HM5225165B-A6 [ELPIDA]
256M LVTTL interface SDRAM 133 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank /16-Mword 】 4-bit 】 4-bank PC/133, PC/100 SDRAM; LVTTL 256M SDRAM接口的133 MHz / 100 MHz的4 Mword 】 16位】 4银行/ 8 - Mword 】 8位】 4银行/ 16 Mword 】 4位】 4银行PC / 133 ， PC / 100 SDRAM
| 型号： | HM5225165B-A6 |
| 厂家： | 
ELPIDA MEMORY |
| 描述： | 256M LVTTL interface SDRAM 133 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank /16-Mword 】 4-bit 】 4-bank PC/133, PC/100 SDRAM |
| 文件： | 总63页 (文件大小：454K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HM5225165B-75/A6/B6
HM5225805B-75/A6/B6
HM5225405B-75/A6/B6
256M LVTTL interface SDRAM
133 MHz/100 MHz
4-Mword × 16-bit × 4-bank/8-Mword × 8-bit × 4-bank
/16-Mword × 4-bit × 4-bank
PC/133, PC/100 SDRAM
E0082H10 (1st edition)
(Previous ADE-203-1073B (Z))
Jan. 31, 2001
Description
The HM5225165B is a 256-Mbit SDRAM organized as 4194304-word × 16-bit × 4 bank. The HM5225805B
is a 256-Mbit SDRAM organized as 8388608-word × 8-bit × 4 bank. The HM5225405B is a 256-Mbit
SDRAM organized as 16777216-word × 4-bit × 4 bank. All inputs and outputs are referred to the rising edge
of the clock input. It is packaged in standard 54-pin plastic TSOP II.
Features
•
•
•
•
•
•
•
•
3.3 V power supply
Clock frequency: 133 MHz/100 MHz (max)
LVTTL interface
Single pulsed RAS
4 banks can operate simultaneously and independently
Burst read/write operation and burst read/single write operation capability
Programmable burst length: 1/2/4/8
2 variations of burst sequence
Sequential (BL = 1/2/4/8)
Interleave (BL = 1/2/4/8)
•
Programmable CAS latency: 2/3
Elpida Memory, Inc. is a joint venture DRAM company of NEC Corporation and Hitachi, Ltd.
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
•
Byte control by DQM : DQM (HM5225805B/HM5225405B)
: DQMU/DQML (HM5225165B)
Refresh cycles: 8192 refresh cycles/64 ms
2 variations of refresh
•
•
Auto refresh
Self refresh
Ordering Information
Type No.
Frequency
CAS latency
Package
HM5225165BTT-75*1
HM5225165BTT-A6
HM5225165BTT-B6*2
133 MHz
100 MHz
100 MHz
3
2/3
3
400-mil 54-pin plastic TSOP II (TTP-54D)
HM5225165BLTT-75*1
HM5225165BLTT-A6
HM5225165BLTT-B6*2
133 MHz
100 MHz
100 MHz
3
2/3
3
HM5225805BTT-75*1
HM5225805BTT-A6
HM5225805BTT-B6*2
133 MHz
100 MHz
100 MHz
3
2/3
3
HM5225805BLTT-75*1
HM5225805BLTT-A6
HM5225805BLTT-B6*2
133 MHz
100 MHz
100 MHz
3
2/3
3
HM5225405BTT-75*1
HM5225405BTT-A6
HM5225405BTT-B6*2
133 MHz
100 MHz
100 MHz
3
2/3
3
HM5225405BLTT-75*1
HM5225405BLTT-A6
HM5225405BLTT-B6*2
133 MHz
100 MHz
100 MHz
3
2/3
3
Notes: 1. 100 MHz operation at CAS latency = 2.
2. 66 MHz operation at CAS latency = 2.
Data Sheet E0082H10
2
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Pin Arrangement (HM5225165B)
54-pin TSOP
1
VCC
54 VSS
2
DQ0
53 DQ15
3
4
5
V
CCQ
DQ1
DQ2
52
VSSQ
51 DQ14
50 DQ13
6
7
8
VSS
Q
DQ3
DQ4
49 VCC
Q
48 DQ12
47 DQ11
9
VCC
Q
DQ5
DQ6
46 VSS
Q
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
45 DQ10
44 DQ9
VSS
Q
DQ7
VCC
DQML
WE
43 VCC
Q
42 DQ8
41 VSS
40 NC
39 DQMU
38 CLK
37 CKE
36 A12
35 A11
34 A9
CAS
RAS
CS
BA0
BA1
A10
A0
A1
A2
A3
VCC
33 A8
32 A7
31 A6
30 A5
29 A4
28 VSS
(Top view)
Pin Description
Pin name
Function
Pin name
Function
A0 to A12,
BA0, BA1
Address input
WE
Write enable
Row address
A0 to A12
A0 to A8
DQMU/DQML Input/output mask
Column address
CLK
Clock input
Bank select address BA0/BA1 (BS) CKE
Clock enable
DQ0 to DQ15 Data-input/output
VCC
Power for internal circuit
Ground for internal circuit
Power for DQ circuit
Ground for DQ circuit
No connection
CS
Chip select
VSS
RAS
CAS
Row address strobe command
Column address strobe command
VCCQ
VSSQ
NC
Data Sheet E0082H10
3
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Pin Arrangement (HM5225805B)
54-pin TSOP
1
2
VCC
DQ0
54 VSS
53 DQ7
3
4
V
CCQ
NC
52
VSSQ
51 NC
5
DQ1
50 DQ6
6
7
8
V
SSQ
NC
49 VCC
48 NC
47 DQ5
Q
DQ2
9
VCCQ
46
VSSQ
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
NC
DQ3
SSQ
NC
45 NC
44 DQ4
V
43
VCCQ
42 NC
41 VSS
40 NC
39 DQM
38 CLK
37 CKE
36 A12
35 A11
34 A9
33 A8
32 A7
31 A6
30 A5
29 A4
28 VSS
VCC
NC
WE
CAS
RAS
CS
BA0
BA1
A10
A0
A1
A2
A3
VCC
(Top view)
Pin Description
Pin name
Function
Pin name
Function
A0 to A12,
BA0, BA1
Address input
WE
Write enable
Row address
A0 to A12
A0 to A9
DQM
CLK
Input/output mask
Clock input
Column address
Bank select address BA0/BA1 (BS) CKE
Clock enable
DQ0 to DQ7
CS
Data-input/output
VCC
Power for internal circuit
Ground for internal circuit
Power for DQ circuit
Ground for DQ circuit
No connection
Chip select
VSS
RAS
Row address strobe command
Column address strobe command
VCCQ
VSSQ
NC
CAS
Data Sheet E0082H10
4
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Pin Arrangement (HM5225405B)
54-pin TSOP
1
2
VCC
NC
54 VSS
53 NC
3
4
V
CCQ
NC
52
VSSQ
51 NC
5
DQ0
50 DQ3
6
VSSQ
49
VCCQ
7
8
NC
NC
48 NC
47 NC
9
VCCQ
46
VSSQ
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
NC
DQ1
SSQ
NC
45 NC
44 DQ2
V
43
VCCQ
42 NC
41 VSS
40 NC
39 DQM
38 CLK
37 CKE
36 A12
35 A11
34 A9
33 A8
32 A7
31 A6
30 A5
29 A4
28 VSS
VCC
NC
WE
CAS
RAS
CS
BA0
BA1
A10
A0
A1
A2
A3
VCC
(Top view)
Pin Description
Pin name
Function
Pin name
Function
A0 to A12,
BA0, BA1
Address input
WE
Write enable
Row address
A0 to A12
DQM
CLK
Input/output mask
Clock input
Column address
A0 to A9, A11
Bank select address BA0/BA1 (BS) CKE
Clock enable
DQ0 to DQ3
CS
Data-input/output
VCC
Power for internal circuit
Ground for internal circuit
Power for DQ circuit
Ground for DQ circuit
No connection
Chip select
VSS
RAS
Row address strobe command
Column address strobe command
VCCQ
VSSQ
NC
CAS
Data Sheet E0082H10
5
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Block Diagram (HM5225165B)
A0 to A12, BA0, BA1
A0 to A12, BA0, BA1
A0 to A8
Refresh
counter
Column address
counter
Column address
buffer
Row address
buffer
Row decoder
Row decoder
Row decoder
Row decoder
Memory array
Bank 0
Memory array
Bank 1
Memory array
Bank 2
Memory array
Bank 3
8192 row
8192 row
8192 row
8192 row
X 512 column
X 16 bit
X 512 column
X 16 bit
X 512 column
X 16 bit
X 512 column
X 16 bit
Control logic &
timing generator
Input
buffer
Output
buffer
DQ0 to DQ15
Data Sheet E0082H10
6
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Block Diagram (HM5225805B)
A0 to A12, BA0, BA1
A0 to A12, BA0, BA1
A0 to A9
Refresh
counter
Column address
counter
Column address
buffer
Row address
buffer
Row decoder
Row decoder
Row decoder
Row decoder
Memory array
Bank 0
Memory array
Bank 1
Memory array
Bank 2
Memory array
Bank 3
8192 row
8192 row
8192 row
8192 row
X 1024 column
X 8 bit
X 1024 column
X 8 bit
X 1024 column
X 8 bit
X 1024 column
X 8 bit
Control logic &
timing generator
Input
buffer
Output
buffer
DQ0 to DQ7
Data Sheet E0082H10
7
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Block Diagram (HM5225405B)
A0 to A12, BA0, BA1
A0 to A12, BA0, BA1
A0 to A9, A11
Refresh
counter
Column address
counter
Column address
buffer
Row address
buffer
Row decoder
Row decoder
Row decoder
Row decoder
Memory array
Bank 0
Memory array
Bank 1
Memory array
Bank 2
Memory array
Bank 3
8192 row
8192 row
8192 row
8192 row
X 2048 column
X 4 bit
X 2048 column
X 4 bit
X 2048 column
X 4 bit
X 2048 column
X 4 bit
Control logic &
timing generator
Input
buffer
Output
buffer
DQ0 to DQ3
Data Sheet E0082H10
8
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Pin Functions
CLK (input pin): CLK is the master clock input to this pin. The other input signals are referred at CLK
rising edge.
CS (input pin): When CS is Low, the command input cycle becomes valid. When CS is High, all inputs are
ignored. However, internal operations (bank active, burst operations, etc.) are held.
RAS, CAS, and WE (input pins): Although these pin names are the same as those of conventional DRAMs,
they function in a different way. These pins define operation commands (read, write, etc.) depending on the
combination of their voltage levels. For details, refer to the command operation section.
