AP-FD25A20A0008GR-KS [ETC]
Value Added ATA Flash Drive â ¢;型号: | AP-FD25A20A0008GR-KS |
厂家: | ETC |
描述: | Value Added ATA Flash Drive â ¢ |
文件: | 总19页 (文件大小:182K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
RoHS Compliant
Ⅲ
Value Added ATA Flash Drive
Ⅲ
Specification for AFD 253
Mar 18, 2011
Version 1.4
Apacer Technology Inc.
4th Fl., 75 Xintai 5th Rd., Sec.1, Hsichih, New Taipei City, 221, Taiwan
Tel: +886-2-2698-2888
www.apacer.com
Fax: +886-2-2698-2889
Ⅲ
Value Added ATA Flash Drive
AP-FD25A2xAxxxxxR-XXX
Features:
ꢀ
Standard ATA/IDE bus interface
ꢀ
ꢀ
Temperature ranges
–
–
ATA command set compatible
ATA operating mode supports up to:
PIO Mode-4
–
Operation:
Standard: 0°C to 70°C
ET*: -40°C to 85°C
Multiword DMA Mode-2
Ultra DMA Mode-4
–
Storage: -40°C to 100°C
Flash management
ꢀ
ꢀ
Connector type
44-pin male
–
Intelligent endurance design
–
Advanced wear-leveling algorithms
S.M.A.R.T. technology
Built-in hardware ECC
Low power consumption (typical)
–
–
–
Supply voltage: 5V
Active mode: 138mA
Sleep mode: 2000µA
Enhanced data integrity
–
–
Intelligent power failure recovery
Enhanced security level
Secure protection zone
ꢀ
ꢀ
ꢀ
Performance
ATA Secure Erase
–
–
Sustained read: Up to 35 MB/sec
Sustained write: Up to 20 MB/sec
ꢀ
RoHS compliant
Capacity
–
–
256, 512 MB
1, 2, 4, 8, 16, 32, 64 GB
NAND Flash Type: SLC
*Extended Temperature
1
© 2011 Apacer Technology Inc.
Rev. 1.4
Ⅲ
Value Added ATA Flash Drive
AP-FD25A2xAxxxxxR-XXX
Table of Contents
1. GENERAL DESCRIPTION ......................................................................................... 3
1.1 PERFORMANCE-OPTIMIZED
CONTROLLER ...............................................................................................3
1.1.1 Power Management Unit (PMU)...................................................................................................3
1.1.2 SRAM Buffer.................................................................................................................................3
2. FUNCTIONAL BLOCK ............................................................................................... 4
3. PIN ASSIGNMENTS................................................................................................... 5
4. CAPACITY SPECIFICATION ..................................................................................... 6
4.1 PERFORMANCE
SPECIFICATION ..............................................................................................................6
4.2 ENVIRONMENTAL
SPECIFICATIONS ..........................................................................................................6
5. FLASH MANAGEMENT ............................................................................................. 7
5.1 INTELLIGENT
ENDURANCE DESIGN..........................................................................................................7
5.1.1 Advanced wear-leveling algorithms..............................................................................................7
5.1.2 S.M.A.R.T. technology..................................................................................................................7
5.1.3 Built-in hardware ECC ..................................................................................................................7
5.1.4 Enhanced data integrity................................................................................................................7
5.2 INTELLIGENT
5.3 ENHANCED
P
OWER
F
AILURE
R
ECOVERY...............................................................................................8
SECURITY
LEVEL..................................................................................................................8
5.3.1 Secure protection zone.................................................................................................................8
5.3.2 ATA Secure Erase ........................................................................................................................8
6. SOFTWARE INTERFACE ......................................................................................... 9
6.1 COMMAND SET ......................................................................................................................................9
7. ELECTRICAL SPECIFICATION.............................................................................. 11
8. PHYSICAL CHARACTERISTICS............................................................................ 11
9. PRODUCT ORDERING INFORMATION................................................................. 14
9.1 PRODUCT
CODE DESIGNATIONS ...........................................................................................................14
9.2 VALID OMBINATIONS ..........................................................................................................................14
C
2
© 2011 Apacer Technology Inc.
