B41201B4479M000 [EPCOS]
Aluminum electrolytic capacitors; 铝电解电容器
| 型号： | B41201B4479M000 |
| 厂家： | 
EPCOS |
| 描述： | Aluminum electrolytic capacitors |
| 文件： | 总13页 (文件大小：579K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Aluminum electrolytic capacitors
Alu-X product lines
4-pin snap-in capacitors
Series/Type:
B41201, B43201
Data Sheet
Date:
April 2008
© EPCOS AG 2008. Reproduction, publication and dissemination of this publication and the infor-
mation contained therein without EPCOS’ prior express consent is prohibited.
4-pin snap-in capacitors
B41201, B43201
Standard series – 85 °C
General-purpose grade capacitors
Applications
■ Professional switch-mode power supplies
Features
■ High ripple current capability
■ RoHS-compatible
■ Load life of 2000 h at 85 °C
Construction
■ Aluminum case, fully insulated
■ Charge/discharge-proof
■ Minus pole marking on the insulating sleeve
■ Case with safety vent
Please read Cautions and warnings and
Important notes at the end of this document.
2
04/08
4-pin snap-in capacitors
B41201, B43201
Standard series – 85 °C
Specifications and characteristics in brief
Rated voltage VR
10 … 500 V DC
Operating tempera-
ture range
V
V
R ≤ 250 V DC: –40 °C … +85 °C
R ≥ 315 V DC: –25 °C … +85 °C
Rated capacitance CR 100 … 68000 µF
(20 °C, 120 Hz)
Capacitance tolerance ±20%
M
Load life
2000 h
Requirements:
(85 °C, VR, IAC,R
)
∆C/C ≤ ±20% of initial value
tan δ ≤ 2 times initial specified limit
Ileak ≤ initial specified limit
Leakage current Ileak
(20 °C, after 5 minutes)
CR VR
⎛
⎝
⎞
⎠
------- ------
I
leak ≤ 0.02 µA
µF
V
10
16
25 35 50 63
80
100 160... 250... 450 ...
Dissipation factor
(max.)
VR
(V DC)
200
400
500
(20 °C, 120 Hz)
0.50 0.50 0.40 0.40 0.30 0.25 0.20 0.15 0.12 0.15 0.20
tan δ
10
5
16 ... 160 200 ... 250 315 ... 400 450 ... 500
Low temperature sta-
bility (impedance ratio)
(120 Hz)
VR (V DC)
4
7
8
8
Z(–25 °C)
--------------------------
Z(+20 °C)
18
15
12
–
–
Z(–40 °C)
Z(+20 °C)
---------------------------
Shelf life
After storage for 1000 h at 85 °C, the capacitors shall meet the requirement
of load life test after reforming process. After test: VR to be applied for
30 minutes, 24 to 48 hours before measurement.
Frequency multiplier
for rated ripple current
50 Hz
0.95
0.95
0.90
+40 °C
2.1
120 Hz 1 kHz
10 kHz
1.15
1.30
1.50
+85 °C
1.0
20 kHz
1.15
≤50 V
1.00
1.00
1.00
1.10
1.16
1.20
63 ... 100 V
≥160 V
1.33
1.55
Temperature multiplier
for rated ripple current
+55 °C +70 °C
<160 V
≥160 V
2.1
1.5
1.5
1.3
1.7
1.0
Please read Cautions and warnings and
Important notes at the end of this document.
3
04/08
4-pin snap-in capacitors
B41201, B43201
Standard series – 85 °C
Dimensional drawing
Plus pole marking
Mounting holes
+
-
Minus pole marking
2±0.1
22.5±0.1
Safety vent
on the case wall
0.8+0.2
_0.1
1.5±0.2
KAL1136-W-E
Overview of available types B41201
VR
(V DC)
10
16
25
35
Case dimensions d × l (mm)
CR (µF)
12000
15000
18000
22000
35 × 30
35 × 35
35 × 40
35 × 45
35 × 30
35 × 35
35 × 40
35 × 45
27000
33000
39000
47000
56000
68000
35 × 25
35 × 30
35 × 35
35 × 40
35 × 45
35 × 50
35 × 25
35 × 30
35 × 30
35 × 35
35 × 40
Please read Cautions and warnings and
Important notes at the end of this document.
