B57875S0212J000 [EPCOS]
NTC thermistors for temperature measurement; NTC热敏电阻温度测量
| 型号： | B57875S0212J000 |
| 厂家： | 
EPCOS |
| 描述： | NTC thermistors for temperature measurement |
| 文件： | 总19页 (文件大小：330K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
NTC thermistors for
temperature measurement
Leaded NTC thermistors,
lead spacing 5 mm
Series/Type:
B57875S
Date:
February 2009
© EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Temperature measurement
B57875S
S875
Leaded NTC thermistors, lead spacing 5 mm
Applications
Dimensional drawing
Temperature measurement
Features
High measuring accuracy
Cost-effective
Rugged design, epoxy resin encapsulation
Tinned copper leads
Lead spacing 5 mm
Options
Flexible coating of head and wires available
on request
Delivery mode
Bulk (standard), cardboard tape, reeled or in
Ammo pack on request
Dimensions in mm
Approx. weight 120 mg
General technical data
Climatic category
Max. power
(IEC 60068-1)
(at 25 °C)
55/155/56
60
∆RR/RR ±1, ±3, ±5
P25
mW
%
°C
mW/K
s
mJ/K
Resistance tolerance
Rated temperature
Dissipation factor
Thermal cooling time constant
Heat capacity
TR
δth
τc
25
(in air)
(in air)
approx. 3.8
approx. 7.5
approx. 28.5
Cth
Electrical specification and ordering codes
R25
No. of R/T
B25/100
Ordering code
Ω
characteristic
K
2.1 k
1008
8016
2908
2901
8018
3560 ±1%
3988 ±1%
3460 ±1%
3760 ±1%
3964 ±1%
B57875S0212+000
B57875S0103+001
B57875S0103+002
B57875S0123+000
B57875S0303+000
10 k
10 k
12 k
30 k
+ = Resistance tolerance
F = ±1%
H = ±3%
J = ±5%
Please read Cautions and warnings and
Important notes at the end of this document.
Page 2 of 19
Temperature measurement
B57875S
S875
Leaded NTC thermistors, lead spacing 5 mm
Reliability data
Test
Standard
Test conditions
∆R25/R25
Remarks
(typical)
Storage in
dry heat
IEC
60068-2-2
Storage at upper
category temperature
T: 155 °C
< 2%
No visible
damage
t: 1000 h
Storage in damp
heat, steady state
IEC
Temperature of air: 40 °C
< 1%
No visible
damage
60068-2-78 Relative humidity of air: 93%
Duration: 56 days
Rapid temperature IEC
Lower test temperature: ꢀ55 °C < 2%
No visible
damage
cycling
60068-2-14 Upper test temperature: 155 °C
Number of cycles: 100
Endurance
Pmax: 60 mW
t: 1000 h
< 3%
< 3%
No visible
damage
Long-term stability
(empirical value)
Temperature: 70 °C
t: 10000 h
No visible
damage
Please read Cautions and warnings and
Important notes at the end of this document.
Page 3 of 19
Temperature measurement
B57875S
S875
Leaded NTC thermistors, lead spacing 5 mm
R/T characteristics
1008
2901
2908
R/T No.
