BU-61845G4-100 [ETC]
Telecommunication IC ; 电信IC\n型号: | BU-61845G4-100 |
厂家: | ETC |
描述: | Telecommunication IC
|
文件: | 总56页 (文件大小:304K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
BU-6174X/6184X/6186X
ENHANCED MINIATURE ADVANCED
COMMUNICATIONS ENGINE
(ENHANCED MINI-ACE)
FEATURES
DESCRIPTION
FULLY INTEGRATED 1553A/B NOTICE 2,
MCAIR, STANAG 3838 INTERFACE TERMINAL
•
The Enhanced Mini-ACE family of a set of 20 instructions.This provides
MIL-STD-1553 terminals provide an autonomous means of imple-
complete interfaces between a host menting
processor and a 1553 bus. These scheduling, message retry schemes,
terminals integrate dual transceiver, data double buffering, asynchronous
protocol logic, and 4K words or 64K message insertion, and reporting to
COMPATIBLE WITH MINI-ACE (PLUS)
AND ACE GENERATIONS
•
•
multi-frame
message
CHOICE OF :
RT OR BC/RT/MT IN SAME FOOTPRINT
RT OR BC/RT/MT WITH 4K RAM
BC/RT/MT WITH 64K RAM, WITH RAM PARITY
•
•
words of RAM.
the host CPU. The Enhanced
Mini-ACE incorporates fully
•
a
CHOICE OF 5V OR 3.3V LOGIC
•
•
With a 1.0 inch square package, the autonomous built-in self-test, which
Enhanced Mini-ACE is nearly 100% provides comprehensive testing of
footprint and software compatibile the internal protocol logic and/or
with the previous generation Mini- RAM.
ACE (Plus) terminals, and is soft-
ware compatibile with the older ACE The Enhanced Mini-ACE RT offers
5V TRANSCEIVER WITH 1760 AND
MCAIR COMPATIBLE OPTIONS
COMPREHENSIVE BUILT-IN SELF-TEST
•
•
FLEXIBLE PROCESSOR/MEMORY
INTERFACE, WITH REDUCED HOST WAIT TIME
series.
the same choices of subaddress
buffering as the ACE and Mini-ACE
CHOICE OF 10, 12, 16, OR 20 MHZ CLOCK
•
•
The Enhanced Mini-ACE is powered (Plus), along with a global circular
by a choice 5V, or 5V/3.3V (3.3V buffering option, 50% rollover inter-
logic). Multiprotocol support of rupt for circular buffers, an interrupt
MIL-STD-1553A/B and STANAG status queue, and an "Auto-boot"
3838, including versions incorporat- option to support MIL-STD-1760.
ing McAir compatible transmitters, is
provided. There is a choice of 10, 12, The Enhanced Mini-ACE terminals
16, or 20 Mhz clocks. The BC/RT/MT provide the same flexibility in host
versions with 64K words of RAM interface configurations as the
HIGHLY AUTONOMOUS BC WITH
BUILT-IN MESSAGE SEQUENCE CONTROL:
FRAME SCHEDULING
•
BRANCHING
•
ASYNCHRONOUS MESSAGE INSERTION
GENEERAL PURPOSE QUEUE
USER-DEFINED INTERRUPTS
•
•
•
ADVANCED RT FUNCTIONS
•
GLOBAL CIRCULAR BUFFERING
INTERRUPT STATUS QUEUE
50% CIRCULAR BUFFER ROLLOVER
•
•
include built-in RAM parity checking.
ACE/Mini-ACE, along with a reduc-
tion in the host processor's worst
•
BC features include a built-in mes- case holdoff time.
sage sequence control engine, with
INTERRPTS
TX/RX_A
SHARED
RAM
*
TRANSCEIVER
A
CH. A
DATA
BUFFERS
PROCESSOR
D15-D0
DATA BUS
DATA BUS
TX/RX_A
TX/RX_B
DUAL
ENCODER/DECODER,
MULTIPROTOCOL
AND
MEMORY
MANAGEMENT
ADDRESS
BUFFERS
PROCESSOR
ADDRESS BUS
ADDRESS BUS
A15-A0
TRANSCEIVER
B
CH. B
TX/RX_B
TRANSPARENT/BUFFERED, STRBD, SELECT,
RD/WR, MEM/REG, TRIGGER_SEL/MEMENA-IN,
MSB/LSB/DTGRT
PROCESSOR
AND
MEMORY
INTERFACE
LOGIC
PROCESSOR
AND
MEMORY
CONTROL
RT ADDRESS
RTAD4-RTAD0, RTADP
INCMD
IOEN, READYD
ADDR_LAT/MEMOE, ZERO_WAIT/MEMWR,
8/16-BIT/DTREQ, POLARITY_SEL/DTACK
INT
INTERRUPT
REQUEST
CLK_IN, TAG_CLK,
MSTCLR,SSFLAG/EXT_TRG
MISCELLANEOUS
* SEE ORDERING INFORMATION FOR AVAILABLE MEMORY
FIGURE 1. ENHANCED MINI-ACE BLOCK DIAGRAM
2000 Data Device Corporation
©
TABLE 1. EHANCED MINI-ACE SERIES SPECIFICATIONS
TABLE 1. EHANCED MINI-ACE SERIES SPECIFICATIONS (Cont’d)
PARAMETER
MIN
TYP
MAX
UNITS
PARAMETER
MIN TYP MAX UNITS
ABSOLUTE MAXIMUM RATING
Supply Voltage
POWER SUPPLY REQUIREMENTS
Voltages/Tolerances
! Logic +5V or +3.3V
! RAM +5V
! Transceiver +5V (Note 11)
Logic
! Voltage Input Range for +5V
Logic (BU-61XX5)
! Voltage Input Range for +3.3V
Logic (BU-61XX3/4)
-0.3
-0.3
-0.3
6.0
6.0
7.0
V
V
V
! +5V (RAM for 61864(5),
Logic for BU-61XX5) (Note 11)
! +3.3V (Logic for BU-61XX3/4)
(Note 11)
4.5
3.0
5.0
3.3
5.0
5.5
3.6
5.5
V
V
V
-0.3
-0.3
6.0
6.0
V
V
! +5V (Ch. A, Ch. B)
4.75
Current Drain (Total Hybrid)
! BU-61865XX-XX0
+5V (Logic, RAM, Ch. A, Ch. B)
• Idle
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
! BU-61865X3-XX2
+5V (Logic, RAM, Ch. A, Ch. B)
• Idle
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
! BU-61864XX-XX0
+5V (RAM, Ch. A, Ch. B)
• Idle
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
• 3.3V Logic
180
285
390
600
mA
mA
mA
mA
RECEIVER
Differential Input Resistance
(Notes 1-6)
Differential Input Capacitance
(Notes 1-6)
Threshold Voltage, Transformer
Coupled, Measured on Stub
Common Mode Voltage (Note 7)
2.5
kΩ
pF
5
0.200
0.860
10
Vp-p
Vpeak
180
296
412
645
mA
mA
mA
mA
TRANSMITTER
Differential Output Voltage
! Direct Coupled Across 35 Ω,
Measured on Bus
! Transformer Coupled Across
70 Ω, Measured on Bus
(BU-61XXXXX-XX0,
BU-61XXXXX-XX2) (Note 13)
Output Noise, Differential (Direct
Coupled)
6
7
9
Vp-p
120
225
330
540
40
mA
mA
mA
mA
mA
18
20
20
22
27
27
10
Vp-p
Vp-p
MVP-P
! BU-61864X3-XX2
+5V (RAM, Ch. A, Ch. B)
• Idle
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
• 3.3V Logic
! BU-61745XX-XX0. BU-61845XX-XX0
+5V (Logic, RAM, Ch. A, Ch. B)
• Idle
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
! BU-61745X3-XX2. BU-61845X3-XX2
+5V (Logic, RAM, Ch. A, Ch. B)
• Idle
-250
250
mVpeak
Output Offset Voltage, Transformer
Coupled Across 70 ohms
Rise/Fall Time
120
236
352
585
40
mA
mA
mA
mA
mA
100
200
150
250
300
300
nsec
nsec
(BU-61XXXX3,
BU-61XXXX4)
LOGIC
VIH
All signals except CLK_IN
CLK_IN
VIL
All signals except CLK_IN
CLK_IN
Schmidt Hysteresis
All signals except CLK_IN
CLK_IN
2.1
0.8•Vcc
V
V
160
265
370
580
mA
mA
mA
mA
0.7
0.2•Vcc
V
V
0.4
1.0
V
V
160
276
392
625
mA
mA
mA
mA
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
! BU-61743XX-XX0, BU-61843XX-XX0
+5V (Ch. A, Ch. B)
IIH, IIL
All signals except CLK_IN
IIH (Vcc=5.5V, VIN=Vcc)
IIH (Vcc=5.5V, VIN=2.7V)
IIL (Vcc=3.6V, VIN=Vcc)
IIH (Vcc=3.6V, VIH=2.7V)
IIL (Vcc=5.5V, VIH=0.4V)
IIL (Vcc=3.6V, VIH=0.4V)
CLK_IN
-10
-350
-10
-350
-350
-350
10
-50
10
-33
-50
-33
µA
µA
µA
µA
µA
µA
100
205
310
520
40
mA
mA
mA
mA
mA
mA
• Idle
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
• 3.3V Logic
! BU-61743X3-XX2, BU-61843X3-XX2
+5V (Ch. A, Ch. B)
IIH
IIL
-10
-10
2.4
10
10
µA
µA
V
VOH (Vcc=4.5V, VIH=2.7V,
VIL=0.2V, IOH=max)
VOH (Vcc=3.0V, VIH=2.7V,
VIL=0.2V, IOH=max)
VOL (Vcc=4.5V, VIH=2.7V,
VIL=0.2V, IOL=max)
VOL (Vcc=3.0V, VIH=2.7V,
VIL=0.2V, IOL=max)
IOL
100
216
332
565
40
mA
mA
mA
mA
mA
• Idle
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
• 3.3V Logic
2.4
V
V
V
0.4
0.4
3.4
mA
mA
pF
IOH
-3.4
50
50
CI (Input Capacitance)
CIO (Bi-directional signal input
capacitance)
pF
2
TABLE 1. EHANCED MINI-ACE SERIES SPECIFICATIONS (Cont’d)
TABLE 1. EHANCED MINI-ACE SERIES SPECIFICATIONS (Cont’d)
PARAMETER MIN TYP MAX UNITS
CLOCK INPUT
PARAMETER
MIN TYP MAX UNITS
POWER DISSIPATION (Note 14)
Total Hybrid
Frequency
! BU-61865XX-XX0
• Idle
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
! BU-61865X3-XX2
! Nominal Value
• Default Mode
• Option
• Option
• Option
! Long Term Tolerance
• 1553A Compliance
• 1553B Compliance
! Short Term Tolerance, 1 second
• 1553A Compliance
• 1553B Compliance
! Duty Cycle
0.99
1.22
1.45
1.90
W
W
W
W
16.0
12.0
10.0
20.0
MHz
MHz
MHz
MHz
• Idle
0.99
1.28
1.58
2.16
W
W
W
W
-0.01
-0.10
0.01
0.1
%
%
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
! BU-61864XX-XX0
0.001
-0.01
40
0.001
0.01
60
%
%
%
• Idle
0.80
1.03
1.26
1.71
W
W
W
W
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
! BU-61864X3-XX2
1553 MESSAGE TIMING
Completion of CPU Write
2.5
9.5
µs
µs
µs
(BC Start)-to-Start of Next Message
for (Non-enhanced BC Mode)
BC Intermessage Gap (Note 8)
Non-enhanced
(Mini-ACE compatible) BC mode
Enhanced BC mode (Note 9)
• Idle
0.80
1.09
1.39
1.97
W
W
W
W
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
! BU-61745XX-XX0, BU-61845XX-XX0
• Idle
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
! BU-61745X3-XX2, BU-61845X3-XX2
• Idle
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
! BU-61743XX-XX0, BU-61843XX-XX0
• Idle
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
! BU-61743X3-XX2, BU-61843X3-XX2
• Idle
10.0
to
10.5
0.88
1.11
1.33
1.79
W
W
W
W
BC/RT/MT Response Timeout (Note 10)
! 18.5 nominal
! 22.5 nominal
! 50.5 nominal
! 128.0 nominal
RT Response Time
(mid-parity to mid-sync) (Note 11)
Transmitter Watchdog Timeout
17.5 18.5 19.5
21.5 22.5 23.5
49.5 50.5 51.5
127 129.5 131
µs
µs
µs
µs
µs
0.88
1.17
1.46
2.05
W
W
W
W
4
7
660.5
µs
THERMAL
Thermal Resistance, Junction-to-Case,
Hottest Die (θJC)
Operating Junction Temperature
Storage Temperature
Lead Temperature (soldering, 10 sec.)
0.69
0.92
1.15
1.60
W
W
W
W
20
150
150
+300
°C/W
°C
°C
-55
-65
°C
0.69
0.98
1.28
1.86
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
Hottest Die
W
W
W
W
PHYSICAL CHARACTERISTICS
Size
1.0 X 1.0 X 0.155
in.
(25.4 x 25.4 x 3.94) (mm)
! BU-61XXXXX-XX0
• Idle
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
! BU-61XXXX3-XX2
Weight
0.28
0.51
0.75
1.22
W
W
W
W
0.6
oz
(17)
(g)
NOTES:
• Idle
0.28
0.58
0.88
1.48
W
W
W
W
Notes 1 through 6 are applicable to the Receiver Differential
Resistance and Differential Capacitance specifications:
• 25% Transmitter Duty Cycle
• 50% Transmitter Duty Cycle
• 100% Transmitter Duty Cycle
(1) Specifications include both transmitter and receiver (tied together
internally).
(2) Impedance parameters are specified directly between pins TX/RX
TX/RX A(B)
A(B) and
of the Enhanced Mini-ACE hybrid.
(3) It is assumed that all power and ground inputs to the hybrid are
connected.
(4) The specifications are applicable for both unpowered and powered
conditions.
3
INTRODUCTION
(5) The specifications assume a 2 volt rms balanced, differential, sinu-
soidal input. The applicable frequency range is 75 kHz to 1 MHz.
The BU-61743/61745 RT, and BU-61843/61845/61864/61865
BC/RT/MT Enhanced Mini-ACE family of MIL-STD-1553 termi-
nals comprise a complete integrated interface between a host
processor and a MIL-STD-1553 bus. All members of the
Enhanced Mini-ACE family are packaged in the same 1.0 square
inch flatpack package. The Enhanced Mini-ACE hybrids are
nearly 100% footprint and software compatible with the previous
generation Mini-ACE and Mini-ACE Plus terminals, and are soft-
ware compatibility with the original ACE series.
(6) Minimum resistance and maximum capacitance parameters are
guaranteed over the operating range, but are not tested.
(7) Assumes a common mode voltage within the frequency range of dc
to 2 MHz, applied to pins of the isolation transformer on the stub
side (either direct or transformer coupled), and referenced to hybrid
ground. Transformer must be a DDC recommended transformer or
other transformer that provides an equivalent minimum CMRR.
The Enhanced Mini-ACE provides complete multiprotocol sup-
port of MIL-STD-1553A/B/McAir and STANAG 3838. All versions
integrate dual transceiver; along with protocol, host interface,
memory management logic; and a minimum of 4K words of
RAM. In addition, the BU-61864 and BU-61865 BC/RT/MT ter-
minals include 64K words of internal RAM, with built-in parity
checking.
(8) Typical value for minimum intermessage gap time. Under software
control, this may be lengthened to 65,535 ms - message time, in
increments of 1 µs. If ENHANCED CPU ACCESS, bit 14 of
Configuration Register #6, is set to logic "1", then host accesses
during BC Start-of-Message (SOM) and End-of-Message (EOM)
transfer sequences could have the effect of lengthening the inter-
message gap time. For each host access during an SOM or EOM
sequence, the intermessage gap time will be lengthened by 6 clock
cycles. Since there are 7 internal transfers during SOM, and 5 dur-
ing EOM, this could theoretically lengthen the intermessage gap by
up to 72 clock cycles; i.e., up to 7.2 ms with a 10 MHz clock, 6.0 µs
with a 12 MHz clock, 4.5 µs with a 16 MHz clock, or 3.6 µs with a
20 MHz clock.
The Enhanced Mini-ACEs include a 5V, voltage source trans-
ceiver for improved line driving capability, with options for MIL-
STD-1760 and McAir compatibility. As a means of reducing
power consumption, there are versions for which the logic is
powered by 3.3V, rather than 5V. To provide further flexibility, the
Enhanced Mini-ACE may operate with a choice of 10, 12, 16, or
20 MHz clock inputs.
(9) For Enhanced BC mode, the typical value for intermessage gap
time is approximately 10 clock cycles longer than for the non-
enhanced BC mode. That is, an addition of 1.0 µs at 10 MHz, 833
ns at 12 MHz, 625 ns at 16 MHz, or 500 ns at 20 MHz.
One of the new salient features of the Enhanced Mini-ACE is its
Enhanced bus controller architecture. The Enhanced BC's high-
ly autonomous message sequence control engine provides a
means for offloading the host processor for implementing multi-
frame message scheduling, message retry schemes, data dou-
ble buffering, and asynchronous message insertion. For the pur-
pose of performing messaging to the host processor, the
Enhanced BC mode includes a General Purpose Queue, along
with user-defined interrupts.
(10) Software programmable (4 options). Includes RT-to-RT Timeout
(measured mid-parity of transmit Command Word to mid-sync of
transmitting RT Status Word).
(11) Measured from mid-parity crossing of Command Word to mid-sync
crossing of RT's Status Word.
A second major new feature of the Enhanced Mini-ACE is the
incorporation of a fully autonomous built-in self-test. This test
provides comprehensive testing of the internal protocol logic. A
separate test verifies the operation of the internal RAM. Since
the self-tests are fully autonomous, they eliminate the need for
the host to write and read stimulus and response vectors.
(12) External 10 µF Tantalum and 0.1 µF capacitors should be located
as close as possible to Pins 20 and 72, and a 0.1 µF at pin 37. For
BU-61864 and BU-61865, there should also be a 0.1 µF at pin 26.
(13) MIL-STD-1760 requires a 20 Vp-p minimum output on the stub con-
nection.
The Enhanced Mini-ACE RT offers the same choices of single,
double, and circular buffering for individual subaddresses as
ACE and Mini-ACE (Plus). New enhancements to the RT archi-
tecture include a global circular buffering option for multiple (or
all) receive subaddresses, a 50% rollover interrupt for circular
buffers, an interrupt status queue for logging up to 32 interrupt
events, and an option to automatically initialize to RT mode with
the Busy bit set. The interrupt status queue and 50% rollover
interrupt features are also included as improvements to the
Enhanced Mini-ACE's Monitor architecture.
(14) Power dissipation specifications assume a transformer coupled
configuration with external dissipation (while transmitting) of:
0.14 watts for the active isolation transformer,
0.80 watts for the active bus coupling transformer,
0.45 watts for each of the two bus isolation resistors and
0.15 watts for each of the two bus termination resistors.
To minimize board space and "glue" logic, the Enhanced Mini-
ACE terminals provide the same wide choice of host interface
configurations as the ACE and Mini-ACE (Plus). This includes
support of interfaces to 16-bit or 8-bit processors, memory or
4
port type interfaces, and multiplexed or non-multiplexed
address/data buses. In addition, with respect to ACE/Mini-ACE
(Plus), the worst case processor wait time has been significant-
ly reduced. For example, assuming a 16 MHz clock, this time has
been reduced from 2.8 µs to 632 ns for read accesses, and to
570 ns for write accesses.
INTERNAL REGISTERS
The address mapping for the Enhanced Mini-ACE registers is
illustrated in TABLE 2:
TABLE 2. ADDRESS MAPPING
REGISTER
ADDRESS LINES
DESCRIPTION/ACCESSIBILITY
The Enhanced Mini-ACE series terminals operate over the full
military temperature range of -55 to +125°C. Available screened
to MIL-PRF-38534C, the terminals are ideal for military and
industrial processor-to-1553 applications.
A4 A3 A2 A1 A0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
Interrupt Mask Register #1 (RD/WR)
Configuration Register #1 (RD/WR)
Configuration Register #2 (RD/WR)
Start/Reset Register (WR)
TRANSCEIVERS
The transceivers in the Enhanced Mini-ACE series terminals are
fully monolithic, requiring only a +5 volt power input. The trans-
mitters are voltage sources, which provide improved line driving
capability over current sources. This serves to improve perfor-
mance on long buses with many taps. The transmitters also offer
an option which satisfies the MIL-STD-1760 requirement for a
minimum of 20 volts peak-to-peak, transformer coupled output.
Non-Enhanced BC/RT Command Stack Pointer /
Enhanced BC Instruction List Pointer Register
(RD)
0
0
0
0
0
1
1
0
1
0
BC Control Word /
RT Subaddress Control Word Register (RD/WR)
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
0
0
0
0
0
1
1
0
0
1
1
1
0
1
0
1
0
1
Time Tag Register (RD/WR)
Interrupt Status Register #1 (RD)
Besides eliminating the demand for an additional power supply,
the use of a +5V-only transceiver requires the use of a step-up,
rather than a step-down, isolation transformer. This provides the
advantage of a higher terminal input impedance than is possible
for a 15 volt or 12 volt transmitter. As a result, there is a greater
margin for the input impedance test, mandated for the 1553 val-
idation test. This characteristic allows for longer cable lengths
between a system connector and the isolation transformers of an
embedded 1553 terminal.
Configuration Register #3 (RD/WR)
Configuration Register #4 (RD/WR)
Configuration Register #5 (RD/WR)
RT / Monitor Data Stack Address Register (RD)
BC Frame Time Remaining Register (RD)
BC Time Remaining to Next Message Register
(RD)
0
0
1
1
1
1
0
0
0
1
Non-Enhanced BC Frame Time / Enhanced BC
Initial Instruction Pointer / RT Last Command /
MT Trigger Word Register(RD/WR)
To provide compatibility to McAir specs, the Enhanced Mini-
ACEs are available with an option for transmitters with increased
rise and fall times.
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
0
1
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
1
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
1
0
1
0
RT Status Word Register (RD)
RT BIT Word Register (RD)
Test Mode Register 0
Additionally, for MIL-STD-1760 applications, the Enhanced Mini-
ACE provides an option for a minimum stub voltage level of 20
volts peak-to-peak, transformer coupled.
Test Mode Register 1
Test Mode Register 2
The receiver sections of the Enhanced Mini-ACE are fully com-
pliant with MIL-STD-1553B Notice 2 in terms of front end over-
voltage protection, threshold, common mode rejection, and word
error rate.
