AP-CF001GR9NS-NRA [ETC]
CompactFlash Series 5 Specifications for Industrial CompactFlash Card;
| 型号： | AP-CF001GR9NS-NRA |
| 厂家： | 
ETC |
| 描述： | CompactFlash Series 5 Specifications for Industrial CompactFlash Card |
| 文件： | 总20页 (文件大小：201K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Halogen-free
CompactFlash Series 5
Specifications for Industrial CompactFlash Card
August 7th, 2013
Version 1.2
Apacer Technology Inc.
1F, No.32, Zhongcheng Rd., Tucheng Dist., New Taipei City, Taiwan, R.O.C
Tel: +886-2-2267-8000 Fax: +886-2-2267-2261
www.apacer.com
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
Features:
ꢀ
CompactFlash Association Specification
Revision 4.1 Standard Interface
512 bytes per sector
ꢀ
Temperature ranges
–
–
–
0°C to 70°C for operation (Standard)
-40°C to 85°C for operation (Extended)
-40°C to 100°C for storage
–
–
–
ATA command set compatible
ATA transfer mode supports:
PIO Mode 6
Multiword DMA Mode 4
Ultra DMA Mode 5
PCMCIA UDMA Mode 5
ꢀ
ꢀ
Operating voltage
3.3 V
5.0 V
–
–
Power consumption (typical)**
Active mode: 175 mA
Standby mode: 3 mA
–
–
ꢀ
ꢀ
ꢀ
Capacities
–
128, 256, 512 MB
1, 2, 4, 8, 16, 32, 64 GB
ꢀ
ꢀ
ꢀ
Connector Type
50 pins female
–
–
Performance
Sustained read: Up to 55 MB/sec
Sustained write: Up to 42 MB/sec
–
–
Physical Dimensions
36.4mm x 42.8mm x 3.3mm
Intelligent ATA/IDE module
Endurance (TBW: Terabytes Written)
128 MB: 0.5 TBW
256 MB: 1.1 TBW
512 MB: 2.3 TBW
1 GB: 4.5 TBW
–
Wear-leveling algorithms to substantially
increase longevity of flash media
Built-in BCH ECC capable of correcting
up to 24 bits in 1,024 byte data
Flash block management
–
–
–
–
–
–
–
–
–
–
–
–
–
–
2 GB: 9.1 TBW
4 GB: 18.2 TBW
8 GB: 36.5 TBW
16 GB: 73.0 TBW
32 GB: 146.0 TBW
64 GB: 292.1 TBW
Power failure management
Supports S.M.A.R.T commands
ꢀ
NAND Flash Type: SLC
ꢀ
Halogen free
*Performance and power consumption may vary depending on host system configurations.
1
© 2013 Apacer Technology Inc.
Rev. 1.2
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
Table of Contents
1. GENERAL DESCRIPTION.................................................................................................... 3
1.1 INTELLIGENT
COMPACTFLASH MODULE .............................................................................................................3
1.1.1 Wear-leveling algorithms .............................................................................................................................3
1.1.2 S.M.A.R.T. Technology .................................................................................................................................3
1.1.3 Built-in Hardware ECC................................................................................................................................3
1.1.4 Flash Block Management .............................................................................................................................3
1.1.5 Power Failure Management.........................................................................................................................4
2. FUNCTIONAL BLOCK .......................................................................................................... 4
3. PIN ASSIGNMENTS ............................................................................................................... 5
4. PRODUCT SPECIFICATION................................................................................................ 7
4.1 CAPACITY.............................................................................................................................................................7
4.2 PERFORMANCE .....................................................................................................................................................7
4.3 ENVIRONMENTAL SPECIFICATIONS.......................................................................................................................8
4.4 CERTIFICATION & COMPLIANCE...........................................................................................................................8
4.5 ENDURANCE ........................................................................................................................................................8
5. SOFTWARE INTERFACE.................................................................................................... 9
5.1 CF-ATA COMMAND SET......................................................................................................................................9
6. ELECTRICAL SPECIFICATION ...................................................................................... 10
7. PHYSICAL CHARACTERISTICS..................................................................................... 11
7.1 DIMENSION.........................................................................................................................................................11
8. PRODUCT ORDERING INFORMATION........................................................................ 12
8.1 PRODUCT
8.2 VALID
CODE DESIGNATIONS .........................................................................................................................12
C
OMBINATIONS.......................................................................................................................................13
2
© 2013 Apacer Technology Inc.
