B41866C4567M001 [EPCOS]
Single-ended capacitors; 单端电容器
| 型号： | B41866C4567M001 |
| 厂家： | 
EPCOS |
| 描述： | Single-ended capacitors |
| 文件： | 总30页 (文件大小：724K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Aluminum electrolytic capacitors
Single-ended capacitors
Series/Type:
B41866
Date:
December 2006
EPCOS AG 2007. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Single-ended capacitors
B41866
High ripple current ꢀ 125 °C
Long-life grade capacitors for automotive electronics
Applications
High-reliability equipment in industrial and automotive
electronics
High-temperature environments
Automotive electronics
Features
High reliability and long useful life
High ripple current capability
Wide temperature range up to 125 °C
Construction
Charge-discharge proof, polar
Aluminum case with insulating sleeve
Minus pole marking on the insulating sleeve
Case with safety vent
Delivery mode
Terminal configurations and packing:
Bulk
Taped, Ammo pack
Cut
Kinked
PAPR (protection against polarity reversal):
crimped leads, J leads, bent leads
Refer to chapter "Single-ended capacitors ꢀ Taping, packing
and lead configurations" for further details and ordering
example.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 2 of 30
B41866
High ripple current ꢀ 125 °C
Specifications and characteristics in brief
Rated voltage VR
10 ... 63 V DC
1.15 ꢁ VR
Surge voltage VS
Rated capacitance CR
Capacitance tolerance
10 ... 10000 µF
±20% ꢂ M
Dissipation factor tan δ
(20 °C, 120 Hz)
For capacitance higher than 1000 µF add 0.02 for every increase of
1000 µF.
VR (V DC)
10
16...25
0.17
35
50
63
tan δ (max.)
0.20
0.12
0.10
0.15
Leakage current Ileak
(20 °C, 5 min)
or 3 µA, whichever is greater
Self-inductance ESL
Diameter (mm)
ESL (nH)
8 ... 12.5 16
20 26
18
34
Useful life
125 °C, VR, IAC,R
1000 h for ≤ 10mm
2000 h for ≥ 12.5 mm
Requirements
∆C/C
tan δ
Ileak
≤ ±35% of initial value
≤ 3 times initial specified limit
≤ initial specified limit
Voltage endurance test
125 °C, VR
1000 h for ≤ 10mm
2000 h for ≥ 12.5 mm
Post test requirements
∆C/C
tan δ
Ileak
≤ ±30% of initial value
≤ 2 times initial specified limit
≤ initial specified limit
Vibration resistance test To IEC 60068-2-6, test Fc:
Displacement amplitude 0.75 mm, frequency range 10 … 2000 Hz,
acceleration max. 20 g, duration 3 × 2 h.
Capacitor rigidly clamped by the aluminum case.
IEC climatic category
Sectional specification
To IEC 60068-1:
55/125/56 (ꢀ55 °C/+125 °C/56 days damp heat test)
AEC-Q200, IEC 60384-4
Please read Cautions and warnings and
Important notes at the end of this document.
Page 3 of 30
B41866
High ripple current ꢀ 125 °C
Dimensional drawings
With stand-off rubber seal
With flat rubber seal
Diameters (mm): 8, 10, 12.5, 16, 18
Diameter (mm): 8
Dimensions and weights
Dimensions (mm)
Approx. weight
d +0.5
8
l
a ±0.5
3.5
5.0
5.0
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
b
g
11.5 +1.5
12.5 +1.0
16 +1.0
20 +2.0
20 +2.0
25 +2.0
40 +2.0
20 +2.0
25 +2.0
31.5 +2.0
20 +2.0
25 +2.0
31.5 +2.0
35 +2.0
40 +2.0
0.60 ±0.05
0.60 ±0.05
0.60 ±0.05
0.60 ±0.05
0.60 ±0.05
0.60 ±0.05
0.80 ±0.05
0.80 ±0.05
0.80 ±0.05
0.80 ±0.05
0.80 ±0.1
0.80 ±0.1
0.80 ±0.1
0.80 ±0.1
0.80 ±0.1
1.0
1.6
1.9
2.6
3.6
4.5
7.4
5.5
7.5
7.8
8.0
9.0
11.0
13.0
16.0
10
10
10
12.5
12.5
12.5
16
16
16
18
18
18
18
18
Please read Cautions and warnings and
Important notes at the end of this document.