Test Mode Register 3
Test Mode Register 4
Test Mode Register 5
Test Mode Register 6
REGISTER AND MEMORY ADDRESSING
Test Mode Register 7
The software interface of the Enhanced Mini-ACE to the host
processor consists of 24 internal operational registers for normal
operation, an additional 24 test registers, plus 64K words of
shared memory address space. The Enhanced Mini-ACE's 4K X
16 or 64K X 17 internal RAM resides in this address space.
Configuration Register #6 (RD/WR)
Configuration Register #7 (RD/WR)
RESERVED
BC Condition Code Register (RD)
BC General Purpose Flag Register (WR)
BIT Test Status Register (RD)
Interrupt Mask Register #2 (RD/WR)
Interrupt Status Register #2 (RD)
For normal operation, the host processor only needs to access
the lower 32 register address locations (00-1F). The next 32
locations (20-3F) should be reserved, since many of these are
used for factory test.
BC General Purpose Queue Pointer /
RT-MT Interrupt Status Queue Pointer Register
(RD/WR)
1
1
1
1
1
5
TABLE 3. INTERRUPT MASK REGISTER #1
(READ/WRITE 00H)
BIT
DESCRIPTION
RESERVED
15(MSB)
14
13
12
11
10
9
RAM PARITY ERROR
BC/RT TRANSMITTER TIMEOUT
BC/RT COMMAND STACK ROLLOVER
MT COMMAND STACK ROLLOVER
MT DATA STACK ROLLOVER
HANDSHAKE FAIL
8
BC RETRY
7
RT ADDRESS PARITY ERROR
TIME TAG ROLLOVER
6
5
RT CIRCULAR BUFFER ROLLOVER
RT SUBADDRESS CONTROL WORD EOM
BC END OF FRAME
4
3
2
FORMAT ERROR
1
BC STATUS SET / RT MODE CODE / MT PATTERN TRIGGER
0(LSB) END OF MESSAGE
TABLE 4. CONFIGURATION REGISTER #1
(READ/WRITE 01H)
BC FUNCTION (Bits
11-0 Enhanced Mode Only)
RT WITHOUT ALTERNATE
STATUS
RT WITH ALTERNATE
STATUS (Enhanced Only) (Enhanced mode only bits 12-0)
MONITOR FUNCTION
BIT
15 (MSB) RT/BC-MT (logic 0)
(logic 1)
(logic 0)
(logic 1)
(logic o)
14
13
12
MT/BC-RT (logic 0)
(logic 0)
(logic 1)
CURRENT AREA B/A
MESSAGE STOP-ON-ERROR
CURRENT AREA B/A
CURRENT AREA A/B
CURRENT AREA B/A
MESSAGE MONITOR ENABLED
MESSAGE MONITOR ENABLED MESSAGE MONITOR
(MMT)
ENABLED
11
10
9
FRAME STOP-ON-ERROR
DYNAMIC BUS CONTROL
ACCEPTANCE
S10
TRIGGER WORD ENABLED
START-ON-TRIGGER
STATUS SET
STOP-ON-MESSAGE
BUSY
S09
S08
S07
STATUS SET
STOP-ON-FRAME
SERVICE REQUEST
SUBSYSTEM FLAG
STOP-ON-TRIGGER
8
7
6
5
FRAME AUTO-REPEAT
NOT USED
EXTERNAL TRIGGER ENABLED RTFLAG (Enhanced Mode Only) S06
EXTERNAL TRIGGER ENABLED
NOT USED
INTERNAL TRIGGER ENABLED NOT USED
S05
S04
INTERMESSAGE GAP TIMER
ENABLED
NOT USED
NOT USED
4
3
2
1
RETRY ENABLED
NOT USED
NOT USED
NOT USED
NOT USED
S03
S02
S01
S00
NOT USED
DOUBLED/SINGLE RETRY
BC ENABLED (Read Only)
NOT USED
MONITOR ENABLED(Read Only)
BC FRAME IN PROGRESS
(Read Only)
MONITOR TRIGGERED
(Read Only)
0 (LSB)
BC MESSAGE IN PROGRESS
(Read Only)
RT MESSAGE IN PROGRESS
(Enhanced mode only,Read Only) PROGRESS (Read Only)
RT MESSAGE IN
MONITOR ACTIVE
(Read Only)
6
TABLE 5. CONFIGURATION REGISTER #2
(READ/WRITE 02H)
TABLE 8. BC CONTROL WORD REGISTER
(READ/WRITE 04H)
BIT
DESCRIPTION
BIT
DESCRIPTION
RESERVED
ENHANCED INTERRUPTS
15(MSB)
15(MSB)
14
MESSAGE ERROR MASK
SERVICE REQUEST BIT MASK
BUSY BIT MASK
14
RAM PARITY ENABLE
13
13
BUSY LOOKUP TABLE ENABLE
RX SA DOUBLE BUFFER ENABLE
OVERWRITE INVALID DATA
12
12
11
SUBSYSTEM FLAG BIT MASK
TERMINAL FLAG BIT MASK
RESERVED BITS MASK
RETRY ENABLED
11
10
10
256-WORD BOUNDARY DISABLE
TIME TAG RESOLUTION 2
9
9
8
7
BUS CHANNEL A/B
8
TIME TAG RESOLUTION 1
6
OFF-LINE SELF-TEST
MASK BROADCAST BIT
EOM INTERRUPT ENABLE
1553A/B SELECT
7
TIME TAG RESOLUTION 0
5
6
CLEAR TIME TAG ON SYNCHRONIZE
LOAD TIME TAG ON SYNCHRONIZE
INTERRUPT STATUS AUTO CLEAR
LEVEL/PULSE* INTERRUPT REQUEST
CLEAR SERVICE REQUEST
4
5
3
4
2
MODE CODE FORMAT
BROADCAST FORMAT
RT-to-RT FORMAT
3
1
2
0(LSB)
1
ENHANCED RT MEMORY MANAGEMENT
SEPARATE BROADCAST DATA
0(LSB)
TABLE 9. RT SUBADDRESS CONTROL WORD
(READ/WRITE 04H)
TABLE 6. START/RESET REGISTER
(WRITE 03H)
BIT
DESCRIPTION
RX: DOUBLE BUFFER ENABLE
TX: EOM INT
BIT
DESCRIPTION
15(MSB)
RESERVED
15(MSB)
14
14
13
12
11
10
9
RESERVED
13
TX: CIRC BUF INT
RESERVED
12
TX: MEMORY MANAGEMENT 2 (MM2)
TX: MEMORY MANAGEMENT 1 (MM1)
TX: MEMORY MANAGEMENT 0 (MM0)
RX: EOM INT
RESERVED
11
CLEAR RT HALT
10
9
CLEAR SELF-TEST REGISTER
INITIATE RAM SELF-TEST
RESERVED
8
RX: CIRC BUF INT
7
RX: MEMORY MANAGEMENT 2 (MM2)
RX: MEMORY MANAGEMENT 1 (MM1)
RX: MEMORY MANAGEMENT 0 (MM0)
BCST: EOM INT
8
6
7
INITIATE PROTOCOL SELF-TEST
BC/MT STOP-ON-MESSAGE
BC STOP-ON-FRAME
TIME TAG TEST CLOCK
TIME TAG RESET
5
6
4
5
3
BCST: CIRC BUF INT
4
2
BCST:MEMORY MANAGEMENT 2 (MM2)
BCST: MEMORY MANAGEMENT 1 (MM1)
BCST: MEMORY MANAGEMENT 0 (MM0)
3
1
0(LSB)
2
INTERRUPT RESET
BC/MT START
1
0(LSB) RESET
TABLE 7. BC/RT COMMAND STACK POINTER REG.
(READ 03H)
TABLE 10. TIME TAG REGISTER
(READ/WRITE 05H)
BIT
DESCRIPTION
BIT
DESCRIPTION
COMMAND STACK POINTER 15
TIME TAG 15
15(MSB)
15(MSB)
•
•
•
•
•
•
•
•
•
•
•
•
0(LSB)
COMMAND STACK POINTER 0
0(LSB)
TIME TAG 0
7
TABLE 11. INTERRUPT STATUS REGISTER #1
(READ 06H)
TABLE 13. CONFIGURATION REGISTER #4
(READ/WRITE 08H)
BIT
DESCRIPTION
BIT
DESCRIPTION
MASTER INTERRUPT
EXTERNAL BIT WORD ENABLE
15(MSB)
15(MSB)
14
13
12
11
10
9
RAM PARITY ERROR
14
INHIBIT BIT WORD IF BUSY
MODE COMMAND OVERRIDE BUSY
EXPANDED BC CONTROL WORD ENABLE
BROADCAST MASK ENA/XOR
RETRY IF -A AND M.E.
TRANSMITTER TIMEOUT
BC/RT COMMAND STACK ROLLOVER
MT COMMAND STACK ROLLOVER
MT DATA STACK ROLLOVER
HANDSHAKE FAIL
13
12
11
10
9
RETRY IF STATUS SET
8
1ST RETRY ALT/SAME BUS
2ND RETRY ALT/SAME BUS
VALID M.E./NO DATA
8
BC RETRY
7
7
RT ADDRESS PARITY ERROR
TIME TAG ROLLOVER
6
6
5
VALID BUSY/NO DATA
5
RT CIRCULAR BUFFER ROLLOVER
RT SUBADDRESS CONTROL WORD EOM
BC END OF FRAME
4
MT TAG GAP OPTION
4
3
LATCH RT ADRRESS WITH CONFIG #5
TEST MODE 2
3
2
FORMAT ERROR
2
BC STATUS SET / RT MODE CODE /
MT PATTERN TRIGGER
1
TEST MODE 1
1
0(LSB)
TEST MODE 0
0(LSB)
END OF MESSAGE
TABLE 14. CONFIGURATION REGISTER #5
(READ/WRITE 09H)
TABLE 12. CONFIGURATION REGISTER #3
(READ/WRITE 07H)
BIT
DESCRIPTION
BIT
DESCRIPTION
ENHANCED MODE ENABLE
15(MSB)
15(MSB) 12 / 16 MHZ CLOCK SELECT
14
BC/RT COMMAND STACK SIZE 1
BC/RT COMMAND STACK SIZE 0
MT COMMAND STACK SIZE 1
MT COMMAND STACK SIZE 0
MT DATA STACk SIZE 2
14
SINGLE-ENDED SELECT
EXTERNAL TX INHIBIT A
EXTERNAL TX INHIBIT B
EXPANDED CROSSING ENABLED
RESPONSE TIMEOUT SELECT 1
RESPONSE TIMEOUT SELECT 0
GAP CHECK ENABLED
BROADCAST DISABLED
RT ADDRESS LATCH/TRANSPARENT
RT ADDRESS 4
13
13
12
12
11
11
10
10
9
MT DATA STACk SIZE 1
9
8
MT DATA STACk SIZE 0
8
7
ILLEGALIZATION DISABLED
OVERRIDE MODE T/R ERROR
ALTERNATE STATUS WORD ENABLE
ILLEGAL RX TRANSFER DISABLE
BUSY RX TRANSFER DISABLE
RTFAIL / RTFLAG WRAP ENABLE
1553A MODE CODES ENABLE
ENHANCED MODE CODE HANDLING
7
6
6
5
5
4
4
RT ADDRESS 3
3
3
RT ADDRESS 2
2
2
RT ADDRESS 1
1
1
RT ADDRESS 0
0(LSB)
0(LSB)
RT ADDRESS PARITY
TABLE 15. RT / MONITOR DATA STACK ADDRESS REGISTER
(READ/WRITE 0AH)
BIT
DESCRIPTION
RT / MONITOR DATA STACK ADDRESS 15
15(MSB)
•
•
•
•
•
•
0(LSB)
RT / MONITOR DATA STACK ADDRESS 0
8
TABLE 16. BC FRAME TIME REMAINING REGISTER
(READ/WRITE 0BH)
TABLE 20. RT BIT WORD REGISTER
(WRITE 0FH)
BIT
DESCRIPTION
BIT
DESCRIPTION
BC FRAME TIME REMAINING 15
TRANSMITTER TIMEOUT
15(MSB)
15(MSB)
14
LOOP TEST FAILURE B
•
•
13
LOOP TEST FAILURE A
•
•
12
HANDSHAKE FAILURE
•
•
11
TRANSMITTER SHUTDOWN B
TRANSMITTER SHUTDOWN A
TERMINAL FLAG INHIBITED
BIT TEST FAIL
0(LSB)
BC FRAME TIME REMAINING 0
10
Note: resolution = 100 µs per LSB
9
8
TABLE 17. BC MESSAGE TIME REMAINING REGISTER
(READ/WRITE 0CH)
7
HIGH WORD COUNT
6
LOW WORD COUNT
BIT
DESCRIPTION
BC MESSAGE TIME REMAINING 15
5
INCORRECT SYNC RECEIVED
PARITY / MANCHESTER ERROR RECEIVED
RT-to-RT GAP / SYNCH / ADDRESS ERROR
RT-to-RT NO RESPONSE ERROR
RT-to-RT 2ND COMMAND WORD ERROR
COMMAND WORD CONTENTS ERROR
15(MSB)
4
•
•
3
•
•
2
•
•
1
0(LSB)
BC MESSAGE TIME REMAINING 0
0(LSB)
Note: resolution = 1 µs per LSB
TABLE 21. CONFIGURATION REGISTER #6
(READ/WRITE 18H)
TABLE 18. BC FRAME TIME / RT LAST COMMAND /
MT TRIGGER REGISTER (READ/WRITE 0DH)
BIT
15(MSB)
14
DESCRIPTION
ENHANCED BUS CONTROLLER
ENHANCED CPU ACCESS
BIT
DESCRIPTION
BIT 15
15(MSB)
•
•
COMMAND STACK POINTER INCREMENT ON EOM
(RT, MT)
•
•
•
13
•
12
11
10
9
GLOBAL CIRCULAR BUFFER ENABLE
GLOBAL CIRCULAR BUFFER SIZE 2
GLOBAL CIRCULAR BUFFER SIZE 1
GLOBAL CIRCULAR BUFFER SIZE 0
0(LSB)
BIT 0
TABLE 19. RT STATUS WORD REGISTER
(READ/WRITE 0EH)
DISABLE INVALID MESSAGES TO INTERRUPT STATUS
QUEUE
8
7
BIT
DESCRIPTION
LOGIC “0”
15(MSB)
DISABLE VALID MESSAGES TO INTERRUPT STATUS
QUEUE
14
LOGIC “0”
6
INTERRUPT STATUS QUEUE ENABLE
RT ADDRESS SOURCE
ENHANCED MESSAGE MONITOR
RESERVED
13
LOGIC “0”
5
12
LOGIC “0”
4
11
LOGIC “0”
3
10
MESSAGE ERROR
INSTRUMENTATION
SERVICE REQUEST
RESERVED
9
2
64-WORD REGISTER SPACE
CLOCK SELECT 1
8
1
7
0(LSB)
CLOCK SELECT 0
6
RESERVED
5
RESERVED
4
BROADCAST COMMAND RECEIVED
BUSY
3
2
SUBSYSTEM FLAG
DYNAMIC BUS CONTROL ACCEPT
TERMINAL FLAG
1
0(LSB)
9
TABLE 22. CONFIGURATION REGISTER #7
(READ/WRITE 19H)
TABLE 24. BC GENERAL PURPOSE FLAG REGISTER
(WRITE 1BH)
BIT
DESCRIPTION
MEMORY MANAGEMENT BASE ADDRESS 15
MEMORY MANAGEMENT BASE ADDRESS 14
MEMORY MANAGEMENT BASE ADDRESS 13
MEMORY MANAGEMENT BASE ADDRESS 12
MEMORY MANAGEMENT BASE ADDRESS 11
MEMORY MANAGEMENT BASE ADDRESS 10
RESERVED
BIT
DESCRIPTION
15(MSB)
15(MSB) CLEAR GENERAL PURPOSE FLAG 7
14
14
CLEAR GENERAL PURPOSE FLAG 6
CLEAR GENERAL PURPOSE FLAG 5
CLEAR GENERAL PURPOSE FLAG 4
CLEAR GENERAL PURPOSE FLAG 3
CLEAR GENERAL PURPOSE FLAG 2
CLEAR GENERAL PURPOSE FLAG 1
CLEAR GENERAL PURPOSE FLAG 0
SET GENERAL PURPOSE FLAG 7
SET GENERAL PURPOSE FLAG 6
SET GENERAL PURPOSE FLAG 5
SET GENERAL PURPOSE FLAG 4
SET GENERAL PURPOSE FLAG 3
SET GENERAL PURPOSE FLAG 2
SET GENERAL PURPOSE FLAG 1
SET GENERAL PURPOSE FLAG 0
13
13
12
12
11
11
10
10
9
9
8
RESERVED
8
7
7
RESERVED
6
6
RESERVED
5
5
RESERVED
4
4
RT HALT ENABLE
3
3
1553B RESPONSE TIME
2
2
ENHANCED TIMETAG SYNCHRONIZE
ENHANCED BC WATCHDOG TIMER ENABLED
MODE CODE RESET / INCMD SELECT
1
1
0(LSB)
0(LSB)
TABLE 25. BIT TEST STATUS FLAG REGISTER
(READ 1CH)
TABLE 23. BC CONDITION REGISTER
(READ 1BH)
BIT
DESCRIPTION
BIT
DESCRIPTION
15(MSB) PROTOCOL BUILT-IN TEST COMPLETE
15(MSB) ALWAYS
14
RETRY 1
14
PROTOCOL BUILT-IN TEST IN-PROGRESS
PROTOCOL BUILT-IN TEST PASSED
PROTOCOL BUILT-IN TEST ABORT
LOGIC ”1”
13
RETRY 0
13
12
BAD MESSAGE
12
11
MESSAGE STATUS SET
GOOD BLOCK TRANSFER
FORMAT ERROR
11
10
10
LOGIC ”0”
9
9
LOGIC ”0”
8
NO RESPONSE
8
LOGIC ”0”
7
GENERAL PURPOSE FLAG 7
GENERAL PURPOSE FLAG 6
GENERAL PURPOSE FLAG 5
GENERAL PURPOSE FLAG 4
GENERAL PURPOSE FLAG 3
GENERAL PURPOSE FLAG 2
LESS THAN FLAG / GENERAL PURPOSE FLAG 1
EQUAL FLAG / GENERAL PURPOSE FLAG 1
7
RAM BUILT-IN TEST COMPLETE
RAM BUILT-IN TEST IN-PROGRESS
RAM BUILT-IN TEST IN-PASSED
LOGIC ”0”
6
6
5
5
4
4
3
3
LOGIC ”0”
2
2
LOGIC ”0”
1
1
LOGIC ”0”
0(LSB)
0(LSB)
LOGIC ”0”
10
TABLE 26. INTERRUPT MASK REGISTER #2
(READ/WRITE 1DH)
TABLE 28. BC GENERAL PURPOSE QUEUE POINTER REGISTER
RT, MT INTERRUPT STATUS QUEUE POINTER REGISTER
(READ/WRITE1FH)
BIT
15(MSB) NOT USED
DESCRIPTION
BIT
DESCRIPTION
15(MSB) QUEUE POINTER BASE ADDRESS 15
14
13
BC OP CODE PARITY ERROR
14
QUEUE POINTER BASE ADDRESS 14
QUEUE POINTER BASE ADDRESS 13
QUEUE POINTER BASE ADDRESS 12
QUEUE POINTER BASE ADDRESS 11
QUEUE POINTER BASE ADDRESS 10
QUEUE POINTER BASE ADDRESS 9
QUEUE POINTER BASE ADDRESS 8
QUEUE POINTER BASE ADDRESS 7
QUEUE POINTER BASE ADDRESS 6
QUEUE POINTER ADDRESS 5
ILLEGAL COMMAND
13
GENERAL PURPOSE QUEUE /
INTERRUPT STATUS QUEUE ROLLOVER
12
12
11
CALL STACK POINTER REGISTER ERROR
BC TRAP OP CODE
11
10
10
9
RT COMMAND STACK 50% ROLLOVER
RT CIRCULAR BUFFER 50% ROLLOVER
MONITOR COMMAND STACK 50% ROLLOVER
MONITOR DATA STACK 50% ROLLOVER
ENHANCED BC IRQ3
9
8
8
7
7
6
6
5
5
4
ENHANCED BC IRQ2
4
QUEUE POINTER ADDRESS 4
3
ENHANCED BC IRQ1
3
QUEUE POINTER ADDRESS 3
2
ENHANCED BC IRQ0
2
QUEUE POINTER ADDRESS 2
1
BIT TEST COMPLETE
1
QUEUE POINTER ADDRESS 1
0(LSB)
NOT USED
0(LSB)
QUEUE POINTER ADDRESS 0
TABLE 27. INTERRUPT STATUS REGISTER #2
(READ 1EH)
BIT
DESCRIPTION
15(MSB) MASTER INTERRUPT
14
13
BC OP CODE PARITY ERROR
ILLEGAL COMMAND
GENERAL PURPOSE QUEUE /
INTERRUPT STATUS QUEUE ROLLOVER
12
11
CALL STACK POINTER REGISTER ERROR
BC TRAP OP CODE
10
9
RT COMMAND STACK 50% ROLLOVER
RT CIRCULAR BUFFER 50% ROLLOVER
MONITOR COMMAND STACK 50% ROLLOVER
MONITOR DATA STACK 50% ROLLOVER
ENHANCED BC IRQ3
8
7
6
5
4
ENHANCED BC IRQ2
3
ENHANCED BC IRQ1
2
ENHANCED BC IRQ0
1
BIT TEST COMPLETE
0(LSB)
INTERRUPT CHAIN BIT
11
NOTE: TABLES 29 TO 35 ARE NOT REGISTERS, BUT THEY ARE WORDS STORED IN RAM.