A0 to A12 (input pins): Row address (AX0 to AX12) is determined by A0 to A12 level at the bank active
command cycle CLK rising edge. Column address (AY0 to AY8; HM5225165B, AY0 to AY9;
HM5225805B, AY0 to AY9, AY11; HM5225405B) is determined by A0 to A8, A9 or A11 (A8;
HM5225165B, A9; HM5225805B, A9, A11; HM5225405B) level at the read or write command cycle CLK
rising edge. And this column address becomes burst access start address. A10 defines the precharge mode.
When A10 = High at the precharge command cycle, all banks are precharged. But when A10 = Low at the
precharge command cycle, only the bank that is selected by BA0/BA1 (BS) is precharged. For details refer to
the command operation section.
BA0/BA1 (input pin): BA0/BA1 are bank select signal (BS). The memory array of the HM5225165B,
HM5225805B, the HM5225405B is divided into bank 0, bank 1, bank 2 and bank 3. HM5225165B contain
8192-row × 512-column × 16-bit. HM5225805B contain 8192-row × 1024-column× 8-bit. HM5225405B
contain 8192-row × 2048-column × 4-bit. If BA0 is Low and BA1 is Low, bank 0 is selected. If BA0 is Low
and BA1 is High, bank 1 is selected. If BA0 is High and BA1 is Low, bank 2 is selected. If BA0 is High and
BA1 is High, bank 3 is selected.
CKE (input pin): This pin determines whether or not the next CLK is valid. If CKE is High, the next CLK
rising edge is valid. If CKE is Low, the next CLK rising edge is invalid. This pin is used for power-down
mode, clock suspend mode and self refresh mode.
DQM, DQMU/DQML (input pins): DQM, DQMU/DQML controls input/output buffers.
Read operation: If DQM, DQMU/DQML is High, the output buffer becomes High-Z. If the DQM,
DQMU/DQML is Low, the output buffer becomes Low-Z. (The latency of DQM, DQMU/DQML during
reading is 2 clocks.)
Write operation: If DQM, DQMU/DQML is High, the previous data is held (the new data is not written). If
DQM, DQMU/DQML is Low, the data is written. (The latency of DQM, DQMU/DQML during writing is 0
clock.)
DQ0 to DQ15 (DQ pins): Data is input to and output from these pins (DQ0 to DQ15; HM5225165B, DQ0
to DQ7; HM5225805B, DQ0 to DQ3; HM5225405B).
VCC and VCCQ (power supply pins): 3.3 V is applied. (VCC is for the internal circuit and VCCQ is for the
output buffer.)
Data Sheet E0082H10
9
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
VSS and VSSQ (power supply pins): Ground is connected. (VSS is for the internal circuit and VSSQ is for the
output buffer.)
Command Operation
Command Truth Table
The SDRAM recognizes the following commands specified by the CS, RAS, CAS, WE and address pins.
CKE
A0
CS RAS CAS WE BA0/BA1 A10 to A12
Command
Symbol
DESL
NOP
n - 1 n
Ignore command
No operation
H
H
H
H
H
H
H
H
H
×
×
×
×
×
×
×
×
×
V
×
H
L
L
L
L
L
L
L
L
L
L
×
×
H
L
×
×
×
×
×
H
H
H
H
H
L
H
H
H
L
×
×
Column address and read command READ
V
V
V
V
V
V
×
L
V
V
V
V
V
×
Read with auto-precharge
READ A
L
H
L
Column address and write command WRIT
L
Write with auto-precharge
WRIT A
L
L
H
V
L
Row address strobe and bank active ACTV
H
H
H
L
H
L
Precharge select bank
Precharge all bank
Refresh
PRE
L
PALL
L
L
H
×
×
REF/SELF H
MRS
L
H
L
×
×
Mode register set
H
L
L
V
V
V
Note: H: VIH. L: VIL. ×: VIH or VIL. V: Valid address input
Ignore command [DESL]: When this command is set (CS is High), the SDRAM ignore command input at
the clock. However, the internal status is held.
No operation [NOP]: This command is not an execution command. However, the internal operations
continue.
Column address strobe and read command [READ]: This command starts a read operation. In addition,
the start address of burst read is determined by the column address (AY0 to AY8; HM5225165B, AY0 to
AY9; HM5225805B, AY0 to AY9, AY11; HM5225405B) and the bank select address (BS). After the read
operation, the output buffer becomes High-Z.
Read with auto-precharge [READ A]: This command automatically performs a precharge operation after a
burst read with a burst length of 1, 2, 4 or 8.
Data Sheet E0082H10
10
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Column address strobe and write command [WRIT]: This command starts a write operation. When the
burst write mode is selected, the column address (AY0 to AY8; HM5225165B, AY0 to AY9; HM5225805B,
AY0 to AY9, AY11; HM5225405B) and the bank select address (BA0/BA1) become the burst write start
address. When the single write mode is selected, data is only written to the location specified by the column
address (AY0 to AY8; HM5225165B, AY0 to AY9; HM5225805B, AY0 to AY9, AY11; HM5225405B) and
the bank select address (BA0/BA1).
Write with auto-precharge [WRIT A]: This command automatically performs a precharge operation after a
burst write with a length of 1, 2, 4 or 8, or after a single write operation.
Row address strobe and bank activate [ACTV]: This command activates the bank that is selected by
BA0/BA1 (BS) and determines the row address (AX0 to AX12). When BA0 and BA1 are Low, bank 0 is
activated. When BA0 is Low and BA1 is High, bank 1 is activated. When BA0 is High and BA1 is Low,
bank 2 is activated. When BA0 and BA1 are High, bank 3 is activated.
Precharge selected bank [PRE]: This command starts precharge operation for the bank selected by
BA0/BA1. If BA0 and BA1 are Low, bank 0 is selected. If BA0 is Low and BA1 is High, bank 1 is selected.
If BA0 is High and BA1 is Low, bank 2 is selected. If BA0 and BA1 are High, bank 3 is selected.
Precharge all banks [PALL]: This command starts a precharge operation for all banks.
Refresh [REF/SELF]: This command starts the refresh operation. There are two types of refresh operation,
the one is auto-refresh, and the other is self-refresh. For details, refer to the CKE truth table section.
Mode register set [MRS]: The SDRAM has a mode register that defines how it operates. The mode register
is specified by the address pins (A0 to BA0 and BA1) at the mode register set cycle. For details, refer to the
mode register configuration. After power on, the contents of the mode register are undefined, execute the
mode register set command to set up the mode register.
Data Sheet E0082H10
11
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
DQM Truth Table (HM5225165B)
CKE
Command
Symbol
n - 1
H
n
×
×
×
×
DQMU DQML
Upper byte (DQ8 to DQ15) write enable/output enable ENBU
Lower byte (DQ0 to DQ7) write enable/output enable ENBL
Upper byte (DQ8 to DQ15) write inhibit/output disable MASKU
Lower byte (DQ0 to DQ7) write inhibit/output disable MASKL
L
×
H
×
×
L
×
H
H
H
H
Note: H: VIH. L: VIL. ×: VIH or VIL.
Write: IDID is needed.
Read: IDOD is needed.
DQM Truth Table (HM5225805B/HM5225405B)
CKE
n - 1
H
Command
Symbol
ENB
n
×
×
DQM
Write enable/output enable
Write inhibit/output disable
L
MASK
H
H
Note: H: VIH. L: VIL. ×: VIH or VIL.
Write: IDID is needed.
Read: IDOD is needed.
The SDRAM can mask input/output data by means of DQM, DQMU/DQML.
DQMU masks the upper byte and DQML masks the lower byte. (HM5225165B)
During reading, the output buffer is set to Low-Z by setting DQM, DQMU/DQML to Low, enabling data
output. On the other hand, when DQM, DQMU/DQML is set to High, the output buffer becomes High-Z,
disabling data output.
During writing, data is written by setting DQM, DQMU/DQML to Low. When DQM, DQMU/DQML is set
to High, the previous data is held (the new data is not written). Desired data can be masked during burst read
or burst write by setting DQMU/DQML. For details, refer to the DQM, DQMU/DQML control section of the
SDRAM operating instructions.
Data Sheet E0082H10
12
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
CKE Truth Table
CKE
Current state
Command
n - 1
H
L
n
L
CS
×
RAS CAS WE Address
Active
Clock suspend mode entry
Clock suspend
×
×
×
L
L
H
×
H
×
H
×
×
×
×
L
L
H
×
H
×
H
×
×
×
×
×
×
×
×
×
×
×
×
×
Any
L
×
×
Clock suspend
Clock suspend mode exit
Auto-refresh command (REF)
Self-refresh entry (SELF)
Power down entry
L
H
H
L
×
×
Idle
Idle
Idle
H
H
H
H
L
L
H
H
H
×
L
L
L
L
H
L
Self refresh
Power down
Self refresh exit (SELFX)
Power down exit
H
H
H
H
H
×
L
H
L
L
H
×
L
H
Note: H: VIH. L: VIL. ×: VIH or VIL.
Clock suspend mode entry: The SDRAM enters clock suspend mode from active mode by setting CKE to
Low. If command is input in the clock suspend mode entry cycle, the command is valid. The clock suspend
mode changes depending on the current status (1 clock before) as shown below.
ACTIVE clock suspend: This suspend mode ignores inputs after the next clock by internally maintaining
the bank active status.
READ suspend and READ with Auto-precharge suspend: The data being output is held (and continues to
be output).
WRITE suspend and WRIT with Auto-precharge suspend: In this mode, external signals are not
accepted. However, the internal state is held.
Clock suspend: During clock suspend mode, keep the CKE to Low.
Clock suspend mode exit: The SDRAM exits from clock suspend mode by setting CKE to High during the
clock suspend state.
IDLE: In this state, all banks are not selected, and completed precharge operation.
Auto-refresh command [REF]: When this command is input from the IDLE state, the SDRAM starts auto-
refresh operation. (The auto-refresh is the same as the CBR refresh of conventional DRAMs.) During the
auto-refresh operation, refresh address and bank select address are generated inside the SDRAM. For every
auto-refresh cycle, the internal address counter is updated. Accordingly, 8192 times are required to refresh
the entire memory. Before executing the auto-refresh command, all the banks must be in the IDLE state. In
addition, since the precharge for all banks is automatically performed after auto-refresh, no precharge
command is required after auto-refresh.
Data Sheet E0082H10
13
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Self-refresh entry [SELF]: When this command is input during the IDLE state, the SDRAM starts self-
refresh operation. After the execution of this command, self-refresh continues while CKE is Low. Since self-
refresh is performed internally and automatically, external refresh operations are unnecessary.
Power down mode entry: When this command is executed during the IDLE state, the SDRAM enters power
down mode. In power down mode, power consumption is suppressed by cutting off the initial input circuit.