Rev. 1.2
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
1. General Description
Apacer’s value-added Industrial CompactFlash Card offers high performance, high reliability and power-
efficient storage. Regarding standard compliance, this CompactFlash Card complies with CompactFlash
specification revision 4.1, supporting transfer modes up to Programmed Input Output (PIO) Mode 6, Multi-
word Direct Memory Access (DMA) Mode 4, Ultra DMA Mode 5, and PCMCIA Ultra DMA Mode 5.
Apacer’s value-added CFC provides complete PCMCIA – ATA functionality and compatibility. Apacer ‘s
CompactFlash technology is designed for applications in Point of Sale (POS) terminals, telecom, IP-STB,
medical instruments, surveillance systems, industrial PCs and handheld applications such as the new
generation of Digital Single Lens Reflex (DSLR) cameras.
1.1 Intelligent CompactFlash Module
1.1.1 Wear-leveling algorithms
Flash memory devices differ from Hard Disk Drives (HDDs) in terms of how blocks are utilized. For HDDs,
when a change is made to stored data, like erase or update, the controller mechanism on HDDs will
perform overwrites on blocks. On the other hand, NAND flash storage adopts flash as their primary media.
Unlike HDDs, flash blocks cannot be overwritten and each P/E cycle wears down the lifespan of blocks
gradually. Repeatedly program/erase cycles performed on the same memory cells will eventually cause
some blocks to age faster than others. This would bring flash storages to their end of service term earlier.
Wear leveling is an important mechanism that level out the wearing of blocks so that the wearing-down of
blocks can be almost evenly distributed. This will increase the lifespan of SSDs. Commonly used wear
leveling types are Static and Dynamic.
1.1.2 S.M.A.R.T. Technology
S.M.A.R.T. is an acronym for Self-Monitoring, Analysis and Reporting Technology, an open standard
allowing disk drives to automatically monitor their own health and report potential problems. It protects the
user from unscheduled downtime by monitoring and storing critical drive performance and calibration
parameters. Ideally, this should allow taking proactive actions to prevent impending drive failure. Apacer
SMART feature adopts the standard SMART command B0h to read data from the drive. When the Apacer
SMART Utility running on the host, it analyzes and reports the disk status to the host before the device is
in critical condition.
1.1.3 Built-in Hardware ECC
This CompactFlash card employs BCH Error Correction Code (ECC) algorithms. This on-chip hardware
BCH-ECC engines is 13/24 bit programmed that can correct up to 24-bit errors per 1,024 byte data. This
built-in hardware ECC performs parity generation and error detection/correction for data integrity.
1.1.4 Flash Block Management
Contemporary process technology is unable to guarantee total reliability of NAND flash memory array.
When a flash memory device leaves factory, it comes with a highly minimal number of initial bad block
during production or out-of-factory as there is no currently known technology that produce flash chips free
of bad blocks. On the other hand, bad blocks may develop during program/erase cycles. When host
performs program/erase command on a block, bad block may appear in Status Register. Since bad
blocks are inevitable, the solution is to keep them in control. Apacer flash devices are programmed with
ECC, block mapping technique and S.M.A.R.T to reduce invalidity or error. Once bad blocks are detected,
data in those blocks will be transferred to free blocks and error will be corrected by designated algorithms.
3
© 2013 Apacer Technology Inc.