TABLE 29. BC MODE BLOCK STATUS WORD
TABLE 31. 1553 COMMAND WORD
DESCRIPTION
BIT
DESCRIPTION
BIT
EOM
15(MSB)
15(MSB) REMOTE TERMINAL ADDRESS BIT 4
14
SOM
14
REMOTE TERMINAL ADDRESS BIT 3
REMOTE TERMINAL ADDRESS BIT 2
REMOTE TERMINAL ADDRESS BIT 1
REMOTE TERMINAL ADDRESS BIT 0
TRANSMIT / RECEIVE
13
CHANNEL B/A
13
12
ERROR FLAG
12
11
STATUS SET
11
10
FORMAT ERROR
10
9
NO RESPONSE TIMEOUT
LOOP TEST FAIL
9
SUBADDRESS / MODE BIT 4
8
8
SUBADDRESS / MODE BIT 3
7
MASKED STATUS SET
RETRY COUNT 1
7
SUBADDRESS / MODE BIT 2
6
6
SUBADDRESS / MODE BIT 1
5
RETRY COUNT 0
5
SUBADDRESS / MODE BIT 0
4
GOOD DATA BLOCK TRANSFER
WRONG STATUS ADDRESS / NO GAP
WORD COUNT ERROR
INCORRECT SYNC TYPE
INVALID WORD
4
DATA WORD COUNT / MODE CODE BIT 4
DATA WORD COUNT / MODE CODE BIT 3
DATA WORD COUNT / MODE CODE BIT 2
DATA WORD COUNT / MODE CODE BIT 1
DATA WORD COUNT / MODE CODE BIT 0
3
3
2
2
1
1
0(LSB)
0(LSB)
TABLE 32. WORD MONITOR IDENTIFICATION WORD
DESCRIPTION
TABLE 30. RT MODE BLOCK STATUS WORD
DESCRIPTION
BIT
BIT
EOM
15(MSB)
15(MSB) GAP TIME (MSB)
14
SOM
•
•
•
•
13
CHANNEL B/A
•
12
ERROR FLAG
•
11
RT-to-RT FORMAT
8
7
6
5
4
3
2
1
GAP TIME (LSB)
WORD FLAG
THIS RT
10
FORMAT ERROR
9
NO RESPONSE TIMEOUT
LOOP TEST FAIL
8
BROADCAST
ERROR
7
DATA STACK ROLLOVER
ILLEGAL COMMAND WORD
WORD COUNT ERROR
INCORRECT DATA SYNC
INVALID WORD
6
COMMAND / DATA
CHANNEL B/A
CONTIGUOUS DATA / GAP
MODE_CODE
5
4
0(LSB)
3
2
RT-to-RT GAP / SYNC / ADDRESS ERROR
RT-to-RT 2ND COMMAND ERROR
COMMAND WORD CONTENTS ERROR
1
0(LSB)
12
TABLE 33. MESSAGE MONITOR MODE BLOCK STATUS WORD
TABLE 35. 1553B STATUS WORD
DESCRIPTION
BIT
DESCRIPTION
BIT
EOM
15(MSB)
15(MSB) REMOTE TERMINAL ADDRESS BIT 4
14
SOM
14
REMOTE TERMINAL ADDRESS BIT 3
REMOTE TERMINAL ADDRESS BIT 2
REMOTE TERMINAL ADDRESS BIT 1
REMOTE TERMINAL ADDRESS BIT 0
MESSAGE ERROR
13
CHANNEL B/A
ERROR FLAG
RT-to-RT TRANSFER
FORMAT ERROR
13
12
12
11
11
10
10
9
NO RESPONSE TIMEOUT
GOOD DATA BLOCK TRANSFER
DATA STACK ROLLOVER
RESERVED
9
INSTRUMENTATION
8
8
SERVICE REQUEST
7
7
RESERVED
6
6
RESERVED
5
WORD COUNT ERROR
5
RESERVED
4
INCORRECT SYNC
4
BROADCAST COMMAND RECEIVED
BUSY
3
INVALID WORD
3
2
RT-to-RT GAP / SYNC / ADDRESS ERROR
RT-to-RT 2ND COMMAND ERROR
COMMAND WORD CONTENTS ERROR
2
SUBSYSTEM FLAG
1
1
DYNAMIC BUS CONTROL ACCEPTANCE
TERMINAL FLAG
0(LSB)
0(LSB)
TABLE 34. RT/MONITOR INTERRUPT STATUS WORD
(FOR INTERRUPT STATUS QUEUE)
NON-TEST REGISTER FUNCTION SUMMARY
DEFINITION FOR
DEFINTION FOR MESSAGE
NON-MESSAGE
BIT
A summary of the Enhanced Mini-ACE's 24 non-test registers
follows.
INTERRUPT EVENT
INTERRUPT EVENT
15
14
TRANSMITTER TIMEOUT
ILLEGAL COMMAND
NOT USED
NOT USED
Interrupt Mask Registers #1 and #2 are used to enable and
disable interrupt requests for various events and conditions.
MONITOR DATA STACK 50%
ROLLOVER
13
12
11
10
NOT USED
NOT USED
NOT USED
NOT USED
Configuration Registers #1 and #2 are used to select the
Enhanced Mini-ACE's mode of operation, and for software con-
trol of RT Status Word bits, Active Memory Area, BC Stop-On-
Error, RT Memory Management mode selection, and control of
the Time Tag operation.
MONITOR DATA STACK
ROLLOVER
RT CIRCULAR BUFFER 50%
ROLLOVER
RT CIRCULAR BUFFER
ROLLOVER
Start/Reset Register is used for "command" type functions such
as software reset, BC/MT Start, Interrupt reset, Time Tag Reset,
Time Tag Register Test, Initiate protocol self-test, Initiate RAM
self-test, Clear self-test register, and Clear RT Halt. The
Start/Reset Register also includes provisions for stopping the BC
in its auto-repeat mode, either at the end of the current message
or at the end of the current BC frame.
MONITOR COMMAND
(DESCRIPTOR) STACK 50%
ROLLOVER
9
8
NOT USED
NOT USED
MONITOR COMMAND
(DESCRIPTOR) STACK
ROLLOVER
RT COMMAND (DESCRIPTOR)
STACK 50% ROLLOVER
7
6
NOT USED
NOT USED
BC/RT Command Stack Register allows the host CPU to
determine the pointer location for the current or most recent
message.
RT COMMAND (DESCRIPTOR)
STACK ROLLOVER
5
4
HANDSHAKE FAIL
FORMAT ERROR
NOT USED
TIME TAG ROLLOVER
BC Instruction List Pointer Register may be read to determine
the current location of the Instruction List Pointer for the
Enhanced BC mode.
RT ADDRESS PARITY
ERROR
3
MODE CODE INTERRUPT
SUBADDRESS CONTROL
WORD EOM
PROTOCOL SELF-TEST
COMPLETE
2
1
0
BC Control Word/RT Subaddress Control Word Register: In
BC mode, allows host access to the current word or most recent
BC Control Word. The BC Control Word contains bits that select
END-OF-MESSAGE (EOM)
RAM PARITY ERROR
“1” FOR MESSAGE INTERRUPT EVENT
”0” FOR NON-MESSAGE INTERRUPT EVENT
13
the active bus and message format, enable off-line self-test,
masking of Status Word bits, enable retires and interrupts, and
specify MIL-STD-1553A or -1553B error handling. In RT mode,
this register allows host access to the current or most recent
Subaddress Control Word. The Subaddress Control Word is
used to select the memory management scheme and enable
interrupts for the current message.
timer may be also be used for the BC message sequence con-
trol processor's Delay (DLY) instruction, or for minor or major
frame control. The resolution of this register is 1 µs/LSB.
BC FrameTime/ RT Last Command /MTTriggerWord Register.
In BC mode, this register is used to program the BC frame time,
for use in the frame auto-repeat mode. The resolution of this reg-
ister is 100 µs/LS, with a range up to 6.55 seconds. In RT mode,
this register stores the current (or most previous) 1553
Command Word processed by the Enhanced Mini-ACE RT. In
the Word Monitor mode, this register is used to specify a 16-bit
Trigger (Command) Word. The Trigger Word may be used to
start or stop the monitor, or to generate interrupts.
Time Tag Register maintains the value of a real-time clock. The
resolution of this register is programmable from among 2, 4, 8,
16, 32, and 64 µs/LSB. The Start-of-Message (SOM) and End-
of-Message (EOM) sequences in BC, RT, and Message Monitor
modes cause a write of the current value of the Time Tag
Register to the stack area of the RAM.
BC Initial Instruction List Pointer Register enables the host to
Interrupt Status Register #1 and #2 allow the host processor
to determine the cause of an interrupt request by means of one
or two read accesses. The interrupt events of the two Interrupt
Status Registers are mapped to correspond to the respective bit
positions in the two Interrupt Mask Registers. Interrupt Status
Register #2 contains an INTERRUPT CHAIN bit, used to indi-
cate an interrupt event from Interrupt Status Register #1.
assign the starting address for the enhanced BC Instruction List.
RT Status Word Register and BIT Word Registers provide
read-only indications of the RT Status and BIT Words.
Test Mode Registers 0-7. These registers are included for fac-
tory test. In normal operation, these registers do not need to be
accessed by the host processor.
Configuration Registers #3, #4, and #5 are used to enable
many of the Enhanced Mini-ACE's advanced features that were
implemented by the prior generation products, the ACE and
Mini-ACE (Plus). For BC, RT, and MT modes, use of the
ENHANCED MODE enables the various read-only bits in
Configuration Register #1. For BC mode, ENHANCED mode
features include the expanded BC Control Word and BC Block
Status Word, additional Stop-On-Error and Stop-On-Status Set
functions, frame auto-repeat, programmable intermessage gap
times, automatic retires, expanded Status Word Masking, and
the capability to generate interrupts following the completion of
any selected message. For RT mode, the enhanced mode fea-
tures include the expanded RT Block Status Word, combined
RT/Selective Message Monitor mode, automatic setting of the
TERMINAL FLAG Status Word bit following a loop test failure;
the double buffering scheme for individual receive (broadcast)
subaddresses, and the alternate (fully software programmable)
RT Status Word. For MT mode, use of the enhanced mode
enables the Selective Message Monitor, the combined
RT/Selective Monitor modes, and the monitor triggering capabil-
ity.
Configuration Registers #6 and #7 are used to enable the
Enhanced Mini-ACE features that extend beyond the architec-
ture of the ACE/Mini-ACE (Plus). These include the Enhanced
BC mode; RT Global Circular Buffer (including buffer size); the
RT/MT Interrupt Status Queue, including valid/invalid message
filtering; enabling a software-assigned RT address; clock fre-
quency selection; a base address for the "non-data" portion of
Enhanced Mini-ACE memory; LSB filtering for the Synchronize
(with data) time tag operations; and enabling a watchdog timer
for the Enhanced BC message sequence control engine.
BC Condition Code Register is used to enable the host proces-
sor to read the current value of the Enhanced BC Message
Sequence Control Engine's condition flags.
BC General Purpose Flag Register allows the host processor
to be able to set, clear, or toggle any of the Enhanced BC
Message Sequence Control Engine's General Purpose condition
flags.
BIT Test Status Register is used to provide read-only access to
RT/Monitor Data Stack Address Register provides a
read/writable indication of the last data word stored for RT or
Monitor modes.
the status of the protocol and RAM built-in self-tests (BIT).
BC General Purpose Queue Pointer provides a means for ini-
tializing the pointer for the General Purpose Queue, for the
Enhanced BC mode. In addition, this register enables the host to
determine the current location of the General Purpose Queue
pointer, which is incremented internally by the Enhanced BC
message sequence control engine.
BC Frame Time Remaining Register provides a read-only
indication of the time remaining in the current BC frame. In the
enhanced BC mode, this timer may be used for minor or major
frame control, or as a watchdog timer for the BC message
sequence control processor. The resolution of this register is
100 µs/LSB.
RT/MT Interrupt Status Queue Pointer Register provides a
means for initializing the pointer for the Interrupt Status Queue,
for RT, MT, and RT/MT modes. In addition, this register enables
the host to determine the current location of the Interrupt Status
Queue pointer, which is incremented by the RT/MT message
BC Time Remaining to Next Message Register provides a
read-only indication of the time remaining before the start of the
next message in a BC frame. In the enhanced BC mode, this
14
BUS CONTROLLER (BC) ARCHITECTURE
RT-to-RT transfer errors. The Enhanced Mini-ACE BC response
timeout value is programmable with choices of 18, 22, 50, and
130 µs. The longer response timeout values allow for operation
over long buses and/or the use of repeaters.
The BC functionality for the Enhanced Mini-ACE includes two
separate architectures: (1) the older, non-Enhanced mode,
which provides complete compatibility with the previous ACE
and Mini-ACE (Plus) generation products; and (2) the newer,
Enhanced BC mode.The Enhanced BC mode offers several new
powerful architectural features. These includes the incorporation
of a highly autonomous BC message sequence control engine,
which greatly serves to offload the operation of the host CPU.
In its non-Enhanced mode, the Enhanced Mini-ACE may be pro-
grammed to process BC frames of up to 512 messages with no
processor intervention. In the Enhanced BC mode, there is no
explicit limit to the number of messages that may be processed
in a frame. In both modes, it is possible to program for either sin-
gle frame or frame auto-repeat operation. In the auto-repeat
mode, the frame repetition rate may be controlled either inter-
nally, using a programmable BC frame timer, or from an external
trigger input.
The Enhanced BC's message sequence control engine provides
a high degree of flexibility for implementing major and minor
frame scheduling; capabilities for inserting asynchronous mes-
sages in the middle of a frame; to separate 1553 message data
from control/status data for the purpose of implementing double
buffering and performing bulk data transfers; for implementing
message retry schemes, including the capability for automatic
bus channel switchover for failed messages; and for reporting
various conditions to the host processor by means of 4 user-
defined interrupts and a general purpose queue.
ENHANCED BC MODE: MESSAGE SEQUENCE CONTROL
One of the major new architectural features of the Enhanced
Mini-ACE series is its advanced capability for BC message
sequence control. The Enhanced Mini-ACE supports highly
autonomous BC operation, which greatly offloads the operation
of the host processor.
In both the non-Enhanced and Enhanced BC modes, the
Enhanced Mini-ACE BC implements all MIL-STD-1553B mes-
sage formats. Message format is programmable on a message-
The operation of the Enhanced Mini-ACE's message sequence
control engine is illustrated in FIGURE 2. The BC message
sequence control involves an instruction list pointer register; an
instruction list which contains multiple 2-word entries; a message
control/status stack, which contains multiple 8-word or 10-word
descriptors; and data blocks for individual messages.
T/R
by-message basis by means the BC Control Word and the
bit of the Command Word for the respective message. The BC
Control Word allows 1553 message format, 1553A/B type RT,
bus channel, self-test, and Status Word masking to be specified
on an individual message basis. In addition, automatic retries
and/or interrupt requests may be enabled or disabled for individ-
ual messages. The BC performs all error checking required by
MIL-STD-1553B. This includes validation of response time, sync
type and sync encoding, Manchester II encoding, parity, bit
count, word count, Status Word RT Address field, and various
The initial value of the instruction list pointer register is initialized
by the host processor (via Register 0D), and is incremented by
the BC message sequence processor (host readable via
Register 03). During operation, the message sequence control
processor fetches the operation referenced by the instruction list
pointer register from the instruction list.
BC INSTRUCTION
LIST
MESSAGE
CONTROL/STATUS
BLOCK
BC INSTRUCTION
LIST POINTER REGISTER
OP CODE
BC CONTROL
WORD
PARAMETER
(POINTER)
INITIALITIZE BY REGISTER
0D (RD/WR); READ CURRENT
VALUE VIA REGISTER 03
(RD ONLY)
COMMAND WORD
(Rx Command for
RT-to-RT transfer)
DATA BLOCK POINTER
DATA BLOCK
TIME-TO-NEXT MESSAGE
TIME TAG WORD
BLOCK STATUS WORD
LOOPBACK WORD
RT STATUS WORD
2nd (Tx) COMMAND WORD
(for RT-to-RT transfer)
2nd RT STATUS WORD
(for RT-to-RT transfer)
FIGURE 2. BC MESSAGE SEQUENCE CONTROL
15
Note that the pointer parameter referencing the first word of a
message's control/status block (the BC Control Word) must con-
tain an address value that is modulo 8. Also, note that if the
message is an RT-to-RT transfer, the pointer parameter must
contain an address value that is modulo 16.
As shown in TABLE 36, many of the operations include a single-
word parameter. For an XEQ (execute message) operation, the
parameter is a pointer to the start of the message’s Control /
Status block. For other operations, the parameter may be an
address, a time value, an interrupt pattern, a mechanism to set
or clear general purpose flag bits, or an immediate value. For
several op codes, the parameter is "don't care" (not used).
OP CODES
The instruction list pointer register references a pair of words in
the BC instruction list: an op code word, followed by a parameter
word. The format of the op code word, which is illustrated in FIG-
URE 3, includes a 5-bit op code field and a 5-bit condition code
field. The op code identifies the instruction to be executed by the
BC message sequence controller.
As described above, some of the op codes will cause the mes-
sage sequence control processor to execute messages. In this
case, the parameter references the first word of a message
Control/Status block. With the exception of RT-to-RT transfer
messages, all message status/control blocks are eight words
long: a block control word, time-to-next-message parameter,
data block pointer, command word, status word, loopback word,
block status word, and time tag word.
Most of the operations are conditional, with execution dependent
on the contents of the condition code field. Bits 3-0 of the condi-
tion code field identifies a particular condition. Bit 4 of the condi-
tion code field identifies the logic sense ("1" or "0") of the select-
ed condition code on which the conditional execution is depen-
dent. TABLE 36 lists all the op codes, along with their respective
mnemonic, code value, parameter, and description. TABLE 37
defines all the condition codes.
In the case of an RT-to-RT transfer message, the size of the mes-
sage control/status block increases to 16 words. However, in this
case, the last six words are not used; the ninth and tenth words
are for the second command word and second status word.
The third word in the message control/status block is a pointer
that references the first word of the message's data word block.
Note that the data word block stores only data words, which are
to be either transmitted or received by the BC. By segregating
data words from command words, status words, and other con-
trol and "housekeeping" functions, this architecture enables the
use of convenient, usable data structures, such as circular
buffers and double buffers.
Eight of the condition codes (8 through F) are set or cleared as
the result of the most recent message. The other eight are
defined as "General Purpose" condition codes GP0 through
GP7.There are three mechanisms for programming the values of
the General Purpose Condition Code bits: (1) They may be set,
cleared, or toggled by the host processor, by means of the BC
GENERAL PURPOSE FLAG REGISTER; (2) they may be set,
cleared, or toggled by the BC message sequence control
processor, by means of the GP Flag Bits (FLG) instruction; and
(3) GP0 and GP1 only (but none of the others) may be set or
cleared by means of the BC message sequence control proces-
sor's Compare Frame Timer (CFT) or Compare Message Timer
(CMT) instructions.
Other operations support program flow control; i.e., jump and call
capability.The call capability includes maintenance of a call stack
which supports a maximum of four (4) entries; there is also a
return instruction. In the case of a call stack overrun or underrun,
the BC will issue a CALL STACK POINTER REGISTER ERROR
interrupt, if enabled.
The host processor also has read-only access to the BC condi-
tion codes by means of the BC CONDITION CODE REGISTER.
Other op codes may be used to delay for a specified time; start
a new BC frame; wait for an external trigger to start a new frame;
do comparisons based on frame time and time-to-next message;
load the time tag or frame time registers; halt; and issue host
interrupts. In the case of host interrupts, the message control
processor passes a 4-bit user-defined interrupt vector to the
host, by means of the Enhanced Mini-ACE's Interrupt Status
Register.
Note that four (4) instructions are unconditional. These are
Compare to Frame Timer (CFT), Compare to Message Timer
(CMT), GP Flag Bits (FLG), and Execute and Flip (XQF). For
these instructions, the Condition Code Field is "don't care". That
is, these instructions are always executed, regardless of the
result of the condition code test.
All of the other instructions are conditional. That is, they will only
be executed if the condition code specified by the condition code
field in the op code word tests true. If the condition code field
tests false, the instruction list pointer will skip down to the next
instruction.
The purpose of the FLG instruction is to enable the message
sequence controller to set, clear, or toggle the value(s) of any or
all of the eight general purpose condition flags.
The op code parity bit encompasses all sixteen bits of the op
code word. This bit must be programmed for odd parity. If the
message sequence control processor fetches an undefined op
15 14
1
13
12
11
10
9
0
8
1
7
0
6
1
5
0
4
3
2
1
0
OpCode Field
Condition Code Field
16
code word, an op code word with even parity, or bits 9-5 of an op
code word do not have a binary pattern of 01010, the message
sequence control processor will immediately halt the BC's oper-
ation. In addition, if enabled, a BC TRAP OP CODE interrupt will
be issued. Also, if enabled, a parity error will result in an OP
CODE PARITY ERROR interrupt.
TABLE 37 describes the Condition Codes.
TABLE 36. BC OPERATIONS FOR MESSAGE SEQUENCE CONTROL
CONDITIONAL
OR
UNCONDITIONAL
OP CODE
(HEX)
INSTRUCTION MNEMONIC
PARAMETER
DESCRIPTION
Execute
Message
XEQ
0001
Message Control /
Status Block
Address
Conditional
Executes the message at the specified Message Control/Status
Block Address if the condition flag tests TRUE, otherwise contin-
ue execution at the next OpCode in the instruction list.
Jump
JMP
CAL
0002
0003
Instruction List
Addrss
Conditional
Conditional
Jump to the OpCode specified in the Instruction List if the condi-
tion flag tests TRUE, otherwise continue execution at the next
OpCode in the instruction list.
Subroutine
Call
Instruction List
Addrss
Jump to the OpCode specified by the Instruction List Address
and push the Address of the Next OpCode on the Call Stack if
the condition flag test TRUE, otherwise continue execution at
the next OpCode in the instruction list. Note that the maximum
depth of the subroutine call stack is four.
Subroutine
Retrn
RTN
IRQ
0004
0006
Not Used
(Don’t Care)
Conditional
Conditional
Return to the OpCode popped off the Call Stack if the condition
flag tests TRUE, otherwise continue execution at the next
OpCode in the instruction list.
Interrupt
Request
Interrupt
Bit Pattern
in 4 LS bits
Generate an interrupt if the condition flag tests TRUE, otherwise
continue execution at the next OpCode in the instruction list.
The passed parameter (Interrupt Bit Pattern) specifies which of
the ENHANCED BC IRQ bit(s) (bits 5-2) will be set in Interrupt
Status Register #2. Only the four LSBs of the passed parameter
are used. A parameter where the four LSBs are logic "0" will
not generate an interrupt.
Halt
HLT
DLY
WFT
0007
0008
0009
Not Used
(Don’t Care)
Conditional
Conditional
Conditional
Stop execution of the Message Sequence Control Program until
a new BC Start is issued by the host if the condition flag tests
TRUE, otherwise continue execution at the next OpCode in the
instruction list.
Delay
Delay Time Value
(Resolution = 1µS)
Delay the time specified by the Time parameter before executing
the next OpCode if the condition flag tests TRUE, otherwise
continue execution at the next OpCode without delay. The delay
generated will use the Time to Next Message Timer.
Wait Until
Frame Timer
= 0
Not Used
(Don’t Care)
Wait until Frame Time counter is equal to Zero before continuing
execution of the Message Sequence Control Program if the
condition flag tests TRUE, otherwise continue execution at the
next OpCode without delay.
