock of the second command.
CLK
Command
BS
READA
WRIT
in B0
CL = 2
DQM
CL = 3
DQ (input)
in B1
in B2
in B3
DQ (output)
High-Z
BL = 4
bank0
ReadA
bank3
Write
Note: Internal auto-precharge starts at the timing indicated by "
".
Read with Auto Precharge to Write Command Interval (Different bank)
2. Same bank: The consecutive write command from read with auto precharge (the same bank) is illegal. It is
necessary to separate the two commands with a bank active command.
Write with auto precharge to Read command interval
1. Different bank: When some banks are in the active state, the second read command (another bank) is executed.
However, in case of a burst write, data will continue to be written until one clock before the read command is
executed. The internal auto-precharge of one bank starts at 2 clocks later from the second command.
CLK
Command
BS
WRITA
in A0
READ
DQM
DQ (input)
DQ (output)
out B0
out B1
out B2 out B3
CL = 3
BL = 4
bank0
WriteA
bank3
Read
Note: Internal auto-precharge starts at the timing indicated by "
".
Write with Auto Precharge to Read Command Interval (Different bank)
2. Same bank: The consecutive read command from write with auto precharge (the same bank) is illegal. It is
necessary to separate the two commands with a bank active command.
Data Sheet E1164E20 (Ver. 2.0)
35
EDS1232AHTA-TI
Read command to Precharge command interval (same bank)
When the precharge command is executed for the same bank as the read command that preceded it, the minimum
interval between the two commands is one clock. However, since the output buffer then becomes High-Z after the
clocks defined by lHZP, there is a case of interruption to burst read data output will be interrupted, if the precharge
command is input during burst read. To read all data by burst read, the clocks defined by lEP must be assured as
an interval from the final data output to precharge command execution.
CLK
PRE/PALL
out A2
READ
Command
DQ
out A0
out A1
out A3
CL=2
lEP = -1 cycle
READ to PRECHARGE Command Interval (same bank): To output all data (CL = 2, BL = 4)
CLK
PRE/PALL
out A1
READ
Command
DQ
out A0
out A2
out A3
CL=3
lEP = -2 cycle
READ to PRECHARGE Command Interval (same bank): To output all data (CL = 3, BL = 4)
CLK
PRE/PALL
READ
Command
High-Z
DQ
out A0
lHZP = 2
READ to PRECHARGE Command Interval (same bank): To stop output data (CL = 2, BL = 1, 2, 4, 8)
CLK
PRE/PALL
READ
Command
DQ
High-Z
out A0
lHZP =3
READ to PRECHARGE Command Interval (same bank): To stop output data (CL = 3, BL = 1, 2, 4, 8)
Data Sheet E1164E20 (Ver. 2.0)
36
EDS1232AHTA-TI
Write command to Precharge command interval (same bank)
When the precharge command is executed for the same bank as the write command that preceded it, the minimum
interval between the two commands is 1 clock. However, if the burst write operation is unfinished, the input data
must be masked by means of DQM for assurance of the clock defined by tDPL.
CLK
PRE/PALL
WRIT
in A0
Command
DQM
DQ
in A1
in A2
tDPL
WRITE to PRECHARGE Command Interval (same bank) (BL = 4 (To stop write operation))
CLK
PRE/PALL
Command
DQM
WRIT
in A0
DQ
in A1
in A2
in A3
tDPL
WRITE to PRECHARGE Command Interval (same bank) (BL = 4 (To write all data))
Data Sheet E1164E20 (Ver. 2.0)
37
EDS1232AHTA-TI
Bank active command interval
1. Same bank: The interval between the two bank active commands must be no less than tRC.
2. In the case of different bank active commands: The interval between the two bank active commands must be no
less than tRRD.
CLK
Command
Address
BS
ACT
ACT
ROW
ROW
tRC
Bank 0
Active
Bank 0
Active
Bank Active to Bank Active for Same Bank
CLK
Command
Address
ACT
ACT
ROW:0
ROW:1
BS
tRRD
Bank 0
Active
Bank 3
Active
Bank Active to Bank Active for Different Bank
Mode register set to Bank active command interval
The interval between setting the mode register and executing a bank active command must be no less than lMRD.
CLK
Command
Address
MRS
ACT
OPCODE
BS & ROW
lMRD
Mode
Register Set
Bank
Active
Mode register set to Bank active command interval
Data Sheet E1164E20 (Ver. 2.0)
38
EDS1232AHTA-TI
DQM Control
The DQM mask the DQ data. The timing of DQM is different during reading and writing.