Self-refresh exit: When this command is executed during self-refresh mode, the SDRAM can exit from self-
refresh mode. After exiting from self-refresh mode, the SDRAM enters the IDLE state.
Power down exit: When this command is executed at the power down mode, the SDRAM can exit from
power down mode. After exiting from power down mode, the SDRAM enters the IDLE state.
Function Truth Table
The following table shows the operations that are performed when each command is issued in each mode of
the SDRAM.
The following table assumes that CKE is high.
Current state
CS
H
L
RAS CAS WE
Address
Command
DESL
Operation
Precharge
×
H
H
H
L
×
H
L
×
×
Enter IDLE after tRP
Enter IDLE after tRP
H
H
L
×
NOP
L
BA, CA, A10 READ/READ A ILLEGAL*4
L
L
BA, CA, A10 WRIT/WRIT A
ILLEGAL*4
ILLEGAL*4
NOP*6
L
H
H
L
H
L
BA, RA
ACTV
L
L
BA, A10
PRE, PALL
REF, SELF
MRS
L
L
H
L
×
ILLEGAL
ILLEGAL
NOP
L
L
L
MODE
Idle
H
L
×
H
H
H
L
×
H
L
×
×
DESL
H
H
L
×
NOP
NOP
L
BA, CA, A10 READ/READ A ILLEGAL*5
L
L
BA, CA, A10 WRIT/WRIT A
ILLEGAL*5
L
H
H
L
H
L
BA, RA
BA, A10
×
ACTV
Bank and row active
NOP
L
L
PRE, PALL
REF, SELF
MRS
L
L
H
L
Refresh
L
L
L
MODE
Mode register set
Data Sheet E0082H10
14
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Current state
CS
H
L
RAS CAS WE
Address
Command
DESL
Operation
NOP
Row active
×
×
×
×
×
H
H
H
L
H
L
H
H
L
NOP
NOP
L
BA, CA, A10 READ/READ A Begin read
L
L
BA, CA, A10 WRIT/WRIT A
Begin write
L
H
H
BA, RA
ACTV
Other bank active
ILLEGAL on same bank*3
L
L
L
H
L
L
L
H
L
L
BA, A10
PRE, PALL
REF, SELF
MRS
Precharge
L
H
L
×
ILLEGAL
L
L
MODE
ILLEGAL
Read
×
H
H
×
H
L
×
×
×
DESL
Continue burst to end
Continue burst to end
H
H
NOP
BA, CA, A10 READ/READ A Continue burst read to CAS
latency and New read
L
L
H
L
L
L
BA, CA, A10 WRIT/WRIT A
Term burst read/start write
H
H
BA, RA
ACTV
Other bank active
ILLEGAL on same bank*3
L
L
H
L
BA, A10
PRE, PALL
Term burst read and
Precharge
L
L
H
L
L
×
L
L
×
H
L
×
REF, SELF
MRS
ILLEGAL
ILLEGAL
MODE
Read with auto-
precharge
×
×
DESL
Continue burst to end and
precharge
L
H
H
H
×
NOP
Continue burst to end and
precharge
L
L
L
H
H
L
L
L
H
H
L
BA, CA, A10 READ/READ A ILLEGAL*4
BA, CA, A10 WRIT/WRIT A
ILLEGAL*4
H
BA, RA
ACTV
Other bank active
ILLEGAL on same bank*3
L
L
L
L
L
L
H
L
L
L
H
L
BA, A10
×
PRE, PALL
REF, SELF
MRS
ILLEGAL*4
ILLEGAL
ILLEGAL
MODE
Data Sheet E0082H10
15
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Current state
CS
H
L
RAS CAS WE
Address
Command
DESL
Operation
Write
×
×
×
×
×
Continue burst to end
Continue burst to end
H
H
H
L
H
L
H
H
L
NOP
L
BA, CA, A10 READ/READ A Term burst and New read
L
L
BA, CA, A10 WRIT/WRIT A
Term burst and New write
L
H
H
BA, RA
ACTV
Other bank active
ILLEGAL on same bank*3
L
L
H
L
BA, A10
PRE, PALL
Term burst write and
Precharge*2
L
L
H
L
L
×
L
L
×
H
L
×
REF, SELF
MRS
ILLEGAL
ILLEGAL
MODE
Write with auto-
precharge
×
×
DESL
Continue burst to end and
precharge
L
H
H
H
×
NOP
Continue burst to end and
precharge
L
L
L
H
H
L
L
L
H
H
L
BA, CA, A10 READ/READ A ILLEGAL*4
BA, CA, A10 WRIT/WRIT A
ILLEGAL*4
H
BA, RA
ACTV
Other bank active
ILLEGAL on same bank*3
L
L
L
H
L
L
L
×
H
L
L
×
L
H
L
×
BA, A10
PRE, PALL
REF, SELF
MRS
ILLEGAL*4
×
ILLEGAL
MODE
ILLEGAL
Refresh (auto-
refresh)
×
DESL
Enter IDLE after tRC
L
L
L
L
L
L
L
H
H
H
L
H
L
H
H
L
×
NOP
Enter IDLE after tRC
BA, CA, A10 READ/READ A ILLEGAL*5
L
BA, CA, A10 WRIT/WRIT A
ILLEGAL*5
ILLEGAL*5
ILLEGAL*5
ILLEGAL
H
H
L
H
L
BA, RA
BA, A10
×
ACTV
L
PRE, PALL
REF, SELF
MRS
L
H
L
L
L
MODE
ILLEGAL
Notes: 1. H: VIH. L: VIL. ×: VIH or VIL. The other combinations are inhibit.
2. An interval of tDPL is required between the final valid data input and the precharge command.
3. If tRRD is not satisfied, this operation is illegal.
4. Illegal for same bank, except for another bank.
5. Illegal for all banks.
6. NOP for same bank, except for another bank.
Data Sheet E0082H10
16
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
From PRECHARGE state, command operation
To [DESL], [NOP]: When these commands are executed, the SDRAM enters the IDLE state after tRP has
elapsed from the completion of precharge.
From IDLE state, command operation
To [DESL], [NOP], [PRE] or [PALL]: These commands result in no operation.
To [ACTV]: The bank specified by the address pins and the ROW address is activated.
To [REF], [SELF]: The SDRAM enters refresh mode (auto-refresh or self-refresh).
To [MRS]: The synchronous DRAM enters the mode register set cycle.
From ROW ACTIVE state, command operation
To [DESL], [NOP]: These commands result in no operation.
To [READ], [READ A]: A read operation starts. (However, an interval of tRCD is required.)
To [WRIT], [WRIT A]: A write operation starts. (However, an interval of tRCD is required.)
To [ACTV]: This command makes the other bank active. (However, an interval of tRRD is required.)
Attempting to make the currently active bank active results in an illegal command.
To [PRE], [PALL]: These commands set the SDRAM to precharge mode. (However, an interval of tRAS is
required.)
From READ state, command operation
To [DESL], [NOP]: These commands continue read operations until the burst operation is completed.
To [READ], [READ A]: Data output by the previous read command continues to be output. After CAS
latency, the data output resulting from the next command will start.
To [WRIT], [WRIT A]: These commands stop a burst read, and start a write cycle.
To [ACTV]: This command makes other banks bank active. (However, an interval of tRRD is required.)
Attempting to make the currently active bank active results in an illegal command.
To [PRE], [PALL]: These commands stop a burst read, and the SDRAM enters precharge mode.
From READ with AUTO-PRECHARGE state, command operation
Data Sheet E0082H10
17
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
To [DESL], [NOP]: These commands continue read operations until the burst operation is completed, and
the SDRAM then enters precharge mode.
To [ACTV]: This command makes other banks bank active. (However, an interval of tRRD is required.)
Attempting to make the currently active bank active results in an illegal command.
From WRITE state, command operation
To [DESL], [NOP]: These commands continue write operations until the burst operation is completed.
To [READ], [READ A]: These commands stop a burst and start a read cycle.
To [WRIT], [WRIT A]: These commands stop a burst and start the next write cycle.
To [ACTV]: This command makes the other bank active. (However, an interval of tRRD is required.)
Attempting to make the currently active bank active results in an illegal command.
To [PRE], [PALL]: These commands stop burst write and the SDRAM then enters precharge mode.
From WRITE with AUTO-PRECHARGE state, command operation
To [DESL], [NOP]: These commands continue write operations until the burst is completed, and the
synchronous DRAM enters precharge mode.
To [ACTV]: This command makes the other bank active. (However, an interval of tRRD is required.)
Attempting to make the currently active bank active results in an illegal command.
From REFRESH state, command operation
To [DESL], [NOP]: After an auto-refresh cycle (after tRC), the SDRAM automatically enters the IDLE state.
Data Sheet E0082H10
18
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Simplified State Diagram
SELF
REFRESH
SR ENTRY
SR EXIT
*1
MRS
REFRESH
MODE
REGISTER
SET
AUTO
REFRESH
IDLE
CKE
CKE_
IDLE
POWER
DOWN
ACTIVE
ACTIVE
CLOCK
SUSPEND
CKE_
CKE
ROW
ACTIVE
WRITE
READ
Write
WRITE
WITH
AP
READ
WITH
AP
Read
CKE_
CKE_
CKE
WRITE
SUSPEND
READ
READ
SUSPEND
WRITE
READ
WRITE
CKE
READ
WITH AP
WRITE
WITH AP
WRITE
WITH AP
READ
WITH AP
PRECHARGE
CKE_
CKE_
WRITEA
SUSPEND
READA
SUSPEND
WRITEA
READA
CKE
CKE
PRECHARGE PRECHARGE
POWER
APPLIED
POWER
ON
PRECHARGE
PRECHARGE
Automatic transition after completion of command.
Transition resulting from command input.
Note: 1. After the auto-refresh operation, precharge operation is performed automatically and
enter the IDLE state.
Data Sheet E0082H10
19
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Mode Register Configuration
The mode register is set by the input to the address pins (A0 to A12, BA0 and BA1) during mode register set
cycles. The mode register consists of five sections, each of which is assigned to address pins.
BA1, BA0, A11, A10, A12, A9, A8: (OPCODE): The SDRAM has two types of write modes. One is the
burst write mode, and the other is the single write mode. These bits specify write mode.
Burst read and burst write: Burst write is performed for the specified burst length starting from the column
address specified in the write cycle.
Burst read and single write: Data is only written to the column address specified during the write cycle,
regardless of the burst length.
A7: Keep this bit Low at the mode register set cycle. If this pin is high, the vender test mode is set.
A6, A5, A4: (LMODE): These pins specify the CAS latency.