Page 4 of 30
B41866
High ripple current ꢀ 125 °C
Overview of available types
VR (V DC)
10
16
25
35
50
63
Case dimensions d × l (mm)
CR (µF)
10
8
8
8
8
8
8
8
8
8
8
8
8
× 11.5
× 11.5
× 11.5
× 11.5
× 11.5
× 11.5
× 11.5
12
15
18
22
27
33
8
× 11.5
39
× 11.5 10 × 12.5
× 11.5 10 × 12.5
× 11.5 10 × 12.5
× 11.5 10 × 16
× 11.5 10 × 16
47
56
68
82
100
120
150
180
220
270
330
390
470
8
8
8
8
8
8
8
× 11.5
× 11.5
× 11.5
× 11.5
× 11.5
8
8
8
8
8
× 11.5
× 11.5
8
8
× 11.5 10 × 12.5 10 × 16
× 11.5 10 × 16
10 × 16
10 × 16
10 × 20
12.5 × 20
12.5 × 20
12.5 × 20
12.5 × 25
16 × 20
× 11.5 10 × 12.5 10 × 16
× 11.5 10 × 12.5 10 × 20
× 11.5 10 × 12.5 10 × 20
× 11.5 10 × 12.5 10 × 16
× 11.5 10 × 12.5 10 × 16
10 × 20
12.5 × 20
12.5 × 25
8
8
8
× 11.5
× 11.5 10 × 12.5 10 × 16
× 11.5 10 × 12.5 10 × 16
10 × 20
10 × 20
12.5 × 25
16 × 20
560
680
10 × 12.5 10 × 12.5 10 × 20
12.5 × 20
12.5 × 20
16 × 20
16 × 25
16 × 20
10 × 16
10 × 16
10 × 20
12.5 × 40
16 × 25
18 × 20
820
10 × 16
10 × 16
10 × 16
10 × 20
12.5 × 20
12.5 × 20
12.5 × 25
16 × 20
16 × 25
16 × 25
18 × 20
16 × 31.5
1000
16 × 31.5 16 × 31.5
18 × 25
1200
1500
10 × 20
10 × 20
12.5 × 20
12.5 × 25
12.5 × 25
12.5 × 25
18 × 31.5 18 × 31.5
16 × 25
18 × 20
18 × 35
18 × 35
1800
12.5 × 20
12.5 × 25
16 × 20
16 × 31.5 18 × 40
18 × 25
18 × 40
Please read Cautions and warnings and
Important notes at the end of this document.
Page 5 of 30
B41866
High ripple current ꢀ 125 °C
VR (V DC)
10
16
25
35
50
63
Case dimensions d × l (mm)
CR (µF)
2200
12.5 × 20
12.5 × 25
16 × 20
12.5 × 40
16 × 25
18 × 20
18 × 31.5
2700
16 × 25
18 × 20
16 × 31.5 18 × 35
3300
3900
4700
16 × 20
16 × 25
18 × 25
18 × 25
18 × 31.5
18 × 31.5 18 × 40
18 × 35
16 × 25
18 × 20
18 × 40
5600
6800
16 × 31.5 18 × 35
18 × 31.5 18 × 40
18 × 31.5
8200
10000
18 × 40
Other voltage and capacitance ratings are available upon request.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 6 of 30
B41866
High ripple current ꢀ 125 °C
Technical data and ordering codes
CR Case ESRmax ESRmax ESRmax Zmax
IAC,R
IAC,max
Ordering code
120 Hz dimensions 10 kHz 120 Hz 10 kHz 100 kHz 100 kHz 100 kHz (composition see
20 °C d × l ꢀ40 °C 20 °C 20 °C 20 °C 125 °C 105 °C below)
µF mm mA mA
VR = 10 V DC
Ω
Ω
Ω
Ω
330
390
470
8
8
8
× 11.5 5.170 0.766 0.646 0.573
× 11.5 5.170 0.648 0.646 0.573
× 11.5 5.170 0.538 0.646 0.573
297
297
297
450
714
714
714
875
875
1105
1105
1358
1895
2279
2279
2190
2822
3178
3178
4244
416
416
416
B41866C3337M***
B41866C3397M***
B41866C3477M***
B41866C3567M***
B41866C3687M***
B41866C3827M***
B41866C3108M***
B41866C3128M***
B41866C3158M***
B41866C3188M***
B41866C3228M***
B41866C3278M***
B41866C3338M***
B41866C3398M***
B41866C3478M***
B41866D3478M***
B41866C3568M***
B41866C3688M***
B41866C3828M***
B41866C3109M***
560 10 × 12.5 2.980 0.451 0.373 0.336
630
680 10 × 16
820 10 × 16
1000 10 × 16
1200 10 × 20
1500 10 × 20
1800 12.5 × 20
2200 12.5 × 20
2700 12.5 × 25
3300 16 × 20
3900 16 × 25
4700 16 × 25
4700 18 × 20
1.404 0.372 0.175 0.160
1.404 0.308 0.175 0.160
1.404 0.253 0.175 0.160
1.070 0.211 0.134 0.127
1.070 0.168 0.134 0.127
0.881 0.140 0.110 0.104
0.881 0.126 0.110 0.104
0.710 0.103 0.089 0.082
0.401 0.092 0.050 0.046
0.314 0.078 0.039 0.037
0.314 0.070 0.039 0.037
0.341 0.070 0.043 0.040
1000
1000
1000
1225
1225
1546
1546
1901
2652
3190
3190
3066
3950
4450
4450
5941
5600 16 × 31.5 0.249 0.063 0.031 0.029
6800 18 × 31.5 0.226 0.056 0.028 0.027
8200 18 × 31.5 0.226 0.052 0.028 0.027
10000 18 × 40
0.153 0.048 0.019 0.018
VR = 16 V DC
100
120
150
180
220
270
330
8
8
8
8
8
8
8
× 11.5 5.170 2.147 0.646 0.573
× 11.5 5.170 1.789 0.646 0.573
× 11.5 5.170 1.432 0.646 0.573
× 11.5 5.170 1.193 0.646 0.573
× 11.5 5.170 0.976 0.646 0.573
× 11.5 5.170 0.795 0.646 0.573
× 11.5 5.170 0.651 0.646 0.573
297
297
297
297
297
297
297
450
416
416
416
416
416
416
416
630
B41866C4107M***
B41866C4127M***
B41866C4157M***
B41866C4187M***
B41866C4227M***
B41866C4277M***
B41866C4337M***