Compare to
Frame Timer
CFT
CMT
FLG
000A
000B
000C
Delay Time Value
(Resolution
= 100µS / LSB)
Unconditional
Unconditional
Unconditional
Compare Time Value to Frame Time Counter and set or clear
the LT and EQ flag based on the results of the compare.
Compare to
Message
Timer
Delay Time Value
(Resolution
= 1µS / LSB)
Compare Time Value to Message Time Counter and set or clear
the LT and EQ flag based on the results of the compare.
GP Flag Bits
Used to set,
clear, or toggle GP
(General Purpose)
Flag bits
Used to set, toggle, or clear any or all of the eight general pur-
pose flags. The table below illustrates the use of the GP Flag
Bits instruction for the case of GP0 (General Purpose Flag 0).
Bits 1 and 9 of the parameter byte affect flag GP1, bits 2 and 10
effect GP2, etc., according to the following rules:
(See description)
Bit 8
Bit 0
Effect on GP0
0
0
1
1
0
1
0
1
No Change
Set Flag
Clear Flag
Toggle Flag
17
TABLE 36. BC OPERATIONS FOR MESSAGE SEQUENCE CONTROL (Cont’d)
CONDITIONAL
OP CODE
INSTRUCTION MNEMONIC
PARAMETER
OR
DESCRIPTION
(HEX)
UNCONDITIONAL
Load Time Tag
Counter
LTT
000D
Time Value.
Resolution
(µs/LSB) is
Conditional
Load Time Tag Counter with Time Value if the condition flag
tests TRUE, otherwise continue execution at the next
OpCode in the instruction list.
defined by bits 9,
8, and 7 of
Configuration
Register #2.
Load Frame
TimerLoad
Frame
LFT
SFT
PPT
PBS
PSI
000E
000F
0010
0011
0012
0013
0014
Time Value (reso-
lution = 100
µs/LSB)
Conditional
Conditional
Conditional
Conditional
Conditional
Conditional
Conditional
Load Frame Timer Register with the Time Value parameter
if the condition flag tests TRUE, otherwise continue execu-
tion at the next OpCode in the instruction list.
Start Frame
Timer
Not Used
(Don't Care)
Start Frame Time Counter with Time Value in Time Frame
register if the condition flag tests TRUE, otherwise continue
execution at the next OpCode in the instruction list.
Push Time Tag
Register
Not Used
(Don't Care)
Push the value of the Time Tag Register on the General
Purpose Queue if the condition flag tests TRUE, otherwise
continue execution at the next OpCode in the instruction
list.
Push Block
Status Word
Not Used
(Don't Care)
Push the Block Status Word for the most recent message on
the General Purpose Queue if the condition flag tests TRUE,
otherwise continue execution at the next OpCode in the
instruction list.
Push
Immediate
Value
Immediate Value
Push Immediate data on the General Purpose Queue if the
condition flag tests TRUE, otherwise continue execution at
the next OpCode in the instruction list.
Push Indirect
PSM
WTG
Memory
Address
Push the data stored at the specified memory location on
the General Purpose Queue if the condition flag tests TRUE,
otherwise continue execution at the next OpCode in the
instruction list.
Wait for
External
Trigger
Not Used
(Don't Care)
Wait for a logic "0"-to-logic "1" transition on the EXT_TRIG
input signal before proceeding to the next OpCode in the
instruction list if the condition flag tests TRUE, otherwise
continue execution at the next OpCode without delay
.
Execute and
Flip
XQF
0015
Message
Control /
Status Block
Address
Unconditional
Execute (unconditionally) the message referenced by the
Message Control/Status Block Address. Following the pro-
cessing of this message, if the condition flag tests TRUE,
the BC will toggle bit 4 in the Message Control/Status Block
Address, and store the new Message Block Address as the
updated value of the parameter following the XQF instruc-
tion code. As a result, the next time that this line in the
instruction list is executed, the Message Control/Status
Block at the updated address (old address XOR 0010h),
rather than the old address, will be processed. If the condi-
tion flag tests FALSE, the value of the Message
Control/Status Block Address parameter will not change.
18
TABLE 37. CONDITION CODES
FUNCTIONAL DESCRIPTION
BIT
CODE
NAME
(BIT 4 = 0)
INVERSE
(BIT 4 = 1)
0
1
LT/GP0
GT/GP0
NE/GP1
Less Than Flag set or cleared after CFT or CMT operation. Also, General Purpose Flag 0 may be set or
cleared by a FLG operation.
EQ/GP1
Equal Flag set or cleared after CFT or CMT operation. Also, General Purpose Flag 1 may also be set or
cleared by a FLG operation.
2
3
4
5
6
7
GP2
GP3
GP4
GP5
GP6
GP7
GP2
GP3
GP4
GP5
GP6
GP7
General Purpose Flags may be set, cleared, or toggled by a FLG operation. The host processor can
set, clear, or toggle these flags in the same way as the FLG instruction by means of the BC GENERAL
PURPOSE FLAG REGISTER.
8
NORESP
RESP
NORESP indicates that an RT has either not responded or has responded later than the BC No
Response Timeout time. The Enhanced Mini-ACE's No Response Timeout Time is defined per
MIL-STD-1553B as the time from the mid-bit crossing of the parity bit of the last word transmitted by the
BC to the mid-sync crossing of the RT Status Word. The value of the No Response Timeout value is
programmable from among the nominal values 18.5, 22.5, 50.5, and 130 µs (±1 µs) by means of bits 10
and 9 of Configuration Register #5.
9
FMT ERR
FMT ERR FMT ERR indicates that the received portion of the most recent message contained one or more viola-
tions of the 1553 message validation criteria (sync, encoding, parity, bit count, word count, etc.), or the
RT's status word received from a responding RT contained an incorrect RT address field.
A
GD BLK
XFER
GD BLK
XFER
For the most recent message, GD BLK XFER will be set to logic "1" following completion of a valid
(error-free) RT-to-BC transfer, RT-to-RT transfer, or transmit mode code with data message. This bit is
set to logic "0" following an invalid message. GOOD DATA BLOCK TRANSFER is always logic "0" fol-
lowing a BC-to-RT transfer, a mode code with data, or a mode code without data. The Loop Test has
no effect on GOOD DATA BLOCK TRANSFER. GOOD DATA BLOCK TRANSFER may be used to
determine if the transmitting portion of an RT-to-RT transfer was error free.
B
MASKED
STATUS
BIT
MASKED Indicates that one or both of the following conditions have occurred for the most recent message: (1) If
STATUS
BIT
one (or more) of the Status Mask bits (14 through 9) in the BC Control Word is logic "0" and the corre-
sponding bit(s) is (are) set (logic "1") in the received RT Status Word. In the case of the RESERVED
BITS MASK (bit 9) set to logic "0," any or all of the 3 Reserved Status Word bits being set will result in
a MASKED STATUS SET condition; and/or (2) If BROADCAST MASK ENABLED/XOR (bit 11 of
Configuration Register #4) is logic "1" and the MASK BROADCAST bit of the message's BC Control
Word is logic "0" and the BROADCAST COMMAND RECEIVED bit in the received RT Status Word is
logic "1.".
C
BAD
GOOD
BAD MESSAGE indicates either a format error, loop test fail, or no response error for the most recent
MESSAGE
MESSAGE message. Note that a "Status Set" condition has no effect on the "BAD MESSAGE/GOOD MESSAGE"
condition code.
D
E
RETRY0
RETRY1
RETRY0
These two bits reflect the retry status of the most recent message. The number of times that the mes-
sage was retried is delineated by these two bits as shown below:
RETRY01
RETRY COUNT 1
RETRY COUNT 0
Number of
(bit 14)
(bit 13)
Message Retries
0
0
1
1
0
1
0
1
0
1
N/A
2
F
ALWAYS
NEVER
The ALWAYS bit should be set to designate an instruction as unconditional. The inverse (NEVER) bit
can be used to implement a NOP instruction.
19
BC MESSAGE SEQUENCE CONTROL
processed, rather than the one at the old address. The operation
of the XQF instruction is illustrated in FIGURE 4.
The BC Enhanced Mini-ACE BC message sequence control
capability enables a high degree of offloading of the host proces-
sor. This includes using the various timing functions to enable
autonomous structuring of major and minor frames. In addition,
by implementing conditional jumps and subroutine calls, the
message sequence control processor greatly simplifies the
insertion of asynchronous, or "out-of-band" messages.
There are multiple ways of utilizing the "execute and flip" instruc-
tion. One is to facilitate the implementation of a double buffering
data scheme for individual messages. This allows the message
sequence control processor to "ping-pong" between a pair of
data buffers for a particular message. By so doing, the host
processor can access one of the two Data Word blocks, while the
BC reads or writes the alternate Data Word block.
Execute and Flip Operation. The Enhanced Mini-ACE BC's
XQF, or "Execute and Flip" operation, provides some unique
capabilities. Following execution of this unconditional instruction,
if the condition code tests TRUE, the BC will modify the value of
the current XQF instruction's pointer parameter by toggling bit 4
of the pointer. That is, if the selected condition flag tests true, the
value of the parameter will be updated to the value = old
address XOR 0010h. As a result, the next time that this line in
the instruction list is executed, the Message Control/Status Block
at the updated address (old address XOR 0010h) will be
A second application of the "execute and flip" capability is in con-
junction with message retries. This allows the BC to not only
switch buses when retrying a failed message, but to automati-
cally switch buses permanently for all future times that the same
message is to be processed. This not only provides a high
degree of autonomy from the host CPU, but saves BC band-
width, by eliminating the need for future attempts to process
messages on an RT's failed channel.
(part of) BC INSTRUCTION LIST
MESSAGE
CONTROL/STATUS
BLOCK 0
XQF
POINTER
XX00h
POINTER
DATA BLOCK 0
MESSAGE
CONTROL/STATUS
BLOCK 1
XX00h
DATA BLOCK 1
POINTER
FIGURE 4. EXECUTE and FLIP (XQF) OPERATION
20
GENERAL PURPOSE QUEUE
Queue. Note that the BC General Purpose Queue Pointer
Register will always point to the next address location (modulo
64); that is, the location following the last location written by the
BC message sequence control engine.
General Purpose Queue. The Enhanced Mini-ACE BC allows
for the creation of a general purpose queue. This data structure
provides a means for the message sequence processor to con-
vey information to the BC host. The BC op code repertoire pro-
vides mechanisms to push various items on this queue. These
include the contents of the Time Tag Register, the Block Status
Word for the most recent message, an immediate data value, or
the contents of a specified memory address.
If enabled, a BC GENERAL PURPOSE QUEUE ROLLOVER
interrupt will be issued when the value of the queue pointer
address rolls over at a 64-word boundary.The rollover will always
occur at a modulo 64 address.
FIGURE 5 illustrates the operation of the BC General Purpose
BC GENERAL
PURPOSE QUEUE
(64 Locations)
LAST LOCATION
NEXT LOCATION
BC GENERAL
PURPOSE QUEUE
POINTER
REGISTER
FIGURE 5. BC GENERAL PURPOSE QUEUE
21
REMOTE TERMINAL (RT) ARCHITECTURE
ging, and an "auto-boot" feature which allows the RT to initialize
as an online RT with the busy bit set following power turn-on.
The Enhanced Mini-ACE's RT architecture builds upon that of the
ACE and Mini-ACE. The Enhanced Mini-ACE provides multipro-
tocol support, with full compliance to all of the commonly used
data bus standards, including MIL-STD-1553A, MIL-STD-1553B
Notice 2, STANAG 3838, General Dynamics 16PP303, and
McAirA3818, A5232, and A5690. For the Enhanced Mini-ACE RT
mode, there is programmable flexibility enabling the RT to be con-
figured to fulfill any set of system requirements. This includes the
capability to meet the MIL-STD-1553A response time require-
ment of 2 to 5 µs, and multiple options for mode code subad-
dresses, mode codes, RT status word, and RT BIT word.
RT MEMORY ORGANIZATION
TABLE 38 illustrates a typical memory map for an Enhanced Mini-
ACE RT with 4K RAM.The two Stack Pointers reside in fixed loca-
tions in the shared RAM address space: address 0100 (hex) for
the Area A Stack Pointer and address 0104 for the Area B Stack
Pointer. In addition to the Stack Pointer, there are several other
areas of the shared RAM address space that are designated as
fixed locations (all shown in bold). These are for the Area A and
Area B lookup tables, the illegalization lookup table, the busy
lookup table, and the mode code data tables.
The Enhanced Mini-ACE RT protocol design implements all of the
MIL-STD-1553B message formats and dual redundant mode
codes. The design has passed validation testing for MIL-STD-
1553B compliance. The Enhanced Mini-ACE RT performs com-
prehensive error checking including word and format validation,
and checks for various RT-to-RT transfer errors. One of the main
features of the Enhanced Mini-ACE RT is its choice of memory
management options. These include single buffering by subad-
dress, double buffering for individual receive subaddresses, cir-
cular buffering by individual subaddresses, and global circular
buffering for multiple (or all) subaddresses.
The RT lookup tables (reference TABLE 39) provide a mechanism
for allocating data blocks for individual transmit, receive, or broad-
cast subaddresses. The RT lookup tables include subaddress
control words as well as the individual data block pointers. If com-
mand illegalization is used, address range 0300-03FF is used for
command illegalizing. The descriptor stack RAM area, as well as
the individual data blocks, may be located in any of the non-fixed
areas in the shared RAM address space.
Note that in TABLE 38, there is no area allocated for "Stack B".
This is shown for purpose of simplicity of illustration. Also, note
that in TABLE 38, the allocated area for the RT command stack is
256 words. However, larger stack sizes are possible. That is, the
RT command stack size may be programmed for 256 words (64
messages), 512, 1024, or 2048 words (512 messages) by means
of bits 14 and 13 of Configuration Register 3.
Other features of the Enhanced Mini-ACE RT include a set of
interrupt conditions, an flexible status queue with filtering based
on valid and/or invalid messages, flexible command illegalization,
programmable busy by subaddress, multiple options on time tag-
TABLE 39. RT LOOK-UP TABLES
TABLE 38. TYPICAL RT MEMORY MAP (SHOWN FOR 4K RAM)
AREA A
AREA B
DESCRIPTION
COMMENT
ADDRESS
DESCRIPTION
(HEX)
0140
.
.
.
01C0
.
.
.
Rx(/Bcst) SA0
Receive
(/Broadcast)
Lookup Pointer
Table
0000-00FF
0100
Stack A
Stack Pointer A
Global Circular Buffer A Pointer
RESERVED
.
.
.
0101
015F
01DF
Rx(/Bcst) SA31
0102-0103
0104
0160
.
.
.
01E0
.
.
.
Tx SA0
Transmit
Lookup Pointer
Table
Stack Pointer B
Global Circular Buffer B Pointer
RESERVED
.
.
.
0105
0106-0107
0108-010F
0110-013F
0140-01BF
01C0-023F
0240-0247
0248-025F
0260-027F
0280-02FF
0300-03FF
0400-041F
0420-043F
·•
017F
01FF
Tx SA31
Mode Code Selective Interrupt Table
Mode Code Data
Lookup Table A
Lookup Table B
Busy Bit Lookup Table
(not used)
0180
.
.
.
0200
.
.
.
Bcst SA0
Broadcast
Lookup Pointer
Table
.
.
.
(Optional)
019F
021F
Bcst SA31
01A0
.
.
.
0220
.
.
.
SACW SA0
Subaddress
Control Word
Lookup Pointer
Table
.
.
.
Data Block 0
Data Block 1-4
01BF
023F
SACW SA31
(Optional)
Command Illegalizing Table
Data Block 5
Data Block 6
•
•
•
•
•
0FE0-0FFF
Data Block 100
22
RT MEMORY MANAGEMENT
Like the subaddress circular buffer, the size of the global circular
buffer is programmable, with a range of 128 to 8192 data words.
The Enhanced Mini-ACE provides a variety of RT memory man-
agement capabilities. As with the ACE and Mini-ACE, the choice
of memory management scheme is fully programmable on a
transmit/receive/broadcast subaddress basis.
The double buffering feature provides a means for the host
processor to easily access the most recent, complete received
block of valid Data Words for any given subaddress. In addition
to helping ensure data sample consistency, the circular buffer
options provide a means for greatly reducing host processor
overhead for multi-message bulk data transfer applications.
In compliance with MIL-STD-1553B Notice 2, received data from
broadcast messages may be optionally separated from non-
broadcast received data. For each transmit, receive or broadcast
subaddress, either a single-message data block, a double
buffered configuration (two alternating Data Word blocks), or a
variable-sized (128 to 8192 words) subaddress circular buffer
may be allocated for data storage. The memory management
scheme for individual subaddresses is designated by means of
the subaddress control word (reference TABLE 40).
End-of-message interrupts may be enabled either globally (fol-
lowing all messages), following error messages, on
a
transmit/receive/broadcast subaddress or mode code basis, or
when a circular buffer reaches its midpoint (50% boundary) or
lower (100%) boundary. A pair of interrupt status registers allow
the host processor to determine the cause of all interrupts by
means of a single read operation.
For received data, there is also a global circular buffer mode. In
this configuration, the data words received from multiple (or all)
subaddresses are stored in a common circular buffer structure.
TABLE 40. RT SUBADDRESS CONTROL WORD - MEMORY MANAGEMENT OPTIONS
DOUBLE-BUFFERED OR
GLOBAL CIRCULAR BUFFER
(bit 15)
SUBADDRESS CONTROL WORD BITS
MEMORY MANAGEMENT SUBADDRESS
BUFFER SCHEME DESCRIPTION
MM2
MM1
MM0
0
0
0
0
Single Message
For Receive or Broadcast:
Double Buffered
1
0
0
0
For Transmit: Single Message
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
1
1
0
0
1
1
1
0
1
0
1
0
1
128-Word
256-Word
512-Word
Subaddress -
specific circular buffer
of specified size.
1024-Word
2048-Word
4096-Word
8192-Word
(for receive and / or broadcast subaddresses only)
Global Circular Buffer: The buffer size is specified by
Configuration Register #6, bits 11-9. The pointer to the global
circular buffer is stored at address 0101 (for Area A) or address
0105 (for Area B)
1
1
1
1
23
SINGLE BUFFERED MODE
the latest, valid, complete data block is always accessible to the
host processor.
The operation of the single buffered RT mode is illustrated in
FIGURE 6. In the single buffered mode, the respective lookup
table entry must be written by the host processor. Received data
words are written to, or transmitted data words are read from the
data word block with starting address referenced by the lookup
table pointer. In the single buffered mode, the current lookup
table pointer is not updated by the Enhanced Mini-ACE memory
management logic. Therefore, if a subsequent message is
received for the same subaddress, the same Data Word block
will be overwritten or overread.
CIRCULAR BUFFER MODE
The operation of the Enhanced Mini-ACE's circular buffer RT
memory management mode is illustrated in FIGURE 8. As in the
single buffered and double buffered modes, the individual lookup
table entries are initially loaded by the host processor. At the
start of each message, the lookup table entry is stored in the
third position of the respective message block descriptor in the
descriptor stack area of RAM. Receive or transmit data words
are transferred to (from) the circular buffer, starting at the loca-
tion referenced by the lookup table pointer.
SUBADDRESS DOUBLE BUFFERING MODE
The Enhanced Mini-ACE provides a double buffering mechanism
for received data, that may be selected on an individual subad-
dress basis for any or all receive (and/or broadcast) subad-
dresses. This is illustrated in FIGURE 7. It should be noted that
the Subaddress Double Buffering mode is applicable for receive
data only, not for transmit data. Double buffering of transmit
messages may be easily implemented by software techniques.
In general, the location after the last data word written or read
(modulo the circular buffer size) during the message is written to
the respective lookup table location during the end-of-message
sequence. By so doing, data for the next message for the respec-
tive transmit, receive(/broadcast), or broadcast subaddress will
be accessed from the next lower contiguous block of locations in
the circular buffer.
The purpose of the subaddress double buffering mode is to pro-
vide data sample consistency to the host processor. This is
accomplished by allocating two 32-word data word blocks for
each individual receive (and/or broadcast receive) subaddress.
At any given time, one of the blocks will be designated as the
"active "1553 block while the other will be considered as "inac-
tive". The data words for the next receive command to that sub-
address will be stored in the active block. Following receipt of a
valid message, the Enhanced Mini-ACE will automatically switch
the active and inactive blocks for that subaddress. As a result,
For the case of a receive (or broadcast receive) message with a
data word error, there is an option such that the lookup table
pointer will only be updated following receipt of a valid message.
That is, the pointer will not be updated following receipt of a
message with an error in a data word. This allows failed mes-
sages in a bulk data transfer to be retried without disrupting the
circular buffer data structure, and without intervention by the
RT's host processor.
GLOBAL CIRCULAR BUFFER
LOOK-UP TABLE
(DATA BLOCK ADDR)
DESCRIPTOR
STACKS
CONFIGURATION
REGISTER
STACK
POINTERS
DATA
BLOCKS
15 13
0
CURRENT
AREA B/A
BLOCK STATUS WORD
TIME TAG WORD
LOOK-UP
TABLE ADDR
DATA BLOCK
DATA BLOCK
DATA BLOCK POINTER
(See note)
RECEIVED COMMAND
WORD
Note: Lookup table is not used for mode commands when enchanced mode codes are enabled.
FIGURE 6. RT SINGLE BUFFERED MODE
24
Beyond the programmable choice of single buffer mode, double
buffer mode, or circular buffer mode, programmable on an indi-
vidual subaddress basis, the Enhanced Mini-ACE RT architec-
ture provides an additional option, a variable sized global circu-
lar buffer. The Enhanced Mini-ACE RT allows for a mix of single
buffered, double buffered, and individually circular buffered sub-
addresses, along with the use of the global double buffer for any
arbitrary group of receive(/broadcast) or broadcast subaddress-
es.
The pointer to the Global Circular Buffer will be stored in location
0101 (for Area A), or location 0105 (for Area B).
The global circular buffer option provides a highly efficient
method for storing received message data. It allows for fre-
quently used subaddresses to be mapped to individual data
blocks, while also providing a method for asynchronously
received messages to infrequently used subaddresses to be
logged to a common area. Alternatively, the global circular
buffer provides an efficient means for storing the received data
words for all subaddresses. Under this method, all received
data words are stored chronologically, regardless of subad-
dress.
In the global circular buffer mode, the data for multiple receive
subaddresses is stored in the same circular buffer data structure.
The size of the global circular buffer may be programmed for
128, 256, 512, 1024, 2048, 4096, or 8192 words, by means of
bits 11, 10, and 9 of Configuration Register #6. As shown in
TABLE 40, individual subaddresses may be mapped to the glob-
al circular buffer by means of their respective subaddress control
words.