Rev. 1.2
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
1.1.5 Power Failure Management
Power Failure Management plays a crucial role when experiencing unstable power supply. Power
disruption may occur when users are storing data into the SSD. In this urgent situation, the controller
would run multiple write-to-flash cycles to store the metadata for later block rebuilding. This urgent
operation requires about several milliseconds to get it done. At the next power up, the firmware will
perform a status tracking to retrieve the mapping table and resume previously programmed NAND blocks
to check if there is any incompleteness of transmission
2. Functional Block
The CompactFlash Card (CFC) includes a controller and flash media, as well as the CompactFlash
standard interface. Figure 2-1 shows the functional block diagram.
Figure 2-1: Functional block diagram
4
© 2013 Apacer Technology Inc.
Rev. 1.2
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
3. Pin Assignments
Table 3-1 lists the pin assignments with respective signal names for the 50-pin configuration. A “#” suffix
indicates the active low signal. The pin type can be input, output or input/output.
Table 3-1: Pin assignments (1 of 2)
Pin No.
Memory card mode
I/O card mode
True IDE mode
Signal name Pin I/O type
Signal name
Pin I/O type
Signal name Pin I/O type
1
GND
D3
D4
D5
D6
-
I/O
I/O
I/O
GND
D3
D4
D5
D6
-
I/O
I/O
I/O
GND
D3
D4
D5
D6
-
I/O
I/O
I/O
2
3
4
5
6
I/O
I/O
I/O
I/O
I/O
I/O
D7
D7
D7
7
8
9
#CE1
A10
#OE
A9
A8
A7
VCC
A6
A5
A4
A3
I
I
I
#CE1
A10
#OE
A9
A8
A7
VCC
A6
A5
A4
A3
I
I
I
#CS0
A101
#ATA SEL
A91
I
I
I
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
I
I
I
I
I
I
A81
I
-
I
-
A71
I
-
VCC
A61
I
I
I
I
I
I
I
I
I
A51
A41
I
I
I
I
A31
A2
I
I
A2
A1
A0
D0
A2
A1
A0
D0
I
I
I
I
A1
A0
D0
D1
I
I
I/O
I/O
I/O
O
O
O
I/O
I/O
I/O
I/O
I/O
I
I/O
I/O
I/O
O
O
O
I/O
I/O
I/O
I/O
I/O
I
I/O
I/O
I/O
O
O
O
I/O
I/O
I/O
I/O
I/O
I
D1
D2
D1
D2
D2
WP
#IOIS16
#CD2
#CD1
D11
D12
D13
D14
D15
#CE2
#VS1
#IORD
#IOWR
#WE
#IREQ
VCC
#CSEL
#VS2
RESET
#IOCS16
#CD2
#CD1
D11
#CD2
#CD1
D11
D12
D13
D14
D15
#CE2
#VS1
#IORD
#IOWR
#WE
RDY/-BSY
VCC
#CSEL
#VS2
RESET
D12
D13
D14
D15
#CS1
#VS1
#IORD
#IOWR
#WE
INTRQ
VCC
#CSEL
#VS2
#RESET
O
I
I
O
I
I
O
I
I
I
O
-
I
O
I
I
O
-
I
O
I
I
O
-
I
O
I
5
© 2013 Apacer Technology Inc.
Rev. 1.2
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
Table 3-1: Pin assignments (2 of 2)
Pin No.
Memory card mode
Signal name Pin I/O type
I/O card mode
True IDE mode
Signal name
Pin I/O type
Signal name Pin I/O type
42
43
44
45
46
47
48
49
50
#WAIT
#INPACK
#REG
BVD2
BVD1
D8
O
O
I
#WAIT
#INPACK
#REG
#SPKR
#STSCHG
D8
O
O
I
IORDY
DMARQ2
DMACK2
#DASP
#PDIAG
D8
O
O
I
I/O
I/O
I/O
I/O
I/O
-
O
O
O
O
I/O
I/O
I/O
-
I/O
I/O
I/O
-
D9
D10
GND
D9
D10
GND
D9
D10
GND
1.
2.
The signal should be grounded by the host.
Connection required when UDMA is in use.
6
© 2013 Apacer Technology Inc.