B41866C4397M***
390 10 × 12.5 2.980 0.551 0.373 0.336
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for ≥ 10 mm)
002 = for cut leads, bulk (for ≥ 10 mm)
003 = for crimped leads, blister (for ≥ 16 mm)
004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm)
012 = for bent 90° leads, blister (for 16 and 18 mm)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 7 of 30
B41866
High ripple current ꢀ 125 °C
Technical data and ordering codes
CR Case ESRmax ESRmax ESRmax Zmax
IAC,R
IAC,max
Ordering code
120 Hz dimensions 10 kHz 120 Hz 10 kHz 100 kHz 100 kHz 100 kHz (composition see
20 °C d × l ꢀ40 °C 20 °C 20 °C 20 °C 125 °C 105 °C below)
µF mm mA mA
VR = 16 V DC
Ω
Ω
Ω
Ω
470 10 × 12.5 2.980 0.457 0.373 0.336
560 10 × 12.5 2.980 0.383 0.373 0.336
450
450
714
714
875
1105
1358
1358
1895
2279
2190
2454
2454
3178
3638
4244
630
B41866C4477M***
B41866C4567M***
B41866C4687M***
B41866C4827M***
B41866C4108M***
B41866C4128M***
B41866C4158M***
B41866C4188M***
B41866C4228M***
B41866C4278M***
B41866D4278M***
B41866C4338M***
B41866C4398M***
B41866C4478M***
B41866C4568M***
B41866C4688M***
630
1000
1000
1225
1546
1901
1901
2652
3190
3066
3435
3435
4450
5093
5941
680 10 × 16
820 10 × 16
1000 10 × 20
1200 12.5 × 20
1500 12.5 × 25
1800 12.5 × 25
2200 16 × 20
2700 16 × 25
2700 18 × 20
3300 18 × 25
3900 18 × 25
1.404 0.316 0.175 0.160
1.404 0.262 0.175 0.160
1.070 0.215 0.134 0.127
0.881 0.179 0.110 0.104
0.710 0.143 0.089 0.082
0.710 0.119 0.089 0.082
0.401 0.109 0.050 0.046
0.314 0.089 0.039 0.037
0.341 0.089 0.043 0.040
0.314 0.080 0.039 0.037
0.314 0.068 0.039 0.037
4700 18 × 31.5 0.226 0.062 0.028 0.027
5600 18 × 35
6800 18 × 40
0.187 0.056 0.023 0.022
0.153 0.050 0.019 0.018
VR = 25 V DC
100
120
150
180
220
8
8
8
8
8
× 11.5 5.170 2.147 0.646 0.573
× 11.5 5.170 1.789 0.646 0.573
× 11.5 5.170 1.432 0.646 0.573
× 11.5 5.170 1.193 0.646 0.573
× 11.5 5.170 0.976 0.646 0.573
297
297
297
297
297
450
450
714
714
875
875
1105
416
416
416
416
416
B41866C5107M***
B41866C5127M***
B41866C5157M***
B41866C5187M***
B41866C5227M***
B41866C5277M***
B41866C5337M***
B41866C5397M***
B41866C5477M***
B41866C5567M***
B41866C5687M***
B41866C5827M***
270 10 × 12.5 2.980 0.795 0.373 0.336
330 10 × 12.5 2.980 0.651 0.373 0.336
630
630
390 10 × 16
470 10 × 16
560 10 × 20
680 10 × 20
820 12.5 × 20
1.404 0.551 0.175 0.160
1.404 0.457 0.175 0.160
1.070 0.383 0.134 0.127
1.070 0.316 0.134 0.127
0.881 0.262 0.110 0.104
1000
1000
1225
1225
1546
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for ≥ 10 mm)
002 = for cut leads, bulk (for ≥ 10 mm)
003 = for crimped leads, blister (for ≥ 16 mm)
004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm)
012 = for bent 90° leads, blister (for 16 and 18 mm)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 8 of 30
B41866
High ripple current ꢀ 125 °C
Technical data and ordering codes
CR Case ESRmax ESRmax ESRmax Zmax
IAC,R
IAC,max
Ordering code
120 Hz dimensions 10 kHz 120 Hz 10 kHz 100 kHz 100 kHz 100 kHz (composition see
20 °C d × l ꢀ40 °C 20 °C 20 °C 20 °C 125 °C 105 °C below)
µF mm
Ω
Ω
Ω
Ω
mA
mA
VR = 25 V DC
1000 12.5 × 20
1200 12.5 × 25
1500 12.5 × 25
1800 16 × 20
2200 12.5 × 40
2200 16 × 25
2200 18 × 20
2700 16 × 31.5 0.249 0.089 0.031 0.029
3300 18 × 31.5 0.226 0.080 0.028 0.027
3900 18 × 35
4700 18 × 40
0.881 0.215 0.110 0.104
0.710 0.179 0.089 0.082
0.710 0.143 0.089 0.082
0.401 0.119 0.050 0.046
0.406 0.109 0.051 0.047
0.314 0.109 0.039 0.037
0.341 0.109 0.043 0.040
1105
1358
1358
1895
2185
2279
2190
2822
3178
3638
4244
1546
1901
1901
2652
3058
3190
3066
3950
4450
5093
5941
B41866C5108M***
B41866C5128M***
B41866C5158M***
B41866C5188M***
B41866C5228M***
B41866D5228M***
B41866E5228M***
B41866C5278M***
B41866C5338M***
B41866C5398M***
B41866C5478M***
0.187 0.068 0.023 0.022
0.153 0.062 0.019 0.018
VR = 35 V DC
100
120
8
8
× 11.5 5.170 1.516 0.646 0.573
× 11.5 5.170 1.263 0.646 0.573
297
297
450
450
