B59100-C160-A70 [EPCOS]
RESISTOR, TEMPERATURE DEPENDENT, PTC, 100ohm, THROUGH HOLE MOUNT, RADIAL LEADED, ROHS COMPLIANT;型号: | B59100-C160-A70 |
厂家: | EPCOS |
描述: | RESISTOR, TEMPERATURE DEPENDENT, PTC, 100ohm, THROUGH HOLE MOUNT, RADIAL LEADED, ROHS COMPLIANT 温度传感 电阻器 |
文件: | 总8页 (文件大小:336K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PTC thermistors
Limit temperature sensors,
leaded disks, coated
Series/Type:
B59100
Date:
March 2006
© EPCOS AG 2006. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Sensors
Limit temperature sensors, leaded disks, coated
C100
Applications
Limit temperature monitoring
Features
Tinned leads
Manufacturer's logo and type designation stamped on in white
Characteristics for nominal threshold temperatures of 90 to 160 °C conform with DIN 44081
RoHS compatible
Delivery mode
Cardboard strips (standard), cardboard tape reeled or in Ammo pack on request
Dimensional drawing
Dimensions in mm
General technical data
Max. operating voltage
Max. measuring voltage
Rated resistance
(TA = 0 ... 40 °C)
(TA ꢀ25 K ... TNTT + 23 K)
(VPTC ≤ 2.5 V)
Vmax
Vmeas,max
RR
30
7.5
≤1001)
VDC
VDC
Ω
Thermal threshold time
ta
<5
s
Operating temperature range (V ≤ Vmeas,max
)
Top
Top
ꢀ40/ TNTT +23
0/+40
°C
°C
Operating temperature range (V = Vmax
)
1) Exception: B59100C0920A070: RR > 100 kΩ; B59100C0010A070: RR > 5 kΩ; B59100C0050A070: RR < 150 Ω
Please read Important notes and
Page 2 of 8
Cautions and warnings at the end of this document.
Sensors
Limit temperature sensors, leaded disks, coated
C100
Electrical specifications and ordering codes
TNTT
R
R
R
R
Ordering code
(TNTT ꢀ ∆T)
(VPTC ≤ 2.5 V)
Ω
(TNTT + ∆T)
(VPTC ≤ 2.5 V)
Ω
(TNTT + 15 K)
(VPTC ≤ 7.5 V)
Ω
(TNTT + 23 K)
(VPTC ≤ 2.5 V)
Ω
°C
∆T = 5 K
- 20
10
≤ 2300
≤ 2300
≤ 550
≤ 550
≤ 550
≤ 550
≤ 550
≤ 550
≤ 550
≤ 550
≤ 550
≤ 400
≤ 570
≤ 570
≤ 570
≤ 550
≥ 2300
≥ 2300
≥ 1330
≥ 1330
≥ 1330
≥ 1330
≥ 1330
≥ 1330
≥ 1330
≥ 1330
≥ 1330
≥ 400
-
-
≥ 10 k
≥ 10 k
-
-
-
-
-
-
B59100C0920A070
B59100C0010A070
B59100C0100A070
B59100C0110A070
B59100C0120A070
B59100C0130A070
B59100C0140A070
B59100C0145A070
B59100C0150A070
B59100C0155A070
B59100C0160A070
B59100C0050A070
B59100C0060A070
B59100C0070A070
B59100C0080A070
B59100C0090A070
≥ 4 k
≥ 4 k
≥ 4 k
≥ 4 k
≥ 4 k
≥ 4 k
≥ 4 k
≥ 4 k
≥ 4 k
-
100
110
120
130
140
145
150
155
160
50
-
-
-
≥ 4 k
≥ 10 k
≥ 10 k
≥ 10 k
-
≥ 570
≥ 570
≥ 570
≥ 1330
-
-
-
60
70
80
90
≥ 4 k
∆T = 6 K
≤ 550
≤ 550
≥ 1330
≥ 1330
≥ 4 k
≥ 4 k
-
-
B59100C0170A070
B59100C0180A070
170
180
Please read Important notes and
Cautions and warnings at the end of this document.
Page 3 of 8
Sensors
Limit temperature sensors, leaded disks, coated
C100
Characteristics (typical)
PTC resistance RPTC versus PTC temperature TPTC
(measured at low signal voltage)
Please read Important notes and
Page 4 of 8
Cautions and warnings at the end of this document.