Rev. 1.2
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
4. Product Specification
4.1 Capacity
Capacity specification of the Compact Flash Card series (CFC) is available as shown in Table 4-1. It lists
the specific capacity and the default numbers of heads, sectors and cylinders for each product line.
Table 4-1: Capacity specifications
Capacity
128 MB
256 MB
512 MB
1GB
Total bytes1
128,450,560
Cylinders
980
Heads
8
Sectors
32
Max LBA
250,880
256,901,120
980
16
32
501,760
512,483,328
993
16
63
1,000,944
2,001,888
4,001,760
8,027,712
16,007,040
32,014,336
62,537,728
125,059,072
1,024,966,656
2,048,901,120
4,110,188,544
8,195,604,480
16,391,340,032
32,019,316,736
64,030,244,864
1,986
3,970
7,964
15,880
16,383
16,383
16,383
16
63
2GB
16
63
4GB
16
63
8GB
16
63
16GB
32GB
64 GB
16
63
16
63
16
83
Notes:
Display of total bytes varies from operating systems.
Cylinders, heads or sectors are not applicable for these capacities. Only LBA addressing applies
Notes: 1 GB = 1,000,000,000 bytes; 1 sector = 512 bytes.
LBA count addressed in the table above indicates total user storage capacity and will remain the same throughout the lifespan of the
device. However, the total usable capacity of the SSD is most likely to be less than the total physical capacity because a small portion
of the capacity is reserved for device maintenance usages.
4.2 Performance
Performances of the CF cards are listed in Table 4-2
Table 4-2: Performance specifications
Capacity
128 MB
256 MB
512 MB
1 GB
2 GB
4 GB
8 GB
16 GB
32 GB
64 GB
Performance
Sustained
read (MB/s)
21
6
24
6
47
22
45
19
55
25
55
35
55
42
48
38
57
27
50
26
Sustained
write (MB/s)
Notes: performance may vary depending on flash configurations or host system settings.
7
© 2013 Apacer Technology Inc.
Rev. 1.2
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
4.3 Environmental Specifications
Environmental specification of the Compact Flash Card series (CFC) which follows the MIL-STD-810F
standards is available as shown in Table 4-3.
Table 4-3: Environmental specifications
Environment
Specification
Operation
Storage
0°C to 70°C; -40°C to 85°C (Extended Temperature)
-40°C to 100°C
Temperature
Vibration (Non-Operation)
Shock (Non-Operation)
Sine wave : 10~2000Hz, 15G (X, Y, Z axes)
Half sine wave 1,500G (X, Y, Z ; All 6 axes)
4.4 Certification & Compliance
The CompactFlash card complies with the following global standards:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
CE
FCC
Halogen-free
CompactFlash Association Specification Revision 4.1
EMC
4.5 Endurance
The endurance of a storage device is predicted by TeraBytes Written based on several factors related to
usage, such as the amount of data written into the drive, block management conditions, and daily
workload for the drive. Thus, key factors, such as Write Amplifications and the number of P/E cycles, can
influence the lifespan of the drive.
Capacity
128 MB
256 MB
512 MB
1 GB
TeraBytes Written
0.5
1.1
2.3
4.5
2 GB
9.1
4 GB
18.2
36.5
73.0
146.0
292.1
8 GB
16 GB
32 GB
64 GB
Notes:
ꢁ
ꢁ
The measurement assumes the data written to the SSD for test is under a typical and constant rate.
The measurement follows the standard metric: 1 TB (Terabyte) = 1000 GB.
8
© 2013 Apacer Technology Inc.