450
714
714
875
875
1105
1105
1358
1895
2279
2279
2190
416
416
630
630
630
1000
1000
1225
1225
1546
1546
1901
2652
3190
3190
3066
B41866C7107M***
B41866C7127M***
B41866C7157M***
B41866C7187M***
B41866C7227M***
B41866C7277M***
B41866C7337M***
B41866C7397M***
B41866C7477M***
B41866C7567M***
B41866C7687M***
B41866C7827M***
B41866C7108M***
B41866C7128M***
B41866C7158M***
B41866D7158M***
150 10 × 12.5 2.980 1.011 0.373 0.336
180 10 × 12.5 2.980 0.842 0.373 0.336
220 10 × 12.5 2.980 0.689 0.373 0.336
270 10 × 16
330 10 × 16
390 10 × 20
470 10 × 20
560 12.5 × 20
680 12.5 × 20
820 12.5 × 25
1000 16 × 20
1200 16 × 25
1500 16 × 25
1500 18 × 20
1.404 0.561 0.175 0.160
1.404 0.459 0.175 0.160
1.070 0.389 0.134 0.127
1.070 0.323 0.134 0.127
0.881 0.271 0.110 0.104
0.881 0.223 0.110 0.104
0.710 0.185 0.089 0.082
0.401 0.152 0.050 0.046
0.314 0.126 0.039 0.037
0.314 0.101 0.039 0.037
0.341 0.101 0.043 0.040
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for ≥ 10 mm)
002 = for cut leads, bulk (for ≥ 10 mm)
003 = for crimped leads, blister (for ≥ 16 mm)
004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm)
012 = for bent 90° leads, blister (for 16 and 18 mm)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 9 of 30
B41866
High ripple current ꢀ 125 °C
Technical data and ordering codes
CR Case ESRmax ESRmax ESRmax Zmax
IAC,R
IAC,max
Ordering code
120 Hz dimensions 10 kHz 120 Hz 10 kHz 100 kHz 100 kHz 100 kHz (composition see
20 °C d × l ꢀ40 °C 20 °C 20 °C 20 °C 125 °C 105 °C below)
µF mm
VR = 35 V DC
1800 16 × 31.5 0.249 0.084 0.031 0.029
1800 18 × 25 0.314 0.084 0.039 0.037
2200 18 × 31.5 0.226 0.080 0.028 0.027
Ω
Ω
Ω
Ω
mA
mA
2822
2454
3178
3638
4244
3950
3435
4450
5093
5941
B41866C7188M***
B41866D7188M***
B41866C7228M***
B41866C7278M***
B41866C7338M***
2700 18 × 35
3300 18 × 40
0.187 0.065 0.023 0.022
0.153 0.061 0.019 0.018
VR = 50 V DC
10
12
15
18
22
27
33
39
47
56
68
82
8
8
8
8
8
8
8
8
8
8
8
8
× 11.5 7.445 12.631 0.931 0.826
× 11.5 7.445 10.526 0.931 0.826
× 11.5 7.445 8.421 0.931 0.826
× 11.5 7.445 7.017 0.931 0.826
× 11.5 7.445 5.742 0.931 0.826
× 11.5 7.445 4.678 0.931 0.826
× 11.5 6.204 3.828 0.776 0.688
× 11.5 6.204 3.239 0.776 0.688
× 11.5 5.687 2.688 0.711 0.631
× 11.5 5.429 2.256 0.679 0.602
× 11.5 5.170 1.858 0.646 0.573
× 11.5 5.170 1.540 0.646 0.573
160
160
160
160
210
210
250
250
370
370
370
370
450
714
714
875
875
875
1105
1358
1358
1895
1895
224
224
224
224
294
294
350
350
518
518
518
518
630
1000
1000
1225
1225
1225
1546
1901
1901
2652
2652
B41866C6106M***
B41866C6126M***
B41866C6156M***
B41866C6186M***
B41866C6226M***
B41866C6276M***
B41866C6336M***
B41866C6396M***
B41866C6476M***
B41866C6566M***
B41866C6686M***
B41866C6826M***
B41866C6107M***
B41866C6127M***
B41866C6157M***
B41866C6187M***
B41866C6227M***
B41866C6277M***
B41866C6337M***
B41866C6397M***
B41866C6477M***
B41866D6477M***
B41866C6567M***
100 10 × 12.5 2.980 1.263 0.373 0.336
120 10 × 16
150 10 × 16
180 10 × 20
220 10 × 20
270 10 × 20
330 12.5 × 20
390 12.5 × 25
470 12.5 × 25
470 16 × 20
560 16 × 20
1.404 1.053 0.175 0.160
1.404 0.842 0.175 0.160
1.070 0.702 0.134 0.127
1.070 0.574 0.134 0.127
1.070 0.468 0.134 0.127
0.881 0.383 0.110 0.104
0.710 0.324 0.089 0.082
0.710 0.269 0.089 0.082
0.401 0.269 0.050 0.046
0.401 0.226 0.050 0.046
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for ≥ 10 mm)
002 = for cut leads, bulk (for ≥ 10 mm)
003 = for crimped leads, blister (for ≥ 16 mm)
004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm)
012 = for bent 90° leads, blister (for 16 and 18 mm)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 10 of 30
B41866
High ripple current ꢀ 125 °C
Technical data and ordering codes
CR Case ESRmax ESRmax ESRmax Zmax
IAC,R
IAC,max
Ordering code
120 Hz dimensions 10 kHz 120 Hz 10 kHz 100 kHz 100 kHz 100 kHz (composition see
20 °C d × l ꢀ40 °C 20 °C 20 °C 20 °C 125 °C 105 °C below)
µF mm
Ω
Ω
Ω
Ω
mA