Rev. 1.4
Ⅲ
Value Added ATA Flash Drive
AP-FD25A2xAxxxxxR-XXX
1. General Description
Apacer’s ATA-Flash Drive (AFD) is a high-performance, solid state drive (SSD) designed to replace a
conventional IDE hard disk drive. AFD supports standard ATA/IDE protocol and can be plugged into a
standard IDE connector commonly found in desktop or portable PCs. It is more rugged, reliable and
power-efficient compared to the mechanical hard drive and is designed for use in rugged laptops, military
devices, thin clients, Point of Sale (POS) terminals, telecom, medical instruments, surveillance systems
and industrials PCs. AFD also offers users selectable Master/Slave operation through an external jumper
setting. Apacer AFD Series is the best drop-in replacement for high-maintenance HDD where reliability is
a major concern.
AFD includes a built-in microcontroller and file management firmware that communicates through with the
ATA standard interfaces. This means the AFD does not require any additional or proprietary host software
such as the Flash File System (FFS) and Memory Technology Driver (MTD) software. AFD is designed to
work at 5 Volts, support the standard ATA/IDE protocol up to PIO Mode-4, Multiword DMA Mode-2, and
Ultra DMA Mode-4 interfaces, and use a standard ATA driver that fits to all major operating systems such
as Microsoft’s Windows series, Mac OS family, and UNIX variants
Featuring technologies as Advanced Wear-leveling algorithms, S.M.A.R.T, Enhanced Data Integrity,
Intelligent Power Failure Recovery, Secure Protection Zone and ATA Secure Erase, Apacer’s ADM
assures users of a versatile device on data storage.
1.1 Performance-Optimized Controller
The heart of an ATA-Flash Drive is the ATA controller, which translates standard ATA signals into the
data and controls of the flash media. This proprietary ATA controller is specifically designed to attain high
data throughput from the host to the flash.
1.1.1 Power Management Unit (PMU)
The power management unit (PMU) controls the power consumption of the ATA-Flash Drive controller. It
can dramatically extend product battery life by leaving the idle part of the circuitry into sleep mode. The
PMU has zero wake-up latency.
1.1.2 SRAM Buffer
The SRAM buffer is a key contributor to the ATA controller performance. It optimizes data writes to the
flash.
3
© 2011 Apacer Technology Inc.
Rev. 1.4
Ⅲ
Value Added ATA Flash Drive
AP-FD25A2xAxxxxxR-XXX
2. Functional Block
The ATA-Flash Drive (AFD) includes the ATA controller and flash media, as well as the ATA standard
interface. Figure 2-1 shows the functional block diagram.
Flash Array
Flash
Media
Flash
Media
ATA
Controller
HOST
ATA/IDE Bus
Flash
Media
Flash
Media
.
.
.
Figure 2-1: ATA-Flash Drive functional block diagram
4
© 2011 Apacer Technology Inc.
Rev. 1.4
Ⅲ
Value Added ATA Flash Drive
AP-FD25A2xAxxxxxR-XXX
3. Pin Assignments
Table 3-1 lists the pin assignments with respective signal names for the 44-pin configuration. A “#” suffix
indicates the active low signal. The pin type can be input, output or input/output.
Figure 3-1: ATA-Flash Drive 44-pin Connector
Pin 43
Pin 1
Table 3-1: Pin assignments for the 44-pin configuration
Pin No.
Signal Name
Pin Type
I/O Type
Pin No.
Signal Name
Pin Type
I/O Type
1
3
5
7
9
11
13
15
17
19
21
23
RESET#
D7
I
I2U
2
4
6
8
10
12
14
16
18
20
22
24
GND
D8
D9
D10
D11
D12
D13
D14
D15
NC
-
Ground
I1Z, O2
I1Z, O2
I1Z, O2
I1Z, O2
I1Z, O2
I1Z, O2
I1Z, O2
I1Z, O2
-
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
-
I1Z, O2
I1Z, O2
I1Z, O2
I1Z, O2
I1Z, O2
I1Z, O2
I1Z, O2
I1Z, O2
Ground
O1
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
-
D6
D5
D4
D3
D2
D1
D0
GND
DMARQ
IOWR#
IORD#
HDMARDY#
HSTROBE#
IORDY
DDMARDY#
DSTROBE
DMACK#
INTRQ
A1
O
I
GND
GND
Ground
Ground
I2Z
-
-
25
27
I
I2Z
O1
26
28
GND
Ground
I1U
O
CSEL
I
29
31
33
35
37
39
41
I
O
I
I
I
I2U-
O1
I1Z
I1Z
I2Z
30
32
34
36
38
40
42
GND
IOCS16#
PDIAG#
A2
CS3FX#
GND
-
O
I/O
I
I
-
-
O2
I1U, O1
I1Z
I2Z
Ground
Power
A0
CS1FX#
DASP#
VDD
I/O
-
I1U, O6
Power
VDD
-
43
GND
-
Ground
44
NC
-
-
5
© 2011 Apacer Technology Inc.