Reading
When data is read, the output buffer can be controlled by DQM. By setting DQM to Low, the output buffer becomes
Low-Z, enabling data output. By setting DQM to High, the output buffer becomes High-Z, and the corresponding
data is not output. However, internal reading operations continue. The latency of DQM during reading is 2 clocks.
Writing
Input data can be masked by DQM. By setting DQM to Low, data can be written. In addition, when DQM are set to
High, the corresponding data is not written, and the previous data is held. The latency of DQM during writing is 0
clock.
CLK
DQM
High-Z
DQ
out 0
out 1
out 3
lDOD = 2 Latency
Reading
CLK
DQM
DQ
in 3
in 0
in 1
lDID = 0 Latency
Writing
Data Sheet E1164E20 (Ver. 2.0)
39
EDS1232AHTA-TI
Refresh
Auto-refresh
All the banks must be precharged before executing an auto-refresh command. Since the auto-refresh command
updates the internal counter every time it is executed and determines the banks and the ROW addresses to be
refreshed, external address specification is not required. The refresh cycles are required to refresh all the ROW
addresses within tREF (max.). The output buffer becomes High-Z after auto-refresh start. In addition, since a
precharge has been completed by an internal operation after the auto-refresh, an additional precharge operation by
the precharge command is not required.
Self-refresh
After executing a self-refresh command, the self-refresh operation continues while CKE is held Low. During self-
refresh operation, all ROW addresses are refreshed by the internal refresh timer. A self-refresh is terminated by a
self-refresh exit command. Before and after self-refresh mode, execute auto-refresh to all refresh addresses in or
within tREF (max.) period on the condition 1 and 2 below.
1. Enter self-refresh mode within time as below* after either burst refresh or distributed refresh at equal interval to
all refresh addresses are completed.
2. Start burst refresh or distributed refresh at equal interval to all refresh addresses within time as below*after
exiting from self-refresh mode.
Note: tREF (max.) / refresh cycles.
Others
Power-down mode
The SDRAM enters power-down mode when CKE goes Low in the IDLE state. In power down mode, power
consumption is suppressed by deactivating the input initial circuit. Power down mode continues while CKE is held
Low. In addition, by setting CKE to High, the SDRAM exits from the power down mode, and command input is
enabled from the next clock. In this mode, internal refresh is not performed.
Clock suspend mode
By driving CKE to Low during a bank active or read/write operation, the SDRAM enters clock suspend mode. During
clock suspend mode, external input signals are ignored and the internal state is maintained. When CKE is driven
High, the SDRAM terminates clock suspend mode, and command input is enabled from the next clock. For details,
refer to the "CKE Truth Table".
Data Sheet E1164E20 (Ver. 2.0)
40
EDS1232AHTA-TI
Timing Waveforms
Read Cycle
tCK
tCH tCL
CLK
tRC
VIH
CKE
t
tRAS
RP
tRCD
tHI
tSI
tSI tHI
tSI tHI
tSI tHI
tSI tHI
/CS
tSI tHI
tSI tHI
tSI tHI
tSI tHI
tSI tHI
tSI tHI
/RAS
tSI tHI
tSI tHI
/CAS
tSI tHI
tSI tHI
tSI tHI
tSI tHI
/WE
BS
tSI tHI
tSI tHI
tSI tHI
tSI tHI
tSI tHI
tSI tHI
tSI tHI
tSI tHI
A10
Address
DQM
tSI tHI
tSI tHI
tSI
tHI
DQ (input)
t
t
t
t
HZ
AC
AC
AC
DQ (output)
t
AC
t
t
OH
t
OH
OH
t
OH