mA
VR = 50 V DC
680 16 × 25
820 16 × 25
820 18 × 20
1000 16 × 31.5 0.249 0.126 0.031 0.029
1000 18 × 25 0.314 0.126 0.039 0.037
1200 18 × 31.5 0.226 0.105 0.028 0.027
0.314 0.186 0.039 0.037
0.314 0.154 0.039 0.037
0.153 0.154 0.019 0.018
2279
2279
3265
2822
2454
3178
3638
4244
3190
3190
4571
3950
3435
4450
5093
5941
B41866C6687M***
B41866C6827M***
B41866D6827M***
B41866C6108M***
B41866D6108M***
B41866C6128M***
B41866C6158M***
B41866C6188M***
1500 18 × 35
1800 18 × 40
0.187 0.084 0.023 0.022
0.153 0.070 0.019 0.018
VR = 63 V DC
33
8
× 11.5 24.600 5.742 2.460 2.160
153
309
309
309
433
433
433
433
433
546
723
723
723
989
930
930
1588
1165
1052
214
433
433
433
606
606
606
606
606
B41866C8336M***
B41866C8396M***
B41866C8476M***
B41866C8566M***
B41866C8686M***
B41866C8826M***
B41866C8107M***
B41866C8127M***
B41866C8157M***
B41866C8187M***
B41866C8227M***
B41866C8277M***
B41866C8337M***
B41866C8397M***
B41866C8477M***
B41866C8567M***
B41866C8687M***
B41866D8687M***
B41866E8687M***
39 10 × 12.5 7.963 4.858 0.796 0.711
47 10 × 12.5 7.963 4.031 0.796 0.711
56 10 × 12.5 7.963 3.383 0.796 0.711
68 10 × 16
82 10 × 16
100 10 × 16
120 10 × 16
150 10 × 16
180 10 × 20
220 12.5 × 20
270 12.5 × 20
330 12.5 × 20
390 12.5 × 25
470 16 × 20
560 16 × 20
680 12.5 × 40
680 16 × 25
680 18 × 20
5.097 2.786 0.510 0.435
5.097 2.311 0.510 0.435
5.097 1.895 0.510 0.435
5.097 1.579 0.510 0.435
5.097 1.263 0.510 0.435
3.434 1.053 0.343 0.325
2.522 0.861 0.252 0.243
2.522 0.702 0.252 0.243
2.522 0.574 0.252 0.243
1.671 0.486 0.167 0.155
2.030 0.403 0.203 0.191
2.030 0.338 0.203 0.191
0.948 0.279 0.095 0.089
1.522 0.279 0.152 0.143
1.845 0.279 0.185 0.173
765
1012
1012
1012
1385
1301
1301
2223
1631
1473
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for ≥ 10 mm)
002 = for cut leads, bulk (for ≥ 10 mm)
003 = for crimped leads, blister (for ≥ 16 mm)
004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm)
012 = for bent 90° leads, blister (for 16 and 18 mm)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 11 of 30
B41866
High ripple current ꢀ 125 °C
Technical data and ordering codes
CR Case ESRmax ESRmax ESRmax Zmax
IAC,R
IAC,max
Ordering code
120 Hz dimensions 10 kHz 120 Hz 10 kHz 100 kHz 100 kHz 100 kHz (composition see
20 °C d × l ꢀ40 °C 20 °C 20 °C 20 °C 125 °C 105 °C below)
µF mm
VR = 63 V DC
Ω
Ω
Ω
Ω
mA
mA
820 16 × 31.5 1.219 0.231 0.122 0.109
1000 16 × 31.5 1.219 0.189 0.122 0.109
1200 18 × 31.5 1.108 0.158 0.111 0.099
1461
1461
1645
1847
2015
2045
2045
2303
2586
2611
B41866C8827M***
B41866C8108M***
B41866C8128M***
B41866C8158M***
B41866C8188M***
1500 18 × 35
1800 18 × 40
0.936 0.126 0.094 0.085
0.840 0.105 0.084 0.080
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for ≥ 10 mm)
002 = for cut leads, bulk (for ≥ 10 mm)
003 = for crimped leads, blister (for ≥ 16 mm)
004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm)
012 = for bent 90° leads, blister (for 16 and 18 mm)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 12 of 30
B41866
High ripple current ꢀ 125 °C
Useful life
depending on ambient temperature TA under ripple current operating conditions1)
d = 8 mm and 10 mm
d ≥ 12 mm
1) Refer to chapter "General technical information, 5.3 Calculation of useful life" for an explanation on how to interpret the useful life
graphs.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 13 of 30
B41866
High ripple current ꢀ 125 °C
Frequency factor of permissible ripple current IAC versus frequency f
Please read Cautions and warnings and
Important notes at the end of this document.
Page 14 of 30
B41866
High ripple current ꢀ 125 °C
Taping, packing and lead configurations
Taping
Single-ended capacitors are available taped in Ammo pack from diameter 5 to 18 mm as follows:
Lead spacing F = 2.5 mm ( d = 5 … 6.3 mm)
Lead spacing F = 3.5 mm ( d = 8 mm)
Lead spacing F = 5.0 mm ( d = 5 … 12.5 mm)
Lead spacing F = 7.5 mm ( d = 16 ... 18 mm).