Rev. 1.2
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
5. Software Interface
5.1 CF-ATA Command Set
Table 5-1: CFC-ATA command set
Command
Code
E5H or 98H
90H
Check-Power-Mode
Execute-Drive-Diagnostic
Erase-Sector(s)
Flush-Cache
C0H
E7H
Format-Track
Identify-Drive
Idle
50H
ECH
E3H or 97H
E1H or 95H
91H
Idle-Immediate
Initialize-Drive-Parameters
NOP
00H
Read-Buffer
E4H
Read-Multiple
Read-Sector(s)
Read-Verify-Sector(s)
Recalibrate
C4H
20H or 21H
40H or 41H
1XH
Request-Sense
Seek
03H
7XH
Set-Features
EFH
C6H
Set-Multiple-mode
Set-Sleep-Mode
Standby
E6H or 99H
E2H or 96H
E0H or 94H
87H
Standby-Immediate
Translate-Sector
Write-Buffer
E8H
Write-Multiple
C5H
Write-Multiple-Without-Erase
Write-Sector(s)
CDH
30H or 31H
38H
Write-Sector(s)-Without-Erase
Write-Verify
3CH
9
© 2013 Apacer Technology Inc.
Rev. 1.2
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
6. Electrical Specification
Caution: Absolute Maximum Stress Ratings – Applied conditions greater than those listed under
“Absolute Maximum Stress Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these conditions or conditions greater than those defined in
the operational sections of this data sheet is not implied. Exposure to absolute maximum stress rating
conditions may affect device reliability.
Table 6-1: Operating range
Standard Operating Temperature
0°C to +70°C
Extended Operating Temperature
Supply voltage
-40°C to +85°C
5
4.75-5.25V)
3.135-3.465V)
3.3V
Table 6-2: Absolute maximum power pin stress ratings
Parameter
Symbol
VDD
Conditions
Input Power
-0.3V min. to 6.5V max.
-0.5V min. to VDD + 0.5V max.
Voltage on any pin except VDD with respect to GND
V
10
© 2013 Apacer Technology Inc.
Rev. 1.2
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
7. Physical Characteristics
7.1 Dimension
Unit: mm
F
IGURE 7-1: Physical dimension
11
© 2013 Apacer Technology Inc.
Rev. 1.2
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
8. Product Ordering Information
8.1 Product Code Designations
A P – CF x x x x R X X S – XXXXXX A
Firmware version
Specification
RM: Removable
NR: Non-Removable
ET: Extended Temperature
NDRM: Non-DMA + Removable
NDNR: Non-DMA + Non-Removable
ETRM: Ext. Temp. + Removable
ETNR: Ext. Temp. + Non-Removable
ETNDRM: Ext. Temp + Non-DMA + Removable
ETNDNR: Ext. Temp + Non-DMA + Non-Removable
Halogen Free Compliant
Configuration
F
Dual Channel
N : Standard
CTL Type
7: CTL BGA Package
9: CTL TSOP Package
CFC Type
Capacities:
128M
256M
512M
001G:
002G
004G:
008G
016G
032G
064G
128MB
256MB
512MB
1GB
2GB
4GB
8GB
16GB
32GB
64GB
Model Name
Apacer Product Code
12
© 2013 Apacer Technology Inc.
Rev. 1.2
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
8.2 Valid Combinations
8.2.1 Standard Temperature
8.2.1.1 Non-Removable
Capacity
AP/N
128MB
256MB
512MB
1GB
AP-CF128MR9NS-NRA
AP-CF256MR9NS-NRA
AP-CF512MR9NS-NRA
AP-CF001GR9NS-NRA
AP-CF002GR9NS-NRA
AP-CF004GR9NS-NRA
AP-CF008GR9NS-NRA
AP-CF016GR9FS-NR
AP-CF032GR9FS-NR
AP-CF064GR7FS-NR
2GB
4GB
8GB
16GB
32GB
64GB
8.2.1.2 Removable
Capacity
128MB
256MB
512MB
1GB
AP/N
AP-CF128MR9NS-RMA
AP-CF256MR9NS-RMA
AP-CF512MR9NS-RMA
AP-CF001GR9NS-RMA
AP-CF002GR9NS-RMA
AP-CF004GR9NS-RMA
AP-CF008GR9NS-RMA
AP-CF016GR9FS-RM
AP-CF032GR9FS-RM
AP-CF064GR7FS-RM
2GB
4GB
8GB
16GB
32GB
64GB
13
© 2013 Apacer Technology Inc.