CONFIGURATION
REGISTER
STACK
POINTERS
DESCRIPTOR
STACK
LOOK-UP
TABLES
15
13
0
DATA
BLOCKS
CURRENT
AREA B/A
BLOCK STATUS WORD
TIME TAG WORD
X..X 0 YYYYY
DATA
BLOCK 0
DATA BLOCK POINTER
DATA BLOCK POINTER
X..X 1 YYYYY
RECEIVED COMMAND
WORD
DATA
BLOCK 1
RECEIVE DOUBLE
BUFFER ENABLE
MSB
SUBADDRESS
CONTROL WORD
FIGURE 7. RT DOUBLE BUFFERED MODE
CIRCULAR
DATA
CONFIGURATION
REGISTER
STACK
POINTERS
DESCRIPTOR
STACK
LOOK-UP TABLES
BUFFER
15
13
0
CURRENT
AREA B/A
BLOCK STATUS WORD
TIME TAG WORD
POINTER TO
CURRENT
DATA BLOCK
LOOK-UP
TABLE
ADDRESS
DATA BLOCK POINTER
128,
256
LOOK-UP TABLE
ENTRY
RECEIVED COMMAND
WORD
RECEIVED
(TRANSMITTED)
MESSAGE
POINTER TO
NEXT DATA
BLOCK
*
DATA
8192
WORDS
(NEXT LOCATION)
Notes:
CIRCULAR
BUFFER
ROLLOVER
1. TX/RS/BCST_SA look-up table entry is updated following valid receive (broadcast) message
or following completion of transit message
2. For the Global Circular Buffer Mode, the pointer is read from and re-written to Address 0101 (for Area A)
or Adress 0105 (for Area B).
FIGURE 8. RT CIRCULAR BUFFERED MODE
25
RT DESCRIPTOR STACK
The 50% rollover interrupt is beneficial for performing bulk data
transfers. For example, when using circular buffering for a partic-
ular receive subaddress, the 50% rollover interrupt will inform the
host processor when the circular buffer is half full. At that time,
the host may proceed to read the received data words in the
upper half of the buffer, while the Enhanced Mini-ACE RT writes
received data words to the lower half of the circular buffer. Later,
when the RT issues a 100% circular buffer rollover interrupt, the
host can proceed to read the received data from the lower half of
the buffer, while the Enhanced Mini-ACE RT continues to write
received data words to the upper half of the buffer.
The descriptor stack provides a chronology of all messages
processed by the Enhanced Mini-ACE RT. Reference Figures 6,
7, and 8. Similar to BC mode, there is a four-word block descrip-
tor in the Stack for each message processed. The four entries to
each block descriptor are the Block Status Word, Time Tag Word,
the pointer to the start of the message's data block, and the 16-
bit received Command Word.
The RT Block Status Word includes indications of whether a par-
ticular message is ongoing or has been completed, what bus
channel it was received on, indications of illegal commands, and
flags denoting various message error conditions. For the double
buffering, subaddress circular buffering, and global circular
buffering modes, the data block pointer may be used for locating
the data blocks for specific messages. Note that for mode code
commands, there is an option to store the transmitted or
received data word as the third word of the descriptor, in place of
the data block pointer.
Interrupt status queue. The Enhanced Mini-ACE RT, Monitor,
and combined RT/Monitor modes include the capability for gen-
erating an interrupt status queue. As illustrated in Figure 10, this
provides a chronological history of interrupt generating events
and conditions. In addition to the Interrupt Mask Register, the
Interrupt Status Queue provides additional filtering capability,
such that only valid messages and/or only invalid messages may
result in the creation of an entry to the Interrupt Status Queue.
Queue entries for invalid and/or valid messages may be disabled
by means of bits 8 and 7 of configuration register #6.
The Time Tag Word provides a 16-bit indication of relative time
for individual messages. The resolution of the Enhanced Mini-
ACE's time tag is programmable from among 2, 4, 8, 16, 32, or
64 µs/LSB. There is also a provision for using an external clock
input for the time tag (consult factory). If enabled, there is a time
tag rollover interrupt, which is issued when the value of the time
tag rolls over from FFFF(hex) to 0. Other time tag options include
the capabilities to clear the time tag register following receipt of
a Synchronize (without data) mode command and/or to set the
time tag following receipt of a Synchronize (with data) mode
command. For that latter, there is an added option to filter the
"set" capability based on the LSB of the received data word
being equal to logic "0".
The interrupt status queue is 64 words deep, providing the capa-
bility to store entries for up to 32 messages. These events and
conditions include both message-related and non-message
related events. Note that the Interrupt Vector Queue Pointer
Register will always point to the next location (modulo 64) fol-
lowing the last vector/pointer pair written by the Enhanced Mini-
ACE RT.
The pointer to the Interrupt Status Queue is stored in the
INTERRUPT VECTOR QUEUE POINTER REGISTER (register
address 1F). This register must be initialized by the host, and is
subsequently incremented by the RT message processor. The
interrupt status queue is 64 words deep, providing the capability
to store entries for up to 32 messages.
RT INTERRUPTS
The Enhanced Mini-ACE offers a great deal of flexibility in terms
of RT interrupt processing. By means of the Enhanced Mini-
ACE's two Interrupt Mask Registers, the RT may be programmed
to issue interrupt requests for the following events/conditions:
End-of-(every)Message, Message Error, Selected (transmit or
receive) Subaddress, 100% Circular Buffer Rollover, 50%
Circular Buffer Rollover, 100% Descriptor Stack Rollover, 50%
Descriptor Stack Rollover, Selected Mode Code, Transmitter
Timeout, Illegal Command, and Interrupt Status Queue Rollover.
The queue rolls over at addresses of modulo 64. The events that
result in queue entries include both message-related and non-
message-related events. Note that the Interrupt Vector Queue
Pointer Register will always point to the next location (modulo 64)
following the last vector/pointer pair written by the Enhanced
Mini-ACE RT, Monitor, or RT/Monitor.
Each event that causes an interrupt results in a two-word entry
to be written to the queue. The first word of the entry is the inter-
rupt vector. The vector indicates which interrupt event(s)/condi-
tion(s) caused the interrupt.
Interrupts for 50% Rollovers of Stacks and Circular Buffers.
The Enhanced Mini-ACE RT and Monitor are capable of issuing
host interrupts when a subaddress circular buffer pointer or stack
pointer crosses its mid-point boundary. For RT circular buffers,
this is applicable for both transmit and receive subaddresses.
Reference FIGURE 9. There are four interrupt mask and inter-
rupt status register bits associated with the 50% rollover
function:
The interrupt events are classified into two categories: message
interrupt events and non-message interrupt events. Message-
based interrupt events include End-of-Message, Selected mode
code, Format error, Subaddress control word interrupt, RT
Circular buffer Rollover, Handshake failure, RT Command stack
rollover, transmitter timeout, MT Data Stack rollover,
MT Command Stack rollover, RT Command Stack 50% rollover,
MT Data Stack 50% rollover, MT Command Stack 50% rollover,
and RT Circular buffer 50% rollover. Non-message interrupt
(1) RT circular buffer;
(2) RT command (descriptor) stack;
(3) Monitor command (descriptor) stack; and
(4) Monitor data stack.
26
CIRCULAR
BUFFER*
(128,256,...8192 WORDS)
DESCRIPTOR STACK
BLOCK STATUS WORD
TIME TAG WORD
LOOK-UP TABLE
DATA BLOCK POINTER
DATA POINTER
RECIEVED COMMAND WORD
RECIEVED
(TRANSMITTED)
MESSAGE DATA
50%
ROLLOVER
50%
INTERRUPT
Note
100%
ROLLOVER
INTERRUPT
The example shown is for an RT Subaddress Circular Buffer.
The 50% and 100% Rollover Interrupts are also applicable to
the RT Global Circulat Buffer, RT Command Stack,
Monitor Command Stack, and Monitor Data Stack.
100%
FIGURE 9. 50% and 100% ROLLOVER INTERRUPTS
INTERRUPT STATUS QUEUE
(64 Locations)
DESCRIPTOR
STACK
INTERRUPT
VECTOR
PARAMETER
(POINTER)
BLOCK STATUS WORD
INTERRUPT VECTOR
TIME TAG
QUEUE POINTER
REGISTER (IF)
NEXT
VECTOR
DATA BLOCK POINTER
RECIEVED COMMAND
DATA WORD
BLOCK
FIGURE 10. RT (and MONITOR) INTERRUPT STATUS QUEUE
(shown for message Interrupt event)
27
events/conditions include time tag rollover, RT address parity
error, RAM parity error, and BIT completed.
If enabled, an INTERRUPT STATUS QUEUE ROLLOVER inter-
rupt will be issued when the value of the queue pointer address
rolls over at a 64-word address boundary.
Bit 0 of the interrupt vector (interrupt status) word indicates
whether the entry is for a message interrupt event (if bit 0 is logic
"1") or a non-message interrupt event (if bit 0 is logic "0"). It is not
possible for one entry on the queue to indicate both a message
interrupt and a non-message interrupt.
RT COMMAND ILLEGALIZATION
The Enhanced Mini-ACE provides an internal mechanism for RT
Command Word illegalizing. By means of a 256-word area in
shared RAM, the host processor may designate that any mes-
As illustrated in FIGURE 10, for a message interrupt event, the
parameter word is a pointer. The pointer will reference the first
word of the RT or MT command stack descriptor (i.e., the Block
Status Word).
T/R
sage be illegalized, based on the command word
bit, sub-
address, and word count/mode code fields. The Enhanced Mini-
ACE illegalization scheme provides the maximum in flexibility,
allowing any subset of the 4096 possible combinations of broad-
cast/own address, T/R bit, subaddress, and word count/mode
code to be illegalized.
For a RAM Parity Error non-message interrupt, the parameter
will be the RAM address where the parity check failed. For the
RT address Parity Error, Protocol Self-test Complete, and Time
Tag rollover non-message interrupts, the parameter is not used;
it will have a value of 0000.
The address map of the Enhanced Mini-ACE's illegalizing table
is illustrated in TABLE 41.
TABLE 41. ILLEGALIZATION TABLE MEMORY MAP
ADDRESS
300
DESCRIPTION
Brdcst / Rx, SA 0. MC15-0
Brdcst / RX,SA 0. MC31-16
Brdcst / Rx, SA 1. WC15-0
Brdcst / Rx, SA 1. WC31-16
301
302
303
•
•
•
•
•
•
33F
340
341
342
Brdcst / Rx, SA 31. MC31-16
Brdcst / Tx, SA 0. MC15-0
Brdcst / Tx, SA 1.MC31-16
Brdcst / Tx, SA 1. WC15-0
•
•
•
•
•
•
37D
37E
37F
380
381
382
383
Brdcst / Tx, SA 30. WC31-16
Brdcst / Tx, SA 31. MC15-0
Brdcst / Tx, SA 31. MC31-16
Own Addr / Rx, SA 0. MC15-0
Own Addr / Rx, SA 0. MC31-16
Own Addr / Rx, SA 1. WC15-0
Own Addr / Rx, SA 1. WC31-16
•
•
•
•
•
•
3BE
3BF
3C0
3C1
3C2
3C3
Own Addr / Rx, SA 31. MC15-0
Own Addr / Rx, SA 31. MC31-16
Own Addr / Tx, SA 0. MC15-0
Own Addr / Tx, SA 0. MC31-16
Own Addr / Tx, SA 1. WC15-0
Own Addr / Tx, SA 1. WC31-16
•
•
•
•
•
•
3FC
3FD
3FE
3FF
Own Addr / Tx, SA 30. WC15-0
Own Addr / Tx, SA 30. WC31-16
Own Addr / Tx, SA 31. MC15-0
Own Addr / Tx, SA 31. MC31-16
28
BUSY BIT
RT BUILT-IN-TEST (BIT) WORD
The Enhanced Mini-ACE RT provides two different methods for
setting the Busy status word bit: (1) globally, by means of
Configuration Register #1; or (2) on a T/R-bit/subaddress basis,
by means of a RAM lookup table. If the host CPU asserts the
The bit map for the Enhanced Mini-ACE's internal RT Built-in-
Test (BIT) Word is indicated in TABLE 42.
TABLE 42. RT BIT WORD
bit to logic “0“ in Configuration Register #1, the Enhanced
BIT
DESCRIPTION
Mini-ACE RT will respond to all non-broadcast commands with
the Busy bit set in its RT Status Word.
15(MSB) TRANSMITTER TIMEOUT
14
LOOP TEST FAILURE B
Alternatively, there is a Busy lookup table in the Enhanced Mini-
ACE shared RAM. By means of this table, it is possible for the
host processor to set the busy bit for any selectable subset of the
13
LOOP TEST FAILURE A
12
HANDSHAKE FAILURE
11
TRANSMITTER SHUTDOWN B
TRANSMITTER SHUTDOWN A
TERMINAL FLAG INHIBITED
BIT TEST FAILURE
T/R
128 combinations of broadcast/own address,
address.
bit, and sub-
10
9
8
If the busy bit is set for a transmit command, the Enhanced Mini-
ACE RT will respond with the busy bit set in the status word, but
will not transmit any data words. If the busy bit is set for a receive
command, the RT will also respond with the busy status bit set.
There are two programmable options regarding the reception of
data words for a non-mode code receive command for which the
RT is busy: (1) to transfer the received data words to shared
RAM; or (2) to not transfer the data words to shared RAM.
7
HIGH WORD COUNT
6
LOW WORD COUNT
5
INCORRECT SYNC RECEIVED
PARITY / MANCHESTER ERROR RECEIVED
RT-to-RT GAP / SYNC ADDRESS ERROR
RT-to-RT NO RESPONSE ERROR
RT-to-RT 2ND COMMAND WORD ERROR
COMMAND WORD CONTENTS ERROR
4
3
2
1
RT ADDRESS
0(LSB)
The Enhanced Mini-ACE offers several different options for des-
ignating the Remote Terminal address. These include the follow-
ing: (1) hardwired, by means of the 5 RT ADDRESS inputs, and
the RT ADDRESS PARITY input; (2) by means of the RT
ADDRESS (and PARITY) inputs, but latched via hardware, on
the rising edge of the RT_AD_LAT input signal; (3) input by
means of the RT ADDRESS (and PARITY) inputs, but latched via
host software; and (4) software programmable, by means of an
internal register. In all four configurations, the RT address is
readable by the host processor.
RT AUTO-BOOT OPTION
If utilized, the RT pin-programmable auto-boot option allows the
Enhanced Mini-ACE RT to automatically initialize as an active
remote terminal with the Busy status word bit set to logic "1"
immediately following power turn-on. This is a useful feature for
MIL-STD-1760 applications, in which the RT is required to be
responding within 150 ms after power-up. This feature is avail-
able for versions of the Enhanced Mini-ACE with 4K words of
RAM.
OTHER RT FEATURES.
The Enhanced Mini-ACE includes options for the Terminal flag
status word bit to be set either under software control and/or
automatically following a failure of the loopback self-test. Other
software programmable RT options include software program-
mable RT status and RT BIT words, automatic clearing of the
Service Request bit following receipt of a Transmit vector word
mode command, options regarding Data Word transfers for the
Busy and Message error (illegal) Status word bits, and options
for the handling of 1553A and reserved mode codes.
29
MONITOR ARCHITECTURE
The current Monitor address is maintained by means of a
counter register. This value may be read by the CPU by means
of the Data Stack Address Register. It is important to note that
when the counter reaches the Stack Pointer address of 0100 or
0104, the initial pointer value stored in this shared RAM location
will be overwritten by the monitored data and ID Words. When
the internal counter reaches an address of FFFF (or 0FFF, for an
Enhanced Mini-ACE with 4K RAM), the counter rolls over to
0000.
The Enhanced Mini-ACE includes three monitor modes:
(1) A Word Monitor mode.
(2) A selective message monitor mode.
(3) A combined RT/message monitor mode.
For new applications, it is recommended that the selective mes-
sage monitor mode be used, rather than the word monitor mode.
WORD MONITOR TRIGGER
In the Word Monitor mode, there is a pattern recognition trigger
and a pattern recognition interrupt. The 16-bit compare word for
both the trigger and the interrupt is stored in the Monitor Trigger
Word Register. The pattern recognition interrupt is enabled by
setting the MT Pattern Trigger bit in Interrupt Mask Register #1.
The pattern recognition trigger is enabled by setting the Trigger
Enable bit in Configuration Register #1 and selecting either the
Start-on-trigger or the Stop-on-trigger bit in Configuration
Register #1.
T/R
Besides providing monitor filtering based on RT address,
bit, and subaddress, the message monitor eliminates the need to
determine the start and end of messages by software.
WORD MONITOR MODE
In the Word Monitor Terminal mode, the Enhanced Mini-ACE
monitors both 1553 buses. After the software initialization and
Monitor Start sequences, the Enhanced Mini-ACE stores all
Command, Status, and Data Words received from both buses.
For each word received from either bus, a pair of words is stored
to the Enhanced Mini-ACE's shared RAM. The first word is the
word received from the 1553 bus. The second word is the
Monitor Identification (ID), or "Tag" word. The ID word contains
information relating to bus channel, word validity, and inter-word
time gaps. The data and ID words are stored in a circular buffer
in the shared RAM address space.
The Word Monitor may also be started by means of a low-to-high
transition on the EXT_TRIG input signal.
SELECTIVE MESSAGE MONITOR MODE
The Enhanced Mini-ACE Selective Message Monitor provides
monitoring of 1553 messages with filtering based on RT
address, T/R bit, and subaddress with no host processor inter-
vention. By autonomously distinguishing between 1553 com-
mand and status words, the Message Monitor determines when
messages begin and end, and stores the messages into RAM,
WORD MONITOR MEMORY MAP
A typical word monitor memory map is illustrated in TABLE 43.
TABLE 43 assumes a 64K address space for the Enhanced Mini-
ACE's monitor. The Active Area Stack pointer provides the
address where the first monitored word is stored. In the example,
it is assumed that the Active Area Stack Pointer for Area A (loca-
tion 0100) is initialized to 0000. The first received data word is
stored in location 0000, the ID word for the first word is stored in
location 0001, etc.
T/R
based on a programmable filter of RT address,
address.
bit, and sub-
The selective monitor may be configured as just a monitor, or as
a combined RT/Monitor. In the combined RT/Monitor mode, the
Enhanced Mini-ACE functions as an RT for one RT address
(including broadcast messages), and as a selective message
monitor for the other 30 RT addresses. The Enhanced Mini-ACE
Message Monitor contains two stacks, a command stack and a
data stack, that are independent from the RT command stack.
The pointers for these stacks are located at fixed locations in
RAM.
TABLE 43. TYPICAL WORD MONITOR MEMORY MAP
HEX
FUNCTION
ADDRESS
0000
0001
0002
0003
0004
005
First Received 1553 Word
First Identification Word
MONITOR SELECTION FUNCTION
Following receipt of a valid command word in Selective Monitor
mode, the Enhanced Mini-ACE will reference the selective mon-
itor lookup table to determine if the particular command is
enabled. The address for this location in the table is determined
by means of an offset based on the RT Address, T/R bit, and
Subaddress bit 4 of the current command word, and concate-
nating it to the monitor lookup table base address of 0280 (hex).
The bit location within this word is determined by subaddress bits
3-0 of the current command word.
Second Received 1553 Word
Second Identification Word
Third Received 1553 Word
Third Identification Word
•
•
•
•
•
•
Stack Pointer
(Fixed Location - gets overwritten)
0100
•
•
•
•
•
Received 1553 Words and Identification Word
FFFF
•
•
30
If the specified bit in the lookup table is logic "0", the command
is not enabled, and the Enhanced Mini-ACE will ignore this com-
mand. If this bit is logic "1", the command is enabled and the
Enhanced Mini-ACE will create an entry in the monitor command
descriptor stack (based on the monitor command stack pointer),
and store the data and status words associated with the com-
mand into sequential locations in the monitor data stack. In addi-
tion, for an RT-to-RT transfer in which the receive command is
selected, the second command word (the transmit command) is
stored in the monitor data stack.
SELECTIVE MESSAGE MONITOR MEMORY
ORGANIZATION
A typical memory map for the ACE in the Selective Message
Monitor mode, assuming a 4K RAM space, is illustrated in
TABLE 45.This mode of operation defines several fixed locations
in the RAM.These locations are allocated in a way in which none
of them overlap with the fixed RT locations. This allows for the
combined RT/Selective Message Monitor mode.
The address definition for the Selective Monitor Lookup TABLE
is illustrated in TABLE 44.
The fixed memory map consists of two Monitor Command Stack
Pointers (locations 102 and 106 hex), two Monitor Data Stack
Pointers (locations 103 and 107 hex), and a Selective Message
Monitor Lookup Table (locations 0280 through 02FF hex).
TABLE 45. TYPICAL SELECTIVE MESSAGE MONITOR MEMORY
TABLE 44. MONITOR SELECTION TABLE LOOKUP ADDRESS
MAP (shown for 4K RAM for “Monitor only” mode)
BIT
DESCRIPTION
ADDRESS
DESCRIPTION
(HEX)
15(MSB)
Logic “0”
Logic “0”
14
Not Used
Monitor Command Stack Pointer A (fixed location)
Monitor Data Stack Pointer A (fixed location)
Not Used
0000-0101
0102
13
Logic “0”
12
Logic “0”
0103
11
Logic “0”
0104-0105
0106
Monitor Command Stack Pointer B (fixed location)
Monitor Data Stack Pointer B (fixed location)
Not Used
10
Logic “0”
0107
9
Logic “1”
0108-027F
0280-02FF
0300-03FF
0400-07FF
0800-0FFF
8
Logic “0”
Selective Monitor Lookup Table (fixed location)
Not Used
7
Logic “1”
6
RTAD_4
Monitor Command Stack A
5
RTAD_3
Monitor Data Stack A
4
RTAD_2
3
RTAD_1
For this example, the Monitor Command Stack size is assumed
to be 1K words, and the Monitor Data Stack size is assumed to
be 2K words.
2
RTAD_0
1
TRANSMIT / RECEIVE
SUBADDRESS 4
0(LSB)
FIGURE 11 illustrates the Selective Message Monitor operation.
Upon receipt of a valid Command Word, the Enhanced Mini-ACE
will reference the Selective Monitor Lookup Table to determine if
the current command is enabled. If the current command is dis-
abled, the Enhanced Mini-ACE monitor will ignore (and not store)
the current message. If the command is enabled, the monitor will
create an entry in the Monitor Command Stack at the address
location referenced by the Monitor Command Stack Pointer, and
an entry in the monitor data stack starting at the location refer-
enced by the Monitor Data Stack Pointer.