Lead spacing 2.5 mm ( d = 5 ... 6.3 mm)
Last 3 digits of ordering code: 007
Dimensions in mm
d
F
H
W
W0
W1
W2
H0
P
P0
P1
I1
t
∆h
D0
5
2.5 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 5.1 1.0 0.7 1.0 4.0
6.3
Toler-
ance
+0.8
±0.75 ±0.5 min. ±0.5 max. ±0.5 ±1.0 ±0.2 ±0.5 max. ±0.2 max. ±0.2
ꢀ02
Please read Cautions and warnings and
Important notes at the end of this document.
Page 15 of 30
B41866
High ripple current ꢀ 125 °C
Lead spacing 3.5 mm ( d = 8 mm)
Last 3 digits of ordering code: 006
Dimensions in mm
d
F
H
W
W0
W1
W2
1.5
P
P0
P1
I1
t
∆h
D0
8
3.5
18.5 18.0 12.5 9.0
12.7 12.7 4.6
1.0
0.7
1.0
4.0
Toler-
ance
+0.8
ꢀ02
1.0
±0.5 min. ±0.5 max. ±1.0 ±0.2 ±0.5 max. ±0.2 max. ±0.2
Please read Cautions and warnings and
Important notes at the end of this document.
Page 16 of 30
B41866
High ripple current ꢀ 125 °C
Lead spacing 5.0 mm ( d = 5 ... 8 mm)
Last 3 digits of ordering code: 008
Lead spacing 5.0 mm ( d = 10 ... 12.5 mm)
Last 3 digits of ordering code: 008
Dimensions in mm
d
F
H
W
W0 W1 W2
H0
P
P0
P1
I1
t
∆h
D0
5
5.0
18.5 18.0 5.5 9.0 1.5
16.0 12.7 12.7 3.85 1.0
0.7 1.0
4.0
6.3
8
20.0
16.0 12.7 12.7 3.85
10
5.0
19.0 18.0 12.5 9.0 1.5
19.0
ꢀ
ꢀ
12.7 12.7 3.85 1.0
15.0 15.0 5.0
0.7 1.0
4.0
12.5
Toler-
ance
+0.8
ꢀ02
±0.75 ±0.5 min. ±0.5 max. ±0.5 ±1.0 ±0.2 ±0.5 max. ±0.2 max. ±0.2
Please read Cautions and warnings and
Important notes at the end of this document.
Page 17 of 30
B41866
High ripple current ꢀ 125 °C
Lead spacing 7.5 mm ( d = 16 ...18 mm)
Last 3 digits of ordering code: 009
Dimensions in mm
d
F
H
W
W0
W1
W2
1.5
P
P0
P1
I1
t
∆P ∆h D0
4.0
16
18 *)
7.5 18.5 18.0 12.5 9.0
30.0 15.0 3.75 1.0
0.7
0
0
Toler-
ance
ꢀ0.5
+0.75
±0.8
±0.5 min. ±0.5 max. ±1.0 ±0.2 ±0.5 max. ±0.2 ±1.0 ±1.0 ±0.2
*) Available only for case dimensions 18 × 20, 18 × 25 and 18 × 31.5 mm
Please read Cautions and warnings and
Important notes at the end of this document.
Page 18 of 30
B41866
High ripple current ꢀ 125 °C
Packing units and box dimensions
Ammo pack
Case size
d × l
Dimensions (mm)
Packing
units
mm
Amax
345
345
345
345
345
345
345
345
345
345
315
315
315
315
315
315
Bmax
55
55
55
55
60
60
65
65
65
65
65
65
65
65
65
65
Cmax
240
290
240
280
200
200
280
280
280
275
275
275
275
275
275
275
pcs.
5 × 11
2000
2000
1000
750
500
500
500
500
500
500
300
300
300
250
250
250
6.3 × 11
8 × 11.5
10 × 12.5
10 × 16
10 × 20
12.5 × 20
12.5 × 25
12.5 × 25
12.5 × 30
16 × 20
16 × 25
16 × 31.5
18 × 20
18 × 25
18 × 31.5
Please read Cautions and warnings and
Important notes at the end of this document.
Page 19 of 30
B41866
High ripple current ꢀ 125 °C
Kinked or cut leads
Single-ended capacitors are available with kinked or cut leads. Other lead configurations also
available upon request.
Kinked leads
Last 3 digits of ordering code: 001
With stand-off rubber seal
Case size
d × l (mm)
10 × 20
Dimensions (mm)
a ±0.5
5.0
12.5 × 20
12.5 × 25
12.5 × 30
12.5 × 35
12.5 × 40
16 × 20
5.0
5.0
5.0
5.0
5.0
7.5
16 × 25
7.5
16 × 31.5
18 × 20
7.5
7.5
18 × 25
7.5
18 × 31.5
18 × 35
7.5
With flat rubber seal
7.5
18 × 40
7.5
20 × 20
10.0
10.0
10.0
10.0
10.0
10.0
20 × 25
20 × 40
22 × 30
22 × 35
22 × 40
Please read Cautions and warnings and
Important notes at the end of this document.