T (°C)
B25/100 = 3560 K
RT/R25
B25/100 = 3760 K
B25/100 = 3460 K
α (%/K) RT/R25
α (%/K) RT/R25
α (%/K)
ꢀ55.0 53.104
ꢀ50.0 39.318
ꢀ45.0 29.325
ꢀ40.0 22.03
ꢀ35.0 16.666
6.1
6.0
5.8
5.7
5.5
63.969
46.179
33.738
24.927
18.611
6.7
6.4
6.2
6.0
5.8
45.313
33.729
25.333
19.191
14.659
6.0
5.8
5.6
5.5
5.3
ꢀ30.0 12.696
5.4
5.2
5.1
4.9
4.8
14.033
10.679
8.198
6.3123
4.9014
5.6
5.4
5.3
5.2
5.1
11.288
8.7588
6.8471
5.391
5.1
5.0
4.9
4.7
4.6
ꢀ25.0
ꢀ20.0
ꢀ15.0
ꢀ10.0
9.7251
7.5171
5.8353
4.5686
4.2739
ꢀ5.0
0.0
5.0
10.0
15.0
3.605
4.7
4.5
4.4
4.3
4.1
3.821
3.0027
2.3801
1.9
4.9
4.7
4.6
4.5
4.3
3.4109
2.7396
2.214
1.7999
1.4716
4.4
4.3
4.2
4.1
4.0
2.8665
2.2907
1.8438
1.492
1.5257
20.0
25.0
30.0
35.0
40.0
1.2154
1.0000
0.82976
0.68635
0.57103
4.0
3.9
3.8
3.7
3.6
1.233
4.3
4.1
4.0
3.9
3.8
1.2099
1.0000
0.83078
0.69361
0.58186
3.9
3.8
3.7
3.6
3.5
1.0000
0.81679
0.67166
0.55527
45.0
50.0
55.0
60.0
65.0
0.48015
0.40545
0.3417
0.28952
0.24714
3.5
3.4
3.3
3.2
3.1
0.46095
0.38459
0.32184
0.27068
0.22907
3.8
3.7
3.6
3.5
3.3
0.49036
0.41509
0.35288
0.30124
0.25818
3.4
3.3
3.2
3.1
3.0
70.0
75.0
80.0
85.0
90.0
0.21183
0.18194
0.1568
0.13592
0.11822
3.1
3.0
2.9
2.8
2.8
0.19468
0.16607
0.14221
0.12218
0.10533
3.2
3.1
3.1
3.0
2.9
0.22213
0.19183
0.16626
0.1446
3.0
2.9
2.8
2.8
2.7
0.12618
95.0
100.0
105.0
110.0
115.0
0.1034
2.7
2.6
2.6
2.5
2.4
0.09123
0.079284
0.069062
0.06034
0.052886
2.8
2.8
2.7
2.7
2.6
0.11047
2.6
2.6
2.5
2.4
2.4
0.090741
0.079642
0.070102
0.061889
0.097017
0.085463
0.075506
0.066899
120.0
125.0
130.0
135.0
140.0
0.054785
0.048706
0.043415
0.038722
0.034615
2.4
2.3
2.3
2.2
2.2
0.046482
0.040985
0.036233
0.032101
0.02851
2.5
2.5
2.5
2.4
2.4
0.059437
0.052948
0.047289
0.042341
0.038003
2.3
2.3
2.2
2.2
2.1
145.0
150.0
155.0
0.031048
0.02791
0.025193
2.1
2.1
2.0
0.025373
0.022633
0.020231
2.3
2.3
2.3
0.034189
0.030828
0.027859
2.1
2.0
2.0
Please read Cautions and warnings and
Important notes at the end of this document.
Page 4 of 19
Temperature measurement
B57875S
S875
Leaded NTC thermistors, lead spacing 5 mm
1008
2901
2908
R/T No.
T (°C)
B25/100 = 3560 K
RT/R25
B25/100 = 3760 K
B25/100 = 3460 K
α (%/K) RT/R25
α (%/K) RT/R25
α (%/K)
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
160.0
165.0
0.02279
0.020667
2.0
2.0
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
170.0
175.0
180.0
185.0
190.0
0.01878
0.01709
0.015582
0.014227
0.013012
1.9
1.9
1.8
1.8
1.8
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
195.0
200.0
205.0
210.0
215.0
0.011934
0.010964
0.0101
0.0093191
0.0085949
1.7
1.7
1.7
1.6
1.6
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
220.0
225.0
230.0
235.0
240.0
0.0079384
0.0073411
0.006798
0.0063087
0.0058623
1.6
1.5
1.5
1.5
1.5
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
245.0
250.0
0.0054487
0.0050705
1.4
1.4
Please read Cautions and warnings and
Important notes at the end of this document.
Page 5 of 19
Temperature measurement
B57875S
S875
Leaded NTC thermistors, lead spacing 5 mm
R/T characteristics
8016
8018
R/T No.