Rev. 1.4
Ⅲ
Value Added ATA Flash Drive
AP-FD25A2xAxxxxxR-XXX
4. Capacity Specification
Capacity specification of the ATA-Flash Drive (AFD) product family is available as shown in Table 4-1. It
lists the specific capacity and the default numbers of heads, sectors and cylinders for each product line.
Table 4-1: AFD capacity specifications
Capacity
256 MB
512 MB
1GB
Total bytes
256,901,120
Cylinders
980
Heads
16
Sectors
32
Max LBA
501,760
512,483,328
993
16
63
1,000,944
2,001,888
4,000,752
8,000,496
15,628,032
31,252,032
62,502,048
125,004,096
1,024,966,656
2,048,385,024
4,096,253,952
8,001,552,384
16,001,040,384
32,001,048,576
64,002,097,152
1986
16
63
2GB
3969
16
63
4GB
7937
16
63
8GB
15504
16383*
16383*
16383*
16
63
16 GB
32 GB
64 GB
16
63
16
63
16
63
*Cylinders, heads or sectors are not applicable for these capacities. Only LBA addressing applies.
4.1 Performance Specification
Performance of the ATA-Flash Drive is listed in Table 4-2.
Table 4-2: Performance specifications
Capacity
256 MB / 512 MB
/ 1GB / 2GB / 4GB
64 GB
8 GB
16 GB
32 GB
Performance
Sustained read (MB/s)
Sustained write (MB/s)
25
7
35
10
35
15
35
20
20
10
Note: Above figures measured based on flash configurations.
4.2 Environmental Specifications
Environmental specification of the ATA-Flash Drive which follows the MIL-STD-810F standards is
available as shown in Table 4-3.
Table 4-3: ATA-Flash Drive environmental specifications
Environment
Specification
0°C to 70°C; -40°C to 85°C (Ext. Temp.)
Operation
Storage
Temperature
Humidity
-40°C to 100°C
5% to 95% RH (Non-condensing)
Vibration (Non-Operation)
Shock (Non-Operation)
Sine wave: 10~2000Hz, 15G (X, Y, Z axes)
Half sine wave, Peak acceleration 50 G, 11 ms (X, Y, Z ; All 6 axes)
6
© 2011 Apacer Technology Inc.
Rev. 1.4
Ⅲ
Value Added ATA Flash Drive
AP-FD25A2xAxxxxxR-XXX
5. Flash Management
5.1 Intelligent Endurance Design
5.1.1 Advanced wear-leveling algorithms
The NAND flash devices are limited by a certain number of write cycles. When using a file system,
frequent file table updates is mandatory. If some area on the flash wears out faster than others, it would
significantly reduce the lifetime of the whole device, even if the erase counts of others are far from the
write cycle limit. Thus, if the write cycles can be distributed evenly across the media, the lifetime of the
media can be prolonged significantly. The scheme is achieved both via buffer management and Apacer-
specific advanced wear leveling to ensure that the lifetime of the flash media can be increased, and the
disk access performance is optimized as well.
5.1.2 S.M.A.R.T. technology
S.M.A.R.T. is an acronym for Self-Monitoring, Analysis and Reporting Technology, an open standard
allowing disk drives to automatically monitor their own health and report potential problems. It protects the
user from unscheduled downtime by monitoring and storing critical drive performance and calibration
parameters. Ideally, this should allow taking proactive actions to prevent impending drive failure. Apacer
SMART feature adopts the standard SMART command B0h to read data from the drive. When the Apacer
SMART Utility running on the host, it analyzes and reports the disk status to the host before the device is
in critical condition.