A3: (BT): A burst type is specified.
A2, A1, A0: (BL): These pins specify the burst length.
A12
A11
OPCODE
BA1 BA0
A10
A9
A8
A7
0
A6
A5
A4
A3
BT
A2
A1
BL
A0
LMODE
A6 A5 A4 CAS latency
A3 Burst type
Burst length
BT=0 BT=1
A2 A1 A0
R
R
2
0
0
0
0
1
0
0
1
1
X
0
1
0
1
X
0
1
Sequential
Interleave
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
2
2
3
4
4
R
8
8
R
R
R
R
R
R
R
R
A9 A8
Write mode
A10
BA1
0
BA0 A12
A11
0
0
1
1
0
1
0
1
Burst read and burst write
0
X
X
X
0
X
X
X
0
X
X
X
0
X
X
X
R
X
Burst read and single write
R
R is Reserved (inhibit)
X: 0 or 1
X
X
Data Sheet E0082H10
20
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Burst Sequence
Burst length = 2
Starting Ad. Addressing(decimal)
Burst length = 4
Starting Ad. Addressing(decimal)
A0
0
Sequential Interleave
A1
0
A0 Sequential
Interleave
0, 1,
1, 0,
0, 1,
1, 0,
0
1
0
1
0, 1, 2, 3,
1, 2, 3, 0,
2, 3, 0, 1,
0, 1, 2, 3,
1, 0, 3, 2,
2, 3, 0, 1,
3, 2, 1, 0,
1
0
1
1
3,
0, 1, 2,
Burst length = 8
Starting Ad.
Addressing(decimal)
A2 A1 A0 Sequential
Interleave
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0, 1, 2, 3, 4, 5, 6, 7,
1, 2, 3, 4, 5, 6, 7, 0,
2, 3, 4, 5, 6, 7, 0, 1,
3, 4, 5, 6, 7, 0, 1, 2,
4, 5, 6, 7, 0, 1, 2, 3,
5, 6, 7, 0, 1, 2, 3, 4,
6, 7, 0, 1, 2, 3, 4, 5,
7, 0, 1, 2, 3, 4, 5, 6,
0, 1, 2, 3, 4, 5, 6, 7,
1, 0, 3, 2, 5, 4, 7, 6,
2, 3, 0, 1, 6, 7, 4, 5,
3, 2, 1, 0, 7, 6, 5, 4,
4, 5, 6, 7, 0, 1, 2, 3,
5, 4, 7, 6, 1, 0, 3, 2,
6, 7, 4, 5, 2, 3, 0, 1,
7, 6, 5, 4, 3, 2, 1, 0,
Data Sheet E0082H10
21
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Operation of the SDRAM
The following chapter shows operation example of the products below.
Organization
Input/output mask
DQMU/DQML
DQM
CAS latency
4-Mword × 16-bit × 4 bank
8-Mword × 8-bit × 4 bank
16-Mword × 4-bit × 4 bank
2/3
DQM
Note: The SDRAM should be used according to the product capability (See “Features”, “Pin Description”
and “AC Characteristics”).
Read/Write Operations
Bank active: Before executing a read or write operation, the corresponding bank and the row address must be
activated by the bank active (ACTV) command. An interval of tRCD is required between the bank active
command input and the following read/write command input.
Read operation: A read operation starts when a read command is input. Output buffer becomes Low-Z in
the (CAS Latency - 1) cycle after read command set. The SDRAM can perform a burst read operation.
The burst length can be set to 1, 2, 4, 8. The start address for a burst read is specified by the column address
and the bank select address (BA0/BA1) at the read command set cycle. In a read operation, data output starts
after the number of clocks specified by the CAS Latency. The CAS Latency can be set to 2 or 3.
When the burst length is 1, 2, 4, 8, the Dout buffer automatically becomes High-Z at the next clock after the
successive burst-length data has been output.
The CAS latency and burst length must be specified at the mode register.
Data Sheet E0082H10
22
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
CAS Latency
CLK
Command
Address
t
RCD
READ
ACTV
Row
Column
out 3
out 1 out 2
out 0
out 1 out 2
CL = 2
CL = 3
Dout
out 3
out 0
CL = CAS latency
Burst Length = 4
Burst Length
CLK
t
RCD
Command
Address
ACTV
Row
READ
Column
out 0
BL = 1
out 0 out 1
BL = 2
BL = 4
BL = 8
Dout
out 3
out 3
out 0 out 1 out 2
out 0 out 1 out 2
out 5 out 6 out 7
out 4
BL : Burst Length
CAS Latency = 2
Data Sheet E0082H10
23
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Write operation: Burst write or single write mode is selected by the OPCODE (BA1, BA0, A12, A11, A10,
A9, A8) of the mode register.
1. Burst write: A burst write operation is enabled by setting OPCODE (A9, A8) to (0, 0). A burst write
starts in the same clock as a write command set. (The latency of data input is 0 clock.) The burst length can
be set to 1, 2, 4 and 8, like burst read operations. The write start address is specified by the column address
and the bank select address (BA0/BA1) at the write command set cycle.
CLK
t
RCD
Command
Address
ACTV
Row
WRIT
Column
in 0
in 0
BL = 1
in 1
in 1
in 1
BL = 2
BL = 4
BL = 8
Din
in 3
in 2
in 2
in 0
in 0
in 5
in 6 in 7
in 3 in 4
CAS Latency = 2, 3
2. Single write: A single write operation is enabled by setting OPCODE (A9, A8) to (1, 0). In a single write
operation, data is only written to the column address and the bank select address (BA0/BA1) specified by the
write command set cycle without regard to the burst length setting. (The latency of data input is 0 clock).
CLK
t
RCD
Command
WRIT
ACTV
Row
Column
in 0
Address
Din
Data Sheet E0082H10
24
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Auto Precharge
Read with auto-precharge: In this operation, since precharge is automatically performed after completing a
read operation, a precharge command need not be executed after each read operation. The command executed
for the same bank after the execution of this command must be the bank active (ACTV) command. In
addition, an interval defined by lAPR is required before execution of the next command.
CAS latency
Precharge start cycle
3
2
2 cycle before the final data is output
1 cycle before the final data is output
Burst Read (Burst Length = 4)
CLK
ACTV
READ A
ACTV
CL=2 Command
DQ (input)
l
RAS
out0
out1
out2
out3
l
APR
CL=3 Command
DQ (input)
ACTV
READ A
ACTV
l
RAS
out0
out1
out2
out3
l
APR
Note: Internal auto-precharge starts at the timing indicated by " ".
And an interval of t
(l
) is required between previous active (ACTV) command and internal precharge
"
".
RAS RAS
Data Sheet E0082H10
25
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Write with auto-precharge: In this operation, since precharge is automatically performed after completing
a burst write or single write operation, a precharge command need not be executed after each write operation.
The command executed for the same bank after the execution of this command must be the bank active
(ACTV) command. In addition, an interval of lAPW is required between the final valid data input and input of
next command.
Burst Write (Burst Length = 4)
CLK
WRIT A
ACTV
ACTV
Command
DQ (input)
IRAS
in0 in1 in2 in3
lAPW
Note: Internal auto-precharge starts at the timing indicated by " ".
and an interval of tRAS (lRAS) is required between previous active (ACTV) command
and internal precharge " ".
Single Write
CLK
WRIT A
ACTV
ACTV
Command
IRAS
DQ (input)
in
lAPW
Note: Internal auto-precharge starts at the timing indicated by " ".
and an interval of tRAS (lRAS) is required between previous active (ACTV) command
and internal precharge " ".
Data Sheet E0082H10
26
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Command Intervals
Read command to Read command interval:
1. Same bank, same ROW address: When another read command is executed at the same ROW address
of the same bank as the preceding read command execution, the second read can be performed after an
interval of no less than 1 clock. Even when the first command is a burst read that is not yet finished, the data
read by the second command will be valid.
READ to READ Command Interval (same ROW address in same bank)
CLK
Command
READ
ACTV
Row
READ
Column B
Column A
Address
BS
Dout
out A0
out B2 out B3
out B0 out B1
CAS Latency = 3
Burst Length = 4
Bank 0
Column =B
Dout
Bank0
Active
Column =A Column =B Column =A
Read Read Dout
2. Same bank, different ROW address: When the ROW address changes on same bank, consecutive read
commands cannot be executed; it is necessary to separate the two read commands with a precharge command
and a bank-active command.
3. Different bank: When the bank changes, the second read can be performed after an interval of no less
than 1 clock, provided that the other bank is in the bank-active state. Even when the first command is a burst
read that is not yet finished, the data read by the second command will be valid.
READ to READ Command Interval (different bank)
CLK
Command
READ READ
ACTV
Row 0
ACTV
Column A
Row 1
Column B
Address
BS
Dout
out A0
out B2 out B3
out B0 out B1
Bank3
Dout
Bank0
Dout
CAS Latency = 3
Burst Length = 4
Bank0
Active
Bank3 Bank0 Bank3
Active Read Read
Data Sheet E0082H10
27
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Write command to Write command interval:
1. Same bank, same ROW address: When another write command is executed at the same ROW address
of the same bank as the preceding write command, the second write can be performed after an interval of no
less than 1 clock. In the case of burst writes, the second write command has priority.
WRITE to WRITE Command Interval (same ROW address in same bank)
CLK
Command
Address
WRIT
ACTV
Row
WRIT
Column B
Column A
BS
Din
in A0
in B2 in B3
in B0 in B1
Bank0
Active
Column =A Column =B
Write Write
Burst Write Mode
Burst Length = 4
Bank 0
2. Same bank, different ROW address: When the ROW address changes, consecutive write commands
cannot be executed; it is necessary to separate the two write commands with a precharge command and a
bank-active command.
3. Different bank: When the bank changes, the second write can be performed after an interval of no less
than 1 clock, provided that the other bank is in the bank-active state. In the case of burst write, the second
write command has priority.
WRITE to WRITE Command Interval (different bank)
CLK
Command
Address
ACTV
Row 0
ACTV
WRIT WRIT
Column A
Column B
Row 1
BS
Din
in A0
in B2 in B3
in B0 in B1
Burst Write Mode
Burst Length = 4
Bank0
Active
Bank3 Bank0 Bank3
Active Write Write
Data Sheet E0082H10
28
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Read command to Write command interval:
1. Same bank, same ROW address: When the write command is executed at the same ROW address of the
same bank as the preceding read command, the write command can be performed after an interval of no less
than 1 clock. However, DQM, DQMU/DQML must be set High so that the output buffer becomes High-Z
before data input.