T (°C)
B25/100 = 3988 K
RT/R25
B25/100 = 3964 K
α (%/K) RT/R25
α (%/K)
ꢀ55.0 96.3
ꢀ50.0 67.01
ꢀ45.0 47.17
ꢀ40.0 33.65
ꢀ35.0 24.26
7.4
7.2
6.9
6.7
6.4
ꢀ
ꢀ
ꢀ
30.24
22.1
ꢀ
ꢀ
ꢀ
6.3
6.1
ꢀ30.0 17.7
ꢀ25.0 13.04
6.2
6.0
5.8
5.6
5.5
16.32
12.17
9.153
6.945
5.313
5.9
5.8
5.6
5.4
5.2
ꢀ20.0
ꢀ15.0
ꢀ10.0
9.707
7.293
5.533
ꢀ5.0
0.0
5.0
10.0
15.0
4.232
3.265
2.539
1.99
5.3
5.1
5.0
4.8
4.7
4.097
3.183
2.491
1.963
1.557
5.1
4.9
4.8
4.7
4.6
1.571
20.0
25.0
30.0
35.0
40.0
1.249
4.5
4.4
4.3
4.1
4.0
1.244
4.4
4.3
4.2
4.1
4.0
1.0000
0.8057
0.6531
0.5327
1.0000
0.8083
0.6572
0.5373
45.0
50.0
55.0
60.0
65.0
0.4369
0.3603
0.2986
0.2488
0.2083
3.9
3.8
3.7
3.6
3.5
0.4418
0.365
0.303
0.2527
0.2118
3.9
3.7
3.7
3.6
3.5
70.0
75.0
80.0
85.0
90.0
0.1752
0.1481
0.1258
0.1072
0.09177
3.4
3.3
3.2
3.2
3.1
0.1783
0.1508
0.128
0.1091
0.0933
3.4
3.3
3.2
3.2
3.1
95.0
100.0
105.0
110.0
115.0
0.07885
0.068
0.05886
0.05112
0.04454
3.0
2.9
2.9
2.8
2.7
0.08016
0.0691
0.05974
0.05183
0.04512
3.0
2.9
2.9
2.8
2.8
120.0
125.0
130.0
135.0
140.0
0.03893
0.03417
0.03009
0.02654
0.02348
2.6
2.6
2.5
2.5
2.4
0.0394
0.0345
0.03032
0.02672
0.02361
2.7
2.6
2.6
2.5
2.5
145.0
150.0
155.0
0.02083
0.01853
0.01653
2.4
2.3
2.3
0.02091
0.01857
0.016537
2.4
2.4
2.3
Please read Cautions and warnings and
Important notes at the end of this document.
Page 6 of 19
Temperature measurement
B57875S
S875
Leaded NTC thermistors, lead spacing 5 mm
Please read Cautions and warnings and
Important notes at the end of this document.
Page 7 of 19
Temperature measurement
B57875S
S875
Leaded NTC thermistors, lead spacing 5 mm
Taping and packing
1
Taping of radial leaded NTC thermistors
Dimensions and tolerances
Lead spacing F = 2.5 mm and 5.0 mm (taping to IEC 60286-2)
Dimensions (mm)
Lead
spacing
2.5 mm
11.0
5.0
Lead
spacing
5 mm
11.5
6.0
Tolerance of
lead spacing
2.5/5 mm
max.
Remarks
b
s
max.
d
0.5/0.6
12.7
5.1
2.5
0
0
18.0
5.5
9.0
3.0
0.5/0.6
12.7
3.85
5.0
0
0
18.0
5.5
9.0
±0.05
±0.3
±0.7
+0.6/ꢀ0.1
±2.0
±1.3
±0.5
min.
+0.75/ꢀ0.5
max.
+2.0/ꢀ0
±0.5
P0
P1
F
∆h
∆p
W
W0
W1
W2
H
±1 mm / 20 sprocket holes
measured at top of component body
peel-off force ≥5 N
3.0
18.0
16.0
32.2
4.0
18.0
16.0
32.2
4.0
H0
H1
D0
t
max.
±0.2
max.
0.9
0.9
without wires
L
L1
11.0
4.0
11.0
4.0
max.
max.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 8 of 19
Temperature measurement
B57875S
S875
Leaded NTC thermistors, lead spacing 5 mm
Types of packing
Ammo packing
Ammo
type
x
y
z
I
80
240
210
Packing unit: 1000 - 2000 pcs./reel
Reel packing
Packing unit: 1000 - 2000 pcs./reel
Reel dimensions (in mm)
Reel type
d
f
n
w
I
360 max.
500 max.
31 ±1
23 ±1
approx. 45
approx. 59
54 max.
72 max.
II
Please read Cautions and warnings and
Important notes at the end of this document.