/CAS latency = 2
Burst length = 4
Bank 0 access
= VIH or VIL
Bank 0
Read
tLZ
Bank 0
Active
Bank 0
Precharge
= VOH or VOL
Data Sheet E1164E20 (Ver. 2.0)
41
EDS1232AHTA-TI
Write Cycle
tCK
tCH tCL
CLK
tRC
VIH
CKE
tRP
tRAS
tRCD
tSI tHI
tSI tHI
tSI tHI
tSI tHI
tSI tHI
/CS
tSI tHI
tSI tHI
tSI tHI
tSI tHI
tSI tHI
tSI tHI
/RAS
tSI tHI
/CAS
/WE
tSI tHI
tSI tHI
tSI tHI
tSI tHI
tSI tHI
tSI tHI
tSI tHI
tSI tHI
tSI tHI
tSI tHI
BS
tSI tHI
tSI tHI
tSI tHI
A10
tSI tHI
tSI tHI
Address
DQM
tSI
tHI
tSI tHI tSI tHI tSI tHI tSI tHI
DQ (input)
tDPL
DQ (output)
Bank 0
Precharge
Bank 0
Write
CL = 2
BL = 4
Bank 0
Active
Bank 0 access
= VIH or VIL
Mode Register Set Cycle
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CLK
VIH
CKE
/CS
/RAS
/CAS
/WE
BS
code
C: b’
Address
DQM
valid
C: b
R: b
b
b+3
b’ b’+1 b’+2 b’+3
DQ (output)
DQ (input)
High-Z
lMRD
lRP
lRCD
Output mask
lRCD = 3
Precharge
If needed
Mode
register
Set
Bank 3
Active
Bank 3
Read
/CAS latency = 3
Burst length = 4
= VIH or VIL
Data Sheet E1164E20 (Ver. 2.0)
42
EDS1232AHTA-TI
Read Cycle/Write Cycle
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20
CLK
CKE
VIH
Read cycle
/RAS-/CAS delay = 3
/CAS latency = 3
Burst length = 4
/CS
/RAS
=
VIH or VIL
/CAS
/WE
BS
Address
DQM
R:a
C:a
R:b
C:b
C:b'
C:b"
DQ (output)
DQ (input)
a
a+1 a+2 a+3
b
b+1 b+2 b+3 b' b'+1 b" b"+1 b"+2 b"+3
High-Z
Bank 0
Active
Bank 0
Read
Bank 3
Active
Bank 3 Bank 0
Bank 3
Read
Bank 3
Read
Bank 3
Precharge
Read
Precharge
VIH
CKE
Write cycle
/RAS-/CAS delay = 3
/CAS latency = 3
Burst length = 4
= VIH or VIL
/CS
/RAS
/CAS
/WE
BS
Address
DQM
R:a
C:a
a
R:b
C:b
C:b'
C:b"
High-Z
DQ (output)
DQ (input)
a+1 a+2 a+3
b
b+1 b+2 b+3 b'
b'+1 b" b"+1b"+2 b"+3
Bank 0
Active
Bank 0
Write
Bank 3
Active
Bank 3
Write
Bank 0
Precharge
Bank 3
Write
Bank 3
Write
Bank 3
Precharge
Read/Single Write Cycle
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20
CLK
V
IH
CKE
/CS
/RAS
/CAS
/WE
BS
R:a
C:a
R:b
C:a' C:a
a
Address
DQM
DQ (input)
DQ (output)
a
a+1 a+2 a+3
a
a+1 a+2 a+3
Bank 0
Active
Bank 0
Read
Bank 3
Active
Bank 0 Bank 0
Write Read
Bank 0
Precharge
Bank 3
Precharge
V
IH
CKE
/CS
/RAS
/CAS
/WE
BS
R:a
C:a
R:b
C:a
C:b C:c
Address
DQM
a
b
c
DQ (input)
DQ (output)
a
a+1
a+3
Bank 0
Active
Bank 0
Read
Bank 0
Write
Bank 0 Bank 0
Write Write
Bank 0
Precharge
Bank 3
Active
Read/Single write
/RAS-/CAS delay = 3
/CAS latency = 3
Burst length = 4
=
VIH or VIL
Data Sheet E1164E20 (Ver. 2.0)
43
EDS1232AHTA-TI
Read/Burst Write Cycle
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20
CLK
CKE
/CS
/RAS
/CAS
/WE
BS
Address
DQM
R:a
C:a
R:b
C:a'
a
a+1 a+2 a+3
DQ (input)
DQ (output)
a
a+1 a+2 a+3
Bank 0
Active
Bank 0
Read
Bank 3
Active
Clock
suspend
Bank 0
Precharge
Bank 3
Precharge
Bank 0
Write
VIH
CKE
/CS
/RAS
/CAS
/WE
BS
R:a
C:a
R:b
C:a
a
Address
DQM
DQ (input)
DQ (output)
a+1 a+2 a+3
a
a+1
a+3
Bank 0
Active
Bank 0
Read
Bank 0
Write
Bank 0
Precharge
Bank 3
Active
Read/Burst write
/RAS-/CAS delay = 3
/CAS latency = 3
Burst length = 4
= VIH or VIL
Auto Refresh Cycle
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CLK
CKE
/CS
VIH
/RAS
/CAS
/WE
BS
Address
C:a
A10=1
R:a
DQM
DQ (input)
a
a+1
High-Z
DQ (output)
t
t
t
RC
RP
RC
Refresh cycle and
Read cycle
Active
Bank 0
Read
Bank 0
Auto Refresh
Precharge
If needed
Auto Refresh
/RAS-/CAS delay = 2
/CAS latency = 2
Burst length = 4
= VIH or VIL
Data Sheet E1164E20 (Ver. 2.0)
44
EDS1232AHTA-TI