READ to WRITE Command Interval (1)
CLK
Command
READ WRIT
DQM, CL=2
DQMU
/DQML
CL=3
in B0
in B3
in B1 in B2
Din
Burst Length = 4
Burst write
High-Z
Dout
READ to WRITE Command Interval (2)
CLK
Command
READ
WRIT
DQM,
DQMU/DQML
2 clock
High-Z
High-Z
CL=2
Dout
CL=3
Din
2. Same bank, different ROW address: When the ROW address changes, consecutive write commands
cannot be executed; it is necessary to separate the two commands with a precharge command and a bank-
active command.
3. Different bank: When the bank changes, the write command can be performed after an interval of no less
than 1 cycle, provided that the other bank is in the bank-active state. However, DQM, DQMU/DQML must
be set High so that the output buffer becomes High-Z before data input.
Data Sheet E0082H10
29
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Write command to Read command interval:
1. Same bank, same ROW address: When the read command is executed at the same ROW address of the
same bank as the preceding write command, the read command can be performed after an interval of no less
than 1 clock. However, in the case of a burst write, data will continue to be written until one clock before the
read command is executed.
WRITE to READ Command Interval (1)
CLK
Command
WRIT
in A0
READ
DQM,
DQMU/DQML
Din
Dout
out B0
out B1
out B2
out B3
Column = A
Write
Burst Write Mode
CAS Latency = 2
Burst Length = 4
Bank 0
CAS Latency
Column = B
Dout
Column = B
Read
WRITE to READ Command Interval (2)
CLK
WRIT
in A0
READ
Command
DQM,
DQMU/DQML
Din
in A1
Dout
out B0
out B1
out B2
out B3
Burst Write Mode
CAS Latency = 2
Burst Length = 4
Bank 0
Column = A
Write
CAS Latency
Column = B
Dout
Column = B
Read
2. Same bank, different ROW address: When the ROW address changes, consecutive read commands
cannot be executed; it is necessary to separate the two commands with a precharge command and a bank-
active command.
3. Different bank: When the bank changes, the read command can be performed after an interval of no less
than 1 clock, provided that the other bank is in the bank-active state. However, in the case of a burst write,
data will continue to be written until one clock before the read command is executed (as in the case of the
same bank and the same address).
Data Sheet E0082H10
30
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Read with auto precharge to Read command interval
1. Different bank: When some banks are in the active state, the second read command (another bank) is
executed. Even when the first read with auto-precharge is a burst read that is not yet finished, the data read by
the second command is valid. The internal auto-precharge of one bank starts at the next clock of the second
command.
Read with Auto Precharge to Read Command Interval (Different bank)
CLK
Command
BS
READ A
READ
Dout
out A0
out A1
out B0
out B1
bank0
Read A
bank3
Read
CAS Latency = 3
Burst Length = 4
Note: Internal auto-precharge starts at the timing indicated by "
".
2. Same bank: The consecutive read command (the same bank) is illegal.
Write with auto precharge to Write command interval
1. Different bank: When some banks are in the active state, the second write command (another bank) is
executed. In the case of burst writes, the second write command has priority. The internal auto-precharge of
one bank starts at the next clock of the second command .
Write with Auto Precharge to Write Command Interval (Different bank)
CLK
Command
BS
WRIT A
in A0
WRIT
in B0
Din
in A1
in B1
in B2
in B3
bank0
Write A
bank3
Write
Burst Length = 4
Note: Internal auto-precharge starts at the timing indicated by "
".
2. Same bank: The consecutive write command (the same bank) is illegal.
Data Sheet E0082H10
31
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Read with auto precharge to Write command interval
1. Different bank: When some banks are in the active state, the second write command (another bank) is
executed. However, DQM, DQMU/DQML must be set High so that the output buffer becomes High-Z before
data input. The internal auto-precharge of one bank starts at the next clock of the second command.
Read with Auto Precharge to Write Command Interval (Different bank)
CLK
Command
BS
READ A WRIT
CL = 2
CL = 3
Din
DQM,
DQMU/DQML
in B0
in B1
in B2
in B3
Dout
High-Z
Burst Length = 4
bank0
bank3
Read A Write
Note: Internal auto-precharge starts at the timing indicated by "
".
2. Same bank: The consecutive write command from read with auto precharge (the same bank) is illegal. It
is necessary to separate the two commands with a bank active command.
Data Sheet E0082H10
32
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Write with auto precharge to Read command interval
1. Different bank: When some banks are in the active state, the second read command (another bank) is
executed. However, in case of a burst write, data will continue to be written until one clock before the read
command is executed. The internal auto-precharge of one bank starts at the next clock of the second
command.
Write with Auto Precharge to Read Command Interval (Different bank)
CLK
Command
BS
WRIT A
in A0
READ
DQM,
DQMU/DQML
Din
Dout
out B0
out B1
out B2 out B3
CAS Latency = 3
Burst Length = 4
bank0
Write A
bank3
Read
Note: Internal auto-precharge starts at the timing indicated by "
".
2. Same bank: The consecutive read command from write with auto precharge (the same bank) is illegal. It
is necessary to separate the two commands with a bank active command.
Data Sheet E0082H10
33
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Read command to Precharge command interval (same bank):
When the precharge command is executed for the same bank as the read command that preceded it, the
minimum interval between the two commands is one clock. However, since the output buffer then becomes
High-Z after the clocks defined by lHZP, there is a case of interruption to burst read data output will be
interrupted, if the precharge command is input during burst read. To read all data by burst read, the clocks
defined by lEP must be assured as an interval from the final data output to precharge command execution.
READ to PRECHARGE Command Interval (same bank): To output all data
CAS Latency = 2, Burst Length = 4
CLK
PRE/PALL
out A2
READ
Command
Dout
out A0
out A1
out A3
CL=2
l
= -1 cycle
EP
CAS Latency = 3, Burst Length = 4
CLK
PRE/PALL
out A1
READ
Command
Dout
out A0
out A2
out A3
CL=3
l
= -2 cycle
EP
Data Sheet E0082H10
34
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
READ to PRECHARGE Command Interval (same bank): To stop output data
CAS Latency = 2, Burst Length = 1, 2, 4, 8
CLK
PRE/PALL
READ
Command
Dout
High-Z
out A0
=2
l
HZP
CAS Latency = 3, Burst Length = 1, 2, 4, 8
CLK
PRE/PALL
READ
Command
Dout
High-Z
out A0
l
=3
HZP
Data Sheet E0082H10
35
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Write command to Precharge command interval (same bank): When the precharge command is executed
for the same bank as the write command that preceded it, the minimum interval between the two commands is
1 clock. However, if the burst write operation is unfinished, the input data must be masked by means of
DQM, DQMU/DQML for assurance of the clock defined by tDPL
.
WRITE to PRECHARGE Command Interval (same bank)
Burst Length = 4 (To stop write operation)
CLK
PRE/PALL
Command
WRIT
DQM,
DQMU/DQML
Din
t
DPL
CLK
PRE/PALL
WRIT
Command
DQM,
DQMU/DQML
Din
in A0
in A1
t
DPL
Burst Length = 4 (To write all data)
CLK
PRE/PALL
Command
WRIT
in A0
DQM,
DQMU/DQML
Din
in A1
in A2
in A3
t
DPL
Data Sheet E0082H10
36
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Bank active command interval:
1. Same bank: The interval between the two bank-active commands must be no less than tRC.
2. In the case of different bank-active commands: The interval between the two bank-active commands
must be no less than tRRD
.
Bank Active to Bank Active for Same Bank
CLK
Command
Address
BS
ACTV
ROW
ACTV
ROW
t
RC
Bank 0
Active
Bank 0
Active
Bank Active to Bank Active for Different Bank
CLK
ACTV
ACTV
Command
Address
ROW:0
ROW:1
BS
t
RRD
Bank 0
Active
Bank 3
Active
Data Sheet E0082H10
37
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Mode register set to Bank-active command interval: The interval between setting the mode register and
executing a bank-active command must be no less than lRSA
.
CLK
Command
Address
MRS
ACTV
CODE
BS & ROW
I
RSA
Mode
Bank
Register Set Active
Data Sheet E0082H10
38
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
DQM Control
The DQM mask the DQ data. The DQMU and DQML mask the upper and lower bytes of the DQ data,
respectively. The timing of DQMU/DQML is different during reading and writing.
Reading: When data is read, the output buffer can be controlled by DQM, DQMU/DQML. By setting
DQM, DQMU/DQML to Low, the output buffer becomes Low-Z, enabling data output. By setting DQM,
DQMU/DQML to High, the output buffer becomes High-Z, and the corresponding data is not output.
However, internal reading operations continue. The latency of DQM, DQMU/DQML during reading is 2
clocks.
Writing: Input data can be masked by DQM, DQMU/DQML. By setting DQM, DQMU/DQML to Low,
data can be written. In addition, when DQM, DQMU/DQML is set to High, the corresponding data is not
written, and the previous data is held. The latency of DQM, DQMU/DQML during writing is 0 clock.
Reading
CLK
DQM,
DQMU/DQML
High-Z
DQ (output)
out 0
l
out 1
out 3
= 2 Latency
DOD
Writing
CLK
DQM,
DQMU/DQML
DQ (input)
in 3
in 0
in 1
l
= 0 Latency
DID
Data Sheet E0082H10
39
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Refresh
Auto-refresh: All the banks must be precharged before executing an auto-refresh command. Since the auto-
refresh command updates the internal counter every time it is executed and determines the banks and the
ROW addresses to be refreshed, external address specification is not required. The refresh cycle is 8192
cycles/64 ms. (8192 cycles are required to refresh all the ROW addresses.) The output buffer becomes High-
Z after auto-refresh start. In addition, since a precharge has been completed by an internal operation after the
auto-refresh, an additional precharge operation by the precharge command is not required.
Self-refresh: After executing a self-refresh command, the self-refresh operation continues while CKE is held
Low. During self-refresh operation, all ROW addresses are refreshed by the internal refresh timer. A self-
refresh is terminated by a self-refresh exit command. Before and after self-refresh mode, execute auto-refresh
to all refresh addresses in or within 64 ms period on the condition (1) and (2) below.
(1) Enter self-refresh mode within 7.8 µs after either burst refresh or distributed refresh at equal interval to all
refresh addresses are completed.
(2) Start burst refresh or distributed refresh at equal interval to all refresh addresses within 7.8 µs after exiting
from self-refresh mode.
Others
Power-down mode: The SDRAM enters power-down mode when CKE goes Low in the IDLE state. In
power down mode, power consumption is suppressed by deactivating the input initial circuit. Power down
mode continues while CKE is held Low. In addition, by setting CKE to High, the SDRAM exits from the
power down mode, and command input is enabled from the next clock. In this mode, internal refresh is not
performed.