Page 9 of 19
Temperature measurement
B57875S
S875
Leaded NTC thermistors, lead spacing 5 mm
Cassette packing
Packing unit: 1000 - 2000 pcs./cassette
Bulk packing
The components are packed in cardboard boxes, the size of which depends on the order quantity.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 10 of 19
Temperature measurement
B57875S
S875
Leaded NTC thermistors, lead spacing 5 mm
2
Packing codes
The last two digits of the complete ordering code state the packing mode:
Last two digits
00, 01, 02, 03,04,
05, 06, 07, 08
ꢀ
Bulk
ꢀ
40
45
50
51
52
53
54
55
60
62
70
72
ꢀ
Bulk
ꢀ
ꢀ
Bulk
ꢀ
Radial leads, kinked
Radial leads, kinked
Cardboard tape
Cardboard tape
Cassette packing
360 or 500-mm reel packing
Cassette packing
Radial leads, straight Cardboard tape
Radial leads, straight Cardboard tape
360 or 500-mm reel packing
AMMO packing
Radial leads, kinked
Cardboard tape
Radial leads, straight Cardboard tape
AMMO packing
SMD
SMD
SMD
SMD
Cardboard tape
Blister tape
180-mm reel packing
180-mm reel packing
330-mm reel packing
330-mm reel packing
Cardboard tape
Blister tape
(If no packing code is indicated, this corresponds to 40)
Example 1: B57164K0102J000
B57164K0102J052
Bulk
Cardboard tape, cassette packing
Example 2: B57881S0103F002
B57881S0103F251
Bulk
Cardboard tape, reel packing
Please read Cautions and warnings and
Important notes at the end of this document.
Page 11 of 19
Temperature measurement
B57875S
S875
Leaded NTC thermistors, lead spacing 5 mm
Mounting instructions
1
Soldering
1.1
Leaded NTC thermistors
Leaded thermistors comply with the solderability requirements specified by CECC.
When soldering, care must be taken that the NTC thermistors are not damaged by excessive
heat. The following maximum temperatures, maximum time spans and minimum distances have
to be observed:
Dip soldering
max. 260 °C
max. 4 s
Iron soldering
max. 360 °C
max. 2 s
Bath temperature
Soldering time
Distance from thermistor
min. 6 mm
min. 6 mm
Under more severe soldering conditions the resistance may change.
1.2 Leadless NTC thermistors
In case of NTC thermistors without leads, soldering is restricted to devices which are provided
with a solderable metallization. The temperature shock caused by the application of hot solder
may produce fine cracks in the ceramic, resulting in changes in resistance.
To prevent leaching of the metallization, solder with silver additives or with a low tin content
should be used. In addition, soldering methods should be employed which permit short soldering
times.
2
Clamp contacting
Pressure contacting by means of clamps is particularly suitable for applications involving frequent
switching and high turn-on powers.
3
Robustness of terminations (leaded types)
The leads meet the requirements of IEC 60068-2-21. They may not be bent closer than 4 mm
from the solder joint on the thermistor body or from the point at which they leave the feed-
throughs. During bending, any mechanical stress at the outlet of the leads must be removed. The
bending radius should be at least 0.75 mm.
Tensile strength: Test Ua1:
Leads
≤0.25 mm = 1.0 N
≤0.35 mm = 2.5 N
≤0.50 mm = 5.0 N
≤0.80 mm = 10.0 N
≤1.25 mm = 20.0 N
0.25 <
0.35 <
0.50 <
0.80 <
Please read Cautions and warnings and
Important notes at the end of this document.
Page 12 of 19
Temperature measurement
B57875S
S875
Leaded NTC thermistors, lead spacing 5 mm
Bending strength: Test Ub:
Two 90°-bends in opposite directions at a weight of 0.25 kg.
Torsional strength: Test Uc: severity 2
The lead is bent by 90° at a distance of 6 to 6.5 mm from the thermistor body.
The bending radius of the leads should be approx. 0.75 mm. Two torsions of
180° each (severity 2).
When subjecting leads to mechanical stress, the following should be observed:
Tensile stress on leads
During mounting and operation tensile forces on the leads are to be avoided.
Bending of leads
Bending of the leads directly on the thermistor body is not permissible.
A lead may be bent at a minimum distance of twice the wire's diameter +2 mm from the solder
joint on the thermistor body. During bending the wire must be mechanically relieved at its outlet.
The bending radius should be at least 0.75 mm.
Twisting of leads
The twisting (torsion) by 180° of a lead bent by 90° is permissible at 6 mm from the bottom of the
thermistor body.
4
Sealing and potting
When thermistors are sealed, potted or overmolded, there must be no mechanical stress caused
by thermal expansion during the production process (curing / overmolding process) and during
later operation. The upper category temperature of the thermistor must not be exceeded. Ensure
that the materials used (sealing / potting compound and plastic material) are chemically neutral.