4
04/08
4-pin snap-in capacitors
B41201, B43201
Standard series – 85 °C
Overview of available types B41201
VR
(V DC)
50
63
80
100
Case dimensions d × l (mm)
CR (µF)
2700
35 × 30
35 × 35
35 × 35
35 × 40
35 × 45
3300
3900
4700
5600
35 × 25
35 × 25
35 × 30
35 × 30
35 × 35
35 × 40
35 × 45
35 × 50
35 × 30
35 × 30
35 × 30
35 × 35
35 × 40
35 × 45
35 × 30
35 × 35
35 × 40
35 × 45
6800
8200
10000
12000
15000
18000
Overview of available types B43201
VR
(V DC)
160
200
250
315
Case dimensions d × l (mm)
CR (µF)
180
35 × 20
35 × 20
35 × 25
35 × 30
35 × 30
35 × 35
35 × 40
35 × 45
35 × 50
220
270
330
35 × 20
35 × 20
35 × 25
35 × 25
35 × 30
35 × 35
35 × 40
35 × 45
35 × 50
390
35 × 20
470
35 × 20
35 × 20
35 × 25
35 × 30
35 × 30
35 × 35
35 × 40
35 × 45
560
35 × 20
35 × 20
35 × 25
35 × 25
35 × 30
35 × 35
35 × 40
680
820
1000
1200
1500
1800
Please read Cautions and warnings and
Important notes at the end of this document.
5
04/08
4-pin snap-in capacitors
B41201, B43201
Standard series – 85 °C
Overview of available types B43201
VR
(V DC)
350
400
450
500
Case dimensions d × l (mm)
CR (µF)
100
35 × 20
35 × 20
35 × 25
35 × 25
35 × 30
35 × 35
35 × 40
35 × 45
35 × 50
120
150
180
220
270
330
390
470
560
680
35 × 20
35 × 25
35 × 25
35 × 30
35 × 30
35 × 35
35 × 40
35 × 45
35 × 20
35 × 35
35 × 25
35 × 30
35 × 35
35 × 40
35 × 45
35 × 50
35 × 45
35 × 50
Please read Cautions and warnings and
Important notes at the end of this document.
6
04/08
4-pin snap-in capacitors
B41201, B43201
Standard series – 85 °C
Technical data and ordering codes B41201
VR
CR
120 Hz
20 °C
Case
dimensions
d × l
IAC,R
120 Hz
85 °C
A
Ordering code
V DC µF
mm
10 33000
35 × 25
35 × 30
35 × 30
35 × 35
35 × 40
5.81
B41201D3339M000
B41201C3399M000
B41201C3479M000
B41201B3569M000
B41201A3689M000
39000
47000
56000
68000
6.38
6.62
7.18
7.76
16 27000
33000
35 × 25
35 × 30
35 × 35
35 × 40
35 × 45
35 × 50
5.80
6.41
6.96
7.54
8.08
8.63
B41201C4279M000
B41201B4339M000
B41201B4399M000
B41201B4479M000
B41201A4569M000
B41201A4689M000
39000
47000
56000
68000
25 22000
27000
35 × 30
35 × 35
35 × 40
35 × 45
5.51
6.12
6.74
7.35
B41201B5229M000
B41201B5279M000
B41201B5339M000
B41201A5399M000
33000
39000
35 12000
15000
35 × 30
35 × 35
35 × 40
35 × 45
5.24
5.88
6.46
7.07
B41201B7129M000
B41201B7159M000
B41201B7189M000
B41201A7229M000
18000
22000
50
4700
5600
6800
35 × 25
35 × 25
35 × 30
35 × 30
35 × 35
35 × 40
35 × 45
35 × 50
4.19
4.44
5.04
5.26
5.97
6.55
7.20
7.74
B41201D6478M000
B41201D6568M000
B41201D6688M000
B41201C6828M000
B41201B6109M000
B41201B6129M000
B41201A6159M000
B41201A6189M000
8200
10000
12000
15000
18000
63
4700
5600
6800
8200
10000
12000
35 × 30
35 × 30
35 × 30
35 × 35
35 × 40
35 × 45
4.19
4.70
5.04
5.53
6.25
6.83
B41201D8478M000
B41201C8568M000
B41201C8688M000
B41201B8828M000
B41201B8109M000
B41201A8129M000
Please read Cautions and warnings and
Important notes at the end of this document.