Clock suspend mode: By driving CKE to Low during a bank-active or read/write operation, the SDRAM
enters clock suspend mode. During clock suspend mode, external input signals are ignored and the internal
state is maintained. When CKE is driven High, the SDRAM terminates clock suspend mode, and command
input is enabled from the next clock. For details, refer to the "CKE Truth Table".
Power-up sequence: The SDRAM should be goes on the following sequence with power up.
The CLK, CKE, CS, DQM, DQMU/DQML and DQ pins keep low till power stabilizes.
The CLK pin is stabilized within 100 µs after power stabilizes before the following initialization sequence.
The CKE and DQM, DQMU/DQML is driven to high between power stabilizes and the initialization
sequence.
This SDRAM has VCC clamp diodes for CLK, CKE, CS DQM, DQMU/DQML and DQ pins. If these pins go
high before power up, the large current flows from these pins to VCC through the diodes.
Initialization sequence: When 200 µs or more has past after the above power-up sequence, all banks must be
precharged using the precharge command (PALL). After tRP delay, set 8 or more auto refresh commands
(REF). Set the mode register set command (MRS) to initialize the mode register. We recommend that by
keeping DQM, DQMU/DQML and CKE to High, the output buffer becomes High-Z during Initialization
sequence, to avoid DQ bus contention on memory system formed with a number of device.
Data Sheet E0082H10
40
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Initialization sequence
Power up sequence
100 µs
200 µs
VCC, VCC
Q
0 V
CKE, DQM,
DQMU/DQML
Low
Low
Low
CLK
CS, DQ
Power stabilize
Absolute Maximum Ratings
Parameter
Symbol
Value
Unit
Note
Voltage on any pin relative to VSS
VT
–0.5 to VCC + 0.5
V
1
(≤ 4.6 (max))
Supply voltage relative to VSS
Short circuit output current
Power dissipation
VCC
–0.5 to +4.6
50
V
1
Iout
PT
mA
W
1.0
Operating temperature
Storage temperature
Topr
Tstg
0 to +70
–55 to +125
°C
°C
Note: 1. Respect to VSS.
DC Operating Conditions (Ta = 0 to +70˚C)
Parameter
Symbol
VCC, VCCQ
VSS, VSSQ
VIH
Min
3.0
0
Max
3.6
Unit
V
Notes
1, 2
3
Supply voltage
0
V
Input high voltage
Input low voltage
2.0
–0.3
VCC + 0.3
0.8
V
1, 4
1, 5
VIL
V
Notes: 1. All voltage referred to VSS.
2. The supply voltage with all VCC and VCCQ pins must be on the same level.
3. The supply voltage with all VSS and VSSQ pins must be on the same level.
4. VIH (max) = VCC + 2.0 V for pulse width ≤ 3 ns at VCC.
5. VIL (min) = VSS – 2.0 V for pulse width ≤ 3 ns at VSS.
Data Sheet E0082H10
41
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
VIL/VIH Clamp
This SDRAM has VIL and VIH clamp for CLK, CKE, CS, DQM and DQ pins.
Minimum VIL Clamp Current
VIL (V)
–2
I (mA)
–32
–25
–19
–13
–8
–1.8
–1.6
–1.4
–1.2
–1
–4
–0.9
–0.8
–0.6
–0.4
–0.2
0
–2
–0.6
0
0
0
0
0
–2
–1.5
–1
–0.5
0
–5
–10
–15
–20
–25
–30
–35
VIL (V)
Data Sheet E0082H10
42
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Minimum VIH Clamp Current
VIH (V)
I (mA)
10
8
VCC + 2
VCC + 1.8
VCC + 1.6
VCC + 1.4
VCC + 1.2
VCC + 1
5.5
3.5
1.5
0.3
0
VCC + 0.8
VCC + 0.6
VCC + 0.4
VCC + 0.2
VCC + 0
0
0
0
0
10
8
6
4
2
0
V
CC + 0
VCC + 0.5
VCC + 1
VIH (V)
VCC + 1.5
VCC + 2
Data Sheet E0082H10
43
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
IOL/IOH Characteristics
Output Low Current (IOL)
IOL
IOL
Vout (V)
0
Min (mA)
0
Max (mA)
0
0.4
27
71
0.65
0.85
1
41
108
134
151
188
194
203
209
212
220
223
51
58
1.4
70
1.5
72
1.65
1.8
75
77
1.95
3
77
80
3.45
81
250
200
150
100
min
max
50
0
0
0.5
1
1.5
2
2.5
3
3.5
Vout (V)
Data Sheet E0082H10
44
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Output High Current (IOH) (Ta = 0 to +70˚C, VCC, VCCQ = 3.0 V to 3.45 V, VSS, VSSQ = 0 V)
IOH
IOH
Vout (V)
3.45
3.3
3
Min (mA)
—
Max (mA)
–3
—
–28
0
–75
2.6
2.4
2
–21
–34
–59
–67
–73
–78
–81
–89
–93
–130
–154
–197
–227
–248
–270
–285
–345
–503
1.8
1.65
1.5
1.4
1
0
0
0
0.5
1
1.5
2
2.5
3
3.5
–100
–200
–300
min
max
–400
–500
–600
Vout (V)
Data Sheet E0082H10
45
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
DC Characteristics (Ta = 0 to +70˚C, VCC, VCCQ = 3.3 V ± 0.3 V, VSS, VSSQ = 0 V)
(HM5225165B)
HM5225165B
-75
-A6
-B6
Parameter
Symbol Min Max Min Max Min Max Unit Test conditions
Notes
Operating current
Burst length = 1
1, 2, 3
(CAS latency = 2)
ICC1
ICC1
—
—
—
115
115
3
—
—
—
100
100
3
—
—
—
80
mA
tRC = min
(CAS latency = 3)
100 mA
Standby current in power ICC2P
down
3
mA
mA
mA
mA
CKE = VIL,
6
7
4
9
t
CK = 12 ns
Standby current in power ICC2PS
down (input signal stable)
—
—
—
2
—
—
—
2
—
—
—
2
CKE = VIL, tCK = ∞
Standby current in non
power down
ICC2N
20
9
20
9
20
9
CKE, CS = VIH,
t
CK = 12 ns
Standby current in non
power down (input signal
stable)
ICC2NS
CKE = VIH, tCK = ∞
Active standby current in
power down
ICC3P
—
—
4
3
—
—
4
3
—
—
4
3
mA
mA
CKE = VIL,
1, 2, 6
t
CK = 12 ns
Active standby current in
power down (input signal
stable)
ICC3PS
CKE = VIL, tCK = ∞ 2, 7
Active standby current in
non power down
ICC3N
—
—
30
15
—
—
30
15
—
—
30
15
mA
mA
CKE, CS = VIH,
CK = 12 ns
1, 2, 4
t
Active standby current in
non power down (input
signal stable)
ICC3NS
CKE = VIH, tCK = ∞ 2, 9
Burst operating current
(CAS latency = 2)
ICC4
ICC4
ICC5
ICC6
—
—
—
—
110
145
220
3
—
—
—
—
110
110
220
3
—
—
—
—
85
mA
tCK = min, BL = 4
tRC = min
1, 2, 5
(CAS latency = 3)
Refresh current
110 mA
220 mA
3
8
Self refresh current
3
2
1
mA
mA
µA
VIH ≥ VCC – 0.2 V
VIL ≤ 0.2 V
Self refresh current
(L-version)
ICC6
—
2
1
—
2
1
—
Input leakage current
Output leakage current
ILI
–1
–1
–1
0 ≤ Vin ≤ VCC
ILO
–1.5 1.5 –1.5 1.5 –1.5 1.5 µA
0 ≤ Vout ≤ VCC
DQ = disable
Output high voltage
Output low voltage
VOH
VOL
2.4
—
2.4
—
2.4
—
V
V
IOH = –4 mA
—
0.4
—
0.4
—
0.4
IOL = 4 mA
Data Sheet E0082H10
46
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
DC Characteristics (Ta = 0 to +70˚C, VCC, VCCQ = 3.3 V ± 0.3 V, VSS, VSSQ = 0 V)
(HM5225805B)
HM5225805B
-75
-A6
-B6
Parameter
Symbol Min Max Min Max Min Max Unit Test conditions
Notes
Operating current
Burst length = 1
1, 2, 3
(CAS latency = 2)
ICC1
ICC1
—
—
—
110
110
3
—
—
—
95
95
3
—
—
—
75
95
3
mA
mA
mA
tRC = min
(CAS latency = 3)
Standby current in power ICC2P
down
CKE = VIL,
6
7
4
9
t
CK = 12 ns
Standby current in power ICC2PS
down (input signal stable)
—
—
—
2
—
—
—
2
—
—
—
2
mA
mA
mA
CKE = VIL, tCK = ∞
Standby current in non
power down
ICC2N
20
9
20
9
20
9
CKE, CS = VIH,
t
CK = 12 ns
Standby current in non
power down (input signal
stable)
ICC2NS
CKE = VIH, tCK = ∞
Active standby current in
power down
ICC3P
—
—
4
3
—
—
4
3
—
—
4
3
mA
mA
CKE = VIL,
1, 2, 6
t
CK = 12 ns
Active standby current in
power down (input signal
stable)
ICC3PS
CKE = VIL, tCK = ∞ 2, 7
Active standby current in
non power down
ICC3N
—
—
30
15
—
—
30
15
—
—
30
15
mA
mA
CKE, CS = VIH,
CK = 12 ns
1, 2, 4
t
Active standby current in
non power down (input
signal stable)
ICC3NS
CKE = VIH, tCK = ∞ 2, 9
Burst operating current
(CAS latency = 2)
ICC4
ICC4
ICC5
ICC6
—
—
—
—
100
135
220
3
—
—
—
—
100
100
220
3
—
—
—
—
75
mA
tCK = min, BL = 4
1, 2, 5
(CAS latency = 3)
Refresh current
100 mA
220 mA
t
RC = min
3
8
Self refresh current
3
2
1
mA
mA
µA
VIH ≥ VCC – 0.2 V
VIL ≤ 0.2 V
Self refresh current
(L-version)
ICC6
—
2
1
—
2
1
—
Input leakage current
Output leakage current
ILI
–1
–1
–1
0 ≤ Vin ≤ VCC
ILO
–1.5 1.5 –1.5 1.5 –1.5 1.5 µA
0 ≤ Vout ≤ VCC
DQ = disable
Output high voltage
Output low voltage
VOH
VOL
2.4
—
2.4
—
2.4
—
V
V
IOH = –4 mA
—
0.4
—
0.4
—
0.4
IOL = 4 mA
Data Sheet E0082H10
47
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
DC Characteristics (Ta = 0 to +70˚C, VCC, VCCQ = 3.3 V ± 0.3 V, VSS, VSSQ = 0 V)
(HM5225405B)
HM5225405B
-75
-A6
-B6
Parameter
Symbol Min Max Min Max Min Max Unit Test conditions
Notes
Operating current
Burst length = 1
1, 2, 3
(CAS latency = 2)
ICC1
ICC1
—
—
—
110
110
3
—
—
—
95
95
3
—
—
—
75
95
3
mA
mA
mA
tRC = min
(CAS latency = 3)
Standby current in power ICC2P
down
CKE = VIL,
6
7
4
9
t
CK = 12 ns
Standby current in power ICC2PS
down (input signal stable)
—
—
—
2
—
—
—
2
—
—
—
2
mA
mA
mA
CKE = VIL, tCK = ∞
Standby current in non
power down
ICC2N
20
9
20
9
20
9
CKE, CS = VIH,
t
CK = 12 ns
Standby current in non
power down (input signal
stable)
ICC2NS
CKE = VIH, tCK = ∞
Active standby current in
power down
ICC3P
—
—
4
3
—
—
4
3
—
—
4
3
mA
mA
CKE = VIL,
1, 2, 6
t
CK = 12 ns
Active standby current in
power down (input signal
stable)
ICC3PS
CKE = VIL, tCK = ∞ 2, 7
Active standby current in
non power down
ICC3N
—
—
30
15
—
—
30
15
—
—
30
15
mA
mA
CKE, CS = VIH,
CK = 12 ns
1, 2, 4
t
Active standby current in
non power down (input
signal stable)
ICC3NS
CKE = VIH, tCK = ∞ 2, 9
Burst operating current
(CAS latency = 2)
ICC4
ICC4
ICC5
ICC6
—
—
—
—
95
—
—
—
—
95
95
220
3
—
—
—
—
70
95
mA
mA
tCK = min, BL = 4
1, 2, 5
(CAS latency = 3)
Refresh current
130
220
3
220 mA
t
RC = min
3
8
Self refresh current
3
2
1
mA
mA
µA
VIH ≥ VCC – 0.2 V
VIL ≤ 0.2 V
Self refresh current
(L-version)
ICC6
—
2
1
—
2
1
—
Input leakage current
Output leakage current
ILI
–1
–1
–1
0 ≤ Vin ≤ VCC
ILO
–1.5 1.5 –1.5 1.5 –1.5 1.5 µA
0 ≤ Vout ≤ VCC
DQ = disable
Output high voltage
Output low voltage
VOH
VOL
2.4
—
2.4
—
2.4
—
V
V
IOH = –4 mA
—
0.4
—
0.4
—
0.4
IOL = 4 mA
Data Sheet E0082H10
48
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Notes: 1. ICC depends on output load condition when the device is selected. ICC (max) is specified at the
output open condition.