5
Cleaning
If cleaning is necessary, mild cleaning agents such as ethyl alcohol and cleaning gasoline are
recommended. Cleaning agents based on water are not allowed. Ultrasonic cleaning methods are
permissible.
6
Storage
In order to maintain their solderability, thermistors must be stored in a non-corrosive atmosphere.
Humidity, temperature and container materials are critical factors.
Do not store SMDs where they are exposed to heat or direct sunlight. Otherwise, the packing ma-
terial may be deformed or SMDs may stick together, causing problems during mounting. After
opening the factory seals, such as polyvinyl-sealed packages, use the SMDs as soon as possible.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 13 of 19
Temperature measurement
B57875S
S875
Leaded NTC thermistors, lead spacing 5 mm
The components should be left in the original packing. Touching the metallization of unsoldered
thermistors may change their soldering properties.
Storage temperature:
ꢀ25 °C up to 45 °C
Relative humidity (without condensation):
≤75% annual mean
<95%, maximum 30 days per annum
Solder the thermistors listed in this data book after shipment from EPCOS within the time speci-
fied:
SMDs:
12 months
24 months
Leaded components:
Please read Cautions and warnings and
Important notes at the end of this document.
Page 14 of 19
Temperature measurement
B57875S
S875
Leaded NTC thermistors, lead spacing 5 mm
Cautions and warnings General
See "Important notes" at the end of this document.
Storage
Store thermistors only in original packaging. Do not open the package prior to storage.
Storage conditions in original packaging: storage temperature ꢀ25 °C ... +45 °C, relative
humidity ≤75% annual mean, <95% maximum 30 days per annum, dew precipitation is
inadmissible.
Do not store thermistors where they are exposed to heat or direct sunlight. Otherwise, the
packing material may be deformed or components may stick together, causing problems during
mounting.
Avoid contamination of thermistor surface during storage, handling and processing.
Avoid storage of thermistors in harmful environments like corrosive gases (SOx, Cl etc).
Use the components as soon as possible after opening the factory seals, i.e. the
polyvinyl-sealed packages.
Solder thermistors within the time specified after shipment from EPCOS.
For leaded components this is 24 months, for SMDs 12 months.
Handling
NTC thermistors must not be dropped. Chip-offs or any other damage must not be caused
during handling of NTCs.
Do not touch components with bare hands. Gloves are recommended.
Avoid contamination of thermistor surface during handling.
Bending / twisting leads
A lead (wire) may be bent at a minimum distance of twice the wire’s diameter plus 4 mm from
the component head or housing. When bending ensure the wire is mechanically relieved at the
component head or housing. The bending radius should be at least 0.75 mm.
Twisting (torsion) by 180° of a lead bent by 90° is permissible at 6 mm from the bottom of the
thermistor body.
Soldering
Use resin-type flux or non-activated flux.
Insufficient preheating may cause ceramic cracks.
Rapid cooling by dipping in solvent is not recommended.
Complete removal of flux is recommended.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 15 of 19
Temperature measurement
B57875S
S875
Leaded NTC thermistors, lead spacing 5 mm
Mounting
Ensure that no thermo-mechanical stress occurs due to production processes (curing or
overmolding processes) when thermistors are sealed, potted or overmolded or during their
subsequent operation. The maximum temperature of the thermistor must not be exceeded.
Ensure that the materials used (sealing/potting compound and plastic material) are chemically
neutral.
Electrodes/contacts must not be scratched or damaged before/during/after the mounting
process.
Contacts and housing used for assembly with the thermistor must be clean before mounting.
Ensure that adjacent materials are designed for operation at temperatures comparable to the
surface temperature of the thermistor. Be sure that surrounding parts and materials can
withstand the temperature.
Avoid contamination of the thermistor surface during processing.
The connections of sensors (e.g. cable end, wire end, plug terminal) may only be exposed to
an environment with normal atmospheric conditions.
Tensile forces on cables or leads must be avoided during mounting and operation.
Bending or twisting of cables or leads directly on the thermistor body is not permissible.
Avoid using chemical substances as mounting aids. It must be ensured that no water or other
liquids enter the NTC thermistors (e.g. through plug terminals). In particular, water based
substances (e.g. soap suds) must not be used as mounting aids for sensors.
Operation
Use thermistors only within the specified operating temperature range.
Use thermistors only within the specified power range.
Environmental conditions must not harm the thermistors. Only use the thermistors under
normal atmospheric conditions or within the specified conditions.