5.1.3 Built-in hardware ECC
The ATA-Flash Drive uses BCH Error Detection Code (EDC) and Error Correction Code (ECC) algorithms
which correct up to eight random single-bit errors for each 512-byte block of data. High performance is
fulfilled through hardware-based error detection and correction.
5.1.4 Enhanced data integrity
The properties of NAND flash memory make it ideal for applications that require high integrity while
operating in challenging environments. The integrity of data to NAND flash memory is generally
maintained through ECC algorithms and bad block management. Flash controllers can support up to 8
bits ECC capability for accuracy of data transactions, and bad block management is a preventive
mechanism from loss of data by retiring unusable media blocks and relocating the data to the other blocks,
along with the integration of advanced wear leveling algorithms, so that the lifespan of device can be
expanded.
7
© 2011 Apacer Technology Inc.
Rev. 1.4
Ⅲ
Value Added ATA Flash Drive
AP-FD25A2xAxxxxxR-XXX
5.2 Intelligent Power Failure Recovery
The Low Power Detection on the controller initiates cached data saving before the power supply to the
device is too low. This feature prevents the device from crash and ensures data integrity during an
unexpected blackout. Once power was failure before cached data writing back into flash, data in the
cache will lost. The next time the power is on, the controller will check these fragmented data segment,
and, if necessary, replace them with old data kept in flash until programmed successfully.
5.3 Enhanced Security Level
5.3.1 Secure protection zone
Partitioning with static commands to logically secure data, protection zones are the solid frameworks of
file vaults. 3 different types of zones, unprotected, read-only, and restricted, are offered for effortless
administration. When the product is shipped out of Apacer, all sectors are in the unprotected zone, which
means there is no control on any data transaction. For further management control, the read-only zone
can be set to be accessed exclusively for grantees, and the restricted zone, to be as the maximum
security stockade with full administration privilege required. A maximum of 4 zones can be configured as
either restricted or read-only zone presenting concurrently. The space outside these 4 zones is
automatically in the unprotected zone if available. After the zone has been configured, the protection zone
can be de-activated or re-activated by either software methods or hardware components. Protection zone
configuration is non-volatile and it will be in effect until the next set of configuration overwrites it.
5.3.2 ATA Secure Erase
Accomplished by the Secure Erase (SE) command, which added to the open ANSI standards that control
disk drives, “ATA Secure Erase” is built into the disk drive itself and thus far less susceptible to malicious
software attacks than external software utilities. It is a positive easy-to-use data destroy command,
amounting to electronic data shredding. Executing the command causes a drive to internally completely
erase all possible user data. This command is carried out within disk drives, so no additional software is
required. Once executed, neither data nor the erase counter on the device would be recoverable, which
blurs the accuracy of device lifespan. The process to erase will not be stopped until finished while
encountering power failure, and will be continued when power is back on.
8
© 2011 Apacer Technology Inc.
Rev. 1.4
Ⅲ
Value Added ATA Flash Drive
AP-FD25A2xAxxxxxR-XXX
6. Software Interface
6.1 Command Set
This section defines the software requirements and the format of the commands the host sends to the
ATA-Flash Drive (AFD). Commands are issued to the AFD by loading the required registers in the
command block with the supplied parameters, and then writing the command code to the command
register. The manner in which a command is accepted varies.
Table 6-1: Command set (1 of 2)
Command
Check-Power-Mode
Code
E5H or 98H
90H
FR1
SC2
-
SN3
-
CY4
-
DH5
D8
D
Y
LBA6
-
-
-
-
Execute-Drive-Diagnostic
Erase Sector(s)
Flush-Cache
-
-
-
C0H
-
Y
-
Y7
Y
-
Y
-
Y
-
E7H
-
D
Y8
D
D
D
Y
Format Track
50H
-
-
Y
-
Y
-
Identify-Drive
ECH
-
-
-
Idle
E3H or 97H
E1H or 95H
91H
-
Y
-
-
-
-
Idle-Immediate
Initialize-Drive-Parameters
NOP
-
-
-
-
-
Y
-
-
-
-
00H
-
-
-
D
D
Y
-
Read-Buffer
E4H
-
-
-
-
-
Read-DMA
C8H or C9H
C4H
-
Y
Y
Y
Y
-
Y
Y
Y
Y
-
Y
Y
Y
Y
-
Y
Y
Y
Y
-
Read-Multiple
-
Y
Read-Sector(s)
Read-Verify-Sector(s)
Recalibrate
20H or 21H
40H or 41H
1XH
-
Y
-
Y
-
D
D
D
D
D
D
D
D
Y
Request-Sense
Security-Disable-Password
Security-Erase-Prepare
Security-Erase-Unit
Security-Freeze-Lock
Security-Set-Password
Security-Unlock
Seek
03H
-
-
-
-
-
F6H
-
-
-
-
-
F3H
-
-
-
-
-
F4H
-
-
-
-
-
F5H
-
-
-
-
-
F1H
-
-
-
-
-
F2H
-
-
-
-
-
7XH
-
-
Y
-
Y
-
Y
-
Set-Features
EFH
Y7
-
D
9
© 2011 Apacer Technology Inc.