Rev. 1.2
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
8.2.1.3 Non-DMA + Removable
Capacity
128MB
256MB
512MB
1GB
AP/N
AP-CF128MR9NS-NDRMA
AP-CF256MR9NS-NDRMA
AP-CF512MR9NS-NDRMA
AP-CF001GR9NS-NDRMA
AP-CF002GR9NS-NDRMA
AP-CF004GR9NS-NDRMA
AP-CF008GR9NS-NDRMA
AP-CF016GR9FS-NDRM
AP-CF032GR9FS-NDRM
AP-CF064GR7FS-NDRM
2GB
4GB
8GB
16GB
32GB
64GB
8.2.1.4 Non-DMA + Non-Removable
Capacity
128MB
256MB
512MB
1GB
AP/N
AP-CF128MR9NS-NDNRA
AP-CF256MR9NS-NDNRA
AP-CF512MR9NS-NDNRA
AP-CF001GR9NS-NDNRA
AP-CF002GR9NS-NDNRA
AP-CF004GR9NS-NDNRA
AP-CF008GR9NS-NDNRA
AP-CF016GR9FS-NDNR
AP-CF032GR9FS-NDNR
AP-CF064GR7FS-NDNR
2GB
4GB
8GB
16GB
32GB
64GB
Note: Please consult with Apacer sales representatives for availabilities.
14
© 2013 Apacer Technology Inc.
Rev. 1.2
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
8.2.2 Extended Temperature
8.2.2.1 Ext. Temp. + Non-Removable
Capacity
128MB
256MB
512MB
1GB
AP/N
AP-CF128MR9NS-ETNRA
AP-CF256MR9NS-ETNRA
AP-CF512MR9NS-ETNRA
AP-CF001GR9NS-ETNRA
AP-CF002GR9NS-ETNRA
AP-CF004GR9NS-ETNRA
AP-CF008GR9NS-ETNRA
AP-CF016GR9FS-ETNR
AP-CF032GR9FS-ETNR
AP-CF064GR7FS-ETNR
2GB
4GB
8GB
16GB
32GB
64GB
8.2.2.2 Ext. Temp. + Removable
Capacity
128MB
256MB
512MB
1GB
AP/N
AP-CF128MR9NS-ETRMA
AP-CF256MR9NS-ETRMA
AP-CF512MR9NS-ETRMA
AP-CF001GR9NS-ETRMA
AP-CF002GR9NS-ETRMA
AP-CF004GR9NS-ETRMA
AP-CF008GR9NS-ETRMA
AP-CF016GR9FS-ETRM
AP-CF032GR9FS-ETRM
AP-CF064GR7FS-ETRM
2GB
4GB
8GB
16GB
32GB
64GB
15
© 2013 Apacer Technology Inc.
Rev. 1.2
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
8.2.2.3 Non-DMA + Removable
Capacity
128MB
256MB
512MB
1GB
AP/N
AP-CF128MR9NS-ETNDRMA
AP-CF256MR9NS-ETNDRMA
AP-CF512MR9NS-ETNDRMA
AP-CF001GR9NS-ETNDRMA
AP-CF002GR9NS-ETNDRMA
AP-CF004GR9NS-ETNDRMA
AP-CF008GR9NS-ETNDRMA
AP-CF016GR9FS-ETNDRM
AP-CF032GR9FS-ETNDRM
AP-CF064GR7FS-ETNDRM
2GB
4GB
8GB
16GB
32GB
64GB
8.2.2.4 Non-DMA + Non-Removable
Capacity
128MB
256MB
512MB
1GB
AP/N
AP-CF128MR9NS-ETNDNRA
AP-CF256MR9NS-ETNDNRA
AP-CF512MR9NS-ETNDNRA
AP-CF001GR9NS-ETNDNRA
AP-CF002GR9NS-ETNDNRA
AP-CF004GR9NS-ETNDNRA
AP-CF008GR9NS-ETNDNRA
AP-CF016GR9FS-ETNDNR
AP-CF032GR9FS-ETNDNR
AP-CF064GR7FS-ETNDNR
2GB
4GB
8GB
16GB
32GB
64GB
Note: Please consult with Apacer sales representatives for availabilities.