7
04/08
4-pin snap-in capacitors
B41201, B43201
Standard series – 85 °C
Technical data and ordering codes B41201
VR
CR
120 Hz
20 °C
Case
dimensions
d × l
IAC,R
120 Hz
85 °C
A
Ordering code
V DC µF
mm
80
4700
35 × 30
35 × 35
35 × 40
35 × 45
5.27
B41201C0478M000
B41201B0568M000
B41201A0688M000
B41201A0828M000
5600
6800
8200
5.81
5.46
6.91
100
2700
3300
3900
4700
5600
35 × 30
35 × 35
35 × 35
35 × 40
35 × 45
4.37
4.85
5.27
5.80
6.34
B41201C9278M000
B41201C9338M000
B41201B9398M000
B41201B9478M000
B41201A9568M000
Please read Cautions and warnings and
Important notes at the end of this document.
8
04/08
4-pin snap-in capacitors
B41201, B43201
Standard series – 85 °C
Technical data and ordering codes B43201
VR
CR
120 Hz
20 °C
Case
dimensions
d × l
IAC,R
120 Hz
85 °C
A
Ordering code
V DC µF
mm
160
560
680
820
1000
1200
1500
1800
35 × 20
35 × 20
35 × 25
35 × 25
35 × 30
35 × 35
35 × 40
2.12
B43201D1567M000
B43201D1687M000
B43201D1827M000
B43201D1108M000
B43201C1128M000
B43201B1158M000
B43201A1188M000
2.33
2.73
3.01
3.26
3.83
4.39
200
250
315
390
470
560
680
820
1000
1200
1500
1800
35 × 20
35 × 20
35 × 20
35 × 25
35 × 30
35 × 30
35 × 35
35 × 40
35 × 45
1.77
1.94
2.25
2.48
2.88
3.18
3.43
4.01
4.58
B43201D2397M000
B43201D2477M000
B43201D2567M000
B43201D2687M000
B43201D2827M000
B43201B2108M000
B43201B2128M000
B43201B2158M000
B43201A2188M000
330
390
470
560
680
35 × 20
35 × 20
35 × 25
35 × 25
35 × 30
35 × 35
35 × 40
35 × 45
35 × 50
1.62
1.77
2.06
2.25
2.62
3.03
3.50
3.74
4.35
B43201I2337M000
B43201I2397M000
B43201I2477M000
B43201I2567M000
B43201H2687M000
B43201G2827M000
B43201G2108M000
B43201F2128M000
B43201F2158M000
820
1000
1200
1500
180
220
270
330
390
470
560
680
820
35 × 20
35 × 20
35 × 25
35 × 30
35 × 30
35 × 35
35 × 40
35 × 45
35 × 50
1.20
1.33
1.56
1.83
1.99
2.29
2.62
3.01
3.44
B43201D0187M000
B43201D0227M000
B43201D0277M000
B43201D0337M000
B43201C0397M000
B43201B0477M000
B43201A0567M000
B43201A0687M000
B43201A0827M000
Please read Cautions and warnings and
Important notes at the end of this document.
9
04/08
4-pin snap-in capacitors
B41201, B43201
Standard series – 85 °C
Technical data and ordering codes B43201
VR
CR
120 Hz
20 °C
Case
dimensions
d × l
IAC,R
120 Hz
85 °C
A
Ordering code
V DC µF
mm
350
180
220
270
330
390
470
560
680
35 × 20
35 × 35
35 × 25
35 × 30
35 × 35
35 × 40
35 × 45
35 × 50
1.20
B43201D4187M000
B43201D4227M000
B43201C4277M000
B43201C4337M000
B43201B4397M000
B43201B4477M000
B43201A4567M000
B43201A4687M000
1.41
1.65
1.83
2.09
2.40
2.73
3.13
400
150
180
220
270
330
390
470
560
35 × 20
35 × 25
35 × 25
35 × 30
35 × 30
35 × 35
35 × 40
35 × 45
1.09
1.28
1.41
1.65
1.83
2.09
2.40
2.73
B43201D9157M000
B43201D9187M000
B43201D9227M000
B43201C9277M000
B43201C9337M000
B43201B9397M000
B43201B9477M000
B43201A9567M000
450
100
120
150
180
220
270
330
390
470
35 × 20
35 × 20
35 × 25
35 × 25
35 × 30
35 × 35
35 × 40
35 × 45
35 × 50
0.68
0.75
0.89
0.98
1.14
1.33
1.54
1.74
1.99
B43201D5107M000
B43201D5127M000
B43201D5157M000
B43201C5187M000
B43201C5227M000
B43201B5277M000
B43201B5337M000
B43201A5397M000
B43201A5477M000
500
270
330
35 × 45
35 × 50
1.45
1.66
B43201A6277M000
B43201A6337M000
Please read Cautions and warnings and
Important notes at the end of this document.