The format of the information in the data stack depends on the
format of the message that was processed. For example, for a
BC-to-RT transfer (receive command), the monitor will store the
command word in the monitor command descriptor stack, with
the data words and the receiving RT's status word stored in the
monitor data stack.
The size of the monitor command stack is programmable, with
choices of 256, 1K, 4K, or 16K words. The monitor data stack
size is programmable with choices of 512, 1K, 2K, 4K, 8K, 16K,
32K or 64K words.
31
Monitor Interrupts. Selective monitor interrupts may be issued
for End-of-message and for conditions relating to the monitor
command stack pointer and monitor data stack pointer. The lat-
ter, which are shown in FIGURE 9, include Command Stack 50%
Rollover, Command Stack 100% Rollover, Data Stack 50%
Rollover, and Data Stack 100% Rollover.
MISCELLANEOUS
CLOCK INPUT
The Enhanced Mini-ACE decoder is capable of operating from a
10, 12, 16, or 20 MHz clock input. Depending on the configura-
tion of the specific model Enhanced Mini-ACE terminal, the
selection of the clock input frequency may be chosen by one of
either two methods. For all versions, the clock frequency may be
specified by means of the host processor writing to Configuration
Register #6.With the second method, which is applicable only for
the versions incorporating 4K (but not 64K) words of internal
RAM, the clock frequency may be specified by means of the
input signals that are otherwise used as the A15 and A14
address lines.
The 50% rollover interrupts may be used to inform the host
processor when the command stack or data stack is half full. At
that time, the host may proceed to read the received messages
in the upper half of the respective stack, while the Enhanced
Mini-ACE monitor writes messages to the lower half of the stack.
Later, when the monitor issues a 100% stack rollover interrupt,
the host can proceed to read the received data from the lower
half of the stack, while the Enhanced Mini-ACE monitor contin-
ues to write received data words to the upper half of the stack.
ENCODER/DECODERS
For the selected clock frequency, there is internal logic to derive
the necessary clocks for the Manchester encoder and decoders.
For all clock frequencies, the decoders sample the receiver out-
puts on both edges of the input clock. By in effect doubling the
decoders' sampling frequency, this serves to widen the tolerance
to zero-crossing distortion, and reduce the bit error rate.
INTERRUPT STATUS QUEUE
Like the Enhanced Mini-ACE RT, the Selective Monitor mode
includes the capability for generating an interrupt status queue.
As illustrated in FIGURE 10, this provides a chronological histo-
ry of interrupt generating events. Besides the two Interrupt Mask
Registers, the Interrupt Status Queue provides additional filter-
ing capability, such that only valid messages and/or only invalid
messages may result in entries to the Interrupt Status Queue.
The interrupt status queue is 64 words deep, providing the capa-
bility to store entries for up to 32 monitored messages.
For interfacing to fiber optic transceivers (e.g., for MIL-STD-1773
applications), the decoders are capable of operating with single-
ended, rather than double-ended, input signals. For applications
involving the use of single-ended transceivers, it is suggested
that you contact the factory at DDC regarding a transceiverless
version of the Enhanced Mini-ACE.
CONFIGURATION
REGISTER #1
MONITOR COMMAND
STACK POINTERS
MONITOR
COMMAND STACKS
MONITOR DATA
STACKS
15
13
0
CURRENT
AREA B/A
BLOCK STATUS WORD
TIME TAG WORD
MONITOR DATA
BLOCK #N
CURRENT
COMMAND WORD
DATA BLOCK POINTER
MONITOR DATA
BLOCK #N + 1
RECEIVED COMMAND
WORD
MONITOR DATA
STACK POINTERS
NOTE
IF THIS BIT IS "0" (NOT SELECTED)
NO WORDS ARE STORED IN EITHER
THE COMMAND STACK OR DATA STACK.
IN ADDITION, THE COMMAND AND DATA
STACK POINTERS WILL NOT BE UPDATED.
SELECTIVE MONITOR
LOOKUP TABLES
OFFSET BASED ON
RTA4-RTA0, T/R, SA4
SELECTIVE MONITOR
ENABLE
(SEE NOTE)
FIGURE 11. SELECTIVE MESSAGE MONITOR MEMORY MANAGEMENT
32
TIME TAG
Rollover, BC Message, RT Subaddress, BC End-of-Frame,
Format Error, BC Status Set, RT Mode Code, MT Trigger, and
End-of-Message.
The Enhanced Mini-ACE includes an internal read/writable Time
Tag Register. This register is a CPU read/writable 16-bit counter
with a programmable resolution of either 2, 4, 8, 16, 32, or 64 µs
per LSB. Another option allows software controlled incrementing
of the Time Tag Register. This supports self-test for the Time Tag
Register. For each message processed, the value of the Time
Tag Register is loaded into the second location of the respective
descriptor stack entry ("TIME TAG WORD") for both the BC and
RT modes.
For the Enhanced Mini-ACE's Enhanced BC mode, there are
four user-defined interrupt bits. The BC Message Sequence
Control Engine includes an instruction enabling it to issue these
interrupts at any time.
For RT and Monitor modes, the Enhanced Mini-ACE architecture
include an Interrupt Status Queue. This provides a mechanism
for logging messages that result in interrupt requests. Entries to
the Interrupt Status Queue may be filtered such that only valid
and/or invalid messages will result in entries on the queue.
The functionality involving the Time Tag Register that's compati-
ble with ACE/Mini-ACE (Plus) includes: the capability to issue an
interrupt request and set a bit in the Interrupt Status Register
when the Time Tag Register rolls over FFFF to 0000; for RT
mode, the capability to automatically clear the Time Tag Register
following reception of a Synchronize (without data) mode com-
mand, or to load the Time Tag Register following a Synchronize
(with data) mode command.
The Enhanced Mini-ACE incorporates additional interrupt condi-
tions beyond ACE/Mini-ACE (Plus), based on the addition of
Interrupt Mask Register #2 and Interrupt Status Register #2.This
is accomplished by chaining the two Interrupt Status Registers
using the INTERRUPT CHAIN BIT (bit 0) in Interrupt Status
Register #2 to indicate that an interrupt has occurred in Interrupt
Status Register #1. Additional interrupts include "Self-Test
Completed", masking bits for the Enhanced BC Control
Interrupts, 50% Rollover interrupts for RT Command Stack, RT
Circular Buffers, MT Command Stack, and MT Data Stack; BC
Op Code Parity Error, (RT) Illegal Command, (BC) General
Purpose Queue or (RT/MT) Interrupt Status Queue Rollover,
Call Stack Pointer Register Error, BC Trap Op Code, and the four
User-Defined interrupts for the Enhanced BC mode.
Additional time tag features supported by the Enhanced Mini-
ACE include the capability for the BC to transmit the contents of
the Time Tag Register as the data word for a Synchronize (with
data) mode command; the capability for the RT to "filter" the data
word for the Synchronize with data mode command, by only
loading the Time Tag Register if the LSB of the received data
word is "0"; an instruction enabling the BC Message Sequence
Control engine to load the Time Tag Register with a specified
value; and an instruction enabling the BC Message Sequence
Control engine to write the value of the Time Tag Register to the
General Purpose Queue.
BUILT-IN TEST
A salient feature of the Enhanced Mini-ACE is its highly
autonomous self-test capability. This includes both protocol and
RAM self-tests. Either or both of these self-tests may be initiated
by command(s) from the host processor.
INTERRUPTS
The Enhanced Mini-ACE series terminals provide many pro-
grammable options for interrupt generation and handling. The
INT
interrupt output pin (
) has three software programmable
mode of operation: a pulse , a level output cleared under soft-
ware control, or a level output automatically cleared following a
read of the Interrupt Status Register (#1 or #2).
The protocol test consists of a toggle test of 95% of the termi-
nal's logic gates. The test includes a comprehensive test of all
registers, Manchester encoder and decoders, transmitter failsafe
timer, and protocol logic. This test is completed in approximately
32,000 clock cycles. That is, about 1.6 ms with a 20 MHz clock,
2.0 ms at 16 MHz, 2.7 ms at 12 MHz, and 3.2 ms at 10 MHz.
Individual interrupts are enabled by the two Interrupt Mask
Registers. The host processor may determine the cause of the
interrupt by reading the two Interrupt Status Registers, which
provide the current state of interrupt events and conditions. The
Interrupt Status Registers may be updated in two ways. In one
interrupt handling mode, a particular bit in Interrupt Status
Register #1 or #2 will be updated only if the event occurs and the
corresponding bit in Interrupt Mask Register #1 or #2 is enabled.
In the enhanced interrupt handling mode, a particular bit in the
one of the Interrupt Status Registers will be updated if the
event/condition occurs regardless of the value of the corre-
sponding Interrupt Mask Register bit. In either case, the respec-
tive Interrupt Mask Register (#1 or #2) bit is used to enable an
interrupt for a particular event/condition.
There is also a separate built-in test for the Enhanced Mini-
ACE's 4K X 16 or 64K X 16 shared RAM. This test consists of
writing and then reading/verifying the two walking patterns "data
= address" and "data = address inverted". This test takes 10
clock cycles per word. For an Enhanced Mini-ACE with 4K words
of RAM, this is about 2.0 ms with a 20 MHz clock, 2.6 ms at 16
MHz, 3.4 ms at 12 MHz, or 4.1 ms at 10 MHz. For an Enhanced
Mini-ACE with 64K words of RAM, this test takes about 32.8 ms
with a 20 MHz clock, 40.1 ms at 16 MHz, 54.6 ms at 12 MHz, or
65.6 ms at 10 MHz.
The Enhanced Mini-ACE built-in test may be initiated by a com-
mand from the host processor, via the START/REST REGIS-
TER. For RT mode, this may include the host processor invoking
self-test following receipt of an Initiate self-test mode command.
The results of the self-test are host accessible by means of the
BIT status register. For RT mode, the result of the self-test may
The Enhanced Mini-ACE supports all the interrupt events from
ACE/Mini-ACE (Plus), including RAM Parity Error, Transmitter
Timeout, BC/RT Command Stack Rollover, MT Command Stack
and Data Stack Rollover, Handshake Error, BC Retry, RT
Address Parity Error, Time Tag Rollover, RT Circular Buffer
33
be communicated to the bus controller via bit 8 of the RT BIT
word ("0" = pass, "1" = fail).
HOST PROCESSOR INTERFACE
The Enhanced Mini-ACE supports a wide variety of processor
interface configurations. These include shared RAM and DMA
configurations, straightforward interfacing for 16-bit and 8-bit
buses, support for both non-multiplexed and multiplexed
address/data buses, non-zero wait mode for interfacing to a
processor address/data buses, and zero wait mode for interfac-
ing (for example) to microcontroller I/O ports. In addition, with
respect to the ACE/Mini-ACE, the Enhanced Mini-ACE provides
two major improvements: (1) reduced maximum host access
time for shared RAM mode; and (2) increased maximum DMA
grant time for the transparent/DMA mode.
Assuming that the protocol self-test passes, all of the register
and shared RAM locations will be restored to their state prior to
the self-test, with the exception of the 60 RAM address locations
0342-037D and the TIME TAG REGISTER. Note that for RT
mode, these locations map to the illegalization lookup table for
"broadcast transmit subaddresses 1 through 30" (non-mode
code subaddresses). Since MIL-STD-1553 does not define
these as valid command words, this section of the illegalization
lookup table is normally not used.The TIME TAG REGISTER will
continue to increment during the self-test.
If there is a failure of the protocol self-test, it is possible to access
information about the first failed vector. This may be done by
means of the Enhanced Mini-ACE's upper registers (register
addresses 32 through 63). Through these registers, it is possible
to determine the self-test ROM address of the first failed vector,
the expected response data pattern (from the ROM), the register
or memory address, and the actual (incorrect) data value read
from register or memory. The on-chip self-test ROM is 4K X 24.
The Enhanced Mini-ACE's maximum host holdoff time (time prior
READYD
to the assertion of the
handshake signal) has been sig-
nificantly reduced. For ACE/Mini-ACE, this maximum holdoff
time is 10 internal word transfer cycles, resulting in an overall
holdoff time of approximately 2.8 µs, using a 16 MHz clock. By
comparison, using the Enhanced Mini-ACE's ENHANCED CPU
ACCESS feature, this worst-case holdoff time is reduced signifi-
cantly, to a single internal transfer cycle. For example, when
operating the Enhanced Mini-ACE in its 16-bit buffered, non-zero
wait configuration with a 16 MHz clock input, this results in a
maximum overall host transfer cycle time of 632 ns for a read
cycle, or 570 ns for a write cycle.
Note that the RAM self-test is destructive. That is, following the
RAM self-test, regardless of whether the test passes or fails, the
shared RAM is not restored to its state prior to this test.
Following a failed RAM self-test, the host may read the internal
RAM to determine which location(s) failed the walking pattern
test.
In addition, for using the ACE or Mini-ACE in the
transparent/DMA configuration, the maximum request-to-grant
time, which occurs prior to an RT start-of-message sequence, is
4.0 µs with a 16 MHz clock, or 3.5 µs with a 12 MHz clock. For
the Enhanced Mini-ACE functioning as a MIL-STD-1553B RT,
this time has been increased to 8.5 µs at 10 MHz, 10 µs at 16
MHz, 9 µs at 12 MHz, and 10.5 µs at 20MHz. This provides
greater flexibility, particularly for systems in which a host has to
arbitrate among multiple DMA requestors.
RAM PARITY
The BC/RT/MT version of the Enhanced Mini-ACE is available
with options of 4K or 64K words of internal RAM. For the 64K
option, the RAM is 17 bits wide. The 64K X 17 internal RAM
allows for parity generation for RAM write accesses, and parity
checking for RAM read accesses.This includes host RAM acess-
es, as well as acesses by the Enhanced Mini-ACE’s internal
logic. When the Enhanced Mini-ACE detects a RAM parity error,
it reports it to the host processor by means of an interrupt and a
register bit. Also, for the RT and Selective Message Monitor
modes, the RAM address where a parity error was detected will
be stored on the Interrupt Status Queue (if enabled).
By far, the most commonly used processor interface configura-
tion is the 16-bit buffered, non-zero wait mode.This configuration
may be used to interface between 16-bit or 32-bit microproces-
sors and an Enhanced Mini-ACE. In this mode, only the
Enhanced Mini-ACE's internal 4K or 64K words of internal RAM
are used for storing 1553 message data and associated "house-
keeping" functions. That is, in this configuration, the Enhanced
Mini-ACE will never attempt to access memory on the host bus.
RELOCATABLE MEMORY MANAGEMENT LOCATIONS
In the Enhanced Mini-ACE's default configuration, there is a fixed
area of shared RAM addresses, 0000h-03FF, that is allocated for
storage of the BC's or RT's pointers, counters, tables, and other
"non-message" data structures. As a means of reducing the
overall memory address space for using multiple Enhanced Mini-
ACEs in a given system (e.g., for use with the DMA interface
configuration), the Enhanced Mini-ACE allows this area of RAM
to be relocated by means of 6 configuration register bits. To pro-
vide backwards compatibility to ACE and Mini-ACE, the default
for this RAM area is 0000h-03FFh.
FIGURE 12 illustrates a generic connection diagram between a
16-bit (or 32-bit) microprocessor and an Enhanced Mini-ACE for
the 16-bit buffered configuration, while Figures 13 and 14, and
associated tables illustrate the processor read and write timing
respectively.
34
+5V (3.3V)
(NOTE 5)
CLK IN
CLOCK
OSCILLATOR
D15-D0
A15-A12
A11-A0
55 Ω
TX/RXA
N/C
CH. A
TX/RXA
55 Ω
ADDR_LAT
(NOTE 1)
CPU ADDRESS LATCH
TRANSPARENT/BUFFERED
+5V
16/8_BIT
55 Ω
TRIGGER_SEL
+5V
TX/RXB
TX/RXB
N/C
N/C
MSB/LSB
CH. B
POLARITY_SEL
(NOTE 2)
Enhanced
Mini-ACE
ZERO_WAIT
(NOTE 3)
HOST
55 Ω
SELECT
ADDRESS
DECODER
MEM/REG
RD/WR
RD/WR
STRBD
CPU STROBE
RTAD4-RTAD0
RT
ADDRESS,
PARITY
CPU ACKNOWLEDGE
READYD
TAG_CLK
(NOTE 4)
RTADP
+5V
RESET
MSTCLR
SSFLAG/EXT_TRIG
INT
CPU INTERRUPT REQUEST
NOTES:
1. CPU ADDRESS LATCH SIGNAL PROVIDED BY
3. ZERO_WAIT SHOULD BE STRAPPED TO
LOGIC "1" FOR NON-ZERO WAIT INTERFACE
AND TO LOGIC "0" FOR ZERO WAIT INTERFACE.
4. CPU ACKNOWLEDGE PROCESSOR INPUT ONLY
FOR NON-ZERO WAIT TYPE OF INTERFACE.
PROCESSORS WITH MULTIPLEXED ADDRESS/DATA
BUSES. FOR PROCESSORS WITH NON-MULTIPLEXED
ADDRESS AND DATA BUSSES, ADDR_LAT SHOULD BE
CONNECTED TO +5V.
2. IF POLARITY_SEL = "1", RD/WR IS HIGH TO READ,
LOW TO WRITE.
5. +3.3V POWER FOR BU-61743 / 61843 / 61864 ONLY
IF POLARITY_SEL = "0", RD/WR IS LOW TO READ,
HIGH TO WRITE.
FIGURE 12. HOST PROCESSOR INTERFACE - 16-BIT BUFFERED CONFIGURATION
35
t5
CLOCK IN
t1
SELECT
(Note 2,7)
t6
t2
t18
t14
STRBD
(Note 2)
VALID
MEM/REG
(Note 3,4,7)
t7
t8
t3
RD/WR
(Note 4,5)
t11
IOEN
(Note 2,6)
t15
t13
READYD
t4
(Note 6)
t12
t9
t19
t10
VALID
A15-A0
(Note 7,8,9)
t16
VALID
D15-D0
(Note 6)
t17
FIGURE 13. CPU READING RAM / REGISTER (16-BIT BUFFERED, NONZERO WAIT)
NOTES:
TRANSPARENT /BUFFERED
ZERO WAIT
1. For the 16-bit buffered nonzero wait configuration,
DTREQ/16/8
must be connected to logic "0".
and
must be connected to logic "1". The inputs TRIGGER_SEL and MSB/LSB may be connected to either +5V or ground.
SELECT
STRBD
IOEN
SELECT STRBD
goes low on the first rising CLK edge when • is sampled low (satisfying t1)
2.
and
may be tied together.
IOEN
and the Enhanced Mini-ACE's protocol/memory management logic is not accessing the internal RAM. When this occurs,
IOEN SELECT
goes low, start-
ing the transfer cycle. After
goes low,
may be released high.
MEM/REG
MEM/REG
3.
4.
must be presented high for memory access, low for register access.
RD/ WR
IOEN
goes low. After this CLK edge,
MEM/REG
and
and
are buffered transparently until the first falling edge of CLK after
RD/ WR
become latched internally.
RD/ WR
5. The logic sense for
in the diagram assumes that POLARITY_SEL is connected to logic "1." If POLARITY_SEL is connected to logic "0,"
RD/ WR
must be asserted low to read.
IOEN
READYD
READYD
, and D15-D0 is
IOEN
6. The timing for
,
and D15-D0 assumes a 50 pf load. For loading above 50 pf, the validity of
,
delayed by an additional 0.14 ns/pf typ, 0.28 ns/pf max.
MEM/REG
SELECT
assumes that ADDR-LAT is connected to logic "1." Refer to Address Latch timing for additional
7. The timing for A15-A0,
details.
and
IOEN
8. The address bus A15-A0 is internally buffered transparently until the first rising edge of CLK after
become latched internally.
goes low. After this CLK edge, A15-A0
9. Setup time given for use in worst case timing calculations. None of the Enhanced Mini-ACE input signals are required to be synchronized to the
SELECT STRBD
system clock. When
tional clock cycle will be inserted between the falling clock edge that latches
and
do not meet the setup time of t1, but occur during the setup window of an internal flip-flop, an addi-
RD/ WR
MEM/REG
and
READYD
falling (t11) increases by one clock cycle and the address hold
and the rising clock edge that latches the
IOEN
Address (A15-A0). When this occurs, the delay from
time (t10) must be increased be one clock cycle.
falling to
36
TABLE FOR FIGURE 13. CPU READING RAM OR REGISTERS (SHOWN FOR 16-BIT, BUFFERED, NONZERO WAIT MODE)
5V LOGIC
3.3V LOGIC
REF
DESCRIPTION
NOTES
UNITS
MIN TYP MAX MIN TYP MAX
t1 SELECT and STRBD low setup time prior to clock rising edge
2, 9
10
15
ns
t2
SELECT and STRBD low to IOEN low (uncontended access @ 20 MHz)
2, 6
2, 6
2, 6
2, 6
2, 6
2, 6
2, 6
2, 6
2, 6
2, 6
2, 6
2, 6
100
2.2
105
2.2
ns
µs
ns
ns
µs
ns
ns
µs
ns
ns
µs
ns
(contended access, with ENHANCED CPU SELECT = “0” @ 20 MHz)
(contended access, with ENHANCED CPU SELECT = “1” @ 20 MHz)
(uncontended access @ 16 MHz)
350
112
2.8
355
117
2.8
(contended access, with ENHANCED CPU SELECT = “0” @ 16 MHz)
(contended acces, with ENHANCED CPU SELECT = “1” s @ 16 MHz)
(uncontended access @ 12 MHz)
425
133
3.7
430
138
3.7
(contended access, with ENHANCED CPU SELECT = “0” @ 12 MHz)
(contended access, with ENHANCED CPU SELECT = “1” @ 12 MHz)
(uncontended access @ 10 MHz)
550
150
4.4
555
155
4.4
(contended access, with ENHANCED CPU SELECT = “0” @ 10 MHz)
(contended access, with ENHANCED CPU SELECT = “1” @ 10 MHz)
650
655
t3
Time for MEM/REG and RD/WR to become valid following SELECT and STRBD
low(@ 20 MHz)
3, 4, 5, 7
3, 4, 5, 7
3, 4, 5, 7
3, 4, 5, 7
15
21
32
40
10
16
27
35
ns
ns
ns
ns
@ 16 MHz
@ 12 MHz
@ 10 MHz
t4
Time for Address to become valid following SELECT and STRBD low (@ 20 MHz)
17
30
50
67
12
25
45
62
ns
ns
ns
ns
@ 16 MHz
@ 12 MHz
@ 10 MHz
t5 CLOCK IN rising edge delay to IOEN falling edge
t6 SELECT hold time following IOEN falling
6
2
40
40
ns
ns
ns
ns
ns
ns
0
0
t7 MEM/REG, RD/WR setup time prior to CLOCK IN falling edge
t8 MEM/REG, RD/WR hold time following CLOCK IN falling edge
t9 Address valid setup time prior to CLOCK IN rising edge
t10 Address hold time following CLOCK IN rising edge
3, 4, 5, 7 10
3, 4, 5, 7 30
15
30
35
30
7, 8
30
30
7, 8, 9
t11
IOEN falling delay to READYD falling (@ 20 MHz)
6, 9
6, 9
6, 9
6, 9
135 150 165 135 150 165
170 187.5 205 170 187.5 205
235 250 265 235 250 265
285 300 315 285 300 315
ns
ns
ns
ns
@ 16 MHz
@ 12 MHz
@ 10 MHz
t12
Output Data valid prior to READYD falling (@ 20 MHz)
6
6
6
6
21
33
54
71
11
23
44
61
ns
ns
ns
ns
@ 16 MHz
@ 12 MHz
@ 10 MHz
t13 CLOCK IN rising edge delay to READYD falling
t14 READYD falling to STRBD rising release time
t15 STRBD rising edge delay to IOEN rising edge and READYD rising edge
t16 Output Data hold time following STRBD rising edge
t17 STRBD rising delay to output data tri-state
6
40
∞
40
∞
ns
ns
ns
ns
ns
ns
ns
6
30
40
0
0
0
0
40
40
40
40
t18 STRBD high hold time from READYD rising
t19 CLOCK IN rising edge delay to output data valid
37
t6
CLOCK IN
t1
SELECT
(Note 2,7)
t7
t16
t2
t18
STRBD
(Note 2)
VALID
MEM/REG
(Note 3,4,7)
t8
t9
t3
RD/WR
(Note 4,5)
t14
IOEN
(Note 2,6)
t15
t17
READYD
t4
t5
(Note 6)
t10
t12
t13
VALID
A15-A0
(Note 7,8,9,10)
t11
VALID
D15-D0
(Note 9,10)
FIGURE 14. CPU WRITING RAM / REGISTER (16-BIT BUFFERED, NONZERO WAIT)
NOTES:
TRANSPARENT /BUFFERED
ZERO WAIT
1. For the 16-bit buffered nonzero wait configuration
must be connected to logic "0",
and
DTREQ/16/8
must be connected to logic "1". The inputs TRIGGER_SEL and MSB/LSB may be connected to either +5V or ground.