2. One bank operation.
3. Input signals are changed once per one clock.
4. Input signals are changed once per two clocks.
5. Input signals are changed once per four clocks.
6. After power down mode, CLK operating current.
7. After power down mode, no CLK operating current.
8. After self refresh mode set, self refresh current.
9. Input signals are VIH or VIL fixed.
Capacitance (Ta = 25°C, VCC, VCCQ = 3.3 V ± 0.3 V)
Parameter
Symbol
CI1
Min
2.5
2.5
4
Max
3.5
3.8
6.5
Unit
pF
Notes
Input capacitance (CLK)
Input capacitance (Input)
Output capacitance (DQ)
1, 2, 4
1, 2, 4
1, 2, 3, 4
CI2
pF
CO
pF
Notes: 1. Capacitance measured with Boonton Meter or effective capacitance measuring method.
2. Measurement condition: f = 1 MHz, 1.4 V bias, 200 mV swing.
3. DQM, DQMU/DQML = VIH to disable Dout.
4. This parameter is sampled and not 100% tested.
Data Sheet E0082H10
49
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
AC Characteristics (Ta = 0 to +70°C, VCC, VCCQ = 3.3 V ± 0.3 V, VSS, VSSQ = 0 V)
HM5225165B/
HM5225805B/
HM5225405B
-75
-A6
-B6
PC/100
Symbol Symbol Min Max
Parameter
Min Max
Min Max
Unit Notes
System clock cycle time
(CAS latency = 2)
tCK
Tclk
Tclk
Tch
Tcl
10
—
—
—
—
10
10
3
—
—
—
—
15
10
3
—
—
—
—
ns
ns
ns
ns
1
(CAS latency = 3)
CLK high pulse width
CLK low pulse width
tCK
7.5
2.5
2.5
tCKH
tCKL
1
1
3
3
Access time from CLK
(CAS latency = 2)
tAC
tAC
tOH
tLZ
Tac
Tac
Toh
—
—
2.7
2
6
—
—
3
6
—
—
3
8
ns
ns
ns
ns
1, 2
(CAS latency = 3)
5.4
—
—
6
6
Data-out hold time
—
—
—
—
1, 2
CLK to Data-out low
impedance
2
2
1, 2, 3
CLK to Data-out high
impedance
tHZ
—
5.4
—
6
—
6
ns
1, 4
(CAS latency = 2, 3)
Input setup time
tAS, tCS, tDS, Tsi
tCES
1.5
1.5
0.8
67.5
45
—
—
—
—
2
—
—
—
—
2
—
—
—
—
ns
ns
ns
ns
1, 5, 6
CKE setup time for power
down exit
tCESP
Tpde
2
2
1
Input hold time
tAH, tCH, tDH, Thi
tCEH
1
1
1, 6
1
Ref/Active to Ref/Active
command period
tRC
Trc
70
70
Active to Precharge
command period
tRAS
Tras
Trcd
Trp
120000 50
120000 50
120000 ns
1
Active command to column tRCD
command (same bank)
20
—
—
—
—
20
20
20
20
—
—
—
—
20
20
20
20
—
—
—
—
ns
ns
ns
ns
1
Precharge to active
command period
tRP
20
1
Write recovery or data-in to tDPL
precharge lead time
Tdpl
Trrd
15
1
Active (a) to Active (b)
command period
tRRD
15
1
Transition time (rise and fall) tT
Refresh period tREF
1
5
1
5
1
5
ns
—
64
—
64
—
64
ms
Data Sheet E0082H10
50
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Notes: 1. AC measurement assumes tT = 1 ns. Reference level for timing of input signals is 1.5 V.
2. Access time is measured at 1.5 V. Load condition is CL = 50 pF.
3. tLZ (min) defines the time at which the outputs achieves the low impedance state.
4. tHZ (max) defines the time at which the outputs achieves the high impedance state.
5. tCES define CKE setup time to CLK rising edge except power down exit command.
6. tAS/tAH: Address, tCS/tCH: CS, RAS, CAS, WE, DQM, DQMU/DQML.
tDS/tDH: Data-in, tCES/tCEH: CKE.
Test Conditions
•
•
Input and output timing reference levels: 1.5 V
Input waveform and output load: See following figures
2.4 V
I/O
2.0 V
input
0.8 V
0.4 V
CL
t
t
T
T
Data Sheet E0082H10
51
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Relationship Between Frequency and Minimum Latency
HM5225165B/
HM5225805B/
HM5225405B
Parameter
-75
-A6/B6
Frequency (MHz)
133
100
PC/100
Symbol
tCK (ns)
Symbol
7.5
10
Notes
Active command to column command
(same bank)
lRCD
3
2
1
Active command to active command
(same bank)
lRC
9
6
3
2
2
7
5
2
2
2
= [lRAS+ lRP]
1
Active command to precharge command
(same bank)
lRAS
lRP
lDPL
lRRD
1
1
1
1
Precharge command to active command
(same bank)
Write recovery or data-in to precharge
command (same bank)
Tdpl
Active command to active command
(different bank)
Self refresh exit time
lSREX
lAPW
Tsrx
Tdal
1
5
1
4
2
Last data in to active command
(Auto precharge, same bank)
= [lDPL + lRP]
Self refresh exit to command input
lSEC
9
7
= [lRC]
3
Precharge command to high impedance
(CAS latency = 2)
lHZP
lHZP
lAPR
Troh
Troh
2
3
1
2
3
1
(CAS latency = 3)
Last data out to active command
(Auto precharge, same bank)
Last data out to precharge (early precharge)
(CAS latency = 2)
lEP
–1
–2
1
–1
–2
1
(CAS latency = 3)
lEP
Column command to column command
Write command to data in latency
DQM to data in
lCCD
lWCD
lDID
lDOD
lCLE
lRSA
Tccd
Tdwd
Tdqm
Tdqz
Tcke
Tmrd
0
0
0
0
DQM to data out
2
2
CKE to CLK disable
1
1
Register set to active command
1
1
Data Sheet E0082H10
52
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
HM5225165B/
HM5225805B/
HM5225405B
Parameter
-75
-A6/B6
100
Frequency (MHz)
133
PC/100
Symbol
tCK (ns)
Symbol
lCDD
7.5
0
10
0
Notes
CS to command disable
Power down exit to command input
Notes: 1. lRCD to lRRD are recommended value.