Page 20 of 30
B41866
High ripple current ꢀ 125 °C
Cut leads
Last 3 digits of ordering code: 002
With stand-off rubber seal
Case size
d × l (mm)
10 × 12.5
10 × 16
Dimensions (mm)
a ±0.5
5.0
5.0
10 × 20
5.0
12.5 × 20
12.5 × 25
12.5 × 30
12.5 × 35
12.5 × 40
16 × 20
5.0
5.0
5.0
With flat rubber seal
5.0
5.0
7.5
16 × 25
7.5
16 × 31.5
18 × 20
7.5
7.5
18 × 25
7.5
18 × 31.5
18 × 35
7.5
7.5
18 × 40
7.5
20 × 20
10.0
10.0
10.0
20 × 25
20 × 40
Please read Cautions and warnings and
Important notes at the end of this document.
Page 21 of 30
B41866
High ripple current ꢀ 125 °C
PAPR leads (Protection Against Polarity Reversal)
These lead configurations ensure correct placement of the capacitor on the PCB with regard to
polarity. PAPR leads are available for diameters from 10 mm up to 20 mm.
There are three configurations available: Crimped leads, J leads, bent 90° leads
Crimped leads
Last 3 digits of ordering code: 003
With stand-off rubber seal
With flat rubber seal
Suggestion for PCB hole diameter
Case size
d × l (mm)
16 × 20
16 × 25
16 × 31.5
18 × 20
18 × 25
18 × 31.5
18 × 35
18 × 40
20 × 20
20 × 25
20 × 40
Dimensions (mm)
B ±0.2
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
C ±0.5
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
D ±0.1
E ±0.1
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
a ±0.5
b
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.3
1.6
1.6
1.6
7.5
7.5
0.8 ±0.05
0.8 ±0.05
0.8 ±0.05
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
1.0 ±0.1
1.0 ±0.1
1.0 ±0.1
7.5
7.5
7.5
7.5
7.5
7.5
10.0
10.0
10.0
Please read Cautions and warnings and
Important notes at the end of this document.
Page 22 of 30
B41866
High ripple current ꢀ 125 °C
J leads
Last 3 digits of ordering code: 004
Suggestion for PCB hole diameter
Case size
d × l (mm)
10 × 12.5
10 × 16
Dimensions (mm)
C ±0.5
3.2
3.2
3.2
3.2
3.2
3.5
3.5
3.5
3.5
3.5
3.5
3.5
E ±0.5
J ±0.2
1.2
1.2
1.2
1.2
1.2
1.6
1.6
1.6
1.6
1.6
1.6
1.6
a ±0.5
5.0
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
7.5
7.5
b
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.6 ±0.05
0.6 ±0.05
0.6 ±0.05
0.6 ±0.05
0.6 ±0.05
0.8 ±0.05
0.8 ±0.05
0.8 ±0.05
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
10 × 20
12.5 × 20
12.5 × 25
16 × 20
16 × 25
16 × 31.5
18 × 20
18 × 25
18 × 31.5
18 × 35
Please read Cautions and warnings and
Important notes at the end of this document.
Page 23 of 30
B41866
High ripple current ꢀ 125 °C
Bent 90° leads for horizontal mounting pinning
Last 3 digits of ordering code: 012
Case size
d × l (mm)
16 × 20
Dimensions (mm)
C ±0.5
4.0
E ±0.5
F ±0.5
12.0
12.0
12.0
13.0
13.0
13.0
13.0
13.0
a ±0.5
7.5
b
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
0.8 ±0.05
0.8 ±0.05
0.8 ±0.05
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
16 × 25
4.0
7.5
16 × 31.5
18 × 20
4.0
7.5
4.0
7.5
18 × 25
4.0
7.5
18 × 31.5
18 × 35
4.0
7.5
4.0
7.5
18 × 40
4.0
7.5
Bent leads for diameter 12.5 mm available upon request.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 24 of 30
B41866
High ripple current ꢀ 125 °C
Overview of packing units and code numbers for case sizes 5 × 11 ... 16 × 31.5
PAPR
Case size
d × l
Stan- Taped,
dard, Ammo pack
bulk
Kinked Cut
Crimped J leads Bent 90°
leads,
bulk
leads, leads
leads,
blister
bulk
pcs.
ꢀ
mm
pcs.
pcs.
pcs.
pcs.
ꢀ
pcs.
ꢀ
pcs.
5 × 11
2000 2000
2500 2000
1000 1000
1000 750
ꢀ
6.3 × 11
8 × 11.5
10 × 12.5
10 × 16
10 × 20
12.5 × 20
12.5 × 25
12.5 × 30
12.5 × 35
12.5 × 40
16 × 20
16 × 25
16 × 31.5
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
1000
1000
500
350
500
175
175
175
200
200
250
002
ꢀ
675
675
500
300
225
180
150
150
200
200
344
004
100
500
350
250
200
175
175
250
250
200
500
ꢀ
ꢀ
500
500
350
500
175
175
175
200
200
250
001
ꢀ
1)
1)
1)
1)
1)
500
ꢀ
500
ꢀ
500
ꢀ
-
ꢀ
-
ꢀ
300
200
200
344
003
120
120
120
012
300
300
The last three 000
digits of the
complete
ordering code
state the lead
configuration
Code F (mm) d (mm)
006
007
008
009
3.5
2.5
5
8
5...6.3
5...12.5
16...18
7.5
1) Available upon request
Please read Cautions and warnings and
Important notes at the end of this document.
Page 25 of 30
B41866
High ripple current ꢀ 125 °C
Overview of packing units and code numbers for case sizes 18 × 20 ... 25 × 40
PAPR
Case size
d × l
Stan- Taped,
dard, Ammo pack
bulk
Kinked Cut
Crimped J leads Bent 90°
leads,
bulk
leads, leads
leads,
blister
bulk
pcs.