Rev. 1.4
Ⅲ
Value Added ATA Flash Drive
AP-FD25A2xAxxxxxR-XXX
Table 6-1: Command set (2 of 2)
Command
Code
B0H
FR1
SC2
Y
Y
-
SN3
Y
-
CY4
Y
-
DH5
D
D
D
D
D
Y
LBA6
SMART
Y
-
-
-
-
-
-
-
-
-
-
-
-
Set-Multiple-Mode
Set-Sleep-Mode
Standby
C6H
-
-
E6H or 99H
E2H or 96H
E0H or 94H
87H
-
-
-
-
-
-
Standby-lmmediate
Translate-Sector
Write-Buffer
-
-
-
-
Y
-
Y
-
Y
-
Y
-
E8H
D
Y
Write-DMA
CAH or CBH
C5H
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Write-Multiple
Y
Write-Multiple-Without-Erase
Write-Sector(s)
Write-Sector-Without-Erase
Write-Verify
CDH
Y
30H or 31H
38H
Y
Y
3CH
Y
1. FR - Features register
2. SC - Sector Count register
3. SN - Sector Number register
4. CY - Cylinder registers
5. DH - Drive/Head register
6. LBA - Logical Block Address mode supported (see command descriptions for use)
7. Y - The register contains a valid parameter for this command
8. For the Drive/Head register:
Y means both the ATA-Flash Drive and Head parameters are used
D means only the ATA-Flash Drive parameter is valid and not the Head parameter
10
© 2011 Apacer Technology Inc.
Rev. 1.4
Ⅲ
Value Added ATA Flash Drive
AP-FD25A2xAxxxxxR-XXX
7. Electrical Specification
Caution: Absolute Maximum Stress Ratings – Applied conditions greater than those listed under
“Absolute Maximum Stress Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these conditions or conditions greater than those defined in
the operational sections of this data sheet is not implied. Exposure to absolute maximum stress rating
conditions may affect device reliability.
Table 7-1: ATA-Flash Drive operating voltage
Range
Ambient Temperature
0°C to 70°C
5V
Standard
4.5-5.5V
Extended Temperature
-40°C to 85°C
Table 7-2: Absolute maximum power pin stress ratings
Parameter
Symbol
VDD
Conditions
Input Power
-0.3V min. to 6.5V max.
-0.5V min. to VDD + 0.5V max.
Voltage on any pin except VDD with respect to GND
V
Table 7-3: Recommended system power-up timing
Symbol
Parameter
Typical
200
Maximum
Units
ms
1
TPU-READY
Power-up to Ready Operation
Power-up to Write Operation
1000
1000
1
TPU-WRITE
200
ms
1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter.
8. Physical Characteristics
11
© 2011 Apacer Technology Inc.
Rev. 1.4
Ⅲ
Value Added ATA Flash Drive
AP-FD25A2xAxxxxxR-XXX
Unit: mm
Tolerance: ± 0.2
12
© 2011 Apacer Technology Inc.
Rev. 1.4
Ⅲ
Value Added ATA Flash Drive
AP-FD25A2xAxxxxxR-XXX
Unit: mm
Tolerance: ± 0.2
13
© 2011 Apacer Technology Inc.