SELECT
STRBD
IOEN
SELECT STRBD
goes low on the first rising CLK edge when • is sampled low (satisfying
2.
and
may be tied together.
IOEN
t1) and the Enhanced Mini-ACE's protocol/memory management logic is not accessing the internal RAM. When this occurs,
IOEN SELECT
goes low, start-
ing the transfer cycle. After
goes low,
may be released high.
MEM/REG
MEM/REG
3.
4.
must be presented high for memory access, low for register access.
MEM/REG
and
IOEN
and RD/ WR are buffered transparently until the first falling edge of CLK after
become latched internally.
goes low. After this CLK edge,
RD/ WR
5. The logic sense for RD/ WR in the diagram assumes that POLARITY_SEL is connected to logic "1." If POLARITY_SEL is connected to logic "0,"
RD/ WR must be asserted high to write.
READYD
READYD
is delayed
IOEN
IOEN
and
6. The timing for the
and
outputs assumes a 50 pf load. For loading above 50 pf, the validity of
by an additional 0.14 ns/pf typ, 0.28 ns/pf max.
MEM/REG
SELECT
assumes that ADDR-LAT is connected to logic "1." Refer to Address Latch timing for addi-
7. The timing for A15-A0,
tional details.
, and
IOEN
9. The address bus A15-A0 and data bus D15-D0 are internally buffered transparently until the first rising edge of CLK after
this CLK edge, A15-A0 and D15-D0 become latched internally.
goes low. After
10. Setup time given for use in worst case timing calculations. None of the Enhanced Mini-ACE input signals are required to be synchronized to the
SELECT STRBD
do not meet the setup time of t1, but occur during the setup time of an internal flip-flop, an addition-
system clock. When
and
RD/ WR
MEM/REG
al clock cycle may be inserted between the falling clock edge that latches
and
READYD
falling to
and the rising clock edge that latches the
falling (t14) increases by one clock cycle and
IOEN
address (A15-A0) and data (D15-D0). When this occurs, the delay from
the address and data hold time (t12 and t13) must be increased by one clock.
38
TABLE FOR FIGURE 14. CPU WRITING RAM OR REGISTERS (SHOWN FOR 16-BIT, BUFFERED, NONZERO WAIT MODE)
5V LOGIC
3.3V LOGIC
REF
DESCRIPTION
NOTES
UNITS
MIN TYP MAX MIN TYP MAX
t1 SELECT and STRBD low setup time prior to clock rising edge
2, 10
10
15
ns
t2
SELECT and STRBD low to IOEN low (uncontended access @ 20 MHz)
2, 6
2, 6
2, 6
2, 6
2, 6
2, 6
2, 6
2, 6
2, 6
2, 6
2, 6
2, 6
100
2.2
105
2.2
ns
µs
ns
ns
µs
ns
ns
µs
ns
ns
µs
ns
(contended access, with ENHANCED CPU SELECT = “0” @ 20 MHz)
(contended access, with ENHANCED CPU SELECT = “1” @ 20 MHz)
(uncontended access @ 16 MHz)
350
112
2.8
355
117
2.8
(contended access, with ENHANCED CPU SELECT = “0” @ 16 MHz)
(contended acces, with ENHANCED CPU SELECT = “1” @ 16 MHz)
(uncontended access @ 12 MHz)
425
133
3.7
430
138
3.7
(contended access, with ENHANCED CPU SELECT = “0” @ 12 MHz)
(contended access, with ENHANCED CPU SELECT = “1” @ 12 MHz)
(uncontended access @ 10 MHz)
550
150
4.4
555
155
4.4
(contended access, with ENHANCED CPU SELECT = “0” @ 10 MHz)
(contended access, with ENHANCED CPU SELECT = “1” @ 10 MHz)
650
655
t3
Tme for MEM/REG and RD/WR to become valid following SELECT and STRBD
low(@ 20 MHz)
3, 4, 5, 7
3, 4, 5, 7
3, 4, 5, 7
3, 4, 5, 7
15
21
32
40
10
16
27
35
ns
ns
ns
ns
@ 16 MHz
@ 12 MHz
@ 10 MHz
t4
Time for Address to become valid following SELECT and STRBD low (@ 20 MHz)
17
30
50
67
12
25
45
62
ns
ns
ns
ns
@ 16 MHz
@ 12 MHz
@ 10 MHz
t5
Time for data to become valid following SELECT and STRBD low ( @ 20 MHz )
37
50
70
87
40
32
45
65
82
40
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
@ 16 MHz
@ 12 MHz
@ 10 MHz
t6 CLOCK IN rising edge delay to IOEN falling edge
t7 SELECT hold time following IOEN falling
t8 MEM/REG, RD/WR setup time prior to CLOCK IN falling edge
t9 MEM/REG, RD/WR setup time following CLOCK IN falling edge
t10 Address valid setup time prior to CLOCK IN rising edge
t11 Data valid setup time prior to CLOCK IN rising edge
t12 Address valid hold time prior to CLOCK IN rising edge
t13 Data valid hold time following CLOCK IN rising edge
6
2
0
0
3, 4, 5, 7
3, 4, 5, 7
7, 8
10
30
30
10
30
10
15
35
35
15
30
15
7, 8, 9
9
t14
IOEN falling delay to READYD falling @ 20 MHz
6, 9
6, 9
6, 9
6, 9
6
85
100 115 85 100 115
ns
ns
ns
ns
ns
ns
ns
ns
@ 16 MHz
110 125 140 110 125 140
152 167 182 152 167 182
185 200 215 185 200 215
@ 12 MHz
@ 10 MHz
t15 CLOCK IN rising edge delay to READYD falling
t16 READYD falling to STRBD rising release time
t17 STRBD rising delay to IOEN rising edge and READYD rising edge
t18 STRBD high hold time from READYD rising
40
∞
40
∞
6
30
40
0
0
39
INTERFACE TO MIL-STD-1553 BUS
FIGURE 15 illustrates the interface between the various versions
of the Enhanced Mini-ACE series and a MIL-STD-1553 bus.
Connections for both direct (short stub) and transformer (long
stub) coupling, as well as the nominal peak-to-peak voltage lev-
els at various points (when transmitting), are indicated in the dia-
gram.
DATA
BUS
Z0
SHORT STUB
(DIRECT COUPLED)
(1:2.5)
1 FT MAX
55 Ω
TX/RX
11.6 Vpp
TX/RX
7 Vpp
28 Vpp
Enhanced
MINI-ACE
55 Ω
ISOLATION
TRANSFORMER
LONG STUB
(TRANSFORMER
COUPLED)
OR
(1:1.79)
(1:1.14)
0.75 Z0
28 Vpp
20 FT MAX
20 Vpp
11.6 Vpp
7 Vpp
0.75 Z0
COUPLING
TRANSFORMER
ISOLATION
TRANSFORMER
Z0
NOTE: Z 0 = 70 TO 85 OHMS
FIGURE 15. ENHANCED MINI-ACE INTERFACE TO MIL-STD-1553 BUS
40
TRANSFORMERS
side of the primary is shorted to the primary center-tap, the
inductance measured accross the “secondary” (stub side) wind-
ing must also be less than 6.0 µH.
In selecting isolation transformers to be used with the Enhanced
Mini-ACE, there is a limitation on the maximum amount of leak-
age inductance. If this limit is exceeded, the transmitter rise and
fall times may increase, possibly causing the bus amplitude to fall
below the minimum level required by MIL-STD-1553. In addition,
an excessive leakage imbalance may result in a transformer
dynamic offset that exceeds 1553 specifications.
The difference between these two measurements is the
“differential” leakage inductance. This value must be less than
1.0 µH.
Beta Transformer Technology Corporation (BTTC), a subsidiary
of DDC, manufactures transformers in a variety of mechanical
configurations with the required turns ratios of 1:2.5 direct cou-
pled, and 1:1.79 transformer coupled. TABLE 46 provides a list-
ing of many of these transformers.
The maximum allowable leakage inductance is 6.0 µH, and
is measured as follows:
The side of the transformer that connects to the Enhanced
Mini-ACE is defined as the “primary” winding. If one side of the
primary is shorted to the primary center-tap, the inductance
should be measured across the “secondary” (stub side) winding.
This inductance must be less tha 6.0 µH. Similarly, if the other
For further information, contact BTTC at 631-244-7393 or at
www.bttc-beta.com.
NOTES:
1. For the BU-6XXXXX4 versions of the Enhanced Mini-ACE, which include the McAir-compatible transceivers, only the B-3818 or B-3819 trans-
formers (shown in bold in the table) may be used.
2. For the BU-6XXXXX3 versions of the Enhanced Mini-ACE with -1553B transceivers, any of the transformers listed in the table may be used.
TABLE 46. BTTC TRANSFORMERS FOR USE WITH ENHANCED MINI-ACE
TRANSFORMER CONFIGURATION
BTTC PART NO.
Single epoxy transformer, through-hole, 0.625 X 0.625, 0.250" max height
B-3226
Single epoxy transformer, through-hole, 0.625 X 0.625, 0.220" max height.
May be used with BU-6XXXXX4 versions of the Enhanced Mini-ACE.
B-3818
B-3231
Single epoxy transformer, flat pack, 0.625" X 0.625", 0.275" max height
Single epoxy transformer, surface mount, 0.625" X 0.625", 0.275" max height
B-3227
Single epoxy transformer, surface mount, hi-temp solder, 0.625" X 0.625", 0.220" max height.
May be used with BU-6XXXXX4 versions of the Enhanced Mini-ACE.B-3819
B-3819
Single epoxy transformer, flat pack, 0.625" X 0.625", 0.150" max height
Single epoxy transformer, surface mount, 0.625" X 0.625", 0.150" max height
LPB-5014
LPB-5015
TST-9007
TST-9017
TST-9027
B-3300
Dual epoxy transformer, twin stacked, 0.625" X 0.625", 0.280" max height
Dual epoxy transformer, twin stacked, surface mount, 0.625" X 0.625", 0.280" max height
Dual epoxy transformer, twin stacked, flat pack, 0.625" X 0.625", 0.280" max height
Dual epoxy transformer, side by side, through-hole, 0.930" X 0.630", 0.155 max height
Dual epoxy transformer, side by side, flat pack, 0.930" X 0.630", 0.155 max height
Dual epoxy transformer, side by side, surface mount, 0.930" X 0.630", 0.155 max height
Single metal transformer, hermetically sealed, flat pack, 0.630" X 0.630", 0.175" max height
Single metal transformer, hermetically sealed, surface mount, 0.630" X 0.630", 0.175" max height
B-3261
B-3310
HLP-6014
HLP-6015
41
TABLE 47. SIGNAL DESCRIPTIONS BY FUNCTIONAL GROUPS
POWER AND GROUND
SIGNAL NAME
BU-61864(5)
(64K RAM)
BU-61843(5) /
61743(5)
DESCRIPTION
(4KK RAM)
PIN
72
PIN
72
+5V Vcc CH A
+5V Vcc CH B
+5V / +3.3V Logic
Channel A transceiver power.
Channel B transceiver power.
20
20
37
37
Logic power. For BU-61864/61843/61743, this pin must be connected to +3.3V.
For BU-61865/61845/61745, this pin must be connected to +5V.
+5V RAM
GROUND
26
-
For BU-61864 or BU-61865, this pin must be connected to +5V.
Note that for BU-6184X/6174X, this pin assumes the function UPADDREN.
17
18
19
65
67
17
18
19
65
67
Ground.
1553 ISOLATION TRANSFORMER INTERFACE (4)
DESCRIPTION
SIGNAL NAME PIN
Analog Transmit/Receive Input/Outputs. Connect directly to 1553 isolation transformers.
TX/RX-A (I/O)
TX/RX-A (I/O)
TX/RX-B (I/O)
TX/RX-B (I/O)
5
7
13
16
DATA BUS (16)
DESCRIPTION
SIGNAL NAME PIN
D15 (MSB)
D14
D13
D12
D11
D10
D9
53 16-bit bi-directional data bus. This bus interfaces the host processor to the Enhanced Mini-ACE's internal registers and
internal RAM. In addition, in transparent mode, this bus allows data transfers to take place between the internal proto-
col/memory management logic and up to 64K x 16 of external RAM. Most of the time, the outputs for D15 through D0 are
50
48 in the high impedance state. They drive outward in the buffered or transparent mode when the host CPU reads the inter-
nal RAM or registers.
49
Also, in the transparent mode, D15-D0 will drive outward (towards the host) when the protocol/management logic is
accessing (either reading or writing) internal RAM, or writing to external RAM. In the transparent mode, D15-D0 drives
inward when the CPU writes internal registers or RAM, or when the protocol/memory management logic reads external
RAM.
52
54
51
46
47
36
45
39
44
43
38
42
D8
D7
D6
D5
D4
D3
D2
D1
D0 (LSB)
42
PROCESSOR ADDRESS BUS
SIGNAL NAME
BU-61843(5) /
PIN
DESCRIPTION
BU-61864(5)
(64K RAM)
61743(5)
(4KK RAM)
A15
A15 / CLK_SEL_1
66 For BU-61864(5) (64K RAM version), this signal is always configured as address line A15 (MSB).
Refer to the description for A11-A0 below.
For BU-61843(5)/61743(5) (4K RAM version), if UPADDREN is connected to logic "1", this signal
operates as address line A15.
For BU-61843(5)/61743(5) (4K RAM version), if UPADDREN is connected to logic "0", this signal
operates as CLK_SEL_1. In this case, A15/CLK_SEL_1 and A14/CLK_SEL_0 are used to select
the Enhanced Mini-ACE's clock frequency, as follows:
Clock
CLK_SEL_1 CLK_SEL_0
Frequency
10 MHz
20 MHz
12 MHz
16 MHz
0
0
1
1
0
1
0
1
A14
A14 / CLK_SEL_0
8
For BU-61864(5) (64K RAM version), this signal is always configured as address line A14. Refer
to the description of A11-A0 below.
For BU-61843(5)/61743(5) (4K RAM version), if UPADDREN is connected to logic "1", this signal
operates as A14.
For BU-61843(5)/61743(5) (4K RAM version), if UPADDREN is connected to logic "0", then this
signal operates as CLK_SEL_1. In this case, CLK_SEL_1 and CLK_SEL_0 are used to select the
Enhanced Mini-ACE's clock frequency, as defined in the description for A15/CLK_SEL1 above.
A13
A13 / Vcc -LOGIC
71 For BU-61864(5) (64K RAM version), this signal is always configured as address line A13. Refer
to the description for A11-A0 below.
For BU-61843(5)/61743(5) (4K RAM version), if UPADDREN is connected to logic "1", this signal
operates as A13.
For BU-61843(5)/61743(5) (4K RAM version), if UPADDREN is connected to logic "0", then
this signal MUST be connected to +5V/+3.3V-LOGIC (logic "1" ).
A12
A12 / RTBOOT
70 For BU-61864(5) (64K RAM version), this signal is always configured as address line A12. Refer
to the description for A11-A0 below.
For BU-61843(5)/61743(5) (4K RAM version), if UPADDREN is connected to logic "1", this signal
operates as A12.
For BU-61843(5)/61743(5) (4K RAM version), if UPADDREN is connected to logic "0", then this
signal functions as RTBOOT. If RTBOOT is connected to logic "0", the Enhanced Mini-ACE will
initialize in RT mode with the Busy status word bit set following power turn-on. If RTBOOT hard-
wired to logic "1", the Enhanced Mini-ACE will initialize in either Idle mode (for an RT-only part), or
in BC mode (for a BC/RT/MT part).
43
PROCESSOR ADDRESS BUS (CONTINUED)
SIGNAL NAME
BU-61843(5) /
PIN
DESCRIPTION
BU-61864(5)
(64K RAM)
61743(5)
(4KK RAM)
A11
A10
A9
A11
A10
A9
3
4
Lower 12 bits of 16-bit bi-directional address bus. In both the buffered and transparent modes,
the host CPU accesses the Enhanced Mini-ACE registers and internal RAM by means of A11 -
A0 (4K version). For the 64K versions, A15 - A12 are also used for this purpose.
69
6
In buffered mode, A12-A0 (or A15-A0) are inputs only. In the transparent mode, A12-A0 (or
A15-A0) are inputs during CPU accesses and become outputs, driving outward (towards the
CPU) when the 1553 protocol/memory management logic accesses up to 64K words of external
RAM.
A8
A8
A7
A6
A7
A6
11
22
68
9
In transparent mode, the address bus is driven outward only when the signal DTACK is low
(indicating that the Enhanced Mini-ACE has control of the RAM interface bus) and IOEN is high,
indicating a non-host access. Most of the time, including immediately after power turn-on, A12-
A0 (or A15-A0) will be in high impedance (input) state.
A5
A5
A4
A4
A3
A3
10
12
27
15
A2
A2
A1
A1
A0(LSB)
A0(LSB)
44
PROCESSOR INTERFACE CONTROL
DESCRIPTION
SIGNAL NAME
PIN
SELECT (1)
61 Generally connected to a CPU address decoder output to select the Enhanced Mini-ACE for a transfer to/from either
RAM or register.
STRBD (1)
RD / WR
62 Strobe Data. Used in conjunction with SELECT to initiate and control the data transfer cycle between the host proces-
sor and the ENHANCED MINI-ACE. STRBD must be asserted low through the full duration of the transfer cycle.
63 Read/Write. For a host processor access, RD/WR selects between reading and writing. In the 16-bit buffered mode, if
POL_SEL is logic "0, then RD/WR should be low (logic “0") for read accesses and high (logic "1") for write accesses. If
POL_SEL is logic "1", or the interface is configured for a mode other than 16-bit buffered mode, then RD/WR is high
(logic "1") for read accesses and low (logic "0") for write accesses.
ADDR_LAT(1) /
MEMOE (0)
14 Memory Output Enable or Address Latch.
In buffered mode, the ADDR_LAT input is used to configure the buffers for A15-A0, SELECT, MEM/REG, and MSB/LSB
(for 8-bit mode only) in latched mode (when low) or transparent mode (when high). That is, the Enhanced Mini-ACE's
internal transparent latches will track the values on A15-A0, SELECT, MEM/REG, and MSB/LSB when ADDR_LAT is
high, and latch the values when ADDR_LAT goes low.
In general, for interfacing to processors with a non-multiplexed address/data bus, ADDR_LAT should be hardwired to
logic "1". For interfacing to processors with a multiplexed address/data bus, ADDR_LAT should be connected to a signal
that indicates a valid address when ADDR_LAT is logic "1".
In transparent mode, MEMOE output signal is used to enable data outputs for external RAM read cycles (normally con-
nected to the OE input signal on external RAM chips).
ZEROWAIT (1) /
MEMWR (0)
23 Memory Write or Zero Wait . In buffered mode, input signal (ZEROWAIT) used to select between the zero wait mode
(ZEROWAIT = “0") and the non-zero wait mode (ZEROWAIT = "1").
In transparent mode, active low output signal (MEMWR) asserted low during memory write transfers to strobe data into
external RAM (normally connected to the WR input signal on external RAM chips).
16 / 8 (1) /
DTREQ (0)
24 Data Transfer Request or Data Bus Select. In buffered mode, input signal 16/8 used to select between the 16 bit data
transfer mode (16/8= "1") and the 8-bit data transfer mode (16/8 = "0").
In transparent mode (16-bit only), active low level output signal DTREQ used to request access to the processor/RAM
interface bus (address and data buses).
MSB / LSB (1) /
DTGRT (1)
64 Data Transfer Grant or Most Significant Byte/Least Significant Byte.
In 8-bit buffered mode, input signal (MSB/LSB) used to indicate which byte is currently being transferred (MSB or LSB).
The logic sense of MSB/LSB is controlled by the POL_SEL input. MSB/LSB is not used in the 16-bit buffered mode.
In transparent mode, active low input signal (DTGRT) asserted in response to the DTREQ output to indicate that control
of the external processor/RAM bus has been transferred from the host processor to the Enhanced Mini-ACE.
POL_SEL (1) /
DTACK (0)
29 Data Transfer Acknowledge or Polarity Select. In 16-bit buffered mode, if POL_SEL is connected to logic "1", RD/WR
should be asserted high (logic "1") for a read operation and low (logic "0") for a write operation. In 16-bit buffered
mode, if POL_SEL is connected to logic "0", RD/WR should be asserted low (logic "0") for a read operation and high
(logic "1") for a write operation.