Self Refresh Cycle
CLK
CKE
/CS
lSREX
CKE Low
/RAS
/CAS
/WE
BS
Address
DQM
A10=1
DQ (input)
High-Z
DQ (output)
t
RC
t
t
RC
RP
Self refresh cycle
/RAS-/CAS delay = 3
CL = 3
Auto
refresh
Self refresh entry
command
Precharge command
If needed
Next
Self refresh exit
ignore command
or No operation
Next
clock
enable
Self refresh entry
command
clock
enable
BL = 4
=
VIH or VIL
Clock Suspend Mode
tSI
tSI
10 11 12 13 14 15 16 17 18 19 20
tHI
8
0
1
2
3
4
5
6
7
9
CLK
CKE
Read cycle
/RAS-/CAS delay = 2
/CAS latency = 2
Burst length = 4
= VIH or VIL
/CS
/RAS
/CAS
/WE
BS
Address
R:a
C:a
R:b
C:b
DQM
DQ (output)
DQ (input)
a
a+1 a+2
a+3
b
b+1 b+2 b+3
High-Z
Bank0 Active clock
Active suspend start
Active clock Bank0
suspend end Read
Bank3 Read suspend Read suspend
Bank0
Earliest Bank3
Precharge
Bank3
Active
start
end Read Precharge
CKE
Write cycle
/RAS-/CAS delay = 2
/CAS latency = 2
Burst length = 4
= VIH or VIL
/CS
/RAS
/CAS
/WE
BS
R:b
a+1
Address
DQM
R:a
C:a
a
C:b
High-Z
DQ (output)
DQ (input)
a+2
a+3
b
b+1 b+2 b+3
Bank0
Active clock Bank0 Bank3 Write suspend Write suspend Bank3
Earliest Bank3
Precharge
Bank0 Active clock
Active suspend start
Precharge
end Write
supend end Write Active
start
Data Sheet E1164E20 (Ver. 2.0)
45
EDS1232AHTA-TI
Power Down Mode
CLK
CKE
/CS
CKE Low
/RAS
/CAS
/WE
BS
Address
DQM
A10=1
R: a
DQ (input)
High-Z
DQ (output)
tRP
Power down cycle
Power down entry
Power down
mode exit
Active Bank 0
Precharge command
If needed
/RAS-/CAS delay = 3
/CAS latency = 3
Burst length = 4
= VIH or VIL
Initialization Sequence
53
0
1
2
3
4
5
6
7
8
9
10
48
49
50
51
52
54
55
CLK
CKE
/CS
VIH
/RAS
/CAS
/WE
code
valid
Address
Valid
V
IH
DQM
DQ
High-Z
lMRD
t
t
RC
tRP
RC
Bank active
If needed
All banks
Precharge
Mode register
Set
Auto Refresh
Auto Refresh
Data Sheet E1164E20 (Ver. 2.0)
46
EDS1232AHTA-TI
Package Drawing
86-pin Plastic TSOP(ll)
Solder plating: Lead free (Sn-Bi)
Unit: mm
*1
22.22 ± 0.10
A
86
44
PIN#1 ID
1
43
A
B
0.50
0.10
0.17 to 0.27
0.81 max.
M S
B
0.80
Nom
0.25
0 to 8°
S
S
0.10
0.50 ± 0.15
Note: 1. This dimension does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or
gate burrs shall not exceed 0.15mm per side.
ECA-TS2-0117-02
Data Sheet E1164E20 (Ver. 2.0)
47
EDS1232AHTA-TI
Recommended Soldering Conditions
Please consult with our sales offices for soldering conditions of the EDS1232AHTA.
Type of Surface Mount Device
EDS1232AHTA: 86-pin Plastic TSOP(ll) < Lead free (Sn-Bi) >
Data Sheet E1164E20 (Ver. 2.0)
48
EDS1232AHTA-TI
NOTES FOR CMOS DEVICES
PRECAUTION AGAINST ESD FOR MOS DEVICES
1
Exposing the MOS devices to a strong electric field can cause destruction of the gate
oxide and ultimately degrade the MOS devices operation. Steps must be taken to stop
generation of static electricity as much as possible, and quickly dissipate it, when once
it has occurred. Environmental control must be adequate. When it is dry, humidifier
should be used. It is recommended to avoid using insulators that easily build static
electricity. MOS devices must be stored and transported in an anti-static container,
static shielding bag or conductive material. All test and measurement tools including
work bench and floor should be grounded. The operator should be grounded using
wrist strap. MOS devices must not be touched with bare hands. Similar precautions
need to be taken for PW boards with semiconductor MOS devices on it.