Sensors
Limit temperature sensors, leaded disks, coated
C100
Characteristics (typical)
PTC resistance RPTC versus PTC temperature TPTC
(measured at low signal voltage)
Please read Important notes and
Page 5 of 8
Cautions and warnings at the end of this document.
Sensors
Limit temperature sensors, leaded disks, coated
C100
Cautions and warnings
General
EPCOS thermistors are designed for specific applications and should not be used for purposes
not identified in our specifications, application notes and data books unless otherwise agreed
with EPCOS during the design-in-phase.
Ensure suitability of thermistor through reliability testing during the design-in phase. The
thermistors should be evaluated taking into consideration worst-case conditions.
Storage
Store thermistors only in original packaging. Do not open the package before storage.
Storage conditions in original packaging: storage temperature ꢀ25 °C ... +45 °C, relative
humidity ≤75% annual mean, maximum 95%, dew precipitation is inadmissible.
Avoid contamination of thermistors surface during storage, handling and processing.
Avoid storage of thermistor in harmful environment with effect on function on long-term
operation (examples given under operation precautions).
Use thermistor within 6 months after delivery.
Handling
PTCs must not be dropped. Chip-offs must not be caused during handling of PTCs.
Components must not be touched with bare hands. Gloves are recommended.
Avoid contamination of thermistor surface during handling.
Soldering
Use rosin-type flux or non-activated flux.
Insufficient preheating may cause ceramic cracks.
Rapid cooling by dipping in solvent is not recommended.
Complete removal of flux is recommended.
Mounting
Electrode must not be scratched before/during/after the mounting process.
Contacts and housing used for assembly with thermistor have to be clean before mounting.
Especially grease or oil must be removed.
When PTC thermistors are encapsulated with sealing material, the precautions given in chapter
"Mounting instructions", "Sealing and potting" must be observed.
When the thermistor is mounted, there must not be any foreign body between the electrode of
the thermistor and the clamping contact.
The minimum force of the clamping contacts pressing against the PTC must be 10 N.
During operation, the thermistor’s surface temperature can be very high. Ensure that adjacent
components are placed at a sufficient distance from the thermistor to allow for proper cooling at
the thermistors.
Ensure that adjacent materials are designed for operation at temperatures comparable to the
surface temperature of thermistor. Be sure that surrounding parts and materials can withstand
this temperature.
Avoid contamination of thermistor surface during processing.
Please read Important notes and
Page 6 of 8
Cautions and warnings at the end of this document.
Sensors
Limit temperature sensors, leaded disks, coated
C100
Operation
Use thermistors only within the specified temperature operating range.
Use thermistors only within the specified voltage and current ranges.
Environmental conditions must not harm the thermistors. Use thermistors only in normal
atmospheric conditions. Avoid use in deoxidizing gases (chlorine gas, hydrogen sulfide gas,
ammonia gas, sulfuric acid gas etc), corrosive agents, humid or salty conditions.Contact with
any liquids and solvents should be prevented.
Be sure to provide an appropriate fail-safe function to prevent secondary product damage
caused by abnormal function (e.g. use VDR for limitation of overvoltage condition).
Please read Important notes and
Page 7 of 8
Cautions and warnings at the end of this document.
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical re-
quirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incum-
bent on the customer to check and decide whether an EPCOS product with the properties de-
scribed in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of passive electronic compon-
ents or failure before the end of their usual service life cannot be completely ruled out
in the current state of the art, even if they are operated as specified. In customer applica-
tions requiring a very high level of operational safety and especially in customer applications
in which the malfunction or failure of a passive electronic component could endanger human
life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured
by means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of a passive electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as “hazardous”). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an or-
der.
We also reserve the right to discontinue production and delivery of products. Con-
sequently, we cannot guarantee that all products named in this publication will always be
available.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver-
sion of the “General Terms of Delivery for Products and Services in the Electrical In-
dustry” published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, EPCOS-JONES, Baoke, CeraDiode, CSSP, MLSC, PhaseCap,
PhaseMod, SIFI, SIKOREL, SilverCap, SIMID, SIOV, SIP5D, SIP5K, UltraCap, WindCap are
trademarks registered or pending in Europe and in other countries. Further information will
be found on the Internet at www.epcos.com/trademarks.
Page 8 of 8
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明