10 04/08
Cautions and warnings
General
Also see “Important notes” on page 13.
1
Aluminum electrolytic capacitors have a bi-polar structure. This is marked on the body of the
capacitor. A capacitor must not be mounted with reversed polarity. The application of an AC
or reverse voltage may cause a short circuit or damage the capacitor. Bi-polar capacitors
must not be used in AC applications, where the polarity may be reversed in the circuits or is
unknown.
2
3
The DC voltage applied to the capacitor terminal must not exceed its rated operating voltage,
as this will result in a rapid increase of the leakage current and may damage the capacitor. It
is recommended to operate the capacitor at 70–80% of its rated voltage to optimize its serv-
ice life.
The ripple current applied to the capacitor must be within the permitted range. An excessive
ripple current leads to impaired electrical properties and may damage the capacitor. Note that
the sum of the peak values of the ripple voltage and the DC operating voltage must not ex-
ceed the rated DC voltage.
4
5
Capacitors must be used within their permitted range of operating temperature. Operation at
room temperature optimizes their service life.
Capacitors with case diameter ≥8 mm are equipped with a safety vent. In capacitors fitted
with a lead or soldering lug, the safety vent is usually located at the base of the case. It needs
sufficient space around it to operate optimally. The following dimensions are recommended:
for case diameter d = 8 to 16 mm, more than 2 mm; for d =18 to 35 mm, more than 3 mm;
and for d = 42 mm or more, more than 5 mm.
6
Capacitors should not be mounted with the safety vent face down on the board. Do not locate
any wire or copper trace near the safety vent. Do not reverse the voltage, as this may result
in excess pressure and the leakage of electrolyte.
7
8
Gas is released through the safety vent when the pressure inside the capacitor is too high. A
gaseous liquid around the safety vent does not indicate a leakage of electrolyte.
The capacitor should be stored under conditions of normal temperature and in a non-acid,
non-alkali environment of normal humidity. Exposure to high temperatures, for example un-
der direct sunlight, will reduce its operating life. If the capacitor is stored in an environment
containing acids or alkalis, the solderability of the leads may be affected.
9
The leakage current of an aluminum electrolytic capacitor may increase after a long period
of storage. After such storage, the capacitor must be aged by applying the rated operating
voltage for 6–8 hours before use.
10
Manual soldering:
a
Soldering must be performed within the specified conditions.
Bit temperature: 350 °C; application time of soldering iron: 3 seconds.
Ensure that the soldering iron does not touch any part of the capacitor body.
b
Please read Cautions and warnings and
Important notes at the end of this document.
11 04/08
Cautions and warnings
11
Do not apply excessive force to the leads and terminals. Do not move the capacitor after sol-
dering it onto the PC board and do not carry the PC board by gripping the capacitor. Observe
the following rules to prevent undue stress to the capacitor:
a
b
Do not tilt or bend the capacitor after soldering.
Ensure that the terminal spacing matches the corresponding hole spacing on the PC
board.
12
13
The aluminum case is not insulated from the cathode. Do not place a conductor under the
aluminum capacitors on the PC board as this may cause a short circuit. The case and top of
capacitors used in switched mode power supplies have a high-voltage-resistant heat shrink
sleeve to ensure safe usage.
The leads of capacitors with a case diameter exceeding 14 mm cannot be used for fixing.
Please read Cautions and warnings and
Important notes at the end of this document.
12 04/08
Important notes
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As
a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or failure
before the end of their usual service life cannot be completely ruled out in the current state
of the art, even if they are operated as specified. In customer applications requiring a very
high level of operational safety and especially in customer applications in which the malfunction
or failure of an electronic component could endanger human life or health (e.g. in accident
prevention or life-saving systems), it must therefore be ensured by means of suitable design of
the customer application or other action taken by the customer (e.g. installation of protective
circuitry or redundancy) that no injury or damage is sustained by third parties in the event of
malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We alsoreservetherighttodiscontinueproductionanddeliveryofproducts. Consequently,
we cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in case of individual agreements deviating from the foregoing for
customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK,
MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap,
SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks
registered or pending in Europe and in other countries. Further information will be found on
the Internet at www.epcos.com/trademarks.
13 04/08
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明