MAFA-PA-1014-S21-E-3 [EMCORE]
Optical Preamplifier;型号: | MAFA-PA-1014-S21-E-3 |
厂家: | EMCORE CORPORATION |
描述: | Optical Preamplifier |
文件: | 总4页 (文件大小:801K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MAFA 1014-PA Optical Preamplifier
Erbium Doped Fiber Preamplifier
DATASHEET | SEPTEMBER 2013
FIBER OPTICS
EMCORE’s MAFA 1014-PA Optical Preamplifier Erbium Doped Fiber Gain Block Module is
an ideal building block for system integrators to extend the fiber link for long-haul signal
transport. The MAFA 1014-PA Optical Preamplifier series gain blocks are designed to meet
the most demanding noise performance requirements of fiber optic communications and
control systems and performs all the functions required of an optical preamplifier for system
integration.
The MAFA 1014-PA Optical Preamplifier provides output optical isolation for stable, low
noise operation. The output optical signal power level is detected for monitoring and
control. The very low level input optical signal is amplified with active output power control
for constant current mode operation.
Applications
The compact mechanical footprint of the MAFA 1014-PA Optical Preamplifier allows using
this unit to be installed in small space environments.
CATV Systems
Long Distance RF/Microwave Fiber
Optic Communication Links
Sensing and Control Systems
High-Performance Supertrunking Links
High Power Distribution Networks
Redundant Ring Architectures
FTTx Networks
General and Mechanical Specifications
Parameter
Operating Wavelength
Operating Case Temperature
Storage Temperature
Operating Humidity
Min
Typ
Max
Units
nm
°C
Comments
Standard
1532
-
1565
0
-40
20
-
-
50
85
85
-
Standard*
-
°C
Standard
-
%
Non-condensing
All Versions**
User Specified
All Versions
Features
Voltage Supply Range
Optical Connectors
+12/+5/+3.3
SC; FC; E2000
70 x 90 x 15
VDC
-
Full Function Fiber Optic pre-Amplifier
Low Noise Figure (NF Typ < 3.3 dB)
Pin > -45 dBm
-
-
Dimensions (mm)
-
-
Mm
* - Extended temperature range of – 40ºC to +75ºC is also possible
** Transient Pulse to +X.X VDC + 5% for < 100 msec
Pout (saturated): ≈ +14 dBm
Small Signal Gain > 37 dB
Electrical power must be applied to the unit only after launching input optical
Low Electrical Power Consumption
Output Isolation > 40 dB
Polarization Dependant Gain < 0.1 dB
Polarization Mode Dispersion < 0.2 ps
Output Return Losses < -40 dB
Output Residual Pump Power < -40 dBm
|
REV 2013.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
MAFA 1014-PA Optical Preamplifier
Erbium Doped Fiber Preamplifier
DATASHEET | SEPTEMBER 2013
FIBER OPTICS
Optical/Electrical Characteristics1
Property
Unit
Limit
Model 1400
Comments (Note 1)
Operating Input Power
Operating Input Power
Saturated Output Power
Noise Figure
Pin (dBm)
Pin (dBm)
Pout (dBm)
NF (dB)
Max
Min
0
-
-45
-
Nominal
Max
14 +/- .25
3.3 dB
+/- 0.1
(Notes 2,3)
(Note 4)
(Note 5)
Output Power Stability
(dB)
Max
Power Consumption
(Steady state)
Psys(W)
Max
2
70°C Case
Notes:
1. Unless stated otherwise, all specifications apply over the full operating temperature and humidity ranges
2. Measurement variations
3. Measured @ 1550 nm and Pin = -4 dBm
4. Measure @ 1550 nm and Pin = -30 dBm
5. Over polarization and temperature
Outline Drawing (dimensions in mm)
|
REV 2013.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
MAFA 1014-PA Optical Preamplifier
Erbium Doped Fiber Preamplifier
DATASHEET | SEPTEMBER 2013
FIBER OPTICS
Compliance and Reliability Information
FCC: Subpart B. Part 15 class “A”: Unintentional Radiators
EN 55013: Sound and Television Broadcast receivers and associated equipment – Radio disturbance characteristics- limits and methods
of measurements – Electric Field Radiation Emissions (2001)
Fit Rate: 90% level of confidence - 290 @ 25°C
Electrical Connector Pinout
PIN #
Designation
PIN #
Designation
1
2
+12 VDC/+5 VDC/+3.3 VDC
+12 VDC/+5 VDC/+3.3 VDC
+12 VDC/+5 VDC/+3.3 VDC
+12 VDC/+5 VDC/+3.3 VDC
GND
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
LED_Laser_ON
N/A
3
Pump_Bias_Alarm *
4
Loss_Input_Power *
5
Loss_Output_Power *
6
GND
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
7
RS232_Rx
8
RS232_Tx
9
GND
10
11
12
13
14
15
GND
LED_Comm
EDFA_Reset
EDFA_Disable
Pout_Mute
EDFA_Temp_Alarm *
* - software adjustable parameters; logic levels (low / high) TBD
Ordering Information
MAFA-PA-1014 -
-
-
Connector Option
SC1 - SC/APC
S21 - SC/PC
Temp Options
Voltage Options
S – Standard
1 - +12 VDC
E – Extended
2 - +5 VDC
FC1- FC/APC
-
-
-
3 - +3.3 VDC
FC2- FC/PC
-
-
EC1-E2000/APC
Example:
MAFA-PA-1014-SC1-S-2: 14 dBm pre-amp gain block with SC/APC optical connectors, standard temperature range, +5 VDC power
supply
|
REV 2013.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
MAFA 1014-PA Optical Preamplifier
Erbium Doped Fiber Preamplifier
DATASHEET | SEPTEMBER 2013
FIBER OPTICS
Laser Safety Information
This component product does not meet the applicable requirements of 21 CFR 1010 & 1040 and is classified as a Class IIIb laser product
based on the maximum optical output power defined below. During use as intended, the laser energy is fully contained within the fiber
network such that there is no accessible laser radiation and would meet the requirements for a Class I laser product.
Wavelength = 1532 ~ 1565 nm (dependent on input source)
Maximum Output Power = 200 mW
|
REV 2013.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
相关型号:
©2020 ICPDF网 联系我们和版权申明