Contact of NTC thermistors with any liquids and solvents should be prevented. It must be
ensured that no water enters the NTC thermistors (e.g. through plug terminals). For
measurement purposes (checking the specified resistance vs. temperature), the component
must not be immersed in water but in suitable liquids (e.g. Galden).
Avoid dewing and condensation unless thermistor is specified for these conditions.
Bending or twisting of cables and/or wires is not permissible during operation of the sensor in
the application.
Be sure to provide an appropriate fail-safe function to prevent secondary product damage
caused by malfunction.
This listing does not claim to be complete, but merely reflects the experience of EPCOS AG.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 16 of 19
Temperature measurement
B57875S
S875
Leaded NTC thermistors, lead spacing 5 mm
Symbols and terms
Symbol
English
German
Fläche
A
Area
AWG
American Wire Gauge
Amerikanische Norm für Drahtquerschnitte
B
B value
B-Wert
B25/100
B value determined by resistance
measurement at 25 °C and 100 °C
B-Wert, ermittelt durch Widerstands-
messungen bei 25 °C und 100 °C
Cth
I
Heat capacitance
Current
Wärmekapazität
Strom
N
Number (integer)
Anzahl (ganzzahliger Wert)
P25
Pdiss
Pel
Maximum power at 25 °C
Power dissipation
Electrical power
Maximale Leistung bei 25 °C
Verlustleistung
Elektrische Leistung
Pmax
Maximum power within stated
temperature range
Maximale Leistung im
angegebenenTemperaturbereich
∆RB/RB
Resistance tolerance caused by
spread of B value
Insulation resistance
Parallel resistance
Widerstandstoleranz, die durch die
Streuung des B-Wertes verursacht wird
Isolationswiderstand
Rins
RP
Parallelwiderstand
RR
Rated resistance
Nennwiderstand
∆RR/RR
RS
Resistance tolerance
Series resistance
Widerstandstoleranz
Serienwiderstand
RT
Resistance at temperature T
(e.g. R25 = resistance at 25 °C)
Widerstand bei Temperatur T
(z.B. R25 = Widerstand bei 25 °C)
T
Temperature
Temperatur
∆T
t
Temperature tolerance
Time
Temperaturtoleranz
Zeit
TA
Tmax
Ambient temperature
Upper category temperature
Umgebungstemperatur
Obere Grenztemperatur
(Kategorietemperatur)
Untere Grenztemperatur
(Kategorietemperatur)
Tmin
Lower category temperature
Top
TR
Tsurf
Operating temperature
Rated temperature
Surface temperature
Betriebstemperatur
Nenntemperatur
Oberflächentemperatur
V
Voltage
Spannung
Vins
Vop
Vtest
Insulation test voltage
Operating voltage
Test voltage
Isolationsprüfspannung
Betriebsspannung
Prüfspannung
Please read Cautions and warnings and
Important notes at the end of this document.
Page 17 of 19
Temperature measurement
B57875S
S875
Leaded NTC thermistors, lead spacing 5 mm
Symbol
English
German
α
Temperature coefficient
Tolerance, change
Dissipation factor
Temperaturkoeffizient
Toleranz, Änderung
Wärmeleitwert
∆
δth
τc
τa
Thermal cooling time constant
Thermal time constant
Thermische Abkühlzeitkonstante
Thermische Zeitkonstante
Abbreviations / Notes
Symbol
English
German
Surface-mounted devices
Oberflächenmontierbares Bauelement
*
To be replaced by a number in ordering Platzhalter für Zahl im Bestellnummern-
codes, type designations etc.
code oder für die Typenbezeichnung.
Platzhalter für einen Buchstaben.
Alle Maße sind in mm angegeben.
+
To be replaced by a letter.
All dimensions are given in mm.
The commas used in numerical values Verwendete Kommas in Zahlenwerten
denote decimal points. bezeichnen Dezimalpunkte.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 18 of 19
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical re-
quirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incum-
bent on the customer to check and decide whether an EPCOS product with the properties de-
scribed in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Ma-
terial Data Sheets on the Internet (www.epcos.com/material). Should you have any more de-
tailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the fore-
going for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver-
sion of the "General Terms of Delivery for Products and Services in the Electrical In-
dustry" published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DSSP,
MiniBlue, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, SIFERRIT,
SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse,
WindCap are trademarks registered or pending in Europe and in other countries. Further
information will be found on the Internet at www.epcos.com/trademarks.
Page 19 of 19
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明