175
150
100
100
100
125
125
100
100
100
100
100
100
ꢀ
mm
pcs.
175
150
100
100
125
125
125
100
100
100
80
pcs.
pcs.
175
150
100
100
100
125
125
100
100
100
100
100
100
100
001
pcs.
200
200
150
150
120
200
200
120
120
120
ꢀ
pcs.
200
200
150
150
ꢀ
pcs.
120
120
120
150
72
ꢀ
18 × 20
18 × 25
18 × 31.5
18 × 35
18 × 40
20 × 20
20 × 25
20 × 30
20 × 35
20 × 40
22 × 30
22 × 35
22 × 40
25 × 40
250
250
250
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
80
ꢀ
ꢀ
ꢀ
ꢀ
80
ꢀ
ꢀ
ꢀ
ꢀ
40
ꢀ
ꢀ
ꢀ
ꢀ
The last three 000
digits of the
complete
ordering code
state the lead
configuration
Code F (mm) d (mm)
002
003
004
012
007
008
009
2.5
5
7.5
4...6.3
6.3...12.5
16...18
Please read Cautions and warnings and
Important notes at the end of this document.
Page 26 of 30
B41866
High ripple current ꢀ 125 °C
Cautions and warnings
Personal safety
The electrolytes used by EPCOS have not only been optimized with a view to the intended
application, but also with regard to health and environmental compatibility. They do not contain
any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide
(DMAC).
Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They
contain flame-retarding substances which will quickly extinguish any flame that may have been
ignited.
As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce
operating electrolytes. However, in exceptional cases, such materials must be used in order to
achieve specific physical and electrical properties because no safe substitute materials are
currently known. However, the amount of dangerous materials used in our products has been
limited to an absolute minimum. Nevertheless, the following rules should be observed when
handling Al electrolytic capacitors:
Any escaping electrolyte should not come into contact with eyes or skin.
If electrolyte does come into contact with the skin, wash the affected parts immediately with
running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If
symptoms persist, seek medical treatment.
Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be
well ventilated. Clothing that has been contaminated by electrolyte must be changed and
rinsed in water.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 27 of 30
B41866
High ripple current ꢀ 125 °C
Product safety
The table below summarize the safety instructions that must be observed without fail. A detailed
description can be found in the relevant sections of chapter "General technical information".
Topic
Safety information
Reference
Chapter "General
technical information"
Polarity
Make sure that polar capacitors are connected
with the right polarity.
1
"Basic construction of
aluminum electrolytic
capacitors"
Reverse voltage
Voltages polarity classes should be prevented by 3.1.6
connecting a diode.
"Reverse voltage"
Upper category
temperature
Do not exceed the upper category temperatur.
7.2
"Maximum permissible
operating temperature"
Maintenance
Make periodic inspections of the capacitors.
10
Before the inspection, make sure that the power "Maintenance"
supply is turned off and carefully discharge the
electricity of the capacitors.
Do not apply any mechanical stress to the
capacitor terminals.
Mounting
position of screw
terminal capacitors
Do not mount the capacitor with the terminals
(safety vent) upside down.
11.1.
"Mounting positions of
capacitors with screw
terminals"
Mounting of
single-ended
capacitors
The internal structure of single-ended capacitors 11.4
might be damaged if excessive force is applied to "Mounting
the lead wires.
considerations for
Avoid any compressive, tensile or flexural stress. single-ended capacitors"
Do not move the capacitor after soldering to PC
board.
Do not pick up the PC board by the soldered
capacitor.
Do not insert the capacitor on the PC board with a
hole space different to the lead space specified.
Robustness of
terminals
The following maximum tightening torques must
not be exceeded when connecting screw
11.3
"Mounting torques"
terminals:
M5: 2 Nm
M6: 2.5 Nm
Soldering
Do not exceed the specified time or temperature 11.5
limits during soldering. "Soldering"
Please read Cautions and warnings and
Important notes at the end of this document.
Page 28 of 30
B41866
High ripple current ꢀ 125 °C
Topic
Safety information
Reference
Chapter "General
technical information"
Soldering,
Do not allow halogenated hydrocarbons to come 11.6
cleaning agents
into contact with aluminum electrolytic capacitors. "Cleaning agents"
Passive
Avoid external energy, such as fire or electricity.
8.1
flammability
"Passive flammability"
Active
Avoid overload of the capacitors.
8.2
flammability
"Active flammability"
Reference
Chapter "Capacitors
with screw terminals"
Breakdown strength Do not damage the insulating sleeve, especially
"Screw terminals -
accessories"
of insulating
sleeves
when ring clips are used for mounting.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 29 of 30
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical re-
quirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incum-
bent on the customer to check and decide whether an EPCOS product with the properties de-
scribed in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of passive electronic compon-
ents or failure before the end of their usual service life cannot be completely ruled out
in the current state of the art, even if they are operated as specified. In customer applica-
tions requiring a very high level of operational safety and especially in customer applications
in which the malfunction or failure of a passive electronic component could endanger human
life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured
by means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of a passive electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as “hazardous”). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver-
sion of the “General Terms of Delivery for Products and Services in the Electrical In-
dustry” published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, EPCOS-JONES, BAOKE, Alu-X, CeraDiode, CSSP, MLSC,
PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMID, SIOV, SIP5D, SIP5K,
UltraCap, WindCap are trademarks registered or pending in Europe and in other countries.
Further information will be found on the Internet at www.epcos.com/trademarks.
Page 30 of 30
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明