lPEC
1
1
2. Be valid [DESL] or [NOP] at next command of self refresh exit.
3. Except [DESL] and [NOP]
Data Sheet E0082H10
53
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Timing Waveforms
Read Cycle
t
CK
t
t
CKH CKL
CLK
CKE
t
RC
V
IH
t
t
RAS
RP
t
RCD
t
t
t
t
t
t
t
t
t
CH
CH
CH
CH
t
CS
CS
CS
CS
CH
CS
CS
t
t
t
t
t
t
t
t
t
t
t
t
CH
CH
CH
CH
CH
CH
CS
CS
CS
CS
CS
CS
RAS
t
t
t
t
CH
CH
CS
CS
CAS
t
t
t
t
CH
CS
CH
CS
t
t
CH
CS
WE
t
t
t
t
t
t
t
t
t
t
t
t
t
t
AH
AH
AH
AH
AH
AH
AH
AS
AS
AS
AS
AS
AS
AS
BS
t
t
t
t
AH
AH
AS
AS
A10
t
t
t
t
AH
AS
AH
AS
Address
t
t
CH
CS
DQM,
DQMU/DQML
DQ (input)
t
t
t
t
AC
AC
AC
HZ
DQ (output)
t
AC
t
OH
t
t
t
CAS latency = 2
OH
OH
OH
t
LZ
Burst length = 4
Bank 0 access
= V or V
Bank 0
Read
Bank 0
Active
Bank 0
Precharge
IH
IL
Data Sheet E0082H10
54
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Write Cycle
t
CK
t
t
CKH CKL
CLK
CKE
t
RC
V
IH
t
t
RAS
RP
t
RCD
t
t
t
t
t
t
CH
CH
CH
CS
CS
CS
t
t
t
t
t
t
t
t
CH
CH
CH
CH
CS
CS
CS
CS
CS
t
t
t
t
CH
CH
CS
CS
RAS
t
t
t
t
t
t
CH
CH
CH
CS
CS
CS
t
t
CH
CS
CAS
WE
t
t
CH
CS
t
t
t
t
t
t
t
t
CH
AH
CH
AH
CS
AS
CS
AS
t
t
t
t
t
t
t
t
AH
AH
AH
AH
AS
AS
AS
AS
BS
t
t
t
t
t
t
AH
AH
AH
AS
AS
AS
A10
t
t
t
t
AH
AH
AS
AS
Address
t
t
t
CH
CS
DQM,
DQMU/DQML
t
t
DH
t
DS
DH
t
t
t
DS
t
DH
DS
DH
DS
DQ (input)
t
DPL
DQ (output)
Bank 0
Precharge
Bank 0
Write
CAS latency = 2
Burst length = 4
Bank 0 access
Bank 0
Active
= V or V
IH
IL
Data Sheet E0082H10
55
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Mode Register Set Cycle
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
CLK
CKE
V
IH
CS
RAS
CAS
WE
BS
code
C: b’
Address
valid
C: b
R: b
DQM,
DQMU/DQML
b+3
b’+1 b’+2 b’+3
b’
DQ (output)
b
High-Z
DQ (input)
l
RSA
l
l
RCD
RP
Output mask
l
= 3
RCD
Precharge
If needed
Mode
register
Set
Bank 3
Active
Bank 3
Read
CAS latency = 3
Burst length = 4
= V or V
IH
IL
Read Cycle/Write Cycle
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20
CLK
CKE
V
IH
Read cycle
RAS-CAS delay = 3
CAS latency = 3
Burst length = 4
CS
RAS
= V or V
IH
IL
CAS
WE
BS
Address
DQM,
DQMU/DQML
R:a
C:a
R:b
C:b
C:b'
C:b"
DQ (output)
DQ (input)
a
a+1 a+2 a+3
b
b+1 b+2 b+3 b' b'+1 b" b"+1 b"+2 b"+3
High-Z
Bank 0
Active
Bank 0
Read
Bank 3
Active
Bank 3 Bank 0
Bank 3
Read
Bank 3
Read
Bank 3
Precharge
Read
Precharge
V
IH
CKE
Write cycle
RAS-CAS delay = 3
CAS latency = 3
Burst length = 4
CS
RAS
= V or V
IH
IL
CAS
WE
BS
Address
DQM,
DQMU/DQML
R:a
C:a
a
R:b
C:b
C:b'
C:b"
High-Z
DQ (output)
DQ (input)
a+1 a+2 a+3
b
b+1 b+2 b+3 b'
b'+1 b" b"+1b"+2 b"+3
Bank 0
Active
Bank 0
Write
Bank 3
Active
Bank 3
Write
Bank 0
Precharge
Bank 3
Write
Bank 3
Write
Bank 3
Precharge
Data Sheet E0082H10
56
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Read/Single Write Cycle
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20
CLK
CKE
V
IH
CS
RAS
CAS
WE
BS
R:a
C:a
R:b
C:a' C:a
a
Address
DQM,
DQMU/DQML
DQ (input)
DQ (output)
a
a+1 a+2 a+3
a
a+1 a+2 a+3
Bank 0
Active
Bank 0
Read
Bank 3
Active
Bank 0 Bank 0
Write Read
Bank 0
Precharge
Bank 3
Precharge
V
IH
CKE
CS
RAS
CAS
WE
BS
R:a
C:a
R:b
C:a
C:b C:c
Address
DQM,
DQMU/DQML
a
b
c
DQ (input)
DQ (output)
a
a+1
a+3
Bank 0
Active
Bank 0
Read
Bank 0
Write
Bank 0 Bank 0
Write Write
Bank 0
Precharge
Bank 3
Active
Read/Single write
RAS-CAS delay = 3
CAS latency = 3
Burst length = 4
= V or V
IH
IL
Data Sheet E0082H10
57
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Read/Burst Write Cycle
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20
CLK
CKE
CS
RAS
CAS
WE
BS
Address
R:a
C:a
R:b
C:a'
DQM,
DQMU/DQML
a
a+1 a+2 a+3
DQ (input)
DQ (output)
a
a+1 a+2 a+3
Bank 0
Active
Bank 0
Read
Bank 3
Active
Clock
suspend
Bank 0
Precharge
Bank 3
Precharge
Bank 0
Write
V
CKE
IH
CS
RAS
CAS
WE
BS
R:a
C:a
R:b
C:a
a
Address
DQM,
DQMU/DQML
a+1 a+2 a+3
DQ (input)
DQ (output)
a
a+1
a+3
Bank 0
Active
Bank 0
Read
Bank 0
Write
Bank 0
Precharge
Bank 3
Active
Read/Burst write
RAS-CAS delay = 3
CAS latency = 3
Burst length = 4
= V or V
IH
IL
Data Sheet E0082H10
58
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Auto Refresh Cycle
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CLK
CKE
V
IH
CS
RAS
CAS
WE
BS
Address
C:a
A10=1
R:a
DQM,
DQMU/DQML
DQ (input)
a
a+1
High-Z
DQ (output)
t
t
RC
t
RP
RC
Refresh cycle and
Read cycle
Active
Bank 0
Read
Bank 0
Auto Refresh
Precharge
If needed
Auto Refresh
RAS-CAS delay = 2
CAS latency = 2
Burst length = 4
= V or V
IH
IL
Self Refresh Cycle
CLK
CKE
CS
l
SREX
CKE Low
RAS
CAS
WE
BS
Address
A10=1
DQM,
DQMU/DQML
DQ (input)
High-Z
DQ (output)
t
t
RP
t
RC
RC
Self refresh cycle
RAS-CAS delay = 3
CAS latency = 3
Burst length = 4
Auto
refresh
Self refresh entry
command
Precharge command
If needed
Next
Self refresh exit
ignore command
or No operation
Next
Self refresh entry
command
clock
clock
enable
enable
= V or V
IH
IL
Data Sheet E0082H10
59
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Clock Suspend Mode
t
t
CES
t
CES
CEH
8
0
1
2
3
4
5
6
7
9
10 11 12 13 14 15 16 17 18 19 20
CLK
CKE
Read cycle
RAS-CAS delay = 2
CAS latency = 2
Burst length = 4
CS
RAS
= V or V
IH
IL
CAS
WE
BS
Address
R:a
C:a
R:b
C:b
DQM,
DQMU/DQML
DQ (output)
DQ (input)
a
a+1 a+2
a+3
b
b+1 b+2 b+3
High-Z
Bank0 Active clock
Active suspend start
Active clock Bank0
suspend end Read
Bank3 Read suspend Read suspend
Bank0
Earliest Bank3
Precharge
Bank3
Active
start
end Read Precharge
CKE
Write cycle
RAS-CAS delay = 2
CAS latency = 2
Burst length = 4
CS
RAS
= V or V
IH
IL
CAS
WE
BS
R:b
a+1
Address
DQM,
DQMU/DQML
DQ (output)
DQ (input)
R:a
C:a
a
C:b
High-Z
a+2
a+3
b
b+1 b+2 b+3
Bank0
Active clock Bank0 Bank3 Write suspend Write suspend Bank3
Earliest Bank3
Precharge
Bank0 Active clock
Active suspend start
Precharge
end Write
supend end Write Active
start
Data Sheet E0082H10
60
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Power Down Mode
CLK
CKE
CS
CKE Low
RAS
CAS
WE
BS
Address
A10=1
R: a
DQM,
DQMU/DQML
DQ (input)
High-Z
DQ (output)
t
RP
Power down cycle
Power down entry
Power down
mode exit
Precharge command
If needed
RAS-CAS delay = 3
CAS latency = 3
Burst length = 4
Active Bank 0
= V or V
IH
IL
Initialization Sequence
53
52
0
1
2
3
4
5
6
7
8
9
10
48
49
50
51
54
55
CLK
V
IH
CKE
CS
RAS
CAS
WE
code
valid
Address
Valid
DQM,
DQMU/DQML
V
IH
High-Z
DQ
t
RP
t
t
RC
t
RC
RSA
Bank active
If needed
All banks
Precharge
Mode register
Set
Auto Refresh
Auto Refresh
Data Sheet E0082H10
61
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Package Dimensions
HM5225165BTT/BLTT
HM5225805BTT/BLTT
HM5225405BTT/BLTT Series (TTP-54D)
Unit: mm
22.22
22.72 Max
54
28
27
1
0.80
0.13
+0.10
*0.30
–0.05
M
0.28 ± 0.05
0.80
11.76 ± 0.20
0.91 Max
0° – 5°
0.50 ± 0.10
0.10
Hitachi Code
TTP-54D
JEDEC
EIAJ
—
—
*Dimension including the plating thickness
Base material dimension
Weight (reference value) 0.53 g
Data Sheet E0082H10
62
HM5225165B/HM5225805B/HM5225405B-75/A6/B6
Cautions
1. Elpida Memory, Inc. neither warrants nor grants licenses of any rights of Elpida Memory, Inc.’s or any
third party’s patent, copyright, trademark, or other intellectual property rights for information contained in
this document. Elpida Memory, Inc. bears no responsibility for problems that may arise with third party’s
rights, including intellectual property rights, in connection with use of the information contained in this
document.
2. Products and product specifications may be subject to change without notice. Confirm that you have
received the latest product standards or specifications before final design, purchase or use.
3. Elpida Memory, Inc. makes every attempt to ensure that its products are of high quality and reliability.
However, contact Elpida Memory, Inc. before using the product in an application that demands especially
high quality and reliability or where its failure or malfunction may directly threaten human life or cause
risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation,
traffic, safety equipment or medical equipment for life support.
4. Design your application so that the product is used within the ranges guaranteed by Elpida Memory, Inc.
particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation
conditions and other characteristics. Elpida Memory, Inc. bears no responsibility for failure or damage
when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally
foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as
fail-safes, so that the equipment incorporating Elpida Memory, Inc. product does not cause bodily injury,
fire or other consequential damage due to operation of the Elpida Memory, Inc. product.
5. This product is not designed to be radiation resistant.
6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without
written approval from Elpida Memory, Inc..
7. Contact Elpida Memory, Inc. for any questions regarding this document or Elpida Memory, Inc.
semiconductor products.
Data Sheet E0082H10
63
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明