In 8-bit buffered mode (TRANSPARENT/ BUFFERED = “0" and 16/8 = "0"), POL_SEL input signal used to control the
logic sense of the MSB/LSB signal. If POL_SEL is connected to logic “0", MSB/LSB should be asserted low (logic "0")
to indicate the transfer of the least significant byte and high (logic "1") to indicate the transfer of the most significant
byte. If POL_SEL is connected to logic “1", MSB/LSB should be asserted high (logic "1") to indicate the transfer of the
least significant byte and low (logic "0") to indicate the transfer of the most significant byte.
In transparent mode, active low output signal (DTACK) used to indicate acceptance of the processor/RAM interface bus
in response to a data transfer grant (DTGRT). The Enhanced Mini-ACE's RAM transfers over A15-A0 and D15-D0 will
be framed by the time that DTACK is asserted low.
45
PROCESSOR INTERFACE CONTROL
DESCRIPTION
SIGNAL NAME PIN
TRIG_SEL (1) /
MEMENA_IN (1)
28 Memory Enable or Trigger Select input. In 8-bit buffered mode, input signal (TRIG-SEL) used to select the order in which
byte pairs are transferred to or from the Enhanced MINI-ACE by the host processor. In the 8-bit buffered mode,
TRIG_SEL should be asserted high (logic 1) if the byte order for both read operations and write operations is MSB fol-
lowed by LSB. TRIG_SEL should be asserted low (logic 0) if the byte order for both read operations and write opera-
tions is LSB followed by MSB.
This signal has no operation in the 16-bit buffered mode (it does not need to be connected).
In transparent mode, active low input MEMENA_IN, used as a Chip Select (CS) input to the Enhanced Mini-ACE's inter-
nal shared RAM. If only internal RAM is used, should be connected directly to the output of a gate that is OR'ing the
DTACK and IOEN output signals.
MEM / REG(1)
1
Memory/Register. Generally connected to either a CPU address line or address decoder output. Selects between mem-
ory access (MEM/REG = "1") or register access (MEM/REG = "0").
SSFLAG (1) /
EXT_TRIG(1)
32 Subsystem Flag (RT) or External Trigger (BC/Word Monitor) input. In RT mode, if this input is asserted low, the
Subsystem Flag bit will be set in the ENHANCED MINI-ACE's RT Status Word. If the SSFLAG input is logic "0" while bit
8 of Configuration Register #1 has been programmed to logic "1" (cleared), the Subsystem Flag RT Status Word bit will
become logic "1," but bit 8 of Configuration Register #1, SUBSYSTEM FLAG, will return logic "1" when read. That is, the
sense on the SSFLAG input has no effect on the SUBSYSTEM FLAG register bit.
In the non-enhanced BC mode, this signal operates as an External Trigger input. In BC mode, if the external BC Start
option is enabled (bit 7 of Configuration Register #1), a low to high transition on this input will issue a BC Start com-
mand, starting execution of the current BC frame.
In the enhanced BC mode, during the execution of a Wait for External Trigger (WTG) instruction, the Enhanced Mini-ACE
BC will wait for a low-to-high transition on EXT_TRIG before proceeding to the next instruction.
In the Word Monitor mode, if the external trigger is enabled (bit 7 of Configuration Register #1), a low to high transition
on this input will initiate a monitor start.
This input has no effect in Message Monitor mode.
TRANSPARENT / 55 Used to select between the buffered mode (when strapped to logic “0”) and transparent/DMA mode (when strapped to
BUFFERED
logic “1") for the host processor interface.
READYD
56 Handshake output to host processor. For a nonzero wait state read access, READYD is asserted at the end of a host
transfer cycle to indicate that data is available to be read on D15 through D0 when asserted (low). For a nonzero wait
state write cycle, READYD is asserted at the end of the cycle to indicate that data has been transferred to a register or
RAM location. For both nonzero wait reads and writes, the host must assert STRBD low until READYD is asserted low.
In the (buffered) zero wait state mode, this output is normally logic "0", indicating that the Enhanced Mini-ACE is in a
state ready to accept a subsequent host transfer cycle. In zero wait mode, READYD will transition from low to high during
(or just after) a host transfer cycle, when the Enhanced Mini-ACE initiates its internal transfer to or from registers or inter-
nal RAM. When the Enhanced Mini-ACE completes its internal transfer, READYD returns to logic "0", indicating it is
ready for the host to initiate a subsequent transfer cycle.
IOEN(0)
58 I/O Enable. Tri-state control for external address and data buffers. Generally not used in buffered mode. When low, indi-
cates that the Enhanced Mini-ACE is currently performing a host access to an internal register, or internal or (for trans-
parent mode) external RAM. In transparent mode, IOEN (low) should be used to enable external address and data bus
tri-state buffers.
46
RT ADDRESS
DESCRIPTION
SIGNAL NAME PIN
RTAD4 (MSB) (1) 35 RT Address inputs. If bit 5 of Configuration Register #6, RT ADDRESS SOURCE, is programmed to logic "0" (default),
then the Enhanced Mini-ACE's RT address is provided by means of these 5 input signals. In addition, if RT ADDRESS
RTAD3 (1)
34
21
41
33
SOURCE is logic "0", the source of RT address parity is RTADP.
RTAD2 (1)
There are many methods for using these input signals for designating the Enhanced Mini-ACE's RT address. For details,
refer to the description of RT_AD_LAT.
RTAD1 (1)
If RT ADDRESS SOURCE is programmed to logic "1", then the Enhanced Mini-ACE's source for its RT address and par-
ity is under software control, via data lines D5-D0. In this case, the RTAD4-RTAD0 and RTADP signals are not used.
RTAD0 (LSB) (1)
RTADP (1)
40 Remote Terminal Address Parity. This input signal must provide an odd parity sum with RTAD4-RTAD0 in order for the
RT to respond to non-broadcast commands. That is, there must be an odd number of logic "1"s from among RTAD-4-
RTAD0 and RTADP.
RT_AD_LAT (1)
31 RT Address Latch. Input signal used to control the Enhanced MINI-ACE's internal RT address latch. If RT_AD_LAT is
connected to logic "0", then the Enhanced Mini-ACE RT is configured to accept a hardwired (transparent) RT address
from RTAD4-RTAD) and RTADP.
If RT_AD_LAT is initially logic "0", and then transitions to logic "1", the values presented on RTAD4-RTAD0 and RTADP
will be latched internally on the rising edge of RT_AD_LAT.
If RT_AD_LAT is connected to logic "1", then the Enhanced Mini-ACE's RT address is latchable under host processor
control. In this case, there are two possibilities: (1) If bit 5 of Configuration Register #6, RT ADDRESS SOURCE, is pro-
grammed to logic "0" (default), then the source of the RT Address is the RTAD4-RTAD0 and RTADP input signals; (2) If
RT ADDRESS SOURCE is programmed to logic "1", then the source of the RT Address is the lower 6 bits of the proces-
sor data bus, D5-D1 (for RTAD4-0) and D0 (for RTADP).
In either of these two cases (with RT_AD_LAT = "1"), the processor will cause the RT address to be latched by: (1) writ-
ing bit 15 of Configuration Register #3, ENHANCED MODE, to logic "1"; (2) writing bit 3 of Configuration Register #4,
LATCH RT ADDRESS WITH CONFIGURATION REGISTER #5, to logic "1"; and (3) writing to Configuration Register #5.
In the case of RT ADDRESS SOURCE = "1", then the values of RT address and RT address parity must be written to
the lower 6 bits of Configuration Register #5, via D5-D0. In the case where RT ADDRESS SOURCE = "0", the bit values
presented on D5-D0 become "don't care" .
47
MISCELLANEOUS
BU-61843(5) /
61743(5)
(4KK RAM)
BU-61864(5)
(64K RAM)
SIGNAL NAME
DESCRIPTION
PIN
PIN
UPADDREN
-
26
For BU-61864/61865, this pin is +5V-RAM and MUST be connected to +5V.
For BU-61743(5) and 61843(5), this signal is used to control the function of the upper 4
address inputs (A15-A12). For these versions of Enhanced Mini-ACE, if UPADDREN is
connected to logic "1", then these four signals operate as address lines A15-A12.
For BU-61843(5)/61743(5), if UPADDREN is connected to logic "0", then A15 and A14
function as CLK_SEL_1 and CLK_SEL_0 respectively; A13 MUST be connected to Vcc-
LOGIC (+5V or +3.3V); and A12 functions as RTBOOT.
INCMD (O) /
MCRST (O)
25
25
In-command or Mode Code Reset. The function of this pin is controlled by bit 0 of
Configuration Register #7, MODE CODE RESET/INCMD SELECT.
If this register bit is logic "0" (default), INCMD will be active on this pin. For BC, RT, or
Selective Message Monitor modes, INCMD is asserted low whenever a message is being
processed by the Enhanced Mini-ACE. In Word Monitor mode, INCMD will be asserted
low for as long as the monitor is online.
For RT mode, if MODE CODE RESET/INCMD SELECT is programmed to logic "1",
MCRST will be active. In this case, MCRST will be asserted low for two clock cycles fol-
lowing receipt of a Reset remote terminal mode command.
In BC or Monitor modes, if MODE CODE RESET/INCMD SELECT is logic "1", this signal
is inoperative; i.e., in this case, it will always output a value of logic "1".
INT (0)
57
57
Interrupt Request output. If the LEVEL/PULSE interrupt bit (bit 3) of Configuration
Register #2 is logic "0", a negative pulse of approximately 500ns in width is output on
INT to signal an interrupt request.
If LEVEL/PULSE is high, a low level interrupt request output will be asserted on INT. The
level interrupt will be cleared (high) after either: (1) The processor writes a value of logic
"1" to INTERRUPT RESET, bit 2 of the Start/Reset Register; or (2) If bit 4 of
Configuration Register #2, INTERRUPT STATUS AUTO-CLEAR is logic "1", then it will
only be necessary to read the Interrupt Status Register (#1 and/or #2) that is requesting
an interrupt that has been enabled by the corresponding Interrupt Mask Register.
However, for the case where both Interrupt Status Register #1 and Interrupt Status
Register #2 have bits set reflecting interrupt events, it will be necessary to read both
interrupt status registers in order to clear INT.
CLOCK_IN (1)
TX_INH_A (1)
TX_INH_B (1)
30
59
60
30
59
60
20 MHz, 16 MHz, 12 MHz, or 10 MHz clock input.
Transmitter inhibit inputs for the Channel A and Channel B MIL-STD-1553 transmitters.
For normal operation, these inputs should be connected to logic "0". To force a shutdown
of Channel A and/or Channel B, a value of logic "1" should be applied to the respective
TX_INH input.
MSTCLR(1)
2
2
Master Clear. Negative true Reset input, normally asserted low following power turn-on.
When coming out of a “reset” condition, please note that the rise time of MSTCLR must
be less than 10 µS.
FACTORY TEST
DESCRIPTION
SIGNAL NAME
PIN
XCVR_TP (ZAP VOLTA)
XCVR_TP (READOUTB)
XCVR_TP (READOUTA)
XCVR_TP (CLOCK)
P1(*) For factory test only. Do not connect for normal operation.
P2(*)
P3(*)
P4(*)
P5(*)
P6(*)
XCVR_TP (RESET)
XCVR_TP (ZAP VOLTB)
(*) Note that the Test Output pins are recessed pads located on the bottom of the package.
48
TABLE 48. PACKAGE PINOUTS
TABLE 48. PACKAGE PINOUTS
BU-61843(5)
BC / RT / MT, (4K RAM)
BU-61743(5)
BU-61843(5)
BC / RT / MT, (4K RAM)
BU-61743(5)
PACKAGE
PGA
PACKAGE
PGA
BU-61864(5)
BC / RT / MT
(64K RAM)
BU-61864(5)
BC / RT / MT
(64K RAM)
QFP
QFP
RT ONLY, (4K RAM)
RT ONLY, (4K RAM)
( NOTE 1)
( NOTE 1)
1
B4
B5
C2
C3
C1
D2
D1
C4
E3
F2
E1
F3
G1
G4
G3
H1
A7
A8
J8
MEM/REG
MEM/REG
MSTCLR
A11
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
F8
G6
G9
J9
D1
D4
D1
D4
2
MSTCLR
3
A11
RTADP
RTAD1
DO
RTADP
RTAD1
DO
4
A10
TX/RX_A
A8
A10
5
TX/RX_A
A8
H9
F9
F7
G5
E7
E9
D7
B2
D9
B9
A2
D8
A1
6
D2
D2
7
TX/RX_A
A14
TX/RX_A
A14/CLK_SEL_0
A4
D3
D3
8
D5
D5
9
A4
D8
D8
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
A3
A3
D7
D7
A7
A7
D13
D12
D14
D9
D13
D12
D14
D9
A2
A2
TX/RX_B
ADDR_LAT/MEMOE
A0
TX/RX_B
ADDR_LAT/MEMOE
A0
D11
D15
D10
D11
D15
D10
TX/RX-B
LOGIC GND
LOGIC GND
LOGIC GND
+5V Vcc-CH. B
RTAD2
TX/RX-B
LOGIC GND
LOGIC GND
LOGIC GND
+5V Vcc-CH. B
RTAD2
TRANSPARENT/
BUFFERED
TRANSPARENT/
BUFFERED
55
C9
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
B8
C8
A3
B7
C7
C6
A6
A5
J1
READYD
INT
READYD
INT
A9
J7
IOEN
IOEN
F1
J2
A6
A6
TX_INH_A
TX_INH_B
SELECT
STRBD
TX_INH_A
TX_INH_B
SELECT
ZEROWAIT/MEMWR
8/16-BIT/DTREQ
INCMD/MCRST
+5V RAM
A1
ZEROWAIT/MEMWR
8/16-BIT/DTREQ
INCMD/MCRST
UPADDREN
A1
H5
H3
H4
G2
J5
STRBD
RD / WR
MSB/LSB/DTGRT
LOGIC GND
A15
RD / WR
MSB/LSB/DTGRT
LOGIC GND
A15/CLK_SEL_1
LOGIC GND
A5
TRIG_SEL/MEMENA_IN TRIG_SEL/MEMENA_IN
A4
C5
B6
E2
J4
J6
POL_SEL/DTACK
CLOCK_IN
RT_AD_LAT
SSFLAG/ EXT_TRIG
RTAD0
POL_SEL/DTACK
CLOCK_IN
RT_AD_LAT
SSFLAG/ EXT_TRIG
RTAD0
H6
G7
H2
H7
G8
H8
E8
D3
LOGIC GND
A5
A9
A9
B3
B1
J3
A12
A12/RTBOOT
A13/+5V/3.3V LOGIC
+5V Vcc-CH. A
RTAD3
RTAD3
A13
RTAD4
RTAD4
+5V Vcc-CH. A
D6
D6
+5V/3.3V LOGIC
+5V/3.3V LOGIC
49
TABLE 48. PACKAGE PINOUTS
BU-61843(5)
BC / RT / MT, (4K RAM)
BU-61743(5)
PACKAGE
PGA
BU-61864(5)
BC / RT / MT
(64K RAM)
QFP
( NOTE 1)
RT ONLY, (4K RAM)
XCVR TP
(ZAP VOLTA)
XCVR TP
(ZAP VOLTA)
P1 **
D4
P2 **
P3 **
P4 **
P5 **
F5
D5
E4
E5
XCVR TP (READOUTB) XCVR TP (READOUTB)
XCVR TP (READOUTA) XCVR TP (READOUTA)
XCVR TP(CLOCK)
XCVR TP(CLOCK)
XCVR TP (RESET_L)
XCVR TP (RESET_L)
XCVR TP
(ZAP VOLTB)
XCVR TP
(ZAP VOLTB)
P6 **
F4
N/A
N/A
N/A
D6
E6
F6
GND
GND
GND
GND
GND
GND
** Note that the Test Output pins on the flat pack are pads located on the
bottom of the package.
NOTE 1:This column is shown for reference only.There is no PGA pack-
age for the initial product release.
50
2.000 ±0.015
(50.800 ±0.381)
1.000 SQ ±0.010
(25.400 ±0.254)
0.500 ±0.005
(12.70 ±0.127)
0.200 ±0.005
(5.080 ±0.127)
0.100 DIA.
(2.540) (see note 4)
P6
P5
P2
P4
P1
P3
72
1
INDEX DENOTES
PIN NO. 1
0.018 ±0.002 0.050 ±0.005
(1.270 ±0.127)
(0.457 ±0.051)
VIEW "B"
VIEW "A"
VIEW "B"
0.850 ±0.008
(21.590 ±0.203)
BOTTOM VIEW
0.010 ±0.002
(0.254 ±0.051)
0.050 ±0.005
(1.270 ±0.127)
0.155 MAX
(3.94)
0.040 ±0.004
(1.016 ±0.102)
0.090 ±0.010
(2.286 ±0.254)
0.035 ±0.005
VIEW "A"
(0.889 ±0.127)
SIDE VIEW
Notes:
1) Dimensions are in inches (mm).
2) Package Material: Alumina (AL O )
2
3
3) Lead Material: Kovar, Plated by 50µ in. minimum nickel under 60µ in. minimum gold.
4) There are 6 test pads located on the bottom of the package. These pads are recessed
so as not to interfere when mounting the hybrid There are no user connections to these pads.
FIGURE 16. MECHANICAL OUTLINE DRAWING FOR 72-LEAD FLATPACK
51
1.38 ±0.02
(35.05 ±0.51)
1.00 SQ ±0.01
(25.40 ±0.25)
0.19 ±0.01
(4.83 ±0.25)
0.100 DIA.
(2.540) (see note 4)
Notes:
1) Dimensions are in inches (mm).
2) Package Material: Alumina (AL O )
2 3
3) Lead Material: Kovar, Plated by 50µ in.
minimum nickel under 60µ in. minimum gold.
4) There are 6 test pads located on the bottom of
the package. These pads are recessed so as
not to interfere when mounting the hybrid.
There are no user connections to these pads.
P6
P5
P2
P4
P1
P3
72
1
VIEW "B"
0.850 ±0.008
(21.590 ±0.203)
0.018 ±0.002 0.050 ±0.005
(1.270 ±0.127)
BOTTOM VIEW
0.006 -0.004,+0.010
(0.457 ±0.051)
VIEW "B"
(0.152 -0.100,+ 0.254)
VIEW "A"
0.08 MIN FLAT
(2.03)
INDEX DENOTES
PIN NO. 1
0.012 R. MAX
(0.305 R.)
0.155 MAX
(3.94)
0.010 ±0.002
(0.254 ±0.051)
1.024 MAX TYP.
(26.010)
VIEW "A"
0.05 MIN FLAT
(1.27)
SIDE VIEW
FIGURE 17. MECHANICAL OUTLINE DRAWING FOR 72-PIN GULL LEAD PACKAGE
52
ORDERING INFORMATION
BU-61745F3-120X
Supplemental Process Requirements:
S = Pre-Cap Source Inspection
L = Pull Test
Q = Pull Test and Pre-Cap Inspection
K = One Lot Date Code
W = One Lot Date Code and PreCap Source
Y = One Lot Date Code and 100% Pull Test
Z = One Lot Date Code, PreCap Source and 100% Pull Test
Blank = None of the Above
Test Criteria:
0 = Standard Testing
2 = MIL-STD-1760 Amplitude Compliant
Process Requirements:
0 = Standard DDC practices, no Burn-In
1 = MIL-PRF-38534 Compliant
2 = B*
3 = MIL-PRF-38534 Compliant with PIND Testing
4 = MIL-PRF-38534 Compliant with Solder Dip
5 = MIL-PRF-38534 Compliant with PIND Testing and Solder Dip
6 = B* with PIND Testing
7 = B* with Solder Dip
8 = B* with PIND Testing and Solder Dip
9 = Standard DDC Processing with Solder Dip, no Burn-In
Temperature Range/Data Requirements:
1 = -55°C to +125°C
2 = -40°C to +85°C
3 = 0°C to +70°C
4 = -55°C to +125°C with Variables Test Data
5 = -40°C to +85°C with Variables Test Data
6 = Custom Part (Reserved)
7 = Custom Part (Reserved)
8 = 0°C to +70°C with Variables Test Data
Voltage/Transceiver Option:
3 = +5 Volts rise/fall times = 100 to 300 ns (-1553B)
4 = +5 Volts rise/fall times = 200 to 300 ns (-1553B and McAir compatible)
Package Type:
F = Flat Pack
G = “Gull Wing” (Formed Lead)
Logic / RAM Voltage
3 = 3.3 Volt (Applicable only for BU-61743 and BU-61843)
4 = 3.3 and 5 Volt (Applicable only for BU-61684)
5 = 5 Volt
Product Type:
BU-6174 = RT only with 4K x 16 RAM
BU-6184 = BC /RT / MT with 4K x 16 RAM
BU-6186 = BC /RT / MT with 64K x 17 RAM
STANDARD DDC PROCESSING
MIL-STD-883
TEST
METHOD(S)
CONDITION(S)
INSPECTION
SEAL
2009, 2010, 2017, and 2032
—
1014
1010
A and C
TEMPERATURE CYCLE
CONSTANT ACCELERATION
BURN-IN
C
A
2001
1015, Table 1
—
53
NOTES
54
NOTES
55
The information in this data sheet is believed to be accurate; however, no responsibility is
assumed by Data Device Corporation for its use, and no license or rights are
granted by implication or otherwise in connection therewith.
Specifications are subject to change without notice.
105 Wilbur Place, Bohemia, New York 11716-2482
For Technical Support - 1-800-DDC-5757 ext. 7382 or 7234
Headquarters - Tel: (631) 567-5600, Fax: (631) 567-7358
West Coast - Tel: (714) 895-9777, Fax: (714) 895-4988
Southeast - Tel: (703) 450-7900, Fax: (703) 450-6610
United Kingdom - Tel: +44-(0)1635-811140, Fax: +44-(0)1635-32264
Ireland - Tel: +353-21-341065, Fax: +353-21-341568
France - Tel: +33-(0)1-41-16-3424, Fax: +33-(0)1-41-16-3425
Germany - Tel: +49-(0)8141-349-087, Fax: +49-(0)8141-349-089
Sweden - Tel: +46-(0)8-54490044, Fax +46-(0)8-7550570
Japan - Tel: +81-(0)3-3814-7688, Fax: +81-(0)3-3814-7689
World Wide Web - http://www.ddc-web.com
U
®
DATA DEVICE CORPORATION
REGISTERED TO ISO 9001
FILE NO. A5976
B-05/00-500
PRINTED IN THE U.S.A.
56
相关型号:
©2020 ICPDF网 联系我们和版权申明