Rev. 1.4
Ⅲ
Value Added ATA Flash Drive
AP-FD25A2xAxxxxxR-XXX
9. Product Ordering Information
9.1 Product Code Designations
AP – FD25 A 2 X A xxxxx R – X X X
Temperature:
Blank: Standard
W: Extended Temperature
Flash Type
FW Version
RoHS Compliant
Capacity:
00256: 256MB
00512: 512MB
0001G: 1GB
0002G: 2GB
0004G: 4GB
0008G: 8GB
0016G: 16GB
0032G: 32GB
0064G: 64GB
Product Type
PCB Version
Controller Type
Outline
180D
2.5 inch ATA Flash Drive
Apacer Product Code
14
© 2011 Apacer Technology Inc.
Rev. 1.4
Ⅲ
Value Added ATA Flash Drive
AP-FD25A2xAxxxxxR-XXX
9.2 Valid Combinations
Capacity
256MB
512MB
1GB
Standard
Extended Temperature
AP-FD25A20A00256R-KS
AP-FD25A20A00512R-KS
AP-FD25A20A0001GR-KS
AP-FD25A20A0002GR-KS
AP-FD25A20A0004GR-KS
AP-FD25A20A0008GR-KS
AP-FD25A20A0016GR-KS
AP-FD25A20A0032GR-KS
AP-FD25A21A0064GR-KT
AP-FD25A20A00256R-KSW
AP-FD25A20A00512R-KSW
AP-FD25A20A0001GR-KSW
AP-FD25A20A0002GR-KSW
AP-FD25A20A0004GR-KSW
AP-FD25A20A0008GR-KSW
AP-FD25A20A0016GR-KSW
AP-FD25A20A0032GR-KSW
AP-FD25A21A0064GR-KTW
2GB
4GB
8GB
16GB
32GB
64GB
15
© 2011 Apacer Technology Inc.
Rev. 1.4
Ⅲ
Value Added ATA Flash Drive
AP-FD25A2xAxxxxxR-XXX
Revision History
Revision
1.0
Date
Description
Remark
02/03/2009
02/11/2009
08/11/2009
09/09/2009
Official release
1.1
Modified document layout
Combined all capacities collectively
Context refined
1.2
1.3
Updated Performance Specification &
Product Ordering Information
1.4
03/18/2011
16
© 2011 Apacer Technology Inc.
Rev. 1.4
Ⅲ
Value Added ATA Flash Drive
AP-FD25A2xAxxxxxR-XXX
Global Presence
Apacer Technology Inc.
4th Fl., 75 Hsin Tai Wu Rd., Sec.1
Hsichih, 221 Taipei Hsien
Taiwan, R.O.C.
Taiwan (Headquarters)
Tel: +886-2-2698-2888
Fax: +886-2-2698-2889
amtsales@apacer.com
Apacer Memory America, Inc.
386 Fairview Way, Suite102,
Milpitas, CA 95035
Tel: 1-408-586-1291
Fax: 1-408-935-9611
U.S.A.
Japan
Europe
sa@apacerus.com
Apacer Technology Corp.
5F, Matsura Bldg., Shiba, Minato-Ku
Tokyo, 105-0014, Japan
Tel: 81-3-5419-2668
Fax: 81-3-5419-0018
jpservices@apacer.com
Apacer Technology B.V.
Europalaan 89
5232 BC 'S-Hertogenbosch
The Netherlands
Tel: 31-73-645-9620
Fax: 31-73-645-9629
sales@apacer.nl
Apacer Electronic (Shanghai) Co., Ltd
1301, No.251,Xiaomuqiao Road, Shanghai,
200032, China
Tel: 86-21-5529-0222
Fax: 86-21-5206-6939
China
India
sales@apacer.com.cn
Apacer Technologies Pvt. Ltd.
#143, 1st Floor, Raheja Arcade,
5th Block Kormangala Industrial Layout,
Bangalore - 560095, India
Tel: 91-80-4152-9061
sales_india@apacer.com
17
© 2011 Apacer Technology Inc.
Rev. 1.4
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Apacer:
AP-FD25A20A0002GR-KS AP-FD25A20A0004GR-KS AP-FD25A20A0004GR-KSW AP-FD25A20A0008GR-KS AP-
FD25A20A0032GR-KSW AP-FD25A20A00512R-KS AP-FD25A20A00512R-KSW AP-FM016GE11S5R-KS AP-
FM016GE11S5R-KSW
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明