16
© 2013 Apacer Technology Inc.
Rev. 1.2
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
Revision History
Revision Date
Description
Remark
1.0
1.1
06/19/2012
Official release
09/07/2012
08/07/2013
Revised Product Ordering Information
Updated performance and product ordering
information due to change in NAND flash use
1.2
Updated the address of Taiwan headquarter
Added endurance (TBW) section
17
© 2013 Apacer Technology Inc.
Rev. 1.2
Compact Flash 5 series
AP-CFxxxxRXXS-XXXXXXA
Global Presence
Apacer Technology Inc.
Apacer Technology Inc.
Taiwan (Headquarters)
1F., No.32, Zhongcheng Rd., Tucheng Dist.,
New Taipei City 236, Taiwan R.O.C.
Tel: 886-2-2267-8000
Fax: 886-2-2267-2261
amtsales@apacer.com
Apacer Memory America, Inc.
386 Fairview Way, Suite102,
Milpitas, CA 95035
Tel: 1-408-518-8699
Fax: 1-408-935-9611
sa@apacerus.com
U.S.A.
Japan
Europe
China
India
Apacer Technology Corp.
5F, Matsura Bldg., Shiba, Minato-Ku
Tokyo, 105-0014, Japan
Tel: 81-3-5419-2668
Fax: 81-3-5419-0018
jpservices@apacer.com
Apacer Technology B.V.
Science Park Eindhoven 5051 5692 EB Son,
The Netherlands
Tel: 31-40-267-0000
Fax: 31-40-267-0000#6199
sales@apacer.nl
Apacer Electronic (Shanghai) Co., Ltd
1301, No.251,Xiaomuqiao Road, Shanghai,
200032, China
Tel: 86-21-5529-0222
Fax: 86-21-5206-6939
sales@apacer.com.cn
Apacer Technologies Pvt. Ltd.
# 535, 1st Floor, 8th cross, JP Nagar 3rd Phase,
Bangalore – 560078, India
Tel: 91-80-4152-9061
sales_india@apacer.com
18
© 2013 Apacer Technology Inc.
Rev. 1.2
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Apacer:
AP-CF128MR9NS-NDNRA AP-CF008GR9NS-ETNRA AP-CF064GR7FS-NR AP-CF001GR9NS-ETNRA AP-
CF001GR9NS-ETNDNRA AP-CF016GR9FS-NDNR AP-CF001GR9NS-NRA AP-CF032GR9FS-ETNR AP-
CF004GR9NS-ETNDNRA AP-CF128MR9NS-NRA AP-CF064GR7FS-NDNR AP-CF256MR9NS-NRA AP-
CF512MR9NS-NRA AP-CF032GR9FS-NDNR AP-CF512MR9NS-ETNDNRA AP-CF032GR9FS-NR AP-
CF002GR9NS-NDNRA AP-CF256MR9NS-ETNDNRA AP-CF002GR9NS-NRA AP-CF256MR9NS-NDNRA AP-
CF004GR9NS-NRA AP-CF512MR9NS-NDNRA AP-CF128MR9NS-ETNRA AP-CF256MR9NS-ETNRA AP-
CF032GR9FS-ETNDNR AP-CF008GR9NS-NRA AP-CF128MR9NS-ETNDNRA AP-CF008GR9NS-ETNDNRA AP-
CF064GR7FS-ETNR AP-CF016GR9FS-ETNR AP-CF001GR9NS-NDNRA AP-CF016GR9FS-ETNDNR AP-
CF004GR9NS-NDNRA AP-CF512MR9NS-ETNRA AP-CF016GR9NS-NR AP-CF002GR9NS-ETNRA AP-
CF064GR7FS-ETNDNR AP-CF008GR9NS-NDNRA AP-CF002GR9NS-ETNDNRA
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明