2
HANDLING OF UNUSED INPUT PINS FOR CMOS DEVICES
No connection for CMOS devices input pins can be a cause of malfunction. If no
connection is provided to the input pins, it is possible that an internal input level may be
generated due to noise, etc., hence causing malfunction. CMOS devices behave
differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed
high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected
to VDD or GND with a resistor, if it is considered to have a possibility of being an output
pin. The unused pins must be handled in accordance with the related specifications.
3
STATUS BEFORE INITIALIZATION OF MOS DEVICES
Power-on does not necessarily define initial status of MOS devices. Production process
of MOS does not define the initial operation status of the device. Immediately after the
power source is turned ON, the MOS devices with reset function have not yet been
initialized. Hence, power-on does not guarantee output pin levels, I/O settings or
contents of registers. MOS devices are not initialized until the reset signal is received.
Reset operation must be executed immediately after power-on for MOS devices having
reset function.
CME0107
Data Sheet E1164E20 (Ver. 2.0)
49
EDS1232AHTA-TI
The information in this document is subject to change without notice. Before using this document, confirm that this is the latest version.
No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of Elpida Memory, Inc.
Elpida Memory, Inc. does not assume any liability for infringement of any intellectual property rights
(including but not limited to patents, copyrights, and circuit layout licenses) of Elpida Memory, Inc. or
third parties by or arising from the use of the products or information listed in this document. No license,
express, implied or otherwise, is granted under any patents, copyrights or other intellectual property
rights of Elpida Memory, Inc. or others.
Descriptions of circuits, software and other related information in this document are provided for
illustrative purposes in semiconductor product operation and application examples. The incorporation of
these circuits, software and information in the design of the customer's equipment shall be done under
the full responsibility of the customer. Elpida Memory, Inc. assumes no responsibility for any losses
incurred by customers or third parties arising from the use of these circuits, software and information.
[Product applications]
Be aware that this product is for use in typical electronic equipment for general-purpose applications.
Elpida Memory, Inc. makes every attempt to ensure that its products are of high quality and reliability.
However, users are instructed to contact Elpida Memory's sales office before using the product in
aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment,
medical equipment for life support, or other such application in which especially high quality and
reliability is demanded or where its failure or malfunction may directly threaten human life or cause risk
of bodily injury.
[Product usage]
Design your application so that the product is used within the ranges and conditions guaranteed by
Elpida Memory, Inc., including the maximum ratings, operating supply voltage range, heat radiation
characteristics, installation conditions and other related characteristics. Elpida Memory, Inc. bears no
responsibility for failure or damage when the product is used beyond the guaranteed ranges and
conditions. Even within the guaranteed ranges and conditions, consider normally foreseeable failure
rates or failure modes in semiconductor devices and employ systemic measures such as fail-safes, so
that the equipment incorporating Elpida Memory, Inc. products does not cause bodily injury, fire or other
consequential damage due to the operation of the Elpida Memory, Inc. product.
[Usage environment]
Usage in environments with special characteristics as listed below was not considered in the design.
Accordingly, our company assumes no responsibility for loss of a customer or a third party when used in
environments with the special characteristics listed below.
Example:
1) Usage in liquids, including water, oils, chemicals and organic solvents.
2) Usage in exposure to direct sunlight or the outdoors, or in dusty places.
3) Usage involving exposure to significant amounts of corrosive gas, including sea air, CL2, H2S, NH3,
SO2, and NO .
x
4) Usage in environments with static electricity, or strong electromagnetic waves or radiation.
5) Usage in places where dew forms.
6) Usage in environments with mechanical vibration, impact, or stress.
7) Usage near heating elements, igniters, or flammable items.
If you export the products or technology described in this document that are controlled by the Foreign
Exchange and Foreign Trade Law of Japan, you must follow the necessary procedures in accordance
with the relevant laws and regulations of Japan. Also, if you export products/technology controlled by
U.S. export control regulations, or another country's export control laws or regulations, you must follow
the necessary procedures in accordance with such laws or regulations.
If these products/technology are sold, leased, or transferred to a third party, or a third party is granted
license to use these products, that third party must be made aware that they are responsible for
compliance with the relevant laws and regulations.
M01E0706
Data Sheet E1164E20 (Ver. 2.0)
50
相关型号:
©2020 ICPDF网 联系我们和版权申明